Download: SPECIFICATIONS Camera [Input and Output connectors] BC-CSD battery charger

DSC-T70/T75 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.08 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Photo: Silver Japanese Model Tourist Model Link SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST • Precaution on Replacing the SY-183 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiqu...
Author: Acal1978 Shared: 8/19/19
Downloads: 171 Views: 4633

Content

DSC-T70/T75 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.08 Canadian Model

Revision History AEP Model

UK Model

Internal memory E Model ON BOARD Australian Model

Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model

Photo: Silver Japanese Model

Tourist Model Link

SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST • Precaution on Replacing the SY-183 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-T70/T75_L2 2007H0800-1 © 2007.08 9-852-216-31 Sony EMCS Co. Published by Kohda TEC,

SPECIFICATIONS Camera [Input and Output connectors] BC-CSD battery charger

Power requirements: AC 100 V to 240 V, 50/60 Hz, [System] Multi connector : Video outputAudio output (Monaural) 2.2 W Image device: 7.18 mm (1/2.5 type) color CCD, USB communication Output voltage: DC 4.2 V, 0.33 A Primary color filter Operating temperature: 0 to 40 ºC (32 to 104 ºF) Total pixel number of camera: USB communication : Hi-Speed USB (USB 2.0 compliant) Storage temperature: –20 to +60 ºC (–4 to +140 ºF )Approx. 8 286 000 pixels [LCD screen] Dimensions: Approx. 62×24×91 mm (2 1/2× Effective pixel number of camera: Approx. 8 083 000 pixels LCD panel: Wide (16:9), 7.5 cm (3.0 type) TFT drive 31/32×3 5/8 inches) (W/H/D) Mass: Approx. 75 g (2.7 oz) Lens: Carl Zeiss Vario-Tessar 3× zoom lens f = Total number of dots: 230 400 (960×240) dots 6.33 – 19.0 mm (38 – 114 mm when [Power, general] Rechargeable battery pack NP-BD1 converted to a 35 mm still camera) F3.5 – 4.3 Exposure control: Automatic exposure, Scene Power: Rechargeable battery pack NP-BD1, 3.6 V Used battery: Lithium-ion battery Selection (1 0 modes) NP-FD1 (not supplied), 3.6 V Maximum voltage: DC 4.2 V White balance: Automatic, Daylight, Cloudy, AC-LS5K AC Adaptor (not supplied), 4.2 V Nominal voltage: DC 3.6 V Fluorescent 1, 2, 3, Incandescent, Flash Power consumption (during shooting): 1.0 W Capacity: 2.4 Wh (680 mAh) File format (DCF compliant): Operating temperature: 0 to 40 ºC (32 to 104 ºF) Still images: Exif Ver. 2.2 1 JPEG compliant, Storage temperature: –20 to +60 ºC (–4 to +140 ºF) Design and specifications are subject to change Dimensions: 90.0×56.4×20.7 mm (3 5/8× DPOF compatible without notice. Movies: MPEG1 compliant (Monaural) 2 1/4×27/32 inches) (W/H/D, excluding Recording media: Internal Memory (approx. protrusions) 31 MB), “Memory Stick Duo” Mass ( including NP-BD1 battery pack, paint pen Flash: Flash range (ISO sensitivity and strap etc.): Approx. 156 g (5.5 oz) (Recommended Exposure Microphone: Monaural Index) set to Auto): approx. 0.1 to 3.0 m Speaker: Monaural (4 inches to 9 feet 10 1/8 inches) (W)/ Exif Print: Compatible approx. 0.25 to 2.5 m (9 7/8 inches to PRINT Image Matching III: Compatible 8 feet 2 1/2 inches) (T) PictBridge: Compatible — 2 —,

Model information table

Model DSC-T70 DSC-T75 US, CND, AEP, UK, E, AUS, Destination AEP, UK, E, KR HK, CH, KR, AR, BR, J, JE HD Output Adaptor Cable • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model MX : Mexican model NE : North European model

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. FLEXIBLE Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, 1. SERVICE NOTE ENGLISH JAPANESE 1-1. PRECAUTION ON REPLACING THE SY-183 BOARD DESTINATION DATA When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”. USB SERIAL No. The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”. 1-2. SELF-DIAGNOSIS FUNCTION 1-2-1. Self-diagnosis Function 1-2-2. Self-diagnosis Display When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the LCD screen function starts working, and displays on the LCD screen what to shows a 4-digit display consisting of an alphabet and numbers, which do. blinks at 3.2 Hz. This 5-character display indicates the “repaired Details of the self-diagnosis functions are provided in the Instruction by:”, “block” in which the problem occurred, and “detailed code” manual. of the problem. LCD screen Blinks at 3.2 Hz

C3200

Repaired by: Block Detailed Code C : Corrected by customer Indicates the appropriate Refer to “1-2-3. Self-diagnosis Code Table”. E : Corrected by service step to be taken. engineer E.g. 13 ...Format the “Memory Stick Duo”. 32 ...Turn on power again. 1-1,

ENGLISH JAPANESE

1-2-3. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code The internal memory has experienced a Format the internal memory. format error. “Memory Stick Duo” is unformatted. Format the “Memory Stick Duo”. C1301“Memory Stick Duo” is broken. Insert a new “Memory Stick Duo”. “Memory Stick Duo” type error Insert a supported “Memory Stick Duo”. The camera cannot read or write data Turn the power off and on again, or taking out and inserting the on the “Memory Stick Duo”. “Memory Stick Duo” several times. C3201Trouble with hardware Turn the power off and on again. Retry turn the power on by the power switch. If it does not Difficult to adjust focus recover, check the focus reset sensor of lens block (pin ea ofE6100(Cannot initialize focus) CN401 on the SY-183 board). If it is OK, check the focus motor drive IC (IC401 on the SY-183 board). Retry turn the power on by the power switch. Check the zoom reset sensor of lens block (pin wk of CN401 on the SY-183 Zoom operations faultE6110board), if zooming is performed when the zoom button is (Cannot initialize zoom lens.) operated. If it is OK, check the zoom motor drive IC (IC401 on the SY-183 board). Check or replacement of the IC for steadyshot (IC503 on the SY- E6202Abnormality of IC for steadyshot. 183 board). Check or replacement of the IC for steadyshot (IC503 on the SY- E6210Lens initializing failure. 183 board). Check the HALL element (PITCH) of optical image stabilizer (pin 1, 2 of CN401 on the SY-183 board). If it is OK, checkE6211Lens overheating (PITCH). PITCH angular velocity sensor (SE502 on the SY-183 board) peripheral circuits. Check the HALL element (YAW) of optical image stabilizer (pin 6, 7 of CN401 on the SY-183 board). If it is OK, check YAWE6212Lens overheating (YAW). angular velocity sensor (SE501 on the SY-183 board) peripheral circuits. Check the OIS temp sensor of optical image stabilizer (pin 5 ofE6220Abnormality of thermistor. CN401 on the SY-183 board). E9101Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note) E9200Non-standard battery is used. Use the compatible battery only. Note: After repair, be sure to perform “1-3. PROCESS AFTER FIXING FLASH ERROR”. 1-3. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen. Method for Initializing the Flash Error Code Initialize Initializes the setting to the default setting. Even if you execute this function, the images stored in the internal memory are retained. 1 Touch [Initialize]. The message “Initialize all settings” appears. 2 Touch [OK]. The settings are reset to the default setting. To cancel the resetting Touch [Cancel] or [BACK] in step 2. • Make sure that the power is not disconnected during resetting. 1-2 Repaired by:,

ENGLISH JAPANESE

1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-183 board, erase the data in internal memory of the board before replacement. Method for Copying the Data in Internal Memory

Copy Copies all images in the internal memory to a “Memory Stick Duo”. 1 Insert a “Memory Stick Duo” with sufficient capacity. 2 Touch [Copy]. The message “All data internal memory will be copied” appears. 3 Touch [OK]. Copy starts. To cancel the copying Touch [Cancel] or [BACK] in step 3. • Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. • You cannot copy individual images. • The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in [ Inte rnal Memory Tool ]. • When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied. You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be copied. • Even if you copy data, a DPOF (Print order) mark is not copied.

Method for Formatting the Internal Memory

This item does not appear when a “Memory Stick Duo” is inserted in the camera. Format Formats the internal memory. • Note that formatting irrevocably erases all data in the internal memory, including even protected images. 1 Touch [Format]. The message “All data internal memory will be erased” appears. 2 Touch [OK]. The format is completed. To cancel the formatting Touch [Cancel] or [BACK] in step 2. 1-3,

ENGLISH JAPANESE

1-5. HOW TO WRITE DATA TO INTERNAL MEMORY Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change the setting, use the write enable tool “WriteEnableTool.exe”. Data writing method 1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”. 2) Start the Write Enable Tool and the SeusEX. 3) Click the [Activate Write Enable Mode] button of the Write Enable Tool. 4) Upon completion of the setting change, the following message will be displayed. 5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage). 6) Write the data read out into the PC to the internal memory of the camera. 7) Disconnect the PC from the camera, and turn off the camera. Note: By turning off the camera, the write enable setting is reset. 1-4, 1. SERVICE NOTE ENGLISH JAPANESE 1-1. SY-183基板交換時の注意 仕向けデータ 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 ADJ編を参照して,「DESTINATION DATA WRITE」を行ってください。

USBシリアルNo.

セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。 新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。 ADJ編を参照して,「USB SERIAL No. INPUT」を行ってください。 1-2. 自己診断機能 1-2-1. 自己診断機能について 1-2-2. 自己診断表示 本機の動作に不具合が生じたとき,自己診断機能が働き, 本機の動作に不具合が生じたとき,LCD画面にアルファベッLCD画面に,どう処置したらよいか判断できる表示を行い トと4桁の数字が表示され,3.2Hzで点滅します。この5文字 ます。自己診断機能については取扱説明書にも掲載されて の表示によって対応者分類および不具合の生じたブロックの います。 分類,不具合の詳細コードを示します。 LCD画面 C : 3 2 : 00 3.2Hz点滅

C3200

対応者分類 ブロック分類 詳細コード C :お客さま自身で対応 対応方法の違いにより分類 「1-2 -3 . 自己診断コード表」 E :サービスエンジニア 例 13 ・・ ・“ メモリースティック を参照 で対応 デュオ”をフォーマッ トする 32 ・・ ・電 源を入れ直す 1-5,

ENGLISH JAPANESE

1-2-3. 自己診断コード表 自己診断コード対応ブロック 詳細 症状/状態 対応/方法 者 機能 コード 内蔵メモリにフォーマットエラーが 内蔵メモリをフォーマットする。 あった。 フォーマットしていない“メモリー “メモリースティック デュオ”をフォーマットする。 スティック デュオ”を入れた。 C1301“メモリースティック デュオ”が 新しい“メモリースティック デュオ”に交換する。 壊れている。 “メモリースティック デュオ”の 規格内の“メモリースティック デュオ”を挿入する。 タイプエラーを検出した。 “メモリースティック デュオ”が 電源の入れ直し,または“メモリースティック デュオ” 読み/書きできない。 の挿し/外しを数回試す。 C3201ハードウェアトラブルを検出した。 電源を入れ直す。 E6100フォーカスが合いにくい。 操作スイッチの電源を入れ直す。 (フォーカスの初期化ができない) 復帰しない場合はレンズブロックのフォーカスリセットセ ンサ(SY-183基板CN401 eaピン)を点検する。異常なけ ればフォーカスモータ駆動IC(SY-183基板IC401)を点検 する。 E6110ズーム動作の異常。 操作スイッチの電源を入れ直す。 (ズームレンズの初期化ができな ズームボタンを操作したときにズーム動作をすればレンズ い) ブロックのズームリセットセンサ(SY-183基板CN401 wk ピン)を点検する。異常なければズームモータ駆動IC (SY-183基板IC401)を点検する。 E6202手振れ補正用ICの異常。 手振れ補正用IC(SY-183基板IC503)を点検または交換す る。 E6210手振れ補正用ICの異常。 手振れ補正用IC(SY-183基板IC503)を点検または交換す (レンズ初期化異常) る。 E6211レンズオーバーヒート(PITCH) 光学手振れ補正ブロックのホール素子(PITCH)(SY-183 基板CN401 1,2ピン)を点検する。異常なければ PITCH角速度センサ(SY-183基板SE502)周辺の回路を点 検する。 E6212レンズオーバーヒート(YAW) 光学手振れ補正ブロックのホール素子(YAW)(SY-183 基板CN401 6,7ピン)を点検する。異常なければYAW 角速度センサ(SY-183基板SE501)周辺の回路を点検す る。 E6220サーミスタの異常。 光学手振れ補正ブロックのサーミスタ(SY-183基板CN401 5ピン)を点検する。 E9101フラッシュの充電異常。 フラッシュユニットを点検または交換する。(Note) E9200規定外の充電池が使用された。 規定の充電池を使用する。 Note:交換後は,必ず「1-3. フラッシュ異常修理後の処置」を行って下さい。 1-6,

ENGLISH JAPANESE

1-3. フラッシュエラー発生時の対処法 本機はフラッシュエラー(自己診断コードE:91:01)が発生した場合,高電圧による異常を防止するために自動的にフラッシュ 充電および発光禁止の設定になります。 フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ り行います。 設定リセットお買い上げ時の設定に戻 し ます 。 [ 設 定リ セッ ト ] を実行しても 、 内 蔵メモリーに記録されている画像 は 削除されませ ん 。 1[設定リセット]をタッチする。 [全ての設定内容をリセットします]というメッセージが表示される。 2[実行]をタッチする。 設定リセットが実行される。 設定リセットを中止するには手順2で、[キャンセル]または[BACK]をタッチする。 設定リセット中は電源が切れないようにご注意ください。 1-4. 内蔵メモリのデータコピーおよび消去方法 内蔵メモリのデータコピーまたは消去はホーム画面の操作から実行可能です。(消去する場合は内蔵メモリの初期化を行いま す。)

Note1:SY-183基板交換の際は,基板交換前に内蔵メモリのデータを消去して下さい。

内蔵メモリのコピー方法 コピー 内蔵メモリーに記録した画像を、“メモリースティックデュオ”に一括コピーします。 1充分な空き容量のある“メモリースティックデュオ”を本体に入れる。 2[コピー]をタッチする。 「内蔵メモリーのデータがすべてコピーされます」というメッセージが表示される。 3[実行]をタッチする。 コピーが実行される。 コピーを中止するには 手順3で、[キャンセル]または[BACK]をタッチする。 • 充分に充電したバッテリーをご使用ください。残量の少ないバッテリーを使用して画像ファイ ルをコピーすると、バッテリー切れのため、データを転送できなかったり、データを破損するお それがあります。 • 画像ごとのコピーはできません。 • データをコピーしても、内蔵メモリー内のデータは削除されません。内蔵メモリーの内容を消 去するには、コピー後に“メモリースティック デュオ”を本体から取りはずし、[内蔵メモ リーツール]の[フォーマット]を行ってください。 • データのコピーをすると、“メモリースティックデュオ”内に新しいフォルダが作成されます。 コピー先のフォルダを指定することはできません。 • データのコピーを行っても、DPOF(プリント予約)マークの設定はコピーされません。 内蔵メモリのフォーマット方法 “メモリースティックデュオ ”が本機に入っている場合は表示されません。 フォーマット内蔵メモリーの管理領域をフォーマット( 初期化)します。 フ ォーマットすると、プロテクトし て ある 画 像も 含め て 、すべてのデータが消去され 、元に戻せません 。 1[フォーマット]をタッチする。 「 内蔵メモリーのデータがすべて消去されます」というメッセージが表示される。 2[実行]をタッチする。 フォ ー マッ ト を中止するに は 手順2で、[キャンセル]または[BACK]をタッチする。 1-7,

ENGLISH JAPANESE

1-5. 内蔵メモリへデータを書き戻す方法 通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。 基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。 設定の変更には,書き込み許可ツール(WriteEnableTool.exe)を使用します。 書き戻し方法 1) カメラとPCをマスストレージ接続し,ドライバを"Sony Seus USB Driver"に切り替える。 2) 書き込み許可ツールとSeusEXを起動する。 3) 書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。 4) 設定の変更が終了すると,次のメッセージが表示されます。 5) ドライバを元に戻して、カメラとPCをマスストレージ接続する。 6) PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。 7) カメラとPCの接続を解除し,カメラの電源をOFFにする。 注意: カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。 1-8E, 2. DISASSEMBLY

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some • When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside) • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE ST-172 BOARD’S CHARGING CAPACITORS (C901, C902)

The charging capacitors (C901, C902) of the ST-172 board is charged up to the maximum 315 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.

Preparing the Short Jig

To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. 1 kΩ/1 W Note: High-voltage cautions Discharging the Capacitor Wrap insulating tape. Short-circuit between the two points with the short jig about 10 seconds. To avoid the spark with the metal plate, wrap the short jig with the insulation tape. C902 C901 R:1 kΩ/1 W (Part code: 1-215-869-11) 2-1, 2-1. IDENTIFYING PARTS Cabinet (Rear) Assy Control Switch Block (RL60570) SY-183 Board MC-185 Flexible Board LCD Block Battery Holder Assy ⋅ BT-039 Flexible Board ⋅ ST-172 Flexible Board Cabinet (Front) Assy Lens Block ⋅ CD-710 Flexible Board - DISASSEMBLY FLOW - 2-2-1. OVERALL SECTION - Cabinet (Front) Assy - Cabinet (Rear) Assy - LCD Block 2-2-2. SY-183 BOARD SECTION - Lens Block - MC-185 Flexible Board - SY-183 Board 2-2-3. BATTERY HOLDER SECTION - Flash Block - BT-039 Flexible Board - Battery Holder Assy 2-2,

HELP

2-2. DISASSEMBLY

EXPLODED VIEW HARDWARE LIST

2-2-1. OVERALL SECTION Follow the disassembly in the numerical order given. 1Cabinet (Front) Assy (1-1 to 1-9) 2Cabinet (Rear) Assy (2-1 to 2-3) 3 LCD Block (3-1 to 3-4) 2 Cabinet (Rear)

Assy

1-2 1-4 (#18/#29) (Claws) 3 LCD Block 2-3 2-2 3-2 3-1 1-1 (#18/#29) 1-9 1-7 3-3 (#82) 1-6 2-1 1-8 (#18/#29) (Claws) 1-5 Note: High-voltage cautions 3-4 (Claws) Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds. 1-3 To avoid the spark with the metal plate, (#18/#29) 1 Cabinet (Front) wrap the short jig with the insulation tape.

Assy

C902 C901 R:1 kΩ/1 W (Part code: 1-215-869-11) 2-3, 2-2-2. SY-183 BOARD SECTION Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1 Lens Block (1-1 to 1-2) 2MC-185 Flexible Board (2-1 to 2-3) 3 SY-183 Board (3-1 to 3-3) 3-3 (Claw) 3 SY-183 Board 3-1 2-1 (#18/#29) 2-3 1-2 2-2 3-2 2 MC-185 HELP Flexible Board 1-1 1 Lens Block 2-4, 2-2-3. BATTERY HOLDER SECTION Follow the disassembly in the numerical order given. EXPLODED VIEW 1 Flash Block (1-1 to 1-7) 2 BT-039 Flexible Board (2-1) 3 Battery Holder Assy (3-1) 3 Battery Holder Assy 2 BT-039

Flexible Board

3-1 (Claw) 2-1 1-1 HELP (Claw) 1-2 (Claws) 1-7 1-3 (Claw) 1-4 1-5

Flash Block (Claw) (Claws)1

1-6 2-5E,

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. SHEET (SY) SY-183 board SHEET, ST2 MAIN FRAME

HELP

, 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2), 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

CD-710 FLEXIBLE BOARD SY-183 BOARD (1/2) LENS BLOCK

LCD901 LENS IRIS (1/3) (METER) CN301 CN709 10 CCD_OUT18 14 20 L7 CA_AD00 - CA_AD13 LCD_D0 - LCD_D7 IC002 IC001 HIGH POWER_SAVE CCD 23 J8SPEED IMAGER BUFFER E10 CA_HD AE23 LCD_CK, LCD_HD, LCD_VD CA_FD 3.0 inch H1 - H3 D11 AF22 COLOR ZOOM FOCUS IRIS J5 GEN_TG_CLK AF18 U19 XCS_ PANEL 4 LCDMOTOR MOTOR MOTOR IC211 XDD_SYS_RST MONITOR3

MMM27 8

LH1 L2 RG X201 (1/2) 20 2 L4 36MHz IC201 1 CPU IC_211_2_SO, XIC_211_2_SCKGEAR_ON V1, V2, V3A, V3B, V4, 2 CLOCK 3 Y13 (3/10, 4/10, 5/10)GENERATOR GEN_SYS_CLKV5A, V5B, V6 - V10 5 Y12(2/10) ZOOM FOCUS RESET RESET SENSOR SENSOR VST1, VST2 IC301 VHLD1, VHLD2 CCD SIGNAL PROCESS, E11 XDD_SYS_RST 31 12 LV C8 TIMING

CONTROL SWITCH

SUB GENERATOR1 24 G7 BLOCK (RL60570) SUB_CONT (6/10) 25 11 (1/2) XCS_FE, XIC_211_3_SCK, IC_211_3_SO CN710 Q302 F11 IC_211_2_SO, (1/2) XIC_211_2_SCK MIC_SIG VSUB_CONT_PRE, A3 1 Q301 VSUB_CONT_POST V8 XCS_AUDIO (MICROPHONE) D6

ST-172 FLEXIBLE

IC401 IC_211_AUINXLENS_DRIVER_PS AF8 A6 BORAD (1/2) LENS DRIVE D4 H11 CN701 (7/10) (1/2) IC_211_AUOUT IC601 SP SP SP901 AE8 B6 CN401 IRIS_DIR_A, IRIS_BRK_A, AUDIO/VIDEO (SPEAKER) IRIS_A, A, B, B IRIS_A, A, B, B IRIS MOTOR IRIS_DIR_B, IRIS_BRK_B AMP DRIVER (9/10) MC-185 FLEXIBLE

BOARD (1/2)

CN703 FOCUS_A, A, B, B FOCUS_A, A, B, B FOCUS (1/2) MOTOR FC_DIR_A, FC_DIR_B, FC_BRK_A AU_LINE_OUT A_LINE_OUT DRIVER E2 22 16 IC_211_CVOUT F3 F1 V_LINE_OUT V_OUT24 20 ZOOM_A, A, B, B ZOOM_A, A, B, B ZOOM MOTOR ZM_DIR_A, ZM_DIR_B, ZM_BRK_A DRIVER Q232 - Q234 Q231 AB13 IC_211_CVOUT IC_211_YOUT 27 HD_Y 24 AF12 VOUT_1 IC_211_PBOUT HD_PBFC_SENS FC_SENS FC_SENS BUFFER CLAMP 12 4 CN001 31 Y10 VOUT_2 IC_211_PROUT HD_PR (1/2) FC_SENS_GND XFC_RST_LED XFC_RST_LED AC12 11 233 M8 MULTI ZM_SENS 28 ZM_SENS_1ST ZM_SENS_1ST AD26 CONNECTOR ZM_SENS_GND 30 XZM_RST_LED XZM_RST_LED J8 XHD_ENV7 LENS TEMP LENS_TEMP LENS_TEMP LENS_TEMP SENSOR 27 AE3 USB_DP, USB_DM USB_DP, USB_DM

OPTICAL IMAGE STABILIZER OIS TEMP IC_401_TEMP 5 TZ_HALL_TEMP TZ_HALL_TEMP AF3 USB_VBUS USB_VBUSSENSOR 2 13 6

SE501 OVERALL (2/2) CN702 YAW M YAW SWAOUT YAW (PAGE 3-2) XMS_IN MOTOR J5 13 21 SENSOR

MEMORY STICK

YAW_HALLBIAS IC506 MSX_BS, MSX_D0 - MSX_D3, MSX_CLK

DUO

HALL YAW_HALL CLK, DATA PITCH/YAW ELEMENT SENSOR

AMP

(8/10) SE502 PITCH PITCH IC503M SWBOUT PITCHMOTOR OPTICAL G5 10 1 SENSOR

IMAGE

PITCH_HALLBIAS STABILIZATION CA_FD HALL PITCH_HALL DRIVE C9 ELEMENT (8/10) A7 XDD_SYS_RST A3 CLK_IC_503 W13 A6 XIC_211_IC_503_RST H10 A5 XCS_IC_503 U8 XDD_SYS_RST1A: VIDEO SIGNAL IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK OVERALL (2/2) A : AUDIO SIGNAL (PAGE 3-2) A : VIDEO/AUDIO SIGNAL 3-1 32, 33 16, 15 3 - 14 28 - 30 1, 2, 15, 16 9 - 12 3, 4, 6, 7 13, 17 22 - 25 18 - 21 36 - 39 J3, J2, H2, J4 B1, D1 G6, J8, J9, J7 B10, D10 1, 16 13, 14 38, 39 26 - 37 4 - 6 A4, B4, B5 D5, D6 24, 25 B4, B5, B3, A3 D6, E6, B7, C6 F2, E2, D2, B1 E6, E7 C5, B5 G9, F9, J9, F6, D1, D2, H1, F7, G5, E9, D9, H2, K1, K2 F5, C4, E5, D10 B10, B8, B9, C6, C7, A8, A7, A2, C3, C4, A1 D5, A6, B6, C5 F5, E5, D3, F1 K10, L10, K9 B7, B6, A6, A5, B4, A4, A3 AB23, AC26, AA23 W18, AB26, W17 W16, AD25, Y18, Y17 R7, AF25 V19, D19, C25 AB21, AC21, AB20, AC20, AB19, AC19, AC18, AE21, AF21, AE20, AF20, AE19, AF19, AE18 A13 - A15, D17, B19, E17, A19, B13 - B15 Y1, AA1 E18, B23 B18, D18, B17 E16, A18, D16, A17 E6, D5 A1, C1 2 - 5, 7, 8 16, 18 3, 4 5, 6 7 - 9 10 - 17 10, 12, 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-183 BOARD (2/2) MC-185 FLEXIBLE BOARD (2/2) CONTROL SWITCH BLOCK CN703

(RL60570) (2/2) XPWR_ON (2/2) 7 XPOWER_ONCN710 7 (2/2) S002 7 XPWR_ON XPWR_ON ACV_UNREG ACV_UNREG POWER D7 D001 S001 Q001, XAVC_DET BATT_XEXT 6 XDIRECT_PB XDIRECT_PB D9 Q002 10 19 CHARGE_V CHARGE_V S005 XAE_LOCK_SW9 (SHUTTER) XSHUT_SW8 S003 S004 IC001TWKEY_AD_1 DC/DC (ZOOM) CONVERTER (1/10) CN001 (2/2) D001 XPWR_LED MULTI (POWER) 4 CONNECTOR LCD901 (3/3) CN708 BL_H F9 BL_L E10

BACKLIGHT

BATT_SENS XACV_IN D002 2 XMS_IN F6 AE7 K8D10 XPWR_OFFC10 G8 XAV_JACK_IN XAV_JACK_IN XAV_JACK_IN

OVERALL (1/2) XIC_211_RST_REQ G9 28USB_VBUS D6 W12 UART_Rx, 26

(PAGE 3-1) E7 C9 XDD_SYS_RST AB18 IC_211_1_UI, IC_211_1_UO IC_211_1_UI, IC_211_1_UO UART_Tx K7 XCS_DD X001 C5 A23

ST-172 FLEXIBLE BOARD (2/2) 32.768kHz K6 LCD901CN707 (2/3)

T001 XAF_LED D001 C4 IC_211_0_SO, AB8 TOUCH_PANEL_X TOUCH_PANEL_YU XE_A(H) 4 1 ST_UNREG IC_211_0_SI, AF7 TOUCH_PANEL_Y TOUCH_PANEL_XLXIC_211_0_SCK 1

TOUCH

+ + TOUCH32PANEL TRIGGER R2 TOUCH_PANEL_SEL1 PANEL TOUCH_PANEL_YL FLASH I/F 5 UNIT TRIGGER_GND TOUCH_PANEL_SEL2 TOUCH_PANEL_XR C901 C902 CN701 T5 2 ( CCAHARGING)( CHARGING) (2/2) STRB_CHG Q706 - Q708 PACITOR CAPACITOR 15 IC001 10 9 XDD_SYS_RST XE_K(L) XSTRB_FULL 1FLASH 9 10 IC211 CONTROL, STB_CHG_CNT6 11 OVERALL (1/2) (2/2)

CHARGE

Q001 (PAGE 3-1) IC_211_0_SO,CONTROL STRB_ON1 CPU FLASH748IC_211_0_SI,XIC_211_0_SCK (3/10, 4/10, 5/10)DRIVE D701 XDD_SYS_RST D002 D706XAF_LED (MS ACCESS) H8AF illuminator/ 5 self-timer lamp XPWR_LED Y9 XAE_LOCK_SW N19 XSHUT_SW R19 KEY_AD_1 XCS_IC_202, BT-039 FLEXIBLE AC8 XIC_211_1_SCK, STRB_CHG BOARD V2 IC_211_1_SO, CN704 XSTRB_FULL IC_211_1_SI H9 CHARGE_V BATT_UNREG STB_CHG_CNT IC202 + H15 BATT_SIG BH001STRB_ON1 BATTERY E4 6 BATT_SIGY16 S BATTERYAUTHENTICATION (2/10) REG_GND BATT_GND ( T- E RBOMINAARD L ) XDD_SYS_RST B2 3-2 1, 2 5, 6 1, 2 C6 - C8 H17, A24, G17 W20, H18, B24, G18 D26, G19 B1, B5, C5, D5 1 - 5 7 - 10 8, 9 29 - 33 34 - 39 15, 9 17, 21 23, 25, 3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

MC-185 FLEXIBLE SY-183 BOARD (1/2) BOARD

F001 CN702 MS_VCC MEMORY 9 STICK CN703 DUO ACV_UNREG ACV_UNREG F002 L001 Q001, 002 IC001 BATT_XEXT XACV_DET CN001 19 10 DC/DC CONVERTER(1/10) ST-172 FLEXIBLE MULTI D001 CN701 BOARD (1/2) CONNECTOR D002 MS_PWR_OUT F3 (2/2) CHARGE_V CHARGE_V F003 L004 VL_3V 2 BT001 F10 DDCBL_LX LITHIUM R008 XPOWER_ON XPWR_ON RTCBAT H5 SECONDARY77BATTERY DDC5_LX_1 J3 XACV_IN DDC5_LX_2 K3 ST_UNREG D006 Q003 DDC5_VO_1 J2 M_5.0V BH001 DDC5_VO_2 K2 B+ SWITCH ( B A TTE

BT-039 FLEXIBLE

TERMIRY IC202NAL) BOARD LD03P1U_IN H4BATTERY IC002 BOARD CN704 AUTHENTICATION C DDC5_PSW H1 R005 (2/10) Q004 SHUTTER DOOR DETECT BATT_UNREG CHARGE_V POWER (2/2) B+ SWITCH (1/10)+ IC_211_1_SI D004 P144_SOA0 D5 (PAGE 3-4) XLV_ON EVER BATT_SIG BATT_SIG IC_211_1_SO XPWR_ON2 D8 2 OUT VDD1S6E4 TXRX P143_SIA0 C5 XIC_211_1_SCK BATT_GND REG_GND P142_XSCKA0 B5 - XCS_IC_202 LD03P1E_OUT F5 P120_INTP0 B1 L009 D_1.8V D_3.0V DDC1P8_LX A8 B2 XRESET DDC1P8_VFB B6 L008 D_1.2V DDC1P2_LX A4 DDC1P2_VFB B2

A EXDD_SYS_RST XDD_SYS_RST

C9 XSYS_RST DDC12_LX_1 J9 D007 CAM_13V POWER (2/2) DDC12_LX_2 K9 POWER (2/2) DDC12_PWR_OUT_1 J8 L002 Q005(PAGE 3-4) (PAGE 3-4) DDC12_PWR_OUT_2 K8 3.0V/1.8VDISCHARGE DDC12_VFB H8

B XIC_211_RST_REQ XIC_211_RST_REQ D6 XRESET_REQ D008 CAM_-7.5V

XPWR_OFF XPWR_OFF DDCM7P5_LX J10 POWER (2/2) C10 XPWR_OFF DDCM7P5_VFB F8

CONTROL SWITCH (PAGE 3-4) CAM_3.5VLD03P4_OUT H3 USB_3.1V BLOCK (RL60570) JD03P1U_OUT J5

CN710 D_1.5VLD01P5_OUT A6 DDR_1.8V D001 D_3.0V LD01P8_OUT A75 BL_H (POWER) DDCBL_VO F9 BL_L S002 DDCBL_VL E10 XPWR_ON XPWR_ON POWER 7 D7 XPWR_ON1 DDC2P9_VO_1 F1 D_3.0V DDC2P9_VO_2 F2 L006 S001 A_3.0VDDC2P9_VFB G1 XDIRECT_PB XDIRECT_PB 6 D9 XPWR_ON3 MS_PWR_ON D MS_PWR_ON G3 POWER (2/2) (PAGE 3-4) 3-3 17, 21 23, 25 1-5 7-10 29 - 33 34 - 39, 3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-183 BOARD (2/2) IC507

2.8V REG (8/10) IC506 LCD901 A_3.0V IC_503_2.8V PITCH/YAW CN709 4 VDD VOUT 3 SENSOR AMP D_1.8V L702 VDDL CE (8/10) 22 D_3.0V L701 VDD SE502 23 3.0 inch

COLOR

D_1.8V PITCHSENSOR XDD_SYS_RST XRESET 3 LCD MONITOR IC503 D_1.5V D_1.5V OPTICAL SE501 D_3.0V IMAGE YAW M_5.0V STABILIZATION SENSORDRIVE (8/10)

A CN708XDD_SYS_RST

A7 RESET_N BL_H BL_H POWER (1/2) XIC_211_IC_503_RST A6 XDL (PAGE 3-3) BL_L BL_L ST_UNREG XDD_SYS_RST LCD CAM_13V BACKLIGHT CAM_-7.5V BL_H BL_L A_3.0V D_1.8V D_1.8V CN701 ST-172 FLEXIBLE BOARD (2/2) T001 D_3.0V D_3.0V D_3.0V Q709,710 (2/2) ST_UNREG ST_UNREG L001 D001 B+ SWITCH FLASH M_5.0V M_5.0V M_5.0V UNIT CAM_3.5V D_1.8V L602 M_5.0V IC601 7D_3.0V AU_AVCC AUDIO/VIDEO 6 D002 D_3.0V AMP AF illuminator/ (9/10) H10 GPE_09 self-timer lamp AB18 XRESET R712 D706 L601 AU_AVCC (MS ACCESS) IC001 A_3.0V FLASH CONTROL, R252 IC201 CHARGE CONTROL R253 D_1.8V

E CLOCKL231 GENERATOR

POWER (1/2) D_3.0V (2/10) (PAGE 3-3) D_1.8V ST_UNREG_ONGPS_13 W7 FB292 CD-710 FLEXIBLE

BOARD

FB293 IC211 CN301 CPU CAM_13V L303 CAM_13V R255 (3/10) 16 IC001 (4/10) D_1.2V D_1.2V (5/10) CCD IMAGER DDR_1.8V DDR_1.8V CAM_-7.5V L302 CAM_-7.5V USB_3.1V L211 C355 FB301 FB308 Q303 -7.5V DISCHARGE IC002 CAM_3.5V HIGH SPEED

B XIC_211_RST_REQ W12 XRESET_REQ D_1.8V FB303 BUFFER AMP

XPWR_OFF POWER (1/2) G8 GPE_00 FB306 (PAGE 3-3) XACV_IN D_3.0V FB302 K8 GPE_05

C IC_211_1_SI IC303 2.3V REGG18 SIO1_RXD (6/10)

IC_211_1_SO POWER (1/2) B24 SIO1_TXDXIC_211_1_SCK LDO_2.3V (PAGE 3-3) H18 SIO1_SCK 4 VDD VOUT 3 XCS_IC_202 W20 GPS_04 IC301

D MS_PWR_ON CCD SIGNAL

T7 GPE_15 FE_1.8V PROCESS, POWER (1/2) 6 Vin Vout 4 TIMING GENERATOR (PAGE 3-3) (6/10) IC304 1.8V REG LENS BLOCK EVER EVER (6/10) CN401 R405 ZM_SENS_VCC ZOOM 29 RESET

SENSOR

Q305 3.0V/3.5V R404 FC_SENS_VCC FOCUS XDD_SYS_RST DISCHARGE 32 RESET E11 RSTB SENSORIC401 D_3.0V LENS DRIVE, M_5.0V IRIS MOTOR DRIVER, FOCUS MOTOR DRIVER, ZOOM MOTOR DRIVER (7/10) 3-4E12 - 15 5, 6 1, 2, 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM SP901 (SPEAKER) D002 ( AFilluminator/self-timer lamp ) FLASH UNIT BT001 C901 ST-172 FLEXIBLE ( LITHIUMSECONDARY) (CHARGING CAPACITOR) BOARD BATTERY C902 (CHARGING CAPACITOR) + BH001 (BATTERY TERMINAL) CONTROL SWITCH BLOCK10 (RL60570) S BT-039 FLEXIBLE

BOARD

1 19 1 - CN704 CN710 12 11 LCD901 10 1 12 1 LEVEL3 SY-183 BOARD LEVEL3 (SIDE B) BACKLIGHT SY-183 BOARD (SIDE A) 1 10 3.0 inch IC211 COLOR (Not supplied) LCD MONITOR LENS BLOCK

TOUCH PANEL

2 38 CN702 1 CN703 39 ( M EC MONORN YE SC T TR I CO K ) 11 12 39 1 MC-185 FLEXIBLE 39 1

BOARD

IC001 28 26 2 27 LEVEL3 (Not supplied) 25 1 CD-710 FLEXIBLE

BOARD

CN001 (MULTI CONNECTOR) 4-1 FRAME CN707 CN709 CN708 4516144261218 1 19 CN701 2 38 1 CN301 39 2 38 1 CN401 39, 4-2. SCHEMATIC DIAGRAMS

Link

MC-185 FLEXIBLE BOARD CONTROL SWITCH BLOCK (MULTI CONNECTOR) (RL60570) BT-039 FLEXIBLE BOARD ST-172 FLEXIBLE BOARD (BATTERY IN) (FLASH DRIVE) COMMON NOTE FOR SCHEMATIC DIAGRAMS, 4-2. SCHEMATIC DIAGRAMS 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ Pattern box µF. 50 V or less are not indicated except for electrolytics Color bar chart and tantalums. Pattern box PTB-450 For PTB-450: • Chip resistors are 1/10 W unless otherwise noted. J-6082-200-A J-6020-250-A or kΩ=1000 Ω, MΩ=1000 kΩ. Small pattern box For PTB-1450: • Caution when replacing chip parts. PTB-1450 J-6082-559-A New parts must be attached after removal of chip. J-6082-557-A Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. L = 24 cm (PTB-450) • Some chip part will be indicated as follows. L = 11 cm (PTB-1450) Example C541 L452 22U 10UH Pattern box Front of the lens TA A 2520 L Camera Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. 2. Adjust the distance so that the output waveform of • Parts with ★ differ according to the model/destination. Fig. a and the Fig. b can be obtain. Refer to the mount table for each function.

H

• All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C : panel designation • A : B+ Line • B : B– LineABA=BBA• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform) • C : adjustment for repair. • A : not use circuit (Measuring conditions voltage and waveform) Electronic beam scanning frame • Voltages and waveforms are measured between the measurement points and ground when camera shoots CRT picture frame color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Fig.b (Picture on monitor TV) Precautions for Replacement of Imager When indicating parts by reference number, please • If the imager has been replaced, carry out all the adjustments include the board name. for the camera section. The components identified by mark 0 or dotted line with • As the imager may be damaged by static electricity from mark 0 are critical for safety. its structure, handle it carefully like for the MOS IC. Replace only with part number specified. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4-2 Yellow Cyan Green White Magenta Red Blue, Schematic diagrams of the CD-710 flexible board and the SY-183 board are not shown. Pages from 4-3 to 4-13 are not shown., 12345678

A A

Pin 1 LND001 ACV_GND 2 LND002 ACV_GND 3 LND003 ACV_GND LND004 ACV_GND

Note:CN001(MULTI CONNECTOR) is not suppl ied, but th is is

LND005 ACV_GND LND006 ACV_GND inc luded in MC-185 f lex ib le complete board. XPOWER_ON LND007 XPOWER_ON

B LND008 UART_Tx UART_TX B

UART_RX LND009 UART_Rx BATT/XEXT LND010 BATT/XEXT LND011 HD_Pr LND012 HD_Pb LND013 USB_VBUS LND014 USB_GND LND040 LND015 USB_GND STATIC_GND LND016 USB_DP LND017 N.C.

SY-183 LND018 USB_DM CN001 26P

(10/10) LND019 USB_GND ( MULTICONNECTOR) CN703 HD_PR

C PAGE 4-13 LND020 USB_GND 2 HD_Pr ACV_GND 1 C

of LEVEL3 HD_PBLND021 USB_GND 4 HD_Pb ACV_GND 3 USB_VBUS LND022 AU_LINE_OUT 6 USB_VBUS ACV_GND 5 LND023 A_GND 8 USB_GND XPOWER_ON 7 USB_DP LND024 V_LINE_OUT 10 USB_DP UART_Tx 9 USB_DM LND025 V_GND 12 USB_DM LND026 V_GND 14 USB_GND HD_Y A_LINE_OUT LND027 HD_Y 16 A_OUT_L UART_Rx 15 LND028 XAV_JACK_IN 18 A_GND CHARGE_V 17 LND029 CHARGE_V V_OUT 20 V_OUT BATT_XEXT 19 LND030 CHARGE_V 22 V_GND CHARGE_V 21 LND031 CHARGE_V 24 HD_Y ACV_UNREG 23 CHARGE_V XAV_JACK_INLND032 26 XAV_JACK_IN ACV_UNREG 25

D LND033 CHARGE_V D

LND034 ACV_UNREG LND035 ACV_UNREG ACV_UNREG CHARGE_VLND036 37 ACV_UNREG ACV_UNREGLND037 38 LND038 ACV_UNREG 39 LND039 ACV_UNREG

E E F MC-185 FLEXIBLE BOARD F MULTI CONNECTOR

4-14 MC-185, • Refer to page 4-2 for mark 0. 12341234

AAAA

Pin 1 LND001 BATT_GND Pin CL001 2 LND002 BATT_GND 1 LND001 MIC_SIG CL002 (MICROPHONE) 3 LND003 BATT_GND 2 LND002 MIC_GND

SY-183 LND004 BATT_GND 3 LND003 REG_GND

(10/10) LND011LND005 BATT_GNDBATT_GND BATT_GND LND004 XPWR_LED D001 S001 CN704 LND012 LND006 BATT_SIG BATT_SIG BATT_SIG s BH001 SY-183 LND005 D_3.0V SML-412MWT86PAGE 4-13 BATTERY (POWER) of LEVEL3 LND007 BATT_UNREG BATT_UNREG LND013 BATT_UNREG TERMINAL (10/10) LND006 DIRECT_PBBOARD CN710 LND007 XPWR_ON S0028 LND008 BATT_UNREG

BBBPAGE 4-13 POWER9 of LEVEL3LND009 BATT_UNREG LND008 XSHUTTER_SW B

10 LND010 BATT_UNREG LND009 XAE_LOCK_SW Note: BH001 is not inc luded in S005 BT-039 f lex ib le complete board. 10 LND010 KEY_AD1 (SHUTTER) 11 LND011 REG_GND3NO112 LND012 REG_GND24R001

CCCC

S003 S004

BT-039 FLEXIBLE BOARD32TWD002 D005

(TL3SONY) (TL3SONY) (ZOOM)

BATTERY IN 1

08 LND021 STATIC_GND D003 D004 (TL3SONY) MAZW068H0LS0

D D E E CONTROL SWITCH BLOCK F (RL60570) F CONTROL SWITCH BLOCK(RL60570) is rep laced as b lock,

so that PRINTED WIRING BOARD is omit ted. 4-15 BT-039, RL60570, • Refer to page 4-2 for mark 0. 12345678Pin 1 LND001 REG_GND BT001

A R008 332 LND002 VL_3V LITHIUM SECONDARY ABATTERY

LND020 3 LND003 SP+ SPEKER+ SP901LND021 ( SPEAKER) LND004 SP- SPEAKER- D00243DOR5352 LND005 XAF_LED52AFilluminator /self- t imer lamp LND006 AF_ANODE61LND007 M_5V

SY-183 LND008 STRB_ON

(10/10) LND009 STRB_CHG CN701 LND010 PAGE 4-13 XSTRB_FULL 2518 LND030 of LEVEL3 2.2uH T001 D001 LND011 STRB_CHG_CONT L001 FT02P80TP + LND028 LND012 ST_UNREG14XE_A(H)

B LND013 ST_UNREG R007 C007 B4700 50V R004C+ C+

LND014 ST_UNREG C001 1/10W B 1M 22u 1608 220p23LND022 LND024 2012 LND026 LND015 ST_UNREG 6.3V C902 C901 2012 21.9u 21.9u LND031 TRIGGER LND016 REG_GND C 315V 315V FLASH 17 CHARGING CHARGING - TRIG_GND UNIT LND017 REG_GND D003 CAPACITOR LND023 CAPACITOR LND025 C004 RB520S-40TE61 0.033u LND027 18 LND018 REG_GND C- C- LND029 19 LND019 REG_GND 260.0 XE_K(L) 5162Q00173TIG030TS-S-TL-E084FLASHDRIVER002 1M

C 17 16 15 14 13 C

R003 C002 1u C005 B 3.7 PGND XX 10V SW 3.7 SW IC001

PGND

5.0 TPS65552RGTR0FLASHCONTROL, CHG VCCCHARGECONTROL03.1

XFULL

F_ON

D D

5678CL001

E E ST-172 FLEXIBLE BOARD F FLASH DRIVE F XX MARK:NO MOUNT NO MARK:REC/PB MODE

4-16 ST-1724321N.C HGND I_PEAK N.C 0 3.7 G_IGBT VBATT N.C N.C N.C 9 10 11 12, 4-3. PRINTED WIRING BOARDS Link MC-185 FLEXIBLE BOARD ST-172 FLEXIBLE BOARD BT-039 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS, 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 1221324334654456• Circled numbers refer to waveforms. • There are a few cases that the part printed on diagram543345411221123321isn’t mounted in this model. 3 2 • C: panel designation414-17, Printed wiring boards of the CD-710 flexible board and the SY-183 board are not shown. Pages 4-18 and 4-20 are not shown.,

MC-185 (2 layers), BT-039 (1 layer), ST-172 (2 layers)

: Uses unleaded solder.

MC-185 FLEXIBLE BOARD

SP901 LND020 (SPEAKER)

ST-172 FLEXIBLE BOARD

26 2 1-874-893- 11 D002 ( AF illuminator/ LND02128 25 1 27self- t imerlamp) R003 CN001 (MULTI CONNECTOR) 12 9 13 8 IC001 Note : CN001 (MULTI CONNECTOR) is not supplied, 16 5 1-874-892- 1114but this is included in MC-185 flexible complete board. LND031 D003 C007 C002 FLASH UNIT12- + BT001 ( LITHIUMSECONBATTERYDARY)T001 LND026 LND025 LND02943C901 ( CHARGING LND027 ACAPACITOR) LND024

CAUTION

K Danger of explosion if battery is incorrectly replaced. C902 Replace only with the same or equivalent type.LND023 ( CCAHPARGINGACITOR) LND030 LND022

BT-039 FLEXIBLE BOARD

+ LND013 BH001 ( BATTERY) LND012 LND010TERMINAL S LND009LND008LND007 BOARD LND006LND005 LND004 LND003 LND002 LND001 LND011 - 1-874-894- 11 Note: BH001 is not included in BT-039 flexible complete board. 4-21E MC-185, BT-039, ST-172 LND039 LND038LND037 LND036LND035 LND034LND033 LND032LND031 LND030LND029 LND028LND027 LND026LND025 LND024LND023 LND022LND021 LND020LND019 LND018LND017 LND016LND015 LND014LND013 LND012LND011 LND010LND009 LND008LND007 LND006LND005 LND004LND003 LND002LND001 LND040 C00441654R004 Q00158123LND028 R002 D001 R007 C001 L001 LND019 LND017 LND018 LND015 LND016 LND013 LND014 LND011 LND012 LND009 LND010 CL001 LND007 LND008 R008 LND005 LND006 C005 LND003 LND004 LND001 LND002 BT001,

NOTE

5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCOVERALL SECTION SY-183 BOARD SECTION BATTERY HOLDER SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

BT-039 FLEXIBLE BOARD C ST-172 FLEXIBLE BOARD C MC-185 FLEXIBLE BOARD B, 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant le numéro spécifié. uF: µF • COILS uH: µH • RESISTORS • Color Indication of Appearance Parts All resistors are in ohms. Example: METAL: metal-film resistor (SILVER) : Cabinet’s Color METAL OXIDE: Metal Oxide-film resistor (Silver) : Parts Color F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model 5-1, 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS DISASSEMBLY HARDWARE LIST 5-1-1. OVERALL SECTION ns: not supplied #18/#2956SY-183 board section LCD901 (See Page 5-3) #18 8 #29 (6.5mm × 6.5mm) 3 #82 #18 #29 ns (6mm × 14.5mm) #18/#29 CAUTION 1 : For the part of 7 : CUSHION (RL MICROPHONE) (3-275-797-01), cut NON WOVEN (T0.25) (3-076-631-01) into the desired length and use it. CAUTION 2 : For the part of 8 : SHEET (WATERPROOF SHEET) (3-280-761-01), cut NON WOVEN (T0.25) (3-076-631-01) into the desired length and use it. Ref. No. Part No. Description Ref. No. Part No. Description 1 3-272-252-01 GRIP 6 3-272-253-21 CABINET (REAR (SKK)) (WHITE) 2 A-1284-139-A CABINET (FRONT) BLOCK ASSY (SILVER) 6 3-272-253-31 CABINET (REAR (SKK)) (PINK) 2 A-1284-140-A CABINET (FRONT) BLOCK ASSY (BLACK) 7 CAUTION 1 CUSHION (RL MICROPHONE) 2 A-1284-141-A CABINET (FRONT) BLOCK ASSY (WHITE) 8 CAUTION 2 SHEET (WATERPROOF SHEET) 2 A-1284-142-A CABINET (FRONT) BLOCK ASSY (PINK) LCD901 A-1334-750-A FTS BLOCK ASSY (30SHGU07) 3 1-480-344-11 SWITCH BLOCK, CONTROL (RL60570) 4 3-272-254-01 BRACKET, STRAP #18 2-635-591-21 SCREW (M1.4), NEW TRUSTAR P2 (Silver) * 5 3-272-255-01 SHEET (STRAP), ADHESIVE #29 2-662-396-01 SCREW (M1.4), NEW, TRUSTAR, P2 (Black) 6 3-272-253-01 CABINET (REAR (SKK)) (SILVER) #82 3-272-251-01 SCREW (M1.4), HEAD PRECISION (Silver) 6 3-274-562-11 CABINET (REAR) (BLACK) 5-2, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

5-1-2. SY-183 BOARD SECTION Battery Holder section (See Page 5-4) SY-183 #18 #29 52 57 59 51 58 #30 (including IC001(CCD imager) and CD-710 flexible complete board.) (Note) Note : Be sure to read "Precuations for Replacement of Imager" on page 4-2. Ref. No. Part No. Description Ref. No. Part No. Description 51 3-272-209-01 SHEET (SY) 58 A-1284-148-A CCD BLOCK ASSY (including IC001 (CCD imager) * 52 3-272-205-01 MULTI (2), PLATE and CD-710 flexible complete board.) (Note) 53 A-1334-225-A MC-185 FLEXIBLE BOARD, COMPLETE * 59 3-272-428-01 SHEET, ELECTROSTATIC * 54 3-272-204-01 MULTI (1), PLATE 55 A-1364-520-A SY-183 BOARD, COMPLETE (SERVICE) #18 2-635-591-21 SCREW (M1.4), NEW TRUSTAR P2 (Silver) #29 2-662-396-01 SCREW (M1.4), NEW, TRUSTAR, P2 (Black) 56 3-272-203-01 SCREW, TRIPOD #30 3-086-156-11 SCREW B1.2 (White) 57 A-1167-020-B LSV-1110A (SERVICE USE) 5-3, 5. REPAIR PARTS LIST

DISASSEMBLY

5-1-3. BATTERY HOLDER SECTION (6mm × 25mm) BH001 101 113 ns 114 SP901 111 C902 BT001 C901 : BT001 (BATTERY, LITHIUM SECONDARY) 109 Board on the mount position. 107 (See page 4-21.) CAUTION 1 : CAUTION For the part of 104 : SHEET (RL) (3-272-219-01), Danger of explosion if battery is incorrectly replaced. cut SHEET, ADHESIVE (2-649-300-01) into the desired length and use it. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description 101 1-874-894-11 BT-039 FLEXIBLE BOARD * 109 3-272-210-01 SHEET, MCON 102 X-2186-608-1 ASSY, BTH (S) (SILVER) 110 3-272-213-01 FILM, ST 102 X-2186-609-1 ASSY, BTH (B) (BLACK) 0111 1-480-416-11 FLASH UNIT (FL60570) 102 X-2186-610-1 ASSY, BTH (W) (WHITE) 112 A-1334-226-A ST-172 FLEXIBLE BOARD, COMPLETE 102 X-2186-611-1 ASSY, BTH (P) (PINK) * 113 3-272-208-01 CUSHION, AF * 103 3-272-216-01 SHEET, ST2 * 114 3-272-207-01 CUSHION, SP 104 CAUTION 1 SHEET (RL) * 105 3-272-217-01 CUSHION (MICROPHONE) *0BT001 1-756-566-11 BATTERY, LITHIUM SECONDARY 106 X-2186-606-1 FRAME ASSY, MAIN 0BH001 1-780-456-41 TERMINAL BOARD, BATTERY 107 3-272-206-01 HOLDER, LENS *0C901 1-114-572-11 CAP, ELECT 21.9MF 315V *0C902 1-114-572-11 CAP, ELECT 21.9MF 315V * 108 3-272-218-01 SHEET, LH * SP901 1-826-759-11 BUZZER, PIEZOELECTRIC (2.0CM) 5-4,

BT-039

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description 1-874-894-11 BT-039 FLEXIBLE BOARD ******************** (BH001 is not included in BT-039 flexible complete board.) < BATTERY TERMINAL BOARD > 0BH001 1-780-456-41 TERMINAL BOARD, BATTERY ************************************************************

Electrical parts list of the CD-710 flexible

board is not shown.

Pages 5-6 is not shown.

• Refer to page 5-1 for mark 0. 5-5,

MC-185 ST-172

Ref. No. Part No. Description Ref. No. Part No. Description A-1334-225-A MC-185 FLEXIBLE BOARD, COMPLETE ******************************* (CN001 (MULTI CONNECTOR) is not supplied, but this is included in MC-185 flexible complete board.) < CONNECTOR > CN001 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) (MULTI CONNECTOR) ************************************************************ A-1334-226-A ST-172 FLEXIBLE BOARD, COMPLETE ****************************** 0 1-480-416-11 FLASH UNIT (FL60570) < LITHIUM BATTERY SECONDARY > *0BT001 1-756-566-11 BATTERY, LITHIUM SECONDARY < CAPACITOR > C001 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V C002 1-165-908-11 CERAMIC CHIP 1uF 10% 10V * C004 1-112-832-21 CERAMIC CHIP 0.033uF 10% 250V C007 1-164-933-11 CERAMIC CHIP 220PF 10% 50V *0C901 1-114-572-11 CAP, ELECT 21.9uF 315V *0C902 1-114-572-11 CAP, ELECT 21.9uF 315V < DIODE > 0D001 6-501-141-01 DIODE FT02P80TP * D002 6-501-364-01 DIODE DOR5352 (AF illuminator/self-timer lamp) D003 6-500-619-01 DIODE RB520S-40TE61 < IC > IC001 6-707-555-01 IC TPS65552RGTR < COIL > * L001 1-400-820-11 INDUCTOR 2.2uH < TRANSISTOR > *0Q001 6-551-686-01 TRANSISTOR TIG030TS-S-TL-E < RESISTOR > R002 1-218-989-11 RES-CHIP 1M 5% 1/16W R003 1-218-941-11 RES-CHIP 100 5% 1/16W R004 1-216-121-00 RES-CHIP 1M 5% 1/10W R007 1-216-829-11 METAL CHIP 4.7K 5% 1/10W R008 1-218-935-11 RES-CHIP 33 5% 1/16W < SPEAKER > * SP901 1-826-759-11 BUZZER, PIEZOELECTRIC (2.0CM) Electrical parts list of the SY-183 board is not shown. < TRANSFORMER > Pages 5-8 to 5-11 are not shown. 0T001 1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER ************************************************************ CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. 5-7,

Checking supplied accessories.

Note 1: This item is supplied with the unit as an accessory, but is not prepared as a service part. Power cord (mains lead) Conversion (2P) Adaptor Conversion (2P) Adaptor Adaptor plate USB, A/V cable for (EXCEPT US, CND, BR, J) 0 1-569-007-12 (JE) 0 1-569-008-12 (E) (HD1-A) multi-use terminal 0 1-823-947-71 (KR) 3-274-257-01 1-834-813-11 0 1-827-826-41 (AEP, E) 0 1-827-945-61 (AUS) 0 1-828-050-31 (JE) 0 1-832-106-31 (AR) 0 1-832-121-31 (CH) 0 1-832-169-31 (UK, HK) Rechargeable battery pack (NP-BD1) 0 A-1336-393-A (J) Instruction Manual 0 A-1336-394-A (US, CND) 3-219-483-01 (JAPANESE) (J) 0 A-1336-395-A (EXCEPT CND, US, J) 3-219-483-11 (ENGLISH) (CND, AEP, UK, AUS, E, HK, JE) 3-219-483-21 (FRENCH, ITALIAN) (CND, AEP) 3-219-483-31 (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 3-219-483-41 (GERMAN, DUTCH) (AEP) Battery charger 3-219-483-51 (TRADITIONAL CHINESE, (BC-CSD) SIMPLIFIED CHINESE) (E, HK, JE) 0 1-480-352-11 (J) Battery case 3-219-483-61 (RUSSIAN, UKRAINIAN) (AEP)0 1-480-352-21 (US, CND) 3-219-483-71 (ARABIC, PERSIAN) (E) 0 1-480-352-31 (Note 1) 3-219-483-81 (KOREAN) (KR, JE) (EXCEPT CND, US, J) 3-219-483-91 (POLISH, CZECH) (AEP) 3-219-484-11 (HUNGARIAN, SLOVAK) (AEP) 3-219-484-21 (SWEDISH, FINNISH) (AEP) Wrist strap 3-219-484-31 (NORWEGIAN, DANISH) (AEP) 2-050-981-01 (Gray) 3-219-484-41 (THAI, MALAY) (E) Paint pen (SILVER/WHITE/PINK Models) 3-219-484-51 (TURKISH, GREEK) (AEP) 2-888-952-01 (Black) (BLACK Model) 2-050-981-11 (Black) (BLACK Model) 3-219-484-61 (ENGLISH, SPANISH) (US) 2-888-952-11 (Gray) 3-219-484-72 (SIMPLIFIED CHINESE) (CH) (SILVER/WHITE/PINK Models) HD Output Adaptor Cable (DSC-T75 only) Cyber-shot Handbook (PDF) 1-833-859-21 The CD-ROM supplied contains all of language version of the Instruction Manual in pdf (Cyber-shot Handbook.pdf) for printing. The printed matter is not supplied. If required, please order it with the part number below. (Only for destination Japanese model) CD-ROM (Cyber-shot application software / 日本国内については日本語のみが印刷での部品供給可能です。 "Cyber-shot Handbook" / "Cyber-shot Step-up Guide") 3-219-480-01 (JAPANESE) 3-219-481-51 (POLISH) 3-219-478-01 (EXCEPT J) 3-219-480-11 (ENGLISH) 3-219-481-61 (CZECH) 3-271-036-01 (J) 3-219-480-21 (FRENCH) 3-219-481-71 (HUNGARIAN) 3-219-480-31 (ITALIAN) 3-219-481-81 (SLOVAK) 3-219-480-41 (SPANISH) 3-219-481-91 (SWEDISH) 3-219-480-51 (PORTUGUESE) 3-219-482-11 (FINNISH) 3-219-480-61 (GERMAN) 3-219-482-21 (NORWEGIAN) 3-219-480-71 (DUTCH) 3-219-482-31 (DANISH) 3-219-480-81 (TRADITIONAL CHINESE) 3-219-482-41 (THAI) 3-219-480-91 (SIMPLIFIED CHINESE) 3-219-482-51 (MALAY) 3-219-481-11 (RUSSIAN) 3-219-482-61 (TURKISH) 3-219-481-21 (ARABIC) 3-219-482-71 (GREEK) 3-219-481-31 (PERSIAN) 3-219-482-81 (UKRAINIAN) 3-219-481-41 (KOREAN) • Refer to the page 5-1 for mark 0. 5-12E,

HARDWARE LIST (1/5)

#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 1.7 1.7 1.7 1.4 2.5 4.0 2.5 2.5 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver) (Black) (Silver) 3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01 1.7 1.4 1.7 1.7 3.5 1.7 1.6 3.5 #9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping) (Silver) (Silver) (Silver) (Black) 3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21 1.7 1.7 1.7 1.7 5.0 4.0 4.0 5.0 #13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5 (Silver) (Silver) (Silver) (Silver) 3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01 1.7 1.7 1.4 1.4 2.5 2.5 1.5 2.5 #17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0 (Silver) (Silver) (Red) (Silver) 2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31 1.7 2.2 1.4 1.2 1.4 1.5 2.5 4.0 3.0 3.5,

HARDWARE LIST (2/5)

#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 1.4 1.7 1.7 1.7 3.0 5.0 4.0 5.5 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver) (Black) (Dark Silver) 2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61 1.7 1.4 1.4 1.4 3.0 2.0 2.0 4.0 #29: M1.4 X 2.5 #30: M1.2 X 4.0 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping) (Black) (White) (Silver) (Silver) 2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01 1.4 1.2 3.0 2.0 2.5 3.5 4.0 4.5 #33: M3.0 X 6.0 #34: M3.0 X 8.0 #35: M4.0 X 6.0 (Tapping) #36: M3.0 X 6.0 (Silver) (Black) (Silver) (Silver) 3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11 3.0 3.0 4.0 3.0 6.0 8.0 6.0 6.0 #37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping) (Black) (Silver) (Black) (Silver) 3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04 3.0 2.0 2.6 2.0 20.0 6.0 5.0 4.0,

HARDWARE LIST (3/5)

#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping) (Silver) (Silver) (Red) (Silver) 3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61 3.0 2.0 1.7 1.7 8.0 4.0 4.0 3.0 #45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5 (Silver) (Red) (Silver) (Silver) 2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91 1.4 1.7 1.4 1.7 2.5 3.0 3.0 2.5 #49: M2.0 X 4.0 #50: M2.0 X 3.0 #51: M2.0 X 2.5 #52: M2.0 X 4.0 (Tapping) (Black) (Red) (Silver) (Black) 2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11 2.0 2.0 2.0 2.0 4.0 3.0 4.0 2.5 #53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5 (Black) (Black) (Silver) (Silver) 3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11 2.0 1.75 2.0 2.0 5.0 6.0 4.0 3.5 #57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0 (Black) (Silver) (Silver) (Black) 7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11 1.7 2.0 2.0 2.6 4.0 6.0 5.0 5.0,

HARDWARE LIST (4/5)

#61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 #64: M1.7 X 5.0 (Tapping) (Black) (Silver) (Black) (Silver) 7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21 3.0 2.0 5.0 1.7 10.0 12.53.0 5.0 #65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0 (Silver) (Silver) (Silver) (Silver) 2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01 1.4 1.4 1.4 1.7 3.5 1.4 2.0 4.0 #69: M1.7 X 3.0 #70: M1.7 X 5.0 #71: M1.4 X 2.0 #72: M1.4 X 2.0 (Silver) (Silver) (Red) (Silver) 2-599-475-21 2-599-475-41 3-208-537-01 4-663-621-41 1.7 1.7 1.4 1.4 3.0 5.0 2.0 2.0 #73: M1.2 X 4.0 (Tapping) #74: M1.7 X 6.0 (Tapping) #75: M1.7 X 3.5 (Tapping) #76: M1.7 X 4.0 (Tapping) (Black) (Silver) (Silver) (Silver) 3-086-156-61 2-666-551-31 2-666-551-01 2-666-551-11 1.2 1.7 1.7 1.7 4.0 6.0 3.5 4.0 #77: M1.2 X 5.0 (Tapping) #78: M1.4 X 3.5 #79: M1.4X 2.0 #80: M1.4X 2.0 (Silver) (Red) (Silver) (Black) 3-086-156-31 3-208-537-11 2-587-151-11 3-279-411-01 1.2 1.4 1.4 1.4 5.0 3.5 2.0 2.0,

HARDWARE LIST (5/5)

#81: M1.7 X 2.5 #82: M1.4 X 1.4 (Silver) (Silver) 2-515-756-01 3-272-251-01 1.7 1.4 2.5 1.4,

Reverse 985221631.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2007.08 Official Release — —]
15

Similar documents

SPECIFICATIONS Camera [Exposure] Operating temperature
DSLR-A100 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2006.07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Revised-1 Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SE
6-1-2. FRONT CABINET ASSEMBLY
DSC-F505V SECTION 6 REPAIR PARTS LIST 6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • Items marked “*” are not stocked since they are Replace only with part number speci- have some d
Note: Follow the disassembly procedure in the numerical order given.
DSC-F505V SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. DSC-F505V 2-1. REAR CABINET BLOCK 2-2. ZOOM LENS BLOCK (Page 2-2) (Page 2-2) 2-5. LCD PANEL BLOCK 2-6. HI-73, DD-148 BOARDS, 2-3. CABINET (LT) BLOCK CONTROL SWITCH BLOCK (FK) BATTERY HOLDER BLOCK (Page 2-3) (Pag
Model information table
DSC-T70/T75 SERVICE MANUAL LEVEL 3 US Model Ver. 1.0 2007.08 Canadian Model Revision History AEP Model UK Model Internal memory E Model ON BOARD Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Photo: Silver Japanese Model Tourist Model Link SERVICE NOTE SCH
Supplied accessories
DSC-F505 SERVICE MANUAL US Model Canadian Model Level 2 Ver 1.2 2000. 03 With SUPPLEMENT-1 AEP Model (9-974-192-81) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model This service manual contains information for Japanese model as well. On the PS-427, SY-56 boar
DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06
DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06 On the SY-59 board This service manual contains information This service manual provides the information that is premised the circuit board for japanese model as well.
Page Changed contents
DSC-F55/F55E US Model Canadian Model SERVICE MANUAL Tourist ModelKorea Model DSC-F55 1999. 07 E Model DSC-F55/F55E AEP Model UK Model Australian Model Hong Kong Model Chinese Model DSC-F55E SUPPLEMENT-1 File this supplement-1 with the Service Manual. (99-009) Subject: • Addition of Korea model • Suf
AUTION ou are cautioned that any changes or
DSC-F717 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
Trademarks About the Carl Zeiss lens
DSC-F77/FX77 SERVICE MANUAL LEVEL 1 AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MAN
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL i
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
DSC-H2 SERVICE MANUAL LEVEL 2 US Model UK Model Chinese Model Korea Model Tourist Model
DSC-H2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006. 02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Argentina Model ON BOARD Hong Kong Model Korea Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WI
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1 Ver 1.2 2005. 09 US Model Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model How to use Australian Model Acrobat Reader Chinese Model Japanese Model Korea Model Tourist Model Internal memory ON BOARD Link SPECIFICATIONS BLOCK DIAGRAMS PRIN
SPECIFICATIONS Camera
DSC-H7/H9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2007.04 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: DSC-H7 Black Model Brazilian Model Tourist Model J
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTR
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.1 2005. 04 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.2 2005. 09 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-N2 SERVICE MANUAL SUPPLEMENT-1
DSC-N2 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.02 SUPPLEMENT-1 File this supplement with the service manual. (PV06-161) • Addition of Brazilian Model • Change of Automatic Adjustment Program • Addition of Brazilian Model & : Points added portion. INITIAL LANGUAGE Default Data Check (Service manual pag
DSC-N2 SERVICE MANUAL Canadian Model
DSC-N2 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.1 2007.02 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. (DI06-165) • Addition of
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model UK Model Hong Kong Model Argentine Model Japanese Model Tourist Model Link
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-N2 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Argentine Model Brazilian Model Japanese Model
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory ON BOARD Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Link SPECIFICAT
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.0 2004.04 US Model Canadian Model Revision History E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P100/P120 AEP Model UK Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O