Download: Supplied accessories

DSC-F505 SERVICE MANUAL US Model Canadian Model Level 2 Ver 1.2 2000. 03 With SUPPLEMENT-1 AEP Model (9-974-192-81) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model This service manual contains information for Japanese model as well. On the PS-427, SY-56 board PS-427 board This service manual provides the information that is premised the circuit Schematic diagram ...Pages 4-15 to 4-18 board replacement service and not intended repair inside the PS-427, Printed wiring board ...Page 4-11 SY-56 board. Electrical parts list ...Pages 6-12 to 6-13 Therefore, ...
Author: Acal1978 Shared: 8/19/19
Downloads: 387 Views: 1013

Content

DSC-F505 SERVICE MANUAL US Model Canadian Model Level 2 Ver 1.2 2000. 03 With SUPPLEMENT-1 AEP Model

(9-974-192-81) UK Model

E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model

This service manual contains information for Japanese model as well. On the PS-427, SY-56 board PS-427 board This service manual provides the information that is premised the circuit Schematic diagram ...Pages 4-15 to 4-18 board replacement service and not intended repair inside the PS-427, Printed wiring board ...Page 4-11 SY-56 board. Electrical parts list ...Pages 6-12 to 6-13 Therefore, schematic diagram, printed wiring board and electrical parts SY-56 board list of the PS-427, SY-56 board are not shown. Schematic diagram ...Pages 4-23 to 4-33 The following pages are not shown. Printed wiring board ...Pages 4-19 to 4-22 Electrical parts list ...Pages 6-13 to 6-14

SPECIFICATIONS

System Memory General Output voltage Recording format “Memory stick” Power consumption DC OUT : 4.2 V, 1.8 A in operating Digital (JPEG based)/Field Flash Using the AC power mode recording Recording distance adaptor/charger : Battery charge terminal : Video signal limitations : 11 7/8 inches to 8 1/3 feet Recording : 3.6 W 4.2 V, 1.5 A in charge mode NTSC color, EIA standards (0.3 m to 2.5 m), automatic flash Playback : 3.1 W Operation temperature PAL color CCIR standards control system Using the rechargeable 32°F to 104°F (0°C to 40°C) Image device Shutter speed NP-FS11 lithium ion battery : Storage temperature 1/2-inch CCD (total number NTSC : 1/8 - 1/725 Recording : 3.3 W -4°F to 140°F (-20°C to 60°C) of square pixels : 1636 x 1236), PAL : 1/6 - 1/600 Playback : 2.7 W Approx. 1 15/16x19/16x33/8 in. square grid, primary color filter Operation temperature (49 x 39 x 85 mm) (w / h / d) Interface format LCD screen 32°F to 104°F (0°C to 40°C) Mass Lens Screen size Storage temperature Approx. 4.2 oz. (120 g) ƒ = 7.1 - 35.5 mm (38 - 190 mm, when 2 inches -4°F to 140°F (-20°C to 60°C) (excluding batteries) converted into a 35 mm still camera) LCD panel Dimensions 0.5 m - ∞ (“W” side) TFT Approx. 4 1/4x21/2x53/8 in. NP-FS11 battery pack 0.08 m - ∞ (Macro, “W” side) Total dot number (107.2 x 62.2 135.9 mm) Voltage F = 2.8 - 3.3 122,980 (559 x 220) dots (w / h / d) DC 3.6 V Photometric system Mass Capacity TTL system Input and output connectors Approx. 15 oz (435 g) 4.1 Wh Exposure control A/V out (Monaural) (excluding batteries) Type Automatic exposure Minijack Approx. 1 lb (475 g) Lithium ion type White balance Video : 1Vp-p, 75 ohms, (including battery, Automatic, Indoor, Outdoor, unbalanced, sync negative “Memory stick” (4 MB), Design and specifications are subject One-push Audio : monaural, 327 mV wrist strap and lens cap etc.) to change without notice. Data compression system (at output, impedance more than Movie : MPEG-1 47 kilohms) AC-VF10 AC power adaptor/ Still : JPEG Output impedance with less than charger Audio (with still image) : 2.2 kilohms Power requirements MPEG AUDIO (Monaural) Digital I/O (serial) 100 to 240 V AC, 50/60 Hz Data format Minijack Power consumption Still : 1600 x 1200 RS-232C based, 9.6 Kbps to 13 W 1024 x 768 115.2 Kbps 640 x 480 Digital I/O (USB) DIGITAL STILL CAMERA 320 x 240 (E-mail) Special minijack Movie : 320 x 240, 160 x 112 USB 1.0 based

MICROFILM

– 1 –, Supplied accessories 1 AC-VF10 AC power adaptor/charger, 123Power cord (1) 2 A/V connecting cable (1) 3 NP-FS11 Battery pack (1) 4 DK-115 DC connecting cable (1) 45675Wrist strap (1) 6 Memory Stick (4MB) (1) 7 Lens cap/Lens cap strap (1) 8 9 !º !¡ 8 Sony Picture Gear 3.2Lite (1) (Compact Disk) 9 PC serial cable (1) !º Conversion plug 3P adaptor (1) UK, Hong Kong model !™ !£ !¢ !¡ 2-pin conversion adaptor (1) E model !™ 2-pin conversion adaptor (1) Tourist model !£ USB driver software (1) !¢ USB cable (1) SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered 4. Look for parts which, through functioning, show obvious signs connections. Check the entire board surface for solder splashes of deterioration. Point them out to the customer and and bridges. recommend their replacement. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. "pinched" or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, particularly • Keep the temperature of the soldering iron around 270˚C transistors, that were installed during a previous repair. Point during repairing. them out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. – 2 –, TABLE OF CONTENTS 1. GENERAL ... 1-1 4. PRINTED WIRING BOARDS AND Parts identification ... 1-1 SCHEMATIC DIAGRAMS Preparation ... 1-2 4-1. Frame Schematic Diagram (1) ... 4-3 1 Charging the battery pack and Frame Schematic Diagram (2) ... 4-5 “Memory Stick” ... 1-2 4-2. Printed Wiring Boards and Schematic Diagram... 4-7 2 Installing the battery pack ... 1-3 • CD-236 (CCD Imager, Camera) 3 Setting the date and time ... 1-3 Printed Wiring Board ... 4-7 Recording ... 1-4 • CD-236 (CCD Imager, Camera) Recording still images ... 1-4 Schematic Diagram...4-9 Recording moving images ... 1-4 • LD-98 (Lens Drive) Playing back ... 1-5 Printed Wiring Board ... 4-12 Playing back still images ... 1-5 • MF UNIT Playing back moving images ... 1-5 Schematic Diagram... 4-33 Viewing images using a personal computer ... 1-5 • CF/PW (Control Switch Block) Various ways of recording ... 1-8 Schematic Diagram... 4-33 Various ways of playback ... 1-10 • HI-70 (LCD Drive, Timing Generator, Video, Changing the menu setting ... 1-13 Audio, Hi Control) Using image data with other equipment ... 1-14 Printed Wiring Board ... 4-35 Additional information ... 1-15 • HI-70 (LCD Drive) Schematic Diagram... 4-39 2. DISASSEMBLY • HI-70 (Timing Generator) • Attachiment of CPC-9 Jig ... 2-1 Schematic Diagram... 4-41 2-1. Removal of Rear Cabinet Block ... 2-2 • HI-70 (Video) 2-2. Removal of Zoom Lens Block ... 2-2 Schematic Diagram... 4-43 2-3 Removal of Cabinet (LT) Block ... 2-3 • HI-70 (Audio) 2-4. Removal of Lens Block ... 2-3 Schematic Diagram... 4-45 • Service Positionn-1 (Lens Block Area : CD-236, LD-98, • HI-70 (Hi Control (1/2) ) PS-427 and SY-56 Boards) ... 2-3 Schematic Diagram... 4-47 2-5. Removal of LCD Panel Block and • HI-70 (Hi Control (2/2) ) Control Switch Block (FK) ... 2-4 Schematic Diagram... 4-49 • Service Positionn-2 (Rear Cabinet Area : LCD Panel and • DD-131 (DC/DC Converter) Control Switch Block (FK)) ... 2-4 Printed Wiring Board ... 4-51 2-6. Removal of HI-70, DD-131 Boards and • DD-131 (DC/DC Converter) Battery Holder Block ... 2-5 Schematic Diagram... 4-53 2-7. Removal of Upper Cabinet Block and Flash Unit (MC) ...2-5 • FK (Control Switch Block) • Service Positionn-3 (HI-70 and DD-131 Boards) ... 2-6 Schematic Diagram... 4-55 2-8. Removal of Front Cabinet Assembly ... 2-6 4-3. Waveforms ... 4-57 2-9. Removal and Attaciment of FP-133 Flexible Board ... 2-7 4-4. Printed Parts Location ... 4-59 2-10. To Fold the New FP-133 Flexible Board ... 2-7 2-11. Removal of Crystal Indication Module ... 2-8 2-12. Removal of Flash Unit (ST) ... 2-8 2-13. Circuit Boards Location ... 2-9 2-14. Flexible Boards and Control Switch Block Location ... 2-9 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram ... 3-1 – 3 –, 5. ADJUSTMENTS 1-5. LCD SYSTEM ADJUSTMENT ... 5-35 1. Before starting adjustment ... 5-1 1. LCD Initial Data Input ... 5-35 1-1. Adjusting items when replacing main parts and boards .. 5-2 2. VCO Adjustment (Control Switch Block (FK) ) ... 5-36 5-1. Adjustments ... 5-3 3. D Range Adjustment (Control Switch Block (FK) ) ...5-36 1-1. Preparations Before Adjustment ... 5-3 4. Bright Adjustment (Control Switch Block (FK) ) ...5-37 1-1-1.List of Service Tools ... 5-3 5. Contrast Adjustment (Control Switch Block (FK) ) ... 5-37 1-1-2.Preparations ... 5-4 6. Color Adjustment (Control Switch Block (FK) ) ... 5-38 1-1-3.Discharging of the strobe power supply ... 5-4 7. V-COM Level Adjustment (Control Switch Block 1-1-4.Precaution ... 5-6 (FK) ) ...5-38 1. Setting the Switch ... 5-6 8. V-COM Adjustment ... 5-39 2. Order of Adjustments ... 5-6 9. White Balance Adjustment (HI-70 board) ...5-39 3. Subjects ... 5-6 1-6. System Control System Adjustment ... 5-40 4. Preparing the Flash Adjustment Box ... 5-7 1. Battery End Adjustment (SY-54 board) ...5-40 1-2. Initialization of B, D, E, F, 7 Page Data ... 5-8 5-2. Service Mode ...5-41 1-2-1. Initialization of D Page Data ... 5-8 2-1. Adjustment Remote Commander ... 5-41 1. Initializing the D Page Data ... 5-8 1. Using the adjustment remote commander ...5-41 2. Modification of D Page Data ... 5-8 2. Precautions upon using the adjustment remote 3. D Page Table ... 5-8 commander ... 5-41 1-2-2. Initializing the B, E, F, 7 Page Data ... 5-11 2-2. Data Process ... 5-42 1. Initializing the B, E, F, 7 Page Data ... 5-11 2-3. Service Mode ...5-43 2. Modification of B, E, F, 7 Page Data ... 5-11 1. Setting the Test Mode ... 5-43 3. F Page table ... 5-11 2. Bit value discrimination ... 5-43 4. E Page Table ... 5-14 3. Switch check (1) ... 5-44 5. B Page Table ... 5-16 4. Switch check (2) ... 5-44 6. 7 Page Table ... 5-19 5. LED check ...5-44 1-3. Video System Adjustments ... 5-21 5-3. System Control Adjustment ... 5-45 1. Video Sync Level Adjustment ... 5-21 1. Initializing the data of pages B, C, D, E, F, 7 ... 5-45 (Control Switch Block (FK) ) ... 5-21 2. Inputting the serial No. ... 5-45 2. Video Burst Level Adjustment ... 5-21 2-1. Inputting the serial No. ... 5-45 (Control Switch Block (FK) ) ... 5-21 3. Video Y Level Check ... 5-21 6. REPAIR PARTS LIST (Control Switch Block (FK) ) ... 5-21 6-1. Exploded Views ... 6-1 1-4. Camera System Adjustments ... 5-22 6-1-1.Battery Holder Assembly ... 6-1 1. HALL Adjustment ... 5-22 6-1-2.Front Cabinet Assembly ... 6-2 2. Flange Back Adjustment (Using Minipattern Box) ... 5-23 6-1-3.Rear Cabinet Assembly ... 6-3 3. Flange Back Adjustment ... 5-24 6-1-4.Lens Cabinet Assembly ... 6-4 (Using Flange Back Adjustment Chart) ... 5-24 6-1-5.Lens Assembly ... 6-5 4. Flange Back Check ... 5-24 6-2. Electrical Parts List ... 6-6 5. Picture Frame Setting ... 5-25 6. F No. Standard Data Input ... 5-25 7. Mechanical Shutter Adjustment ... 5-26 8. AGC Standard Gain and Max Gain Adjustment ... 5-26 9. Light Level Adjustment and ND SHUTTER CHECK .. 5-26 10. Auto White Balance Standard Data Input ... 5-27 11. Auto White Balance ND Filter Compensation Adjustment ... 5-27 12. Auto White Balance Adjustment ... 5-28 13. Color Reproduction Adjustment ... 5-29 13-1. Color Reproduction Adjustment (Without ND Filter) ... 5-29 13-2. Color Reproduction Adjustment (With ND Filter) ... 5-29 13-3. Color Reproduction Check ... 5-30 14. White Balance Check ... 5-31 15. Strobe White Balance Adjustment ... 5-31 16. Strobe Light Level and White Balance Check ... 5-32 17. CCD Black Defect Compensation ... 5-32 18. CCD Black Defect Compensation Check ... 5-33 19. CCD White Defect Compensation ... 5-34 20. CCD White Defect Compensation Check ... 5-34 * The color reproduction frame is shown on page 141. – 4 –,

SERVICE NOTE

[Discharging of the FLASH unit’s charging capacitor] The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-F505 is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig. a small clip is attached to each end of a resistor of 1kΩ /1W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. 1kΩ/1W Wrap insulating tape. Discharging the Capacitor Short circuits between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds. Capacitor Short jig Flash unit (MC) – 5 –, [Description on Self-diagnosis Display] Self-diagnosis display • C: ππ: ππ You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ππ: ππ Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:04:ππ Use a NP-FS11/F10 battery pack. You are using a basttery pack that is not an for “InfoLITHIUM” BATTERY “InfoLITHIUM” battery pack. ONLY C:32:ππ Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ππ Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ππ Checking of lens drive circuit. When failed in the focus and zoom *1 initialization. — ππ Checking of flash unit or replacement Abnormality when flash is being E:91: of flash unit. charged. *2 Note : The error code is cleared if the battery is removed, except defective flash, unit. *1 : The error display is given in two ways. *2 : When the flash charging failed, Page:D, Address:C7, Data:04 are written. After repair, be sure to write Page:D, Address:C7, Data:00. – 6 –,

DSC-F505 SECTION 1

This section is extracted from

GENERAL instruction manual.

1-1,

DSF-F505 SECTION 2 DISASSEMBLY The equipment can be removed using the following procedure. START

2-1. REAR CABINET BLOCK 2-2. ZOOM LENS BLOCK 2-5. LCD PANEL BLOCK 2-3. CABINET (LT) BLOCK 2-6. HI-70 AND DD-131 BOARDSCONTROL SWITCH BLOCK (FK) BATTERY HOLDER BLOCK 2-7. UPPER CABINET BLOCK 2-4. LENS BLOCK ATTACHMENT OF CPC-9 JIG CONTROL SW BLOCK (PW) AND FLASH UNIT (MC) SERVICE POSITION-2 · LCD PANEL BLOCK · CONTROL SWITCH BLOCK (FK) ATTACHMENT OF CPC-9 JIG AND ATTACHMENT OF CPC-9 JIG 2-8. FRONT CABINET ASSEMBLY SERVICE POSITION-1 AND · CD-236 BOARD SERVICE POSITION-3 · LD-98 BOARD 2-11. CRYSTAL INDICATION MODULE · HI-70 BOARD · PS-427 BOARD AND OTHER · DD-131 BOARD · SY-56 BOARD ABOUT FP-133 FLEXIBLE BOARD. (Refer to 2-9. and 2-10.) 2-12. FLASH UNIT (ST) • ATTACHMENT OF CPC-9 JIG Slide the Release knob in the direction of arrow A. Control switch block (FK) To open the Battery lid. (CN002) 18

A

CPC-9 jig (J-6082-393-C) (18p flexible board) Two claws CPC cover Release knob Note : Don't use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit 2-1, NOTE : Follow the disassembly procedure in the numerical order given. 2-1. REMOVAL OF REAR CABINET BLOCK 2 Two screws 4 FP-134 flexible board (M1.7) (HI-70 board, CN901) 5 Flexible board (Control switch block (FK)) (HI-70 board, CN607) 1 Two screws (M1.7) Front cabinet assembly 3 Rear cabinet assembly 6 Harness (HB-50) (HI-70 board, CN605) 7 Harness (SP-163) (HI-70 board, CN702) 2-2. REMOVAL OF ZOOM LENS BLOCK 1 Screw (M1.7) 4 CN456 (SY-56 board) 3 Screw (M1.7) 5 CN455 (SY-56 board) FP-133 flexible board 6 Zoom lens block 2 Screw (M1.7) 7 MF ornament 2-2, 2-3 REMOVAL OF CABINET (LT) BLOCK 2-4. REMOVAL OF LENS BLOCK 2 Screw (M1.7) 3 Cabinet (LT) block 5 Harness (SM-114) (Flash unit (ST), 2P) (Note) 8 Screw (M1.7) Flash unit (Note) 7 Two screws 2 CN453 (M1.7) (SY-56 board) 1 Push the Release knob 4 FP-136 flexible board (SY-56 board, CN454) 0 Lens block 3 CN001 (Control switch block) 1 Screw (M1.7) 6 Cabinet (MF) 4 Control switch Harness clamp assembly block (CF) Cabinet (LT) block (Bottom view) 9 Cabinet (LB) assembly NOTE : Clamp the cables after attaching the Harness (MS-114). If clamped with the flash unit closed, the flash unit cannot 5 Two screws be opened, Be sure to clamp the cable with the flash unit (M1.7) opened. • SERVICE POSITION-1 (LENS BLOCK AREA : CD-236, LD-98, PS-427 and SY-56 BOARDS) Rear cabinet block CN602 (HI-70 board) CN603 (HI-70 board) Extension cable (33, 39P 0.3 mm) Parts No. : J-6082-447-A (HI-70 board, CN602, 603) (SY-56 board, CN455, 456) FP-133 flexible board (Not used) Control switch block (CF) Harness (MS-114) SY-56 board Cabinet (LT) block (to Cabinet (LT) block) (Flash unit (ST)) Cabinet (MF) assembly Harness (MS-114) (from Front cabinet block) PS-427 board LD-98 board Extension cable (39P 0.3 mm) Parts No. : J-6082-448-A (PS-427 board, CN251) CD-236 board (CD-236 board, CN101) Lens block 2-3, 2-5. REMOVAL OF LCD PANEL BLOCK AND CONTROL SWITCH BLOCK (FK) Rear cabinet assembly 8 Control switch block (FK) 2 Zoom switch Button (LCD bright) (RV001) 1 Screw (1.7 x 4) 6 Screw (M1.7) Knob (LCD back light) 3 Two screws (1.7 x 4) 7 Two screws (M1.7) 4 Two screws (1.7) 5 LCD panel block (Refer to 2-11. for details diagram on removal of LCD section) • SERVICE POSITION-2 (REAR CABINET AREA : LCD PANEL and CONTROL SWITCH BLOCK (FK)) Cold cathode fluorescent tube (ND901) (with Inverter transformer unit) Control switch block (FK) CN901 (HI-70 board) Crystal indication module (LCD901) (with FP-134 flexible board) SP901 CN607 (HI-70 board) Harness (From the SP901) (HI-70 board, CN702) 2-4, 2-6. REMOVAL OF HI-70, DD-131 BOARDS AND BATTERY HOLDER BLOCK 8 Screw (M1.7) 5 Three screws (1.7 x 4) 0 Battery holder block 3 Harness (Microphone) 6 HI-70 board (HI-70 board, CN701) 4 Control switch block (PW) (HI-70 board, CN604) BB fixed sheet 9 Screw (M1.7) 1 FP-132 flexible board (HI-70 board, CN601) (DD-131 board, CN003) 2 FP-133 flexible board (HI-70 board, CN602,603) !™ DD-131 board 7 Harness (MD-97) !¡ Two screws (DD-131 board, CN002) (1.7 x 4) 2-7. REMOVAL OF UPPER CABINET BLOCK AND FLASH UNIT (MC) NOTE : When the flash unit (MC) charging failed, Page : D, Address : C7, Data : 04 are written. After repair, be sure to write Page : D, Address : C7, Data : 00. Details diagram on removal and attachment of Control switch block (PW) 3 Upper cabinet block Upper cabinet block (Take note of two claws A) 1 Screw (M1.7) Pin 2 Harness (GN-52) Claw Hole Claw Claw Two clawsA5Flash unit (MC) (Note) (Take note of claw B) Claw Groove Edge Screw (1.7 x 4) Control switch block (PW) JK retainer assembly Claw B Screw (1.7 x 4)Edge Groove Note for installation of 4 Harness (MS-114) Flash unit (MC) Groove Should be fit to the Front Flash unit (MC) cabinet groove. Groove 2-5, • SERVICE POSITION-3 (HI-70 and DD-131 BOARDS) HI-70 board Control switch block (PW) CN602 Rear cabinet block CN603 Front cabinet block DD-131 board CN702 Harness (HB-50) Harness (SP-163) FP-133 flexible board CN605 (Not used) CN456 (SY-56 board) CN455 (SY-56 board) Battery holder block (To AC power adaptor) Zoom lens block Extension cable (33, 39P 0.3 mm) Parts No. : J-6082-447-A (HI-70 board, CN602, 603) (SY-56 board, CN455, 456) 2-8. REMOVAL OF FRONT CABINET ASSEMBLY 1 Lift up the Zoom lens block. 4 Front cabinet assembly 3 Screw (M2 x 4) 2 Screw (M2 x 4) 2-6, 2-9. REMOVAL AND ATTACHIMENT OF FP-133 FLEXIBLE BOARD

NOTE : For folding new FP-133 flexible board, refer to “2-10. To

fold the new FP-133 flexible board” . FP-133 flexible board When attaching, coil in the direction of (33P side) arrow A with two and a half revolutions. FP-133 flexible board (FP-133 flexible board ) (39P side) Screw (M1.7) Harness (GN-52)

A

Hook cover Hinge cover Harness (MS-114) Screw (M1.7) CN456 (SY-56 board) FP holder Screw (M2 x 4) CN455 (SY-56 board) Hook the claw of harness Harness (GN-52) Harness (GN-52) FP-133 flexible board (39P side) FP-133 flexible board (33P side) Harness (MS-114) FP guard 2-10. TO FOLD THE NEW FP-133 FLEXIBLE BOARD : Fold NOTE : For attaching new FP-133 flexible board, refer to “2-9.

Removal and attachment of FP-133 flexible board” .

Adhesive tape : Fold Adhesive tape 1-675-590-xx FP-133 Adhesive tape 1-675-590-xx FP-133 Adhesive tape 2-7, 2-11. REMOVAL OF CRYSTAL INDICATION MODULE Note for installation 1 Crystal indication module (LCD901) (FP-134 flexible board, 24P) Portion B BL cushion Portion A Portion C andD5Cold cathode fluorescent tube (ND901) (Inverter transformer unit) 3 FP-134 flexible board 4 Screw (M1.7)

D C

BL light interception sheet

B A

6 Inverter transformer unit 2 Screw (M1.7) BL insulating sheet 2-12. REMOVAL OF FLASH UNIT (ST) 4 Cabinet (ST) (Take note of four claws) 5 Flash unit (ST) 1 Screw (M1.7 x 4) Claw Claw Claw 2 FP-136 flexible board Claw (Flash unit ST) 3 Push the Release knob 2-8, 2-13. CIRCUIT BOARDS LOCATION CD-236 HI-70 (CCD imager, Camera) (LCD drive, Timing generator, Video, Audio, HI control) LD-98 (Lens drive) Flash unit (MC) Flash unit (ST) PS-427 (Camera DSP, Memory control) SY-56 (SH DSP, Memory, Serial I / O, Connector, Digital I / O, ) Inverter transformer unit DD-131 (DC / DC Converter) 2-14. FLEXIBLE BOARDS AND CONTROL SWITCH BLOCK LOCATION FP-134 Control switch block (PW) Control switch block (FK) FP-132 FP-136 FP-133 FP-135 Lens block Control switch block (CF) Manual focus block 2-9E, ST UNREG HALL AD REC OUT A OUT L MC XCS4 MC XCSO M CXCS

Ver 1.1 1999.10 DSC-F505 SECTION 3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM

CD-236 BOARD PS-427 BOARD SY-56 BOARD

LENS IRIS

METER IC101 CCD OUT IC103 IC251 16 DATA BUS

DATA BUS IO CCD IMAGER A/D CONV. CAMERA DSP (SEE PAGE 4-9) (SEE PAGE 4-9) MEMORY CONTROL 16 VIDEO ENCODER OPD, OSD, HOST IF 16 ADDRESS BUS M902 M901 V1A, V1B, V2A RES CONTROL FOCUS ZOOM HALL V3A, V3B, V4 SG, JPEG, L-MODE MC XCS1 23 16 12 16 12 16 20 16 3 16 MOTOR MOTOR H RG, VSHT IC102 (SEE PAGE 4-16) 9Y

M M USB D+TIMING R-Y/CMCK12 IC201 IC453 IC307 IC451H1, H2 IC456 IC301 USB D–GENERATOR B-Y/CMCK14 USB IF SDRAM FLASH MEMORY(SEE PAGE 4-9)

SERIAL I/O MC CAM (SEE PAGE 4-33) 16Mbit ROM STICK MC DIOFOCUS ZOOM MC XCS3 HOST IF SH DSP (SEE PAGE 4-28) 8Mbit IF MC SCKRESET MOTOR AUDIO OF (SEE PAGE 4-23) MC XCS USB (SEE PAGE 4-25) (SEE PAGE 4-28)SENSOR SENSOR SHUTTER CONTROL

LD-98 BOARD DATA FLASH CONTROL IC302IC252 (SEE PAGE 4-29)16 IC303

AU SDTO

IC403 SDRAM IC304ADDRESS AU SDTI MC XCS MS

DRIVE (+) 64Mbit LOGIC SHUTTER (SEE PAGE 4-18) 14 (SEE PAGE 4-24)

IC402 DRIVE

MCX CS MCX CSO (SEE PAGE 4-13) M SHUT ON M SHUT ON MCX CS4 (SEE PAGE 4-13) ZOOM MOTOR SENS ZOOM MOTOR SENS USB D+/USB – FOCUS ZOOM TXD232C/RXD232C T1 OUTFOCUS MOTOR SENS FOCUS MOTOR SENS MOTOR MOTOR IC455 IC306 R1 INDRIVE DRIVE

IC404 IRIS CONT 1, 2DRIVE (–) IC407 AUDIO AD/DA CONV. IC308

RS232C DRIVE (SEE PAGE 4-25)

IC405 STRB ON

(SEE PAGE 4-29) EVR EEP ROM

IC406 (D/A CONV.) (SEE PAGE 4-25)(SEE PAGE 4-13)

(SEE PAGE 4-13) IRIS (SEE PAGE 4-14)FOCUS, ZOOM MOTOR DRIVEHALL (+) PREDRIVE HALL AMP HALL AD CNT Y HI SO, HI SI, XHI SCK CNT C CNT Y/C CAM SO, CAM SI, XCAM SCK CAM SO, CAM SI, XCAM SCK

IC607

EEP ROM CN606 (SEE PAGE 4-50)

FLASH UNIT (ST) (MC) MEMORYSTICK

STRB ON FLASH UNIT HI-70 ND901

BOARD IC801 CONTROL

BL UNREG BACK BL ON SWITCH J001 EVR LIGHT

DD-131 BOARD DIGITALMIC901 BLOCK(SEE PAGE 4-39) UNIT (PW) I/O

SYS DD ON MIC LCD901CAM DD ON R1 OUT (RS232C) Y R LCD DD ON R-Y IC802 LCDG PANEL B-Y LCD DRIVE B T1 OUT

IC001 (SEE PAGE 4-40) CN002USB D+

DC/DC CAM +15VD DIGITALUSB D– CONVERTER CAM –7.5V I/O (SEE PAGE 4-53) A +4.9V IC901 XPWR SW POWER (USB) M +5V TIMING

IC702 SWITCHD +2.35V GENERATOR

(SEE PAGE 4-41) XSHTR LOOK SWD +3.2V LINE/SPEAKER SHUTTERXSHTR SW A +3.2VCYAMP AUDIO AUDIO SWITCH PANEL +13.5V (SEE PAGE 4-45) MOVIE/STILL SW PANEL +6.5V CNT Y IC301 HI SI, HI SO, HI XSCK MOVIE/STILLVIDEO XCAM/PW SW PLAY SWITCH PANEL +4.9V CNT C VIDEO AMP PANEL –15V (SEE PAGE 4-44) XPWR SW EVER +3.5V IC601 IC603 CONTROLXSHTR LOOK SW SWITCH RESET HI XSHTR SW (FK) (SEE PAGE 4-49) CONTROL MOVIE/STILL SW

IC605 (SEE PAGE 4-49) KEY AD1XCAM/PW SWBACK UP VCC FUNCTIONKEY AD2

KEY AD1 KEY REG BL ON (SEE PAGE 4-49) KEY AD2

IC606 KEY AD4

ZOOM SW AD ZOOM

SWITCH

BT901 HI UNREG ZOOM SW ADRESET VIDEO J001 BATTERY FOCUS A(SEE PAGE 4-49) AUDIO VIDEO TERMINAL FOCUS B FOCUS A AUDIO HALL AD BL ON FOCUS B A/V OUT BATT SIG

S KEY AD4SYS DD ON

CAM DD ON BATT SIG BATT SIG LCD DD ON CONTROL

IC602 SWITCH09 BL UNREG BLOCK FUNCTION

TIMER + BT601 (CF) SWITCH CLOCK – LITHIUM SP901 (SEE PAGE 4-50) BATTERY SPEAKER SP+, SP– MF

UNIT MANUAL FOCUS

3-1 3-2E, Yellow Cyan Green Yellow White Cyan Magenta Green Red White Blue Magenta Red Blue

Ver 1.1 1999.10 DSC-F505 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) • b: Pattern from the side which enables seeing. • Voltages and waveforms are measured between the measure- (The other layers' patterns are not indicated.) ment points and ground when camera shoots color bar chart of • Through hole is omitted. pattern box. They are reference values and reference wave- • Circled numbers refer to waveforms. forms. • There are few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used.). isn’t mounted in this model. • Voltage values change depending upon input impedance of VOM • Chip parts. used.) Transistor DiodeC6544564512333431. Connection Pattern boxBE12332132154321212112(For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. 50V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10W unless otherwise noted. About 90 cm kΩ=1000Ω, MΩ=1000kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Be- cause it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH Front of the lens TA A 2520 2. Adjust the distance so that the output waveform of Fig. a and Kinds of capacitor the Fig. b can be obtain. Temperature characteristics H External dimensions (mm) • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. A B A=BBA• Signal name XEDIT → EDIT PB/XREC → PB/REC Fig. a (Video output terminal output waveform) • 2 : non flammable resistor • 1 : fusible resistor • C : panel designation Electron beam • A : B+ Line * scanned frame • B : B– Line * • J : IN/OUT direction of (+,–) B LINE. * CRT picture frame • C : adjustment for repair. * • Circled numbers refer to waveforms. * * Indicated by the color red. Fig.b (Picture on monitor TV) Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une When indicating parts by reference number, pleas include specified. pièce portant le numéro spécifié. the board name. 4-1,

FP-135 FLEXIBLE FP-133 FLEXIBLE MS-114 HARNESS TO FRAME SCHEMATIC DIAGRAM(2/2) DSC-F505 Ver 1.1 1999.10

4-1. FRAME SCHEMATIC DIAGRAM (1) 12345678910 11 12 13 14 15 16 17 18

A CONTROL SWITCH BLOCK(CF) CN002 10P CN453 10P 2P

S001 -MOUNT FLEXIBLE- 1 KEY_AD4 REG_GND12D_3.2V DC_300V 2

MACRO MF UNIT S005 3 REG_GND

S002 S004 (CARD EDGE) (W/B SET) FOCUS 4 PHOTOTR_5V 6 D_3.2V FLASH UNITAUTO SPOT S003 5 PHOTOTR_OUT 5 FOUCUS_A METER WHT BAL 6 REG_GNDB 4 FOUCUS_B MANUAL (ST)7 REG_GND 3 REGGND 8 FOCUS_B XSTB_OPEN11XSTB_OPEN Q004 2 PHOTOTR_OUT 9 FOCUS_A PANEL_B-Y 80 80 PANEL_B-Y GND 2 FP-136 2 GNDBRIGHT 1 PHOTOTR_5V LEVEL 10 D3.2V SENSOR CN004 CN001 6P Y_OUT 79 79 Y_OUT GND33GND

