Download: OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 10987654321

OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 109876543211. IC Configuration CA1 board Ye Cy Ye Cy IC903 (ICX411AK) CCD imager G Mg G IC901 (CXD3400N) V driver MgYe Cy Ye CA2 board CyG Mg G Mg IC911 (H driver, CDS, AGC and A/D converter) Ye Cy Ye Cy G Mg G 2. IC903 (CCD imager) Mg (Note) Horizontal register [Structure] Interline type CCD image sensor Image size Diagonal 8.293 mm (1/1.8 type) 11 12 13 14 15 16 17 18 19 20 Pixels in total 2384 (H) x 1734 (V) Recording pixels 2288 (H) x 1712 (V) (Note) : Photo sensor Fig. 1-2. CCD Block Diagram ...
Author: Folver Shared: 8/19/19
Downloads: 557 Views: 4180

Content

OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT

DESCRIPTIONS Around CCD block 10987654321

1. IC Configuration CA1 board Ye Cy Ye Cy IC903 (ICX411AK) CCD imager G Mg G IC901 (CXD3400N) V driver MgYe Cy Ye CA2 board CyG Mg G Mg IC911 (H driver, CDS, AGC and A/D converter) Ye Cy Ye Cy G Mg G 2. IC903 (CCD imager) Mg (Note) Horizontal register [Structure] Interline type CCD image sensor Image size Diagonal 8.293 mm (1/1.8 type) 11 12 13 14 15 16 17 18 19 20 Pixels in total 2384 (H) x 1734 (V) Recording pixels 2288 (H) x 1712 (V) (Note) : Photo sensor Fig. 1-2. CCD Block Diagram Pin No. Symbol Pin Description Waveform Voltage 1 Vø4 Vertical register transfer clock -7.5 V, 0 V 2, 3 Vø3A, Vø3B Vertical register transfer clock -7.5 V, 0 V, 15V4Vø2 Vertical register transfer clock -7.5 V, 0 V 5, 6 Vø1A, Vø1B Vertical register transfer clock -7.5 V, 0 V, 15 V 9, 15 GND GND GND0V10 VOUT Signal output Aprox. 10 V 11 VDD Circuit power DC 15 V 12 øRG Reset gate clock 12.5 V, 16 V 13, 20 Hø2 Horizontal register transfer clock 0 V, 5 V 14, 19 Hø1 Horizontal register transfer clock 0 V, 5 V 16 øSUB Substrate clock DC Approx. 8 V Approx. 8 V 17 CSUB Substrate bias DC (Different from every CCD) 18 VL Protection transistor bias DC Table 1-1. CCD Pin Description When sensor read-out – 2 – VDD VOUT ØRG GNDHØ2TESTHØ1TEST Vertical register GNDVØ1B ØSUBVØ1A CSUBVØ2VLVØ3BHØ1VØ3AHØ2VØ 4, 3. IC901 (V Driver) and IC911 (H Driver) 5. Lens drive block An H driver and V driver are necessary in order to generate 5-1. Iris and shutter drive the clocks (vertical transfer clock, horizontal transfer clock The shutter and iris stepping motor drive signals (IIN1, IIN2, and electronic shutter clock) which driver the CCD. IIN3 and IIN4) which are output from the ASIC (IC102) are IC901 is V driver. In addition the XV1-XV4 signals which are used to drive by the motor driver (IC951), and are then used to output from IC102 are the vertical transfer clocks, and the drive the iris steps. XSG signal which is output from IC102 is superimposed onto XV1 and XV3 at IC901 in order to generate a ternary pulse. 5-2. Focus drive In addition, the XSUB signal which is output from IC102 is The focus stepping motor drive signals (FIN1, FIN2, FIN3 and used as the sweep pulse for the electronic shutter. A H driver FIN4) which are output from the ASIC expansion port (IC107) is inside IC911, and H1, H2 and RG clock are generated at are used to drive by the motor driver (IC952). Detection of the IC911. standard focusing positions is carried out by means of the photointerruptor (PI) inside the lens block. 4. IC911 (CDS, AGC Circuit and A/D Converter) The video signal which is output from the CCD is input to Pin 5-3. Zoom drive (29) of IC911. There are inside the sampling hold block, AGC The zoom stepping motor drive signals (ZIN1, ZIN2, ZIN3 and block and A/D converter block. ZIN4) which are output from the ASIC expansion port (IC107) The setting of sampling phase and AGC amplifier is carried are used to drive by the motor driver (IC952). Detection of the out by serial data at Pin (37) of IC911. The video signal is standard zoom positions is carried out by means of carried out A/D converter, and is output by 12-bit. photoreflector (ZPI) inside the lens block. VRT VRB

VREF

2~36 dB CCDIN CDS PxGA VGA ADC DOUT CLAMP CLAMP

INTERNAL

CLOCKS CLPOB

CLPDM PBLK

RG HORIZONTAL PRECISION4 DRIVERS TIMING CLIH1-H4 CORE SYNC INTERNAL GENERATOR REGISTERS HD VD SL SCK SDATA Fig. 1-2. IC911 Block Diagram – 3 –, 1-2. CA2 CIRCUIT DESCRIPTION 1. Circuit Description 2. Outline of Operation 1-1. Digital clamp When the shutter opens, the reset signals (ASIC and CPU) The optical black section of the CCD extracts averaged val- and the serial signals (“take a picture” commands) from the ues from the subsequent data to make the black level of the 8-bit microprocessor are input and operation starts. CCD output data uniform for each line. The optical black sec- When the TG/SG drives the CCD, picture data passes through tion of the CCD averaged value for each line is taken as the the A/D and CDS, and is then input to the ASIC as 12-bit sum of the value for the previous line multiplied by the coeffi- data. The AF, AE, AWB, shutter, and AGC value are com- cient k and the value for the current line multiplied by the puted from this data, and three exposures are made to obtain coefficient 1-k. the optimum picture. The data which has already been stored in the SDRAM is read by the CPU and color generation is 1-2. Signal processor carried out. Each pixel is interpolated from the surrounding 1. γ correction circuit data as being either Ye, Cy, Mg or B primary color data to This circuit performs (gamma) correction in order to maintain produce R, G and B data. At this time, correction of the lens a linear relationship between the light input to the camera distortion which is a characteristic of wide-angle lenses is and the light output from the picture screen. carried out. After AWB and γ processing are carried out, a matrix is generated and aperture correction is carried out for 2. Color generation circuit the Y signal, and the data is then compressed by JPEG and This circuit converts the CCD data into RGB signals. is then written to card memory (smart media). When the data is to be output to an external device, it is taken 3. Matrix circuit data from the memory and output via the USART. When played This circuit generates the Y signals, R-Y signals and B-Y sig- back on the LCD and monitor, data is transferred from memery nals from the RGB signals. to the SDRAM, and the image is then elongated so that it is displayed over the SDRAM display area. 4. Horizontal and vertical aperture circuit This circuit is used gemerate the aperture signal. 3. LCD Block During monitoring, YUV conversion is carried out for the 12- 1-3. AE/AWB and AF computing circuit bit CCD data which is input from the A/D conversion block to The AE/AWB carries out computation based on a 64-segment the ASIC and is then transferred to the DRAM so that the screen, and the AF carries out computations based on a 6- CCD data can be displayed on the LCD. segment screen. The data which has accumulated in the DRAM is passed through the NTSC encoder , and after D/A conversion is car- 1-4. SDRAM controller ried out to change the data into a Y/C signal, the data is sent This circuit outputs address, RAS, CAS and AS data for con- to the LCD panel and displayed. trolling the SDRAM. It also refreshes the SDRAM. If the shutter button is pressed in this condition, the 12-bit data which is output from the A/D conversion block of the 1-5. Communication control CCD is sent to the DRAM (DMA transfer), and after proces- 1. SIO sor, it is displayed on the LCD as a freeze-frame image. This is the interface for the 8-bit microprocessor. During playback, the JPEG image data which has accumu- lated in the flash memory is converted to YUV signals, and 2. PIO/PWM/SIO for LCD then in the same way as during monitoring, it is passed through 8-bit parallel input and output makes it possible to switch be- the NTSC endoder, and after D/A conversion is carried out to tween individual input/output and PWM input/output. change the data into a Y/C signal, the data is sent to the LCD panel and displayed. 1-6. TG/SG The two analog signal (Y/C signals) from the ASIC are con- Timing generated for 4 million pixel CCD control. verted into RGB signals by the LCD driver, and these RGB signals and the control signal which is output by the LCD driver 1-7. Digital encorder are used to drive the LCD panel. The RGB signals are 1H It generates chroma signal from color difference signal. transposed so that no DC component is present in the LCD element, and the two horizontal shift register clocks drive the horizontal shift registers inside the LCD panel so that the 1H transposed RGB signals are applied to the LCD panel. Be- cause the LCD closes more as the difference in potential be- tween the COM (common polar voltage: fixed at DC) and the R, G and B signals becomes greater, the display becomes darker; if the difference in potential is smaller, the element opens and the LCD become brighter. – 4 –, 1-3. CA3 CIRCUIT DESCRIPTION 1. Outline 3. Lens system 3.4 V Power Output This is the main CA3 power block, and is comprised of the 3.4 V (D) C is output for lens. Feedback for the 3.4 V (D) is following blocks. provided to the swiching controller (Pin (8) of IC511) so that Switching controller (IC511) PWM control can be carried out. Lens system 3.4 V power output (L5106, Q5104, D5105, C5117) 4. Backlight Power Output Backlight power output (L5102, Q5101, C5113) 10 mA (L) is output. The backlighting turns on when current LCD system power output (Q5107, T5101) flows in the direction from pin (1) to pin (2) of CN531. At this time, a feedback signal is sent from pin (2) of CN531 to pin 2. Switching Controller (IC511) (12) of IC511 through R5122 so that PWM control is carried This is the basic circuit which is necessary for controlling the out to keep the current at a constant level (10 mA). power supply for a PWM-type switching regulator, and is pro- vided with six built-in channels. They are CH5 (lens system 5. LCD System Power Output 3.4 V), CH4 (backlight) and CH3 (LCD system). CH1, CH2 12.4 V (L), 15 V (L) and4V(L) are output. Feedback for the and CH6 are not used. Feedback from 3.4 V (D) C (CH5) and 12.4 V (L) is provided to the switching controller (Pin (28) of +12.4 V (L) power supply output are received, and the PWM IC511) so that PWM control can be carried out. duty is varied so that each one is maintained at the correct voltage setting level. CH4 is feedback from 10 mA power sup- ply output are received, and the PWM duty is varied so that each one is maintained at the correct voltage setting level. 2-1. Short-circuit protection circuit If output is short-circuited for the length of time determined by the condenser which is connected to Pin (18) of IC511, all output is turned off. The control signal (P(A) ON, LCD ON and BL ON) are recontrolled to restore output. – 5 –]
15

Similar documents

  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET BACK, CABINET FRONT AND SY2 BOARD 1. Seven screws 1.7x42. Cabinet back 2 3. Cabinet front 4. Three connectors 5. Screw 1.7x56. SY2 board 7. Cover jack457142-2. REMOVAL OF CABINET TOP AND LCD 1. Screw 1.7x42. Cabinet left 3. Screw 1.7 x 2.5 12 4. Two screws 1.7 x
SERVICE MANUAL Digital Disc Camera IDC-1000ZE IDC-1000ZEX IDC-1000ZU
FILE NO. SERVICE MANUAL Digital Disc Camera IDC-1000ZE (Product Code : 126 250 01) (U.K.) IDC-1000ZEX (Product Code : 126 250 02) (Europe) (General PAL area) IDC-1000ZU (Product Code : 126 250 03) (U.S.A.) (Canada) Contents 1. iD PHOTO DISC ... 2 8. PARTS LIST... 31 2. OUTLINE OF iD FORMAT DISC DRIV
1-4. PW1 POWER CIRCUIT DESCRIPTION
1-4. PW1 POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog System Power Output This is the main power circuit, and is comprised of the follow- 15.2 V (A) and -7.7 V (A) are output. Feedback for the 15.2 V ing blocks. (A) is provided to the switching controller (Pin (28) of IC501) Switching controller (
VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
B-Type : BL103
DIGITAL CAMERA B-Type : BL103SERVICE Manual DIGITAL CAMERA CONTENTS 1. Specification 2. Installation 3. Exploded view and Part list 4. Firmware 5. Adjustment 6. Block Diagram 7. Pattern Diagram 8. Circuit Diagram 9. Service InformationCONTENTSⅠ. SPECIFICATION 1. CAMERA SPECIFICATION……………………………………………
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS OVERALL WIRING ... C1 OVERALL CIRCUIT ... C2 CAMERA CIRCUIT ... C2 POWER CIRCUIT(CA3) ... C2 POWER CIRCUIT(PW1) ... C3 FLASH CIRCUIT ... C3 MAIN CIRCUIT ... C3 SYSTEM CONTROL CIRCUIT ... C4 CIRCUIT DIAGRAMS CA
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
  OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 10987654321
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 109876543211. IC Configuration CA1 board Ye Cy Ye Cy IC901 (ICX411AQ) CCD imager G Mg G CA2 board MgYe Cy Ye IC931 H driver, CDS, AGC and A/D converter CyG Mg G Mg IC934 (CXD3400N) V driver Ye Cy Ye Cy
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 CAMERA CIRCUIT ... C4 FLASH CIRCUIT ... C5 POWER CIRCUIT ... C5 LENS CIRCUIT ... C5 MAIN & LCD DRIVER CIRCUIT ... C6 SYSTEM CONTROL CIRCUIT ... C7 CIRCUIT DIAG
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
SERVICE MANUAL Color Digital Camera VPC-AZ1EX VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
  ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment
ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment 6-4. LCD Blue Brightness Adjustment Ref. No. Name Number Part code 6-5. LCD Red Brightness Adjustment J-1 Pattern box (color viewer) 1 VJ8-0190 Note: If the lens, CCD and board in item 2-5, it is necessary to adjus
1-4. ST1 STROBE CIRCUIT DESCRIPTION
1-4. ST1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When RDY and TRIG signals are input from the ASIC expan- CHG signal from SY1 board becomes High (3.3 V), the charg- sion port, the stroboscope emits light. ing
SERVICE MANUAL Digital Movie Camera VPC-C40 VPC-C40EX
