Download: ELECTRICAL ADJUSTMENT Note: If the lens, CCD and board in item 2-6, it is necessary
ELECTRICAL ADJUSTMENT Note: If the lens, CCD and board in item 2-6, it is necessary to adjust again. Item 2-6 adjustments other than these 3-1. Table for Servicing Tools should be carried out in sequence. For 5 and 6, carry out adjustment after sufficient charging has taken place. Ref. No. Name Number Part code In case of carrying out adjustment item 3 and 4 after J-1 Pattern box (color viewer) 1 VJ8-0190 adjusting item 5 and 6, adjust item 3 and 4 after turing J-2 Siemens star chart 1 off the power. J-3 Calibration software 1 VJ8-0193 J-4 Chroma meter 1 VJ8-0192 3-4. Setup 1. System require...
Author:
Sean Shared: 8/19/19
Downloads: 1967 Views: 4080
Content
ELECTRICAL ADJUSTMENT Note: If the lens, CCD and board in item 2-6, it is necessary to adjust again. Item 2-6 adjustments other than these 3-1. Table for Servicing Tools should be carried out in sequence. For 5 and 6, carry out adjustment after sufficient charging has taken place. Ref. No. Name Number Part code In case of carrying out adjustment item 3 and 4 after J-1 Pattern box (color viewer) 1 VJ8-0190 adjusting item 5 and 6, adjust item 3 and 4 after turing J-2 Siemens star chart 1 off the power. J-3 Calibration software 1 VJ8-0193 J-4 Chroma meter 1 VJ8-0192 3-4. Setup 1. System requirements J-5 Spare lump 1 VJ8-0191 Windows 98 or Me or 2000 or XP IBM R -compatible PC with pentium processor Note: J-1 Pattern box (color viewer) is 100 - 110 VAC only. CD-ROM drive 3.5-inch high-density diskette drive
J-1 J-2 USB port
40 MB RAM Hard disk drive with at least 15 MB available VGA or SVGA monitor with at least 256-color display 2. Installing calibration software 1. Insert the calibration software installation diskette into your diskette drive. 2. Open the explorer.J-3 J-4 3. Copy the DscCalDI_129 folder on the floppy disk in the FD
drive to a folder on the hard disk. 3. Installing USB driver Install the USB driver with camera or connection kit for PC. 4. Pattern box (color viewer) Turn on the switch and wait for 30 minutes for aging to take place before using Color Pure. It is used after adjusting the chroma meter (VJ8-0192) adjust color temperature to 3100 ±J-5 20 K and luminosity to 900 ± 20 cd/m2. Be careful of handling
the lump and its circumference are high temperature during use and after power off for a while. 5. Computer screen during adjustment Calibration Upload LCD AWB Firmware RGB Odd RGB Even VCOMPP(LOW) Focus Image RGB Gain VCOMDC VCOMPP(HI) 3-2. Equipment UV Matrix Cal Mode 1. Oscilloscope Initialize Tint PhaseOK
2. Digital voltmeter EVF VCOCal Data H AFC TestLCD Type 3. AC adaptor OK 4. PC (IBM R -compatible PC, Pentium processor, Window Setting Language 98 or Me or 2000 or XP) USB storage Get VID Set Serial Set Video Mode 3-3. Adjustment Items and Order Set PID Set Rev. Set 1. IC501 Oscillation Frequency Adjustment 2. CCD VSUB Adjustment 3. AWB Adjustment 4. Lens Adjustment 5. CCD Defect Detect Adjustment 6. CCD Black Point Defect Detect Adjustment 7. LCD Panel Adjustment 7-1. LCD RGB Offset Adjustment 7-2. LCD Gain Adjustment – 12 –, 3-5. Connecting the camera to the computer 1. Line up the arrow on the cable connector with the notch on the camera's USB port. Insert the connector. 2. Locate a USB port on your computer. To USB port USB cable AC adaptor – 13 –, 3-6. Adjust Specifications Note: 1. When installing a new CCD, read the abbreviation described [PW1 board (Side B)] on the rear side of CCD, and write it to the board. 2. If the CCD, each board and parts replaces, it is necessary to adjust again. Adjustment method: 1. Turn on the power. (Insert the DC jack.) 2. Shorten TP301 and TP302 of SY1 board with pushing S3003 (Flash sw). CL526 3. Read the abbreviation display on the rear side of CCD. Convert these to voltages using the table below. VR501 For example, “h” → VSUB = 11.7 V 4. Adjust with VR921 so that the voltage of TP901 at VSUB becomes the displayed voltage value ± 0.1 V. VSUB abbreviation12346789AVoltage 8.9 9.1 9.3 9.5 9.7 9.9 10.1 10.3 10.5CDEfGHJKLmNote: 10.7 10.9 11.1 11.3 11.5 11.7 11.9 12.1 12.3 12.5 1. Frequency adjustment is necessary to repair in the PW1 board and replace the parts. It is carried out with LCDNPRSUVWXYZthrough screen display mode. 12.7 12.9 13.1 13.3 13.5 13.7 13.9 14.1 14.3 14.5 Preparation: 1. Carry out the frequency adjustment disconnecting cabinet 3. AWB Adjustment front, cabinet back, cabinet top and screws of holder bat- tery. Side B of PW1 board can be seen. 2. Connect FPC of cabinet back to CN303. 3. Insert the compact flash. 4. Set the main switch to the camera mode. 5. Set the selector dial to the still image shooting mode. 6. Push the power switch, and comfirm that the through screen from the CCD can be seen on the LCD. 1. IC501 Oscillation Frequency Adjustment Measuring Point CL526 Measuring Equipment Frequency counter ADJ. Location VR501 Camera ADJ. Value 496 ± 1 kHz 0~18 cm Adjustment method: Pattern box (color viewer) 1. Adjust with VR501 to 496 ± 1 kHz. 2. CCD VSUB Adjustment Preparation: [CA2 board (Side A)] POWER switch: ON Adjusting method: 1. When setting the camera in place, set it to an angle so that nothing appears in any part of the color viewer except the TP901 VR501 white section. (Do not enter any light.) 2. Double-click on the DscCalDi129. 3. Click the AWB, and click the Yes. 4. AWB adjustment value will appear on the screen. 5. Click the OK. CL136(G) – 14 –, 4. Lens Adjustment 6. CCD Black Point Defect Detect Adjustment Camera Camera 0~18 cm Siemens Pattern box star chart (color viewer) Preparation: Preparation: POWER switch: ON POWER switch: ON Adjustment condition: Adjusting method: More than A3 size siemens star chart 1. When setting the camera in place, set it to an angle so that Fluorescent light illumination with no flicker nothing appears in any part of the color viewer except the Illumination above the subject should be 400 lux ± 10 %. white section. (Do not enter any light.) Adjustment method: 2. Double-click on the DscCalDi129. 1. Set the siemens star chart 100 cm ± 3 cm so that it be- 3. Select “CCD Black” on the LCD “Test”, and click the “Yes”. comes center of the screen. 4. After the adjustment is completed, the number of defect will 2. Double-click on the DscCalDi129. appear. 3. Click the Focus, and click the Yes. 4. Lens adjustment value will appear on the screen. 7. LCD Panel Adjustment 5. Click the OK. [CA2 board (Side A)] 5. CCD Defect Detect Adjustment Preparation: POWER switch: ON (Set the camera mode.) TP901 VR501 Adjustment method: 1. Double-click on the DscCalDi129. 2. Select “CCD Defect” on the LCD “Test”, and click the “Yes”. 3. After the adjustment is completed, OK will display. 4. Click the OK. CL136(G) 7-1. LCD RGB Offset Adjustment Preparation: POWER switch: ON Adjusting method: 1. Double-click on the DscCalDi129. 2. Adjust LCD “RGB Odd” so that the amplitude of the CL136 waveform is 0.95 V ± 0.05 V. 3. Adjust LCD “RGB Even” so that the amplitude of the CL136 waveform is 4.55 V ± 0.05 V. – 15 –, 4.55 ± 0.05 V 0.95 ± 0.05 V CL136 waveform 7-2. LCD Gain Adjustment Adjusting method: 1. Adjust LCD “RGB Gain” so that the amplitude of the CL136 waveform is 1.55 V ± 0.1 Vp-p. Note: 7-1. LCD RGB Offset adjustment should always be carried out first. 1.55 V ± 0.1 Vp-p CL136 waveform – 16 –, 4. USB STORAGE INFORMATIONREGISTRATION
USB storage data is important for when the camera is con- nected to a computer via a USB connection. If there are any errors in the USB storage data, or if it has not been saved, the USB specification conditions will not be sat- isfied, so always check and save the USB storage data. Preparation: POWER switch: ON Adjustment method: 1. Connect the camera to a computer. (Refer to 3-5. Con- necting the camera to the computer on the page 13.) 2. Double-click on the DscCalDi129. 3. Click on the Get button in the USB storage window and check the USB storage data. VID: SANYO PID: VPC-MZ3 or VPC-MZ3EX Serial: Rev. : 1.00 4. Check the “Serial” in the above USB storage data. If the displayed value is different from the serial number printed on the base of the camera, enter the number on the base of the camera. Then click the Set button. 5. Next, check VID, PID and Rev. entries in the USB storage data. If any of them are different from the values in 3. above, make the changes and then click the corresponding Set button. Calibration Upload LCD AWB Firmware RGB Odd RGB Even VCOMPP(LOW) Focus Image RGB Gain VCOMDC VCOMPP(HI) UV Matrix Cal Mode Initialize Tint PhaseOK
EVF VCO Cal Data H AFC TestLCD TypeOK
Setting Language USB storage Get VID Set Serial Set Video Mode Set PID Set Rev. Set – 17 –, 5. TROUBLESHOOTING GUIDEPOWER LOSS INOPERTIVE TAKING INOPERATIVE
PUSH SHUTTER PUSH MAIN SWBUTTON
NO IC301-55, 45 NO CHECK S3001,IC301-45 (SCAN IN 6) CHECK CN303-3 (SCAN IN 5, 6) D3012, D3013, PULSE INPUT PULSE INPUT R3038, R3037 YES YES IC302-7 4.7 V LOW CN301-18, 15 LOW CHECK IC301, CHECK PW1, IC952 (BOOST 4.7 V) (P ON, P(A) ON) RB302, PW1 HIGH HIGH IC301-10 LOW SERIAL NG CHECK CHECK IC302 (VDD) COMMUNICATION IC301, CA2 HIGH OK IC301-36 LOW CHECK IC302, R3004 CHECK CA2 (RESET)HIGH
IC301-43 LOW CHECK R3003 (BAT OFF)HIGH
IC301-40 NO CHECK X3001OSCILLATION YES
IC301-37 NO CHECK X3002OSCILLATION YES
CHECK IC301NO PICTURE
CHECK CLK NO MAIN CLOCK FOR SYSTEM OPERATION OSCILLATION X1101, NO OPERATION IF ABSENT IC111, R1101 CHECK X1101 OSCILLATOR, R1101 AND IC111YES
SD CLK NG SD RAM (IC103) MOVEMENT CLOCK OSCILLATION NO READ PROGRAM FROM IC121 IF ABSENT R1103 CHECK IC102, IC103OK
IC102-62, 63 NG INCORRECT HAND SHAKING 8-BIT CPU IC301-15, 16 CHECK EACH INTERFACEOK
CHECK SOLDERING OF MEMORY PIN – 18 –]15
Similar documents

FILE NO. SERVICE MANUAL Digital Camera VPC-MZ3EX (Product Code : 126 612 01) (Europe) (PAL General) VPC-MZ3 (Product Code : 126 612 02) (U.S.A.) (Canada) VPC-MZ3GX (Product Code : 126 612 03) (General) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 10 VAR-G6U 3. ELECTRICAL ADJUS

CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS OVERALL WIRING C1 OVERALL CIRCUIT C2 CAMERA CIRCUIT C3 SYSTEM CONTROL CIRCUIT C4 LENS CIRCUIT C5 FLASH CIRCUIT POWER SUPPLY CIRCUIT CIRCUIT DIAGRAMS CP1 BOARD (CAA) CAMERA C6 CP1 BOARD (CAB) MAIN, LCD DRIVER &

WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur

CIRCUIT DIAGRAMS & PRINTED WIRING BOARDS TABLE OF CONTENTS OVERALL WIRING & BLOCK DIAGRAMS Page OVERALL WIRING ... C3 OVERALL CIRCUIT ... C4 CAMERA CIRCUIT ... C4 LENS CIRCUIT ... C5 MAIN & LCD DRIVER CIRCUIT ... C5 SYSTEM CONTROL CIRCUIT ... C6 POWER CIRCUIT ... C7 STROBO CIRCUIT ... C7 CIRCUIT DIA

WARNING Do not use solder containing lead. Note: This product has been manufactured using lead-free solder in If replacing existing solder containing lead with lead-free sol- order to help preserve the environment. der in the soldered parts of products that have been manufac- Because of this, be sur

FILE NO. SERVICE MANUAL Digital Camera VPC-S60 (Product Code : 168 049 01) (U.S.A.) (Canada) (Korea) (Taiwan) (General) VPC-S60EX (Product Code : 168 049 02) (Europe) (U.K.) (South America) (China) (Australia) Contents (Hong Kong) 1. OUTLINE OF CIRCUIT DESCRIPTION ... 3 (Russia) 2. DISASSEMBLY ... 1

FILE NO. SERVICE MANUAL Color Digital Camera VPC-SX500EX (Product Code : 126 240 04) (Europe) (PAL Genenral) VPC-SX500 (Product Code : 126 240 06) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 13 3. ELECTRICAL ADJUSTMENT ... 16 4. TROUBLESHOOTING GUIDE... 22 5

FILE NO. SERVICE MANUAL Color Digital Camera VPC-SX500EX (Product Code : 126 240 04) (Europe) (PAL Genenral) VPC-SX500 (Product Code : 126 240 06) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 13 3. ELECTRICAL ADJUSTMENT ... 16 4. TROUBLESHOOTING GUIDE... 22 5

FILE NO. SERVICE MANUAL Color Digital Camera VPC-SX560EX (Product Code : 126 279 01) (Europe) (PAL Genenral) VPC-SX560E (Product Code : 126 279 03) (U.K.) VPC-SX560 (Product Code : 126 279 02) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 13 3. ELECTRICAL ADJU

FILE NO. SERVICE MANUAL Color Digital Camera VPC-SX550EX (Product Code : 126 265 01) (Europe) (PAL Genenral) VPC-SX550 (Product Code : 126 265 02) (U.S.A.) (Canada) MODEL NAME Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 13 3. ELECTRICAL ADJUSTMENT ... 16 4. TROUBLESHOOTING GU

FILE NO. SERVICE MANUAL Color Digital Camera VPC-X360E (Product Code : 126 251 01) (U.K.) VPC-X360EX (Product Code : 126 251 02) (Europe) (PAL General) VPC-X360 (Product Code : 126 251 03) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 12 3. ELECTRICAL ADJUSTME

FILE NO. SERVICE MANUAL Color Digital Camera VPC-Z380E (Product Code : 126 252 00) (U.K.) VPC-Z380EX (Product Code : 126 252 02) (Europe) (PAL General) VPC-Z380 (Product Code : 126 252 01) (U.S.A.) (Canada) Contents 1. OUTLINE OF CIRCUIT DESCRIPTION ... 2 2. DISASSEMBLY ... 11 3. ELECTRICAL ADJUSTME

DSC-H5 SERVICE MANUAL LEVEL 2 US Model Ver. 1.1 2006. 06 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Brazilian Model Internal memory ON BOARD Hong Kong Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIA

DSC-N1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRI

DSC-H50 RMT-DSC2 Ver. 1.3 2008.09 SECTION 6 Auto-ADJ Revision History ADJUSTMENTS Link Before starting adjustments SERVICE MODE Adjusting items when replacing main parts and boards APPLICATION FOR ADJUSTMENT (SeusEX) List of service tools SERVICE MODE DATA BACKUP CAMERA SECTION ADJUSTMENTS PREPARATI

DCR-HC36/HC36E RMT-831 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2006.08 Canadian Model Revision History North European Model How to use E Model Acrobat Reader Australian Model Chinese Model Hong Kong Model Korea Model N MECHANISM (MDX-N110) Photo: DCR-HC36 Link SPECIFICATIONS DISASSEMBLY SCHEMATIC DI
![SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger](/i/37/837/2016207676-40837-100.jpg)
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.3 2005.12 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin

DSC-P1 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.0 2000. 10 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please