FLEXIBLE

6P PANEL_R-Y 78 78 PANEL_R-Y STB_ON44STB_ON C_OUT 77 77 C_OUT A_4.9V55A_4.9V CN401 27P PANEL_Y 76 76 PANEL_Y A_4.9V66A_4.9V 1 ZOOM_A A_3.2V 30 30 A_3.2V HDO 75 75 HDO 6P CN454 6P

C 2 ZOOM_B A_3.2V 29 29 A_3.2V CA_FD 74 74 CA_FD 39P CN456

3 ZOOM_A PE_DAC_LEVEL 28 28 PE_DAC_LEVEL ANS_XIRL4 73 73 ANS_XIRL4 REG_GND 1

LENS 4 ZOOM_B AGC_CONT2 27 27 AGC_CONT2 ANS_XIRL3 72 72 ANS_XIRL3 REG_GND 2CCD

5 Z_SENS_VCC LENS_RST_LED 26 26 LENS_RST_LED ANS_XIRL2 71 71 ANS_XIRL2 CAM_15V 3

IMAGER UNIT 6 Z_SENS_RST AGC_CONT1 25 25 AGC_CONT1 EAGLE_STBY 70 70 EAGLE_STBY CAM_-7.5V 4

7 Z_SENS_GND ND_ON 24 24 ND_ON XCS_TG_BEAR 69 69 XCS_TG_BEAR M_5V58HALL(-) ZM_RST_SENS 23 23 ZM_RST_SENS VSUB_CNT 68 68 VSUB_CNT M_5V69BIAS(-) FC_RST_SENS 22 22 FC_RST_SENS RESET_CAM/PB 67 67 RESET_CAM/PB A_4.9V 7

D 10 HALL(+) GND 21 21 GND GND 66 66 GND A_4.9V 8

11 BIAS(+) GND 20 20 GND XMACRO_PE 65 65 XMACRO_PE A_3.2V 9 12 GND GND 19 19 GND PAL/XNT 64 64 PAL/XNT A_3.2V 10 13 GND SYS_V 18 Board TO 18 SYS_V MC_A01 63 63 MC_A01 D_3.2V 11 14 DRIVE(-) CAM_SCK 17 17 CAM_SCK MC_A02 62 62 MC_A02 D_3.2V 12 Board 15 DRIVE(+) CAM_SO 16 16 CAM_SO MC_A03 61 61 MC_A03 D.2.35V 13 16 FOCUS_A CAM_SI 15 15 CAM_SI MC_A04 60 60 MC_A04 D.2.35V 14 17 FOCUS_B MC_PB12 14 14 MC_PB12 MC_A05 59 59 MC_A05 KEY_AD4 15

E 18 FOCUS_A MC_PBO9 13 13 MC_PBO9 MC_A06 58 58 MC_A06 SY-56 PAL/XNT 16

19 FOCUS_B MC_PBO4 12 12 MC_PBO4 MC_A07 57 57 MC_A07 CAM_DD_ON 17 20 F_SENS_VCC HALL_AD 11 11 HALL_AD MC_A08 56 56 MC_A08 BOARD LENS_TEMP_AD 18

CD-236 21 TH_OUT LENS_TEMP_AD 10 10 LENS_TEMP_AD MC_A09 55 55 MC_A09 HALL_AD 1922 F_SENS_GND CNT_Y99CNT_Y MC_A10 54 54 MC_A10 FOCUS_A 20

23 F_SENS_RST CNT_C88CNT_C MC_A11 53 53 MC_A11 FOCUS_B 21 BOARD 24 ND_CONT(+) GND77GND MC_A16 52 52 MC_A16 1/6 SH BLOCK(1/2) REG_GND 22Board TO25 ND_DRIVE(+) SP_VOL66SP_VOL MC_A17 51 51 MC_A17 REG_GND 23

F 26 ND_DRIVE(-) MCK1255MCK12 MC_A21 50 Board 50 MC_A21 2/6 SH BLOCK(2/2) SP_VOL 24

27 ND_CONT(-) MSHUT_ON44MSHUT_ON MC_A22 49 49 MC_A22 CNT_C 25 GND33GND MC_A23 48 48 MC_A23 3/6 MM BLOCK(1/2) CNT_Y 26

LD-98 M_5V22M_5V MC_D00 47 47 MC_D00 REG_GND 27M_5V11M_5V MC_D01 46 46 MC_D01 4/6 MM BLOCK(2/2) AOUT_L 28 BOARD 30P CN402 CN452 30P MC_D02 45 45 MC_D02 REG_GND 29MC_D03 44 44 MC_D03 5/6 CN BLOCK REC_OUT 30

MC_D04 43 43 MC_D04 REG_GND 31

G 6/6 USB BLOCKMC_D05 42 42 MC_D05 PANEL_Y 32

MC_D06 41 41 MC_D06 PANEL_R-Y 33 MC_D07 40 40 MC_D07 PANEL_B-Y 34 GND 39 39 GND MC_D08 39 39 MC_D08 REG_GND 35 CAM_15V 38 38 CAM_15V MC_D09 38 38 MC_D09 C_OUT 36 CAM_-7.5V 37 37 CAM_-7.5V MC_D10 37 37 MC_D10 REG_GND 37 A_4.9V 36 36 A_4.9V MC_D11 36 36 MC_D11 Y_OUT 38 A_4.9V 35 35 A_4.9V MC_D12 35 35 MC_D12 REG_GND 39

H A_3.2V 34 34 A_3.2V MC_D13 34 34 MC_D13

A_3.2V 33 33 A_3.2V MC_D14 33 33 MC_D14 33P CN455 GND 32 32 GND MC_D15 32 32 MC_D15 REG_GND 1 GND 31 31 GND D_2.35V 31 31 D_2.35V REG_GND 2 GND 30 30 GND D3.2V 30 30 D3.2V REG_GND 3 CAM_DD_ON 29 29 CAM_DD_ON D3.2V 29 29 D3.2V REG_GND 4 PAL/XNT 28 28 PAL/XNT A_3.2V 28 28 A_3.2V REG_GND 5 GND 27 27 GND A_3.2V 27 27 A_3.2V XSTB_OPEN 6

I RESET_CAM/PB 26 26 RESET_CAM/PB A_4.9V 26 26 A_4.9V MC_HELP 7

VSUB_CNT 25 25 VSUB_CNT A_4.9V 25 25 A_4.9V ACCES_LED 8 CAM_SO 24 24 CAM_SO CAM_DD_ON 24 24 CAM_DD_ON MC_XFLRST 9 XCAM_SCK 23 23 XCAM_SCK PS-427 GND 23 23 GND XRST_SYS 10 CLPOB 22 22 CLPOB CAM_-7.5V 22 22 CAM_-7.5V REG_GND 11 XCS_TG_BEAR 21 21 XCS_TG_BEAR BOARD MCK12 21 21 MCK12 MC_VCC 12EAGLE_STBY 20 20 EAGLE_STBY CAM_15V 20 20 CAM_15V MC_BS 13 CA_FD 19 19 CA_FD 1/2 PANEL BLOCK(1/2) GND 19 19 GND MC_DIO 14

J CA_HD 18 18 CA_HD MC_XWE1 18 18 MC_XWE1 MC_SCLK 15

GND 17 17 GND 2/2 PANEL BLOCK(2/2) MC_XWE0 17 17 MC_XWE0 MC_INT 16 MCK12 16 16 MCK12 MC_XRD 16 16 MC_XRD MC_MS_IN 17 MCK24 15 15 MCK24 MC_XCS1 15 15 MC_XCS1 SYS_V 18 CA_ADO9 14 14 CA_ADO9 MC_DREQ1 14 14 MC_DREQ1 HDO 19 CA_ADO8 13 13 CA_ADO8 MC_DACK1 13 13 MC_DACK1 XMC_CS 20 CA_ADO7 12 12 CA_ADO7 XRST_SYS 12 12 XRST_SYS XHI_SCK 21 CA_ADO6 11 11 CA_ADO6 SYS_V 11 11 SYS_V HI_SI 22

K CA_ADO5 10 10 CA_ADO5 CAM_SO 10 10 CAM_SO HI_SO 23

CA_ADO499CA_ADO4 XCAM_SCK99XCAM_SCK REG_GND 24 CA_ADO388CA_ADO3 FC_RST_SENS88FC_RST_SENS MCK12 25 CA_ADO277CA_ADO2 ZM_RST_SENS77ZM_RST_SENS REG_GND 26 CA_ADO166CA_ADO1 ND_ON66ND_ON X232C_DET 27 CA_ADO055CA_ADO0 GND55GND R1_OUT 28 GND44GND LENS_RST_LED44LENS_RST_LED T1_OUT 29 GND33GND AGC_CONT233AGC_CONT2 REG_GND 30

L AGC_CONT122AGC_CONT1 PE_DAC_LEVEL22PE_DAC_LEVEL USB_+ 31

AGC_CONT211AGC_CONT2 AGC_CONT111AGC_CONT1 USB_- 32 39P CN101 CN251 39P 80P CN252 CN451 80P REG_GND 33

FRAME SCHEMATIC DIAGRAM

4-3 4-4,

TO FRAME SCHEMATIC DIAGRAM (1/2) FP-133 FLEXIBLE

2 REG_GND 1 DC_300V 2P 40P CN601 CN003 40P GND 40 40 GND GND 39 39 GND GND 38 38 GND GND 37 37 GND GND 36 36 GND GND 35 35 GND GND 34 34 GND GND 33 33 GND A_3.2V 32 32 A_3.2V A_3.2V 31 31 A_3.2V D_3.2V 30 30 D_3.2V 1 10 D_3.2V 29 29 D_3.2V D_3.2V 28 28 D_3.2V D_3.2V 27 27 D_3.2V D_2.35V 26 26 D_2.35V CAM+15V 25 25 CAM+15V D_2.35V 24 24 D_2.35V CAM-7.5V 23 23 CAM-7.5V M+5V 22 22 M+5V PANEL_-15V 21 21 PANEL_-15V M+5V 20 20 M+5V CAM_DD_ON 19 19 CAM_DD_ON GND 18 18 GND GND 17 17 GND A+4.9V 16 16 A+4.9V A+4.9V 15 15 A+4.9V PANEL+6.5V 14 14 PANEL+6.5V LCD_DD_ON 13 13 LCD_DD_ON PANEL+4.9V 12 12 PANEL+4.9V SYS_DD_ON 11 11 SYS_DD_ON PANEL+13.5V 10 10 PANEL+13.5V STB_CHARGE99STB_CHARGE EVER_3.5V88EVER_3.5V XSTB_FULL77XSTB_FULL HI_UNREG66HI_UNREG BAT_SIG55BAT_SIG BL_UNREG44BL_UNREG BL_UNREG33BL_UNREG GND22GND GND11GND

FP-134 FLEXIBLE Ver 1.1 1999.10 DSC-F505 FRAME SCHEMATIC DIAGRAM (2)

19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

FLASH UNIT(MC) A

CN001 3P + BT901 CN002 4P 21P CN6044P BATT UNREG 1 BATTERY ST_GND11ST_GND DD-131 REG_GND 1BATT SIG2sTERMINAL BOARD CONTROL SWITCH BLOCK(PW) ST UNREG22ST UNREG REG_GND 2BATT GND 3 STB_CHARGE33STB_CHARGE BOARD D+ 3 4P CN002- -MOUNT FLEXIBLE- XSTB_FULL44XSTB_FULL D- 4 vcc 1 REG_GND 5 S003 DIGITALD- 2 USB_DET 6 POWER I/OD+ 3 B

MD-97 REG_GND 7 ON/OFF (USB)GND 4

R1_IN 8

HARNESS D007T1_OUT 9 D004

(POWER LED) REG_GND 10 (GREEN) (REC LED) POWER_LED 11 (RED) SELF_LED 12 S002 J001 D_3.2V 13 (SHUTTER) DIGITAL XPWER_SW 14 I/O C REG_GND 15 (SERIAL) XSHTR_LOCK_SW 16 MOVIE STILL PLAY

MS-114 FP-132 XSHTR_SW 17 S001FLEXIBLE MOVIE/XSTILL_SW 18HARNESS (MODE)XCAM/PB_SW 19

39 REG_GND N.C 20 38 REG_GND N.C 21 CN001 21P 37 CAM_15V D 36 CAM_-7.5V 2P CN701 35 M_5V MIC SIG 1 34 M_5V HI-70 MIC901MIC GND 2 MIC33 A_4.9V BACK-LIGHT 32 A_4.9V BOARD 5P CN605 UNIT31 A_3.2V BL UNREG11BL UNREG 30 A_3.2V 1/6 RGB BLOCK BL GND22BL GND 29 D_3.2V HB-50 E2/6 TG BLOCK BL ON33BL ON 28 D_3.2V 3/6 VI BLOCK BL PWM 4 HARNESS 4 BL PWM27 D.2.35V BL LED ON55BL LED ON 26 D.2.35V 4/6 AU BLOCK 5P 25 KEY_AD4 5/6 HI BLOCK(1/2) 24 PAL/XNT 6/6 HI BLOCK(2/2) 23 CAM_DD_ON 22 LENS_TEMP_AD 24 CLD 21 HALL_AD 23 SPD F 20 FOCUS_A 22 CTR 19 FOCUS_B CN901 30P 21 EX3 18 REG_GND 20 EX2 17 REG_GND Vss11EX3 EX2 2 19 VB12 16 SP_VOL BT601 BS23CTR VB12 4 18 RES 15 CNT_C NC35SPD RES 6 17 TST (N.C) 14 CNT_Y + DIO47CLD VR 8 16 VR 13 REG_GND NC59N.C VG 10 LCD90115 VG G 12 AOUT_L INT 6 MEMORY STICK 11 N.C VB 12 COLORLITHIUM 14 VB 11 REG_GND 13 N.C GND 14 LCD UNITBATTERY NC 7 13 GND 10 REC_OUT SCLK 8 15 N.C VSH 16 12 YSH 9 REG_GND Vcc 9 17 N.C COM 18 11 COM 8 PANEL_Y Vss 10 19 N.C VGL 20 10 VGL 7 PANEL_R-Y CN606 10P 21 N.C VSS 22 9 VSS ND901 6 PANEL_B-Y 23 VGH MO2 24 D607 8 MO2 BACK-LIGHT 5 REG_GND 25 VSH MO1 26(ACSSES) 7 MO1 H2P CN702 4 C_OUT 27 VCC EX1 28SP901 6 EX1SP_OUT- 1 3 REG_GND 29 CLS SPS 30 SP_OUT+ 2 SPEAKER 5 SPS 2 Y_OUT 4 CLS 1 REG_GND 3 VCC CN602 39P 2 VSH 1 VGH 33 REG_GND 24P 32 REG_GND I 31 REG_GND CONTROL SWITCH BLOCK(FK) CN002 18P 30 REG_GNDTW29 REG_GND 1-MOUNT FLEXIBLE- RV001 28 XSTB_OPEN CN607 30P (ZOOM) 2 27 MC_HELP 1 REG_GND REG_GND 2 CN001 330P S002 26 ACCES_LED 3 ZOOM_SW_AD SYS_V 4 REG_GND 4(FLASH) 25 MC_XFLRST 5 D_3.2V HSY 6 5D006 24 XRST_SYS 7 STB_LED PANEL_COM 8 (FLASH LAMP) SYS_V6J23 REG_GND 9 REG_GND KEY_AD3 10 HSY 7 S003 22 MC_VCC 11 AU_OUT VG 12 PANEL_COM 8 CPC PROGRAM AE 21 MC_BS 13 REG_GND HI_UNREG 14 VG 9 (FOR CHECK) 20 MC_DIO 15 REG_GND LANC_IN 16 HI_UNREG 10 19 MC_SCLK 17 REG_GND LANC_OUT 18 LANC_IN 11 18 MC_INT 19 REG_GND RF7 20 LANC_OUT 12 17 MC_MS_IN 21 V_OUT TXD 22 S001 13 16 SYS_V 23 REG_GND RXD 24 MENU RF7 14 K 15 HDO 25 REG_GND RESET 26 TXD 15(CONTROL BUTTON) 14 XMC_CS 27 KEY_AD1 VDD 28 ON OFF RXD 16 13 XHI_SCK 29 KEY_AD2 AV_JACK_IN 30 RESET 17 S004 12 HI_SI VDD 18DISPLAY 11 HI_SO S006 S005 S007 10 REG_GND LCD LCD LCD J001 9 MCK12 BACK LIGHT BRIGHT(+) BRIGHT(-) 8 REG_GND ON OFF A/V OUT (MONO) L 7 X232C_DET 6 R1_OUT 5 T1_OUT 4 REG_GND 3 USB_+ 2 USB_- 1 REG_GND CN603 33P M

FRAME SCHEMATIC DIAGRAM

4-5 4-6, FB108 R120 R119 C103 C108 C109 L101 C135 C138 C126 R112 C125 C128 C121 C123 C115 C118 C140 Q101 FB110 R111 C113 FB111

DSC-F505 Ver 1.1 1999.10

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAM

CD-236 BOARD (SIDE A) CD-236 BOARD (SIDE B)

C131 C130 C127

E R118 14

48 37 R117 1 36 C133 R109 L103 R116 R123 R115 R122 C120 Q103 C117 R114 R121 IC103 C116 15 FB103 X101 C119 13 11 10 C110

D1212 25 C101

R101 FB106 13 24 C105 C102 C124 C134 3C129 12 5 X102 10 1 C122

C FB104 4

FB105 R110 C137 R106 36 25 38 R113 R10839 IC10137 24 CN101 C1369876

B FB107 C107 IC102 2C114

11 20 R124 48 13 C112 1 12 FB109 R104 R103 R102 FB101 CL101 1

A R105

Q102 C132 IC104 C111 L102 C106 C104 1-675-583- 12 C139 0912345678910 11 For printed wiring boards • This board is six-layer print board. However, the pat- terns of layers two to five have not been included in the diagram. • Chip parts Transistor

C

B E

There are few cases that the part printed on this

diagram isn’t mounted in this model.

CCD IMAGER, CAMERA

CD-236 4-7 4-8, VOUT VDD P0/S14.8 GND RG P0/S12.6 NC H2 P0/S2.0 GND H1 P0/S-0.2 P0/S2.7 V1B GND V1A SUB P0/S8.2 V2 CSUB P0/S8.4 V3B VL P0/S-7.4 V3A H1 P0/S2.7 V4 H2 R108 24 23 22 21 20 19 18 17 16 15 14 13 36 35 34 33 32 31 30 29 28 27 26 25

CKO H1 CKI VSS3

2.4V FMC C122 1.60.01u OSCO VSS2 CM(1.5V) CLPDM B OSCI RG 1.4 P0/S0.9 AVDD2 XSHD XSHD VDD5 3.2 P0/S2.3

VDD2 XSHP XSHP 3.2 3.2AVDD3

P0/S3.1 MCKO VDD13.2 P0/S2.5 MODE1 CLPOB 1.7

SSI EBCKSM 3.2

MODE2 PBLK SCK WEN 3.2 P0/S2.7 3.2 AVDD4 STBY SEN ID 3.1 3.2 DVDD1 0 3.1AVDD5 3.2 VDI DSGAT TG_DSGAT 3.2 ADCLK 3.1AVSS4 TG_RST P0/S1.8 HDI RST 3.1 AVSS5 DVSS3 3.1

VSS6 VSS1

1.2 REFN DRVSS REFP DRVSS12345678910 11 12 37 38 39 40 41 42 43 44 45 46 47 48

VOUT VIN VSS Ver 1.1 1999.10 DSC-F505

12345678910 11 12 13 14 15 16

CD-236 BOARD A FB107 0uHCCD IMAGER,CAMERA NO MARK : STILL/PB mode

-REF.NO.:3000 SERIES- S : STILL mode FB108 0uH

XX MARK : NO MOUNT P : PB mode

R124 0 1608 R104 FB101 L102C128 C132 10uH 22 0uH C1230.1u 0.1u 47u C140P0/S2.7 C139B B 6.3V XX XX Note:Resistor are mounted TABBBCL101

B to the location where C111

FB109,FB110,FB111 are printed. FB109 (Note) 10u 0 Q102 6.3V 12 11 10987654321R113321UN9213J-(K8).SO 100k

SWITCH C138

C112 22u 1u 16V C106 B 1608 TA B C104 0.1u 0.1 VSUB_CNT R105 V2153 0.1u 22 C135P0/S1.9 10u IC104 B 1608 B 1608 C108P0/S9.0 22u H2 TEST2 20V XX 4.8 P0 TA BS-7.2 R103 C107 16VB VDD3 SUB

VSHT C 4700 0.01u TA 3.2 P0C103 B 2012 VSHT VDD4 V3B S-7.2 V3BP0 C136

0.1u R102 XSHP P0/S2.5 IC1021M XSHP VL S-7.2 0.1uF (Note) 39 GNDXSHD P0/S2.3 P0 1005 2 FB110 0 XSHD TIMING GENRATOR

F V3A S-7.2 V3A 38 CAM_15V

C114 P0/S-0.3 0.1u XRS V1B V1BP0/S2.0 B P0 37 CAM_-7.5V 1608 P0/S2.7 C137 FB111 0 PBLK IC102 S14.9 0.1u11C109

VH 36 A_4.9V

10u (Note) P0.1/S3.1 P0/S-0.3

F

11 12 13 14 15 16 17 18 19 20 CLPDM CXD2470R-T420V V1A V1A 35 A_4.9V P0/S-7.2 TA B VSS4 V4 V4IC101 34 A_3.2VR106 05 P0/S3.1 P0/S-0.3CLPOB V2D P0/S1.8678

V2 33 A_3.2V CCD IMAGER ADCLK VM 32 GND

IC101 ICX224AQ-13 VSS5 TEST1 31 GND 30 GND 109876543213TG_DSGATV4 R101 P0 P0/S-7.1 9 29 CAM_DD_ON 3300 S11.4 P0/S-7.1 V3A C113 28 PAL/XNT 0.1u P0/S-7.1 V3B B 27 GNDC101 TG_RST XX C102 P0/S-0.2 V2 25 26 27 28 29 30 31 32 33 34 35 36 26 RESET_CAM/PB 10p CH P0/S-0.2 V1A VSUB_CNT 1.8 25 VSUB_CNT

E P0

S10.5 V1B FB104 0uH R110 22 24 CAM_SO 23 XCAM_SCK C105 0.1u FB103 C117 X101 22 CLPOB P0/S11.4 0uH 0.1u

B

B 1608 4 24.375MHz(PAL) 21 XCS_TG_BEARP0/S14.8 R111 20 EAGLE_STBY Q101 3.1 R109 X102 47 19 CA_FD TO 2SC4178-F13F14-T1 L101 (NTSC) 47k PS-427 BOARD BUFFER 100uH 0 (PAL) 24.54MHz(NT) 18 CA_HD CN251THROUGH THE 17 GND

F FP1350 (NTSC)/3 (PAL) FLEXIBLE16 MCK12

Q103 UN9213J-(K8).SO FB105 15 MCK24 (SEE PAGE PAL/NTSC 0uH SWITCH 14 CA_ADO9 4-15) 13 CA_ADO8 12 CA_ADO7 11 CA_ADO6 12 11 10 CA_ADO5 9 CA_ADO4

G R112 XX 8 CA_ADO3

7 CA_ADO2 6 CA_ADO1 P0/S3.1 C129 0.1u 5 CA_ADO0B4GND C124 1u 10 3 GND 2012 B 1.0 C134 2 AGC_CONT1 1u 24 23 22 21 20 19 18 17 16 15 14 13 13 B1608 1 AGC_CONT2H CN101 39P C119 C110 0.1u FB106 0.1u B 3.2 0uH B1608 AVSS1 DRVDD P0/S0.9 0 CCD_D P0/S1.2 15 (MSB)D9 P3.2/S0.5 R119 47 CCD_R IC103 D8C116 P3.2/s1.1 R114 470.1u AVSS2 D7 C115 B P3.1/S1.0 P3.2/S1.5S/H,AGC,A/D CONVERTER R120 0.1u AGCCNT1 D6 B1608 P0.6/S1.6 P0/S1.4 R115 47AGCCNT2 D5

I AVSS3 IC103 14 P0/S1.8 R121 47D4

1.8 P0/S1.3 R116 47 LCM(1.8V) CCD1000Y-2/2K D3 • SIGNAL PATH C118 C120 3.2 P3.2/S1.3 R122 0.1u 0.1u AVDD1 D2BB3.2 P3.2/S1.7 R117 47COMPVIDEO D1

VIDEO SIGNAL AUDIO 3.2 P3.2/S0 R123 47CGAINCNT (LSB)D0

0 R118 CHROMA DVSS1 47

CHROMA Y Y/CHROMA SIGNAL C1210.1u

B 2.3 1.8

J REC 37 38 39 40 41 42 43 44 45 46 47 48

C125 C131 C133 0.1u 0.1u 47u Precautions Upon Replacing CCD imager

PBBB6.3VTA B • The CD-236 board mounted as a repair part is not equipped

C126 C127 C130 with a CCD imager.0.1u 0.1u L103 B 0.1u B 10uHB When replaching this board, remove the CCD imager from the old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section.

K • As the CCD imager may be damaged by static electricity from

its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts 09 nor exposed to strong light.

CCD IMAGER, CAMERA

4-9 4-10 CD-236, C407 R413 R414 C406 R436 Q401 C409 D401 R406 R437 C420 L401 Q405 C411 C401 R427 R433 R430 R434 R435 C418 Q403 R422 R429 R425 R402 C422 Q404 R439 R411 R403 C405R409 Q402 R404 R408 R407 R405

DSC-F505 Ver 1.1 1999.10 LD-98 BOARD (SIDE A)

26 14

F C412 IC402

1 13 R417 C403 C402 L402

E

1 20 26 14 L403 30 2 IC403 CN402 IC406 1 13 29 1

D 10 11 LD-98 BOARD (SIDE B)

C426 R426 C417 C413

C R410 R416 R432 C419 C421

C408 R412C410 1011871C424 C423 IC404 R415 L404 IC407 IC405451185

B 8 1420C425 C416R418 C415 C414 IC401

R438 D402 R428 R424 Q406 C404 R419R431 R423 R42114226 R420 CN401

A 1 27

1-675-586- 12 0912345For printed wiring boards • This board is six-layer print board. However, the pat- terns of layers two to five have not been included in the diagram. • Chip parts Transistor DiodeC6543BE12321

There are few cases that the part printed on this

diagram isn’t mounted in this model.

LENS DRIVE

LD-98 4-11 4-12, IC401 NJM2904V(TE2) OUT VCC IN(-) OUT 0.8 0.8 IN(+) IN(-) 0.8 0.8 GND IN(+) 0.8 IC403 UPD16833AGS-9JH IC402 UPD16833AGS-9JH 3.1 3.1 DGND DGND 4.9 VDD 4.9 VDD 0.3B1 B1 VM1 VM1 PGND2 0.1 PGND2 A1 A1 0.3 B2 B2 PGND1 PGND1 VM2,3 0.1 VM2,3 A2 A2 0 4.9 B3 0.1 B3 A3 A3 PGND4 PGND4 PGND3 PGND3 0 B4 0.1 B4 A4 A4 3.1 EN4 4.9 EN4 IC404 NJM2904V(TE2) VM4 VM4 NC S1–2.2/P2.6 NC IN1 IN1 0 OUT VCC IN4 0 IN4 0.9 EN1 EN1 3.1 OUT EN3 EN3 0.9 IN(-) IN2 IN2 0 IN(+) IN(-) IN3 0 IN3 EN2 EN2 GND 0.9IN(+) 0.9 IC405 BA10324AFV-E2 IC406 CXD2430N-T4 OUT 0.1 OUT 3.0 IN(-) IN(-) VDIN VDD 0.1 S3.2/P0.1 3.1 IN(+) IN(+) TEST1 SENS0 3.1 3.0 VCC GND CS SENS1 0.9 3.1 3.1 IN(+) IN(+) SCK EN1 0.9 0.9 0 3.1 IN(-) IN(-) SIN DIR1B 1.2 0.2 OUT OUT SOUT DIR1A CKOUT EN0 S0.5/P1.7 1.6 CKIN DIR0B 3.1 XCLR DIR0A VSS TEST0 1098765432111 12 13 14 15 16 17 18 19 20

TO

SY-56 BOARD (5/6) CN452 (SEE PAGE 4-32)

Ver 1.1 1999.10 DSC-F505

12345678910 11 12 13 14 15 16 17 18

LD-98 BOARD C4021608 B A R405 LENS DRIVE R403 R404 4700 ±0.5% NO MARK : STILL/PB mode 1u 10k 18k-REF.NO.:4000 SERIES- 0.9 S : STILL mode R436R409 R411 XX MARK : NO MOUNT 0 2200 P : PB mode R402 39k 120k

Q402 100k ±0.5% ±0.5% UN9213J-(K8).SO ND ON SWITCH Q406 IRIS_CONT1 2SD2216J-QR(K8).SO Q405 ND FILTER DRIVE C403 0.1u XP4316-(TX).SO IRIS_CONT2 S1.7/P0.6 4.4 B 1608 ND FILTER SWITCH R419 C426 S1.0/P3.1 0 0.7 R437 1k C415 0.1u1608 IC407

B 2200 B

0 0.01u MB88346LPFV-G-BND-ER ±0.5% B 4.8 GND S0.1/P0.63.1 R420 R438 C404 16k R425 R429 VSS 10 XX AO2 0.3

IC407

0.022u 1608 180k0 AO3 B ±0.5% AO1 0 EVR D/A CONVERTER R422 R428100k AO42700 R432 HALL_REF 0.9 DI S3.1/P0R407 4.9 180k 4.8 47k AO5HALL_GAIN 1.58765CLK±0.5% R415 C410 R423 R4300.033u 22k 180k HALL_OFFSET 1.5 AO6 0

LD

100k B 1608 R424 AO7 C409 100k C416 C414 0.001u DO 1.2 3300p B 1.2 AO8C 0.022u AO12B B 1.2 AO9 1.1 C405 R408 3.1 IC404 S0.1/P2.0 AO11 R439 0.1u 10k876514 13 12 11 10983.1 AO10 VCC 3.1 3300 B ±0.5% IRIS DRIVE VDD L404 1608 10uH 0.9 S0.3/P3.0 C423 C424 C425 0.1u CN402 30P S0.4/P1.9 10u 0.1u1234B6.3VB1M_5V 0.8 1608 TA 1608 2 M_5V

D IC405 3 GND

4 MSHUT_ON

IC401 HALL AMPS1.8/P0 5 MCK1212341234567

0.7 6 SP_VOL

ND FILTER DRIVE S1.1/P4.9 Q401 L4032SD2216J-QR(K8).SO C418 10uH 7 GND

IRIS DRIVE Q404 0.01u R413 ±10%2SD2216J-QR(K8).SOB8CNT_C 100k AMP C407 0.5 9 CNT_YR416 S1.8/P0 R410 C4081u 0.1u 47kS0.7/P0 1k B 1608 0.7 10 LENS_TEMP_AD

E 1608 R414 C413 0.1 R427 C421 C422R406 0.1u 12k R431 11 HALL_AD

10 C406 10k B R418 10k C419 0.01u 10u 1608 0.022u R421 1608 330 B 6.3V 12 MC_PBO4 B R412 22k R426 1u 4700 1200 C417 B 1608 TA 13 MC_PBO9

XX

1608 14 MC_PB12D401 MA3ZD1200LS0 15 CAM_SI V2819 16 CAM_SO C401 17 CAM_SCK 0.01u B 18 SYS_V

F ND_CONT(-) 27 19 GND

ND_DRIVE(-) 26 20 GND ND_DRIVE(+) 25 21 GND ND_CONT(+) 24 22 FC_RST_SENS F_SENS_RST 23 23 ZM_RST_SENS F_SENS_GND 22 24 ND_ON TH_OUT 21 25 AGC_CONT1 Q403 3.1 F_SENS_VCC 20 26 LENS_RST_LED

G 0FOCUS_B 19 2SA1832F-Y/GR 27 AGC_CONT2(TPL3)

FOCUS_A 18 IC402 B+ SWITCH 28 PE_DAC_LEVEL3.1 R417 4700 FOCUS_B 17 29 A_3.2V FOCUS_A 16 FOCUS/ZOOM MOTOR DRIVE 30 A_3.2V LENS DRIVE(+) 15

UNIT

DRIVE(-) 14 L401 10uH GND 13 GND 12

H R434 R435BIAS(+) 11 R433 68k 68k

47k HALL(+) 10 BIAS(-) 9 HALL(-) 8 26 25 24 23 22 21 20 19 18 17 16 15 14 C411 0.01u Z_SENS_GND7BZ_SENS_RST 6 L402 Z_SENS_VCC 5 D402 10uH MA111-(K8).S0 ZOOM_B 4 S1–2.2/P1.4

I C412ZOOM_A 3 33u S1–2.2/P2.6

ZOOM_B 10V0002TA B 20 19 18 17 16 15 14 13 12 11 ZOOM_A 1 27P CN401 C42012345678910 11 12 13 1uB12345678910

J IC406 FOCUS/ZOOM MOTOR PRE DRIVE

3.1 3.1

K 0

4.900026 25 24 23 22 21 20 19 18 17 16 15 14

IC403 • SIGNAL PATH SHUTTER DRIVE VIDEO SIGNAL L CHROMA Y Y/CHROMA

12345678910 11 12 13 REC

PB

4.9

LENS DRIVE

4-13 4-14 LD-98, S005 VDR001 VDR002 1SS387-TPL3 D014 D009 01ZA8.2(TPL3) D010 01ZA8.2(TPL3) FB004

Ver 1.1 1999.10 DSC-F505

1234567

CONTROL SWITCH

R001

A 3300 LF001 R002BLOCK(PW) 2200 CN002 4P1 VCC DIGITAL

• CONTROL SWITCH BLOCK(PW) is 2 D- I/O replaced as a block. (USB)3 D+ So that this PRINTED WIRING BOARD is omitted. 4 GND LF002 D002 D003

B 01ZA8.2 01ZA8.2(TPL3)(TPL3) DIGITAL

J001 I/O FB001 SERIAL 21P CN001 FB002 REG_GND 1 REG_GND 2 1-691-737-21 FB003 D+ 3

C D- 4

REG_GND 5 USB_DET 6 REG_GND 7 TO R1IN 8 (USE for J001 guard) SY-56 BOARD T1OUT 9 (5/6) CN604 REG_GND 10 D004 D007 (SEE PAGE POWER_LED 11 S003

D R003 R004 4-48) SELF_LED 12 680 330 POWERTLSU1008(T05,SOY) TLGU1008(T05,SOY) ON/OFF

D_3.2V 13 (REC LED(RED)) (POWER LED(GREEN)) S003 XPWER_SW 14 REG_GND 15 XSHTR_LOCK_SW 16 XSHTR_SW 17 S002 (1st) MOVIE/XSTILL_SW 18 (SHUTTER) XCAM/PB_SW 19 S107

E N.C 20 (2nd)

N.C 21 S001 MOVIE STILL PLAY (MODE) MOVIE COM PLAY LND003 LND004 LND002

F 10kR005

D008 01ZA8.2(TPL3) STATIC_GND 09 LND00112345678

CONTROL SWITCH BLOCK(CF)/MF UNIT

• CONTROL SWITCH BLOCK(CF)/MF UNIT is replaced as a block.

A So that this printed board is omitted. CONTROL SWITCH (BRIGHT LEVEL MF UNIT

SENSOR)

BLOCK(CF) Q004PN126S-R

6P CN001 CN004 6P PHOTOTR_5V11PHOTOTR_5V C004 2200p PHOTOTR_OUT22PHOTOTR_OUT BB REGGND33REGGND 1608 FOCUS_B44FOCUS_B FOCUS_A55FOCUS_A D_3.2V66D_3.2V (FAR) RV2 (MANUAL FOCUS) RV1

C (NEAR)

D_3.2V 10

S005

FOCUS_A 9

FOCUS

TO FOCUS_B 8 S001 SY-56 BOARD REG_GND 7 MACRO AUTO (5/6) S004

D CN453 REG_GND 6 (W/B SET)

(SEE PAGE PHOTOTR_OUT 5 MANUAL 4-31) PHOTOTR_5V 4 S002 S003 REG_GND 3 10k SPOT_METER WHT-BAL R006 D_3.2V 2 R001 S001 R002 R003 R004 R005KEY_AD4 1 1800 2700 S002 4700 S003 6800 S004 39k 10P CN002

E

LND1 STATIC_GND

MF UNIT/ CONTROL SWITCH BLOCK4-33 4-34 CF/PW

, R929 R930 R307 C310 D607 C315 C801 Q605 R812 C802 C191 R918 R916 R926 C909 R915 R907 D903 R908 R905 C908 R823R909 C806 C808 C311 R303 R828 L302Q303 C906 R801 R822 R827 R805 C312R804 R649 C813 C927 R910 R912 C905 R920 R908 R924 D902 C913 C902 FB701

A

C901 Q305C739 D904 R719 C733 C715 R968 C724 C744 C717 R969 R718 C726 C728 Q702 C727 C730Q706

A

C729 L706 R682 R617 R6?? R673 R657 R674 R624 C615 R626 C616 R643 R670

A A A A A A

A K

DSC-F505 Ver 1.1 1999.10 HI-70 BOARD (SIDE A)

CN702

G CN605

2 1 R60651R663 D602 C306 R681 C621 32 R622 R66139 R607 R313 C301 R611 C606 C607 R312 Q603 C620 R662

F Q302 40 2 R610 R612 Q608 Q610 Q607 8 5C302

11 10 R304 L301 C605 R635 R644 X602R650 R641 R646 R625 IC602 C624 16 R636 R645 R642 R654 19 R314 R647 IC301 39 CN601 1 R651 C622 R656 C307 C632 C618 R6341415 17 C734 R633 C633 R630

E C309 C631 C617 C619 C623 R653 C61120 1 R717 75 51

C316 C308 R819 C741 R7332176 50 C817 C725 L704 R305 CN602 R723 R703 24 13 C805 C803 C816 R820 R818 Q304 R732 C303 C318 C703 25 12 R704R714 C723 C612 C804 R817 R821 R824 1 D304 L303 L801 12 1 C317 C701 C704 R706 IC803 C610

D 13 48 R702

R715 18R62768R701 IC702 R626 32 33 IC603 C807 7 R706 C731 R672 5 C614 C613 IC802 C712 4 36 1 C732 R707 L80231Q705 C711 37 48C745 R680 2 R729 R725 R712 24 37 C735 R709 R705

C R80625 36 R726 R720L901 C713C810 C811 C724 100 26C714

12 1 C721 C743 1 25 C716 R658 R660 R671 R677 1 C904 Q704 R637 L902 L701 A R639 CN603 Q701R711 R713 R618 R659 R67613 12 C702 IC801 R721 D604 R613 R928 C740 R609 R61412 1 R967 R676 BT601

B R63613 48 30 2 30 2

R608 13 24 14 R981 IC901 C918 R939 R938 R922 FB901 R94411 29 CN901 1 29 CN60710 1R921 R976 R943

A594C907 24 37 R941

C917 IC902 25 36 L905 L903 R942 FB607 FB606 R913 R914 C903 R982 R980 R979 1-675-584- 12 0912345678910

For printed wiring boards

• This board is six-layer print board. However, the pat- There are few cases that the part printed on this terns of layers two to five have not been included in diagram isn’t mounted in this model. the diagram. • Chip parts

Transistor

C54BE1234-35

LCD DRIVE, TIMING GENERATOR, VIDEO, AUDIO, HI CONTROL

HI-70 4-36, Q604 R648 R623 R679 X601 Q609 R668 R669

A

C608 R675 IC601 IC606 C630 C816

A

C815 C915

A A Ver 1.1 1999.10 DSC-F505 HI-70 BOARD (SIDE B)

Q611 Q612

G F

R605 13 1454IC60781LND001

E R667C609 R604

D606 LND002 1 CN606 R621 R620 1 D608 R619

D

R618

C B 11 12

1 2 R738 R726 2 20 C814 C812 C6293241R727 R742 FB605 C813 R93254R93332121CN701 R934 R935A CN604 IC605 L60141C920 Q905 Q906 Q903 Q90413C819 1-675-584- 12 0912345678910 For printed wiring boards • This board is six-layer print board. However, the pat- There are few cases that the part printed on this terns of layers two to five have not been included in diagram isn’t mounted in this model. the diagram. • Chip parts TransistorC654BE1234-38

LCD DRIVE, TIMING GENERATOR, VIDEO, AUDIO, HI CONTROL

4-37 HI-70, 24 23 22 21 20 19 18 17 16 15 14 1312345678910 11 123214548 47 46 45 44 43 42 41 40 39 38 37 COM_ADJ COM_BLK_LVL

PICTURE

COM_AMP 3.1 Y/CR/XRGB_SW GAMMA2 1.1 0.8 AGC_FIL GAMMA0 0.8 AGC_OUT SUB_BRT_R 2.3 BRT_R 0 AGC_LVL SUB_BRT_B 2.3 BRT_B 1.2 COLOR RGB_AMP AMP H_FIL_IN FRP 2.4 FRPV G/Y 2.0 COM_FRP 2.4 FRPT 2.0 R/R-Y/CR 2.4OUT_LIM B/B-Y/CB 2.0 VSH H_FIL VCC2 4.9 REG_OUT 13 14 15 16 17 18 19 20 21 22 23 24 4.6

DSC-F505 Ver 1.1 1999.10

12345678910 11 12

HI-70 BOARD(1/6) A LCD DRIVE (RGB BLOCK)

-REF.NO.: 2000 SERIES-

XX MARK : NO MOUNT NO MARK : STILL/PB mode R806

47k TO (5/6) 1 PANEL_6.5V

B

C815 R804 R827 R823 10u 22k 15k 12k 10V L802 TA A 10uH R805 R822 8R828 39k P_4.9V TO (2/6) L801 12k 33k 100uH A_3.2V P_3.2V 9 TO (2/6) C811 TO (5/6) 2 0.1u D_3.2V IC801

C I/O EXP(EVR) C808 1.9 6.5 C810IC801 C807 0.1u 10u

C801 47u 36 35 34 33 32 31 30 29 28 27 26 25MB40D001PFV-G-BND-ER 10V 0.1u 6.3V TAAB3.1 TA B P_MUTE

VDD

3.1 3.1 BRT_TST 2 C802 3.2 VCC 2.5 0.1u H_REV B BL_LEVEL 3.2 H_REV C806 COM_BLK B_OUT VB 10 TO (2/6) 1.8 2.0 C812 V_REV V-COM 0.1u 1uV-COM 3.2 XTEST B_DC_DET 2.5 1608 3.2 V_REVD 1.2 BRIGHT 1 IC802 G_OUT VG 10 TO (2/6), (5/6) NTSC VCO VCO 1.9 2.1 C813 1u 3.2 NTSC 0.9 COM-O 2.0 CONTRAST LCD DRIVE G_DC_DET 2.5 1608 COMTST COM_ADJ COM_ADJ COM_OUT R_OUT VR 10C814 TO (2/6) COMTST R801 3.2 IC802 2.0 1u 0 2.3 0 SUB_CON_B 4 R_DC_DET AMP IR3Y37A4 1608 XHI_SCK RGB_AMPCLK SUB_CON_R GND1 COM-O 2.9 2.0 COM-O 11 TO (2/6) TO (5/6) 3 CONT VCC1 5 GND2 FRPVHI_SO SI 3.1 FRPV0.1 1.8 OSD_B SYNC_OUT 3.1 FRPT 12 TO (2/6) BRT_B BRT_B FRPT SO 2.3 OSD_G SYNC_IN

E 13TO (5/6) 4 XCS_PANEL_D/A BRT_R BRT_R OSD_R 8 EXT_BGP P_XHD TO (2/6)

3.0 XEN 4.976COLOR COLOR BLACK_IN SYNC_SEP 3.1 VDDA IC8031.1 BRIGHT TC7SH32FU-TE85R VSS COMTST0 COMTST 1.9 NTSC 3.1 4.9 NTSC V_REV 14 TO (2/6) 12345678910 11 12 V_REV H_REV 4.9 H_REV V-COM

F V-COM 15 TO (2/6)TO (2/6) 5 WIDOV R817 VCO

R818 R820 16 TO (2/6)

IC803 XX XX C817

10k VCO

COLOR

2.2u 10V

OR GATE R819 R821 TA

XX0AR812100k TO (5/6) 6 REG_GND REG_GND 6 TO (2/6) R824 C816 C803 0.01u 180k 0.1u PANEL_Y C804 0.01u PANEL_R-Y

G TO (5/6) 7 C805 0.01uPANEL_B-Y

• SIGNAL PATH

VIDEO SIGNAL H CHROMA Y Y/CHROMA REC PB LCD DRIVE

HI-70 (1/6) 4-39 4-40,

VCO

D903 1T369-01-T8A 48 47 46 45 44 43 42 41 40 39 38 37 2.4 4.9 2.4 BLKI VSEPC R924 BLKO 33k ±0.5% 2.5 P15 4.6 BGPO MUT 3.0 4.7 HSY PDP 4.9

VSY

GND 2.5

VIN VDD

0.5 GND TST2 4.94321R928 SYNOXX TST1 4.9 0 WIDOV OSCI 4.9 FRPV WIDOT OSCO 2.4 FRPT 2.4 FRPV TESTO 2.3 FRPT56782.4 13 14 15 16 17 18 19 20 21 22 23 24 V-COM COM-O PANEL_COM R967 47 VG R968 47 VB R969 47 VR

Ver 1.1 1999.10 DSC-F505

12345678910 11 12 13 14 15 16 17

HI-70 BOARD(2/6) A TIMING GENEREATOR

(TG BLOCK) -REF.NO.: 2000 SERIES-

XX MARK : NO MOUNT IC902 COM AMP NO MARK : STILL/PB mode L901

10uH TO(5/6) 17 PANEL_13.2V L902 R941 TO(5/6) 18 R934 0B PANEL_-15.3V 10uH 33k IC902 R933 13.4 ±0.5% C909 NJM062V(TE2) 13.4 100k R905 R907 0.1u 9 1.7 680k XX 2012 3.9 Q905VCC+ 13.4 2SD1819A-QRS-TX R942 C917 C918 R913 OUT1 1.4 COM DRIVE 22k 0.01u 0.1u 10k R9292.5 ±0.5% C911 OUT2 100k 560p IN1- Q904 0.4 R915 CH 2.4 2SB1218A-QRS-TX 1M IN2- 1.4 1.3 COM DRIVEIN1+ 0.4 C916 R943 C919 1u C920 C907 -10.2 6.8u 33k 35V 1u 0.001u IN2+ -10.1 16V ±0.5% TA A 3216 R918 VCC- A1.0 TA

C TO(1/6) 8 P_4.9V 68k R921L905 68k6.8uH Q903

L903 2520 2SD1819A-QRS-TX R944 10uH R916 Q90622k COM DRIVE 2SB1218A-QRS-TX 22k ±0.5% -10.2 COM DRIVE TO(5/6) 19 PANEL_4.9V R914 R922 R981 R926 D904 1M 47k 4700 4700 R930 R932 33k 100k MA8047-H-TX R908 R909 C906 C9080.1u R935 R939 C915 82p R938 1u120k XX 0 33k 100k C902 1608 CH 3216 3.3u C904 C901 20V 0.1u XX TA A 1608 6.3VD TA A TO(5/6) 6 REG_GND CN901 30P LCD901 TO(1/6) 9 P_3.2V 1 EX3 2 EX2 3 CTR 4 VB12

E 5 SPDVB

VB 6 RES VG C903 VG 0.1uTO(1/6) 10 7 CLDVR VR C927 8 VR R979 R980 2200p 68k ±0.5% 9 N.C PANEL_COM 47k TO(5/6) 21 PANEL_COM 10 VG 11 N.C TO(1/6) 15 V-COM R982 V-COM XX 12 VB 36 35 34 33 32 31 30 29 28 27 26 25 COLOR

F 13 N.C LCDTO(1/6) UNIT11 COM-O COM-O 14 GND

15 N.C TO(1/6) 16 VCOVCO R978 16 VSH 47k 2.8 NTSC 11 2.2 FB90110 0uH 17 N.CNTSC SYNI CLD COMTST 0.5 18 COM

COMTST

TO(1/6) 14 SYNC SPDV_REV 4.9 2.4 19 N.C V_REV WIDE H_REV IC901 CTR 0 20 VGL H_REV

G NTSC 3.2

PDPC EX3

LCD TIMING GENERATOR 4.9 21 N.C FRPV

FRPV 3.0 NTPC1 EX2 22 VSS FRPT R906TO(1/6) 12 FRPT XX R910 XX 4.9 TESTI TESTOIC901 23 VGH V_REV 3.2 TEST LZ9GH234 RES 2.4 24 MO2 R912 100k 4.9 VREVC MODE2 4.9 25 VSH H_REV 3.2 TESTI MODE1C905 4.9 26 MO1 0.1u HREVC EX1 1608 COMTST 0 27 VCC D902 XX 0 COMTST 13 SPS 4.8 28 EX1 TO(5/6) 22 HDO LOWI 12 CLSH 29 CLS4.8 14 3.9 30 SPS TO(5/6) 23 SYS_V12345678910 11 12 • SIGNAL PATH

I R920 VIDEO SIGNAL68k

±0.5%

CHROMA Y Y/CHROMA

C913 82p CH REC TO(1/6) 13

PB

P_XHD

J

TO(5/6) 24 HSY TO(1/6) 5 WIDOV

TIMING GENERATOR

4-41 4-42 HI-70 (2/6), IC301 NJM2538BV(TE2)

CLAMPREF

YIN1 CIN1 C312 C311 GAINCTL/MUTE XX B 0.1u B GAINCTL/PWSAVE YIN2 CIN2/INSEL R303 CLAMP 1M V+2

CHARA

V+1

BLANK COUT WIDE SDCOUT GND

VOUT S2.0/P1.6

YOUT VSAG

YSAG S1.8/P1.5

DSC-F505 Ver 1.1 1999.10

12345678910 11

HI-70 BOARD(3/6) A VIDEO(VI BLOCK) NO MARK : STILL/PB mode

-REF.NO.:2000 SERIES- S : STILL mode

XX MARK : NO MOUNT • P : PB mode SIGNAL PATH VIDEO SIGNAL

R313 XX CHROMA Y Y/CHROMA

B TO (5/6) 2 A_3.2V REC

L301 47uH PB TO (5/6) 33 A_4.9V L302 10uH 4.8 3.2 R312 Q302

C 22k 2SD2216J-QR(K8).SO REG.

3.8 TO (5/6) 25 VOUTON TO (4/6) 26 REF3.2V CNT_C TO (5/6) 27

D C308CNT_Y 1u C316

B C310 100u C303 1608 0.1u 4V 0.1uBCTAB2V_OUT 30 TO (5/6) R307 C_OUT 1.8 1.3 3.2 4.8 68 20 19 18 17 16 15 14 13 12 11 C31522u 4V A TA REG_GND 31 TO (5/6)

E

28 15 16

IC301

TO (5/6) VIDEO AMP C304 1u 1712345678910B 1.5 1.3 1.3 1.3 Y_OUT

F C318 1608

XX C317 CH XX

CH

R305 R314 L303 XX XX

XX

C313 10u 10V

A

C301 TAC306 C309 R304 33u 47u C307 1k 10V C302 6.3V 0.1u 0.1u TA 1.30.1u TABBBBQ304B0

XX G Q303TO (5/6) 29 PAL/XNT SWITCH UN9213J-(K8).SO SWITCH

Q305

XX SWITCH VIDEO

HI-70 (3/6) 4-43 4-44, 36 35 34 33 32 31 30 29 28 27 26 25

STBY

2.4 GAIN_SET

VREF

R728 0 MIC_OUT MIC_OFF C721 WIND_ON R725 0.1u B R724 XXVCC 1k R720 MIC_IN NC 100 2VOUT PB_IN VREG_C B C743 NC 1608 1u VREF_H

AGND VCCH

4.9 VOL_CTL

GND NC

LINE_OUT 2.4 VOL_OUT 3.1 SP_SAVE BUF_IN SP_VCC12345678910 11 12 C733 0.47u

B Ver 1.1 1999.10 DSC-F505

12345678910 11 12 13 14 15 R717 22k 3.8 Q705

HI-70 BOARD(4/6) 2SA1586YG-TE85L3.2 REF 3.2V REG A AUDIO (AU BLOCK) BEEP

-REF.NO.: 2000 SERIES-

XX MARK : NO MOUNT C735 NO MARK : STILL/PB mode 10u 36 TO(5/6)

6.3V

S : STILL mode AU_SPON P : PB mode TA P XAU_MUTE B

R719 47k SP_VOL 37 TO(5/6) FB701 0uH C739 0.01u

C B

R714 68k TO(5/6) 32 REG_GND

D

R718 C734 2200 1u

B

C725 0.47u B 1608 TO(5/6) 35 AOUT_L C740 1u

E B

CN702 2P 1 SP_OUT- SP901 2 SP_OUT+ SPEAKER TO(5/6) 33 A_4.9V L70610uH M_5V 38 TO(5/6)

F L701

10uH C70210V 10u IC702 A_3.2V 2 TO(5/6) C744 C730 0.01u L70410u

LINE AMP, 3.2 10uHB 6.3V SPEAKER AMP C741

TO(5/6) 34 REC_OUT 10u 6.3V TA P C726 0.47u B 1.6 3.2 1.6 1.3 16082.4 3.2 2.2 C723XX 5.0G 24 23 22 21 20 19 18 17 16 15 14 13 B Q706 UN9215J-(K8).SO 3.1 1.6 B+ SWITCH C701 C703 2.2 R704 0.022u 0 R723 0BUF_OUT 5.0 B 1608 1608 0 REC_OUT 2.2 4.91.6 SLPF_IN R706 4.3 HPF_BIAS XX Q704 R703 XX 1.6 SLPF_OUT R732 XX FMMT617TA LPF_IN B+ SWITCH 1.6 MIX_IN 2.2 R7330 4.3 HPF_OUT 1.6 1608BEEP_IN 2.2 C711 6.3V HPF_IN 4.7u TA P 1.6H AGND 2.2AGC_OUT IC702R702 AN2904FHQ-EB 2.2 R715 3300 MIX_OUTGND 2200 R721 R701 ±0.5% R708 47k 0 2.2SPA_IN C729 470 3300 C712 AGC_DET 10uS1.6/P0 REF3.2V 261u TO(3/6)WHPF_OUT VREF_SP 2.2 6.3V ±0.5% C704 6.3V R709 S1.6/P0 2.2 TA P C7310.01u TA P 2.4 SP_OUT- R707 56k WHPF_BIAS 0.01u B 27k 1.6 2.4 SP_GND

B

1608 ±0.5% WHPF_IN 3.1 2.4 2.4 ±0.5% C713 SP_OUT+ C732 AU_OUT 39 TO(5/6) 0.015u LING_IN 0.01uBB1608 2.2 C727

I C716 10u XX

B 37 38 39 40 41 42 43 44 45 46 47 48 10V REG_GND 32 C714 1005 2.4 TO(5/6)4.3 0.015u R711 15k B XX R729 1608 ±0.5% R705 C715 2200 0.01u

B

J C717 C724 SIGNAL PATH10u 10u S3.2/P0

6.3V 6.3V TA P AUDIO SIGNAL C745 R712 C728 R713 0.1u 2200 10u 0 100k B 6.3V Q702 TA P UN9113J-(K8).SO

REC

S-0.2/P3.2 3.2 MUTE Q701 PB UN9216J-(K8).SO MIC901 R726 MUTEK 2P CN701 1200 MIC SIG 1

MIC

MIC GND 2 C742 R727 C738 XX 0 XX

AUDIO

4-45 4-46 HI-70 (4/6), 10 1

A_3.2V D_3.2V DSC-F505 Ver 1.1 1999.10

12345678910 11 12 13 14 15 16 17

A HI-70 BOARD(5/6) 30P CN607REG_GND 1

REG_GND 2 ZOOM_SW_AD Note : Note :

CONNECTOR (HI BLOCK(1/2)) ZOOM_SW_AD 3 SYS_V

SYS_V 4 D.32V The components identified by Les composants identifiés par une -REF.NO.: 2000 SERIES- D_3.2V 5

XX MARK : NO MOUNT HSY 6 HSY 24 TO (2/6) mark ! or dotted line with mark marque ! sont critiques pour la STB_LED

STB_LED 7

NO MARK : STILL/PB mode PANEL_COM 8 PANEL_COM 21 TO (2/6) ! are critical for safety. sécurité. B REG_GND 9 KEY_AD3 Replace only with part number Ne les remplacer que par une

KEY_AD3 10 FB606 AU_OUT 11 AU_OUT 39 TO (4/6) 0uH specified. piéce portant le numéro spécifié. VG 12 VG 10 TO (2/6) TO REG_GND 13 CONTROL SWITCH HI_UNREG 14 BLOCK(FK) CN001 REG_GND 15 LANC_IN 16 LANC_IN 42

C (SEE PAGE TO (6/6)

REG_GND 17 4-55) LANC_OUT 18 LANC_OUT 43 TO (6/6) REG_GND 19 RF7 20 RF7 44 TO (6/6) FB607 V_OUT 21 V_OUT 30 0uH TO (3/6) TXD 22 TXD REG_GND 23 RXD 24 RXD 45 TO (6/6)

D REG_GND 25

RESET 26 RESET KEY_AD1 KEY_AD1 27 VDD 28 VDD 46 TO (6/6) KEY_AD2 KEY_AD2 29 AV_JACK_IN AV_JACK_IN 30 LAND002 MECA_GND

E 21P CN604

10P CN606 REG_GND 1 Vss 10 REG_GND 2 Vcc 9 USB_D+ MC_SCLK D+ 3 SCLK 8 USB_D- D- 4 NC 7 MC_INT REG_GND 5 INT 6 FB605 USB_DET MEMORY STICK USB_DET 6 NC 5 MC_DIO 0uH REG_GND 7

F DIO 4 R1_INR1_IN 8

NC 3 T1_OUT MC_BS TO T1_OUT 9BS 2 CONTROL SWITCH Vss 1 BLOCK(PW) REG_GND 10 PWR_LED (SEE PAGE POWER_LED 11 XSELF_LED 4-34) SELF_LED 12LND001 D_3.2V 13 MECA_GND XPWR_SW XPWR_SW 14 33P CN603

G REG_GND 1 REG_GND 31 TO (3/6)

REG_GND 15 XSHTR_LOCK_SW USB_- 2 XSHTR_LOCK_SW 16 XSHTR_SW USB_+ 3 XSHTR_SW 17 MOVIE/XSTILL_SW REG_GND 4 MOVIE/XSTILL_SW 18 XCAM/PB_SW T1_OUT 5 XCAM/PB_SW 19 R1_OUT 6 N.C 20 X232C_DET 7 X232C_DET 47 TO (6/6) N.C 21 REG_GND 8

H MCK12 9 REG_GND 6 TO (6/6)

REG_GND 10 HI_SO R608 HI_SO 11 HI_SI D607 HI_SI 12 XHI_SCK CL-220UR-C-TS XHI_SCK 13 XMC_CS ACSSES XMC_CS 14 1.9 HDO 15 HDO 22 TO (2/6)SYS_V Q605 UN9213J-(K8).SO SYS_V 16 0MC_MS_IN LED DRIVE

I MC_MS_IN 17 MC_INT

MC_INT 18 MC_SCLK ND901 MC_SCLK 19 MC_DIO (BACK-LIGHT) MC_DIO 20 MC_BS Q611 4.9 5.0 MC_BS 21 XP4113-TXE MC_VCC 22 SWITCH CN605 5P REG_GND 23 XRST_SYS BACK BL UNREG10XRST_SYS 24 XFL_RST LIGHT BL GND20UNIT 0 BL_LED_ON

J MC_XFLRST 25 (FOR LCD) BL ON 3 0

ACCES_LED 26 HB-5000Q612MC_HELP BL PWM 4 R606 HERNESS XP4213-TXE MC_HELP 27 120KEY_AD0 BL LED ON 5 SWITCH XSTB_OPEN 28 R649 REG_GND 29 47k BL_ON REG_GND 30 XBL_PWM REG_GND 31 REG_GND 32

K REG_GND 33TO

SY-56 BOARD (5/6) CN455,456 40P CN601 REG_GND 39 REG_GND 32 TO (4/6) GND 1 TO (1/6)THROUGH THE HI_SO FP-133 HI_SO FLEXIBLE REG_GND 38 GND23XHI_SCKCAM_15V XHI_SCK CAM_15V 37 BL_UNREG 3 (SEE PAGE CAM_-7.5VCAM_-7.5V 36 BL_UNREG 4 4-31) M_5V BAT_SIGM_5V 35 BAT_SIG 5 M_5V 34 HI_UNREG 6 HI_UNREG 40

L TO (6/6) XSTB_FULA_4.9V 33 XSTB_FULL 7

A_4.9V 32 EVER_3.5V 8 EVER_3.5V 41 TO (6/6) A_3.2V STB_CHG A_3.2V 31 STB_CHARGE 9 A_3.2V 30 PANEL+13.5V 10 PANEL_13.2V 17 TO (2/6) D_3.2V SYS_DD_ON D_3.2V 29 SYS_DD_ON 11 D_3.2V 28 PANEL+4.9V 12 PANEL_4.9V 19 TO (2/6) D_2.35V LCD_DD_ON D.2.35V 27 LCD_DD_ON 13 D.2.35V 26 KEY_AD4 PANEL+6.5V 14 PANEL_6.5VM 1 TO (1/6)KEY_AD4 25 A+4.9V 15 PAL/XNT 24 CAM_DD_ON PAL_XNT 29 TO (3/6)(6/6) A+4.9V 16 A_4.9V 33 TO (3/6), (4/6) CAM_DD_ON 23 LENS_TEMP_AD GND 17 LENS_TEMP_AD 22 HALL_AD GND 18 CAM_DD_ON HALL_AD 21 FOCUS_A TO CAM_DD_ON 19 DD-131 BOARD FOCUS_A 20 FOCUS_B CN003 M+5V 20 FOCUS_B 19 THROUGH THE PANEL_-15V 21 PANEL_-15.3V 18 TO (2/6) FP-132 REG_GND 18 FLEXIBLE M+5V 22 M_5V 38N TO (4/6) CAM_-7.5VREG_GND 17 CAM-7.5V 23 D_2.35V SP_VOL 16 SP_VOL 37 TO (4/6) (SEE PAGE D_2.35V 24 VOUTON CNT_C 15 CNT_C 4-54) CAM_15V TO (3/6) 25 VOUTONCAM+15V 25 CNT_Y 27CNT_Y 14 TO (3/6) D_2.35V 26 REG_GND 13 D_3.2V 27 D_3.2V 2 • SIGNAL PATH TO (1/6), (6/6) XCS_PANEL_D/AAOUT_L 12 AOUT_L 35 TO (4/6) D_3.2V 28 TO (1/6) 4 XCS_PANEL_D/A REG_GND 11 D_3.2V 29

VIDEO SIGNAL AUDIO SYS_V O REC_OUT

10 REC_OUT 34 TO (4/6) D_3.2V 30 TO (2/6) 23 SYS_V

SIGNAL REG_GND 9 A_3.2V 31 A_3.2V 2CHROMA Y Y/CHROMA TO (1/6), (4/6)

PANEL_Y 8 PANEL_Y A_3.2V 32 PANEL_R-Y 7 PANEL_R-Y 7 TO (1/6) GND 33

REC

PANEL_B-Y 6 PANEL_B-Y GND 34 AU_SPON AU_SPON REG_GND 5 GND 35 REG_GND 6

PB TO (1/6)C_OUT 4 C_OUT GND 36 BEEP

REG_GND 3 GND 37 TO (4/6) 36

BEEP

28 TO (3/6) Y_OUT 2 Y_OUT GND 38 XAU_MUTE

P XAU_MUTEREG_GND 1 GND 39

09 39P_CN602 GND 40

HI CONTROL (1/2) TO_HI-70_BOARD(6/6) A HI-70 (5/6) 4-47 4-48

,

GND

3.9

VIN

3.1

VOUT

43431212R609 470k R637 XX R638 XX R614 470k R615 470k R639 470k R613 100k R616 100k R678 47k 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10987654321C612 0.01u B C613 0.1u B C614 XX B XCS_PANEL_D/A 3.1 26 XCS_PANEL_D/A XRST_MELODY 100 27 XCS_MELODY (EVF_DD_ON) 99 3.1 XFL_RST SYS_DD_ON 28 (XCS_EVF_D/A) XRST_FLASH 983.1 3.1 AU_SPON 29 SYS_DD_ON SP_ON 97 AV_JACK_IN 3.0 30 AV_JACK_IN WIND_FIL_SEL 96 0 3.1 R680 0 XCS_EEPROM X232C_DET XSTB_FUL 31 (XCS_EEPROM) 953.0 0 VOUTON 32 XSTB_FUL VOUTON 94 0 STB_CHG 33 NC STB_CHG 93 3.2 34 NC DD_OUT_DET 92 0 R682 2200 HALL_AD 35 NC HALL_AD 9100MELODY LENS_TEMP_AD36 LENS_TMP_AD 90 0 1.5 R672 1k ZOOM_SW_AD 37 (TEST MODE) ZOOM_SW 89 3.1 R628 470k R627 470k 38 XRESET GNDR626 88 47k 3.139 GND BACKUP_VCC 87 1.8 3.1 40 20MHZ_OUT BACKUP_VCC 86 1.6 3.2 41 20MHZ_IN (KEY_AD7) 85 3.1 3.2 BL_ON 42 BACKUP-VCC (KEY_AD6) 840 3.2 HI_SI 43 BL_ON KEY_AD5 832.7 3.2 R651 1k R650 1M KEY_AD4 44 HI_SI KEY_AD4 82 HI_SO 0.1 3.2 R636 1k R635 10k KEY_AD3 45 HI_SO KEY_AD3 81 XHI_SCK R643 10 2.9 3.2 R642 1k R641 10k KEY_AD2 46 XHI_SCK KEY_AD2LCD_DD_ON 803.1 3.2 R645 1k R644 10k KEY_AD1 47 LCD_DD_ON KEY_AD1 79 0.3 3.2 R647 1k R646 10k KEY_AD0 48 BATT_SI KEY_AD0 78 0.3 3.1 XMC_CS 49 BATT_SO BACKUP_VCC 77R670 0 2.8 3.1 50 (XMC_CS) BACKUP_VCC 76 C631 XX B 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 C632 XX B C617 XX B C618 XX B C619 XX B R625 100k R654 330k 100k D606 R667 1SS387-TPL3 0.1 CS VSS 3.0 XSCK XOUT 3.0 SIO XIN 0.2 VDD CLK_OUT 3.0 1.5 S-3513BEFS-TB IC602 BAT_SIG R604 470k43215678C609 0.1u