FILE NO. SERVICE MANUAL Digital Movie Camera VPC-C40 (Product Code : 168 033 01) (U.S.A.) (Canada) (Korea) (Taiwan) VPC-C40EX (Product Code : 168 033 02) (Europe) (South America) (China) (Australia) (Hong Kong) Contents (Russia) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Middle East) 2. DISASSEMBLY ..
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET LEFT, CP1 BOARD AND SY1 BOARD 1. Cover battery 9. Screw 1.7x32. Five screws 1.7x510. Shield CP1 3. Three screws 1.7x311. CP1 board 4. Cabinet left 12. Two connectors 5. Cover card 13. Two FPCs 6. Connector 14. Four screws 1.7x412 7. FPC 15. Connector 8. Screw 1.
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 POWER CIRCUIT ... C5 STROBO CIRCUIT ... C5 CAMERA CIRCUIT ... C6 LENS DRIVER CIRCUIT ... C6 MAIN CIRCUIT ... C7 SYSTEM CONTROL CIRCUIT ... C8 CIRCUIT DIAGRAMS
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol-
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 POWER CIRCUIT ... C5 STROBO CIRCUIT ... C5 CAMERA CIRCUIT ... C6 LENS CIRCUIT ... C6 MAIN CIRCUIT ... C7 SYSTEM CONTROL CIRCUIT ... C8 CIRCUIT DIAGRAMS CIRCUIT
SERVICE MANUAL Digital Movie Camera VPC-C6 VPC-C6EX
FILE NO. SERVICE MANUAL Digital Movie Camera VPC-C6 (Product Code : 168 034 01) (U.S.A.) (Canada) (Korea) (Taiwan) VPC-C6EX (Product Code : 168 034 02) (China) (South America) (Russia) (Middle East) (Africa) (Hong Kong) (Australia) (General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 VPC-C6E 2
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 ASIC CIRCUIT ... C4 CAMERA CIRCUIT ... C5 LENS CIRCUIT ... C5 SYSTEM CONTROL CIRCUIT ... C6 STROBO CIRCUIT ... C7 POWER CIRCUIT ... C7 CIRCUIT DIAGRAMS MAIN &
  OUTLINE OF CIRCUIT DESCRIPTION
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CCD CIRCUIT DESCRIPTION Pin 1 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. V IC903 (MN39830PLJ-A) CCD imager IC901 (AN20112A) V driver 6 IC905 (AD9996BBCZ) CDS, AGC, A/D converter, H driver, vertical TG 12 H 58P
VPC-E6EX VPC-E6EXW
FILE NO. SERVICE MANUAL Digital Camera VPC-E6 (Product Code : 168 026 01) (Canada) (Korea) (Taiwan) VPC-E6EX (Product Code : 168 026 02) VPC-E6EXW (Product Code : 168 026 04) (Europe) (South America) (China) (Australia) Contents (General) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET FRONT AND CP1 BOARD 1. Three screws 1.7x510. Remove the solder. (microphone) 2. Three screws 1.7x411. Remove the solder. 3. Cabinet front 12. Three FPCs 4. Holder cover baria 13. Screw 1.7x35. Cover lens 14. Screw 1.7 x 3.5 6. FPC 15. Connector 7. Two screws 1.7
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 ASIC CIRCUIT ... C4 CAMERA CIRCUIT ... C5 LENS CIRCUIT ... C5 SYSTEM CONTROL CIRCUIT ... C6 STROBO CIRCUIT ... C7 POWER CIRCUIT ... C7 CIRCUIT DIAGRAMS MAIN &
SERVICE MANUAL Digital Camera VPC-E60 VPC-E60EX
FILE NO. SERVICE MANUAL Digital Camera VPC-E60 (Product Code : 168 054 01) (U.S.A.) (Canada) (Korea) (Taiwan) (General) VPC-E60EX (Product Code : 168 054 02) (Europe) (U.K.) (South America) (China) (Australia) Contents (Hong Kong) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Russia) 2. DISASSEMBLY ... 1
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur