Download: DISASSEMBLY

DISASSEMBLY 2-1. REMOVAL OF CABINET BACK, CABINET FRONT AND SY2 BOARD 1. Seven screws 1.7x42. Cabinet back 2 3. Cabinet front 4. Three connectors 5. Screw 1.7x56. SY2 board 7. Cover jack457142-2. REMOVAL OF CABINET TOP AND LCD 1. Screw 1.7x42. Cabinet left 3. Screw 1.7 x 2.5 12 4. Two screws 1.7 x 2.5 6 13 5. Cabinet top 6. Screw 1.7 x 3.5977. Screw 1.7x48. FPC489. Unit control panel 11 10. Connector 11. FPC 10 12. LCD 13. Three screws 1.7x414 14. Holder monitor – 11 – 2-3. REMOVAL OF LENS ASSEMBLY AND CA1 BOARD 1. Connector E 68 2. FPC 3. FPC 4. Three screws 1.7x45. Lens assembly 6. Two scr...
Author: Folver Shared: 8/19/19
Downloads: 1218 Views: 2646

Content

DISASSEMBLY 2-1. REMOVAL OF CABINET BACK, CABINET FRONT AND SY2 BOARD 1. Seven screws 1.7x42. Cabinet back 2 3. Cabinet front 4. Three connectors 5. Screw 1.7x56. SY2 board 7. Cover jack457142-2. REMOVAL OF CABINET TOP AND LCD 1. Screw 1.7x42. Cabinet left 3. Screw 1.7 x 2.5 12 4. Two screws 1.7 x 2.5 6 13 5. Cabinet top 6. Screw 1.7 x 3.5977. Screw 1.7x48. FPC489. Unit control panel 11 10. Connector 11. FPC 10 12. LCD 13. Three screws 1.7x414 14. Holder monitor – 11 –, 2-3. REMOVAL OF LENS ASSEMBLY AND CA1 BOARD 1. Connector E 68 2. FPC 3. FPC 4. Three screws 1.7x45. Lens assembly 6. Two screws 1.7x57. Sheild tape CA1 lens 8. CA1 board – 12 –, 2-4. REMOVAL OF SY1 BOARD, PW1 BOARD, CA3 BOARD AND CA2 BOARD 1. Two screws 1.7x42. Connector 3. SY1 board23C4. Four screws 1.7x48black 5. PW1 board A gray pink 6. Two screws 1.7 x 3.5 white D blue 7. Two screws 1.7x411 8. Two screws 1.7 x 3.5 9. Holder battery 10. Two connectors 11. Holder card 12. Connector 10 13. CA3 board 17 14. Two screws 1.7x4913 15. CA2 board 16. Holder lens A 17. Holder chassis 12

E

pink C redDB

B

red 14 15 gray blue64white black 2-5. BOARD LOCATION SY1 board CA1 board CA2 board SY2 board PW1 board CA3 board – 13 –, 3. ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 3-4. Setup 1. System requirements Ref. No. Name Part code Windows 98 or Me IBM R -compatible PC with pentium processor J-1 Color viewer 5,100 K VJ8-0007 CD-ROM drive J-2 Siemens star chart 3.5-inch high-density diskette drive J-3 Calibration software VJ8-0184 USB port J-4 Spare lamp VJ8-0028 40 MB RAM Hard disk drive with at least 15 MB available Note: J-1 color viewer is 100 - 110 VAC only. VGA or SVGA monitor with at least 256-color display

J-1 J-2 2. Installing calibration software

1. Insert the calibration software installation diskette into your diskette drive. 2. Open the explorer. 3. Copy the DscCalDI_128 folder on the floppy disk in the FD drive to a folder on the hard disk. 3. Installing USB drive Install the USB drive with camera or connection kit for PC. 4. Color Viewer

J-3 J-4 1. Turn on the switch and wait for 30 minutes for aging to take

place before using Color Pure. 2. The luminance adjustment control on the color viewer should be set to around the middle position (memory 5) during use. 3. The fluorescent lamps which are used in the color viewer are consumable parts. After the cumulative usage time reaches 2000 hours, the color temperature will start to in- crease as the usage time increases, and correct adjust- ment will not be possible. When the cumulative usage time reaches 2000 hours, all of the fluorescent lamps should be simultaneously replaced with new lamps. 3-2. Equipment 1. Oscilloscope 2. Digital voltmeter 5. Computer screen during adjustment 3. AC adaptor 4. PC (IBM R -compatible PC, Pentium processor, Window Calibration Upload LCD 98 or Me) AWB Firmware R Bright B Bright VCOMDC Focus Image RGB Offset Gain VCOMPP 3-3. Adjustment Items and Order UV Matrix 1. IC511 Oscillation Frequency Adjustment Cal Mode Initialize Tint Phase 2. Lens Adjustment OK EVF VCO 3. AWB Adjustment Cal Data H AFC Test LCD Type

OK

4. Color Adjustment Setting 5. CCD White Point Defect Detect Adjustment Language 6. CCD Black Point Defect Detect Adjustment USB storage Get VID Set Serial Set Video Mode 7. LCD Panel Adjustment Set PID Set Rev. Set 7-1. LCD H AFC Adjustment 7-2. LCD RGB Offset Adjustment 7-3. LCD Gain Adjustment 7-4. LCD Red Brightness Adjustment 7-5. LCD Blue Brightness Adjustment Note: If the lens, CCD and board and changing the part in item 2-6 replace, it is necessary to adjust again. Item 3- 5 adjustments should be carried out in sequence. Item 6 adjustments should be carried out after item 3. – 14 –, 3-5. Connecting the camera to the computer 1. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector. 2. Locate a USB port on your computer. AC adaptor USB cable To USB port – 15 –, 3-6. Adjust Specifications 2. Lens Adjustment [CA3 board (Side A)] CL578 VR513 CL407 (CSYNC) Camera Approx. CL402(G) 150 cm 3 cm CL404 (XENB) Siemens CL401(B) CL403(R) star chart Preparation: Note: POWER switch: ON 1. Voltage adjustment is necessary to repair in the CA3 board Adjustment condition: and replace the parts. More than A3 size siemens star chart 2. Power voltage set about +3.0 V. Fluorescent light illumination with no flicker Preparation: Illumination above the subject should be 400 lux ± 10 %. 1. Carry out the voltage adjustments disconnecting cabinet Adjustment method: back. 1. Set the siemens star chart 150 cm ± 3 cm so that it be- 2. Insert the compact flash. comes center of the screen. 3. Set the main switch to the camera mode. 2. Double-click on the DscCalDi128. 4. Set the selector dial to the still image shooting mode. 3. Click the Focus, and click the Yes. 5. Push the power switch, and comfirm that the through screen 4. Lens adjustment value will appear on the screen. from the CCD can be seen on the LCD. 5. Click the OK. 1. IC511 Oscillation Frequency Adjustment 3. AWB Adjustment Measuring Point CL578 Measuring Equipment Frequency counter ADJ. Location VR513 ADJ. Value 495 ± 2 kHz Adjustment method: 1. Adjust with VR513 to 495 ± 2 kHz. Camera All white pattern Color viewer Preparation: POWER switch: ON Adjusting method: 1. When setting the camera in place, set it to an angle so that nothing appears in any part of the color viewer except the white section. (Do not enter any light.) – 16 –, 2. Double-click on the DscCalDi128. 6. CCD Black Point Defect Detect Adjustment 3. Click the AWB, and click the Yes. 4. AWB adjustment value will appear on the screen. 5. Click the OK. 4. Color Adjustment Camera All white pattern Color viewer Camera Preparation: POWER switch: ON All white pattern color Adjusting method: viewer and color matrix 1. When setting the camera in place, set it to an angle so adjustment chart that nothing appears in any part of the color viewer ex- cept the white section. (Do not enter any light.) Preparation: 2. Double-click on the DscCalDi128. POWER switch: ON 3. Select “CCD Black” on the LCD “Test”, and click the “Yes”. Adjustment method: 4. After the adjustment is completed, the number of defect 1. Set the color adjustment chart to the color viewer. will appear. (Do not enter any light.) 2. Set the color adjustment chart so that it becomes center 7. LCD Panel Adjustment of the screen. [CA3 board (Side A)] 3. Double-click on the DscCalDi128. 4. Click the “UV Matrix”, and Click the “Yes”. 5. Adjustment values will appear on the screen. 6. Click the OK. 5. CCD White Point Defect Detect Adjustment Preparation: POWER switch: ON Adjustment method: CL578 1. Double-click on the DscCalDi128. 2. Select “CCD Defect” on the LCD “Test”, and click the “Yes”. VR513 3. After the adjustment is completed, the number of defect CL407 will appear. (CSYNC) CL402(G) CL404 (XENB) CL401(B) CL403(R) 7-1. LCD H AFC Adjustment Preparation: POWER switch: ON Adjusting method: 1. Double-click on the DscCalDi128. 2. Select 0 on the LCD “H AFC”. 3. Apply a trigger using CL407, and adjust LCD “H AFC” so that the time A from the rising signal at CL407 to the fall- ing signal at CL404 is 5.26 ± 0.2 µsec. – 17 –, Note: ○ ○ A 7-2. LCD RGB Offset adjustment and 7-3. LCD Gain adjust-○ ○ ○ ment should always be carried out first. ○ CL404 ○ ○ CL407 ○ ○ Enlargement

VG

○ ○

A

○ ○ ○ ○ CL404 ○ ○ ○ CL402 waveform ○ CL407 7-2. LCD RGB Offset Adjustment Adjusting method: (VG–0.1) ± 1. Adjust LCD “RGB Offset” so that the amplitude of the CL402 0.05 Vp-p waveform is 4.0 V ± 0.1 Vp-p. CL403 waveform 4.0 V ± 7-5. LCD Blue Brightness Adjustment 0.1 Vp-p Adjusting method: 1. Adjust LCD “B Bright” so that the amplitude of the CL401 waveform is (VG+0.2) ± 0.05 Vp-p with respect to the CL402 (VG) waveform. Note: CL402 waveform 7-2. LCD RGB Offset adjustment and 7-3. LCD Gain adjust- ment have done. 7-3. LCD Gain Adjustment Adjusting method: 1. Adjust LCD “Gain” so that the amplitude of the CL402 wave- form is 7.3 V ± 0.3 Vp-p. Note: 7-2. LCD RGB Offset adjustment should always be carried out first. VG CL402 waveform 7.3 V ± 0.3 Vp-p (VG+0.2) ± 0.05Vp-p CL402 waveform 7-4. LCD Red Brightness Adjustment Adjusting method: 1. Adjust LCD “R Bright” so that the amplitude of the CL403 CL401 waveform waveform is (VG–0.1) ± 0.05 Vp-p with respect to the CL402 (VG) waveform. – 18 –]
15

Similar documents

SERVICE MANUAL Digital Disc Camera IDC-1000ZE IDC-1000ZEX IDC-1000ZU
FILE NO. SERVICE MANUAL Digital Disc Camera IDC-1000ZE (Product Code : 126 250 01) (U.K.) IDC-1000ZEX (Product Code : 126 250 02) (Europe) (General PAL area) IDC-1000ZU (Product Code : 126 250 03) (U.S.A.) (Canada) Contents 1. iD PHOTO DISC ... 2 8. PARTS LIST... 31 2. OUTLINE OF iD FORMAT DISC DRIV
1-4. PW1 POWER CIRCUIT DESCRIPTION
1-4. PW1 POWER CIRCUIT DESCRIPTION 1. Outline 3. Analog System Power Output This is the main power circuit, and is comprised of the follow- 15.2 V (A) and -7.7 V (A) are output. Feedback for the 15.2 V ing blocks. (A) is provided to the switching controller (Pin (28) of IC501) Switching controller (
VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
B-Type : BL103
DIGITAL CAMERA B-Type : BL103SERVICE Manual DIGITAL CAMERA CONTENTS 1. Specification 2. Installation 3. Exploded view and Part list 4. Firmware 5. Adjustment 6. Block Diagram 7. Pattern Diagram 8. Circuit Diagram 9. Service InformationCONTENTSⅠ. SPECIFICATION 1. CAMERA SPECIFICATION……………………………………………
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE
CIRCUIT DIAGRAMS & PARTS POSITION FIGURE TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS OVERALL WIRING ... C1 OVERALL CIRCUIT ... C2 CAMERA CIRCUIT ... C2 POWER CIRCUIT(CA3) ... C2 POWER CIRCUIT(PW1) ... C3 FLASH CIRCUIT ... C3 MAIN CIRCUIT ... C3 SYSTEM CONTROL CIRCUIT ... C4 CIRCUIT DIAGRAMS CA
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
  OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 10987654321
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CA1 and A PART OF CA2 CIRCUIT DESCRIPTIONS Around CCD block 109876543211. IC Configuration CA1 board Ye Cy Ye Cy IC901 (ICX411AQ) CCD imager G Mg G CA2 board MgYe Cy Ye IC931 H driver, CDS, AGC and A/D converter CyG Mg G Mg IC934 (CXD3400N) V driver Ye Cy Ye Cy
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 CAMERA CIRCUIT ... C4 FLASH CIRCUIT ... C5 POWER CIRCUIT ... C5 LENS CIRCUIT ... C5 MAIN & LCD DRIVER CIRCUIT ... C6 SYSTEM CONTROL CIRCUIT ... C7 CIRCUIT DIAG
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
SERVICE MANUAL Color Digital Camera VPC-AZ1EX VPC-AZ1E VPC-AZ1
FILE NO. SERVICE MANUAL Color Digital Camera VPC-AZ1EX (Product Code : 126 299 01) (Europe) (PAL General) VPC-AZ1E (Product Code : 126 299 02) (U.K.) VPC-AZ1 (Product Code : 126 299 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTMENT
  ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment
ELECTRICAL ADJUSTMENT 3-1. Table for Servicing Tools 6-3. LCD RGB Offset Adjustment 6-4. LCD Blue Brightness Adjustment Ref. No. Name Number Part code 6-5. LCD Red Brightness Adjustment J-1 Pattern box (color viewer) 1 VJ8-0190 Note: If the lens, CCD and board in item 2-5, it is necessary to adjus
1-4. ST1 STROBE CIRCUIT DESCRIPTION
1-4. ST1 STROBE CIRCUIT DESCRIPTION 1. Charging Circuit 2. Light Emission Circuit When UNREG power is supplied to the charge circuit and the When RDY and TRIG signals are input from the ASIC expan- CHG signal from SY1 board becomes High (3.3 V), the charg- sion port, the stroboscope emits light. ing
SERVICE MANUAL Digital Movie Camera VPC-C40 VPC-C40EX
FILE NO. SERVICE MANUAL Digital Movie Camera VPC-C40 (Product Code : 168 033 01) (U.S.A.) (Canada) (Korea) (Taiwan) VPC-C40EX (Product Code : 168 033 02) (Europe) (South America) (China) (Australia) (Hong Kong) Contents (Russia) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Middle East) 2. DISASSEMBLY ..
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET LEFT, CP1 BOARD AND SY1 BOARD 1. Cover battery 9. Screw 1.7x32. Five screws 1.7x510. Shield CP1 3. Three screws 1.7x311. CP1 board 4. Cabinet left 12. Two connectors 5. Cover card 13. Two FPCs 6. Connector 14. Four screws 1.7x412 7. FPC 15. Connector 8. Screw 1.
SERVICE MANUAL Digital Camera VPC-AZ3EX VPC-AZ3
FILE NO. SERVICE MANUAL Digital Camera VPC-AZ3EX (Product Code : 126 621 01) (Europe) (PAL General) VPC-AZ3 (Product Code : 126 621 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ...
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
  USB STORAGE INFORMATION REGISTRATION
USB STORAGE INFORMATION REGISTRATION USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 POWER CIRCUIT ... C5 STROBO CIRCUIT ... C5 CAMERA CIRCUIT ... C6 LENS DRIVER CIRCUIT ... C6 MAIN CIRCUIT ... C7 SYSTEM CONTROL CIRCUIT ... C8 CIRCUIT DIAGRAMS
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol-
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 POWER CIRCUIT ... C5 STROBO CIRCUIT ... C5 CAMERA CIRCUIT ... C6 LENS CIRCUIT ... C6 MAIN CIRCUIT ... C7 SYSTEM CONTROL CIRCUIT ... C8 CIRCUIT DIAGRAMS CIRCUIT
SERVICE MANUAL Digital Movie Camera VPC-C6 VPC-C6EX
FILE NO. SERVICE MANUAL Digital Movie Camera VPC-C6 (Product Code : 168 034 01) (U.S.A.) (Canada) (Korea) (Taiwan) VPC-C6EX (Product Code : 168 034 02) (China) (South America) (Russia) (Middle East) (Africa) (Hong Kong) (Australia) (General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 VPC-C6E 2
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 ASIC CIRCUIT ... C4 CAMERA CIRCUIT ... C5 LENS CIRCUIT ... C5 SYSTEM CONTROL CIRCUIT ... C6 STROBO CIRCUIT ... C7 POWER CIRCUIT ... C7 CIRCUIT DIAGRAMS MAIN &
  OUTLINE OF CIRCUIT DESCRIPTION
OUTLINE OF CIRCUIT DESCRIPTION 1-1. CCD CIRCUIT DESCRIPTION Pin 1 1. IC Configuration The CCD peripheral circuit block basically consists of the fol- lowing ICs. V IC903 (MN39830PLJ-A) CCD imager IC901 (AN20112A) V driver 6 IC905 (AD9996BBCZ) CDS, AGC, A/D converter, H driver, vertical TG 12 H 58P
VPC-E6EX VPC-E6EXW
FILE NO. SERVICE MANUAL Digital Camera VPC-E6 (Product Code : 168 026 01) (Canada) (Korea) (Taiwan) VPC-E6EX (Product Code : 168 026 02) VPC-E6EXW (Product Code : 168 026 04) (Europe) (South America) (China) (Australia) Contents (General) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
  DISASSEMBLY
DISASSEMBLY 2-1. REMOVAL OF CABINET FRONT AND CP1 BOARD 1. Three screws 1.7x510. Remove the solder. (microphone) 2. Three screws 1.7x411. Remove the solder. 3. Cabinet front 12. Three FPCs 4. Holder cover baria 13. Screw 1.7x35. Cover lens 14. Screw 1.7 x 3.5 6. FPC 15. Connector 7. Two screws 1.7
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS
CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 ASIC CIRCUIT ... C4 CAMERA CIRCUIT ... C5 LENS CIRCUIT ... C5 SYSTEM CONTROL CIRCUIT ... C6 STROBO CIRCUIT ... C7 POWER CIRCUIT ... C7 CIRCUIT DIAGRAMS MAIN &
SERVICE MANUAL Digital Camera VPC-E60 VPC-E60EX
FILE NO. SERVICE MANUAL Digital Camera VPC-E60 (Product Code : 168 054 01) (U.S.A.) (Canada) (Korea) (Taiwan) (General) VPC-E60EX (Product Code : 168 054 02) (Europe) (U.K.) (South America) (China) (Australia) Contents (Hong Kong) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Russia) 2. DISASSEMBLY ... 1
WARNING Do not use solder containing lead. Note:
WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur
SERVICE MANUAL Digital Camera VPC-J1 VPC-J1EX
FILE NO. SERVICE MANUAL Digital Camera VPC-J1 (Product Code : 126 626 01) (U.S.A) (Canada) VPC-J1EX (Product Code : 126 626 02) (Europe) (PAL General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 9 3. ELECTRICAL ADJUSTMENT ... 12 4. USB STORAGE INFORMATION REGISTRATION ... 16