B

R605 100k

NC EN Ver 1.1 1999.10 DSC-F505

18 19 20 21 22 23 24 25 26 27 29 30 31 32 33 34 35 36 37

HI-70 BOARD(6/6) HICONTROL (HI-BLOCK(2/2)) A

-REF.NO.: 2000 SERIES-

XX MARK : NO MOUNT NO MARK : STILL/PB mode S : STILL mode P : PB mode TO (5/6) 40 HI_UNREG

R675 B

IC605 C630XX IC606B S-80820ANNP-EDH-T2

+3.1V REG N.C. Vdd D_3.2V 2 TO (5/6) 3.1 IC605 Vss XRESET RN5RZ31BA-TL 3.1

TO (5/6) 41 EVER_3.5V 3.9 C

5 4 IC606

RESET

L60112310uH±10% IC601 S-80827HNNP-A9A-T2 C608 22u C629 6.3V N.C. Vdd C610 33u 3.1 D 10V TA A Vss XRESET 0.1u TA 3.1 B

B TO (5/6) 6 REG_GND IC607 EEPROM IC601

IC607 AK6440BH-E2

RESET 3.2XCS_EEPROM VCC

XHI_SCK CS3.0 N.C E HI_SO SCK2.9 RST HI_SI DI0.1 GND 3.1

DO TO (5/6) 42 LANC_IN R617 2.7

100k C622 0.1u

B TO (5/6) 43 LANC_OUT 0 3.1LANC_IN BACKUP_VCC R656 XEEPROM_WE

0.3 1M LANC_OUT GND R633 FOCUS_BTO (5/6) 29 PAL/XNT 0PAL (FOCUS_B) C627 1.5 100k F SIRCS_IN XDRY_BATTXX 2.9 C624B R634 D604 N.C BATT_SENS 0.1u B 100k0 FOCUS_A N.C (FOCUS_A) RTS_SCK C6231SS388(TPL3) 3.1 3.1 R668 C633 RTS_SCK XLI_PRE_END 0.1u0.1u RTS_SIO 3.0 470kBBUSB_DET RTS_SIO USB_DET XRST_SYS R673 1k 3.2 IC603 MC_HELP XRST_SYS MC_HELP XAU_MUTE S3.2/P0 3.1 0 XAU_MUTE HI CONTROL NC Q610 BL_LED_ON 0 2.8 R630 BL_LED_ON CHARGE_INH UN9213J-(K8).SO XEEPROM_WE 3.1 1M LED DRIVER XSELF_LED G XEEPROM_WE IC603 SYS_V 3.5 GND S579615PZ-TEB NC XPWR_SW R657 1k 3.0 SYS_V XPWR_SW NC XCAM/PB_SW R658 1k S0/P2.9 XCAM/PB_SW BATT_IN XSHTR_SW R659 1k 3.0 3.1 3.1 XSHTR_SW POWER_LED Q608 XSHTR_LOCK_SW R660 1k 3.0 0 XSHTR_LOCK_SW MELODY_ENV UN9213J-(K8).SO MC_MS_IN 3.2 0 LED DRIVER PWR_LED MS_IN/DISK_IN SELF_LED 0 0.1 XBL_PWM VERTICAL XBL_PWM 3.0 S3.1/PO S3.1/P0 H XHAND_SENS STB_LED MOVIE/XSTILL_SW Q607R671 1k 0 XSTILL/MOVIE_SW 18 (REC_LED) UN9213J-(K8).SOXMC_CS 2.6 LED DRIVER STB_LED XMC_CS GND XCS_EEPROM R676 XX 3.1 S0.1/P1.8 XCS_EEPROM 32KHZ_OUT RTS_CS R677 XX 0.1 1.3 RTS_CS 32KHZ_IN CAM_DD_ON S3.1/P0 3.1 CAM_DD_ON BACKUP_VCC

I

R653 100k 19 32.768kHz R648 X602 1M C611 22p

CH J

4321R674 470k X601 20MHz 0.5 R624 1k IC602 R618 470k R619 100k R620 100k TIMER CLOCK R621 100k K Q603 XX 3.2 0 MODULATOR R623 R6795678XX XX R622 C6200 R681 2700 0 0.1uR607 R610 R611 B BEEP 0 4700 10k00C621R612 XX XX 1608 RTS_SIO BT601 R662 10k RTS_SCK C605 C606 C607 Q604 C615 C616 LITHIUM 0.001u 3.3u XX UN9213J-(K8).SO 0.022u 0.1u R661 10k RTS_CS BATERY 16VBLBTA MODULATORBBD602 R663 1SS388(TPL3) 270 Q609 HN1L02FU(TE85R) IF BLOCK 3.1

M

RF7 44 TO (5/6) 2.7 TXD 0.3 RXD 45 TO (5/6) 3.3 0.3 09 RESET

TO HI-70 BOARD(5/6) A VDD 46 TO (5/6)

R669 D608

TO (5/6) 47 X232C_DET 100k MAZS082008SO HI CONTROL (2/2)

4-49 4-50 HI-70 (6/6), Q02023R054 C019 IC002 C036 C053 R067 R065 L011 Q025 R066 Q021 R068 Q017 C052 L010 C060 C046 C042 R060 C039 Q006 R069 C058 Q003 R074 R026 Q033 R077 L015 C018 Q009 L013 C028 Q011 R036 C013 R045 R044 C025 C038 R025 R023 R024 R032 R042 R047 R043 R040 C007 C009 R016 R034 C004C005 R011 R030 R014 R015 C001 C003 R022 C006 R021 R007

DSC-F505 Ver 1.1 1999.10 DD-131 BOARD (SIDE A)

R071 D007 D0011 1

I C0325454

L003 R072 T002 T003 CN002 C027 Q012 C026C0248181

H R057 Q005 C040

4 1 L001 C034 R062 Q010 C017 C029 CN001 PS0011 4 L005 1 C020 R058 R05631PS0032 C035 C04535C016G L002151Q022 LND001 PS004 PS002 L004 T001 C015 R075 LF001 C023 C04384

F R055 E DD-131 BOARD (SIDE B)

R050 R035C008

D R051

R061 Q004 1 C047R063 D004 C0411 R049 C012 Q015 Q013 Q008 Q023 R027 C014 R04111C022 D005 L012Q007 C030 C044D003 R018 R053 R033 3 R059 C021 L009 R019 48 33 C033 C049 1

C D002

C061 L016 L007 49 32L006 R073 1 R028Q024 LND002 C0022 1 Q014 C054 C03731R064 R070 C059 C056 R013R012L014 IC001 R002 For printed wiring boards C057 1 Q032 1 R008 • This board is six-layer print board. However, the pat- Q016 terns of layers two to five have not been included in L008 C051 D006 the diagram. B Q019 1 R010C050 1 R009 • Chip parts C048 Q030 Q031 R076 R00523R078 R079 R048R031 64 17 R006 Transistor Diode R003R004 R001391116C65421343C011 CN003 R046 R039 R020 R017BE1233452112A40 2 R038 C010 R029 There are few cases that the part printed on this diagram isn’t mounted in this model. 1-675-585- R037 R052 12 0912345678910 11 DC/DC CONVERTER DD-131 4-51 4-52, Q014 2SK1830-TE85L B+ SWITCH R006 ±0.5% 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 RT DTC5 0.5 CT DTC6 1.7 1.7 2.5DTC3 C007-IN(C)6 R029 0.01u C008 1.2 1.3 B 27k-IN(E)3 FB6 R034 5600 0.01u B 1.2±0.5% FB3 -IN(E)6 1.2 1.7 FB2 1.2OUT(A)6 R041 5600 ±0.5% 1k C009 1.2R040 -IN(E)2 6800p B -IN(A)6 2.5 0.8 DTC2 DTC7 2.5 1.1 C010DTC1-4 +IN(E)7 0.47u B 1.6 4.0 2012DTC1-3 -IN(E)7-2 1.7 DTC1-1 2.4 1.2 -IN(E)7-1 C012 0.5-IN(E)1 FB7 R049 2200p B 1.2 2200 FB1 XEB1-6 GND(0)1 GND5.6.7 0.3 RB1 RB7 0.5 6.4 OUT1-4 OUT7 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 4.554123R026 R031 220k 47k

Ver 1.1 1999.10 DSC-F505

12345678910 11 12 13 14 15 16 17 18 19 20

A DD-131 BOARD DC/DC CONVERTER(DD BLOCK)

-REF.NO.:2000 SERIES-

XX MARK : NO MOUNT NO MARK : STILL PB mode S : STILL mode B P : PB mode

838AN-1319 Q011 T003R036 CPH3206-TL 0.218k DC/DC CONVERTER C037 2.2u ±0.5% SWITCHINGB182012 R037 4.0 68k27±0.5% C038 2.2u R03836B

C R016 33k D001 201247k ±0.5% MA4ZD03001S0 R079

4 5 -14.9 3300 R012 R020 D006 33k 47k MA4ZD03001S0C026 C041 Q032 ±0.5% ±0.5% R039 C025 C0281u 1u 2SD2216J-QR(K8).SO10k R076 2.2u -14.3B 2.2u BB B+ SWITCH CN003 40P±0.5% R048 0 3216 B D004 3216XX 2012 3216 MA4ZD03001S0 R078 1 GND -14.9 47k R013 R046 Q009 DC/DC 838DN-1367R021 R032 R077 2 GND 22k 27k 010k C015 CPH3106-PM-TL T001 CONVERTER 100k ±0.5% ±0.5% 3300p B SWITCHING 3 BL_UNREGC011 R052 Q033 12.8 R001 2200p 27k 1 8D C044 L016 2SB1462J-QR(K8).SO 4 BL_UNREG 150k B 5.3 2.2u B 100uH B+ SWITCH ±0.5% 5 BAT_SIGC013 2012R055 4.027R017 120p 820 13.5 13.5 6 HI_UNREG 27k CH036L013 Q030 C016 100uH UN9210J-(K8).SO 7 XSTB_FULL 1.6 0.2 2.2u B+ SWITCH 8 EVER 3.5V 16 15 14 13 12 11 10987654321B45-14.9 3216 D005 C045 Q025 L012 C054 C056 9 STB_CHARGE MA4ZD03001S0 4.7u -14.9 R003 DC/DC 1u BQ010 T002 UN9213J-(K8).SO 100uH 1u Q031 10 PANEL+13.5V 100k 1 C017 CPH3106-PM-TL CONVERTER 3216 25V B EMERGENCY 2.6 B 4.8 UN9110J-(K8).SO3300p 2012C051 C059SWITCHING DETECT 4.7u B+ SWITCH 11 SYS_DD_ON

B

R004 C004 838AN-1353 C040 1u R071 L009 25V 12 PANEL+4.9VE 15k 0.001u S2.3/P0 S5.0/ 1 8 1u B 27k 4.7uH B2012 B 3.2±0.5% B 4.9Vcc(0)5.6.7 6.2 P6.3 D007 2012 13 LCD_DD_ON-IN(C)5 MA4ZD03001S0 S1.2/P0 5.0 R05627S1.1/OUT6 14 PANEL+6.5V-IN(E)5 R008 680 P0R005 15k 27k S1.4/P0 OUT5 4.6 R072 L015 47uH 15 A+4.9VFB5 4.0036 ±0.5% 18kR010 1.2 OUT4 5.5 16 A+4.9VFB4 C018 1.2 0 6800 C005 IC001 5.5 2.2uB4517 GND-IN(E)4 OUT3 3216 C039 Q023 L010 R007 2700p B 1.7 2.5 1u CPH5601-TL C058 Q016 47uH 18 GND 15k DTC4 B 4.7u ±0.5% XX 2.5 DC/DC CONVERTER Vss(0)4.5.6 Q005 SWITCH 4.9 CPH6301-TL C050 TO3216 B R009 6.2-IN(C)8 Vcc(0)3.4 2SB1462J-QR(K8).SO B+ SWITCH 1u 3216 19 CAM_DD_ON HI-70 BOARD 3.1 2.5 1.4 C020XX R062 L004 4.0 B (5/6) OUT2-2 C029 4.9 3216 20 M+5VF VREF IC001 B 220 22uH CN6010.001u 4.9R011 GND GND(0)2.3.4 R058 3.8 B 4.9 C047 21 PANEL_-15V THROUGH THEL011 47k 6.2 MB3827PFV-G-BND-ER 56003.8 C042

XX

OUT2-1 Q003,005,006 C046 B 1uH 3225 22 M+5V FP132 Vcc 4.5 C035 4.7u B XX R064

FLEXIBLE

DD ON 3.1 2.5 5.6 DRIVER 4.9 0Vss(0)1-2 2.2u 3216 B 470k 23 CAM-7.5VCTL1-4.7 B S0/ C052 CAM ON S3.1/P0 6.2 0.6 R067 CTL5 Vcc(0)1-2 4.0 0.2 3216 Q021 P4.9 1.5 47k 4.7u 24 D_2.35V (SEE PAGE LCD ON C001 3.1 3.2 R060 CPH5704-TL 1.0 B 0.022u B OUT1-1 10k R069 C061 R074 25 CAM+15V 4-48)CTL6 0 0.2 SWITCHING 10k C060 R070 0.47u 100k 3216 VG(0)1 8.3 0.1u 100k Q006 CS1-6BBQ017 26 D_2.35V C002 Q003 2SC1621-T1B3 S0/P4.9 0 R073 1.0 2SD2216J-QR(K8).SO 0.22uB0OUT1-2 2SB1462J-QR(K8).SO 4.0 B+ SWITCH 27 D_3.2VCSCP 10k Q007 R0652.0 0

G VB OUT1-3 2SB1462J-QR(K8).SO 33k

28 D_3.2V R002 C021 R059 R063 Q022 S3.1/P0 3.1 R066 R068 39k C003 XX B 3300 220 C030 L005 CPH5704-TL 33k 29 D_3.2V ±0.5% 0.1u 0.001uS3.8/ 22uH SWITCHING 10k B S4.4/ P4.0 B 4.0 30 D_3.2V P4.6 Q024Q004,007,008 5.0 XP4213-TXE 31 A_3.2V DRIVER SWITCH S5.5/ 32 A_3.2VC036 C043P6.2 2.2u 4.7u 33 GND 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 4.0 1.2 C053 R022 R061BBL006 10k 0.7 3216 3216 1uH 4.7u 34 GND 18k 0.5 B Q004 4.0 3216 35 GND 2SB1462J-QR(K8).SO 0.2 36 GND

H Q0082SC1621-T1B3

C006 37 GND 100p R033 C014 18k 100p C024 2.4 L003 38 GNDCH CH 3300p Q019 22uH C032 L007B CPH3403-TL 1uH4.7u 3225 C049 39 GND R057 SWITCHING S2.4/P0.1 B 4.7u 1800 3216 40 GND R018 R023 R053 22k 27k 18k S1.4/ 4.0 P0.6 Q012 R027 R044 R050 CPH5701-TL C027 R014 R030 12k 2.2u 27k 22k 15k 9100 B LND002

I ±0.5% ±0.5% 2012C022 MECA GNDR047

R043 2200p Q015 R024 15k B CPH5704-TL 0 15k 3.7 3.2 L014 R015 R028 ±0.5% ±0.5% 1uH R025 R051 3.2 47k R019 39k22k R045XX 27k 15k 4.0 3.2 ±0.5% L002R054 10uH L008 PS002 1uH220 1.4A Q013 3.2 CPH5701-TL C023 3.2 C048 C057 R035 R042 2.2u SWITCHING 0 3.2 4.7u 4.7u 39k 12k B C033

J ±0.5% ±0.5% 3216 Q020 4.7uB

PS003 CPH3403-TL 3216 1.4A SWITCHING 6.5 D003 RB521S-30-TE61 BT901 LF001 BATTERY PS0041.4A

TERMINAL

CN001 3P

K BATT UNREG 1 S BATT SIG 2

BATT GND 3 D002 MA3XD21001S0 LND001 MECA GND L001 100uH Note : Note : R075 0 PS001 3.9 IC002 2012 1.4A The components identified by Les composants identifiés par une

L 4.0 C034 DC/DC CONVERTER

4P CN002 C019 4.7u (STEP UP) mark ! or dotted line with mark marque ! sont critiques pour la 2.2u 3.9 B ST_GND1B3216 FLASH 3216 ! are critical for safety. sécurité. UNIT ST UNREG 2 IC002 (MC) STB_CHARGE 3 XC6372C351PR Replace only with part number Ne les remplacer que par une XSTB_FULL 4 09 specified. piéce portant le numéro spécifié.

DC/DC CONVERTER

4-53 4-54 DD-131, R9001 R9002 R9003000R014 100 R002 R9007 R900800

DSC-F505 Ver 1.1 1999.10

12345678910 11 12 13 14

A CONTROL SWITCH BLOCK(FK) T W R90110

RV001 R9012 • CONTROL SWITCH BLOCK(FK) is (ZOOM) D009 LND0020 replaced as a block. STATIC_GND

So that this PRINTED WIRING 1SS387-TPL3 BOARD is omitted. D006

TLYU1008(T05,SOY) (FLASH LAMP) CN002 18P R003 330

B 30P CN001 3

REG_GND14REG_GND REG_GND25ZOOM_SW_AD36SYS_V SYS_V47HSY D_3.2V58PANEL_COM

CPC

HSY69VG (FOR CHECK) STB_LED 7 10 HI_UNREG

C PANEL_COM 8 11 LANC_IN

REG_GND 9 12 LANC_OUT KEY_AD3 10 13 AU_OUT 11 14 RF7 TO VG 12 15 TXD HI-70 BOARD REG_GND 13 16 RXD (5/6) CN607 HI_UNREG 14 17 RESET REG_GND 15 18 VDD

D (SEE PAGE 4-47) LANC_IN 16 S004 S005 S007

REG_GND 17 DISPLAY LCD LCD R9010 LANC_OUT 18 BRIGHT(+) BRIGHT(-) 0 REG_GND 19 R007 R011 R013 2700 4700 6800 RF7 20 V_OUT 21 MENU (CONTROL BUTTON) S005 S007 TXD 22 S001 REG_GND 23

E RXD 24 UPAPSET

REG_GND 25 D004 RESET 26 LEFTDBRIGHT RD8.2UM-T1B2B3 KEY_AD1 27 D005 S006 VDD 28 C DOWN RD8.2UM-T1B2B3 LCD BACK LIGHT KEY_AD2 29 R010 R012 ON OFF 39k AV_JACK_IN 30 6800COMMON R008

F S003

R9009 0 S002 R004 1800 (FLASH) S003 R005 2700 PROGRAM AE R001 (Use for J001 guard.) 1k1608

G FB001R9004 • SIGNAL PATH J001 VIDEO SIGNAL AUDIO

A/V OUT D001 01ZA8.2(TPL3) (MONO) FB002 CHROMA Y Y/CHROMA SIGNAL R9006 R9005000FB003 REC

H PB

R9013 D003 01ZA8.2(TPL3) 09 STATIC_GND LND001

I CONTROL SWITCH BLOCK

FK 4-55 4-56,

Ver 1.1 1999.10 DSC-F505

4-3. WAVEFORMS

CD-236 BOARD HI-70 BOARD DD-131 BOARD

1 IC101 !£,@º 50 µsec/div 9 IC102 #∞ 50µsec/div 1 IC802 $¡ LCD 50µsec/div 9 IC902 7 !¶ IC301 1 A/V OUT 1 IC001 1 OUT7 0.5µsec/div 2 V/div 1V/div 0.5V/div 0.2V/div 6.5Vp-p 3.2Vp-p 4.8Vp-p 0.46Vp-p1.7Vp-p 150 µsec 50µsec/div H 20µsec/div 500kHz 0.8Vp-p150 µsec 2H 2H 2V/div 0.2V/div 2 IC101 !¢,!ª 50 µsec/div !º IC103 @¡, @™ 50nsec/div 2 IC802 @¢ !º IC901 #¶ !• IC603 $º 20MHz OUT 2 V/div 1V/div 4.5Vp-p 6.5Vp-p 3.2Vp-p 3.0Vp-p 150 µsec 12.2727 MHz 3.6Vp-p H 20µsec/div H 20µsec/div 20 MHz 20nsec/div 2V/div 1V/div 1V/div 3 IC101 1,2,3 50 µsec/div !¡ IC103 !ª 50µsec/div 3 IC802 @™ !¡ IC901 @§ !ª IC60215V/div 1V/div 4.5Vp-p 7.4Vp-p 4.1Vp-p 3.0Vp-p 150 µsec 3.2Vp-p H 20µsec/div 11.722 MHz 50nsec/div 32.768 kHz 20µsec/div 150 µsec 2V/div 2V/div 1V/div 4 IC101 4,5,6 50 µsec/div !™ IC103 @º, @£ 50µsec/div 4 IC802 @º !™ IC90125V/div 1V/div 4.5Vp-p 7.4Vp-p 4.8Vp-p 3.2Vp-p 20µsec/div 150 µsecHH20µsec/div 150 µsec 2V/div 2V/div 5 IC101 0 50 µsec/div !£ IC103 !§ 50nsec/div 5 IC802 !¢ !£ IC901 3 0.5 V/div 1V/div 1.0Vp-p 4.8Vp-p 4.8Vp-p 150 µsec 12.2727 MHz 3.4Vp-p H 20µsec/div H 20µsec/div 2V/div 2V/div 6 IC102 @∞ 20nsec/div !¢ IC103 2 – 0 50nsec/div 6 IC802 0 LCD !¢ IC901 4 1V/div 1V/div 0.18Vp-p 4.8Vp-p

H

24.54 MHz 3.4Vp-p 3.5Vp-p 20µsec/div H 20µsec/div0.1V/div 100 nsec 2V/div 7 IC102 #º 50nsec/div !∞ IC103 @§ 7 IC802 9 LCD 20µsec/div !∞ IC301 !ª A/V OUT 1V/div 0.1V/div 1.0Vp-p 0.36Vp-p 3.8Vp-p 0.36Vp-p12.2727 MHz 150 µsec 50µ Hsec/div H 20µsec/div0.5V/div 0.1V/div 8 IC102 #¢ 20nsec/div 8 IC802 8 !§ IC301 !™ A/V OUT 1V/div 0.46Vp-p 3.2Vp-p H 20µsec/div 2.0Vp-p 50 msec 0.2V/div H 20µsec/div 0.5V/div 4-57 4-58,

DSC-F505 Ver 1.1 1999.10

4-4. PRINTED PARTS LOCATION

CD-236 BOARD LD-98 BOARD HI-70 BOARD HI-70 BOARD DD-131 BOARD

C101 D-5 R116 E-1 C401 E-3 R430 B-4 (SIDE A) (SIDE B) C001 C-11 L006 C-3 R034 D-11 C102 D-5 R117 E-1 C402 E-4 R431 B-3 C002 C-11 L007 C-3 R035 D-10 C103 C-2 R118 E-1 C403 E-4 R432 C-3 BT601 B-10 C816 D-2 R314 F-5 R729 C-6 C608 A-4 C418 C-4C609 E-1 C419 C-4 C003 C-11 L008 B-1 R036 A-8C104 A-5 R119 D-2 C404 B-3 R433 E-3 C817 E-2 R606 G-9 R732 D-8 C004 B-11 L009 C-7 R037 A-8 C105 D-4 R120 D-2 C405 F-5 R434 E-4 C301 F-5 C901 A-5 R607 F-7 R733 E-8 C629 A-4 C420 E-3 C005 B-11 L010 B-5 R038 A-9 C106 A-2 R121 D-2 C406 C-2 R435 E-4 C302 F-2 C902 C-5 R608 B-1 R801 D-3 C630 A-5 C421 C-4C738 B-5 C422 C-5 C006 D-11 L011 C-4 R039 A-10C107 B-4 R122 E-2 C407 C-1 R436 C-2 C303 D-1 C903 A-3 R609 B-9 R804 C-3 C007 A-10 L012 C-6 R040 D-10 C108 A-2 R123 E-2 C408 C-1 R437 A-3 C304 D-3 C904 C-5 R610 F-8 R805 C-3 C742 A-5 C423 B-3C812 A-9 C424 C-3 C008 D-10 L013 B-7 R041 D-10C109 C-2 R124 B-1 C409 C-2 R438 B-3 C306 F-2 C905 B-4 R611 F-8 R806 C-3 C813 A-9 C425 B-3 C009 D-10 L014 B-2 R042 D-10C110 D-4 C410 C-2 R439 F-4 C307 E-1 C906 A-3 R612 F-8 R812 D-1 C814 A-9 C426 C-2 C010 A-9 L015 C-6 R043 D-10C111 A-6 X101 D-8 C411 F-3 C308 E-2 C907 A-3 R613 B-10 R817 D-2 C815 A-10 C011 A-9 L016 B-5 R044 C-8C112 A-6 X102 D-5 C412 F-3 C309 E-3 C908 A-2 R614 B-9 R818 D-2 C012 D-10 R045 C-8 C113 C-5 C413 C-4 C310 D-1 C909 A-2 R615 B-9 R819 E-2 C915 A-10 CN401 A-4C916 A-9 CN402 D-2 C013 A-8 LF001 F-10 R046 A-9C114 B-6 C414 B-4 C311 E-3 C911 A-2 R616 B-9 R820 D-2 C115 E-4 C415 B-4 C312 E-3 C913 B-5 R617 B-8 R821 D-2 C919 A-8 C014 C-9 R047 D-10 C015 F-7 PS001 H-11 R048 B-8 C116 D-3 C416 B-4 C313 E-3 C917 A-5 R622 F-9 R822 C-3 C920 A-6 D401 C-3 C016 G-7 PS002 F-11 R049 D-9 C117 E-5 C417 C-4 C315 F-1 C918 A-5 R624 C-10 R823 C-3 D402 B-3CN604 A-7 C017 H-7 PS003 G-11 R050 D-9C118 E-4 C418 C-4 C316 E-1 C927 A-4 R625 F-9 R824 D-2 CN606 D-3 IC401 B-5 C018 H-6 PS004 F-10 R051 D-9C119 D-4 C419 C-4 C317 D-3 R626 D-10 R827 C-3 CN701 A-6 IC402 F-4 C019 H-2 R052 A-8C120 E-3 C420 E-3 C318 D-3 CN601 F-6 R627 D-8 R828 C-3 C020 G-6 Q001 H-8 R053 C-3 C121 E-4 C421 C-4 C605 F-7 CN602 F-3 R628 D-8 R905 A-2 IC403 E-4 C021 C-4 Q003 G-5 R054 C-2 C122 C-5 C422 C-5 C606 F-9 CN603 C-3 R630 E-9 R906 A-4 D606 E-1 IC404 B-2D608 E-2 IC405 B-4 C022 C-2 Q004 D-4 R055 F-7C123 A-4 C423 B-3 C607 F-9 CN605 G-10 R633 E-8 R907 A-2 C023 F-1 Q005 H-5 R056 H-7 C124 D-3 C424 C-3 C610 D-8 CN607 B-8 R634 E-8 R908 A-2 IC406 D-3 C125 E-4 C425 B-3 C611 E-10 CN702 G-9 R635 F-8 R909 A-2 FB605 A-8 IC407 B-3 C024 H-4 Q006 H-5 R057 H-4 C024 H-4 Q007 C-4 R058 G-6 C126 E-3 C426 C-4 C612 D-8 CN901 B-6 R636 E-8 R910 A-4 IC601 A-5 L401 F-3 C025 H-8 Q008 D-3 R059 C-4C127 E-3 C613 D-8 R637 C-10 R912 B-4 C026 H-8 Q009 G-7 R060 H-5 C128 A-4 CN401 A-4 C614 D-8 D602 G-10 R638 B-10 R913 A-2 IC605 A-4 L402 E-3 C129 D-2 CN402 D-2 C615 D-10 D604 B-9 R639 B-10 R914 A-3 IC606 A-5 L403 E-1 C027 I-3 Q010 H-6 R061 D-4 IC607 E-1 L404 B-3 C028 I-8 Q011 H-8 R062 H-5C130 E-2 C616 D-10 D607 B-1 R641 F-8 R915 A-2 C029 H-5 Q012 H-3 R063 D-4 C131 E-2 D401 C-3 C617 E-8 D902 B-5 R642 E-8 R916 A-2 L601 A-4 Q401 C-2 C030 C-4 Q013 D-1 R064 B-4C132 A-3 D402 B-3 C618 E-8 D903 A-2 R643 D-10 R918 A-2 C133 E-9 C619 E-8 D904 A-5 R644 F-8 R920 B-4 Q402 E-5 C032 I-3 Q014 C-11 R065 B-4 C033 C-1 Q015 D-1 R066 B-4 C134 D-2 IC401 B-5 C620 F-10 R645 E-8 R921 A-2 Q604 F-1 Q403 E-4 C034 H-2 Q016 B-4 R067 B-4 C135 B-3 IC402 F-4 C621 F-10 FB606 A-8 R646 F-8 R922 A-2 Q609 E-2 Q404 C-5Q611 G-3 Q405 F-3 C035 G-5 Q017 B-4 R068 B-4C136 B-4 IC403 E-4 C622 E-8 FB607 A-8 R647 E-8 R924 B-4 C036 G-3 Q019 B-3 R069 C-5 C137 C-4 IC404 B-2 C623 E-8 FB701 C-5 R649 D-3 R926 A-2 Q612 G-2 Q406 B-3 C037 C-8 Q020 C-1 R070 C-5 C138 B-3 IC405 B-4 C624 F-9 FB901 A-3 R650 F-8 R928 B-3 Q903 A-10 C139 A-4 IC406 D-3 C627 B-8 R651 E-8 R929 A-1 Q904 A-10 R402 F-4 C038 C-8 Q021 G-4 R071 I-4 Q905 A-9 R403 E-5 C039 H-5 Q022 G-3 R072 I-4C140 A-4 IC407 B-3 C631 E-8 IC301 E-2 R653 E-10 R930 A-1 C040 H-6 Q023 D-5 R073 C-5 C632 E-8 IC602 F-10 R654 E-8 R938 A-1 Q906 A-10 R404 E-5 C041 D-7 Q024 C-6 R074 C-5 CN101 C-1 L401 F-3 C633 E-9 IC603 D-9 R656 E-8 R939 A-1 R405 E-5 L402 E-3 C701 D-5 IC702 D-6 R657 B-9 R941 A-5 R604 E-1 R406 C-3 C042 G-4 Q025 I-4 R075 F-9 R605 F-1 R407 B-5 C043 F-3 Q030 B-7 R076 B-8FB101 A-6 L403 E-1 C702 B-7 IC801 B-2 R658 B-9 R942 A-5 R618 C-1 R408 F-5 C044 C-7 Q031 B-7 R077 B-6FB103 D-5 L404 B-3 C703 D-6 IC802 D-2 R659 B-9 R943 A-5 C045 G-6 Q032 B-7 R078 B-6 FB104 C-6 C704 D-6 IC803 D-3 R660 B-9 R944 A-5 R619 D-1 R409 B-5 C046 C-4 Q033 B-6 R079 B-7 FB105 C-5 Q401 C-2 C711 C-5 IC901 B-3 R661 F-10 R967 B-6 R620 D-1 R410 C-1 C047 D-6 Q057 H-4 FB106 D-2 Q402 E-5 C712 D-5 IC902 A-1 R662 F-10 R968 B-6 R621 E-1 R411 B-5 FB107 B-2 Q403 E-4 C713 C-6 R663 G-10 R969 B-6 R623 F-1 R412 C-2 C048 B-2 T001 G-6 C049 C-2 R001 B-11 T002 I-6 FB108 B-1 Q404 C-5 C714 C-6 L301 F-5 R670 E-10 R978 A-4 R648 D-1 R413 C-1R667 E-2 R414 C-2 C050 B-5 R002 B-11 T003 I-7FB109 A-5 Q405 F-3 C715 C-6 L302 F-3 R671 B-10 R979 A-4 C051 B-8 R003 B-11 FB110 A-5 Q406 B-3 C716 C-6 L303 D-4 R672 D-8 R980 A-4 R668 D-2 R415 B-2 C052 C-4 R004 B-11 FB111 A-5 C717 C-6 L701 B-6 R673 B-9 R981 A-2 R669 E-2 R416 C-2 C053 C-3 R005 B-11 R402 F-4 C721 C-6 L704 E-7 R674 C-10 R982 A-4 R675 A-5 R417 E-4 C054 C-7 R006 B-11 IC101 B-9 R403 E-5 C723 D-7 L706 C-8 R676 B-10 X602 F-10 R679 F-1 R418 B-4R726 B-5 R419 B-4 C056 B-8 R007 B-11IC102 B-5 R404 E-5 C724 C-7 L801 D-1 R677 B-10 C057 B-2 R008 B-11 IC103 D-3 R405 E-5 C725 E-6 L802 C-1 R678 B-9 R727 A-5 R420 B-4 IC104 A-4 R406 C-3 C726 E-7 L901 C-5 R680 C-8 R932 A-9 R421 B-4 C058 B-5 R009 B-11 C059 B-6 R010 B-11 R407 B-5 C727 C-7 L902 B-5 R681 F-8 R933 A-10 R422 B-4 L101 B-2 R408 F-5 C728 C-7 L903 A-5 R682 C-8 R934 A-9 R423 B-4 C060 C-5 R011 B-11 R935 A-10 R424 B-4 C061 C-5 R012 B-11L102 A-3 R409 B-5 C729 D-7 L905 A-3 R701 D-5 R013 C-11 L103 E-9 R410 C-1 C730 E-7 R702 D-5 R425 B-4X601 D-2 R426 C-3 CN001 H-9 R014 D-11R411 B-5 C731 D-7 Q302 F-2 R703 E-6 R427 C-3 CN002 I-11 R015 D-11Q101 D-4 R412 C-2 C732 D-7 Q303 F-3 R704 D-7 CN003 A-7 R016 A-11 Q102 A-2 R413 B-1 C733 E-5 Q304 E-4 R705 C-6 LD-98 R428 B-4 R017 A-11 Q103 E-5 R414 C-1 C734 E-6 Q305 E-5 R706 D-7 R429 B-4 R415 B-2 C735 C-5 Q603 F-8 R707 C-6 C401 E-3 R430 B-4 D001 I-8 R018 C-8 D002 C-2 R019 C-8 R101 D-5 R416 C-2 C739 C-5 Q605 B-1 R708 D-5 C402 E-4 R431 B-3 R102 A-2 R417 E-4 C740 B-7 Q607 F-9 R709 C-6 C403 E-4 R432 C-3 D003 C-1 R020 A-11 C404 B-3 R433 E-3 D004 D-6 R021 A-11R103 A-2 R418 B-4 C741 E-6 Q608 F-9 R711 B-6 C405 E-5 R434 E-4 D005 C-6 R022 C-11R104 A-5 R419 B-4 C743 C-7 Q610 F-9 R712 C-7 R105 A-5 R420 A-4 C744 E-6 Q701 B-7 R713 B-7 C406 C-2 R435 E-4 D006 B-8 R023 C-8 C407 C-1 R436 C-2 D007 I-5 R024 C-9R106 C-6 R421 B-4 C745 C-7 Q702 C-7 R714 D-5 R025 C-8 R108 C-6 R422 B-4 C801 B-1 Q704 C-8 R715 D-7 C408 C-1 R437 A-3 IC001 B-11 R026 B-6 R109 E-5 R423 B-4 C802 B-1 Q705 C-5 R717 E-5 C409 C-2 R438 B-3C410 C-2 R439 F-4 IC002 G-2 R027 C-8R110 C-6 R424 B-4 C803 D-2 Q706 B-7 R718 E-7 R028 C-8 R111 C-5 R425 B-4 C804 D-2 R719 C-5 C411 F-3 L001 D-1 R029 A-10 R112 D-4 R426 C-3 C805 D-1 R303 F-3 R720 C-6 C412 F-3 L002 G-1 R030 C11 R113 B-4 R427 C-3 C806 C-3 R304 F-3 R721 B-8 C413 C-4 L003 I-3 R031 B-5 R114 D-1 R428 B-4 C807 D-1 R305 E-2 R723 E-6 C414 B-4C415 B-4 L004 G-5 R032 A-10R115 E-1 R429 B-4 C808 D-3 R307 D-1 R724 E-6 L005 H-3 R033 D-10 C810 C-1 R312 F-2 R725 C-6 C416 B-4 C811 C-1 R313 F-2 R728 C-6 C417 C-4 4-59 4-60E,

DSC-F505 SECTION 5 ADJUSTMENTS

1. Before starting adjustment

EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair) PC PC (Machine after a board is replaced) Save the EVR data Download the saved to a personal computer. data to a machine. Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it. (Former board) (New board) Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the data from the same model of the same destination, and download it. (Machine to be repaired) PC (Machine to be repaired) Download the data. Save the data. (The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 5-1, 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by r in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment Adjustment Section Initialization of B, D, Initialization of D page datarrE, F page data Initialization of B, E, F, 7 page datarrVideo sync level adj. rrrrrVideo Video burst level adj. rrrrrHALL adj. rrrrFlange back adj. rrrrrFNo. standard data inputrrrrrMechanical shutter adj. rrrrrAGC standard gain and max gain adj. rrrrrLight level adj and ND shutter checkrrrrrrCamera Auto white balance standard data inputrrrrrAuto white balance ND filter compensation adj. rrrrrAuto white balance adj. rrrrrColor reproduction adj. rrrrrStrobe white balance adj. rrrrrrrCCD (black and white) defect compensationrrrrLCD initial data inputrrVCO adj. rrrrDrange adj. rrrrBright adj. rrrrLCD Contrast adj. rrrrColor adj. rrrrV-COM level adj. rrrrV-COM adj. rrrrrWhite balance adj. rrrrrrSystem control Battery end adj. r r Table. 5-1-1. 5-2 Lens device Strobe unit LCD block LCD901 (LCD panel) LCD block ND901 Back light unit CD-236 board IC101 (CCD imager) CD-236 board IC103 (S/H, AGC, A/D) LD-98 board IC407 (EVR) HI-70 board IC301 (VIDEO AMP) HI-70 board IC802 (RGB decoder) HI-70 board IC901 (Timing generator) HI-70 board IC801 (EVR) SY-56 board (COMPLETE) CD-236 board (COMPLETE) PS-427 board (COMPLETE) HI-70 board (COMPLETE) HI-70 board IC607 EEPROM, 5-1. ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check J-1 Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check ND filter 1.0 J-6080-808-A White balance check J-2 ND filter 0.4 J-6080-806-A White balance check ND filter 0.1 J-6080-807-A White balance check J-3 Pattern box PTB-450 J-6082-200-A J-4 Color chart for pattern box J-6020-250-A Adjustment remote commander (RM-95 upgraded). J-5 J-6082-053-B (Note 1) J-6 Siemens star chart J-6080-875-A For checking the flange back J-7 Clear chart for pattern box J-6080-621-A For connecting the adjustment remote commander J-8 CPC-9 jig (Note 2) J-6082-393-C For adjusting the LCD block J-9 Mini pattern box J-6082-353-B For adjusting the flange back For extension between the CD-236 board (CN101) and J-10 Extension cable (39P, 0.3mm) J-6082-448-A the PS-427 board (CN251) J-11 Personal computer with Windows95/98 installed For checking the recorded picture Picture management software J-12 Picture Gear Ver.3.2 Lite For checking the recorded picture For extension between the SY-56 board (CN455, 456) J-13 Extension cable (33, 39P, 0.3mm) J-6082-447-A and the HI-70 board (CN602, 603) J-14 Back ground paper J-2501-130-A For adjusting the strobe Note 1: If the micro processor IC in the adjustment remote commander is Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, not the new micro processor (UPD7503G-C56-12), The pages because it cannot operate the adjustment remote commander. cannot be switched. In this case, replace with the new micro processor (8-759-148-35). J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 J-10 J-11 J-12 J-13 Below 3 cm J-14 Minipattern box Camera Table Regulated power supply Output voltage: Specified voltage ± 0.01Vdc Output current: more than 3.5A Red (+) Black (–) Yellow (SENS +) White (SENS –) Need not connected Black (GND) Fig. 5-1-1. 5-3, 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-5. 2) Connect the Adjustment remote commander to control switch block (FK) CN002 via CPC-9 jig (J-6082-393-C, Note3). (See Fig. 5-1-4.) To operate the adjustment remote commander, connect the power supply terminal of CPC-9 jig to the DC power About 90 cm supply (6.0 to 7.2Vdc). Note 3: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 4: Setting the “Forced Power ON Mode (Forced STILL Mode)” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. Note 5: Setting the “Forced Power ON Mode (Forced PLAY Mode)” 1) Select page: 0, address: 01, and set data: 01. Front of the lens 2) Select page: D, address: 10, set data: 02, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the power (PLAY mode) to be turned on. After completing adjustments, be sure to exit the Fig.5-1-2. “Forced Power ON Mode”. Note 6: Exiting the “Forced Power ON Mode” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00. Capacitor Short jig (See page 5) 1-1-3. Discharging of the strobe power supply The capacitor which is used as power supply of strobe is charged with 200V to 300V voltage. Discharge this voltage before starting adjustments in order to protect service engineers from electric shock R: 1kΩ 1W during adjustment. (Parts code : 1-215-869-11) Discharge procedure Flash unit (MC) 1. Press the FLASH button (Control switch block (FK) ) and turn off the FLASH LED (Control switch block (FK) ). 2. Fabricate the short jig as shown in Fig. 5-1-3 locally by yourself. Fig.5-1-3. Connect the short jig to the positive (+) and negative (-) terminal of the flash voltage charge capacitor. Allow ten seconds to discharge the voltage. Slide the Release knob in the direction of arrow A. Control switch block (FK) To open the Battery lid. (CN002) 18

A

CPC-9 jig (18p flexible board) Two claws CPC cover Release knob Note : Don't use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit Fig.5-1-4. 5-4,

Ver 1.1 1999.10 VIDEO

Terminated at 75Ω (Yellow) Vector scope Color monitor

AUDIO

Harness (SP-163) To HI-70 board, CN702 Inverter transformer unit (White) AV out J001 Control switch block (FK) CN002 18 Harness (HB-50) To HI-70 board, CN605 CN607 CN901 Memory stick CN603 DC power supply CN601 (6.0 to 7.2Vdc) CN602 CN605 12 1 18 1 HI-70 board 12 pin 18 pin CN702 CN003 CN001 CPC-9 jig (*Note) DD-131 board (J-6082-393-C) Adjusting remote commander AC power adaptor Battery holder assembly *Note : The old CPC-9 jig (Parts code : J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Fig.5-1-5. 5-5, 1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments. 1. WHITE BALANCE (Control switch block (CF) ) ... AUTO 2. FLASH LEVEL (Menu display) ...NORMAL 3. EXPOSURE (Menu display) ... 0EV 4. EFFECT (Menu display) ...OFF 5. DEMO MODE (Menu display) ...OFF 6. VIDEO OUT (Menu display) ... NTSC 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame

H

C C=D D CRT picture frame

V

A B A=BBAFig. b (monitor TV picture) Fig. a Enlargement ( V ideoteoutputwarminalveform ) Difference in level Adjust the camera zoom and direction to obtain the output waveform shown in Fig. aBAand the monitor TV display shown in Fig. b. Fig.5-1-6. 3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust White the picture frame as shown in Fig. 5-1-6. (Color reproduction 841mm adjustment frame) 2) Clear chart (Color reproduction adjustment frame) Black Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations during this time.) 1189mm 3) Flange back adjustment chart Make the chart shown in Fig. 5-1-7. using A0 size (1189mm × 841mm) black and white vellum paper. Fig. 5-1-7. Note: Use matte vellum paper bigger than A0, and make sure the edges of the black and white paper joined together are not rough. 5-6 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15mm thickness. woody board A (2) woody board B (2) woody board C (1) 530 mm 500 mm 1000 mm 1026 mm 1026 mm 1000 mm 1030 mm 1000 mm Fig.5-1-8. 2) Apply black mat paint to one side of woody board A and B. 3) Attach background paper (J-2501-130-A) to woody board C. 4) Assemble so that the back sides of woody board A, B and C and the background paper side are internal. (Fig 5-1-9) woody board B woody board A woody board A woody board B woody board C Fig.5-1-9. 5-7, 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA 3. D Page Table 1-2-1. INITIALIZATION OF D PAGE DATA Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the D Page 1. Initializing the D Page Data Data”.) Note: If the D page data has been initialized, the following adjustments Fixed data-2 : Modified data. (Refer to “2. Modification of D Page need to be performed again. Data”.) 1) Modification of D page data 2) LCD system adjustments RemarkAddress Initial value 3) Battery end adjustments NTSC PAL 00 to 0F Adjusting page D 10 00 00 Test mode Adjusting Address 10 to EF 11 Fixed data-1 Initializing Method: 12 (Initialized data) 1) Select page: 0, address: 01, and set data: 01. 13 2) Select page: 2, address: 03, and set data: 00. 14 3) Select page: 2, address: 00, and set data: 2D. 15 Fixed data-2 4) Select page: 2, address: 01, set data: 2D, and press the PAUSE 16 Fixed data-1 button of the adjustment remote commander. 5) Select page: 2, address: 02, and check that the data changes to 17 (Initialized data) “01”. 18 6) Perform “Modification of D Page Data”. 19 1A 2. Modification of D Page Data 1B If the D page data has been initialized, change the data of the “Fixed 1C data-2” address shown in the following table by manual input. 1D Modifying Method: 1E 1) Before changing the data, select page: 0, address: 01, and set 1F data: 01. 20 2) New data for changing are not shown in the tables because 21 they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may 23 not operate. 24 3) When changing the data, press the PAUSE button of the 25 adjustment remote commander each time when setting new 26 data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. 27 If not, change the data to the initial value. 28 Processing after Completing Modification of D Page data 2A 1) Select page: 2, address: 00, and set data: 29. 2B 2) Select page: 2, address: 01, and set data: 29, and press the 2C PAUSE button of the adjustment remote commander. 2D 2E 2F 30 80 80 Battery end adj. 31 88 88 32 AD AD 33 C2 C2 34 CD CD 35 Fixed data-1 36 (Initialized data) 38 Fixed data-2 39 (Modified data, copy the data built in 3A the same model.) 3B 3C Fixed data-1 3D Fixed data-2 3E (Modified data, copy the data built in 3F the same model.) 5-8, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL 42 Fixed data-1 79 Fixed data-1 43 (Initialized data) 7A (Initialized data) 44 7B 45 Fixed data-2 7C 46 Fixed data-1 7D 47 (Initialized data) 7E 48 7F 49 80 BC BC Bright adj. (LCD) 4A 05 05 Battery end adj. 81 80 80 Color adj. (LCD) 4B Fixed data-1 82 B9 B9 White balance adj. (LCD) 4C (Initialized data) 83 B7 B7 4D 84 BE BE Contrast adj. (LCD) 4E 85 C8 C8 D range adj. (LCD) 4F 86 7C 7C V-COM level adj. (LCD) 50 87 50 50 NTSC: VCO adj. (LCD) 51 88 74 74 V-COM adj. (LCD) 52 89 Fixed data-1 53 8A (Initialized data) 54 8B 55 8C 56 8D 50 50 PAL: VCO adj. (LCD) 57 8E Fixed data-1 58 8F (Initialized data) 59 90 5A 91 5B 92 5C 93 5D 94 5E 95 5F 96 60 97 61 98 62 99 63 9A 64 9B 65 9C 66 9D 67 9E 68 9F 69 A0 Fixed data-2 6A A1 (Modified data, copy the data built in 6B A2 the same model.) 6C A3 6D A4 Fixed data-1 6E A5 (Initialized data) 6F A6 70 A7 71 A8 72 A9 73 AA 74 AB 75 AC 76 AD 77 AE 78 AF 5-9, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL B0 Fixed data-1 E2 Fixed data-2 B1 (Initialized data) E3 (Modified data, copy the data built in B2 E4 the same model.) B3 E5 B4 E6 B5 E7 B6 E8 Fixed data-1 B7 E9 (Initialized data) B8 EA B9 EB BA EC BB ED BC EE BD EF BE Table. 5-1-2.

BF

C0 Fixed data-2 (Modified data, copy the data built in the same model.) C1 Fixed data-1 C2 (Initialized data) C3 Fixed data-2 (Modified data, copy the data built in the same model.) C4 Fixed data-1 C5 (Initialized data) C6 C7 C8 C9

CA CB CC CD CE CF

D0 D1 D2 D3 D4 Fixed data-2 D5 (Modified data, copy the data built in the same model.) D6 Fixed data-1 D7 (Initialized data) D8 D9

DA DB DC DD DE DF

E0 Fixed data-2 E1 (Modified data, copy the data built in the same model.) 5-10, 1-2-2. Initializing the B, E, F, 7 Page Data 3. F Page table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , 1. Initializing the B, E, F, 7 Page Data 7 Page Data”.) Note: If the B, E, F Page data has been initialized, “Modification of B, E, Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , F, 7 Page Data” and following adjustments need to be performed 7 Page Data”.) again. 1) Modification of B, E, F, 7 page data Remark 2) Video system adjustments Address Initial value 3) Camera system adjustments NTSC PAL 00 to 0F Adjusting page F 10 Fixed data-1 Adjusting Address 10 to FF 11 (Initialized data) Adjusting page E 12 Adjusting Address 00 to FF 13 Adjusting page B 14 1C 1C Flange back adj. 15 94 94 Adjusting Address 00 to FF 16 26 26 Adjusting page 7 17 EC EC Adjusting Address 00 to AF 18 13 13 19 B9 B9 Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 1A 00 00 2) Select page: 6, address: 00, and set data: 2D. 1B 00 00 3) Select page: 6, address: 01, set data: 2D, and press the PAUSE 1C 00 00 button of the adjustment remote commander. 1D 00 00 4) Select page: 6, address: 02, and check that the data changes to 1E 46 46 “01”. 1F 00 00 5) Perform “Modification of B, E, F, 7 Page Data”. 20 20 20 2. Modification of B, E, F, 7 Page Data 21 20 20 If the B, E, F, 7 Page data has been initialized, change the data of 22 23 23 the “Fixed data-2” address shown in the following tables by manual 23 44 44 input. 24 0A 0A 25 00 00 Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set 26 A8 A8 Light level adj. data: 01. 27 A0 A0 AGC Standard Gain and Max Gain adj. 2) New data for changing are not shown in the tables because 28 85 85 Light level adj. they are different in destination. When changing the data, copy 29 5C 5C F No. standard data input the data built in the same model. 2A 4E 4E Note: If copy the data built in the different model, the camcorder may not operate. 2B 49 49 3) When changing the data, press the PAUSE button of the 2C 45 45 adjustment remote commander each time when setting new 2D Fixed data-1 data to write the data in the non-volatile memory. 2E 7A 7A HALL adj. 4) Check that the data of adjustment addresses is the initial value. 2F 77 77 If not, change the data to the initial value. 30 Fixed data-1 Processing after Completing Modification of B, E, F, 7 Page data 31 (Initialized data) 1) Select page: 2, address: 00, and set data: 29. 32 2) Select page: 2, address: 01, and set data: 29, and press the 33 PAUSE button of the adjustment remote commander. 34 14 14 HALL adj. 35 78 78 36 Fixed data-1 37 (Initialized data) 3A 2F 2F AWB standard data input 3B 37 37 3C 40 40 3D D0 D0 3E Fixed data-1 3F B5 B5 Auto white balance adj. 40 43 43 41 03 03 Color reproduction adj. (without ND filter) 5-11, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL 42 E9 E9 Color reproduction adj. 79 33 33 Mechanical shutter adj. 43 63 63 (without ND filter) 7A 33 33 44 83 83 7B 33 33 45 D5 D5 7C 33 33 46 FE FE 7D 33 33 47 73 73 7E 33 33 48 45 45 7F 33 33 49 Fixed data-1 80 00 00 Auto white balance adj. 4A (Initialized data) 81 Fixed data-1 4B 82 (Initialized data) 4C 83 4D 27 27 Strobe white balance adj. 84 4E 77 77 85 4F 00 00 Auto white balance ND filter 86 50 00 00 compensation adj. 87 51 00 00 Color reproduction adj. 88 52 00 00 (with ND filter) 89 53 00 00 8A 54 00 00 8B 55 00 00 8C 56 00 00 8D 57 00 00 8E 58 00 00 8F 59 00 00 AWB standard data input 90 5A 14 14 Mechanical shutter adj. 91 5B Fixed data-1 (Initialized data) 92 5C 00 00 Color reproduction adj. 93 5D 00 00 (without ND filter) 94 5E 00 00 95 5F 00 00 96 60 00 00 Color reproduction adj. 97 61 00 00 (with ND filter) 98 62 00 00 99 63 00 00 9A 64 Fixed data-1 9B 65 61 61 Video sync level adj. 9C 66 61 61 Video burst level adj. 9D 67 Fixed data-1 9E 68 0B 0B Strobe white balance adj. 9F 69 3B 3B A0 6A 00 00 A1 6B 2B 2B A2 6C 07 07 Mechanical shutter adj. A3 6D D0 D0 A4 6E 07 07 A5 6F D0 D0 A6 70 07 07 A7 71 D0 D0 A8 72 07 07 A9 73 D0 D0 AA 74 07 07 AB 75 D0 D0 AC 76 33 33 AD 77 33 33 AE 78 33 33 AF 5-12, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL B0 Fixed data-1 E7 Fixed data-1 B1 (Initialized data) E8 (Initialized data) B2 E9 B3 EA B4 EB B5 EC B6 ED B7 EE B8 EF B9 Fixed data-2 F0 BA Fixed data-1 F1 BB (Initialized data) F2 BC F3 BD F4 BE F5 BF F6 C0 F7 C1 F8 C2 F9 C3 FA C4 FB C5 FC C6 FD C7 FE C8 FF C9 Table. 5-1-3.

CA CB CC CD CE CF

D0 D1 D2 D3 D4 D5 D6 D7 D8 D9

DA DB DC DD DE DF

E0 E1 E2 E3 E4 E5 E6 5-13, 4. E Page Table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , RemarkInitial value 7 Page Data”.) Address Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , NTSC PAL 7 Page Data”.) 33 Fixed data-1 34 (Initialized data) Remark Address Initial value 35 NTSC PAL 36 00 Fixed data-1 37 01 (Initialized data) 38 02 39 03 3A 04 3B 05 3C 06 3D 07 3E 08 3F 09 40 0A 41 0B 42 0C 43 0D 44 0E 45 0F 46 10 47 11 48 12 49 13 4A 14 4B 15 4C 16 4D 17 4E 18 4F 40 40 AGC standard gain and max gain adj. 19 50 Fixed data-1 1A 51 (Initialized data) 1B 52 1C 53 1D 54 1E 55 1F 56 20 57 21 58 22 59 23 5A 24 5B 25 5C 26 5D 27 5E 28 5F 29 60 2A 61 2B 62 2C 63 2D 64 2E 65 2F 66 30 67 31 68 32 69 5-14, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL 6A Fixed data-1 A1 Fixed data-1 6B (Initialized data) A2 (Initialized data) 6C A3 6D A4 6E A5 6F Fixed data-2 A6 70 Fixed data-1 (Initialized data) A7 71 Fixed data-2 A8 72 Fixed data-1 A9 73 (Initialized data) AA 74 AB 75 AC 76 AD 77 AE 78 AF 79 B0 7A B1 7B B2 7C B3 7D B4 7E B5 7F B6 80 B7 81 B8 82 B9 83 BA 84 BB 85 BC 86 BD 87 BE 88 BF 89 C0 8A C1 8B C2 8C C3 8D C4 8E C5 8F Fixed data-2 C6 90 Fixed data-1 C7 91 (Initialized data) C8 92 C9 93 CA 94 CB 95 CC 96 CD 97 CE 98 CF 99 D0 9A D1 9B D2 9C D3 9D D4 9E D5 9F D6 A0 D7 5-15, 5. B Page Table Remark Initial value Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F ,Address 7 Page Data”.) NTSC PAL Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , D8 Fixed data-1 7 Page Data”.) D9 (Initialized data) Remark DA Address Initial value DB NTSC PAL DC 00 Fixed data-2 DD 01 Fixed data-1 DE 02 (Initialized data) DF 03 E0 04 E1 05 E2 06 E3 07 E4 08 E5 09 E6 0A E7 0B E8 0C E9 0D EA 0E EB 0F EC 10 ED 11 EE 12 EF 13 F0 14 F1 15 F2 16 F3 17 F4 18 F5 19 F6 1A F7 1B F8 1C F9 1D FA 1E FB 1F FC 20 FD 21 FE 22 FF 23 Table. 5-1-4. 24 2A 2B 2C 2D 2E 2F 5-16, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL 33 Fixed data-1 6A Fixed data-1 34 (Initialized data) 6B (Initialized data) 35 6C 36 6D 37 6E 38 6F 39 70 3A 71 3B 72 3C 73 3D 74 3E 75 3F 76 40 77 41 78 42 79 43 7A 44 7B 45 7C 46 7D 47 7E 48 7F 49 80 4A 81 4B 82 4C 83 4D 84 4E 85 4F 86 50 87 51 88 52 89 53 8A 54 8B 55 8C 56 8D 57 8E 58 8F 59 90 5A 91 5B 92 5C 93 5D 94 5E 95 5F 96 60 97 61 98 62 99 63 9A 64 9B 65 9C 66 9D 67 9E 68 9F 69 A0 5-17, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL A1 Fixed data-1 D8 Fixed data-1 A2 (Initialized data) D9 (Initialized data) A3 DA A4 DB A5 DC A6 DD A7 DE A8 DF A9 E0 AA E1 AB E2 AC E3 AD E4 AE E5 AF E6 B0 E7 B1 E8 B2 E9 B3 EA B4 EB B5 EC B6 ED B7 EE B8 EF B9 F0 BA F1 BB F2 BC F3 BD F4 BE F5 BF F6 C0 F7 C1 F8 C2 F9 C3 FA C4 FB C5 FC C6 FD C7 FE C8 FF C9 Table. 5-1-5.

CA CB CC CD CE CF

D0 D1 D2 D3 D4 D5 D6 D7 5-18, 6. 7 Page Table Note: Fixed data-1 : Initialized data. (Refer to “1. Initializing the B, E, F , Remark Address Initial value7 Page Data”.) Fixed data-2 : Modified data. (Refer to “2. Modification of B, E, F , NTSC PAL 7 Page Data”.) 33 Fixed data-1 34 (Initialized data) Remark Address Initial value 35 NTSC PAL 36 00 Fixed data-1 37 01 (Initialized data) 38 02 39 03 3A 04 3B 05 3C 06 3D 07 3E 08 3F 09 40 0A 41 0B 42 0C 43 0D 44 0E 45 0F 46 10 47 11 48 12 49 13 4A 14 4B 15 4C 16 4D 17 4E 18 4F 19 50 1A 51 1B 52 1C 53 1D 54 1E 55 1F 56 20 57 21 58 22 59 23 5A 24 5B 25 5C 26 5D 27 5E 28 5F 29 60 0F 0F CCD black defect compensation 2A 61 FF FF 2B 62 0F 0F 2C 63 FF FF 2D 64 0F 0F 2E 65 FF FF 2F 66 0F 0F 30 67 FF FF 31 68 0F 0F 32 69 FF FF 5-19, Remark Remark Address Initial value Address Initial value NTSC PAL NTSC PAL 6A 0F 0F CCD black defect compensation A1 FF FF CCD white defect compensation 6B FF FF A2 0F 0F 6C 0F 0F A3 FF FF 6D FF FF A4 Fixed data-1 6E 0F 0F A5 (Initialized data) 6F FF FF A6 70 0F 0F A7 71 FF FF A8 72 0F 0F A9 73 FF FF AA 74 0F 0F AB 75 FF FF AC 76 0F 0F AD 77 FF FF AE 78 0F 0F AF 79 FF FF Table. 5-1-6. 7A 0F 0F 7B FF FF 7C 0F 0F 7D FF FF 7E 0F 0F 7F FF FF 80 0F 0F 81 FF FF 82 0F 0F 83 FF FF 84 0F 0F 85 FF FF 86 0F 0F 87 FF FF 88 0F 0F CCD white defect compensation 89 FF FF 8A 0F 0F 8B FF FF 8C 0F 0F 8D FF FF 8E 0F 0F 8F FF FF 90 0F 0F 91 FF FF 92 0F 0F 93 FF FF 94 0F 0F 95 FF FF 96 0F 0F 97 FF FF 98 0F 0F 99 FF FF 9A 0F 0F 9B FF FF 9C 0F 0F 9D FF FF 9E 0F 0F 9F FF FF A0 0F 0F 5-20, 1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Adjustment 1. Video Sync Level Adjustment (Control Switch Block (FK) ) (Control Switch Block (FK) ) Adjust the burst level of the composite video signal output. Adjust the sync level of the composite video signal output. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Video terminal of AV OUT jack Measurement Point Video terminal of AV OUT jack (75Ω terminated) (75Ω terminated) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Adjustment Page F Adjustment Page F Adjustment Address 66 Adjustment Address 65 Specified Value A = 286 ± 5mV (NTSC) Specified Value A = 290 ± 5mV (NTSC) A = 300 ± 5mV (PAL) A = 305 ± 5mV (PAL) Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: 04. 2) Select page: 5, address: F1, and set data: 04. 3) Select page: F, address: 66, change the data and set the burst 3) Select page: F, address: 65, change the data and set the sync level (A) to the specified value. level (A) to the specified value. 4) Select page: 5, address: F1, and set data: 00. 4) Select page: 5, address: F1, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. 5) Select page: 0, address: 01, and set data: 00.

A A H

H Fig.5-1-11. Fig.5-1-10. 3. Video Y Level Check (Control Switch Block (FK) ) Confirm the Y level of the composite video signal output. Mode PLAY Signal Arbitrary Measurement Point Video terminal of AV OUT jack (75Ω terminated) Measuring Instrument Oscilloscope Specified Value A = 710 ± 20mV (NTSC) A = 695 ± 20mV (PAL) Adjusting method: 1) Select page: 5, address: F1, and set data: 04. 2) Check that the white (100 IRE) level (A) satisfies the specified value. 3) Select page: 5, address: F1, and set data: 00. White (100 IRE)

A H

Fig.5-1-12. 5-21, 1-4. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Mode STILL Subject Arbitrary Measurement Point Display data of page 1 (Note1) Measuring Instrument Adjustment remote commander Adjustment Page F Adjustment Address 2E, 2F, 34, 35 Specified Value 13 to 17 during IRIS OPEN 7A to 7E during IRIS CLOSE Note 1: Displayed data of page 1 of the adjustment remote commander. 1 : 00 : XX Display data Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 15. 3) Select page: 6, address: 95, and set data: 7C. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 2E, 2F, 34 and 35.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 0, address: 03, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the display data (Note1) during IRIS OPEN satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the display data during IRIS CLOSE satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 94, and set data: 00. 3) Select page: 6, address: 95, and set data: 00. 4) Select page: 0, address: 01, and set data: 00. 5) Select page: 0, address: 03, and set data: 00. 5-22, 2. Flange Back Adjustment Adjusting method: (Using Minipattern Box) 1) Install the minipattern box so that the distance between it and The inner focus lens flange back adjustment is carried out the front of the lens of the camera is less than 3cm. automatically. In whichever case, the focus will be deviated during 2) Make the height of the minipattern box and the camcorder equal. auto focusing/manual focusing. 3) Check that the output voltage of the regulated power supply is Mode STILL the specified voltage ± 0.01Vdc. 4) Select page: 0, address: 01, and set data: 01. Subject Siemens star chart with ND filter for 5) Select page: 5, address: F1, and set data: FF. the minipattern box (Note1) 6) Check that the center of the Siemens star chart and center of Measurement Point Check operation on TV monitor the exposure screen coincide. Measuring Instrument 7) Check that the data of page: F, address: 14 to 25 is the initial Adjustment Page F value (See table below). Adjustment Address 14 to 25 Address Data Address Data Address Data 14 1C 1A 00 20 20 Note 1: Dark Siemens star chart. 15 94 1B 00 21 20 Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the 16 26 1C 00 22 23 power of the unit OFF/ON. 17 EC 1D 00 23 44 Preparations before adjustments: 18 13 1E 46 24 0A The minipattern box is installed as shown in the following figure. 19 B9 1F 00 25 00 Note: The attachment lenses are not used. Specified voltage: The specified voltage varies according to the 8) Select page: 6, address: 01, set data: 13, and press the PAUSE minipattern box, so adjust the power supply button of the adjustment remote commander. output voltage to the specified voltage 9) Select page: 6, address: 01, set data: 27, and press the PAUSE written on the sheet which is supplied with button. the minipattern box. (The adjustment data will be automatically input to page: F, addresses: 14 to 25.) 10) Select page: 6, address: 02, and check that the data is changed Below 3 cm to “01”. Minipattern box Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE Camera button. 2) Select page: 5, address: F1, and set data: 00. Table 3) Select page: 0, address: 01, and set data: 00. 4) Perform “Flange Back Check”. Regulated power supply Output voltage: Specified voltage ± 0.01Vdc Output current: more than 3.5A Red (+) Black (–) Yellow (SENS +) White (SENS –) Need not connected Black (GND) Fig.5-1-13. 5-23, 3. Flange Back Adjustment 4. Flange Back Check (Using Flange Back Adjustment Chart) Mode STILL Subject Siemens star The inner focus lens flange back adjustment is carried out (2.0 m from the front of the lens) automatically. In whichever case, the focus will be deviated during (Luminance : approx. 200 lux) auto focusing/manual focusing. Measurement Point Check operation on TV monitor Mode STILL Measuring Instrument Subject Flange back adjustment chart Specified Value The lens is focused. (2.0 m from the front of the lens) (Luminance: 350 ± 50 lux) Checking method: 1) Place the Siemens star 2.0m from the front of the lens. Measurement Point Check operation on TV monitor 2) To open the IRIS, decrease the luminous intensity to the Measuring Instrument Siemens star up to a point before noise appear on the image. Adjustment Page F 3) Shoot the siemens star with the zoom TELE end. Adjustment Address 14 to 25 4) Turn on the auto focus 5) Observe the TV monitor and check that the lens is focused. Note: Check that the data of page: 6, address: 02 is “00”. If not, turn the 6) Select page: 0, address: 01, and set data: 01. power of the unit OFF/ON. 7) Select page: 5, address: F1, and set data: FF. 8) Select page: 6, address: 2C, and set data: 01. Adjusting method: 9) Shoot the siemens star with the zoom WIDE end. 1) Select page: 0, address: 01, and set data: 01. 10) Observe the TV monitor and check that the lens is focused. 2) Select page: 5, address: F1, and set data: FF. 3) Check that the center of the chart for the flange back adjustment Processing after Completing Adjustments: and center of the exposure screen coincide. 1) Select page: 6, address: 2C, and set data: 00. 4) Check that the data of page: F, address: 14 to 25 is the initial 2) Select page: 5, address: F1, and set data: 00. value (See table below). 3) Select page: 0, address: 01, and set data: 00. Address Data Address Data Address Data 14 1C 1A 00 20 20 15 94 1B 00 21 20 16 26 1C 00 22 23 17 EC 1D 00 23 44 18 13 1E 46 24 0A 19 B9 1F 00 25 00 5) Select page: 6, address: 01, set data: 13, and press the PAUSE button of the adjustment remote commander. 6) Select page: 6, address: 01, set data: 15, and press the PAUSE button. (The adjustment data will be automatically input to page: F, addresses: 14 to 25.) 7) Select page: 6, address: 02, and check that the data is changed to “01”. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 5, address: F1, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. 4) Perform “Flange Back Check”. 5-24, 5. Picture Frame Setting 6. F No. Standard Data Input Mode STILL Compensate the unevenness of the iris meter sensitivity. Subject Color bar chart Mode STILL (Color reproduction adjustment frame) Subject Clear chart (Approx. 90cm from the front of the lens) (Color reproduction adjustment frame) Measurement Point Video output terminal Adjustment Page F Measuring Instrument Oscilloscope and TV monitor Adjustment Address 29 to 2C Specified Value A=B, C=D, E=F Note: Check that the data of page: 6, address: 02 is “00”. If not, turn the Setting method: power of the unit OFF/ON. 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F1, and set data: FF. 1) Select page: 0, address: 01, and set data: 01. 3) Adjust the zoom, the direction and the distance between the pattern 2) Select page: 5, address: F1, and set data: FF. box and camera, and set the picture frame to the specified position. 3) Select page: 6, address: 01, set data: BB, and press the PAUSE 4) Mark the position of the picture frame on the monitor display, button of the adjustment remote commander. and adjust the picture frame to this position in following (The F No. standard data input is performed and the adjustment adjustments using “Color reproduction adjustment frame”. data is stored in page: F, address: 29 to 2C.) (Press the shutter and check with image input.) 4) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. Processing after Completing Adjustments: Check on an oscilloscope 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 1. Horizontal period 2) Select page: 5, address: F1, and set data: 00. A=B C=D 3) Select page: 0, address: 01, and set data: 00. BCAD7. Mechanical Shutter Adjustment Adjust the period which the mechanical shutter is closed, and compensate the exposure. Mode STILL Subject Clear chart (Focused at the WIDE end and Color reproduction adjustment frame) Adjustment Page F Adjustment Address 5A, 6C to 7F Note: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Adjusting method: Fig. 5-1-14. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: FF. 2. Vertical period 3) Select page: 6, address: 01, set data: AD, and press the PAUSE button of the adjustment remote commander. E E=F F (The mechanical shutter adjustment is performed and the adjustment data is stored in page: F, address: 5A, 6C to 7F.) 4) Select page: 6, address: 02, and check that the data changes to “01”. 5) Check page: 6, address AB. The adjustment has been performed V correctly if the data is 00 and incorrectly if other than 00. Fig. 5-1-15. Processing after Completing Adjustments: Check on the monitor TV (Underscanned mode) 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 5, address: F1, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. Color bar chart picture frame Monitor TV picture frame Fig. 5-1-16. 5-25, 8. AGC Standard Gain and Max Gain Adjustment 9. Light Level Adjustment and ND shutter check Adjust the AGC standard gain and max gain. Adjust the standard LV value. Mode STILL Mode STILL Subject Clear chart Subject Clear chart (Color bar standard picture frame) (Color bar standard picture frame) Adjustment PageEFMeasurement Point Display data of page 1 (Note 2) Adjustment Address 4F 27 Measuring Instrument Adjustment remote commander Adjustment Page F Note: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Adjustment Address 26, 28 Specified Value AE level 1: 0FE0 to 1020 Adjusting method: AE level 2: Below 1100 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: FF. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the 3) Select page: 6, address: 98, and set data: C0. power of the unit OFF/ON. 4) Select page: 6, address: 99, and set data: 26. Note 2: Displayed data of page 1 of the adjustment remote commander. 5) Select page: 6, address: 01, and set data: C7, and press the 1 : XX : XX PAUSE button of remote commander. (The AGC gain Display data adjustment is performed and the adjustment data is stored in page: E, address: 4F, and page: F, address 27.) Adjusting method: 6) Select page: 6, address: 02, and check that the data is “01”. 1) Select page: 0, address: 01, set data: 01 and press the PAUSE button. Processing after Completing Adjustments: 2) Select page: 5, address: F1, and set data: FF. 1) Select page: 6, address: 98, and set data: 00. 3) Select page: 6, address: 01, set data: 0D, and press the PAUSE 2) Select page: 6, address: 99, and set data: 00. button of the adjustment remote commander. 3) Select page: 6, address: 01, and set data: 00, and press the (The light level adjustment is performed and the adjustment PAUSE button. data is stored in page: F, address: 26, 28.) 4) Select page: 5, address: F1, and set data: 00. 4) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: 0, address: 01, and set data: 00. 5) Select page: 0, address: 03, set data: 06, and press the PAUSE button. 6) Select page: 1, and check that the display data (Note 2) satisfies the AE level 1 7) Select page: E, address: 41, set data: 6B, and press the PAUSE button. 8) Select page: 6, address: 1C, set data: 03, and press the PAUSE button. 9) Select page: 1, and check that the display data (Note 2) satisfies the AE level 2. Processing after Completing Adjustments: 1) Select page: 6, address: 01, and set data: 00. 2) Select page: E, address: 41, set data: 6A, and press the PAUSE button. 3) Select page: 6, address: 1C, and set data: 00. 4) Select page: 0, address: 03, and set data: 00. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-26, 10. Auto White Balance Standard Data Input 11. Auto White Balance ND Filter Compensation Adjust the white balance standard data at 3200K. Adjustment Mode STILL Adjust to the proper auto white balance output data with Built-in ND filter. Subject Clear chart If it is not correct, auto white balance and color reproducibility will (Color bar standard picture frame) be poor. Adjustment Page F Mode STILL Adjustment Address 3A to 3D, 59 Subject Clear chart Note: (Color reproduction adjustment frame)Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Filter Built-in ND filter Adjustment Page F Adjusting method: Adjustment Address 4F, 50 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: FF. 3) Select page: B, address: 41, and set data: 30. Note 1: Perform “Auto White Balance Standard Data Input” before this adjustment. 4) Select page: F, address: 37, and set data: 9B. Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the 5) Select page: 6, address: 01, set data: 11, and press the PAUSE power of the unit OFF/ON. button. 6) Select page: 6, address: 01, set data: 0B, and press the PAUSE Adjusting method: button. 1) Select page: 0, address: 01, and set data: 01. (The auto white balance standard data input is performed and 2) Select page: 5, address: F1, and set data: FF. the adjustment data is stored in page: F, address: 3A to 3D, 3) Select page: B, address: 41, set data: 30, and press the PAUSE 59.) button. 7) Select page: 6, address: 02, and check that the data is “01”. 4) Select page: 6, address: 1C, set data: 03, press PAUSE button and wait for one second. Processing after Completing Adjustments: 5) Select page: F, address: 37, and set data: 9B. 1) Select page: B, address: 41, and set data: 00. 6) Select page: 6, address: 01, set data: 11, and press the PAUSE 2) Select page: 6, address: 01, and set data: 00. button. 3) Select page: F, address: 37, set data: 93, and press the PAUSE 7) Select page: 6, address: 01, set data: 09, and press the PAUSE button. button. 4) Select page: 5, address: F1, and set data: 00. (The auto white balance adjustment ND filter compensation is 5) Select page: 0, address: 01, and set data: 00. performed and the adjustment data is stored in page: F, address: 4F and 50.) 8) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: 1) Select page: B, address: 41, and set data: 00. 2) Select page: 6, address: 1C, set data: 00, and press the PAUSE button. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 4) Select page: F, address: 37, set data: 93, and press the PAUSE button. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-27, 12. Auto White Balance Adjustment Processing after Completing Adjustments: Adjust to the proper auto white balance output data. 1) Select page: 0, address: 03, and set data: 00. If it is not correct, auto white balance and color reproducibility will 2) Select page: B, address: 41, set data: 00, and press the PAUSE be poor. button. Mode STILL 3) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Subject Clear chart 4) Select page: F, address: 37, set data: 93, and press the PAUSE (Color reproduction adjustment frame) button. Filter Filter C14 for color temperature 5) Select page: 5, address: F1, and set data: 00. correction 6) Select page: 0, address: 01, and set data: 00. Measurement Point Display data of page 1 (Note 3) Measuring Instrument Adjustment remote commander Adjustment Page F Adjustment Address 3F, 40, 80 Specified Value R ratio: 29E0 to 2B20 (Center: 2A80) B ratio: 5F20 to 6060 (Center: 5FC0) Note 1: Perform “Auto White Balance ND Filter Compensation Adjustment” and “Auto White Balance Standard Data Input” before this adjustment. Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Note 3: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data Adjusting method: 1) Place the C14 filter for color temperature correction on the lens. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 5, address: F1, and set data: FF. 4) Select page: B, address: 41, set data: 30, and press the PAUSE button. 5) Select page: F, address: 37, set data: 9B, and press the PAUSE button. 6) Select page: 6, address: 01, set data: A7, and press the PAUSE button. 7) Select page: F, address: 49 to 4C, and note down the data of each address. 8) Input the following data to page: F, addresses: 49 to 4C. Address 49 4A 4B 4C Data 2A 80 5F C0 Note: Press the PAUSE button of the adjustment remote commander each time to set the data. 9) Select page: 6, address: 01, set data: A5, and press the PAUSE button. (The auto white balance adjustment is performed and the adjustment data is stored in page: F, address: 3F, 40 and 80.) 10) Select page: 6, address: 02, and check that the data is “01”. 11) Select page: 6, address: 01, set data: 3F, and press the PAUSE button. 12) Select page: 0, address: 03, and set data: 04. 13) Select page: 1, and check that the display data (Note3) satisfies the R ratio specified value. 14) Select page: 0, address: 03, and set data: 05. 15) Select page: 1, and check that the display data (Note3) satisfies the B ratio specified value. 16) Select page: F, address: 49 to 4C, and input the data noted down at step 7). Note: After setting each data, be sure to press the PAUSE button of the adjustment remote commander. 5-28, 13. Color Reproduction Adjustment 13-2. Color Reproduction Adjustment (With ND Filter) Adjust the color Separation matrix coefficient so that proper color Mode STILL reproduction is produced. Subject Color bar chart (Color bar standard picture frame) 13-1. Color Reproduction Adjustment (Without ND Filter) Adjustment Page F Mode STILL Adjustment Address 51 to 58, 60 to 63 Subject Color bar chart (Color bar standard picture frame) Note 1: This adjustment should be carried out upon completion of “Auto Adjustment Page F White Balance Standard Data Input” and “Auto White Balance Adjustment Address 41 to 48, 5C to 5F ND Filter Compensation Adjustment”. Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Note 1: This adjustment should be carried out upon completion of “Auto White Balance Standard Data Input” and “Auto White Balance Adjustment”. Adjusting method: Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the 1) Select page: 0, address: 01, and set data: 01. power of the unit OFF/ON. 2) Select page: 5, address: F1, and set data: FF. 3) Check that the picture frame is set to the specified position. Adjusting method: (Refer to “5. Picture Frame Setting”.) 1) Select page: 0, address: 01, and set data: 01. 4) Select page: B, address: 41, set data: 30, and press the PAUSE 2) Select page: 5, address: F1, and set data: FF. button. 3) Check that the picture frame is set to the specified position. 5) Select page: F, address: 37, set data: 9B, and press the PAUSE (Refer to “5. Picture Frame Setting”.) button. 4) Select page: B, address: 41, set data: 30, and press the PAUSE 6) Select page: 6, address: 1C, set data: 03, press PAUSE button, button. and wait for one second. 5) Select page: F, address: 37, and set data: 9B. 7) Select page: 6, address: 12, set data: 80, press PAUSE button, 6) Select page: 6, address: 01, set data: AB, and press the PAUSE and wait for two seconds. button. 8) Select page: 6, address: 12, set data: 00, press PAUSE button, 7) Select page: 6, address: 01, set data: A9, and press the PAUSE and wait for two seconds. button. 9) Select page: 6, address: 01, set data: C3, and press the PAUSE (The color reproduction adjustment (without ND filter) is button. performed and the adjustment data is stored in page: F, address: 10) Select page: 6, address: 01, set data: C1, and press the PAUSE 41 to 48 and 5C to 5F.) button. 8) Select page: 6, address: 02, and check that the data is “01”. (The color reproduction adjustment (with ND filter) is 9) Perform “Color Reproduction Check” and “Processing after performed and the adjustment data is stored in page: F, address: Completing Adjustments”. 51 to 58 and 60 to 63.) 11) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: 12) Perform “Color Reproduction Check” and “Processing after 1) Select page: B, address: 41, set data: 00, and press the PAUSE Completing Adjustments”. button. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE Processing after Completing Adjustments: button of the adjustment remote commander. 1) Select page: B, address: 41, set data: 00, and press the PAUSE 3) Select page: F, address: 37, set data: 93, and press the PAUSE button. button. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE 4) Select page: 5, address: F1, and set data: 00. button of the adjustment remote commander. 5) Select page: 0, address: 01, and set data: 00. 3) Select page: 6, address: 1C, set data: 00, and press the PAUSE button of the adjustment remote commander. 4) Select page: F, address: 37, set data: 93, and press the PAUSE button. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-29, 13-3. Color Reproduction Check Processing after Completing Adjustments: Mode STILL 1) Select page: E, address: 52, set the data noted down at step 2), and press the PAUSE button of the adjustment remote Subject Color bar chart commander. (Color reproduction adjustment frame) 2) Select page: B, address: 41, set data: 00, and press the PAUSE Measurement Point Video output terminal button. Measuring Instrument Vectorscope 3) Select page: 6, address: 01, set data: 00, and press the PAUSE Specified Value Each center of all color luminance button. points should settle within each color 4) Select page: 6, address: 1C, set data: 00, and press the PAUSE reproduction frame. button. 5) Select page: F, address: 37, set data: 93, and press the PAUSE Note: This check should be performed at NTSC mode only. button. (Click MENU button [SETUP] [VIDEO OUT] [NTSC].) 6) Select page: 6, address: 10, and set data: 00. 7) Select page: 5, address: F1, and set data: 00. Checking method: 8) Select page: 0, address: 01, and set data: 00. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: E, address: 52, after noting down the data, set data: 0B, and press the PAUSE button of the adjustment remote commander. 3) Select page: 5, address: F1, and set data: FF. 4) Select page: B, address: 41, set data: 30, and press the PAUSE button. 5) Select page: F, address: 37, set data: 9B, and press the PAUSE button. 6) Select page: 6, address: 10, and set data: 01. 7) Select page: 6, address: 01, set data: 0F, and press the PAUSE button. 8) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 9) Check that each center of all color luminance points is settled in each color reproduction frame. 10) Select page: 6, address: 1C, set data: 03, press the PAUSE button and wait for one second. 11) Select page: 6, address: 12, set data: 80, press the PAUSE button and wait for two seconds. 12) Select page: 6, address: 12, set data: 00, press the PAUSE button and wait for two seconds. 13) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 14) Check that each center of all color luminance points is settled in each color reproduction frame. NTSC mode R-Y

MG R YL B CY G

Burst position Fig.5-1-17. 5-30, 14. White Balance Check 15. Strobe White Balance Adjustment Mode STILL Adjust the white balance when the strobe light flashes. Subject Clear chart Mode STILL (Color reproduction adjustment frame) Subject Flash adjustment box (Note5) Filter Filter C14 for color temperature (1.0m from the front of the lens) correction Adjustment Page F ND filter 1.0 and 0.4 and 0.1 Adjustment Address 4D, 4E, 68, 69, 6A, 6B Measurement Point Video output terminal Measuring Instrumen Vectorscope Note 1: Perform this adjustment in the flash adjustment box. Note 2: Any light other than the strobe light should not light up the plate. Specified Value Fig. 5-1-16. A to C Note 3: This adjustment should be carried out upon completion of “HALL Adjustment”, “Flange Back Adjustment”, “Light Level Checking method: Adjustment” and “Auto White Balance Adjustment”. 1) Check that the lens is not covered with either filter. Note 4: Check that the data of page: 6, address: 02 is “00”. If not, turn the 2) Select page: 0, address: 01, and set data: 01. power of the unit OFF/ON. 3) Select page: 5, address: F1, and set data: FF. Note 5: Refer to “4. Preparing the Flash Adjustment Box”. (See page 5-7) 4) Select page: B, address: 41, set data: 30, and press the PAUSE button. Adjusting method: 5) Select page: F, address: 37, set data: 9B, and press the PAUSE button. 1) Select page: 0, address: 01, and set data: 01. 6) Select page: 6, address: 01, set data: 0F, and press the PAUSE 2) Select page: 5, address: F1, and set data: FF. button of the adjustment remote commander. 3) Select page: B, address: 41, set data: 30, and press the PAUSE 7) Check that the center of the white luminance point is within button. the circle shown Fig. 5-1-16. (A). 4) Select page: 6, address: 90, and set data: 00. 8) Select page: 6, address: 1C, set data: 03, and press the PAUSE 5) Select page: 6, address: 91, and set data: 00. button and wait for one second. 6) Select page: 6, address: 92, and set data: 00. 9) Check that the center of the white luminance point is with in 7) Select page: 6, address: 93, and set data: 60. the circle shown Fig. 5-1-18. (A). 8) Select page: 6, address: 2C, and set data: 01. 10) Select page: 6, address: 1C, set data: 00, and press the PAUSE 9) Select page: 6, address: 01, set data: 79, and press the PAUSE button. button. 11) Select page: 6, address: 01, set data: 23, and press the PAUSE 10) Select page: 6, address: 01, set data: B9, and press the PAUSE button. button. 12) Place the C14 filter on the lens. 11) Check the flashing of the strobe light. 13) Check that the center of the white luminance point settles in (The strobe white balance adjustment is performed and the the circle shown Fig. 5-1-18. (B). adjustment data is stored in page: F, address: 4D, 4E, 68, 69, 14) Remove the C14 filter, and place the ND filter 1.5 (1.0 +0.4+0.1) 6A and 6B.) on the lens. 12) Select page: 6, address: 02, and check that the data is “01”. 15) Check that the white luminance point stopped moving, and then remove the ND filter 1.5. Processing after Completing Adjustments: 16) Check that the center of the white luminance point settles within 1) Select page: 6, address: 2C, and set data: 00. the circle shown Fig. 5-1-18. (C). 2) Select page: 6, address: 93, and set data: 00. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: B, address: 41, and set data: 00. 4) Select page: B, address: 41, set data: 00, and press the PAUSE 2) Select page: F, address: 37, and set data: 93. button. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 5) Select page: 5, address: F1, and set data: 00. 4) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. R-Y 3mm 0.5mm B-Y 3mm Fig.5-1-18.(A) R-Y B-Y 2.0mm 6mm 6mm Fig.5-1-18.(B) R-Y 1.0mm 6mm B-Y 6mm Fig.5-1-18.(C) 5-31, 16. Strobe Light Level and White Balance Check 17. CCD Black Defect Compensation Check the light level regulation and the white balance when the Mode STILL strobe light flashes. Subject Clear chart Mode STILL (25 cm from the front of the lens) Subject Flash adjustment box (Note4) (Note1) (1.0m from the front of the lens) Measurement Point Display data of page: 6, address: 55 Measurement Point Display data of page: 1 Measuring Instrument Adjustment remote commander Measuring Instrument Adjustment remote commander Adjustment Page 7 Specified value Y level data: 68 to A0 (Note6) Adjustment Address 60 to 87 R-Y data: FA to FF or 00 to 06 (Note7) Specified value Data < 0A: OK, Data > 0B: NG B-Y data: FA to FF or 00 to 06 (Note7) Note 1: Perform this adjustment in the flash adjustment box. Note 1: Check that there are no dust, no dirt and no reflection on the clear Note 2: Any light other than the strobe light should not light up the plate. chart. Note 3: This adjustment should be carried out upon completion of Note 2: Any subject other than the clear chart should not be in the screen. “HALL Adjustment”, “Flange Back Adjustment”, “Light Level Adjustment”, “Auto White Balance Adjustment” and “Strobe White Adjusting method: Balance Adjustment”. 1) Select page: 0, address: 01, and set data: 01. Note 4: Refer to “4. Preparing the Flash Adjustment Box”. (See page 5-7) 2) Select page: 5, address: F1, and set data: FF. Note 5: Check that the data of page: 6, address: 02 is “0”. If not, turn the 3) Select page: F, address: DF, after noting down the data, set power of the unit OFF/ON. data: 4C, and press the PAUSE button. Note 6: Display data of page 1 of the adjustment remote commander. 1 : 00 : XX 4) Select page: 6, address: 2C, and set data: 01. Y level data 5) Select page: 6, address: 90, and set data: 00. Note 7: Display data of page 1 of the adjustment remote commander. 6) Select page: 6, address: 91, and set data: 03. 1 : XX : XX 7) Select page: 6, address: 92, and set data: 00. B-Y data 8) Select page: 6, address: 93, and set data: 00. R-Y data 9) Select page: 6, address: 01, set data: 79, and press the PAUSE button. Checking method: 10) Select page: 6, address: 30, set data: 07, and wait for four 1) Select page: 0, address: 01, and set data: 01. seconds. 2) Select page: 5, address: F1, and set data: FF. 11) Select page: 6, address: 01, set data: 8D, and press the PAUSE 3) Select page: 6, address: 90, and set data: 00. button. 4) Select page: 6, address: 91, and set data: 00. (The CCD Block defect compensation is performed and the 5) Select page: 6, address: 92, and set data: 00. adjustment data is stored in page: 7, address: 60 to 87.) 6) Select page: 6, address: 93, and set data: 60. 12) Select page: 6, address: 02, and check that the data changes to 7) Select page: 6, address: 2C, and set data: 01. “01”. 8) Select page: 6, address: 01, set data: 79, and press the PAUSE 13) Select page: 6, address: 55 and check that the data satisfies button. specified value. 9) Select page: 6, address: 01, set data: 67, and press the PAUSE (This value means the number of the Black CCD defect.) button. 10) Check the flashing of the strobe light. Processing after Completing Adjustments: 11) Select page: 0, address: 03, and set data: 01. 1) Select page: F, address: DF, set the data noted down at step 3), 12) Select page: 1, and check that the Y level data satisfies the and press the PAUSE button. specified value. (Note6) 2) Select page: 6, address: 01, and set data: 00, and press the 13) Select page: 0, address: 03, and set data: 02. PAUSE button of the adjustment remote commander. 14) Select page: 1, and check that the R-Y data and B-Y data satisfy 3) Select page: 6, address: 2C, and set data: 00. the specified value respectively.(Note7) 4) Select page: 6, address: 91, and set data: 00. 5) Select page: 6, address: 30, and set data: 00. Processing after Completing Adjustments: 6) Select page: 5, address: F1, and set data: 00. 1) Select page: 0, address: 03, and set data: 00. 7) Select page: 0, address: 01, and set data: 00. 2) Select page: 6, address: 2C, and set data: 00. 3) Select page: 6, address: 93, and set data: 00. 4) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 5) Select page: E, address: 8F, set data: 01, and press the PAUSE button. 6) Select page: E, address: 6F, set data: 24, and press the PAUSE button. 7) Select page: E, address: 71, set data: 10, and press the PAUSE button. 8) Select page: F, address: B9, set data: 00, and press the PAUSE button. 9) Select page: 5, address: F1, and set data: 00. 10) Select page: 0, address: 01, and set data: 00. 5-32, 18. CCD Black Defect Compensation Check Processing after Completing Adjustments: Mode STILL 1) Select page: F, address: DF, set the data noted down at step 5), and press the PAUSE button. Subject Clear chart 2) Select page: 6, address: 01, and set data: 00, and press the (25 cm from the front of the lens) PAUSE button of the adjustment remote commander. (Note1) 3) Select page: 6, address: 2C, and set data: 00. Measurement Point Display data of page: 6, address: 55 4) Select page: 6, address: 30, and set data: 00. Measuring Instrument Adjustment remote commander 5) Select page: 6, address: 91, and set data: 00. Specified Value 00 6) Select page: 5, address: F1, and set data: 00. 7) Select page: 0, address: 01, and set data: 00. Note 1: Check that there are no dust, no dirt and no reflection on the clear chart. Note 2: Any subject other than the clear chart should not be in the screen. Note 3: This adjustment should be carried out upon completion of “CCD Black Defect Compensation”. Checking method: 1) Turn the power of the unit OFF and then ON. 2) Wait until the camera picture appear on the screen. 3) Select page: 0, address: 01, and set data: 01. 4) Select page: 5, address: F1, and set data: FF. 5) Select page: F, address: DF, after noting down the data, set data: 5A, and press PAUSE button. 6) Select page: 6, address: 2C, and set data: 01. 7) Select page: 6, address: 90, and set data: 00. 8) Select page: 6, address: 91, and set data: 03. 9) Select page: 6, address: 92, and set data: 00. 10) Select page: 6, address: 93, and set data: 00. 11) Select page: 6, address: 01, and set data: 79. 12) Select page: 6, address: 30, set data: 07, and wait for four seconds. 13) Select page: 6, address: 01, set data: 89, and press the PAUSE button. 14) Select page: 6, address: 02, and check that the data changes to “01”. 15) Select page: 6, address: 55, and check that the data is “00”. (If the data is other than “00”, black defect compensation has errors.) 5-33, 19. CCD White Defect Compensation 20. CCD White Defect Compensation Check Mode STILL Mode STILL Subject Clear chart Subject Clear chart (25 cm from the front of the lens) (25 cm from the front of the lens) (Note1) (Note1) Measurement Point Display data of page: 6, address: 55 Measurement Point Display data of page: 6, address: 55 Measuring Instrument Adjustment remote commander Measuring Instrument Adjustment remote commander Adjustment Page 7 Specified Value 00 Adjustment Address 88 to A3 Note 1: Check that there are no dust, no dirt and no reflection on the clear Specified value Data < 7F: OK, Data > 80: NG chart. Note 2: Any subject other than the clear chart should not be in the screen. Note 1: Check that there are no dust, no dirt and no reflection on the clear Note 3: This adjustment should be carried out upon completion of chart. “CCD White Defect Compensation”. Note 2: Any subject other than the clear chart should not be in the screen. Checking method: Adjusting method: 1) Turn the power of the unit OFF and then ON. 1) Select page: 0, address: 01, and set data: 01. 2) Wait until the camera picture appear on the screen. 2) Select page: 5, address: F1, and set data: FF. 3) Select page: 0, address: 01, and set data: 01. 3) Select page: F, address: DE, after noting down the data, set 4) Select page: 5, address: F1, and set data: FF. data: 14, and press the PAUSE button of the adjustment remote 5) Select page: F, address: DE, after noting down the data set data: commander. 0A, and press the PAUSE button. 4) Select page: F, address: E3, after noting down the data, set data: 6) Select page: F, address: E3, after noting down the data, set data: 28, and press the PAUSE button. 80, and press the PAUSE button. 5) Select page: 6, address: 01, set data: 8B, and press the PAUSE 7) Turn the power of the unit OFF and wait for four seconds. button. 8) Turn the power of the unit ON. (The CCD white defect compensation is performed and the 9) Select page: 0, address: 01, and set data: 01. adjustment data is stored in page: 7, address: 88 to A3.) 10) Select page: 6, address: 55, and check that the data is “00”. (If 6) Select page: 6, address: 02, and check that the data changes to the data is other than “00”, white defect compensation has “01”. errors.) 7) Select page: 6, address: 55, and check the data satisfies specified 11) Select page: F, address: E3, set data: A0, and press the PAUSE value. button. 12) Select page: 6, address: 01, set data: 87, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: F, address: DE, set the data noted down at step 3), 13) Select page: 6, address: 02, and check that the data changes to and press the PAUSE button. “01”. 2) Select page: F, address: E3, set the data noted down at step 4), 14) Select page: 6, address: 55, and check that the data is “00”. (If and press the PAUSE button. the data is other than “00”, black defect compensation has 3) Select page: 6, address: 01, and set data: 00, and press the errors.) PAUSE button of the adjustment remote commander. 4) Select page: 5, address: F1, and set data: 00. Processing after Completing Adjustments: 5) Select page: 0, address: 01, and set data: 00. 1) Select page: F, address: DE, set the data noted down at step 5), and press the PAUSE button. 2) Select page: F, address: E3, set the data noted down at step 6), and press the PAUSE button. 3) Select page: 6, address: 01, and set data: 00, and press the PAUSE button of the adjustment remote commander. 4) Select page: 5, address: F1, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. 5-34, 1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input Before perform the LCD system adjustments, check that the specified Mode PLAY values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Signal Arbitrary Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to Adjustment Page D avoid electrical shock. Adjustment Address 1C, 1D, 80 to 88, 8D to 8F Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Adjusting method: Note 3: Set the LCD BRIGHT to the center. 1) Select page: 0, address:01, and set data: 01. [Adjusting connector] 2) Select page: D, and input the data in the following table. Note: To write in the non-volatile memory (EEPROM), press the Most of the measuring points for adjusting the LCD system are PAUSE button of the adjustment remote commander each time concentrated in CN002 of the Control Switch Block (FK). to set the data. Connect the Measuring Instruments via the CPC-9 jig (J-6082-393- 3) Select page: 0, address:01, and set data: 00. C, Note4). To operate the adjustment remote commander, connect the power supply terminal of CPC-9 jig to the DC power supply Address Data Remark (6.0 to 7.2Vdc). 1C 00 Fixed data The following table shows the Pin No. and signal name of CN002. 1D 2C Fixed data Note 4: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, 80 BC Bright adj. because it cannot operate the adjustment remote commander. 81 80 Color adj. Pin No. Signal Name Pin No. Signal Name 82 B9 White balance adj. 1 NC 10 HI UNREG 83 B7 White balance adj. 2 NC 11 LANC IN 84 BE Contrast adj. 3 NC 12 LANC OUT 85 C8 D range adj. 4 REG GND 13 NC 86 7C V-COM level adj. 5 NC 14 RF7 VCO adj. (NTSC) 87 50 6 SYS V 15 TXD Fixed data (PAL) 7 HSY 16 RXD 88 74 V-COM adj. 8 PANEL COM 17 RESET VCO adj. (PAL) 8D 50 9 VG 18 VDD Fixed data (NTSC) 8E 13 Fixed data Table 5-1-7. 8F 11 Fixed data Slide the Release knob in the direction of arrow A. Control switch block (FK) To open the Battery lid. (CN002) 18

A

CPC-9 jig (18p flexible board) Two claws CPC cover Release knob Note : Don't use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit Fig.5-1-19. 5-35, 2. VCO Adjustment (Control Switch Block (FK) ) 3. D Range Adjustment (Control Switch Block (FK) ) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the RGB decoder used to drive the LCD to the be blurred. specified value. If deviated, the LCD screen will become blackish Mode PLAY or saturated (whitish). Signal Arbitrary Mode PLAY Measurement Point Pin 7 of CN002 (HSY) Signal Arbitrary Measuring Instrument Frequency counter Measurement Point Pin 9 of CN002 (VG) External trigger: Pin 8 of CN002 Adjustment Page D (PANEL COM) Adjustment Address 87 (NTSC) Measuring Instrument Oscilloscope 8D (PAL) Adjustment Page D Specified Value f = 15734 ± 30Hz (NTSC) f = 15750 ± 30Hz (PAL) (Note) Adjustment Address 85 Specified Value A = 3.62 ± 0.05V Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F0, set data: 01. 1) Select page: 0, address: 01, and set data: 01. 3) For NTSC model, select page: D, address: 87, change the data 2) Select page: 5, address: F1, set data: 03. and set the frequency (f) to the specified value. 3) Select page: D, address: 85, change the data and set the voltage For PAL model, select page: D, address: 8D, change the data (A) between the reversed waveform pedestal and non-reversed and set the frequency (f) to the specified value. waveform pedestal to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F0, set data: 00. 5) Select page: 5, address: F1, set data: 00. 6) Select page: 0, address: 01, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. Note : This specified value is the adjustment value for the NTSC Pedestal mode. If using for the PAL mode, be sure to switch VIDEO OUT to the NTSC mode at menu setup before performing adjustments. After adjusting, be sure to switch to the PAL mode.

A

Pedestal 2H Fig.5-1-20. 5-36, 4. Bright Adjustment (Control Switch Block (FK) ) 5. Contrast Adjustment (Control Switch Block (FK) ) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value. If deviated, the screen image will be blackish or saturated (whitish). (whitish). Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 9 of CN002 (VG) Measurement Point Pin 9 of CN002 (VG) External trigger: Pin 8 of CN002 External trigger: Pin 8 of CN002 (PANEL COM) (PANEL COM) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Adjustment Page D Adjustment Page D Adjustment Address 80 Adjustment Address 84 Specified Value A = 2.17 ± 0.08V Specified Value A = 3.31 ± 0.07V Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, set data: 03. 2) Select page: 5, address: F1, set data: 03. 3) Select page: 2, address: 10, and set data: 01. 3) Select page: D, address: 84, change the data and set the voltage 4) Select page: D, address: 80, change the data and set the voltage (A) between the 10 steps peak and pedestal to the specified (A) between the pedestal and GAMMA1 limiter level to the value. specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F1, set data: 00. 6) Select page: 2, address: 10, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 7) Select page: 5, address: F1, set data: 00. 8) Select page: 0, address: 01, and set data: 00. GAMMA1 limiter level 10 steps peak

A A

Pedestal Pedestal 2H 2H Fig.5-1-21. Fig.5-1-22. 5-37, 6. Color Adjustment (Control Switch Block (FK) ) 7. V-COM Level Adjustment (Control Switch Block (FK) ) Set the color saturation to the standard value. If deviated, the color Set the common electrode drive signal level of LCD to the specified will be to dark or light. value. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 9 of CN002 (VG) Measurement Point Pin 8 of CN002 (PANEL COM) External trigger: Pin 8 of CN002 Measuring Instrument Oscilloscope (PANEL COM) Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address 86 Adjustment Page D Specified Value A= 6.50 ± 0.05V Adjustment Address 81 Specified Value A= 544 ± 50mV Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F1, set data: 03. 1) Select page: 0, address: 01, and set data: 01. 3) Select page: D, address: 86, change the data and set the COM 2) Select page: 5, address: F1, set data: 04. signal level (A) to the specified value. 3) Select page: D, address: 81, change the data and set the voltage 4) Press the PAUSE button of the adjustment remote commander. (A) between the white 100% (Reference level) and green to 5) Select page: 5, address: F1, set data: 00. the specified value. 6) Select page: 0, address: 01, and set data: 00. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F1, set data: 00. 6) Select page: 0, address: 01, and set data: 00. White (100%) GreenAA2H Fig.5-1-24. 2H Fig.5-1-23. 5-38, 8. V-COM Adjustment 9. White Balance Adjustment (HI-70 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode PLAY conspicuous vertical lines. Signal Arbitrary Mode PLAY Measurement Point Check on LCD display Signal Arbitrary Measuring Instrument Measurement Point Check on LCD display Adjustment Page D Measuring Instrument Adjustment Address 82, 83 Adjustment Page D Specified Value The LCD screen should not be colored. Adjustment Address 88 Specified Value The brightness difference between the Note 1: Use the AC power adaptor during this adjustment. section A and section B is minimum. Note 2: Check the white balance only when replacing the following parts. If necessary, adjust them. Note 1 : Perform “Bright Adjustment” and “Contrast Adjustment” before 1. LCD panel this adjustment. 2. Light induction plate 3. IC802 (LCD DRIVE) Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F1, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 3) Select page: 2, address: 10, and set data: 02. 2) Select page: 5, address: F1, set data: 02. 4) Select page: D, address: 88, change the data so that the 3) If used AC adapter, select page: D, address: 1C, after noting brightness of the section A and that of the section B is equal. the data, set data: 00, and press PAUSE button. 5) Press the PAUSE button of the adjustment remote commander. If used battery, select page: D, address: 1D, after noting the 6) Select page: 5, address: F1, and set data: 00. data, set data: 0C. 7) Select page: 2, address: 10, and set data: 00. 4) Select page: D, address: 82 and 83, set the data to the initial 8) Select page: 0, address: 01, and set data: 00. value. Note: Press the PAUSE button of the adjustment remote commander each time to set the data. A Address 82 83B Data B9 B7AB5) Check that the LCD screen is not colored. If colored, change the data of page: D, address: 82 and 83 so that the LCD screen is not colored. B A Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. A B 6) Select page: D, address: 1C or 1D, set the data noted down at step 3). Fig.5-1-25. 7) Select page: 5, address: F1, and set data: 00. 8) Select page: 0, address: 01, and set data: 00. 5-39, 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Battery End Adjustment (SY-56 board) Check the battery end voltage. Mode STILL Subject Arbitrary Measurement Point Display data of page: 2, address: 51 Measuring Instrument Adjustment remote commander Adjustment Page D Adjustment Address 30 to 34, 4A Connection: 1) Connect the regulated power supply and the digital voltmeter to the battery terminal as shown in Fig. 5-1-24. Adjusting method: 1) Adjust the output voltage of the regulated power supply so that the digital voltmeter display is 3.5 ± 0.1Vdc. 2) Turn off the power supply. 3) Turn on the HOLD switch of the adjustment remote commander. 4) Turn on the power supply. 5) Insert the memory stick to the unit, and set to the STILL mode. 6) Set the FOCUS switch MANUAL side. 7) Select page: 0, address: 01, and set data: 01. 8) Decrease the output voltage of the regulated power supply so that the digital voltmeter display is 3.00 ± 0.01Vdc. 9) Select page: 2, address: 51, read the data, and this data is named Vref. 10) Select page: D, address: 30, set data: Vref, and press the PAUSE button of the adjustment remote commander. 11) Convert Dref to decimal notation, and obtain Dref’. (Refer to Table 5-2-1. “Hexadecimal-decimal conversion table” of “5-2. Service mode”) 12) Calculate V31', V32', V33', V34' and V4A' using following equations (decimal calculation), convert it to a hexadecimal number, and input each adjustment address. Address: 31 V31' = Vref’+3 Address: 32 V32' = Vref’+10 Address: 33 V33' = Vref’+10 Address: 34 V34' = Vref’+10 Address: 4A V4A' = Vref’+17 Note: After setting each data, be sure to press the PAUSE button. 13) Select page: 0, address: 01, and set data: 00. Regulated power supply (3.5 ± 0.1 Vdc) 1 3 CN001 Digital voltmeter DD-131 BOARD Fig.5-1-26. 5-40, 5-2. SERVICE MODE 2-1. ADJUSTMENT REMOTE COMMANDER The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Using the adjustment remote commander 2. Precautions upon using 1) Connect the adjustment remote commander to the Control the adjustment remote commander Switch Block (FK) CN002 via CPC-9 jig (J-6082-393-C). To Mishandling of the adjustment remote commander may erase the operate the adjustment remote commander, connect the DC correct adjustment data at times. To prevent this, it is recommended input terminal of CPC-9 jig to the DC power supply (6.0 to that all adjustment data be noted down before beginning adjustments 7.2Vdc). and new adjustment data after each adjustment. 2) Set the HOLD switch of the adjustment remote commander to “HOLD” (SERVICE position). If it has been properly connected, the LCD on the adjustment remote commander will display as shown in Fig. 5-2-1. Page Data Address Fig. 5-2-1. 3) Operate the adjustment remote commander as follows. • Changing the page The page increases when the EDIT SEARCH+ button is pressed, and decreases when the EDIT SEARCH– button is pressed. There are altogether 16 pages, from 0 to F. Hexadecimal notation0123456789ABCDEFLCD Display0123456789AbcdEFDecimal notation conversion value0123456789101112131415 • Changing the address The address increases when the FF ()) button is pressed, and decreases when the REW (0) button is pressed. There are altogether 256 addresses, from 00 to FF. • Changing the data (Data setting) The data increases when the PLAY ( ) button is pressed, and decreases when the STOP (p) button is pressed. There are altogether 256 data, from 00 to FF. • Writing the adjustment data The PAUSE button must be pressed to write the adjustment data (B, D, E, F page) in the nonvolatile memory. (The new adjusting data will not be recorded in the nonvolatile memory if this step is not performed.) 4) After completing all adjustments, turn off the main power supply once. 5-41, 2-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Indicates the hexadecimal-decimal conversion table. Hexadecimal-decimal Conversion Table 2 Lower digit of hexadecimal0123456789ABCDEFUpper digit (A) (b) (c) (d) (E) (F) of hexadecimal0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 77 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 1751B(b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander. (Example) If the DDS display or the adjustment remote commander shows BD (bd); Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number. Table. 5-2-1. 5-42, 2-3. SERVICE MODE 2. Bit value discrimination Bit values must be discriminated using the display data of the 1. Setting the Test Mode adjustment remote commander for following items. Use the table Page D Address 10 below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander Data Function 00 Normal 01 Forced STILL mode power ON 02 Forced PLAY mode power ON 03 Forced MOVIE mode power ON Address • Before setting the data , select page: 0, address: 01, and set data: Page bit3 to bit0 discrimination 01. • For page D, the data set is recorded in the non-volatile memory bit7 to bit4 discrimination by pressing the PAUSE button of the adjustment remote commander. In this case, take note that the test mode will not be Display on the Bit values exited even when the main power is turned off. adjustment bit3 bit2 bit1 bit0 • After completing adjustments/repairs, be sure to return the data remote or or or or of this address to “00”, and press the PAUSE button of the commander bit7 bit6 bit5 bit4 adjustment remote commander. 00000Select page: 0, address: 01, and set data: 00. 10001200103001140100501016011070111A8100091001A(A) 1010B(b) 1011C(c) 1100D(d) 1101BE(E) 1110F(F) 1111Example: If “8E” is displayed on the adjustment remote commander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. 5-43, 3. Switch check (1) Page 2 Address 43 Bit Function When bit value=1 When bit value=0 XPOWER SW 0 OFF ON (PW block) XCAM/PLAY SW 1 PLAY CAMERA STILL (PW block) (MOVIE ( SHUTTR SW 2 OFF ON (PW block) XSHUTTER LOCK SW 3 OFF ON (PW block) MEMORY STICK IN SW 4 IN OUT (HI-70 board) XSTILL/MOVIE SW 7 MOVIE STILL (PW block) Using method: 1) Select page: 2, address: 43. 2) By discriminating the bit value of display data, the state of the switches can be discriminated. 4. Switch check (2) Page 2 Address 54 to 56 Using method: 1) Select page: 2, address: 54 to 56. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 to 13 14 to 3A 3B to 63 64 to 90 91 to BC BD to E8 E9 to FF 54 LENS LENS ZOOM + ZOOM – (KEY AD 0) REVERSE NORMAL (FK block) (FK block) (IC603 &•) (MF block) (MF block) 55 CONTROL LCD LCD CONTROL UP DISPLAY (KEY AD 1) DOWN BRIGHT + BRIGHT – No key input (FK block) (FK block) (IC603 &ª) (FK block) (FK block) (FK block) 56 CONTROL CONTROL CONTROL LCD BACKLIGHT LCD BACKLIGHT

FLASH

(KEY AD 2) RIGHT LEFT SET OFF ON (FK block) (IC603 *º) (FK block) (FK block) (FK block) (FK block) (FK block) 58 SPOT FOCUS FOCUS MACRO WHT BAL (KEY AD 4) METER MANUAL AUTO (MF unit) (MF unit) (IC603 *™) (MF unit) (MF unit) (MF unit) (MF unit) 5. LED check Page 2 Address 06 Bit1 Using method: 1) Select page: 2, address: 06, and set the bit value of Bit1 to “1”. 2) Check that all LED except for the ACCESS LED are lit. 3) Select page: 2, address: 06, and set the bit value of Bit1 to “0”. 5-44E,

DSC-F505 SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they are The components identified by Les composants identifiés par une seldom required for routine service. Some delay mark ! or dotted line with mark marque ! sont critiques pour la should be anticipated when ordering these items. ! are critical for safety. sécurité. • The mechanical parts with no reference number in Replace only with part number Ne les remplacer que par une the exploded views are not supplied. specified. piéce portant le numéro spécifié. 6-1-1. BATTERY HOLDER ASSEMBLY 11 6 18 not supplied 13 13 12 6 not supplied 6 10 417 not supplied BT90186515 Rear cabinet assembly (See page 6-3) not supplied 17 17 12 not supplied not supplied 17 7 12 17 3 14 6 not supplied 17 17 Lens cabinet assembly (See page 6-4) 17 Front cabinet assembly (See page 6-2) not supplied 17 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3949-845-1 HOLDER ASSY, BATTERY 11 3-056-768-01 COVER, CPC 2 3-056-764-02 COVER, HINGE 12 3-713-791-01 SCREW (M1.7x4), TAPPING, P2 3 A-7074-101-A DD-131 BOARD, COMPLETE 13 3-736-363-41 TAPPING 4 A-7094-685-A HI-70 BOARD, COMPLETE (SERVICE) 14 1-960-051-11 HARNESS (MD-97) 5 1-675-589-21 FP-132 FLEXIBLE BOARD * 15 3-054-937-01 SPRING, BT RELEASE 6 3-914-366-01 SCREW (DIA. 1.7x4), PRECISION * 16 3-057-099-01 SHEET, BB FIXED 7 3-056-741-01 COVER, AC 17 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 8 3-056-740-01 LID, BATTERY 18 3-057-094-01 SHEET, HI 9 3-050-594-01 SPRING, COMPRESSION BT901 1-694-531-11 TERMINAL BOARD, BATTERY 10 3-056-744-01 KNOB, LOCK 6-1, 6-1-2. FRONT CABINET ASSEMBLY 68 68 not supplied not supplied 68 52 68 56 not supplied not supplied not supplied A not supplied 66 not supplied not supplied not supplied 53 not supplied 68 MIC901 67 70not supplied 68 not supplied not supplied 64 not supplied 54 not 73 not supplied supplied 59 not supplied not

A supplied

64 64 65 62 65 not supplied 70 not supplied 6571 51 65 58 (NOTE) 69 NOTE : Refer to page 2-5 "2-7. Removal of upper cabinet block and flash The components identified by Les composants identifiés par une unit (MC)" for datails of replacement of Flash unit (MC). mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified. piéce portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3949-843-1 CABINET (F) ASSY, P * 63 3-058-170-01 SHEET, MICROPHONE 52 X-3949-844-1 HINGE ASSY 64 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 53 X-3949-907-1 GRILLE ASSY, MICROPHONE 65 3-713-791-01 SCREW (M1.7x4), TAPPING, P2 54 X-3949-846-1 CABINET (UPPER) ASSY 55 X-3949-849-1 RETAINER ASSY, JK 66 3-713-786-21 SCREW (M2x3) 67 3-948-339-61 TAPPING 56 X-3949-906-1 CABINET (M) ASSY 68 3-719-381-01 SCREW (M2x4) 57 3-054-954-01 CUSHION, MICROPHONE 69 1-960-050-11 HARNESS (MS-114) !58 1-418-657-11 FLASH UNIT (MC) 70 1-960-061-11 HARNESS (GN-52) * 59 3-056-769-01 GUARD, FP 60 3-056-716-01 COVER, HOOK 71 3-914-366-01 SCREW (DIA. 1.7x4), PRECISION 72 1-675-590-11 FP-133 FLEXIBLE BOARD * 61 3-056-765-01 HOLDER, FP 73 X-3949-914-1 COVER ASSY, JK (SERVICE) 62 1-418-653-11 SWITCH BLOCK, CONTROL (PW) MIC901 1-542-408-11 MICROPHONE UNIT 6-2, 6-1-3. REAR CABINET ASSEMBLY not supplied 110 105 not supplied 118 109 104 117 112 SP901 103 111 114 107 108 LCD901 119 113 115 114 ND901 115 122 101 115 121 102 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified. piéce portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 1-418-237-21 TRANSFORMER UNIT, INVERTER 114 3-914-366-01 SCREW (DIA. 1.7x4), PRECISION 102 1-675-591-21 FP-134 FLEXIBLE BOARD 115 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 103 1-418-654-11 SWITCH BLOCK, CONTROL (FK) * 104 3-057-098-01 SHEET, SP PROTECTION 116 3-056-711-01 SCREW (M1.4) * 105 3-057-088-01 RETAINER (SP) 117 7-624-106-04 STOP RING 3.0, TYPE -E 118 1-960-060-11 HARNESS (SP-163) 106 3-058-280-01 BUTTON, FUNCTION 119 1-960-049-11 HARNESS (HB-50) 107 3-056-771-01 BUTTON, BR 120 3-056-773-01 SHEET, BL LIGHT INTERCEPTION 108 3-056-770-01 KNOB, BL 109 3-056-707-01 BRACKET, STRAP * 121 3-056-772-01 SHEET, BL INSULATING 110 X-3949-872-1 LEVER ASSY, ZOOM * 122 3-057-534-01 SHEET, PANEL SHIELD LCD901 1-803-549-22 MODULE, CRYSTAL INDICATION (LQ20A8FR20) 111 X-3949-873-1 ESCUTCHEON (R) ASSY !ND901 1-517-878-21 TUBE, FLUORESCENT,COLD CATHODE 112 X-3949-841-1 CABINET (R) ASSY, P SP901 1-505-862-11 SPEAKER (2.0CM) 113 3-056-774-01 CUSHION, BL 6-3, 6-1-4. LENS CABINET ASSEMBLY not supplied 156 153 not supplied not supplied not supplied 167160 not supplied 166 164 not supplied not supplied 169 159 Lens assembly (See page 6-5) 164 166 164 165 152 165 165 165 not supplied 164 168 not supplied 165 164 168 not supplied 162 171 not supplied 161 170 165 151 155 165 The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified. piéce portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 X-3949-837-1 CABINET (MF) ASSY 161 1-418-652-11 SWITCH BLOCK, CONTROL (CF) 152 X-3949-839-1 SHEET METAL ASSY, ST 162 3-056-700-01 PLATE, TRIPOD 153 X-3949-838-1 CABINET (LT) ASSY 163 3-056-763-01 ORNAMENT, LENS 154 X-3949-840-1 CABINET (LB) ASSY 164 3-713-791-01 SCREW (M1.7x4), TAPPING, P2 155 1-418-656-11 FOCUS BLOCK, MANUAL 165 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 !156 1-418-658-11 FLASH UNIT (ST) 166 4-984-006-01 SCREW, STEP 157 1-675-593-11 FP-136 FLEXIBLE BOARD 167 3-054-938-01 SCREW, STEP 158 3-056-688-01 COVER, RELEASE 168 3-713-786-21 SCREW (M2x3) 159 3-056-690-01 SPRING (R), COMPRESSION COIL 169 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 160 3-056-689-01 KNOB, RELEASE 170 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION * 171 3-058-265-01 SHEET, SH COPY 6-4, 6-1-5. LENS ASSEMBLY 209 213 not supplied not supplied not supplied IC101 213 M901 not supplied

A

not supplied M902 212 211 not suppliedA 212 211 202 203 212 212 Be sure to read “Note on the CCD Imager replacement” on page 4–10 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 201 A-7074-098-A LD-98 BOARD, COMPLETE 211 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 202 A-7094-686-A SY-56 BOARD, COMPLETE (SERVICE) 212 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 203 A-7074-097-A PS-427 BOARD, COMPLETE 213 3-318-203-11 SCREW (B1.7x6), TAPPING 204 1-675-592-11 FP-135 FLEXIBLE BOARD * 205 3-056-756-01 FRAME, LENS IC101 A-7030-987-A CCD BLOCK ASSY (CCD IMAGER) M901 3-709-551-01 MOTOR UNIT, ZOOM STEPPING 206 3-054-554-11 ADAPTOR (K), CCD FITTING M902 3-709-400-01 MOTOR, FOCUS STEPPING 207 1-758-319-21 FILTER BLOCK, OPTICAL 208 3-054-555-11 RUBBER (K), SEAL 209 A-7074-096-A CD-236 BOARD, COMPLETE 210 A-7031-036-A LENS ASSY 6-5,

CD-236

6-2. ELECTRICAL PARTS LIST Note: The components identified by • Due to standardization, replacements in the parts list • SEMICONDUCTORS mark ! or dotted line with mark may be different from the parts specified in the In each case, u: µ , for example: ! are critical for safety. diagrams or the components used on the set. uA...: µ A..., uPA...: µ PA..., uPB...: µ PB..., Replace only with part number • -XX, -X mean standardized parts, so they may have uPC...: µ PC..., uPD...: µ PD... specified. some difference from the original one. • CAPACITORS • Items marked “*” are not stocked since they are uF : µ F Les composants identifiés par une seldom required for routine service. Some delay • COILS marque ! sont critiques pour la should be anticipated when ordering these items. uH : µ H sécurité. • RESISTORS • Abbreviation Ne les remplacer que par une All resistors are in ohms CND : Canadian model piéce portant le numéro spécifié. METAL: Metal-film resistor HK : Hong Kong model METAL OXIDE: Metal Oxide-film resistor AUS : Australian model When indicating parts by reference F : nonflammable JE : Tourist model number, please include the board CH : Chinese model name. KR : Korea model J : Japanese model Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-096-A CD-236 BOARD, COMPLETE < CONNECTOR > ********************* (Ref.No. : 3000 Series) CN101 1-785-496-21 CONNECTOR, FFC/FPC (ZIF) 39P (IC101 is not included in this complete board.) < FERRITE BEAD > < CAPACITOR > FB101 1-414-228-11 INDUCTOR CHIP 0UH C102 1-164-850-11 CERAMIC CHIP 10PF 0.5PF 16V FB103 1-414-228-11 INDUCTOR CHIP 0UH C103 1-107-820-11 CERAMIC CHIP 0.1uF 16V * FB104 1-500-282-11 INDUCTOR CHIP 0UH C104 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V * FB105 1-500-282-11 INDUCTOR CHIP 0UH C105 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V FB106 1-414-228-11 INDUCTOR CHIP 0UH C106 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V FB107 1-414-228-11 INDUCTOR CHIP 0UH C107 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V FB108 1-414-228-11 INDUCTOR CHIP 0UH C108 1-119-751-11 TANTAL. CHIP 22uF 20% 16V FB109 1-216-864-11 METAL CHIP 0 5% 1/16W C109 1-113-985-11 TANTAL. CHIP 10uF 20% 20V (Note) C110 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V FB110 1-216-864-11 METAL CHIP 0 5% 1/16W C111 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V (Note) FB111 1-216-864-11 METAL CHIP 0 5% 1/16W C112 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V (Note) C113 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C114 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V < IC > C115 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C116 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V IC101 A-7030-987-A CCD BLOCK ASSY (CCD IMAGER) IC102 8-752-397-43 IC CXD2470R-T4 C117 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V IC103 8-759-646-91 IC CCD1000Y-2/2K C118 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C119 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < COIL > C120 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C121 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V L101 1-469-528-91 INDUCTOR 100uH L102 1-469-525-91 INDUCTOR 10uH C122 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V L103 1-469-525-91 INDUCTOR 10uH C123 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C124 1-109-982-11 CERAMIC CHIP 1uF 10% 10V < TRANSISTOR > C125 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C126 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q101 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1 Q102 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C127 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q103 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C128 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C129 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < RESISTOR > C130 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C131 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R101 1-218-959-11 RES,CHIP 3.3K 5% 1/16W R102 1-218-989-11 RES,CHIP 1M 5% 1/16W C132 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V R103 1-218-961-11 RES,CHIP 4.7K 5% 1/16W C133 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V R104 1-218-933-11 RES,CHIP 22 5% 1/16W C134 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R105 1-218-933-11 RES,CHIP 22 5% 1/16W C135 1-113-985-11 TANTAL. CHIP 10uF 20% 20V C136 1-107-820-11 CERAMIC CHIP 0.1uF 16V R106 1-218-990-11 SHORT 0 R108 1-218-990-11 SHORT 0 C137 1-107-820-11 CERAMIC CHIP 0.1uF 16V R109 1-218-973-11 RES,CHIP 47K 5% 1/16W C138 1-119-751-11 TANTAL. CHIP 22uF 20% 16V Be sure to read “Precautions upon replacing CCD imager” Note : Resistors are mounted to the location where FB109, FB110, on page 4-10 when changing the CCD imager. 6-6 FB111, are printed.,

CD-236 DD-131

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R110 1-218-933-11 RES,CHIP 22 5% 1/16W C039 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R111 1-218-937-11 RES,CHIP 47 5% 1/16W C040 1-109-982-11 CERAMIC CHIP 1uF 10% 10V C041 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R113 1-218-977-11 RES,CHIP 100K 5% 1/16W C042 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V R114 1-218-937-11 RES,CHIP 47 5% 1/16W C043 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V R115 1-218-937-11 RES,CHIP 47 5% 1/16W R116 1-218-937-11 RES,CHIP 47 5% 1/16W C044 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V R117 1-218-937-11 RES,CHIP 47 5% 1/16W C045 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C048 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V R118 1-218-937-11 RES,CHIP 47 5% 1/16W C049 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V R119 1-218-937-11 RES,CHIP 47 5% 1/16W C050 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R120 1-218-937-11 RES,CHIP 47 5% 1/16W R121 1-218-937-11 RES,CHIP 47 5% 1/16W C051 1-109-982-11 CERAMIC CHIP 1uF 10% 10V R122 1-218-937-11 RES,CHIP 47 5% 1/16W C052 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C053 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V R123 1-218-937-11 RES,CHIP 47 5% 1/16W C054 1-113-987-11 TANTAL. CHIP 4.7uF 20% 25V R124 1-216-864-11 METAL CHIP 0 5% 1/16W C056 1-109-982-11 CERAMIC CHIP 1uF 10% 10V < VIBRATOR > C057 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V C058 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V X101 1-781-457-21 OSCILLATOR, CRYSTAL (24.375MHz) C059 1-113-987-11 TANTAL. CHIP 4.7uF 20% 25V X102 1-781-456-21 OSCILLATOR, CRYSTAL (24.54MHz) C060 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C061 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V < CONNECTOR > A-7074-101-A DD-131 BOARD, COMPLETE ********************* CN001 1-774-730-21 PIN, CONNECTOR (PC BOARD) 3P (Ref.No. : 2000 Series) CN002 1-770-621-21 PIN, CONNECTOR 4P CN003 1-785-917-21 CONNECTOR, BOARD TO BOARD 40P < CAPACITOR > < DIODE > C001 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C002 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V D001 8-719-074-08 DIODE MA4ZD03001S0 C003 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V D002 8-719-075-12 DIODE MA3XD21001S0 C004 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D003 8-719-071-34 DIODE RB521S-30-TE61 C005 1-162-979-11 CERAMIC CHIP 0.0027uF 10% 50V D004 8-719-074-08 DIODE MA4ZD03001S0 D005 8-719-074-08 DIODE MA4ZD03001S0 C006 1-164-874-11 CERAMIC CHIP 100PF 5% 16V C007 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D006 8-719-074-08 DIODE MA4ZD03001S0 C008 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D007 8-719-074-08 DIODE MA4ZD03001S0 C009 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V C010 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V < IC > C011 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V IC001 8-759-581-99 IC MB3827PFV-G-BND-ER C012 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V IC002 8-759-486-48 IC XC6372C351PR C013 1-164-876-11 CERAMIC CHIP 120PF 5% 16V C014 1-164-874-11 CERAMIC CHIP 100PF 5% 16V < COIL > C015 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V L001 1-416-510-11 INDUCTOR 100uH C016 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L002 1-419-353-11 INDUCTOR 10uH C017 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V L003 1-419-354-11 INDUCTOR 22uH C018 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L004 1-419-354-11 INDUCTOR 22uH C019 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L005 1-419-354-11 INDUCTOR 22uH C022 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V L006 1-414-392-21 INDUCTOR 1uH C023 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L007 1-414-392-21 INDUCTOR 1uH C024 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V L008 1-414-428-21 INDUCTOR 1uH C025 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L009 1-469-524-91 INDUCTOR 4.7uH C026 1-109-982-11 CERAMIC CHIP 1uF 10% 10V L010 1-469-527-91 INDUCTOR 47uH C027 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V L011 1-414-392-21 INDUCTOR 1uH C028 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L012 1-469-528-91 INDUCTOR 100uH C029 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V L013 1-469-528-91 INDUCTOR 100uH C030 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V L014 1-414-392-21 INDUCTOR 1uH C032 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L015 1-469-527-91 INDUCTOR 47uH C033 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L016 1-469-528-91 INDUCTOR 100uH C034 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C035 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V < LINE FILTER > C036 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C037 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V LF001 1-411-957-11 FILTER, COMMON MODE C038 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V 6-7,

DD-131

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC LINK > R028 1-218-972-11 RES,CHIP 39K 5% 1/16W R029 1-218-970-11 RES,CHIP 27K 5% 1/16W !PS001 1-533-761-21 LINK, IC (SMD) 1.4A R030 1-208-711-11 METAL CHIP 15K 0.50% 1/16W !PS002 1-533-761-21 LINK, IC (SMD) 1.4A R031 1-218-973-11 RES,CHIP 47K 5% 1/16W !PS003 1-533-761-21 LINK, IC (SMD) 1.4A R032 1-218-965-11 RES,CHIP 10K 5% 1/16W !PS004 1-533-761-21 LINK, IC (SMD) 1.4A R033 1-218-968-11 RES,CHIP 18K 5% 1/16W < TRANSISTOR > R034 1-208-701-11 METAL CHIP 5.6K 0.50% 1/16W R035 1-208-721-11 METAL CHIP 39K 0.50% 1/16W Q003 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO R036 1-208-713-11 METAL CHIP 18K 0.50% 1/16W Q004 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO R037 1-208-931-11 METAL CHIP 68K 0.50% 1/16W Q005 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q006 8-729-162-13 TRANSISTOR 2SC1621-T1B3 R038 1-208-719-11 METAL CHIP 33K 0.50% 1/16W Q007 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO R039 1-208-707-11 METAL CHIP 10K 0.50% 1/16W R040 1-218-953-11 RES,CHIP 1K 5% 1/16W Q008 8-729-162-13 TRANSISTOR 2SC1621-T1B3 R041 1-208-701-11 METAL CHIP 5.6K 0.50% 1/16W Q009 8-729-043-94 TRANSISTOR CPH3106-PM-TL R042 1-208-709-11 METAL CHIP 12K 0.50% 1/16W Q010 8-729-043-94 TRANSISTOR CPH3106-PM-TL Q011 8-729-049-11 TRANSISTOR CPH3206-TL R043 1-208-711-11 METAL CHIP 15K 0.50% 1/16W Q012 8-729-047-74 TRANSISTOR CPH5701-TL R044 1-218-966-11 RES,CHIP 12K 5% 1/16W R045 1-218-970-11 RES,CHIP 27K 5% 1/16W Q013 8-729-047-74 TRANSISTOR CPH5701-TL R046 1-218-990-11 SHORT 0 Q014 8-729-047-68 TRANSISTOR 2SK1830-TE85L R047 1-208-711-11 METAL CHIP 15K 0.50% 1/16W Q015 8-729-048-19 TRANSISTOR CPH5704-TL Q016 8-729-046-00 TRANSISTOR CPH6301-TL R049 1-218-957-11 RES,CHIP 2.2K 5% 1/16W Q017 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R050 1-208-910-11 METAL CHIP 9.1K 0.50% 1/16W R051 1-208-711-11 METAL CHIP 15K 0.50% 1/16W Q019 8-729-044-84 TRANSISTOR CPH3403-TL R052 1-218-970-11 RES,CHIP 27K 5% 1/16W Q020 8-729-044-84 TRANSISTOR CPH3403-TL R053 1-218-968-11 RES,CHIP 18K 5% 1/16W Q021 8-729-048-19 TRANSISTOR CPH5704-TL Q022 8-729-048-19 TRANSISTOR CPH5704-TL R054 1-218-945-11 RES,CHIP 220 5% 1/16W Q023 8-729-048-18 TRANSISTOR CPH5601-TL R055 1-218-952-11 RES,CHIP 820 5% 1/16W R056 1-218-951-11 RES,CHIP 680 5% 1/16W Q024 8-729-427-46 TRANSISTOR XP4213-TXE R057 1-218-956-11 RES,CHIP 1.8K 5% 1/16W Q025 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R058 1-218-962-11 RES,CHIP 5.6K 5% 1/16W Q030 8-729-037-71 TRANSISTOR UN9210J-(K8).SO Q031 8-729-042-57 TRANSISTOR UN9110J-(K8).SO R059 1-218-959-11 RES,CHIP 3.3K 5% 1/16W Q032 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R060 1-218-965-11 RES,CHIP 10K 5% 1/16W R061 1-218-965-11 RES,CHIP 10K 5% 1/16W Q033 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO R062 1-218-945-11 RES,CHIP 220 5% 1/16W R063 1-218-945-11 RES,CHIP 220 5% 1/16W < RESISTOR > R064 1-218-985-11 RES,CHIP 470K 5% 1/16W R001 1-208-939-11 METAL CHIP 150K 0.50% 1/16W R065 1-218-971-11 RES,CHIP 33K 5% 1/16W R002 1-208-721-11 METAL CHIP 39K 0.50% 1/16W R066 1-218-971-11 RES,CHIP 33K 5% 1/16W R003 1-218-977-11 RES,CHIP 100K 5% 1/16W R067 1-218-973-11 RES,CHIP 47K 5% 1/16W R004 1-208-711-11 METAL CHIP 15K 0.50% 1/16W R068 1-218-965-11 RES,CHIP 10K 5% 1/16W R005 1-208-711-11 METAL CHIP 15K 0.50% 1/16W R069 1-218-965-11 RES,CHIP 10K 5% 1/16W R006 1-208-699-11 METAL CHIP 4.7K 0.50% 1/16W R070 1-218-977-11 RES,CHIP 100K 5% 1/16W R007 1-208-711-11 METAL CHIP 15K 0.50% 1/16W R071 1-218-970-11 RES,CHIP 27K 5% 1/16W R008 1-218-970-11 RES,CHIP 27K 5% 1/16W R072 1-218-968-11 RES,CHIP 18K 5% 1/16W R010 1-218-963-11 RES,CHIP 6.8K 5% 1/16W R073 1-218-965-11 RES,CHIP 10K 5% 1/16W R011 1-218-973-11 RES,CHIP 47K 5% 1/16W R074 1-218-977-11 RES,CHIP 100K 5% 1/16W R012 1-208-719-11 METAL CHIP 33K 0.50% 1/16W R075 1-216-295-91 SHORT 0 R013 1-208-715-11 METAL CHIP 22K 0.50% 1/16W R076 1-218-990-11 SHORT 0 R014 1-218-970-11 RES,CHIP 27K 5% 1/16W R077 1-218-977-11 RES,CHIP 100K 5% 1/16W R015 1-218-973-11 RES,CHIP 47K 5% 1/16W R078 1-218-973-11 RES,CHIP 47K 5% 1/16W R016 1-218-973-11 RES,CHIP 47K 5% 1/16W R079 1-218-959-11 RES,CHIP 3.3K 5% 1/16W R017 1-218-970-11 RES,CHIP 27K 5% 1/16W R018 1-218-969-11 RES,CHIP 22K 5% 1/16W < TRANSFORMER > R020 1-208-927-11 METAL CHIP 47K 0.50% 1/16W R021 1-218-970-11 METAL CHIP 27K 0.50% 1/16W !T001 1-433-784-21 TRANSFORMER, DC-DC CONVERTER R022 1-218-968-11 RES,CHIP 18K 5% 1/16W !T002 1-433-786-21 TRANSFORMER, DC-DC CONVERTER !T003 1-433-785-21 TRANSFORMER, DC-DC CONVERTER R023 1-218-970-11 RES,CHIP 27K 5% 1/16W R024 1-218-990-11 SHORT 0 R025 1-218-969-11 RES,CHIP 22K 5% 1/16W R026 1-218-981-11 RES,CHIP 220K 5% 1/16W The components identified by Les composants identifiés par une R027 1-218-969-11 RES,CHIP 22K 5% 1/16W mark ! or dotted line with mark marque ! sont critiques pour la! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une 6-8 specified. piéce portant le numéro spécifié.,

HI-70

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-685-A HI-70 BOARD, COMPLETE (SERVICE) C739 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V ******************** C740 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V (Ref.No. : 2000 Series) C741 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V < BATTERY > C743 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C744 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V * BT601 1-528-900-11 BATTERY, LITHIUM SECONDARY C745 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C801 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CAPACITOR > C802 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C301 1-113-682-11 TANTAL. CHIP 33uF 20% 10V C803 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C302 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C804 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C303 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C805 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C304 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C806 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C306 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V C807 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V C307 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C808 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C308 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C810 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C309 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C811 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C310 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C812 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C311 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C813 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C313 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C814 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C315 1-104-847-11 TANTAL. CHIP 22uF 20% 4V C815 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C316 1-104-848-11 TANTAL. CHIP 100uF 20% 4V C816 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C605 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C817 1-135-149-21 TANTALUM CHIP 2.2uF 20% 10V C606 1-104-912-11 TANTAL. CHIP 3.3uF 20% 16V C902 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V C608 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V C903 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C609 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C904 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C610 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C905 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C611 1-164-858-11 CERAMIC CHIP 22PF 5% 16V C906 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C612 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C907 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C613 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C908 1-164-872-11 CERAMIC CHIP 82PF 5% 16V C615 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C909 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C616 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C911 1-164-739-11 CERAMIC CHIP 560PF 5% 50V C620 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C913 1-164-872-11 CERAMIC CHIP 82PF 5% 16V C622 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C915 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C623 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C916 1-113-994-11 TANTAL. CHIP 6.8uF 20% 16V C624 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C917 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C629 1-113-682-11 TANTAL. CHIP 33uF 20% 10V C918 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C633 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C919 1-107-689-21 TANTAL. CHIP 1uF 20% 35V C701 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C920 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C702 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C927 1-164-676-11 CERAMIC CHIP 2200PF 5% 16V C703 1-216-864-11 METAL CHIP 0 5% 1/16W C704 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < CONNECTOR > C711 1-125-926-91 TANTAL. CHIP 4.7uF 20% 6.3V C712 1-135-337-11 TANTAL. CHIP 1uF 20% 6.3V CN601 1-778-803-11 CONNECTOR, BOARD TO BOARD 40P CN602 1-784-423-21 CONNECTOR, FFC/FPC (ZIF) 39P C713 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V CN603 1-784-422-11 CONNECTOR, FFC/FPC (ZIF) 33P C714 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V CN604 1-784-420-11 CONNECTOR, FFC/FPC (ZIF) 21P C715 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V CN605 1-793-302-21 PIN, CONNECTOR (PC BOARD) 5P C717 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V C721 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V CN606 1-793-641-11 CONNECTOR, MEMORY STICK CN607 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P C724 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V * CN701 1-770-619-11 PIN, CONNECTOR 2P C725 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V CN702 1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P C726 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V CN901 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P C727 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C728 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V < DIODE > C729 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V D602 8-719-056-48 DIODE 1SS388(TPL3) C730 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V D604 8-719-056-48 DIODE 1SS388(TPL3) C731 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V D606 8-719-056-23 DIODE 1SS387-TPL3 C732 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V D607 8-719-058-12 DIODE CL-220UR-C-TS C733 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V D608 8-719-056-61 DIODE MAZS082008SO C734 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V D903 8-713-102-80 DIODE 1T369-01-T8A C735 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V D904 8-719-976-96 DIODE MA8047-H-TX 6-9,

HI-70

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < FERRITE BEAD > < RESISTOR > FB605 1-500-284-21 INDUCTOR CHIP 0UH R303 1-218-989-11 RES,CHIP 1M 5% 1/16W FB606 1-500-284-21 INDUCTOR CHIP 0UH R304 1-218-953-11 RES,CHIP 1K 5% 1/16W FB607 1-500-284-21 INDUCTOR CHIP 0UH R307 1-218-939-11 RES,CHIP 68 5% 1/16W FB701 1-414-228-11 INDUCTOR CHIP 0UH R312 1-218-969-11 RES,CHIP 22K 5% 1/16W FB901 1-414-594-11 INDUCTOR CHIP 0UH R604 1-218-985-11 RES,CHIP 470K 5% 1/16W < IC > R605 1-218-977-11 RES,CHIP 100K 5% 1/16W R606 1-218-942-11 RES,CHIP 120 5% 1/16W IC301 8-759-582-18 IC NJM2538BV(TE2) R607 1-218-990-11 SHORT 0 IC601 8-759-525-51 IC S-80827HNNP-A9A-T2 R608 1-218-951-11 RES,CHIP 680 5% 1/16W IC602 8-759-538-14 IC S-3513BEFS-TB R609 1-218-985-11 RES,CHIP 470K 5% 1/16W IC603 8-759-639-65 IC S579615PZ-TEB IC605 8-759-525-53 IC RN5RZ31BA-TL R610 1-218-961-11 RES,CHIP 4.7K 5% 1/16W R611 1-218-965-11 RES,CHIP 10K 5% 1/16W IC606 8-759-466-71 IC S-80820ANNP-EDH-T2 R613 1-218-977-11 RES,CHIP 100K 5% 1/16W IC607 8-759-566-20 IC AK6440BH-E2 R614 1-218-985-11 RES,CHIP 470K 5% 1/16W IC702 8-759-582-00 IC AN2904FHQ-EB R615 1-218-985-11 RES,CHIP 470K 5% 1/16W IC801 8-759-530-19 IC MB40D001PFV-G-BND-ER IC802 8-759-539-27 IC IR3Y37A4 R616 1-218-977-11 RES,CHIP 100K 5% 1/16W R617 1-218-977-11 RES,CHIP 100K 5% 1/16W IC803 8-759-196-97 IC TC7SH32FU-TE85R R618 1-218-985-11 RES,CHIP 470K 5% 1/16W IC901 8-759-587-61 IC LZ9GH234 R619 1-218-977-11 RES,CHIP 100K 5% 1/16W IC902 8-759-327-01 IC NJM062V(TE2) R620 1-218-977-11 RES,CHIP 100K 5% 1/16W < COIL > R621 1-218-977-11 RES,CHIP 100K 5% 1/16W R622 1-218-958-11 RES,CHIP 2.7K 5% 1/16W L301 1-469-527-91 INDUCTOR 47uH R624 1-218-953-11 RES,CHIP 1K 5% 1/16W L302 1-469-525-91 INDUCTOR 10uH R625 1-218-977-11 RES,CHIP 100K 5% 1/16W L601 1-469-525-91 INDUCTOR 10uH R626 1-218-973-11 RES,CHIP 47K 5% 1/16W L701 1-469-525-91 INDUCTOR 10uH L704 1-469-525-91 INDUCTOR 10uH R627 1-218-985-11 RES,CHIP 470K 5% 1/16W R628 1-218-985-11 RES,CHIP 470K 5% 1/16W L706 1-469-525-91 INDUCTOR 10uH R630 1-218-989-11 RES,CHIP 1M 5% 1/16W L801 1-469-528-91 INDUCTOR 100uH R633 1-218-977-11 RES,CHIP 100K 5% 1/16W L802 1-469-525-91 INDUCTOR 10uH R634 1-218-977-11 RES,CHIP 100K 5% 1/16W L901 1-469-525-91 INDUCTOR 10uH L902 1-469-525-91 INDUCTOR 10uH R635 1-218-965-11 RES,CHIP 10K 5% 1/16W R636 1-218-953-11 RES,CHIP 1K 5% 1/16W L903 1-469-525-91 INDUCTOR 10uH R639 1-218-985-11 RES,CHIP 470K 5% 1/16W L905 1-412-949-21 INDUCTOR 6.8uH R641 1-218-965-11 RES,CHIP 10K 5% 1/16W R642 1-218-953-11 RES,CHIP 1K 5% 1/16W < TRANSISTOR > R643 1-218-929-11 RES,CHIP 10 5% 1/16W Q302 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R644 1-218-965-11 RES,CHIP 10K 5% 1/16W Q303 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R645 1-218-953-11 RES,CHIP 1K 5% 1/16W Q604 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R646 1-218-965-11 RES,CHIP 10K 5% 1/16W Q605 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R647 1-218-953-11 RES,CHIP 1K 5% 1/16W Q607 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R648 1-218-989-11 RES,CHIP 1M 5% 1/16W Q608 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R649 1-218-973-11 RES,CHIP 47K 5% 1/16W Q609 8-729-041-43 TRANSISTOR HN1L02FU(TE85R) R650 1-218-989-11 RES,CHIP 1M 5% 1/16W Q610 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R651 1-218-953-11 RES,CHIP 1K 5% 1/16W Q611 8-729-427-16 TRANSISTOR XP4113-TXE R653 1-218-977-11 RES,CHIP 100K 5% 1/16W Q612 8-729-427-46 TRANSISTOR XP4213-TXE R654 1-208-947-11 METAL CHIP 330K 0.50% 1/16W Q701 8-729-042-74 TRANSISTOR UN9216J-(K8).SO R656 1-218-989-11 METAL CHIP 1M 0.50% 1/16W Q702 8-729-037-61 TRANSISTOR UN9113J-(K8).SO R657 1-218-953-11 RES,CHIP 1K 5% 1/16W Q704 8-729-041-51 TRANSISTOR FMMT617TA R658 1-218-953-11 RES,CHIP 1K 5% 1/16W Q705 8-729-230-60 TRANSISTOR 2SA1586YG-TE85L R659 1-218-953-11 RES,CHIP 1K 5% 1/16W Q706 8-729-037-76 TRANSISTOR UN9215J-(K8).SO R660 1-218-953-11 RES,CHIP 1K 5% 1/16W Q903 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX R661 1-218-965-11 RES,CHIP 10K 5% 1/16W Q904 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R662 1-218-965-11 RES,CHIP 10K 5% 1/16W Q905 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX R663 1-218-946-11 RES,CHIP 270 5% 1/16W Q906 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R667 1-218-977-11 RES,CHIP 100K 5% 1/16W R668 1-218-985-11 RES,CHIP 470K 5% 1/16W R669 1-218-977-11 RES,CHIP 100K 5% 1/16W R670 1-218-990-11 SHORT 0 6-10,

HI-70 LD-98

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R671 1-218-953-11 RES,CHIP 1K 5% 1/16W R932 1-218-977-11 RES,CHIP 100K 5% 1/16W R672 1-218-953-11 RES,CHIP 1K 5% 1/16W R933 1-218-977-11 RES,CHIP 100K 5% 1/16W R934 1-218-990-11 SHORT 0 R673 1-218-953-11 RES,CHIP 1K 5% 1/16W R674 1-218-985-11 RES,CHIP 470K 5% 1/16W R935 1-218-990-11 SHORT 0 R675 1-218-990-11 SHORT 0 R938 1-218-977-11 RES,CHIP 100K 5% 1/16W R678 1-218-973-11 RES,CHIP 47K 5% 1/16W R939 1-218-971-11 RES,CHIP 33K 5% 1/16W R680 1-218-990-11 SHORT 0 R941 1-208-719-11 METAL CHIP 33K 0.50% 1/16W R942 1-208-715-11 METAL CHIP 22K 0.50% 1/16W R681 1-218-990-11 SHORT 0 R682 1-218-957-11 RES,CHIP 2.2K 5% 1/16W R943 1-208-719-11 METAL CHIP 33K 0.50% 1/16W R701 1-218-849-11 METAL CHIP 3.3K 0.50% 1/16W R944 1-208-715-11 METAL CHIP 22K 0.50% 1/16W R702 1-218-849-11 METAL CHIP 3.3K 0.50% 1/16W R967 1-218-937-11 RES,CHIP 47 5% 1/16W R704 1-218-990-11 SHORT 0 R968 1-218-937-11 RES,CHIP 47 5% 1/16W R969 1-218-937-11 RES,CHIP 47 5% 1/16W R705 1-218-957-11 RES,CHIP 2.2K 5% 1/16W R707 1-218-970-11 METAL CHIP 27K 0.50% 1/16W R978 1-218-973-11 RES,CHIP 47K 5% 1/16W R708 1-218-973-11 RES,CHIP 47K 5% 1/16W R979 1-218-973-11 RES,CHIP 47K 5% 1/16W R709 1-218-974-11 METAL CHIP 56K 0.50% 1/16W R980 1-208-931-11 METAL CHIP 68K 0.50% 1/16W R712 1-218-957-11 RES,CHIP 2.2K 5% 1/16W R981 1-218-961-11 RES,CHIP 4.7K 5% 1/16W R713 1-218-977-11 RES,CHIP 100K 5% 1/16W < VIBRATOR > R714 1-218-975-11 RES,CHIP 68K 5% 1/16W R715 1-218-957-11 RES,CHIP 2.2K 5% 1/16W X601 1-767-980-21 VIBRATOR, CERAMIC (20MHz) R717 1-218-969-11 RES,CHIP 22K 5% 1/16W X602 1-760-458-21 VIBRATOR, CRYSTAL (32.768kHz) R718 1-218-957-11 RES,CHIP 2.2K 5% 1/16W R719 1-218-973-11 RES,CHIP 47K 5% 1/16W R720 1-218-941-11 RES,CHIP 100 5% 1/16W A-7074-098-A LD-98 BOARD, COMPLETE R721 1-218-949-11 RES,CHIP 470 5% 1/16W ******************** R723 1-218-990-11 SHORT 0 (Ref.No. : 4000 Series) R725 1-218-953-11 RES,CHIP 1K 5% 1/16W < CAPACITOR > R726 1-218-954-11 RES,CHIP 1.2K 5% 1/16W R727 1-218-990-11 SHORT 0 C401 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R728 1-218-990-11 SHORT 0 C402 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R729 1-208-711-11 METAL CHIP 15K 0.50% 1/16W C403 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R733 1-216-864-11 METAL CHIP 0 5% 1/16W C404 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C405 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R801 1-218-990-11 SHORT 0 R804 1-218-969-11 RES,CHIP 22K 5% 1/16W C406 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V R805 1-218-966-11 RES,CHIP 12K 5% 1/16W C407 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R806 1-218-973-11 RES,CHIP 47K 5% 1/16W C408 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R812 1-218-977-11 RES,CHIP 100K 5% 1/16W C409 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V C410 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V R817 1-218-965-11 RES,CHIP 10K 5% 1/16W R821 1-218-990-11 SHORT 0 C411 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R822 1-218-972-11 RES,CHIP 39K 5% 1/16W C412 1-113-682-11 TANTAL. CHIP 33uF 20% 10V R823 1-218-966-11 RES,CHIP 12K 5% 1/16W C413 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R824 1-218-980-11 RES,CHIP 180K 5% 1/16W C414 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C415 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R827 1-218-967-11 RES,CHIP 15K 5% 1/16W R828 1-218-971-11 RES,CHIP 33K 5% 1/16W C416 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V R905 1-218-987-11 RES,CHIP 680K 5% 1/16W C418 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R908 1-218-978-11 RES,CHIP 120K 5% 1/16W C419 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R912 1-218-977-11 RES,CHIP 100K 5% 1/16W C420 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C421 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R913 1-218-965-11 RES,CHIP 10K 5% 1/16W R914 1-218-989-11 RES,CHIP 1M 5% 1/16W C422 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V R915 1-218-989-11 RES,CHIP 1M 5% 1/16W C423 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R916 1-218-969-11 RES,CHIP 22K 5% 1/16W C424 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V R918 1-218-975-11 RES,CHIP 68K 5% 1/16W C425 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C426 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R920 1-208-931-11 METAL CHIP 68K 0.50% 1/16W R921 1-218-975-11 RES,CHIP 68K 5% 1/16W < CONNECTOR > R922 1-218-973-11 RES,CHIP 47K 5% 1/16W R924 1-208-719-11 METAL CHIP 33K 0.50% 1/16W CN401 1-784-421-11 CONNECTOR, FFC/FPC (ZIF) 27P R926 1-218-961-11 RES,CHIP 4.7K 5% 1/16W CN402 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P R929 1-218-977-11 RES,CHIP 100K 5% 1/16W R930 1-218-971-11 RES,CHIP 33K 5% 1/16W 6-11,

LD-98 PS-427

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < DIODE > R433 1-218-973-11 RES,CHIP 47K 5% 1/16W R434 1-218-975-11 RES,CHIP 68K 5% 1/16W D401 8-719-067-36 DIODE MA3ZD1200LS0 R435 1-218-975-11 RES,CHIP 68K 5% 1/16W D402 8-719-073-01 DIODE MA111-(K8).S0 R436 1-218-957-11 RES,CHIP 2.2K 5% 1/16W R437 1-218-957-11 RES,CHIP 2.2K 5% 1/16W < IC > R438 1-218-929-11 RES,CHIP 10 5% 1/16W IC401 8-759-337-40 IC NJM2904V(TE2) R439 1-218-959-11 RES,CHIP 3.3K 5% 1/16W IC402 8-759-579-97 IC uPD16833AGS-9JH IC403 8-759-579-97 IC uPD16833AGS-9JH IC404 8-759-337-40 IC NJM2904V(TE2) IC405 8-759-338-78 IC BA10324AFV-E2 A-7074-097-A PS-427 BOARD, COMPLETE ********************* IC406 8-752-377-38 IC CXD2430N-T4 (Ref.No. : 2000 Series) IC407 8-759-426-25 IC MB88346LPFV-G-BND-ER < COIL >

Parts list of the PS-427 board is not shown.

L401 1-469-525-91 INDUCTOR 10uH L402 1-469-525-91 INDUCTOR 10uH Pages from 6-12 to 6-13 are not shown. L403 1-469-525-91 INDUCTOR 10uH L404 1-469-525-91 INDUCTOR 10uH < TRANSISTOR > Q401 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q402 8-729-037-74 TRANSISTOR UN9213J-(K8).SO Q403 8-729-037-53 TRANSISTOR 2SA1832F-Y/GR(TPL3) Q404 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q405 8-729-425-47 TRANSISTOR XP4316-TXE Q406 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO < RESISTOR > R402 1-218-977-11 RES,CHIP 100K 5% 1/16W R403 1-218-965-11 RES,CHIP 10K 5% 1/16W R404 1-218-968-11 RES,CHIP 18K 5% 1/16W R405 1-208-699-11 METAL CHIP 4.7K 0.50% 1/16W R406 1-216-797-11 METAL CHIP 10 5% 1/16W R407 1-208-927-11 METAL CHIP 47K 0.50% 1/16W R408 1-208-707-11 METAL CHIP 10K 0.50% 1/16W R409 1-208-721-11 METAL CHIP 39K 0.50% 1/16W R410 1-218-953-11 RES,CHIP 1K 5% 1/16W R411 1-218-978-11 METAL CHIP 120K 0.50% 1/16W R412 1-218-961-11 RES,CHIP 4.7K 5% 1/16W R413 1-218-977-11 RES,CHIP 100K 5% 1/16W R414 1-218-965-11 RES,CHIP 10K 5% 1/16W R415 1-218-977-11 RES,CHIP 100K 5% 1/16W R416 1-218-973-11 RES,CHIP 47K 5% 1/16W R417 1-218-961-11 RES,CHIP 4.7K 5% 1/16W R418 1-218-947-11 RES,CHIP 330 5% 1/16W R419 1-218-847-11 METAL CHIP 1K 0.50% 1/16W R420 1-218-876-11 METAL CHIP 16K 0.50% 1/16W R421 1-218-969-11 RES,CHIP 22K 5% 1/16W R422 1-218-977-11 RES,CHIP 100K 5% 1/16W R423 1-218-969-11 RES,CHIP 22K 5% 1/16W R424 1-218-977-11 RES,CHIP 100K 5% 1/16W R426 1-218-954-11 RES,CHIP 1.2K 5% 1/16W R427 1-218-966-11 RES,CHIP 12K 5% 1/16W R428 1-218-958-11 RES,CHIP 2.7K 5% 1/16W R429 1-218-980-11 RES,CHIP 180K 5% 1/16W R430 1-218-980-11 RES,CHIP 180K 5% 1/16W R431 1-218-965-11 RES,CHIP 10K 5% 1/16W R432 1-218-980-11 RES,CHIP 180K 5% 1/16W 6-12,

PS-427 SY-56

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7094-686-A SY-56 BOARD, COMPLETE ******************** (Ref.No. : 1000 Series) Parts list of the SY-56 board is not shown. Pages from 6-13 to 6-14 are not shown. 6-13,

SY-56

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

MISCERRANEOUS

************* 5 1-675-589-21 FP-132 FLEXIBLE BOARD 14 1-960-051-11 HARNESS (MD-97) !58 1-418-657-11 FLASH UNIT (MC) 62 1-418-653-11 SWITCH BLOCK, CONTROL (PW) 69 1-960-050-11 HARNESS (MS-114) 70 1-960-061-11 HARNESS (GN-52) 72 1-675-590-11 FP-133 FLEXIBLE BOARD 101 1-418-237-21 TRANSFORMER UNIT, INVERTER 102 1-675-591-21 FP-134 FLEXIBLE BOARD 103 1-418-654-11 SWITCH BLOCK, CONTROL (FK) 118 1-960-060-11 HARNESS (SP-163) 119 1-960-049-11 HARNESS (HB-50) 155 1-418-656-11 FOCUS BLOCK, MANUAL !156 1-418-658-11 FLASH UNIT (ST) 157 1-675-593-11 FP-136 FLEXIBLE BOARD 161 1-418-652-11 SWITCH BLOCK, CONTROL (CF) 204 1-675-592-11 FP-135 FLEXIBLE BOARD 207 1-758-319-21 FILTER BLOCK, OPTICAL BT901 1-694-531-11 TERMINAL BOARD, BATTERY IC101 A-7030-987-A CCD BLOCK ASSY (CCD IMAGER) LCD901 1-803-549-22 MODULE, CRYSTAL INDICATION (LQ20A8FR20) M901 3-709-551-01 MOTOR UNIT, ZOOM STEPPING M902 3-709-400-01 MOTOR, FOCUS STEPPING MIC901 1-542-408-11 MICROPHONE UNIT !ND901 1-517-878-21 TUBE, FLUORESCENT,COLD CATHODE SP901 1-505-862-11 SPEAKER (2.0CM) The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Replace only with part number Ne les remplacer que par une specified. piéce portant le numéro spécifié. 6-14, Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

ACCESSORIES

************ 1-475-851-12 ADAPTOR, AC (J) 1-475-851-22 ADAPTOR, AC (US, CND) 1-475-851-33 ADAPTOR, AC (AEP,UK,E,HK,AUS,JE,CH,KR) 1-569-008-21 ADAPTOR, CONVERSION 2P (E) 1-573-856-11 ADAPTOR, CHANGE (JE) ! 1-769-608-21 CORD, POWER (AEP,UK,E,HK) 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK,HK) 1-772-118-21 COMPACT DISK (Sony Picture Gear 3.2 Lite) (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-772-395-11 DISK, SYSTEM (USB DRIVER SOFT WARE) (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-782-984-31 CABLE, DIGITAL STILL CAMERA (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 1-783-738-31 CORD, CONNECTION (A/V connecting cable 1.5m) 1-783-739-22 CORD, CONNECTION (DK-115 DC connecting cable, 1.6m) ! 1-790-073-11 CORD, POWER 2P (J) ! 1-790-107-22 CORD, POWER (US,CND) 1-791-785-11 CORD, CONNECTION (USB CABLE) (US,CND,AEP,UK,E,HK,AUS,JE,CH,KR) 3-056-776-01 STRAP, WRIST 3-724-594-21 STRING, CAP 3-867-774-01 MANUAL, INSTRUCTION (JAPANESE) (J) 3-867-774-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH) (US,CND,AEP,UK,E,HK,AUS,JE,CH) 3-867-774-21 MANUAL, INSTRUCTION (FRENCH,GERMAN) (CND,AEP,JE) 3-867-774-31 MANUAL, INSTRUCTION (ITALIAN,DUTCH) (AEP) 3-867-774-41 MANUAL, INSTRUCTION (PORTUGUESE,RUSSIAN) (AEP,E,HK,JE,CH) 3-867-774-51 MANUAL, INSTRUCTION (CHINESE) (E,HK,JE,CH) 3-867-774-61 MANUAL, INSTRUCTION (ARABIC,KOREAN) (E,HK,JE,CH,KR) 3-867-774-71 MANUAL, INSTRUCTION (SWEDISH) (AEP) ! A-7033-586-A CODE ASSY (A), POWER (JE) ! A-7033-588-A CODE ASSY (C), POWER (AUS) ! A-7033-589-A CODE ASSY (D), POWER (CH) X-3949-850-1 CAP ASSY, LENS The components identified by Les composants identifiés par une mark ! or dotted line with mark marque ! sont critiques pour la ! are critical for safety. sécurité. Be sure to read “Precautions upon replacing CCD imager” Replace only with part number Ne les remplacer que par une on page 4-10 when changing the CCD imager. specified. piéce portant le numéro spécifié. 6-15E, 〈FOR CAMERA COLOR REPRODUCTION ADJUSTMENT〉 R-Y

MG R YL B CY G

Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts referencesheets with a clear sheet for use. DSC-F505 ✂ – 141 – ✂,

DSC-F505 Sony Corporation

Personal VIDEO Products Company 99I0938-19-974-192-31 Printed in Japan ©1999.9 – 142 – Published by Safety & Service Engineering Dept.,

DSC-F505 US Model Canadian Model SERVICE MANUAL AEP ModelUK Model Level2EModel Hong Kong Model Level 3 Australian Model

2000. 03 Chinese Model

Korea Model Tourist Model SUPPLEMENT-1

File this supplement-1 with the Service Manual. Addition of Adjustment item. : Changed portion. Page Changed contents 1-2-1. INITIALIZATION OF D PAGE DATA 3. D Page Table Initial value RemarkAddress NTSC PAL 5-9 69 80 80 Zoom center adj. 6A Fixed data-1 6B (Initialized data) D1 D2 D3 Fixed data-2 5-10 D4 (Modified data. Copy the data built in D5 the same model.),

DSC-F505

: Added portion. Page Changed contents 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 2. Zoom Center Adjustment Set the A/D value center of the microprocessor to the center voltage of the zoom key. If deviated, the zoom lens operates of itself, even if the zoom key is the center position. Subject Not required Measurement Point Display data of page: 2, address: 5C Measuring Instrument Adjustment remote commander Adjustment Page D Adjustment Address 69 Specified Value 7F to 8B 5-40 Note: Don’t touch the zoom lever during adjustment. Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 2, address: 5C, read the data, and this data is named D5C. 3) When D5C meets the specification value, perform step 5) and later. If D5C is out of specification, check if ZOOM-VR control is in its mechanical center position or not. 4) If the ZOOM-VR control is in the mechanical center, the ZOOM-VR control is defective. Perform step 7). 5) Select page: D, address: 69, set data: D5C. 6) Press the PAUSE button of the adjustment remote commander. 7) Select page: 0, address: 01, and set data: 00.

Sony Corporation

9-974-192-81 Personal VIDEO Products Company 2000C1646-1 Printed in Japan ©2000.3 — 2 — Published by Safety & Service Engineering Dept.]
15

Similar documents

DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06
DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06 On the SY-59 board This service manual contains information This service manual provides the information that is premised the circuit board for japanese model as well.
Page Changed contents
DSC-F55/F55E US Model Canadian Model SERVICE MANUAL Tourist ModelKorea Model DSC-F55 1999. 07 E Model DSC-F55/F55E AEP Model UK Model Australian Model Hong Kong Model Chinese Model DSC-F55E SUPPLEMENT-1 File this supplement-1 with the Service Manual. (99-009) Subject: • Addition of Korea model • Suf
AUTION ou are cautioned that any changes or
DSC-F717 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
Trademarks About the Carl Zeiss lens
DSC-F77/FX77 SERVICE MANUAL LEVEL 1 AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MAN
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL i
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
DSC-H2 SERVICE MANUAL LEVEL 2 US Model UK Model Chinese Model Korea Model Tourist Model
DSC-H2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006. 02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Argentina Model ON BOARD Hong Kong Model Korea Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WI
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1 Ver 1.2 2005. 09 US Model Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model How to use Australian Model Acrobat Reader Chinese Model Japanese Model Korea Model Tourist Model Internal memory ON BOARD Link SPECIFICATIONS BLOCK DIAGRAMS PRIN
SPECIFICATIONS Camera
DSC-H7/H9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2007.04 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: DSC-H7 Black Model Brazilian Model Tourist Model J
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTR
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.1 2005. 04 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.2 2005. 09 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-N2 SERVICE MANUAL SUPPLEMENT-1
DSC-N2 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.02 SUPPLEMENT-1 File this supplement with the service manual. (PV06-161) • Addition of Brazilian Model • Change of Automatic Adjustment Program • Addition of Brazilian Model & : Points added portion. INITIAL LANGUAGE Default Data Check (Service manual pag
DSC-N2 SERVICE MANUAL Canadian Model
DSC-N2 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.1 2007.02 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. (DI06-165) • Addition of
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model UK Model Hong Kong Model Argentine Model Japanese Model Tourist Model Link
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-N2 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Argentine Model Brazilian Model Japanese Model
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory ON BOARD Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Link SPECIFICAT
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.0 2004.04 US Model Canadian Model Revision History E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P100/P120 AEP Model UK Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.2 2004.07 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Correction of exploded view
DSC-P100/P120 LEVEL 2 DSC-P100 SERVICE MANUAL Canadian ModelChinese Model Korea Model Tourist Model Ver 1.2 2004.07 Japanese Model DSC-P100/P120 US Model AEP Model CORRECTION-1 UK ModelE Model Hong Kong Model We will inform you that there are printing errors Australian Model in the service manual pr
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.1 2004.06 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Change of repair parts
DSC-P10/P12 LEVEL 2 US Model SERVICE MANUAL Canadian ModelDSC-P10 AEP Model Ver 1.5 2004. 05 UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model SUPPLEMENT-3 Tourist ModelJapanese Model File this supplement with the service manual. DSC-P10 (PV04-005) • Change of t
Should the fuse in the plug supplied need to be
DSC-P10/P12 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History DSC-P10 AEP Model UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: DSC-P10 DSC-P10 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAM