Download: Disassembly and Reassembly 4-1 Cabinet and PCB

Disassembly and Reassembly 4-1 Cabinet and PCB Disassemble in the order shown. (Reassemble in reverse order.) 4-1-1 Case-Side Removal 3 Disconnect 2 tabs while lifting up the case-side to the arrow direction. Bottom Side 1 Remove 2 screws. Precision screw Driver 2 Lift up the case-side using the precision screw driver. Fig. 1 Samsung Electronics 4-1 4-1-2 Door-Battery Removal Open the Door-Battery (in the direction of arrow), and twist it to remove. Fig. 2 4-1-3 Case-Rear Removal 2 Remove 3 tabs while CASE-REAR pushing "A" area down. Detach the case-rear in the direction of the arrow. A 1 Re...
Author: Folver Shared: 8/19/19
Downloads: 293 Views: 848

Content

Disassembly and Reassembly 4-1 Cabinet and PCB Disassemble in the order shown. (Reassemble in reverse order.) 4-1-1 Case-Side Removal 3 Disconnect 2 tabs while lifting up the case-side to the arrow direction. Bottom Side 1 Remove 2 screws. Precision screw Driver 2 Lift up the case-side using the precision screw driver. Fig. 1 Samsung Electronics 4-1, 4-1-2 Door-Battery Removal Open the Door-Battery (in the direction of arrow), and twist it to remove. Fig. 2 4-1-3 Case-Rear Removal 2 Remove 3 tabs while CASE-REAR pushing "A" area down. Detach the case-rear in the direction of the arrow.

A

1 Remove 1 screw. Fig. 3 4-2 Samsung Electronics, 4-1-4 Main-PCB Removal 1 Remove 2 screws. 2 Disassemble MAIN PCB while 3 Disconnect the lead connector disconnecting CN301 from FUNCTION-PCB. CN502 from JACK-PCB. Fig. 4 4-1-5 Jack-PCB Removal 3 Disconnect the lead connector from CN501. 1 Remove 1 screw. 2 Disconnect 1 tabs. Fig. 5 Samsung Electronics 4-3, 4-1-6 Case-Top Removal 1 Disconnect one tab and detach Case-Top in the direction of arrow. Fig. 6 4-1-7 Case-Front Removal 2 Detach Case-Front in the direction of arrow. 1 Remove 1 screw. Fig. 7 4-4 Samsung Electronics, 4-1-8 OVF Removal 1 Remove 1 screw. Note : Take extreme care not to ieave fingerprints on the surface. 2 Lift up OVF. Fig. 8 Samsung Electronics 4-5,

MEMO

4-6 Samsung Electronics]
15

Similar documents

  Reference Information 2-1 Circuit description 2-1-1 DSC
Reference Information 2-1 Circuit description 2-1-1 DSC Digital camera(SDC-30/33), is an image-input device that connects to a PC. It’s small and light welght, supplies high quality images and has a large capacity (4MB/2MB). The digital camera consists of 3 sections: Camera, signal processing and
  Disassembly and Reassembly 3-1. Cabinet Disassembly
Disassembly and Reassembly 3-1. Cabinet Disassembly 3-1-1. Ass’y CASE-TOP Removal Remove the INLAY. Remove the CASE-TOP. Remove 2 screws. Remove 1 screw. Remove the INLAY. Fig. 3-1 Ass’y CASE-TOP Removal Samsung Electronics 3-1 3-1-2. Ass’y CASE-BOTTOM Removal Remove the CASE-BOTTOM. Remove 1 scre
  Adjustment 5-1. Camera Adjustment
Adjustment 5-1. Camera Adjustment 5-1-1. Focus Adjustment • Adjusting in the Photo Mode 1. Connect the camera and TV to video output cable. Turn on the power and set to the PC mode. 2. Aim the Main board at the focus chart placed 2.5 meters away and perpendicular to the center of the lens. 3. Loos
  Specifications
Specifications System Specifications CCD Progressive 0.85M pixel Number of pixels 1024 x 768 pixel (XGA) Color Depth 24 bits True Color Memory capacity Extra (smart media card 4MB/3.3V) Image Capacity Standard (quality-about 20/high quality-about 10) Lens Dual fixed focus F:2.8f = 6.6 Focus Length
  Wiring Diagram
Wiring Diagram Samsung Electronics 8-1 Wiring Diagram MEMO 8-2 Samsung Electronics
  PCB Diagrams
PCB Diagrams 7-1. Main PCB (Rev.02) 7-2 7-2. Main PCB (Rev.03) 7-4 7-3. B/L PCB 7-6 7-4. DC PCB 7-8 7-5. Function PCB 7-10 7-6. Jack PCB 7-11 < Main PCB > Samsung Electronics 7-1 7-1. Main PCB (Rev.02) 7-2 Samsung Electronics Component Side Samsung Electronics 7-3 7-2. Main PCB (Rev.03) 7-4 Samsun
  Schematic Diagrams
Schematic Diagrams 9-1. CCD Block 9-2 9-2. Drive Block 9-3 9-3. Process Block 9-4 9-4. Function Block 9-5 9-5. LCD Block 9-6 9-6. JACK Block 9-7 9-7. CCD Block 9-8 9-8. Drive Block 9-9 9-9. Process Block 9-10 9-10. Function Block 9-11 Samsung Electronics 9-1 9-1. Process Block (Rev.02,03) *Rev.02
DIGITAL CAMERA SDC-80 SERVICE Manual
SERVICE MANUAL SDC-80 DIGITAL CAMERA SDC-80 SERVICE Manual DIGITAL CAMERA CONTENTS 1. Introduction 2. Specifications 3. Disassembly and Reassembly 4. Exploded View and Parts List 5. Adjustment 6. Electrical Parts List 7. PCB Diagrams 8. Wiring Diagram 9. Schematic Diagrams © Samsung Electronics Co.,
CONTENTS
CONTENTSⅠ. SPECIFICATION 1. CAMERA SPECIFICATION …………………………………………………………………………………… 4 2. System Requirements …………………………………………………………………………………………… 7 3. LCD monitor indicator …………………………………………………………………………………………… 8 4. CONNECTION DIAGRAM……………………………………………………………………………………… 11 5. IDENTIFICATION OF FEATURES …………
  OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 10987654321
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 109876543211. IC Configuration CA1 board Ye Cy Ye Cy IC903 (ICX411AK) CCD imager G Mg G IC901 (CXD3400N) V driver MgYe Cy Ye CA2 board CyG Mg G Mg IC911 (H driver, CDS, AGC and A/D converter) Ye Cy Ye C
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET BACK, CABINET FRONT AND SY2 BOARD 1. Seven screws 1.7x42. Cabinet back 2 3. Cabinet front 4. Three connectors 5. Screw 1.7x56. SY2 board 7. Cover jack457142-2. REMOVAL OF CABINET TOP AND LCD 1. Screw 1.7x42. Cabinet left 3. Screw 1.7 x 2.5 12 4. Two screws 1.7 x
SERVICE MANUAL Digital Disc Camera IDC-1000ZE IDC-1000ZEX IDC-1000ZU
FILE NO. SERVICE MANUAL Digital Disc Camera IDC-1000ZE (Product Code : 126 250 01) (U.K.) IDC-1000ZEX (Product Code : 126 250 02) (Europe) (General PAL area) IDC-1000ZU (Product Code : 126 250 03) (U.S.A.) (Canada) Contents 1. iD PHOTO DISC ... 2 8. PARTS LIST... 31 2. OUTLINE OF iD FORMAT DISC DRIV
1-4. PW1 POWER CIRCUIT DESCRIPTION
1-4. PW1 POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog System Power Output This is the main power circuit, and is comprised of the follow- 15.2 V (A) and -7.7 V (A) are output. Feedback for the 15.2 V ing blocks. (A) is provided to the switching controller (Pin (28) of IC501) Switching controller (
VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
B-Type : BL103
DIGITAL CAMERA B-Type : BL103SERVICE Manual DIGITAL CAMERA CONTENTS 1. Specification 2. Installation 3. Exploded view and Part list 4. Firmware 5. Adjustment 6. Block Diagram 7. Pattern Diagram 8. Circuit Diagram 9. Service InformationCONTENTSⅠ. SPECIFICATION 1. CAMERA SPECIFICATION……………………………………………
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS OVERALL WIRING ... C1 OVERALL CIRCUIT ... C2 CAMERA CIRCUIT ... C2 POWER CIRCUIT(CA3) ... C2 POWER CIRCUIT(PW1) ... C3 FLASH CIRCUIT ... C3 MAIN CIRCUIT ... C3 SYSTEM CONTROL CIRCUIT ... C4 CIRCUIT DIAGRAMS CA
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
  OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 10987654321
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 109876543211. IC Configuration CA1 board Ye Cy Ye Cy IC901 (ICX411AQ) CCD imager G Mg G CA2 board MgYe Cy Ye IC931 H driver, CDS, AGC and A/D converter CyG Mg G Mg IC934 (CXD3400N) V driver Ye Cy Ye Cy
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 CAMERA CIRCUIT ... C4 FLASH CIRCUIT ... C5 POWER CIRCUIT ... C5 LENS CIRCUIT ... C5 MAIN & LCD DRIVER CIRCUIT ... C6 SYSTEM CONTROL CIRCUIT ... C7 CIRCUIT DIAG
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
SERVICE MANUAL Color Digital Camera VPC-AZ1EX VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
  ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment
ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment 6-4. LCD Blue Brightness Adjustment Ref. No. Name Number Part code 6-5. LCD Red Brightness Adjustment J-1 Pattern box (color viewer) 1 VJ8-0190 Note: If the lens, CCD and board in item 2-5, it is necessary to adjus
1-4. ST1 STROBE CIRCUIT DESCRIPTION
1-4. ST1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When RDY and TRIG signals are input from the ASIC expan- CHG signal from SY1 board becomes High (3.3 V), the charg- sion port, the stroboscope emits light. ing
SERVICE MANUAL Digital Movie Camera VPC-C40 VPC-C40EX
FILE NO. SERVICE MANUAL Digital Movie Camera VPC-C40 (Product Code : 168 033 01) (U.S.A.) (Canada) (Korea) (Taiwan) VPC-C40EX (Product Code : 168 033 02) (Europe) (South America) (China) (Australia) (Hong Kong) Contents (Russia) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Middle East) 2. DISASSEMBLY ..
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET LEFT, CP1 BOARD AND SY1 BOARD 1. Cover battery 9. Screw 1.7x32. Five screws 1.7x510. Shield CP1 3. Three screws 1.7x311. CP1 board 4. Cabinet left 12. Two connectors 5. Cover card 13. Two FPCs 6. Connector 14. Four screws 1.7x412 7. FPC 15. Connector 8. Screw 1.
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 POWER CIRCUIT ... C5 STROBO CIRCUIT ... C5 CAMERA CIRCUIT ... C6 LENS DRIVER CIRCUIT ... C6 MAIN CIRCUIT ... C7 SYSTEM CONTROL CIRCUIT ... C8 CIRCUIT DIAGRAMS
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol-
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur