Download: DSC-N1 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Japanese Model Tourist Model

DSC-N1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • Precaution on Replacing the SY-138 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécuri...
Author: Sean Shared: 8/19/19
Downloads: 313 Views: 2565

Content

DSC-N1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.12 Canadian Model

Revision History AEP Model

UK Model

How to use E Model Acrobat Reader Australian Model

Hong Kong Model

Internal memory Chinese Model ON BOARD Korea Model

Japanese Model Tourist Model Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • Precaution on Replacing the SY-138 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-N1_L2 2005L0500-1 © 2005.12 9-876-908-32 Sony EMCS Co. Published by DI Technical Support Department,

SPECIFICATIONS Camera [Power, general] BC-CSG battery charger

[System] Power Rechargeable battery pack NP- Power requirements BG1, 3.6 V AC 100 to 240 V, 50/60 Hz, Image device 9.10 mm (1/1.8 type) color CCD, Primary color filter AC-LS5K AC Adaptor (not2Wsupplied), 4.2 V Output voltage DC 4.2 V, 0.25 A Total pixel number of camera Approx. 8 303 000 pixels Power consumption (during shooting) Operating temperature 1.3 W 0°C to +40°C (+32°F to Effective pixel number of camera Approx. 8 068 000 pixels Operating temperature +104°F) 0°C to +40°C (+32°F to Storage temperature Lens Carl Zeiss Vario-Tessar +104°F) −20°C to +60°C (−4°F to 3× zoom lens f = 7.9 − 23.7 mm (38 − Storage temperature +140°F) 114 mm when converted to a −20°C to +60°C (−4°F to Dimensions Approx. 62 × 24 × 91 mm 35 mm still camera) +140°F) (2 1/2 × 31/32 × 3 5/8 inches) F2.8 − 5.4 Dimensions 96.7 × 61.1 × 22.7 mm (W/H/D) Exposure control Automatic exposure, Manual (3 7/8 × 2 1/2 × 29/32 inches) Mass Approx. 75 g (2.7 oz) exposure, Scene Selection (8 (W/H/D, excluding protrusions) modes) Mass Approx. 185 g (6.5 oz) Rechargeable battery pack NP-BG1 White balance Automatic, Daylight, Cloudy, (including NP-BG1 battery Used battery Lithium-ion battery Fluorescent, Incandescent, pack, wrist strap, stylus, etc.) Flash Microphone Electret condenser microphone Maximum voltage DC 4.2 V File format (DCF compliant) Speaker Dynamic speaker Still images: Exif Ver. 2.2 Nominal voltage DC 3.6 V JPEG compliant, DPOF Exif Print Compatible Capacity 3.6 Wh (960 mAh) compatible PRINT Image Matching III Movies: MPEG1 compliant Compatible Design and specifications are subject to change (Monaural) PictBridge Compatible without notice. Recording media Internal Memory (26 MB) “Memory Stick Duo” Flash Recommended distance (ISO set to Auto): approx. 0.20 m to 5.0 m (7 7/8 inches to 8 feet 6 3/8 inches) (W)/approx. 0.34 m to 2.6 m (1 feet 1 1/2 inches to 16 feet 4 7/8 inches) (T) [Input and Output connectors] Multi connector USB communication Hi-Speed USB (USB 2.0 compliant) [LCD screen] LCD panel 7.5 cm (3 type) TFT drive Total number of dots 230 400 (960×240) dots — 2 —,

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. FLEXIBLE Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page Section Title Page 1. SERVICE NOTE 1-1. Description on Self-diagnosis Display ···························· 1-1 1-2. Process After Fixing Flash Error ····································· 1-1 1-3. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-2 1-4. Precaution on Replacing the SY-138 Board ···················· 1-3 2. DISASSEMBLY 2-1. Disassembly ····································································· 2-3 2-2. The Method of Attachment of Cabinet Center Block ······ 2-5 2-3. Exchange Method of Barrier Assembly ·························· 2-7 2-4. Exchange Method of LSV-1100A ································· 2-10 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-3 3-3. Power Block Diagram ····················································· 3-5 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-5 4-3. Printed Wiring Boards ··················································· 4-31 5. REPAIR PARTS LIST 5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-7 — 4 —, 1. SERVICE NOTE 1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory Stick” or internal “Memory Stick” or internal memory is FORMAT ERROR memory. unformatted. C:13:ss Insert a new “Memory Stick”. “Memory Stick” is broken. MEMORY STICK ERROR Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. (Note) charged. Note: After repair, be sure to perfom “1-2. PROCESS AFTER FIXING FLASH ERROR”. 1-2. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen. Method for Initializing the Flash Error Code Initialize Initializes the setting to the default setting. The message “Initialize all settings Ready?” appears. OK Resets the settings to the default setting. Cancel Cancels the resetting. • Make sure that the power is not disconnected during resetting. 1-1, 1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY (INTERNAL MEMORY/ALBUM/MUSIC)

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-138 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-138 board or the IC401 on the SY-138 board, execute formatting and initialize the internal memory after

replacement.

Method for Copying the Data in Internal Memory or Album

Copy Copies all images in the internal memory or the Album to a “Memory Stick Duo”. Internal Memory Copies the image files in the internal memory. Album Copies the image files in the Album. 1 Insert a “Memory Stick Duo” having 32 MB or larger capacity. 2 Touch media ([Internal Memory] or [Album]) you want to copy the image files from. The message “All data in internal memory will be copied (All data in Album will be copied) Ready?” appears. 3 Touch [OK]. Copying starts. Copying 102_COPY • Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. • You cannot copy individual images. • The original images in the internal memory or Album are retained even after copying. To delete the contents of the internal memory or Album, execute the [Format] command in (Internal Memory) or (Album). • You cannot select a folder to be copied on a “Memory Stick Duo”. • Even if you copy data, a (Print order) mark is not copied. • When copying from the Album, the image protection setting is not copied. • When playing back images in the Album, the order of images displayed on the screen may be different from that of images copied on the “Memory Stick Duo”.

Method for Formatting the Internal Memory

Format Formats the internal memory. • Note that formatting irrevocably erases all data in the internal memory, including even protected images. The message “All data in internal memory will be erased Ready?” appears. OK Formats the internal memory. Cancel Cancels the formatting.

Method for Formatting the Album

Format Formats the Album. • Note that formatting irrevocably erases all data in the Album, including even protected images. The message “All data in Album will be erased Ready?” appears. OK Formats the Album. Cancel Cancels the formatting. 1-2,

Method for Formatting the Music

Format Music If you cannot play back a Music file for the Slide Show, the Music file might be corrupted. If this happens, perform [Format Music], then transfer the music by [Download Music] using the supplied “Music Transfer” software. • If you format the write-in-area of the Music file, all Music files are deleted and cannot be restored. The message “All data will be erased Ready?” appears. OK Formats the Music files. All data other than Music files remain as it is. Cancel Cancels the formatting. 1-3, 1-4. PRECAUTION ON REPLACING THE SY-138 BOARD VIDEO OUT Default Data Check When you replace to the repairing board, the written data of repairing board also might be changed to original setteing because of broadcast system (NTSC/PAL). When the data has changed because of board replaceing etc, check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Data Page Address NTSC PAL 4F 89 00 01 4F A2 00 01 Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 89, and set data: 00 (NTSC) or data: 01 (PAL). 3) Select page: 4F, address: A2, and set data: 00 (NTSC) or data: 01 (PAL). 4) Select page: 40, address: 38, and set data: 00. 5) Click [Save] on the SEUS screen. 6) Select page: 80, address: 34, and check that the data is “00”. 7) Select page: 80, address: 30, and check that the data is “00”. 8) Select page: 00, address: 01, and set data: 00. Initial Language Data Check If the SY-138 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data Language GP1 GP2 GP3 GP4 00 Englishzzz01 Japanese z 04 Spanishzz4F 88 08 Simplified Chinese z 0B Russian z 0D Korean z Note: GP1 is fixed to Japanese. GP2 is fixed to English. GP3 is either English, Spanish or Russian. GP4 is either English, Spanish, Simplified Chinese or Korean. Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 88, and set the Initial Language Data. 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is “00”. 6) Select page: 80, address: 30, and check that the data is “00”. 7) Select page: 00, address: 01, and set data: 00. 8) Turn off the camera. 9) Turn on the camera. Execute “Initialize” of Setup screen. 10) Check the language displayed when the camera starts. 1-4E, 2. DISASSEMBLY Link

DISASSEMBLY

THE METHOD OF ATTACHMENT OF CABINET CENTER BLOCK EXCHANGE METHOD OF BARRIER ASSEMBLY EXCHANGE METHOD OF LSV-1100A

HELP

, 2. DISASSEMBLY 2. DISSASSEMBLY

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some • When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside) • When installing a connector, dont’ press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE ST-129 FLEXIBLE BOARD’S CHARGING CAPACITOR (C901)

The charging capacitor (C901) of the ST-129 FLEXIBLE board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.

Preparing the Short Jig Note: High-voltage cautions

To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Discharging the Capacitor Wrap insulating tape fully around the leads of the resistor to Short-circuit between the two points prevent electrical shock. with the short jig about 10 seconds. 1 kΩ/1 W Wrap insulating tape. R:1 kΩ/1 W (Part code: 1-215-869-11) 2-1, 2. DISASSEMBLY HELP The following flow chart shows the disassembly procedure. 2-1. DISASSEMBLY36551P2 screw (M1.4x2.5) (silver) x5 1 Insert the flat blade 2 Claw x2 1 screw driver. 2 3 Cabinet (front) block 2 Claw x1 4 Flexible board x2 3 Claw x2 5 Flexible board x114Multi cap 6 Lens block 5 Flexible board x2 6 P2 tapping screw (M1.4x3) (silver) x1 7 Remove the SY-MC board. 1 8 Flexible board x2 9 SY-MC board. 1 Flexible board x1 2 Claw x363Microphone holder 4 Screw (M1.4x3) (silver) x5145Cabinet (rear) block 2HELP871Rotate the ornamental ring (A), 3 4 and release the bond. 1 2 Ornamental ring (A) 5 3 Insert the tweezers etc.. 4 Claew x3545Barrier block assembly21Claw x1 7 Claw x1 Note: When you exchange Position of claws 2 Claw x2 8 ST board barrier block assembly 3 Remove the ST board. and ornamental ring (A), be sure44Claw x3 Refer to page 2-1 to follow the procedure carried on 5 Holder (AF) " Discharging of the ST-129 flexible board's "2-3. Exchange Method of Barrier 6 Discharging the Capacitor. charging capacitor (C901) ", Assembly" (2-7 page). when discharging the capacitor. 2-3 2-4, 2. DISASSEMBLY 2-2. THE METHOD OF ATTACHMENT OF CABINET CENTER BLOCK 1 Spring (lock claw) x1 3 BT cover x1 4 MS guide light x1 2 Lock claw (BT) x1 Slide until the hook of the BT cover Cabinet (center) block reaches the boss of the cabinet. boss hook 5 Slide the BT cover at the bottom. Check it the BT cover is locked and not removed. Spring (lock claw) MS guide light BT cover Lock claw (BT) BT cover 2-5 2-6, 2. DISASSEMBLY 2-3. EXCHANGE METHOD OF BARRIER ASSEMBLY 2-3-1. PEEL OFF OLD ORNAMENTAL RING (A) Turn on the power, and set the zoom to the TELE end. Remove the battery forcibly. Turn the ornamental ring (A) clockwise to remove. * Discard the removed ornamental ring (A). Ornamental ring (A) 2-3-2. REMOVE OLD BARRIER BLOCK ASSEMBLY Inert tweezers, etc. into a slit in the lens, and pry the barrier block assembly with the fulcrum at a hole in the 1 group frame. * Discard the removed barrier block assembly. Barrier block Claw assembly Claw Slit 1 group frame DSC-N1_L2 2-7, 2. DISASSEMBLY 2-3-3. INSTALL NEW BARRIER BLOCK ASSEMBLY Put the battery in the camera, and turn on the power (press twice to retract the lens-barrel). Meeting the part A with the part a, B with b, and C with c respectively, mount a new barrier block assembly on the lens (fit it completely, avoiding loose engagement or floating). B b

A

CcaNote: Check that the diaphragm of the barrier block assembly is not opened slightly or half-closed. DSC-N1_L2 2-8, 2. DISASSEMBLY 2-3-4. INSTALL NEW ORNAMENTAL RING (A) Apply a thin coat of adhesive to the inside of ornamental ring (A). Note: Use adhesive (Super X) or an equivalent article. Don’t use what becomes white after drying like a quick-drying glue. Position of adhesive spreading Note: Refer after the adhesive of the removed ring. Wipe off when the adhesive adheres outside or edge side on the ring. Adhesive 0.1mm 0.5mm 1.5-2.0mm Adhesive Ornamental ring (A) Ornamental ring (A) From the top spring position, cover new ornamental ring (A) on the 1 group frame. Rotate the ornamental ring (A) over 90 degrees to spread the adhesive. Note: Adhesive must not run off the lens-barrel. Stiffen by leaving it for 60 minutes or more. Ornamental ring (A) Spring Turn on and off the power to check the opening and closing of the barrier block with the camera in horizontal, up and down directions respectively. Further, check the zoom motion. Rotate the ornamental ring (A) lightly to check that it is not removed. DSC-N1_L2 2-9, 2. DISASSEMBLY 2-4. EXCHANGE METHOD OF LSV-1100A 2-4-1. REMOVE THE ZOOM GEAR BLOCK Preparation: Detach the lens after turning on the set power supply, and moving the position of the zoom to “x2.0”. (Detach under such a condition it when the zoom does not move.) Tweezers etc. 5708qa1Splate spring x1 * 2 F plate spring x1 * 3 3 group spring x14Zplate spring x1 * Tweezers etc. 5 Remove the reset sensor. 6 Flexxible board x1 7 Screw (1.2x4) (red) x4 8 Back body block Note: Be careful to the focus motor flexible board. Do not make the lens dirty by touching. 9 Naruto washer * 0 Naruto gear * qa Zoom gear block * Discard the removed parts. DSC-N1_L2 2-10, 2. DISASSEMBLY 2-4-2. ASSEMBLY OF ZOOM GEAR BLOCK AND FRONT LENS BLOCK 1 Install the new zoom gear block. Zoom gear block Check positions Zoom flexible board Boss Boss 2 Install the new naruto gear and new naruto washer. Naruto washer Naruto gear Note: Turn the difference part a little and set the naruto gear when the naruto gear is floating. Check the shape Naruto gear Rear side Difference part Front side DSC-N1_L2 2-11, 2. DISASSEMBLY 3 Put the back body block on the front lens block, taking care of the following points: Note: 1 Do not pinch the 3 group spring and Z reset sensor by the set. 2 Do not allow the naruto washer and naruto gear to drop off. 3 The flexible cable must be engaged with the ribs of the back body block. 4 Do not touch the flexible board etc. to G6 lens. G6 lens 3 group spring Flexible cable Z reset sensor Check the state of the flexible board Confirm whether flexible board hangs in Naruto gear, the rib of the back body block. Naruto washer Confirm the flexible board has gone out up. Confirm abnormality is not found in the state of the flexible board. 4 Tighten four screws in the order of A to D. * Tightening torque = 0.5 kgf • cm (4.9 N)

B C A D

DSC-N1_L2 2-12, 2. DISASSEMBLY 5 Insert the flexible cable (beware of loose insertion). Flexible board 6 Install the Z reset sensor (press fitting into zoom gear block). Z reset sensor DSC-N1_L2 2-13, 2. DISASSEMBLY 2-4-3. INSTALL NEW Z PLATE SPRING Z plate spring 1 Hook a claw of the Z plate spring on the zoom gear block. 2 Pressing the spring in the arrow direction, engage the part of the Z plate spring in position shown above. 3 Pressing the spring in the arrow direction, engage two claws of the Z plate spring. DSC-N1_L2 2-14, 2. DISASSEMBLY 2-4-4. INSTALL NEW 3 GROUP SPRING Hook the 3 group spring on the front lens block by using the tweezers, etc. Hook 3 group spring (Non-replaceable part. Beware of damage.) Tweezers etc. 2-4-5. INSTALL NEW F PLATE SPRING Hold the reset P1 sensor with the F plate spring to secure. 1 Hook two claws of the F plate spring on the zoom gear block. 2 Engage two claws of the zoom gear block and F plate spring. P1 reset sensor F plate spring DSC-N1_L2 2-15, 2. DISASSEMBLY 2-4-6. INSTALL NEW S PLATE SPRING Check that the flexible cable is secured with four bosses of the front lens block as shown above. Flexible cable Boss 1 Boss S plate spring 1 Insert the claw of the S plate spring into a hole in the front lens block. 2 Engage the S plate spring with the claw of the front lens block. 2-4-7. CHECK THE OPERATION Confirm the operation after installing the lens in the set. 1. Power ON/OFF 2. Expansion and contraction confirming of lens and opening and shutting confirmation of barrier. Confirm there are neither dirt nor wounds in the surface of the ornamental ring (A) and lens if there is no problem in operation. Wipe off when dirty. 3. Confirm the operation with Wide/Tele.s Note: Do not be of caught etc. Do not allophone. DSC-N1_L2 2-16E,

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. 1 Pass the BT discharge 2 Route the BT discharge spring spring through a hole in front of the holder (spring) in the holder (spring). and hook it onto the plate as shown below. BT discharge spring holder (spring) SW-460 flexible board SW-460 flexible board Claw (Retainer plate (LCD)) Mode knob S005 Claw (Retainer plate (LCD)) Cabinet (rear) assembly

HELP

, SP-046 flexible board RL-062 flexible board Adhesive sheet (including SP Claw flexible board) Cabinet (senter) section Cabinet (rear) section

HELP

, CCD block CCD block CD-585 Sheet (CD)

HELP

, 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM OVERALL BLOCK DIAGRAM (2/2), 3. BLOCK DIAGRAMS

Ver 1.1 2005.11

3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

CD-585 FLEXIBLE BOARD SY-138 BOARD (1/2)

LENS BLOCK PANEL UNIT LENS IRIS (METER) CN101 CN714 IC002 171312 CCD_OUT H10 CA_AD0 – CA_AD13 LCD_D0 - LCD_D7 D0 - D7 BUFFER LCD901 19 LCD_HD, LCD_VD IC801 HD, VDIC001 3INCH CCD A2 CA_HD E20 LCD_CK CHARACTORQ002 POWER_SAVE IC101 DCK

COLOR

IMAGER 6 F7 H23 E1 GENERATOR A5 20 LCD UNITXCS_ IC_801 (5/8) SHUTTER ZOOM FOCUS IRIS CCD SIGNAL W8 B1 MOTOR MOTOR MOTOR MOTOR H1A, H2A, H1B, H2B PROCESS, CA_FD A3 B18 SYS_VDB13 G1

TIMING MMMMGENERATOR J21 F1 TOUCH_PANEL_YU

RG (1/8) TOUCH_PANEL_XL

OVERALL

23 4 K4 IC301 D1, C1 TOUCH TOUCH_PANEL_YL (2/2) (1/2) PANEL 1 XCS_ PANEL XCS TOUCH_PANEL_XR (PAGE 3-3)V1, V2, V3A, V3B, V4, W9 11 ZOOM FOCUS V5A, V5B, V6 - V10 CAMERA DSP, CPU LCD_ADJ1 4.2VADJ SENSOR RESET A4 CLKTGO B23 LENS CONTROL, Y17 27 1, 2 SENSOR B17 MODE CONTROL XIC_301 (2/8) _RST_OUT RESET VHLD8527 D5 C2 XCS_FE AB7

VST

3 25 D6 IC_301_1_SO, XIC_301_1_SCK SI, SCLK 26 2 VSUB C4 VSUB_CONT IC_301_1_SO, XIC_301_1_SCK 27 1 Q101 E7 C1 XIC_301_RST_OUT D901

BACKLIGHT

BL_H OVERALL VSUB_CONT_PRE, 2 (2/2) Q102 VSUB_CONT_POST BL_L (PAGE 3-3) IC201 XCAM_DR_PS D4 W12 XIC_301_RST_OUTLENS DRIVE E9 (3/8) CN201 IRIS_S_IN, IRIS_S_EN, MS_BS, MS_D0 – MS_D3, MS_CLK IRIS_S_+, S_–, M_+, M_– IRIS_S_+, S_–, M_+, M_– IRIS MOTOR IRIS_M_IN, IRIS_M_EN

DRIVER

IC651 FC_DIR_A, IC_301_VOUTAC19 3 V_LINE_OUTVIDEO AMP 5 F_MOTOR A, A, B, B FOCUS_A, A, B, B FOCUS FC_DIR_B, AB10 VIDEO_AMP_ON 4 (6/8) MOTOR FC_BRK_A DRIVER OVERALL (2/2) IC_301_1_SO, XIC_301_1_SCK IC_301_1_SO, XIC_301_1_SCK 3 (PAGE 3-3) ZM_DIR_A, ZM_BRK_A, AC15 IC_301_AUOUT Z_DC_MOTOR (+), (–) ZOOM_DC_+, DC_– ZOOM ZM_BRK_B IC_301_AUIN MOTOR AC17

DRIVER

Y8 XCS_AUDIO MSHUT_DIR, USB_D+, USB_D– SHUTTER_+, – SHUTTER_+, – SHUTTER MSHUT_EN

MOTOR

DRIVER XIC_301_RST_OUT F_PI_SENS_OUT, C10 XFC_RST_LED FC_SENS, XFC_RST_LED Q305 USB_VBUS Z_BOX2_PI_SENS_COL, Z_BOX1_PI_SENS_COL, ZM_DC_FG_1A, ZM_DC_FG_1B, XZM_FG_LED, Z_PI_SENS_OUT XZM_FG_LED, ZM_SENS_1ST LENS TEMP LENS_TMP Y14 XIC_301_RST_OUT SENSOR 21 B4 H1, F4, K3, J3, L11, K10, K12, J11, J2, J4, K4, K5, CPU_D00 – CPU_D15 E11, D12, D10, C10,G4, H2, H3, K2, L12, K11, J10, J12, H4, G2, J5, E6 E10, D11, D9, C9

ST-129 FLEXIBLE BOARD

T001 CPU_A20, CPU_A21 XE_A (H) D00162ST_UNREG C901 1 CHARGING + IC401 TRIGGER CAPACITOR54256M SDRAM,FLASH UNIT TRIGGER_GND CN708 SUPER AND FLASH (64M) 15 10 6 STRB_CHG W11 (4/8)IC00195XSTRB_FULL AC9 Y22, U19, AB23, V20, AB22, W21, F9, E9, D8, C8, F8, E8, FLASH Y21, W22, AA22, AB21, AC22, AA21, D7, C7, F4, E5, D6, C6, XE_K (L) CONTROL, Y20, AA20, V19, W20, J22, H20,K20, H19, L21, J20, K21, J19, K22, DSP_DQ00 – DSP_DQ31, DSP_DQM0 – DSP_DQM3 F3, E4, D5, C5, M10, L10, CHARGE K9, J9, M9, L9, K8, J8, Q001 STRB_ON K19, M22, L19, L20, M20, L22, M5, L5, K4, J4, M4, L4,CONTROL FLASH743E12 M19, N22, M21, P22, N21 K3, J3, F7, F5, J7, J564STRB_CHG_CONTDRIVE W4 P20, T22, R21, U22, P19, H9, G10, H10, G9, R19, R20, U21, T19, V21, DSP_AQ00 – DSP_AQ11, DSP_QBA0, DSP_QBA1 G2 - G5, H2, H3, T21, V22, AA23, U20 H8, H4, J6, F6 T23 DSP_QCLK N7 D002

A : VIDEO SIGNAL SELF TIMER/ XAF_LED XAF_LED1 4 OVERALL (2/2) A : AUDIO SIGNAL AF ILLUMINATOR (PAGE 3-4) A : VIDEO/AUDIO SIGNAL 05

3-1 3-2 1, 4, 6 - 15 28, 29, 25, 24 26, 22, 24, 18 7, 8 15 - 12 28 - 31 1 - 4 11, 10, 16, 17 24, 26, 28 - 37 21, 22, 19, 18 1, 2 F4, F3 B4, B5 D6, E6, B7, C6 F2, E2, D2, B1 G7, H6, G6, G5, K6, K5, J6, J5 H5, H4, G4, F4, E4, D7, H7, D4 D1, E3 - E1, F3 - F1, G3 - G1, G1, E4 A2, C4, B2 D5, A6, B6, C5 F5, D3, G6, E3 B3, C3 H3 - H1, J1 B8, E11, B10, E22 AC12, C12 A12, B12, E14 A13, E15, D15 C13, E13, AB12, C11 C19, D18, B16, E19, A17, D20, E10 D13, C14 C18, C15, D17, B15, E18, C16, C17, B14, D16 G19, J23, F19, E3, D3, E2, F20, G21, G22, L2, H5 A5, A4 D11, D12 F3, D2, E1 H21, H20 F22, H22 J1, H1 J2 - J9 H9, G9, F9, E9, A8, A7 D9, C9, B9, A9 M3, E3 10, 9 21, 22 12 - 19,

Ver 1.1 2005.11

3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-138 BOARD (2/2) MS-292 FLEXIBLE BOARD

CN715 CN001 MS_BS, MS_D0 – MS_D3, MS_CLK MS_BS, MS_D0 – MS_D3, MS_CLK SDIO/DATA0, DATA1 - DATA3, SCLK MEMORY

STICK DUO

XMS_IN 15 INT 6 V_LINE_OUT CHARGE_V BATT_UNREG + BATT_SIG BATT_SIG BT9015SBATTERY BATT_GND TERMINAL – IC301_1_SO, XIC_301_1_SCK IC602

OVERALL (1/2) AUDIO AMP D1

(PAGE 3-2) 3 (6/8)IC_301_AUOUT E5 CN716 IC_301_AUIN B6 FP-316 FLEXIBLE MC-158 BOARD E6 BOARD XCS_AUDIO (MAGIC FLEXIBLE) W952 E4 V_LINE_OUT 16 28 V_OUT 20 AU_LINE_OUT 13 31 A_OUT_L 16 USB_D+, USB_D– USB_D+, USB_D– USB_D+, USB_D– USB_VBUS USB_VBUS USB_VBUS 17 26 6 XIC_301_RST_OUT AA9 XAV_JACK_IN XAV_JACK_IN XAV_JACK_IN

SP-046 RL-062 28 16 26

CRADLE_AD1, CRADLE_AD2 CRADLE_AD1,FLEXIBLE FLEXIBLE CRADLE_AD1, CRADLE_AD2 CRADLE_AD2

BOARD BOARD

XSTATION_IN XSTATION_IN XSTATION_IN CN002 CN710 W10 7 37 2 SP901 SP+, SP– SP+, SP– XACV_IN XACV_IN BATT/XEXT BATT_XEXTAB9 27 18 19

SPEAKER

IC303 (2/2) MIC_SIG MIC_SIG IC301 MIC901 3 17 (2/2) (2/8) Q304 CN951 FRONT CONTROL IC_301_TXD434MULTIW6 BATTERY (2/8) BATT_SIG

CONNECTOR

S002 CHARGE (SHUTTER) IC_301_RXD4AC6 DETECT C9 B10 25 XAE LOCK_SW AB13 XSHUTTER_SW IC303 (1/2) 23 Y12 X302 EVER_2.9V (2/8) 12MHz VL_3V61B8 BT001 Q705, 706 C23 MS_VCC H1 LITHIUM D001, D004 XPWR_LED_K 19 LED

BATTERY

(POWER) DRIVE Y19 2 D_3.2V A_3.2V 3 IC302 CAM_2.9V ST_UNREGIC001 BATTERY ACV_UNREG ACV_UNREG D302 D_1.8V

SW-460 AUTHENTICATE(ACCESS LED) D21 M_5V DC/DC FLEXIBLE (2/8) D_1.2V CONVERTER(7/8) BOARD 6 - 8 1 A9PANEL_8.5V Q001, 002X001

32.768kHz S005 A8 CN001 CHARGE_V CHARGE_VIC606 MODE MODE_DIAL0 A_3.2VA_2.9V SELECT68AB14 2.9V REG XPWR_ON 9 36 XPOWER_ON 7 (6/8) S001 - 004 FUNCTION KEY_AD0 KEY85AA13 CAM_15V IC002 VCC CAM_–7.5V 15V/–7.5V REG CN001 (7/8) TOUCH_PANEL_YU TOUCH_PANEL_X

OVERALL1113 AB15TOUCH_PANEL_XL TOUCH_PANEL_Y –7.5V_ON

(1/2) 15410 Y15TOUCH_PANEL_YL AB11 (PAGE 3-2) 2 2 12TOUCH_PANEL_XR4 3 11 AA16 BATT_SENS G5 TOUCH_PANEL_SEL1 Y11 MS_PWR_ON D3 TOUCH N4 PANEL ON/OFF TOUCH_PANEL_SEL2 Y9 XCS_DD K1 A6 Q701 - 703 CN002 IC_301_0_SI, IC_301_0_SO, XIC_301_0_SCK

OVERALL BL_H BL_H10 3 Y10 XDD_RST_OUT A7

(1/2) 2 B7BL_L BL_L (PAGE 3-2) 12 1 AC7 XPWR_OFF B7 BL_H A4 XAF_LEDE9 OVERALL (1/2) BL_L F9 (PAGE 3-2) S001 POWER 18 XPWR_ON XPOWER_ON C7

A : VIDEO SIGNAL A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL

3-3 3-4 5, 6 1, 2 5, 6 F3, E3 15, 14 A5, A2 D8, D7, C5 AA15, W16 C6, C5, B6 USB_VBUS XMS_IN 33 - 29 34 - 37 12, 10 20, 23 1 - 4 6 - 9 19-16, 14, 13 11 -15 7 - 10 33, 34 23, 20 2 - 5, 7, 8 17, 21 23, 25 15, 9 10, 12,

Ver 1.1 2005.11

3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

MC-158 SY-138 BOARD ST-129 FLEXIBLE BOARD BOARD CN716FP-316 FLEXIBLE

T002 W952 BOARD CN708 ACV_UNREG (MAGIC FLEXIBLE) ACV_UNREG F001 ST_UNREG ST_UNREG L001 D001 FLASH

UNIT UNREG

M_5V Q001,002 F002 7 BATT_XEXT BATT/XEXT 19 18 27 D_3.2V CN951 2 D002 IC001 MULTI D004 D003 IC001 SELF TIMER/ FLASH CONTROL, CONNECTOR DC/DC CONVERTER AF ILLUMINATOR CHARGE CONTROL (7/8) CHARGE_V CHARGE_V XPWRON1 C7 D715 RL-062 D004, 005 XCHG_ON XCHG_ON A_3.2V L005 F003 24 17 26 FLEXIBLE BOARD (KEY ILLUMINATION) XPOWER_ON XPWR_ON LX3 E10 CN710 PANEL UNIT CN001 7 36 9 M_5V D00695D901 J1 UNREG1-1 CN002 BACKLIGHT K1 UNREG1-2 BL_H BL_H BL_HVO3 E9 3 10 J6 UNREG2-1 K6 UNREG2-2 BL_L BL_L BL_L VL3 F9 1 12 S001 A1 PWR1-1 VO1-1 F1 D_3.2V XPWR_ON 18 POWER SW-460 B1 PWR1-2 VO1-2 F2 IC606 FLEXIBLE BOARD C2 PWR1-3 PWR_LED_A D001, 004VFB1 H2 2.9V REG 21 (POWER) D10 PWR2 (6/8) L003 A_2.9V 4 VIN VOUT 3 LCD901 B8 RTCBAT CN714 PANEL_8.5V L703 PVDD D005 VO7 K4 5 3INCH COLORL702 VCC2 LCD UNITH1 LDO1 28 L701 VCC1 With TOUCH A_3.2V 29 PANEL LDO2IN B3 BT001 A3 D_1.8V IC602LDO2 LITHIUM AUDIO AMP IC801 BATTERY (6/8) CARACTOR LDO3IN B2 VL_3V GENERATORCAM_2.9V (5/8) LDO3 A2 LENS BLOCK CN201 L002 D_1.2V Z_BOX1_PI_SENS_VCC23

MS-292 LX2 C10 Z_BOX2_PI_SENS_VCC ZOOM FLEXIBLE 25 RESETZ_PI_SENS_VCC BOARD VFB2 D8 SWITCHING 19 SENSOR

CN001 CN715 MEMORY VCC MS_VCC MS_VCC L009 Q201 STICK 9 12 G2 MS_PWR MS_PWR_IN G1 Q004, 005 FOCUS DUO L006D3 MS_PWR_ON M_5V F_PI_SENS_VCC SWITCHING 6 RESETIC201 Q003 SENSOR BG4 G9 DC CONTROL LENS DRIVE (3/8) TG4 F10 PSG4 G8 EVER_2.9V VFB4 F7 D_3.2V L102 L104 MS_PWR_ON XACV_IN Y11 FB103 AB9 VREF G6 IC101IC002 VFB6 H7 CCD SIGNAL GT6 H6 15V/–7.5V REG CAM_2.9V L103 PROCESS, + BATT_UNREG BATT_SENS AA16 G5 UNREGMON (7/8) TIMING IC301 L007IC_301_0_SI, IC_301_0_SO, CAM_–7.5V FB101 CAM_–7.5V GENERATOR PWR56OUT1 J7 SWITCHING 3 VEE REG3 4XIC_301_0_SCK (1/8) CAMERA SO PWR56OUT2 K7 FB102 DSP, SI Q006 CAM_15V CAM_15V Q304 CPU, SCLK LX5-1 J9 BT901 XCS_DD BATTERY LENS Y9 A6 CE LX5-2 J10BATTERY BATT_SIG AC6 XDD_RST_OUT 7 VCC REG2 6 TERMINALS5CHARGE CONTROL, Y10 A7 XRESET LX5-3 K9 D007 DETECT MODE XPWR_OFF STB CONTROL, AC7 B7 XPWROFF LX5-4 K10 IC303 1FONT CD-585 FLEXIBLE BOARDIC401 (2/8) CONTROL VFB5 H9 L101 CN101 (2/8) 256M SDRAM, CAM_15V8 BATT_GND43W6 –7.5V_ON SUPER AND IC001 – AB11 L401 FLASH (64M) FB104 (4/8) CAM_–8V39 CCD IMAGER D_1.2V D_1.2V L302 D_1.8V D_1.8V IC651 IC002 VIDEO AMP A_3.2V A_3.2V BUFFER(6/8) A_2.9V L351 A_2.9V D_3.2V D_3.2V L301 IC302

BATTERY AUTHENTICATE

(2/8) XZM_RST_LED C21 3-5 3-6E 17, 21 23, 25 1-4 6-9 11-15 7-10 D_3.2V 29-33 34-37 XACV_IN D8, D7, C5 C6, C5, B6 12-14 D_3.2V 5, 6 1, 2, 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM

FRAME SCHEMATIC DIAGRAM

CN201 31P Z_DC_MOTOR(-) 31

ST-129 Z_DC_MOTOR(-) 30Z_DC_MOTOR(+) 29 FLEXIBLE Z_DC_MOTOR(+) 28REG_GND(GUARD) 27 BOARD Z_BOX2_PI_SENS_Col 26C901 FLASH UNIT105u Z_BOX2_PI_SENS_Vcc 25

315V

CHARGING

CAPACITOR (FLASH DRIVE) XZM_FG_LED 24 Z_BOX1_PI_SENS_Vcc 23 Z_BOX1_PI_SENS_Col 22 LENS TEMP 21 CCD GND(Th+Z_PI) 20 Z_PI_SENS_VCC 19 IMAGER Z_PI_SENS_OUT 18 IRIS_M_- 17 CN710 25P IRIS_M_+ 16 1 BL_L CN002 6P SHUTTER_(+) 15 2 NC 6 SP- SHUTTER_(+) 14 MIC901 3 BL_H

SP-046 5 SP+ SHUTTER_(-) 134 NC FLEXIBLE 4 MIC_GND SHUTTER_(-) 125 KEY_AD0

3 MIC_SIG IRIS_S_+ 11 LENS

BOARD 6 NC

SP901 2 NC IRIS_S_- 10 SPEAKER 7 REG_GND1 NC REG_GND(GUARD) 9 BLOCK 8 MODE_DIAL0 XFC_RST_LED89M_5V

RL-062 F_PI_SENS_OUT 710 TOUCH_PANEL_XL F_PI_SENS_VCC 6

11 TOUCH_PANEL_XR

FLEXIBLE REG_GND(GUARD) 512 TOUCH_PANEL_YL F_MOTOR A 4

13 TOUCH_PANEL_YU

BOARD F_MOTOR B 314 SP- F_MOTOR A 2

15 SP+ F_MOTORB1(CONTROL SWITCH) 16 MIC_GND 17 MIC_SIG CN101 39P 18 XPWR_ON CAM_-8V 39 19 PWR_LED_K 20 NC SY-138 BOARD N.C. 38V10 37 21 PWR_LED_A V9 36 22 REG_GND (1/8) (CCD SIGNAL PROCESS) V8 35 23 XSHUTTER_SW (2/8) (CAMERA DSP) V7 34 24 NC V6 33 25 XAE_LOCK_SW (3/8) (LENS DRIVE) V5B 32 (4/8) (SDRAM, SUPER AND) V5A 31 V4 30 (5/8) (CHARACTER GENERATOR) V3B 29 (6/8) (AUDIO, VIDEO) V3A 28 VHLD 27 (7/8) (DC/DC CONVERTER) V2 26

SW-460 (8/8) (CONNECTOR) VST 25

V1 24

FLEXIBLE CD-585GND 23

H2A 22

BOARD FLEXIBLEH1A 21

GND 20 BOARD (CONTROL SWITCH) H1B 19 CN714 31P H2B 18 (CCD IMAGER) 1 NC GND 17 2 NC GND 16 3 COM GND 15 4 GND CCD_GND 14 5 PVDD NC 13 6 VSSG CCD_OUT 12 7 POFF (N.C.) GND 11 8 RESET GND 10 9 SCLK GND 9 10 SI CAM_15V 8 11 XCS GND 7 12 D0 PWR_SAVE 6 13 D1

D901 BACKLIGHT GND 514 D2

RG 4 15 D3 GND 3 16 D4 VSUB 2

LCD901 17 D5 VSUB_CONT 118 D6

3INCH 19 D720 DCK

COLOR 21 HD22 VD FP-316 FLEXIBLE BOARD LCD UNIT 23 COMDC(L) (MAGIC FLEXIBLE)24 COMDC(H)

25 COMAC 26 VBRT 27 4.2VADJ 28 Vcc2

TOUCH PANEL 29 VCC1

30 GND 31 GND CN951 (MULTI CONNECTOR) 2 XSTATION_IN ACV_GND14SET_IN_ID ACV_GND 3 CN001 12P 6 USB_VBUS ACV_GND51VSS 8 USB_GND XPOWER_ON 7

MS-292 2 MS_BS MC-158 10 USB_D+ CRADLE_AD2 911BT901 3 DATA1 12 USB_D- N.C. 11 BATTERY FLEXIBLE TERMINAL 4 SDIO/DATA0 BOARD 14 USB_GND N.C. 135 DATA2

LND022 MEMORY 16 A_OUT_L CRADLE_AD1 15 6 INT STICKBOARD (MULTI CONNECTOR)DUO 18 A_GND CHARGE_V 17LND023S7DATA3 20 V_OUT BATT_XEXT 19

MEMORY STICK CONNECTOR, 8 SCLK 12 22 V_GND CHARGE_V 21LND024

9 VCC 24 XCHG_ON ACV_UNREG 23

BATTERY IN 10 VSS 26 XAV_JACK_IN ACV_UNREG 25

TO AV/USB MULTI CABLE OR CRADLE 4-1 4-2 FRAME CN002 6P CN001 12P 6 BL_L 12 BL_L 5 BL_L 11 NC 4 NC 10 BL_H 3 NC 9 NC 2 BL_H 8 KEY_AD0 1 BL_H 7 REG_GND CN001 6P 6 MODE_DIAL0 6 NC 5 M_5V 5 TOUCH_PANEL_XL 4 TOUCH_PANEL_XL 4 TOUCH_PANEL_XR 3 TOUCH_PANEL_XR 3 NC 2 TOUCH_PANEL_YL 2 TOUCH_PANEL_YL 1 TOUCH_PANEL_YU 1 TOUCH_PANEL_YU CN708 14P CN715 20P ST_UNREG 14 1 BATT_GND ST_UNREG 13 2 BATT_GND ST_UNREG 12 3 BATT_GND REG_GND 11 4 BATT_GND REG_GND 10 5 BATT_SIG REG_GND96BATT_UNREG REG_GND87BATT_UNREG M_5V78BATT_UNREG STRB_CHG69BATT_UNREG XSTRB_FULL 5 10 N.C. STRB_CHG_CONT 4 11 VSS STRB_ON 3 12 VCC D_3.2V 2 13 SCLK XAF_LED 1 14 DATA3 15 INT 16 DATA2 17 SDIO/DATA0 18 DATA1 19 MS_BS 20 VSS W952 W-43P CN716 MAGIC-43P GND 43 1 GND GND 42 2 GND GND 41 3 GND GND 40 4 GND GND 39 5 GND GND 38 6 GND XSTATION_IN 37 7 xSTATION_IN XPOWER_ON 36 8 N.C.(SET_IN_ID) N.C. 35 9 xPWR_ON CRADLE_AD2 34 10 CRADLE_AD2 CRADLE_AD1 33 11 A_GND A_GND 32 12 CRADLE_AD1 A_OUT_L 31 13 A_OUT_L N.C. 30 14 VGND V_GND 29 15 N.C V_OUT 28 16 V_LINE_OUT N.C. 27 17 USB_VBUS USB_VBUS 26 18 N.C. USB_GND 25 19 USB_GND USB_GND 24 20 D+ USB_D+ 23 21 USB_GND N.C. 22 22 N.C. USB_GND 21 23 D- USB_D- 20 24 USB_GND USB_GND 19 25 USB_GND BATT_XEXT 18 26 XCHG_ON XCHG_ON 17 27 BATT/XEXT XAV_JACK_IN 16 28 XAV_JACK_IN CHARGE_V 15 29 CHARGE_V CHARGE_V 14 30 CHARGE_V CHARGE_V 13 31 CHARGE_V CHARGE_V 12 32 CHARGE_V CHARGE_V 11 33 CHARGE_V ACV_UNREG 10 34 ACV_UNREG ACV_UNREG 9 35 ACV_UNREG ACV_UNREG 8 36 ACV_UNREG ACV_UNREG 7 37 ACV_UNREG N.C. 6 38 N.C N.C. 5 39 N.C N.C. 4 40 N.C STATIC_GND 3 41 STATIC_GND STATIC_GND 2 42 STATIC_GND STATIC_GND 1 43 STATIC_GND, 4-2. SCHEMATIC DIAGRAMS

Link

CD-585 FLEXIBLE BOARD (CCD IMAGER) SP-046 FLEXIBLE BOARD(SPEAKER, MIC) ST-129 FLEXIBLE BOARD (FLASH DRIVE) SW-460 FLEXIBLE BOARD (CONTROL SWITCH) RL-062 FLEXIBLE BOARD MS-292 FLEXIBLE BOARD (CONTROL SWITCH) (MEMORY STICK CONNECTOR, BATTERY IN) COMMON NOTE FOR SCHEMATIC DIAGRAMS, 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ µ Pattern boxF. 50 V or less are not indicated except for electrolytics Color bar chart and tantalums. Pattern box PTB-450 For PTB-450: • Chip resistors are 1/10 W unless otherwise noted. J-6082-200-A J-6020-250-A kΩ=1000 Ω, MΩ or=1000 kΩ. Small pattern box For PTB-1450: • Caution when replacing chip parts. PTB-1450 J-6082-559-A New parts must be attached after removal of chip. J-6082-557-A Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. L = About 30 cm (PTB-450) • Some chip part will be indicated as follows. L = About 13 cm (PTB-1450) Example C541 L452 22U 10UH Pattern box Front of the lens TA A 2520 L Camera Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. 2. Adjust the distance so that the output waveform of • Parts with ★ differ according to the model/destination. Fig. a and the Fig. b can be obtain. Refer to the mount table for each function.

H

• All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A : B+ Line • B : B– LineABA=BBA• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform) • C: adjustment for repair. • A : not use circuit • Circled numbers refer to waveforms. Electronic beam scanning frame (Measuring conditions voltage and waveform) • Voltages and waveforms are measured between the CRT picture frame measurement points and ground when camera shoots color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input Fig.b (Picture on monitor TV) impedance of VOM used.) When indicating parts by reference number, please Precautions for Replacement of Imager include the board name. • If the imager has been replaced, carry out all the adjustments for the camera section. The components identified by mark 0 or dotted line with • As the imager may be damaged by static electricity from mark 0 are critical for safety. its structure, handle it carefully like for the MOS IC. Replace only with part number specified. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4-5 Yellow Cyan Green White Magenta Red Blue,

Ver 1.1 2005.11

12345678910

CD-585 FLEXIBLE BOARD Note: CD-585 flexible complete board, IC001 and IC002 are not supplied, but they are included in A CCD IMAGER CCD adaptor mounted block assy.Note: Voltages and Waveforms of IC001 and IC002 can XX MARK:NO MOUNT not be measured, because they are mounted by M:REC (MOVIE) MODE the side of the lens. R:REC (STILL) MODE P:PB MODE B

LND007 CAM_-8V 39 LND008 NC 38 LND009 V10 37 LND010 V9 36 LND011 V8 35 LND012 V7 34

C LND013 V6 33LND014 V5B 32

LND015 V5A 31 LND016 V4 30 LND017 V3B 29 LND018 V3A 28 LND019 VHLD 27 LND020 V2 26

D LND021 VST 25

LND022 V1 24

SY-138

(1/8) LND023 GND 23 CN101 LND024 H2A 22 PAGE 4-9 LND025 of LEVEL3 H1A 21 LND026 GND 20 16 15 14 13 12 11 10987654321LND027 H1B 19 LND028 H2B 18

E LND029 GND 17LND030 GND 16 IC001

LND031 GND 15321CCD IMAGER LND032 CCD_GND 14 IC001 ICX476CQZ-13 LND033 NC 13 LND034 CCD_OUT 12 IC002 LND035 GND 11 R001 BUFFER0 IC002 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 LND036 GND 10 CXA3691EN-T9456

F C001LND037 GND 9 XX C003

50V XX LND038 CAM_15V 8 C008 50V R010 0.01u LND039 GND 7 R009 220k 0 16V LND040 PWR_SAVE 6 LND041 GND 5 LND042 RG 4 LND043 GND 3 LND044 VSUB 2

G LND045 VSUB_CONT 1

Q002 R0040 DTC144EMT2L

SWITCH

C004 R005 C002 1k C005 M:3.2/ XX 0.22u 0.1u R:0/P:0 M:0/ 16V 16V 10V R:3.2/P:0

H

4-7 4-8 CD-585

OUT IDRV GND VCC IN ISF

VOUT NC NC V10 GND V9 CL001 GND V8 GND V7 CL003 VDD V6 RG V5B C007 0.1u 16V CL007 H2B V5A H1B V4 SUB V3B CL020 CL002 CSUB V3A CL021 CL011 H1A VHLD H2A V2 VL VST GND NC NC V1 CL014, Schematic diagrams of the SY-138, MC-158 and FP-316 flexible boards are not shown. Pages from 4-9 to 4-24 are not shown., • Refer to page 4-5 for mark 0. 12345678910

ST-129 FLEXIBLE BOARD A FLASH DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE

T001 D001 CRF02(TE85R) LND019 LND001 ST_UNREG 1426XE_A(H) L001

B LND002 ST_UNREG 13 2.2uH R0041M

LND003 ST_UNREG 12 1 LND017 LND004 REG_GND 11 C001 22u TRIGGER LND005 REG_GND 10 6.3V C901 105u

SY-138 LND006 REG_GND94315V C004

(2/8) LND007 CHARGING 0.047u LND018 FLASH REG_GND 8 CAPACITOR LND015 250V UNIT CN708 TRIG_GNDLND008 M_5V 7 CHARGE+ PAGE 4-1235of LEVEL3 LND009 STRB_CHG 6 CHARGE- LND010 XSTRB_FULL 5 LND016

C LND020LND011 STRB_CHG_CONT 4

XE_K(L) LND012 STRB_ON 3 LND013 D_3.2V 2 4.261LND014 XAF_LED 1 17 16 15 14 135243D002

D TLOH9203(SONY) C002SELF TIMER/ 1u 4.2 PGND

AF ILLUMINATOR 6.3V SW IC001 PGND SW FLASH CONTROL, 5 CHARGE CONTROL CHG051270 VCC IC001TPS65552RGTR620XFULL 3.2 F_ON7384Q001 R002 0 TIG022TS-S-TL-E 4.7M FLASH DRIVEE5678R00300

F

4-25 4-26 ST-1294321N.C HGND I_PEAK N.C G_IGBT VBATT N.C N.C N.C 9 10 11 12, 12345678910 11 12 13 14

A RL-062 B FLEXIBLE BOARD Note: MIC901 and SP901 are not included CONTROL SWITCH in SP-046 flexible board. XX MARK:NO MOUNT S002

(SHUTTER) LND001 XAE_LOCK_SW 25 3 NO 1 SP-046 LND002 NC 24 LND003 XSHUTTER_SW 2324FLEXIBLE BOARD LND004 REG_GND 22

C LND005 TLGV1021(T15SOY2,F TLGV1021(T15SOY2,F SPEAKER, MICPWR_LED_A 21 S001

D001 D004 LND006 POWERNC 20 (POWER) (POWER) 2 1 CN002 6P LND007 PWR_LED_K 19 1 NC LND006 NC 1 LND008 XPWR_ON 18 2 NC LND0053 NC LND009 MIC_SIG 17 3 MIC_SIG LND004 MIC_SIG 3 MIC_SIG LND010 MIC MIC901 LND010 MIC_GND 16 4 MIC_GND LND003 MIC_GND 4 MIC_GND LND009 LND011 SP+ 15 5 SP+ LND002 SP+ 5 SP+ LND008 SP901

D SY-138 LND012 SP- 14 6 SP- LND001 SP- 6 SPEAKER

SP- LND007 (8/8) LND013 TOUCH_PANEL_YU 13 CN710 LND014 TOUCH_PANEL_YL 12 PAGE 4-24 of LEVEL3 LND015 TOUCH_PANEL_XR 11 LND016 TOUCH_PANEL_XL 10 SW-460 FLEXIBLE BOARD LND017 M_5V 9 LND018 MODE_DIAL0 8 CONTROL SWITCH LND019 REG_GND 7 CN001 6P LND020 NC 6 CN001 12P 1 TOUCH_PANEL_YUE LND021 LND012 2 TOUCH_PANEL_YL LCD901KEY_AD051TOUCH_PANEL_YU TOUCH_PANEL_YU 1 (2/2) LND022 NC42TOUCH_PANEL_YL LND011 TOUCH_PANEL_YL23NC TOUCH LND023 BL_H33TOUCH_PANEL_XR LND010 TOUCH_PANEL_XR34TOUCH_PANEL_XR PANEL

WITH

LND024 NC24TOUCH_PANEL_XL LND009 TOUCH_PANEL_XL45TOUCH_PANEL_XL LCD UNIT LND025 BL_L15M_5V LND008 M_5V 5 R006 6 NC 6 MODE_DIAL0 LND007 MODE_DIAL067REG_GND LND006 REG_GND 7

F 8 KEY_AD0 LND005 KEY_AD0 8

9 NC LND004 NC 9 CN002 6P D901 10 BL_H LND003 BL_H 10 1 BL_H BACKLIGHT 11 NC LND002 NC 11 2 BL_H 12 BL_L LND001 BL_L 12 3 NC D002 D003 4 NC XX XX T (ZOOM) W 5 BL_L S001 S002 LND02621216BL_L STATIC_GND

G

4343R002 R003 1200 1500 S005 S003 9 10 TOUCH MOVIE PANEL6214

H 3 STILL

431D004 R007S004 SO-194S-PB178-SD-T 10k78(KEY ILLUMINATION) SCREENSTATUS21R00443

I D005SO-194S-PB178-SD-T Note: Replace D004 and D005 together,

(KEY ILLUMINATION) when you repair D004 or D005. 4-27 4-28 RL-062, SP-046, SW-460 2200 R008 2200 R009, • Refer to page 4-5 for mark 0. 123456

MS-292 FLEXIBLE BOARD A MEMORY STICK CONNECTOR, BATTERY IN

CN001 12P LND001 VSS 20 1 VSS LND002 MS_BS 19 2 MS_BS LND003 DATA1 18 3 DATA1

B LND004 SDIO/DATA0 17 4 SDIO/DATA0

LND005 DATA2 16 5 DATA2 MEMORY LND006 INT 15 6 INT STICKDUO LND007 DATA3 14 7 DATA3 LND008 SCLK 13 8 SCLK 12 SY-138 LND009 VCC 12 9 VCC (8/8) LND010 VSS 11 10 VSS CN715 LND011 PAGE 4-23 NC 10 of LEVEL3 LND012 BATT_UNREG 9

C LND013 BATT_UNREG 8

LND014 BATT_UNREG 7 LND015 BATT_UNREG 6 BATT_UNREG LND022 LND016 BATT_SIG 5 BATT_SIG LND023 LND017 S BT901BATT_GND 4 BATT_GND LND024 BATTERY LND018 TERMINALBATT_GND 3 LND019 BATT_GND 2

D LND020 BATT_GND 1

4-29 4-30 MS-292, 4-3. PRINTED WIRING BOARDS Link CD-585 FLEXIBLE BOARD SP-046 FLEXIBLE BOARD ST-129 BOARD SW-460 FLEXIBLE BOARD RL-062 FLEXIBLE BOARD MS-292 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS, 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 1221324334654456• Circled numbers refer to waveforms. • There are a few cases that the part printed on diagram543345411221123321isn’t mounted in this model. 3 2 • C: panel designation414-31,

CD-585 (2 layers)

: Uses unleaded solder.

CD-585 FLEXIBLE BOARD

16 1532C00331

IC001 C005

39 IC002 LND007 LND00846LND009 LND010 LND011 LND012 LND013 17 LND014 LND015 LND016 C002 LND017 LND018 LND019 LND020 18 19 LND021 CD585 31 32LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032 LND033 LND034 LND035 LND036 LND037 LND038 LND039 LND040 Note: CD-585 flexible complete board, IC001 and LND041 LND042 LND043 R001 LND044 R009 IC002 are not supplied, but they are included 05 LND045 1 in CCD adaptor mount block assy.ID R004 R005 C007 1-868-865- 11 4-33 4-34 CD-585

Q002

ECBC004 C001 C008 R010, Printed wiring boards of the SY-138, MC-158, and FP-316 flexible boards are not shown. Pages from 4-35 and 4-36 are not shown.,

ST-129 (2 layers)

: Uses unleaded solder.

ST-129 FLEXIBLE BOARD FLASH UNIT

XE_K (L) XE_A (H) R004 C004 R002426D001AKT001 LND017 + 1LND001LND018 L001 LND002 LND003351C901 LND00441CHARGING LND005LND006 5 16 CAPACITOR LND007 17 LND008LND009 8 13 LND010 LND011 9 12 LND012

IC001 LND013LND014

1-868-852- 11 05 ST D002-12 6 SELF TIMER/9 AF ILLUMINATOR 4-37 4-38 ST-129 LND02041

Q001

5 8 R003 TRIG_GND

TRIGGER

C001 C002 LND016 LND015 LND019,

RL-062 (1 layer), SP-046 (1 layer), SW-460 (1 layer) Ver 1.1 2005.11

: Uses unleaded solder. SW-460 FLEXIBLE BOARD 12 1

D001, D004 D004 D002

(POWER) 11 2

D003

1223

S001

S001

POWER S002>PI<

3443

S002 RL-062 FLEXIBLE BOARD (SHUTTER)

CN002

RL-062

1 12 CN001 (ZOOM)

S002 S001 W T

2424S002 S001 25113131-868-855- 11

SP-046 FLEXIBLE BOARD R006 R002

MIC901

Note: MIC901 and SP901 are not included in SP-046 flexible board.

6 MIC_GND MIC_SIG S005 LND006 MOVIE LND005 LND004 LND003 LND009 LND002 LND001 LND010 STILL

N D004 D004 KEY ILLUMINATION

2 4 S003

Replace D004 and D005 together,

S003 when you repair D004 or D005. TOUCH13PANEL

D005 D005 KEY ILLUMINATION

2 4 S004 S004 SCREEN13STATUS LND008 LND007 SP- SP+ 1-868-859- 11 1-868-854- 11 SP901 4-39 4-40 RL-062, SP-046, SW-46061

D001

LND025 LND024 LND023 LND022 LND021 LND020 LND019 LND018 LND017 LND016 LND015 LND014 LND013 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001 LND012 LND011 LND010 LND009 LND008 LND007 LND006 LND005 LND004 LND003 LND002 LND001 R009 R008 R007 CN0011234566179S005 8 10 R004 R003

SW-460

>PI< 1 6 CN002 SP-046,

MS-292 (1 layer)

: Uses unleaded solder.

MS-292 FLEXIBLE BOARD

LND022 BT901

BATTERY TERMINAL

-11 BATT_UNREG + LND023 BATT_SIG S BATT_GND

MEMORY - STICK

CN001

DUO LND024

LND020 LND019 LND018 11 LND017 LND016 LND015 LND014 LND013 LND012

MS292 LND011LND010

LND009 LND008 LND007 LND006 LND005 05 LND004 LND003 LND002 LND001 1-868-856- 11 4-41 4-42 MS-292, Waveforms of the SY-138 board are not shown. Page 4-43 is not shown. 4-45, Mounted parts location of the SY-138, MC-158 and FP-316 flexible boards are not shown. Page 4-44 is not shown. 4-47,

NOTE

5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCOVERALL SECTION LENS BLOCK SECTION CABINET (MAIN) SECTIONDECABINET (CENTER) SECTION CABINET (REAR) SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

CD-585 FLEXIBLE BOARD B RL-062 FLEXIBLE BOARD C ST-129 FLEXIBLE BOARD A MS-292 FLEXIBLE BOARD C SP-046 BOARD C SW-460 FLEXIBLE BOARD E, 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant µ le numéro spécifié.uF: F • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model • Language that can be selected about SY-138 board GP1Jz

US CND

GP2zzzzzz

AUS

Vietnam

AEP

GP3zzzzzzzzzzzzzzz

UK E AR BR TW

GP4zzzzzzzzz

JE HK CH KR

5-1 Area Japanese English French German Spanish Italian Portugal Simplified Chinese Traditional Chinese Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech Persian Thai, 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL SECTION ns: not supplied C901 4 Cabinet (main) section (See page 5-4.) ns 3 BT001 5 ! 2672Lens block section (See page 5-3.) ! BT001 (BATTERY, LITHIUM SECONDARY) Board on the mount position (See page 4-36).

CAUTION

* Refer to the table of page 5-1 about language of SY-138 board. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description 1 A-1151-923-A CABINET (FRONT) BLOCK ASSY 8 A-1161-638-A SY138-MC158 BOARD, COMPLETE 2 2-587-151-01 SCREW (M1.4), NEW TRUSTAR. P2 (SERVICE) (GP2) 03 1-479-601-11 FLASH UNIT 8 A-1161-639-A SY138-MC158 BOARD, COMPLETE 04 A-1151-928-A ST-129 FLEXIBLE BOARD, COMPLETE (SERVICE) (GP3) * 5 2-657-990-01 HOLDER (AF) 8 A-1161-640-A SY138-MC158 BOARD, COMPLETE (SERVICE) (GP4) 6 2-657-991-01 CAP, MULTI * 9 2-658-008-01 CUSHION (CD) 7 2-660-401-11 SCREW, TAPPING, P2 8 A-1161-637-A SY138-MC158 BOARD, COMPLETE 0*BT001 1-756-566-11 BATTERY, LITHIUM SECONDARY (SERVICE) (GP1) 0*C901 1-112-809-11 CAP, ELECT 105uF 315V 5-2, 5. REPAIR PARTS LIST (including CD-585 62 flexible board and 5-1-2. LENS BLOCK SECTION CCD imager (IC001)) (Note 1, 2) ns: not supplied 62 (Note 4) 64 56 (Note 4) 54 ns (Note 4, 5) 55 63 (Note 4) (Note 4) 66 ns (Note 4, 5) 67 (Note 3) 59 ns (Note 3) (Note 4) (Note 4) 51 Note 3: Be sure to read “Exchange method of barrier as- (Note 3, 4) sembly” on page 2-7. Note 1: CCD adaptor mount block assembly is includ- Note 4: Be sure to read “Exchange method of LSV-1100A” ing CD-585 flexible completed board. on page 2-10. Note 2: Be sure to read “Precuations for Replacement of Note 5: Non-replaceable part. Imager” on page 4-5. If it is damaged, replace the whole lens. Ref. No. Part No. Description Ref. No. Part No. Description 51 8-848-799-01 LSV-1100A (Note 3, 4) 60 A-1153-444-A BARRIER BLOCK ASSY (Note 3) 52 2-596-758-01 RETAINER, LPF 61 2-591-008-01 SPRING (A), BARRIER 53 2-596-756-01 MASK, LPF 62 2-663-791-01 SHEET (CD) 54 1-788-291-11 FILTER BLOCK, OPTICAL 63 1-479-387-11 GEAR BLOCK, ZOOM (1100) (Note 4) 55 2-596-755-01 RUBBER (1100), SEAL 64 3-086-156-21 SCREW B1.2 (Note 4) 56 3-086-156-21 SCREW B1.2 65 2-593-175-01 PLATE SPRING, Z (Note 4) * 57 2-658-008-01 CUSHION (CD) 66 2-659-328-02 WASHER,NARUTO 58 X-2067-995-1 MOUNT BLOCK ASSY, CCD ADAPTOR 67 X-2108-530-1 GEAR, NARUTO (S) (including CD-585 flexible board and IC001) 68 2-591-031-01 PLATE SPRING, F (Note 4) (Note 1, 2) 69 2-593-176-01 PLATE SPRING, S (Note 4) 59 2-591-013-01 RING (A), ORNAMENTAL (Note 3) 5-3, 5. REPAIR PARTS LIST 5-1-3. CABINET (MAIN) SECTION ns: not supplied MIC901 BT901 SP901 CN001 ns 101 Cabinet (center) section (See page 5-5.) • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description * 101 2-657-989-01 PLATE, MS GROUND * 107 2-657-901-01 FRAME (RELEASE) 102 A-1151-968-A MS-292 FLEXIBLE BOARD, COMPLETE 0BT901 1-780-061-21 BATTERY TERMINAL BOARD 103 3-078-890-01 SCREW, TAPPING CN001 1-817-827-11 MEMORY STICK DUO CONNECTOR 104 A-1151-930-A RL-062 FLEXIBLE BOARD, COMPLETE MIC901 1-542-666-01 MICROPHONE * 105 2-657-988-01 HOLDER, MICROPHONE SP901 1-825-945-11 LOUDSPEAKER (1.3CM) 106 1-868-859-11 SP-046 FLEXIBLE BOARD 5-4, 5. REPAIR PARTS LIST 5-1-4. CABINET (CENTER) SECTION ns: not supplied Cabinet (rear) section (See page 5-6.) (Note) (Note) ns ns (Note) ns 152 (Note) ns Note: Be sure to read “The method of attachment of cabinet center block” on page 2-5, 2-6. Ref. No. Part No. Description Ref. No. Part No. Description 151 2-665-774-01 SCREW 156 X-2102-864-1 CABINET (CENTER) ASSY 152 2-657-902-01 PLATE (MULTI), FIXED * 157 2-657-907-01 SPRING, BT DISCHARGE * 153 2-657-913-01 CLAW (BT), LOCK (Note) 158 2-587-151-01 SCREW (M1.4), NEW TRUSTAR.P2 * 154 2-657-915-01 LIGHT, MS GUIDE, (Note) 159 2-660-401-11 SCREW, TAPPING, P2 155 2-657-909-01 LID (BT) 5-5, 5. REPAIR PARTS LIST 5-1-5. CABINET (REAR) SECTION ns: not supplied (including LCD) ns 201 D901 Ref. No. Part No. Description Ref. No. Part No. Description * 201 2-657-992-01 PLATE (LCD), RETAINER * 204 2-657-995-01 SHEET (LCD) 202 A-1151-929-A SW-460 FLEXIBLE BOARD, COMPLETE 205 A-1148-563-A TP BLOCK ASSY (30STGU) (including LCD) 203 X-2102-867-1 CABINET (REAR) ASSY D901 1-479-403-11 BLOCK, LIGHT GUIDE PLATE (3.0) 5-6,

CD-585

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description X-2067-995-1 MOUNT BLOCK ASSY, CCD ADAPTOR (Note) (Not supplied) CD-585 FLEXIBLE BOARD, COMPLETE ******************************* (CD-585 flexible complete board, IC001 and IC002 are not supplied, but they are included in CCD adaptor mount block assy) < CAPACITOR > C002 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V C005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C007 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C008 1-164-943-81 CERAMIC CHIP 0.01uF 10% 16V < IC > IC001 (Not supplied) IC ICX476CQZ-13 (Note) IC002 (Not supplied) IC CXA3691EN-T9 < TRANSISTOR > Q002 6-550-119-01 TRANSISTOR DTC144EMT2L < RESISTOR > R001 1-218-990-81 SHORT CHIP 0 R004 1-218-990-81 SHORT CHIP 0 R005 1-218-953-11 RES-CHIP 1K 5% 1/16W R009 1-218-990-81 SHORT CHIP 0 R010 1-218-981-11 RES-CHIP 220K 5% 1/16W

Electrical parts list of FP-316 flexible and MC-158 board are not shown. Pages 5-8 is not shown.

Note: Be sure to read “Precautions for Replacement of Imager” on page 4-5 when changing the imager. 5-7,

MS-292 RL-062 SP-046 ST-129 SW-460

Ref. No. Part No. Description Ref. No. Part No. Description A-1151-968-A MS-292 FLEXIBLE BOARD, COMPLETE < TRANSISTOR > ******************************* 0*Q001 6-551-447-01 TRANSISTOR TIG022TS-S-TL-E < BATTERY TERMINAL > < RESISTOR > 0BT901 1-780-061-21 BATTERY TERMINAL BOARD R002 1-243-975-81 METAL CHIP 4.7M 5% 1/16W < CONNECTOR > R003 1-208-647-11 METAL CHIP 33 0.5% 1/16W R004 1-216-121-11 RES-CHIP 1M 5% 1/10W CN001 1-817-827-11 MEMORY STICK DUO CONNECTOR < TRANSFORMER > A-1151-930-A RL-062 FLEXIBLE BOARD, COMPLETE 0T001 1-443-880-21 TRANSFORMER, DC-DC CONVERTER ******************************* < CONNECTOR > A-1151-929-A SW-460 FLEXIBLE BOARD, COMPLETE ******************************** * CN001 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P * CN002 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P < CONNECTOR > < DIODE > * CN001 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P * CN002 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P D001 6-500-532-01 DIODE TLGV1021 (T15SOY2, F (POWER) D004 6-500-532-01 DIODE TLGV1021 (T15SOY2, F (POWER) < DIODE > < SWITCH > * D004 6-501-435-01 DIODE SO-194S-PB178-SD (KEY ILLUMINATION) (Note) S001 1-786-685-31 SWITCH, TACTILE (POWER) * D005 6-501-435-01 DIODE SO-194S-PB178-SD S002 1-786-602-11 SWITCH, TACTILE (SHUTTER) (KEY ILLUMINATION) (Note) < RESISTOR > 1-868-859-11 SP-046 FLEXIBLE BOARD ********************* R002 1-216-822-11 METAL CHIP 1.2K 5% 1/10W (MIC901 and SP901 are not included in SP-046 flexible board) R003 1-216-823-11 METAL CHIP 1.5K 5% 1/10W < MICROPHONE > R004 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R006 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W MIC901 1-542-666-01 MICROPHONE R007 1-216-833-11 METAL CHIP 10K 5% 1/10W < SPEAKER > R008 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R009 1-216-825-11 METAL CHIP 2.2K 5% 1/10W SP901 1-825-945-11 LOUDSPEAKER (1.3CM) < SWITCH > 0 A-1151-928-A ST-129 FLEXIBLE BOARD, COMPLETE S001 1-786-685-31 SWITCH, TACTILE (T (ZOOM)) ******************************* S002 1-786-685-31 SWITCH, TACTILE (W (ZOOM)) S003 1-786-685-31 SWITCH, TACTILE (TOUCH PANEL) 0 1-479-601-11 FLASH UNIT S004 1-786-685-31 SWITCH, TACTILE (SCREEN STATUS) S005 1-771-487-21 SWITCH, SLIDE (PLAY/STILL/MOVE) < CAPACITOR > C001 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V C002 1-100-506-91 CERAMIC CHIP 1uF 20% 6.3V Electrical parts list of the SY-138 board is C004 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V not shown. 0*C901 1-112-809-11 CAP, ELECT 105uF 315V Pages 5-10 to 5-13 are not shown. < DIODE > 0D001 6-501-096-01 DIODE CRF02 (TE85R) * D002 6-501-313-01 DIODE TLOH9203 (SONY) (SELF TIMER/AF ILLUMINATOR) < IC > 0 IC001 6-707-555-01 IC TPS65552RGTR < COIL > L001 1-400-820-11 INDUCTOR 2.2uH • Refer to page 5-1 for mark 0.* Note: Replace D004 and D005 together, when you repair D004 or D005. 5-9,

Ver 1.1 2005.11 Checking supplied accessories.

Battery charger BC-CSG (1) Power cord (main lead) (1) USB, A/V, DC IN cable for Wrist strap (1) 0 1-479-583-11 (J) 0 1-776-985-11 (KR) multi-use terminal (1) 2-050-981-01 0 1-479-583-21 (US, CND) 0 1-782-476-51 (CH) 1-830-848-11 0 1-479-583-31 (EXCEPT US, CND, J) 0 1-783-374-11 (UK, HK) 0 1-790-732-71 (JE) 0 1-823-946-12 (AEP, E) 0 1-827-945-11 (AUS) Rechargeable battery pack Battery case (1) Stylus (1) NP-BG1 (1) (not supplied) 2-657-889-01 (not supplied) Conversion adaptor (1) Conversion adaptor (1) CD-ROM 0 1-569-008-21 (E) 0 1-569-007-12 (JE) (Cyber-shot application software) (1) 2-655-049-01 • Refer to page 5-1 for mark 0. 5-14,

Checking supplied accessories. Other accessories

2-652-805-01 INSTRUCTION (READ THIS FIRST) (JAPANESE) (J) 2-652-806-41 INSTRUCTION (USER’S GUIDE) (GERMAN, DUTCH) 2-652-805-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP) (EXCEPT US, CND, KR, CH, J) 2-652-805-21 INSTRUCTION (READ THIS FIRST) 2-652-806-51 INSTRUCTION (USER’S GUIDE) (TRADITIONAL (FRENCH, ITALIAN) (AEP) CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-652-805-31 INSTRUCTION (READ THIS FIRST) 2-652-806-61 INSTRUCTION (USER’S GUIDE) (RUSSIAN) (AEP) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-652-806-71 INSTRUCTION (USER’S GUIDE) (ARABIC, PERSIAN) 2-652-805-41 INSTRUCTION (READ THIS FIRST) (E) (GERMAN, DUTCH) (AEP) 2-652-806-81 INSTRUCTION (USER’S GUIDE) (KOREAN) (KR, JE) 2-652-806-91 INSTRUCTION (USER’S GUIDE) (POLISH, CZECH) 2-652-805-51 INSTRUCTION (READ THIS FIRST) (AEP) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-652-807-11 INSTRUCTION (READ THIS FIRST) 2-652-805-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN) (AEP) (HUNGARIAN, SLOVAKIAN) (AEP) 2-652-805-71 INSTRUCTION (READ THIS FIRST) 2-652-807-21 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) (SWEDISH, FINNISH) (AEP) 2-652-805-81 INSTRUCTION (READ THIS FIRST) (KOREAN) 2-652-807-31 INSTRUCTION (READ THIS FIRST) (KR, JE) (NORWEGIAN, DANISH) (AEP) 2-652-805-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) 2-652-808-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP) (US, CND) 2-652-808-21 INSTRUCTION (READ THIS FIRST) 2-652-806-01 INSTRUCTION (USER’S GUIDE) (JAPANESE) (J) (FRENCH, ITALIAN) (CND) 2-652-806-11 INSTRUCTION (USER’S GUIDE) (ENGLISH) (EXCEPT KR, CH, J) 2-652-809-11 INSTRUCTION (USER’S GUIDE) 2-652-806-21 INSTRUCTION (USER’S GUIDE) (FRENCH, ITALIAN) (HUNGARIAN, SLOVAKIAN) (AEP) (CND, AEP) 2-652-809-21 INSTRUCTION (USER’S GUIDE) 2-652-806-31 INSTRUCTION (USER’S GUIDE) (SWEDISH, FINNISH) (AEP) (SPANISH, PORTUGUESE) (AEP, E, JE) 2-652-809-31 INSTRUCTION (USER’S GUIDE) (NORWEGIAN, DANISH) (AEP) 5-15E, [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once 1. Click the Print button . • To reverse the previous screens (operation) one by one, click 2. Specify a printer, print range, number of copies, and other op- the . tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click the . Application of printing: To set a range to be printed within a page, select the graphic Application to the Service Manual: selection tool and drag on the page to enclose a range to This function allows you to go and back between circuit dia- be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it will be convenient for the voltage check. Finding a text 1. Click the Find button . Moving with link 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool , or graphic selection tool . Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing “Find”. page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.) Moving with bookmark: Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.) Application to the Service Manual: The parts on the drawing pages (block diagrams, circuit dia- grams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display the circuit diagram or printed circuit board diagram succes- “Zoom in/out” sively. • Click the triangle button in the zoom control box to select the Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom- Manual depending on the date of issue. ing in or out. Switching a page • To move to the first page, click the . • To move to the last page, click the . “Rotate” • To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each. • To move to the next page, click the . Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set.,

Reverse 987690833.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2005.10 Official Release — — 1.1 2005.11 Correction-1 • Correction of Block Diagrams Yes (C1) • Correction of Schematic Diagram • Correction of Printed Wiring Board • Correction of Repair Parts S.M. correction: Page 3-1, Page 3-3, Page 3-5, Page 4-7, Page 4-39, Page 5-14 1.2 2005.12 Revised-1 • Change of Disassembly of Lens Block Yes]
15

Similar documents

SECTION 6 ADJUSTMENTS
DSC-H50 RMT-DSC2 Ver. 1.3 2008.09 SECTION 6 Auto-ADJ Revision History ADJUSTMENTS Link Before starting adjustments SERVICE MODE Adjusting items when replacing main parts and boards APPLICATION FOR ADJUSTMENT (SeusEX) List of service tools SERVICE MODE DATA BACKUP CAMERA SECTION ADJUSTMENTS PREPARATI
These specifications are extracted from
DCR-HC36/HC36E RMT-831 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2006.08 Canadian Model Revision History North European Model How to use E Model Acrobat Reader Australian Model Chinese Model Hong Kong Model Korea Model N MECHANISM (MDX-N110) Photo: DCR-HC36 Link SPECIFICATIONS DISASSEMBLY SCHEMATIC DI
SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.3 2005.12 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
DSC-P1 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.0 2000. 10 Hong Kong Model Australian Model Chinese Model Korea Model
DSC-P1 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.0 2000. 10 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please
Model information table
DCR-HC36/HC36E RMT-831 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2006.08 Canadian Model Revision History North European Model How to use E Model Acrobat Reader Australian Model Chinese Model Hong Kong Model Korea Model N MECHANISM (MDX-N110) Photo: DCR-HC36 Link MODEL INFORMATION TABLE PRINTED WIRING
DSC-H5 MANUAL DE SERVIÇO LEVEL 3 Brazilian Model Ver. 1.1 2006. 06 Link
DSC-H5 MANUAL DE SERVIÇO LEVEL 3 Brazilian Model Ver. 1.1 2006. 06 Revision History Instruções de Acrobat Reader Memória Interna na PLACA Link NOTA DE SERVIÇO PLACAS DE CIRCUITO IMPRESSO DIAGRAMAS ESQUEMÁTICOS LISTA DE PEÇAS PARA REPARO Note : Note : The components identified by Les composants ident
Training Manual Digital Still Camera Servicing Models: DSC-S75 DSC-S85 DSC-F707 Circuit Descriptions and Troubleshooting Course: DSC-02
Training Manual DSC-S75 DSC-S85 DSC-F707 Digital Still Camera Servicing Models: DSC-S75 DSC-S85 DSC-F707 Circuit Descriptions and Troubleshooting Course: DSC-02 Table of Contents 1.Overview ...1 DSC-F707 10. Features ...22 Symbol Explanations ... 1 11. Repair Tools & Jigs...23 2. Software - All Mode
SPECIFICATIONS [System] [LCD screen]
DSC-S700 SERVICE MANUAL US Model Ver. 1.1 2007.10 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Chinese Model Internal memory Korea Model ON BOARD Revised-1 Replace the previously issued SERVICE MANUAL 9-852-183-11 with this Manual. Link SPECIF
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-H10 SERVICE MANUAL LEVEL 3 US Model Ver. 1.1 2008.05 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Thai Model Photo: Black Japanese Model Tourist Model Link SERVICE NO
SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-H10 SERVICE MANUAL LEVEL 2 US Model Ver. 1.1 2008.05 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Thai Model Photo: Black Japanese Model Tourist Model Link SPECIFICAT
DSC-V3 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-V3 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the
Compatibility issues between Cyber-shot and DSLR-A100
Compatibility issues between Cyber-shot and DSLR-A100 Applied Technology Dept., SE Div., DIG July 2006 SONY Confidential 1. NP-FM55H NP-FM55H is the battery supplied with DSLR-A100 and it is also sold separately. Its shape and size are the same as current M-series batteries such as NP-FM50 and can b
DSC-V3 SERVICE MANUAL LEVEL 2
DSC-V3 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
DSC-V3 SERVICE MANUAL LEVEL 2
DSC-V3 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004.10 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
DSC-V3 SERVICE MANUAL LEVEL 2
DSC-V3 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
SPECIFICATIONS Camera [Input and Output connectors]
DSC-S930 SERVICE MANUAL US Model Ver. 1.1 2009.07 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Chinese Model Korea Model Revised-1 Brazilian Model Replacement of the previously issued Tourist Model SERVICE MANUAL 9-852-674-11 with this manual.
SPECIFICATIONS Camera [Exposure] Operating temperature
DSLR-A100 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.06 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE
SPECIFICATIONS Camera [Input and Output connectors] BC-CSD battery charger
DSC-T70/T75 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.08 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Photo: Silver Japanese Model Tourist Model Link SPECIFICATIONS D
SPECIFICATIONS Camera [Exposure] Operating temperature
DSLR-A100 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2006.07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Revised-1 Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SE
6-1-2. FRONT CABINET ASSEMBLY
DSC-F505V SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • Items marked “*” are not stocked since they are Replace only with part number speci- have some d
Note: Follow the disassembly procedure in the numerical order given.
DSC-F505V SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. DSC-F505V 2-1. REAR CABINET BLOCK 2-2. ZOOM LENS BLOCK (Page 2-2) (Page 2-2) 2-5. LCD PANEL BLOCK 2-6. HI-73, DD-148 BOARDS, 2-3. CABINET (LT) BLOCK CONTROL SWITCH BLOCK (FK) BATTERY HOLDER BLOCK (Page 2-3) (Pag
Model information table
DSC-T70/T75 SERVICE MANUAL LEVEL 3 US Model Ver. 1.0 2007.08 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Photo: Silver Japanese Model Tourist Model Link SERVICE NOTE SCH
Supplied accessories
DSC-F505 SERVICE MANUAL US Model Canadian Model Level 2 Ver 1.2 2000. 03 With SUPPLEMENT-1 AEP Model (9-974-192-81) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model This service manual contains information for Japanese model as well. On the PS-427, SY-56 boar
DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06
DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06 On the SY-59 board This service manual contains information This service manual provides the information that is premised the circuit board for japanese model as well.
Page Changed contents
DSC-F55/F55E US Model Canadian Model SERVICE MANUAL Tourist ModelKorea Model DSC-F55 1999. 07 E Model DSC-F55/F55E AEP Model UK Model Australian Model Hong Kong Model Chinese Model DSC-F55E SUPPLEMENT-1 File this supplement-1 with the Service Manual. (99-009) Subject: • Addition of Korea model • Suf
AUTION ou are cautioned that any changes or
DSC-F717 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
Trademarks About the Carl Zeiss lens
DSC-F77/FX77 SERVICE MANUAL LEVEL 1 AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MAN
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL i