Download: DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06

DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06 On the SY-59 board This service manual contains information This service manual provides the information that is premised the circuit board for japanese model as well. replacement service and not intended repair inside the SY-59 board. Therefore, schematic diagram, printed wiring board and electrical parts list of the SY-59 board are not shown. The following pages are not shown. Block diagram ... Page 3-9 to 3-16 Schematic diagram... Page 4-9 to 4-34 Printed wirin...
Author: Acal1978 Shared: 8/19/19
Downloads: 1845 Views: 3823

Content

DSC-F55V SERVICE MANUAL E ModelAustralian Model Level 2 Hong Kong Model Chinese Model Tourist Model Japanese Model Ver 1.0 2000. 06 On the SY-59 board This service manual contains information This service manual provides the information that is premised the circuit board for japanese model as well.

replacement service and not intended repair inside the SY-59 board.

Therefore, schematic diagram, printed wiring board and electrical parts list of

the SY-59 board are not shown.

The following pages are not shown. Block diagram ... Page 3-9 to 3-16 Schematic diagram... Page 4-9 to 4-34 Printed wiring board ... Page 4-35 to 4-36 Electrical parts list ... Page 6-8 to 6-14 The above-described information is shown in service manual Level 3. SPECIFICATIONS

System Input and output Power consumption Rated output voltage Accessories Image device connector (during recording) DC OUT: DC 4.2 V, 1.8 A in A/V connecting cable (1) 1/1.8 type color CCD A/V OUT (Monaural) 3.3 W operating mode NP-FS11 battery pack (1) Lens Minijack Operation temperature Battery charge terminal: AC-VF10 AC power adaptor/ f = 6.85 mm Video: 1 Vp-p, 75 Ω, 0°C to 40°C DC 4.2 V, 1.5 A in charge charger (1) (37 mm when converted into a unbalanced, sync negative Storage temperature mode DK-115 DC connecting cable 35 mm still camera) Audio: 327 mV (at a 47 kΩ –20°C to +60°C Operation temperature (1) F = 2.8 load) Maximum dimensions 0°C to 40°C Power cord (1) Exposure control Output impedance: 2.2 kΩ Approx. 103×79×48 mm Storage temperature USB cable (1) Automatic exposure Digital I/O (USB) (w/h/d) –20°C to +60°C Lens cap (1) White balance Special minijack Mass Maximum dimensions Lens cap strap (1) Automatic, Indoor, Outdoor, Approx. 300 g (including 49×39×85 mm (w/h/d) Wrist strap (1) LCD screen battery pack NP-FS11, “Memory Stick” (8 MB) (1)Hold Mass Data system Used LCD panel “Memory Stick,” lens cap, CD-ROM (1) Approx. 120 g Operating Instructions (1) Movie: MPEG1 2 type TFT (Thin Film etc.) Still: JPEG, GIF (in TEXT Transistor active matrix) drive Built-in microphone NP-FS11 battery pack Total number of dots Used battery Design and specifications are mode), TIFF Electret condenser microphone subject to change without Audio with still image: 123 200 (560×220) dots Built-in speaker Lithium ion battery notice. MPEG1 (Monaural) General Dynamic speaker Maximum voltage Recording medium DC 4.2 V Used battery pack “Memory Stick” AC-VF10 AC power Nominal voltage NP-FS11 Flash adaptor/charger DC 3.6 V Power requirements Recommended recording Power requirements Capacity 3.6 V distance: 100 to 240 V AC, 50/60 Hz 4.1 Wh (1 140 mAh) 0.3 m to 2.5 m

DIGITAL STILL CAMERA

, SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered 4. Look for parts which, through functioning, show obvious signs connections. Check the entire board surface for solder splashes of deterioration. Point them out to the customer and and bridges. recommend their replacement. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. "pinched" or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, particularly • Keep the temperature of the soldering iron around 270˚C transistors, that were installed during a previous repair. Point during repairing. them out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. — 2 —, TABLE OF CONTENTS SERVICE NOTE ······························································2·-·6··.···L5CD, INVERTER TRANSFORMER UNIT ··················2-6 2-7. LENS ASSEMBLY, FLASH UNIT, 1. GENERAL MICROPHONE UNIT ····················································2-6 Getting started 2-8. CIRCUIT BOARDS LOCATION ···································2-7 Identifying the parts ····························································2·-·9·.1-1FLEXIBLE BOARDS LOCATION ································2-7 Preparing the power supply ···················································1-1 Setting the date and time······················································3··.1-2 BLOCK DIAGRAMS Inserting the “Memory Stick” ················································31-13. OVERALL BLOCK DIAGRAM (1/2) ···························3-1 Basic operations 3-2. OVERALL BLOCK DIAGRAM (2/2) ···························3-3 B Recording 3-3. POWER BLOCK DIAGRAM (1/2) ································3-5 Recording still images ·························································3·-·41.-3 POWER BLOCK DIAGRAM (2/2) ································3-7 Recording moving images ·····················································1F-o4unctional block diagrams are not shown. B Playback Pages from 3-9 to 3-16 are not shown. Playing back still images ·······················································1-4 Playing back moving images ·················································1-4 Viewing images using a personal computer ··························1-5 4. PRINTED WIRING BOARDS AND Image file storage destinations and image files ·····················1-6 SCHEMATIC DIAGRAMS Advanced operations 4-1. FRAME SCHEMATIC DIAGRAM································4-1 Before performing advanced operations 4-2. PRINTED WIRING BOARDS AND SCHEMATIC How to use the MODE selector ·············································1-6 DIAGRAMS ····································································4-4 How to use the control button ················································1-6 • CD-264 (CCD IMAGER) How to change the menu settings ··········································1-7 PRINTED WIRING BOARD ·························4-5 Menu settings ·········································································1•- 7CD-264 (CCD IMAGER) B Various recording SCHEMATIC DIAGRAM ······························4-7 Rotating the LCD screen — Face-to-Face recording ············1-8 Setting the image size (IMAGE SIZE) ··································1-8 Schematic diagram and printed wiring board of the SY- Recording still images for e-mail (E-MAIL) ·························1-8 59 board are not shown. Adding audio files to still images (VOICE) ··························1-9 Pages from 4-9 to 4-36 are not shown. Recording text documents (TEXT) ·······································1-9 • CONTROL SWITCH BLOCK (MS/HF) Recording uncompressed images (TIFF) ·······························1-9 SCHEMATIC DIAGRAM ····························4-37 Recording images in macro ···················································1-9 • DD-143 (DC/DC CONVERTER) Setting the distance to the subject ··········································1-9 SCHEMATIC DIAGRAM ····························4-39 Using the PROGRAM AE function ·······································1-9 • DD-143 (DC/DC CONVERTER) Adjusting the exposure (EXPOSURE) ··································1-9 PRINTED WIRING BOARD ·······················4-41 Adjusting the white balance (WHITE BALANCE) ············1-10 4-3. WAVEFORMS ······························································ 4-43 Recording the date and time on the still image 4-4. MOUNTED PARTS LOCATION ·································4-48 (DATE/TIME) ······································································ 1-10 Enjoying picture effects (P.EFFECT) ·································· 1-105. ADJUSTMENTS B Various playback 1. Before starting adjustment ···············································5-1 Playing back six images at once (INDEX) ·························· 1-10 1-1. Adjusting items when replacing main parts and boards ··5-2 Enlarging a part of the still image (Zoom and trimming) ····1-10 5-1. ADJUSTMENTS·····························································5-3 Rotating a still image (ROTATE) ·········································1-111-1. PREPARATIONS BEFORE ADJUSTMENT ·················5-3 Playing back the images in order (SLIDE SHOW) ·············1-11 1-1-1.List of Service Tools ························································5-3 Viewing images on a TV screen ·········································· 1-111-1-2.Preparations ·····································································5-4 B Editing 1-1-3.Discharging of the strobe power supply ··························5-4 Preventing accidental erasure (PROTECT) ·························1-11 1-1-4.Precaution ········································································5-6 Deleting images (DELETE) ················································11-1. 1 Setting the Switch ····························································5-6 Changing the recorded still image size (RESIZE) ··············· 1-12 2. Order of Adjustments ······················································5-6 Copying images (COPY) ·····················································31.-12 Subjects ···········································································5-6 Selecting still images to print (PRINT MARK) ·················· 1-12 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA ·········5-7 Additional information 1-2-1. INITIALIZATION OF D PAGE DATA ··························5-7 Precautions ······································································1··.··· 1-I1n2itializing the D Page Data ············································5-7 On “Memory Sticks” ··························································2·.1-13 Modification of D Page Data ···········································5-7 Using your camera abroad ··················································· 13-.13 D Page Table ····································································5-7 Troubleshooting ································································1··-·21-2-1. I3nitializing the B, E, F, 7 Page Data ································5-8 Warning and notice messages ·············································· 1-11.4 Initializing the B, E, F, 7 Page Data ································5-8 Self-diagnosis display ·························································2· 1. -14 Modification of B, E, F, 7 Page Data ·······························5-8 LCD screen indicators ·························································31. -15 F Page Table ····································································5-9 4. 7 Page Table ···································································5-10 2. DISASSEMBLY 5. E Page Table ·································································· 5-11 2-1. CABINET (FRONT) ASSEMBLY, CHECK COVER ····2-1 6. B Page Table ·································································· 5-11 2-2. DD-143 BOARD ··························································1··-·32. -2VIDEO SYSTEM ADJUSTMENTS·····························5-12 2-3. CAMERA BLOCK ASSEMBLY ····································2-21. Video Output Level Adjustment (SY-59 board) ············5-12 2-4. SY-59 BOARD ····························································1··-·4·.2-3CAMERA SYSTEM ADJUSTMENTS ························5-13 2-5. LCD PANEL BLOCK, SPEAKER (2.0CM), 1. HALL Adjustment ·························································5-13 CONTROL SWITCH BLOCK (MS)/(HF) ·····················2-5 2. Flange Back Adjustment (Using Minipattern Box) ·······5-14 — 3 —, 3. Flange Back Adjustment (Using Flange Back Adjustment Chart) ························5-15 4. Flange Back Check ························································5-15 5. F No. Standard Data Input ·············································5-15 6. Mechanical Shutter Adjustment ····································5-16 7. Picture Frame Setting ····················································5-17 8. Light Level Adjustment and ND Shutter Check ············5-18 9. Mixed Color Cancel Adjustment ···································5-18 10. Auto White Balance Standard Data Input ·····················5-19 11. Auto White Balance Adjustment ···································5-19 12. Color Reproduction Adjustment ····································5-20 13. Color Reproduction Check ············································5-21 14. White Balance Check ····················································5-22 15. Strobe White Balance Adjustment ·································5-23 16. Strobe Light Level and White Balance Check ·············· 5-23 17. CCD Black Defect Compensation ·································5-24 18. CCD White Defect Compensation ································5-24 1-5. LCD SYSTEM ADJUSTMENT ···································5-25 1. LCD Initial Data Input ··················································5-25 2. VCO Adjustment (SY-59 board) ···································5-26 3. D Range Adjustment (SY-59 board) ······························5-26 4. Bright Adjustment (SY-59 board) ··································5-27 5. Contrast Adjustment (SY-59 board) ······························5-27 6. Color Adjustment (SY-59 board) ···································5-28 7. V-COM Level Adjustment (SY-59 board) ·····················5-28 8. V-COM Adjustment (SY-59 board) ·······························5-29 9. White Balance Adjustment (SY-59 board) ····················5-29 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT ········5-30 1. Battery End Adjustment (SY-59 board) ·························5-30 5-2. SERVICE MODE ··························································5-31 2-1. ADJUSTMENT REMOTE COMMANDER ················5-31 1. Using the Adjustment Remote Commander ·················· 5-31 2. Precautions Upon Using the Adjustment Remote Commander ···································································5-31 2-2. DATA PROCESS ···························································5-32 2-3. SERVICE MODE ··························································5-33 1. Setting the Test Mode ····················································5-33 2. Bit Value Discrimination ···············································5-33 3. Emergency Memory Address of Flash Unit ·················· 5-33 4. Record of Use check ······················································5-34 5. Self Diagnostics Log check ···········································5-34 6. Switch check (1) ····························································5-35 7. Switch check (2) ····························································5-35 8. LED check ·····································································5-35 9. Position sensor check (SY-59 board SE401) ·················5-36 6. REPAIR PARTS LIST 6-1. EXPLODED VIEWS ······················································ 6-1 6-1-1.OVERALL SECTION ·····················································6-1 6-1-2.CABINET (FRONT) SECTION ·····································6-2 6-1-3.CAMERA BLOCK SECTION ······································· 6-3 6-1-4.CABINET (REAR) SECTION ······································· 6-4 6-2. ELECTRICAL PARTS LIST ·········································· 6-5 Electrical parts list of the SY-59 board is not shown. pages 6-8 to 6-14 are not shown. * Color reproduction frame is shown on page 105. — 4 —,

SERVICE NOTE

• NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don't pull at wire of connector. bent at the terminal. Be in danger of the snapping of a wire. Do not insert the cable insufficiently nor crookedly. When installing a connector, don't press down at wire of connector. Be in danger of the snapping of a wire. Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside) [Discharging of the FLASH unit’s charging capacitor] The charging capacitor of the FLASH unit is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the DSC-F55V is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig Discharging the Capacitor To preparing the short jig. a small clip is attached to each end of a Short circuits between the positive and the negative terminals of resistor of 1 kΩ /1 W (1-215-869-11) charged capacitor with the short jig about 10 seconds. Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. Capacitor 1 kΩ/1 W Short jig Wrap insulating tape. FLASH UNIT — 5 —, [Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss The contents which can be handled by customer, are displayed. • E: ss: ss The contents which can be handled by engineer, are displayed. Display Code Countermeasure Cause Caution Display During Error C:32:01 Turn off the main power then back on. Trouble with hardware. SYSTEM ERROR • The type of memory stick that cannot Replace the memory stick. be used by this machine, is inserted. C:13:01 Format the memory stick with the DSC- MS ERROR • Data is damaged. F55V. • Unformatted memory stick is inserted. Flash LED Checking of flash unit or replacement of Abnormality when flash is being E:91:01 Flash display flash unit charged. *2 Flashing at 3.2 Hz E:61:00 *1 Checking of lens drive circuit When failed in the focus initialization. — E61:10 *1 Note : The error code is cleared if the battery is removed, except defective flash unit. *1: The error display is given in two ways. *2: When the flash charginf failed, Page: D, Address: 67, Data:04 are written. After repair, be sure to write Page: D, Address: 67, Data: 00. — 6 —,

DSC-F55V SECTION 1

This section is extracted from

GENERAL instruction manual.

1-1,

DSC-F55V SECTION 2 DISASSEMBLY

The following flow chart shows the disassembly procedure. 2-1. Cabinet (front) assembly, Check cover 2-2. DD-143 board DD-143,CD-264 boards 2-3. Camera block assembly service position 2-4. SY-59 board 2-7. Lens assembly, Flash unit,Microphone unit 2-5. LCD panel block, Speaker (2.0cm), Control switch block (MS) / (HF) Main (SY-59) board, DD-143 board LCD service position 2-6. LCD, Inverter transformer unit NOTE: Follow the disassembly procedure in the numerical order given. 2-1. CABINET (FRONT) ASSEMBLY, CHECK COVER

P

(Fig 1) Remove the check cover by rotating 4 Battery terminal the metal bar in the direction of the board (3p) arrow of ø1.6 or less centering around the point “P”. Note: Do not reuse the check cover that is once removed. SY-59 3 Two screws (M1.7 × 3), lock ace, p2 6 Check cover (Refer to Fig 1) 1 Screw (M1.7 × 3), lock ace, p2 5 Cabinet (front) assembly 2 Two screws (M1.7 × 3), lock ace, p2 2-1

DSC-F55V

, 2-2. DD-143 BOARD qa DD shield case A qs DD-143 board 2 Harness (MC-081) (3p) 9 DD shield caseB3Harness (DB-51) (5p) 8 Two claws DD-143 q; Claw 4 Screw (M1.7 × 3), lock ace, p2 5 Plate nut71FP-109 flexible board (40p) 6 Screw (M1.7 × 3), lock ace, p2 2-3. CAMERA BLOCK ASSEMBLY 4 FP-108 flexible board (9p) SY-59 6 Screw (M2 × 4.5), tapping head (2 lock) q; Lens cabinet (rear) assembly (Remove the three claws.) Camera 5 Harness (DC-67) (3p)7 block assembly 8 Flexible stabilizer Be careful when handling it as it is not fixed. 2 FP-107 flexible board (22p) 3 Flexible board 1 Flexible retainer sheet (from lens block) (16p) 9 Two step screws 2-2, [ DD-143, CD-264 BOARDS SERVICE POSITION ] Note 1: The built-in charging capacitor inside the FLASH unit is charged to the maximum of 300 V. There is a danger of electric shock due to the high voltage when the battery is handed by bare hand. Discharge the voltage remained in the battery, referring to the Service Note (See page 5). FP-108 flexible board (9p) Harness (MC-081) (3p) Harness (DC-67) (3p) Flexible board (from lens assembly) (16p) CD-264 FP-107 flexible board (22p) Adjustment remote commander (RM-95) SY-59 Battery terminal board (3p) Harness (DB-51) (5p) CPC-9 jig (J-6082-393-C) (Note 2) 431 FP-109 flexible board (40p)

DD

- AC POWER AC IN ADAPTOR Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 3: Don't use the 12pin flexible board of CPC-9 jig. It causes damage to the unit. 2-4. SY-59 BOARD qg Screw (M1.7 × 3), lock ace, p2 qh DD flame SY b -59 qd FP-109 flexible board (40p)oard 2 FP-108 flexible board (9p) 3 Flexible board (from control switch block (MS)) qs

S

(15p) Ybo -5a 9rd 9 Screw (M1.7 × 3), lock ace, p2 4 Flexible board 1 FP-110 flexible board (24p) (from control switch block (HF)) (6p) Harness (DC-67) (3p) qf SY-59 board5 qa Claw q; Two screws (M1.7 × 3), lock ace, p2 7 Flexible board (from lens assembly) (16p) 8 FP-101 flexible board (22p) 6 Flexible retainer sheet 2-3, [ MAIN (SY-59) BOARD, DD-143 BOARD, LCD, SERVICE POSITION ] Note 1: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 2: Don't use the 12pin flexible board of CPC-9 jig. It causes damage to the unit. Adjustment remote commander (RM-95) FP-101 flexible board (22p) Flexible board (from lens assembly) (16p) LCD Flexible board

SY (from control switch block (HF))

bo-5 (6p)ar 9d SY-59 board CPC-9 jig (J-6082-393-C) (Note 2) FP-110 flexible board (24p) Battery terminal board (3p) Flexible board D (from control switch block (MS)) b Doa-14 (15p)rd 3 FP-108 flexible board (9p) FP-109 flexible board (40p) DD-143 board AC POWER AC IN

ADAPTOR

2-4, 2-5. LCD PANEL BLOCK, SPEAKER (2.0CM), CONTROL SWITCH BLOCK (MS)/(HF)

REMOVING THE SLEEVE AND THE AE LEAF SPRING ASSEMBLY

Mode dial Rear cabinet2

PRECAUTION DURING

4 AE leaf spring

INSTALLATION assembly

When installing it, Note : When installing it, align the switch position 3 Sleeve align the sleeve and as shown. the mode dial as shown. Control switch block (MS) 1 Tapping screw 5 Speaker (2.0 cm) 4 Control switch block (MS) 2 Screw (M2 × 4.5), tapping head (2 lock) 3 Two screws (M2 × 4.5), tapping head (2 lock) 0 LCD panel block Control switch block (HF) When installing it, 1 Panel insulating sheet align the switch position as shown.

PRECAUTION DURING INSTALLATION

8 Function knob 9 Control switch block (HF) 6 HF cushion 7 Three screws (M2 × 4.5), tapping head (2 lock) 2-5, 2-6. LCD, INVERTER TRANSFORMER UNIT qs Cold cathode fluorescent tube 7 Harness (DB-51) (5p) 4 Two claws 8 Inverter transformer unit 2 Crystal indication module 3 Screw (M1.7 × 2), lock ace, p2 1 Crystal indication module (23p) 5 qa Back light sheet 9 Screw (M1.7 × 2), lock ace, p2 6 Cold cathode fluorescent tube (20p) q; FP-110 flexible board 2-7. LENS ASSEMBLY, FLASH UNIT, MICROPHONE UNIT Note : The built-in charging capacitor inside the FLASH unit is charged to the maximum of 300 V. 8 Flash unit There is a danger of electric shock due to the high voltage when the capacitor is handed by Remove the three bare hand. Discharge the voltage remained in the capacitor, referring to the Service Note claws as shown. (See page 5). q; Two screws (M2 × 4.5), tapping head (2 lock) qs Microphone retainer 6 Harness (MC-081) (3p) qd Sound absorption sheet (D) qa Microphone cushion Be careful when handling it as it is not fixed. 5 Microphone unit (2p) qf Microphone unit 4 Two screws (M2 × 4.5), tapping head (2 lock) 9 Harness (DC-67) (3p) 7 Lens block assembly 7 CCD block assembly (CCD imager) 3 FP-107 flexible 6 Seal rubber (K) boardCD-26 5 Optical filter block42Flexible cushion 4 CCD fitting adaptor (K) 2 Lens assembly 8 CD-264 board 1 Lens flexible ring 1 Two tapping screws (B1.7 × 6) 3 Two claws

REMOVING THE CD-264 BOARD, LENS ASSEMBLY

2-6, 2-8. CIRCUIT BOARDS LOCATION FLASH UNIT CD-264 (CCD IMAGER) INVERTER TRANSFORMER UNIT DD-143 (DC-DC CONVERTER) SY-59 CAMERA, CAMERA DSP, LCD DRIVE, TIMING GENERATOR, VIDEO, SH DSP, AUDIO, LENS MOTOR DRIVE, HI CONTROL, A/V OUT, USB, CONNECTOR 2-9. FLEXIBLE BOARDS LOCATION FP-108 CONTROL SWITCH BLOCK (MS) CONTROL SWITCH BLOCK (HF) FP-109 FP-110 FLEXIBLE BOARD (From CAM MOTOR) FP-107 2-7E,

DSC-F55V SECTION 3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

CD-264 BOARD(1/2) SY-59 BOARD

(4-11) (4-8) (4-9) LENS IRIS(SHUTTRE) IC102 12 AD DATA 12IC102 CCD OUT IC301 16 DATA BUS S/H,AGC, CAMERA DSP CCD IMAGER A/D CONV. MEMORY CONTROL VIDEO ENCODER 14 OPD,OSD,HOST IF ADDRESS BUS FOCUS (4-9) RES CONTROL MOTOR SG,JPEG,L-MODE IRIS V1,V1B,V2, METER V3A,V3B,V4,M M RG,VSHT IC101 AUDIO I/F HALL H1,H2 TIMING MCK18 MCK18 SHUTTER CONTROLFOCUS H RESET GENERATOR STROBO CONTROL

SENSOR

(4-14)

IC202 MC XCS2IRIS CONT 1,2 ADDRESS MC XCS6

CAM SO,XCAM,SCK IC303 14

IC203 IC304 DATA AU SDTO FOCUS

MOTOR SHUTTER IRIS DRIVE DRIVE SDRAM 16 AU SDTIDRIVE HALL (+) HALL AD 64MbitX2 HALL AMP

IC201 (4-19)

(4-27)

Y

XFC RST SENS XFC RST SENS IC651 VIDEO OUT (4-27) C VIDEO AMP

Y

MSHUT ON ENO R-Y DIROA CONTENUDE ONENO DIROA DIROB B-Y (SEE PAGE DIROB MSHUT ON STRB ON VD,HD 3-3) (4-12)

IC204

STRB ON

FLASH EVRFLASH ST UNREG UNIT UNIT STB CHARGE

CAM SO,XCAM SCK BT901

BATTERY TERMINAL S BATT SIG

CAM DD ON SYS DD ON LCD DD ON

IC001 M 5VA 4.9V

CAM -7.5V

IC002 CAM 15V

D 3.2V DC/DC A 3.2V CONVERTER D 1.8V PANEL -15V (4-39,40) PANEL 13.5V PANEL 6.5V PANEL 4.9V EVER 3.5V HI UNREG ST UNREG

DD-143 BOARD

3-1 3-2,

DSC-F55V

3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

SY-59 BOARD

(4-32) USB D+

IC601 USB D- CN951DATA BUS

16 16 16 USB USB I/F ADDRESS BUS 20 14 19 (4-21)

IC501 IC506 IC504

SDRAM FLASH ROM MC CAM 64Mbit 16Mbit SH DSP (4-24) (4-24) MC XCS2 MC XCS6 MC XCS2 MC XCS0 USB D+/- OUT, USB D+/- IN CN101 MS DIO, MS SCLK MEMORYSTICK (4-29) (4-29) S104-106 CONTENUDE ON EVER 3.5V IC407 EVER 3.2V (SEE PAGE IC404 KEY AD 0 DIGITAL ZOOM T/W SW(4-24) LENS SW 3-2) 3.2V REG HI CONTROL

IC507 IC402 XCAM/PB SW S102RESET MOVIE/XSTILL SW

PLAY/STILL/MOVIE SW EEPROM IC408 RESET S101XPWR SW HI UNREG POWER SW RESET (4-29) (4-29) D101XPOWER LED POWER LED CONTROL CAM SO,XCAM SCK HI SO,HI SI,XHI SCK XSHTR SW S103,107 SWITCH XSHTR LOCK SW SHUTTER SW BLOCK(MS) HALL AD (4-30)

IC406 KEY AD1 S101-107

KEY AD2 FUNCTION SW EEPROM CONTROL (4-25) D103 STB LED BEEP FLASH LED SWITCH

IC702 BLOCK(HF)

(4-25) AUDIO OUT LINE/

SPEAKER

AU SDTO IC252 AU OUT AMP AU SDTI AU IN MIC AMP AU SP+,SP- AUDIO (4-30) AD/DA MIC SIG BATT SIG CONV. 32KHZ BATT STB CHARGE IC405 BT001 SYS DD ON LITHIUM BATTERY

TIMER

LCD DD ON CLOCK CAM DD ON EVER 3.2V VIDEO OUT VIDEO OUT J951 A/V OUT AUDIO OUT AU SP+,SP- SP901

SPEAKER

(4-15) (4-17)

IC801 LCD901

HI SO,XHI SCK IC901 LCD EVR PANEL

TIMING GENERATOR

(4-8) MIC901 IC101 VD,HD MICYR

MIC

AMP R-Y IC803 G B-Y LCD B

CD-264 DRIVE

16 BOARD(2/2) (4-16) ND901 BL UNREG INVERTER

BACK

UNIT LIGHTUNIT 3-3 3-4,

DSC-F55V

3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

DD-143 BOARD

CN002 ST UNREG 3 POWER(2/2)(FLASH UNIT) BATT SIG L001 D002 EVER +3.5 10 DC/DC CONV. 2 (4-40)F001 4 IC002(STEP UP) BT901 3 BATTERY F002

TERMINAL

F003 HI UNREG BATT UNREG F004 1 T001 D004(1/2) RECT L016 Q032,033

S BATT SIG PANEL +13.5V2 8 11

BATT GND 3 IC001 L013 PANEL +6.5V7 13 CN001 (4-39) Q009 DC/DC CONVERTER SWITCHING D004(2/2) T003 2 EMERGENCY DC/DC CONVERTER D006 1 DETECTRECT D005 V+=UN+2.2V RECT 5 53 VCC(0)1-2 OUT6 63 58 VCC(0)3,4 L012 Q030,031 PANEL -15V 7 64 VCC(0)5,6,7 -IN(A)6 104515 V-=UN-1.6V 8 54 VSS(0)1-2 -IN(E)6 12 L009 PANEL +4.9V 59 VSS(0)4,5,6 25

VCC

=UN+2.2V -IN(C)6 14 L010 CAM +15V 26 VCC4516 VG=8V4251 VG(0)1 OUT5 623613D001 Q01027D007RECT SWITCHING RECT 8 +IN(E)7 -IN(C)5 17 L015 CAM -7.5V1814 7 -IN(E)7-2 T002 1 OUT7 -IN(E)5 18 Q011 SWITCHING Q025 -IN(C)8 23 EMERGENCY Q023(1/2) Q023(2/2)DETECT Q024(1/2) Q024(2/2) L004 Q021 24 VREF SWITCHING Q016,017 L011 A +4.9V 17 A4.9V POWER(2/2) 18 (SY-59) Q003,005,006 OUT4 61 (ON PAGE

DRIVE

33 RT 3-7) 34 CT -IN(E)4 21 L005 Q022SWITCHING L005 M +5V 19 M5V LCD 0N Q004,007,008 29 CTL6 OUT3 60 DRIVE CAM ON 28 CTL5 DD ON -IN(E)3 36 27 CTL1-4,7 Q012 Q019 Q014 SWITCHING SWITCHING L007 D +1.8V 23 D1.8V L003 24 OUT2-1 55 OUT2-2 57 L008 D +3.2V D3.2V -IN(E)2 39 28 Q020

SWITCHING

Q013 SWITCHING L002 A +3.2V A3.2V OUT1-2 48 30 L014 OUT1-1 52 Q002(1/2)Q029(1/2) Q015 SWITCHING BL LED ON XBL LED ONOUT1-3 49 9 CN003 BL UNREG11-IN(E)1 44

BACK BL ON3 3 LIGHT BL PWM Q002(2/2)

BL ON44Q029(2/2)

UNIT BL LED ON5 5

DD ON SYS DD ON LCD ON LCD DD ON CAM ON CAM DD ON BL PWM BL PWM CN004 3-5 3-6 CAM ON LCD ON,

DSC-F55V

3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Page No. shown in ( ) indicates the page to refer on the schematic diagram.

SY-59 BOARD

STB CHG ST UNREG Q409 (4-29) STB CHG 93663XSTB FUL BATT SIG 48 BATT SI XSTB FULL 3255FLASH 5 IF BLOCK IC404 STB ON 49 BATT SO44UNIT

IC407 (4-29) HI CONTROL A 4.9V 3 3

EVER 3.5V 42,51 CN701 3.2V 9,11 2 REG 3 75,76 BACKUP VCC 77,86 (4-29) 87 HI UNREG 7 IC408 (4-29) IC402 (4-15) (4-16) (4-17) (4-17)

IC801 IC803 IC901 IC902

2 RESET12RESET 1 38 XREST EVR LCD TIMING COMDRIVE GENERATOR AMP LCD901 XPOWER 14 VSH P 4.9V 12 71 BATT SENS Q411 PANEL 4.9V L903 VSH 60 LCDPOWER LED LED DRIVE PANEL -15.3V L902 VSS 15 UNIT PANEL 13.2V L901 VGH 72 ACV SENS 23 PANEL 6.5V CN901 XBL LED ON D 3.2V 10 92 DD CON SENS BL PWM A 3.2V L801 CAM DD ON 4 11 BL LED ON BL ON 3 43 BL ON SYS DD ON 2 57 XBL PWM CN703 XPWR SW LCD DD ON3125 CAM DD ON POWER LED CONTROL 47 LCD DD ON S101 SWITCH 29 SYS DD ON BLOCK(MS) D 3.2V D101 POWER 4 (POWER) (4-37)

VCC

9 MEMORY10 BT001 STICK POWER(1/2) EVER 3.2V D410 R485 LITHIUM BATTERY Q701,702 CN101 (DD-143) (ON PAGE MS POWER ON 3-6) (4-30) (4-30) D 3.2V CONTROL

IC406 IC405 1 LED

CN702 SWITCH PANEL +4.9V (4-38) BLOCK(HF) 26 EEPROM TIMER BLOCK PANEL -15V 16 IC601 PANEL +6.5V PANEL +13.5V USB I/F (4-9) (4-9) CAM 15V 15 IC102 IC101 CAM -7.5V 13 CD-264 BOARDS/H AGC TIMING A/D CONV. GENERATOR (4-8) CAM -7.5V CAM -7.5V 10 14 IC102 CAM 15V CAM 15V 9 15 A +4.9V A 3.2V CCD CN101 IMAGER

IC301 STB ON A 4.9V CN101199

(4-25) (4-14) (4-21) (4-24) (4-24) (4-24) (4-22) (4-8) (4-11) CAMERA DSP

IC303 IC501 IC504 IC506 IC507 IC503 IC701MEMORY CONTROL A 4.9V IC101VIDEO ENCODER2331

OPD,OSD,HOST IF REG RES CONTROL IC304 CN707 CN103 MIC AMP SG,JPEG,L-MODE MCCAM FLASH ROM SDRAM EEPROM INVERTER 64 Mbit SH-DSP 16Mbit 64Mbit SDRAM X2 D 1.8V D 1.8V 23,24 D 3.2V D 3.2V 25,27,28 A 3.2V A 3.2V 29,30,31 A 4.9V A 4.9V 17,18 DAC ENB M5V M5V 19,20 CH 3.2V L204 CN705 (4-25) (4-25) L651 L201 L203 L203 XLENS RST LED LENS L255 IC702 IC252 UNITSP VCC Q651,652 Q204,205 SENS VCC FOCUS LINE/ AUDIO 4 RESET Q253 SPEAKER AD/DA REG SENSOR AMP CONV. Q203 +3.1V CN201 10 18 17 CN704 IC651 IC201 IC202 IC203 IC204 CPC FOR CHECK

SHUTTER

VIDEO DRIVE IRIS HALL EVR AMP FOCUS MOTOR DRIVE AMP D/A DRIVE CONV. (4-19) (4-27) (4-27) (4-27) (4-28) 3-7 3-8E

UNREG VDD RESET

,

DSC-F55V SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM12345678910 11 12 13 14 15 16 17 18 19 20 21 CN101 10P CONTROL SWITCH BLOCK CONTROL SWITCH BLOCK 10 Vss

A (MS) (HF)9 Vcc CD-264 BOARD

8 SCLK LENS S101 CCD 7 NC D101 D106 UNIT IMAGER(POWER LAMP) (ACCESS LAMP) MENU

FLASH UNIT 6 INT S101,104,105 MEMORY

STICK 5 NC POWER,DIGITAL ZOOM T/W 4 DIO 3 ST UNREG 3 NC S106 2 ST GND S102 D103 2 BS LCD

B (FLASH LAMP)1 SEIDEN GND MODE BACK LIGHT1 Vss ON OFF

PLAY STILL MOVIE S103 (SHUTTER) (FLASH) PROGRAM AE

MC-081 S106HARNESS (LENS) FP-107 MIC FP-108 DISPLAY,VOLUME +/- PROGRAM AE ADJ(FWD) (REV) FLEXIBLE MIC901 FLEXIBLE C CN004 40P CN705 40P

DD ON11LCD_DD_ON LCD ON22SYS_DD_ON CAM ON33BL_ON BL ON44CAM_DD_ON BL PWM55BAT_SIG BATT SIG66BLPWM GND77HI_UNREG

D HI UNREG88REG_GND

BL LED ON99EVER+3.5V EVER+3.5V 10 10 XBL_LED_ON J951 PANEL+13.5V 11 11 EVER+3.5V A/V OUT EVER+3.5V 12 12 PANEL+13.5V PANEL+6.5V 13 13 CAM-7.5V SY-59 BOARD CAM-7.5V 14 14 PANEL+6.5V PANEL-15V 15 15 CAM+15V

E 7/13 SH BLOCK CAM+15V 16 16 PANEL_-15V 1/13 CH BLOCK

A+4.9V 17 17 A+4.9V 2/13 PEARL BLOCK 8/13 SH BLOCK A+4.9V 18 18 A+4.9V

DD-143 3/13 PEARL BLOCK 9/13 AU BLOCKM+5V 19 19 M+5V BOARD 4/13 RGB BLOCK 10/13 LD BLOCKM+5V 20 20 M+5V

GND(M) 21 21 GND(M) 5/13 TG BLOCK 11/13 HI BLOCK GND(M) 22 22 GND(M) 6/13 VI BLOCK 12/13 USB,JK BLOCK D+1.8V 23 23 D_1.8V

F 13/13 CN BLOCKD+1.8V 24 24 D_1.8V

PANEL+4.9V 25 25 D_3.2V D+3.2V 26 26 PANEL+4.9V BT001 D+3.2V 27 27 D_3.2V LITHIUM BATTERY D+3.2V 28 28 D_3.2V A+3.2V 29 29 A_3.2V A+3.2V 30 30 A_3.2V GND 31 31 A_3.2V

G A+3.2V 32 32 REG_GND

GND 33 33 REG_GND GND 34 34 REG_GND GND 35 35 REG_GND GND 36 36 REG_GND GND 37 37 REG_GND GND 38 38 REG_GND GND 39 39 REG_GND

H GND 40 40 REG_GND

CN001 3P

DB-51 BATT GND 3 HARNESS BT901

BATT SIG2SBATTERYTERMINAL SS-72 CPC BATT UNREG 1 HARNESS (FOR CHECK) DIGITAL I/O (USB)

I FP-110

SP901 FLEXIBLE

SPEAKER J INVERTER TRANSFORMER UNIT ND901BACK-LIGHT

LCD901 COLOR LCD

UNIT K FRAME SCHEMATIC DIAGRAM

4-1 4-2 CN003 5P CN002 3P 5P 5 BL LED ON SEIDEN GND 1 BL UNREG14BL PWM ST GND 2 BL GND23BL ON ST UNREG 3 BL ON32BL GND BL PWM41BL UNREG BL LED ON 5

FP-109 FLEXIBLE

CN706 2P 2 SP - CN701 9P 1 SP + XTALLY_LED91XTALLY_LED PHOTO_TR_OUT82PHOTO_TR_OUT REG_GND73REG_GND STRB_CHG64STRB_CHG XSTRB_FULL55XSTRB_FULL STRB_ON46STRB_ON A_4.9V37A_4.9V N.C28N.C STRB_PHOTO_ON19STRB_PHOTO_ON CN703 15P CN1 24P CN901 23P REG_GND 15 VGH 24 1 CLD XSHTR_LOCK_SW 14 VSH 23 2 SPD XSHTR_SW 13 VCC 22 3 CTR KEY_AD0 12 CLS 21 4 EX3 BS 11 SPS 20 5 EX2 VCC 10 EX1 19 6 VB12 DIO 9 MO1 18 7 RES INT 8 MO2 17 8 VR SCLK 7 VSS 16 9 VG MOVIE/XSTILL_SW 6 VGL 15 10 VB XCAM/PB_SW 5 COM 14 11 GND D_3.2V 4 VSH 13 12 VSH XPWR_SW 3 GND 12 13 COM ACCES_LED 2 VB 11 14 VGL PWR_LED 1 VG 10 15 VSS VR 9 16 MO2 TST 8 17 MO1 RES 7 18 EX1 VB12 6 19 SPS EX2 5 20 CLS EX3 4 21 VCC CTR 3 22 VSH SPD 2 23 VGH CLD 1 CN704 18P 18 VDD 17 RESET 16 RXD 15 TXD 14 RF7 13 N.C 12 LANC_OUT 11 LANC_IN CN702 6P 10 UNREG N.C69VG KEY_AD158PANEL_COM KEY_AD247HSY REG_GND36N.C STB_LED25XCPC_IN D_3.2V14REG_GND 3 N.C CN201 16P 2 N.C DRIVE+ 16 1 N.C DRIVE- 15 BIAS+ 14 HALL+ 13 BIAS- 12 HALL- 11 GND 10 CN951 4P GND91VCC FOCUS_A- 82D- FOCUS_B- 73D+ FOCUS_A64GND FOCUS_B 5 SENS_VCC 4 FORCUS_RST 3 SENS_GND 2 TEMP_OUT 1

DC-67

CN707 3P CN103 3PHARNESS MIC_SIG13MIC_SIG GND22A_GND AU_4.9V31AU_4.9V CN101 23P CN101 22P 1 CCD_GND CCD_GND 22 2 CCD_OUT CCD_OUT 21 3 CCD_GND CCD_GND 20 4 CCD_GND CCD_GND 19 5 V2 V2 18 6 V4 V4 17 7 V1A V1A 16 8 V1B V1B 15 9 V3A V3A 14 10 V3B B3B 13 11 NC VSHT 12 12 VSHT VSUB_CONT 11 13 VSUB_CONT CAM_-7.5V 10 14 CAM_-7.5V CAM_15V 9 15 CAM_15V HDR_GND 8 16 HD_GND HDR_GND 7 17 HD_GND H2 6 18 H2 RG 5 19 RG H1 4 20 H1 REG_GND 3 21 REG_GND REG_GND 2 22 REG_GND REG_GND 1 23 REG_GND CN102 2P 2 MIC GND 1 MIC SIG,

DSC-F55V DSC-F55V

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) • b: Pattern from the side which enables seeing. • Voltages and waveforms are measured between the measure- (The other layers' patterns are not indicated.) ment points and ground when camera shoots color bar chart of • Through hole is omitted. pattern box. They are reference values and reference wave- • Circled numbers refer to waveforms. forms. * • There are few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used.). isn’t mounted in this model. • Voltage values change depending upon input impedance of VOM • Chip parts. used.) * Transistor DiodeC65445645123331. ConnectionBE123321321543212121Pattern box (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µµF. 50V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10W unless otherwise noted. kΩ=1000Ω, MΩ=1000kΩ. • Caution when replacing chip parts. About 32 cm New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Be- cause it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Front of the lens Kinds of capacitor Temperature characteristics External dimensions (mm) 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. H In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2 : non flammable resistor • 1 : fusible resistor • C : panel designationABA=BBA• A : B+ Line * Fig. a (Video output terminal output waveform) • B : B– Line * • J : IN/OUT direction of (+,–) B LINE. * • C : adjustment for repair. * Electron beam • Circled numbers refer to waveforms. * scanned frame * Indicated by the color red. Note : The components identified by mark 0 or dotted CRT picture frame line with mark 0 are critical for safety. Replace only with part number specified. Fig.b (Picture on monitor TV) When indicating parts by reference number, pleas include the board name. 4-4 Yellow Cyan Green Yellow White Cyan Magenta Green Red White Blue Magenta Red Blue,

DSC-F55V CD-264 (CCD IMAGER) PRINTED WIRING BOARD

— Ref. No. CD-264 Board; 3,000 Series —

For printed wiring boards

• Refer to page 4-50 for parts location. • CD-264 board consists of multiple layers. However, only the sides (layers) A and B are shown. • Chip parts

Transistor C

B E

There are few cases that the part printed on this

diagram isn’t mounted in this model. FLASH UNIT CD-264 (CCD IMAGER) INVERTER TRANSFORMER UNIT DD-143 (DC-DC CONVERTER) SY-59 CAMERA, CAMERA DSP, LCD DRIVE, TIMING GENERATOR, VIDEO, SH DSP, AUDIO, LENS MOTOR DRIVE, HI CONTROL, A/V OUT, USB, CONNECTOR

CCD IMAGER

4-5 4-6 CD-264,

DSC-F55V For schematic diagram

• Refer to page 4-5 for printed wiring board. • Refer to page 4-43 for waveforms. 12345678

CD-264 BOARD CCD IMAGER(CCD BLOCK) NO MARK:STILL/PB MODE SIGNAL PATH A S :STILL MODE VIDEO SIGNAL-REF.NO.:3000 SERIES- P :PB MODE AUDIO XX MARK:NO MOUNT CHROMA Y Y/CHROMA SIGNAL REC PB

CN101 23P

B167Q102CCD_GND 1 2SC4178-F13F14-T1 BUFFER

CCD_OUT 2 CCD_GND 3 CCD_GND 4 S14.8/P0 C115 V25210pCH V4 6 R107 V1A70V1B 8 C116

C 0.1u C113TO 16V XX

SY-59 BOARD(1/13) V3A9BCN101 V3B 10 R106 THROUGH THE NC 11 S-7.0/P0 S10.5/ 3300 FP-107 P0 FLEXIBLE VSHT 1212345678910 VSUB_CONT 13 (SEE PAGE IC102CAM_-7.5V 14 4-9) 3 CCD IMAGER CAM_15V 15 L102 C112 HDR_GND 16 100uH 10u 5

D 20VHDR_GND 17 B R109

TA 2.7 820 19 18 17 16 15 14 13 12 11 H2 18 S14.8/P0 RG 19 H1 20 R108 REG_GND 21 2.7 C110 0.1u REG_GND 22 16V B C105 REG_GND 23 1u 6.3V FB101 B 120uH C111

E 0.1uR104 16V1M F

C118 R11287650.1u 47 C1192200p L101BBTO CN103 3P 22uH SY-59 BOARD(9/13) R105 CN707 A_4.9V142700 S10.0/C106 P0 THROUGH THE A_GND 2 22u DC-67 HARNESS MIC_SIG 3 16V C109 B 0.1uC117 0 TA 16V (SEE PAGE 0.01u B16V B 4-29)

F Q101UN9213J-(K8).SO IC101 SWITCH

1234MIC_AMP R103 C102 100 1u 10V R102 B 1k

G CN102 2P

2 MIC GND C120 C107 C104 C103 MIC 10u 0.22u 47u 0.1u 1 MIC SIG 10V 10V 4V B C114 R101 C101 TA B TA XX 1200 0.1u MIC90116AABB

Precautions Upon Replacing CCD Imager

• The CD-264 board mounted as a repair part is not equipped with a CCD imager.

When replacing this board, remove the CCD imager from the

old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjust- ments for the camera section. • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts

nor exposed to strong light.

CCD IMAGER

CD-264 4-7 4-8 IC101 NJM2118V-TE2 0 MIC V+ V+ 0 EXT MIC V+ AMP OUT 4.1 +Vin AMP NFB 0 GND -Vin 0 IC102 ICX262AQ-13 S2.4/P0 H2 V4 S-7.0/P0 S2.6/P0 H1 V3A S-7.0/P0 S-7.2/P0 VL V3B S-0.1/P0 S9.9/P0 CSUB V2 S-0.1/P0 S9.8/P0 SUB V1A S-0.1/P0 GND V1B H1 S2.6/P0 TEST H2 S2.4/P0 TEST

RG

S13.2/P0 GND VDD VOUT S10.9/P0 S10.2/P0, DSC-F55V Schematic diagram and printed wiring board of the SY-59 board are not shown. Pages from 4-9 to 4-36 are not shown.,

DSC-F55V

1234567891012345678S105 S107 S104 S105 S106 S103 VOLUME/ VOLUME/ T W (LENS) PROGRAM PROGRAM

DISPLAY A AE ADJ AE ADJCONTROL SWITCH BLOCK(MS) (DIGITAL ZOOM) R106 R108 R110(DIGITAL ZOOM) (FWD) (REV) A CONTROL SWITCH BLOCK(HF) 2700 4700 (+) 6800 (-)

R103 1800 R10456k S101 D103 TLYU1002(TPX1,SONY) MENU (FLASH LAMP) RIGHTAPSETD101 TLGU1002(TPX1,SONY) R101 680 (POWER LAMP) CN702 6P UPDBDOWN S102 D+3.2V 1

B R101 TO680 MODE B SY-59 BOARD STB_LED 2 R1021800 LEFT C COMMON

D106 (13/13) TLSU1002(TPX1,SONY) PLAY STILL MOVIE CN702 REG_GND 3 R105 R107 R109(ACCESS LAMP) (SEE PAGE KEY_AD2 4 4700 6800 39k S106 4-33) KEY_AD1 5 R105 R102 R103 LCD 680 10k N.C 6 1800 R104 S102 BACK LIGHT2700 ON OFF S104 (FLASH) PROGRAM AE

C C

S101

POWER

ON/OFF S103 (1st) (SHUTTER) 1 2 STATIC_GND S107 (2nd) LND10134• CONTROL SWITCH BLOCK(HF) is replaced as a block.

D D So that this PRINTED WIRING BOARD is omitted.

LND101 CN703 15P STATIC_GND

E POWER_LED 1

ACCES_LED 2 CN101 10P XPWR_SW 3 10 Vss SIGNAL PATH D_3.2V49Vcc TO VIDEO SIGNAL SY-59 BOARD XCAM/PB_SW58SCLK AUDIO (13/13) MOVIE/XSTILL_SW67NC CN703 CHROMA Y Y/CHROMA SIGNAL SCLK76INT MEMORYSTICK (SEE PAGE RECINT85NC 4-33)

F DIO94DIO PB

VCC 10 3 NC BS 11 2 BS KEY_AD0 12 1 Vss XSHTR_SW 13 XSHTR_LOCK_SW 14 REG_GND 15 CONTROL SWITCH BLOCK(MS) is replaced as a block.

G So that this PRINTED WIRING BOARD is omitted. CONTROL SWITCH BLOCK MS / HF 4-37 4-38

D102 RD8.2UM-T1B2B3 D103 01ZA8.2(TPL3) D104 01ZA8.2(TPL3) D105 01ZA8.2(TPL3) D104 01ZAB.2(TPL3) D102 RD8.2UM-T1B2B3,

DSC-F55V For schematic diagram

• Refer to page 4-41 for printed wiring board. • Refer to page 4-43 for waveform. 12345678910 11 12 13 14 15 16 17 18 19 20 21

DD-143 BOARD A DC/DC CONVERTER(DD BLOCK)

-REF.NO.:2000 SERIES- R03618k

XX MARK:NO MOUNT ± 0.5%

0.2 T003 R037 Q011 DC/DC CONVERTER 68k C037

NO MARK:STILL/PB MODE ± 0.5% CPH3206-TL 2.2uSWITCHING B S :STILL MODE R038 D001182012 P :PB MODE 33k MA4ZD03001S0 4.0C010

± 0.5% 0.47u3227BC038

B412.2u3 6 B1 4 2012

R020 R082 R081R012 R016 R03923 R079 47k 220k 33k 47k 47k ± 0.5% ± 0.5% 10k453300 ± 0.5% R048 R076 R013 R021 XX 0 D006 R017 27k R032 MA4ZD03001S022k R046 C026 C028 -14.9 ± 0.5% 27k ± 0.5% 10k 0 C0252.2u 1u 2.2u Q032 CN004 40PBBC013 B3216 2SD2216J-QR(K8).SO2012 3216 120p D004 -14.3 R078 1 DD ON MA4ZD03001S0 B+ SWITCH 47k CH T001 -14.9 R001 C015 2 LCD ON 150k 3300p Q009 DC/DC CONVERTER14R077 ± 0.5% B CPH3106-PM-TL 3 CAM ONC Q033 100k SWITCHING23L016 12.818C044 2SB1462J-QR(K8).SO2.2u 100uH 4 BL ON5.3 B 2520 B+ SWITCH13.5 5 BL PWM R0552782014L013 100uH 13.5 6 BATT SIGR003 100k 4.003623C041 L012 7 GNDC016 1u 2.2u B 100uH Q030 D005 2520 UN9210J-(K8).SO 8 HI UNREG 16 15 14 13 12 11 10987654321B45MA4ZD03001S0 -14.9 -14.9 R004 3216 C054 C056C045 C059 9 BL LED ON 15k C004 1u 0.47u 1u 1u ± 0.5% B Q030,031 10 EVER+3.5V 0.001u 1 T002 Q025 B BC017 B B+ SWITCHB 3300p Q010 DC/DC CONVERTER C0401u 3216 UN9213J-(K8).SO 2012 2012 3216 11 PANEL+13.5VD B CPH3106-PM-TL B L009R008 SWITCHING 2012 S1.1/ 2.6 EMERGENCY27k DETECT 4.7uH 12 EVER+3.5V1 8 P0 2520 3.2R005 S2.3/P0 S5.0/ D007 4.9 13 PANEL+6.5V 15k -IN(C)5 Vcc(0)5.6.7 P6.3 MA4ZD03001S0 ± 0.5% S1.2/P0 6.2 R05627C051 Q031 -IN(E)5 OUT6 680 4.0 0 1u UN9110J-(K8).SO 14 CAM-7.5V R006 C005 S1.4/P0 5.0 R072 B 15 PANEL-15V 4700 R010 2700p FB5 OUT56800 3 6B 4.61418k ± 0.5% 1.2 C018 16 CAM+15V FB4 OUT4 5.6 2.2uB230 1.2 3216 4 5-IN(E)4 OUT3 C039 Q023 L010 L015 17 A+4.9V TO R007 1.7 S5.5/P6.2 1u CPH5601-TL 47uH 47uH C058 SY-59 BOARD(13/13) 18 A+4.9V 15k DTC4 IC001 Vss(0)4.5.6 Q005 B 2520 4.7u CN7052.5 2SB1462J-QR(K8).SO 3216 SWITCH 4.9 Q016 2520 C050 B± 0.5% R009 XX 2.5 4.0 CPH6301-TL 19 M+5V

E -IN(C)8 Vcc(0)3.4 1u 3216 THROUGH THE3.1 6.2 C020 XX B R062 C02921B+ SWITCH B2.5 DC/DC CONVERTER FP-109 FLEXIBLE

VREF OUT2-2 220 L004 4.9 20 M+5V 0.001u 22uH 3216 R011 47k B C046S1.4/P0.6 4.9 21 GND(M) GND IC001 R058 GND(0)2.3.4 XX 4C047 65600 L011 (SEE PAGE 6.2 MB3827PFV-G-BND-ER 4.5 Q003,005,006 C042 B XX 1 1uH2 22 GND(M)Vcc OUT2-1 DRIVER C035 4.7u S0/ R064 4-34) DD ON 3.1 3.8 5.6 0.2 2.2u 4.9 0

B

470k 23 D+1.8V CTL1-4.7 Vss(0)1-2 B P4.9B3453216 3 C052 CAM ON S3.1/P0 2.5 0.6 4.0 1.0 24 D+1.8V CTL5 Vcc(0)1-2 R067 4.7u1.5 LCD ON 3.1 6.2 R060 0.2 R069 C060 R070 C061 R074 47k B 25 PANEL+4.9V CTL6 OUT1-1 10k Q006 0.47u 100k 2012C001 10k 0.022uB03.2 2SC1621-T1B2B3 0.1u 100k B 26 D+3.2V CS1-6 VG(0)1 B R002 8.3 Q003 1.0 0 S0/P4.963039k 2SB1462J-QR(K8).SO Q021 27 D+3.2V

F CSCP OUT1-2 CPH5704-TL± 0.5% Q007 S3.1/P025R0652.0 2SB1462J-QR(K8).SO SWITCHING 33k 28 D+3.2V

VB OUT1-3 3.1 C002 0 C021 XX B R063 C030 R066 R068 L006 C003 0.22u 220 0.001u B L005 Q022 33k 10k 1uH 29 A+3.2V 0.1u B S3.8/ 22uH CPH5704-TL142520 B R059 P4.0 4.0215.0 30 A+3.2V3300 S4.4/ Q004,007,008 Q024 31 GND P4.6 DRIVER XP4213-TXE S5.5/ 32 A+3.2VC043 P6.2 C036 SWITCH2.2u 4.7u 33 GND 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 R061BBC053 10k 32163453216 4.7u 34 GND 4.0 B 35 GND

G 0.2 3216Q004 Q008

2SB1462J-QR(K8).SO 2SC1621-T1B2B3 36 GND 2.4 37 GND C024 Q012 L003 L007 38 GNDC006 3300p CPH5701-TL 22uH C032 1uHR022 100p B SWITCHING 2520 39 GND 18k CH Q019 S2.4/P0.1 4.7u B C049 C014 R057 CPH3403-TL 3216 4.7u 40 GND 100p 1k SWITCHING CH B3216 R053 4.0 18k C027 L0081uH

H C008 C009 R049 2.2u0.01u 6800p 2200 B LND002

R014 R018 R023 R027BBMECA GND 27k 22k 27k 22k R033 R040 C022 2200p B 18k 1k R050 R075 Q015 R024 1200 L014 XX 3.7 CPH5704-TL 1608 LND012 BT901 0 R030 R043 3.2 3.2 SWITCHING 3.2 1uH BATTERY 27k R051 MECA GNDR015 R019 R025 R028 15k ± 0.5% 3 2TERMINAL 47k XX 22k 39k ± 0.5% 22k R054 220 L002 ± 0.5% 4.0 4 10uH CN001 3P F002 R045 R047 C033 C048 C057 LND003 1.4A/32V 15k 4.827k513.2 4.7u 4.7u 4.7u ± 0.5% Q013BBMECA GNDBATT UNREG1B4.9 5.0 CPH5701-TL 3.2 3216

S C023 3216SWITCHING 3.2 1 4BATT SIG 2I 2.2u

LND004 BATT GND 3 R034 R041B0Q020 Q002 5600 0 XP4113-TXE255.0 MECA GND CPH3403-TL F003 ± 0.5% SWITCHING SWITCH 6 6.5 1.4A/32V630250LND013 D00300Q029 MECA GND R035 R042 RB521S-30-TE61 XP4213-TXED062 SWITCH MAZSO82008SO 39k 15k14± 0.5% ± 0.5% R031 LND011 F004 1.4A/32V MECA GND

J LND001 R0800

MECA GND CN002 3P D002F001 MA3XD21001S0 1.4A/32V SEIDEN GND 1 L001 FLASH 100uH UNIT ST GND 2MC-081 HARNESS ST UNREG 3 4.0 C034 4.7u

K IC002 B

ND901 (BACK-LIGHT) C019 DC/DC CONVERTER C031 33u 2.2u (STEP UP) 10V B IC002 3216 TA CN003 5P XC6372C351PR

B

BL UNREG 1 Note : The components identified by mark 0 or dotted

BACK

LIGHT BL GND 2 line with mark 0 are critical for safety. UNIT BL ON 3 (FOR LCD) DB-51

L HARNESS BL PWM 4 Replace only with part number specified.

BL LED ON 5 • FLASH UNIT is replaced as a block.

So that this PRINTED WIRING BOARD and SCHEMATIC DIAGRAM is omitted. DC/DC CONVERTER

4-39 4-40 DD-143 Q014 2SK1830-TE85L

SWITCH

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 0.5 RT DTC5 0.5 1.6 CT DTC6 1.7 1.7 DTC3 -IN(C)6 1.2 2.5 R029 27k -IN(E)3 FB6 1.2 1.3 FB3 -IN(E)6 1.7 1.2 C007 0.01u B FB2 OUT(A)6 1.2 1.2-IN(E)2 -IN(A)6 2.5 0 DTC2 DTC7 1.1 0.8 DTC1-4 +IN(E)7 1.6 2.5 DTC1-3 -IN(E)7-2 R044 12k 1.7 4.0 DTC1-1 -IN(E)7-1 1.2 2.4 -IN(E)1 FB7 C012 2200p B 1.2 0.5 FB1 XEB1-6 C011 0.0022u B GND(0)1 GND5.6.7 0.3 R052 27k RB1 RB7 6.4 0.5 OUT1-4 OUT7 0.2 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 4.0 4.0 4.5 0.73240.2513.85432S1.4/P0.6511233.9 3.9 R071 27k R073 10k 2 Q017 4.9 2SD2216J-QR(K8).SO B+ SWITCH 4.8,

DSC-F55V DD-143 (DC/DC CONVERTER) PRINTED WIRING BOARD

— Ref. No. DD-143 Board; 2,000 Series — For printed wiring boards • Refer to page 4-51 for parts location. FLASH UNIT • DD-143 board consists of multiple layers. However, only CD-264 the sides (layers) A and B are shown. (CCD IMAGER) • Chip parts Transistor Diode INVERTER TRANSFORMER UNITC65421343DD-143 (DC-DC CONVERTER) BE1233452112SY-59 CAMERA, CAMERA DSP, LCD DRIVE, TIMING GENERATOR,

There are few cases that the part printed on this VIDEO, SH DSP, AUDIO, LENS MOTOR DRIVE, HI CONTROL,

diagram isn’t mounted in this model. A/V OUT, USB, CONNECTOR

DC/DC CONVERTER

DD-143 4-41 4-42,

DSC-F55V

4-3. WAVEFORMS

CD-264 BOARD DD-143 BOARD

1 IC102 1,3 40µsec/div5V/div 1 IC001 1 OUT7 0.5µsec/div0.2V/div 8.2Vp-p NTSC:124µsec PAL : 125µsec 0.8Vp-p500kHz 2 40µsec/div IC102 4,6 5V/div 8.2Vp-p NTSC:124µsec PAL : 125µsec 3 IC102 0 700mVp-p NTSC:124µsec PAL : 125µsec 40µsec/div 0.5V/div 4 IC102 qf,ql 40µsec/div2V/div 7.5Vp-p NTSC:124µsec PAL : 125µsec 5 IC102 qd,w; 40µsec/div2V/div 7.5Vp-p NTSC:124µsec PAL : 125µsec 6 IC102 2 23.2Vp-p NTSC:33.3msec 10msec/div PAL : 40msec 10V/div 7 IC102 5 10msec/div 10V/div 23.2Vp-p NTSC:33.3msec PAL : 40msec 8 IC102 qs 40nsec/div 2V/div 4.8Vp-p NTSC:54.3nsec PAL : 54.7nsec

WAVEFORMS

4-43 CD-264, DD-143,

DSC-F55V Waveforms and parts location of the SY- 4-4. MOUNTED PARTS LOCATION

59 board are not shown. CD-264 BOARD (SIDE A) CD-264 BOARD (SIDE B)

Pages from 4-45 to 4-47 are not shown. C101 C-3 CN103 A-1

C102 C-3 C103 D-3 IC102 A-2 C104 C-3 C105 D-2 C106 D-2 C107 D-2 C109 D-2 C110 C-2 C111 C-2 C112 D-2 C113 D-2 C114 C-3 C115 D-2 C116 D-2 C117 C-2 C118 D-1 C119 D-2 C120 D-3 CN101 D-1 CN102 D-3 FB101 D-2 IC101 D-3 L101 D-3 L102 D-2 Q101 D-2 Q102 D-2 R101 D-3 R102 C-3 R103 C-3 R104 C-2 R105 D-2 R106 D-2 R107 D-2 R108 C-2 R109 C-1 R112 C-2

PARTS LOCATION

CD-264 4-48,

DSC-F55V DD-143 BOARD (SIDE A) DD-143 BOARD (SIDE B)

C043 C-2 C001 C-4 Q015 A-4 C046 C-2 C002 C-4 Q019 B-4 C047 B-2 C003 C-4 Q020 A-4 C051 B-2 C004 C-5 Q021 B-4 C052 B-2 C005 C-4 Q025 B-5 C054 C-2 C006 C-4 Q029 C-5 C056 C-1 C007 C-5 Q032 C-5 C059 C-1 C008 C-4 C060 C-2 C009 C-4 R001 C-5 C061 B-2 C010 C-5 R002 C-4 C011 B-5 R003 C-5 CN001 C-2 C013 B-5 R004 C-5 CN002 C-1 C015 A-4 R005 C-5 CN003 C-1 C016 A-4 R006 C-4 CN004 B-1 C017 B-4 R007 C-4 C018 A-4 R008 C-5 D062 C-2 C019 A-5 R009 C-4 C020 B-4 R010 C-4 F001 C-2 C021 B-4 R011 C-4 F002 C-2 C022 A-3 R012 C-5 F003 C-2 C023 A-3 R013 C-5 F004 C-2 C024 A-3 R014 C-3 C025 A-5 R015 C-3 L001 A-1 C026 A-5 R016 C-5 L002 A-2 C027 A-4 R017 C-5 L003 A-2 C028 A-5 R018 C-4 L004 B-2 C029 B-4 R019 C-3 L005 B-2 C030 B-4 R020 C-5 L008 A-1 C031 B-5 R021 C-5 L009 B-1 C032 B-4 R022 C-4 L011 B-1 C033 A-4 R023 C-4 L012 B-1 C034 A-5 R024 C-3 L013 C-1 C035 B-4 R025 C-3 L014 A-1 C036 B-4 R027 C-3 L016 C-1 C037 A-5 R028 C-3 C038 A-5 R029 C-5 Q016 B-2 C039 B-4 R030 C-3 Q017 B-1 C040 A-4 R031 C-5 Q022 B-2 C041 A-4 R032 C-5 Q023 C-2 C042 B-5 R033 C-3 Q024 C-2 C044 A-4 R034 C-3 Q030 C-1 C045 A-4 R035 C-4 Q031 C-1 C048 A-5 R036 C-5 Q033 C-1 C049 B-5 R037 C-5 C050 C-5 R038 C-5 R064 B-2 C053 B-5 R039 C-5 R065 C-2 C057 A-5 R040 C-3 R066 C-2 C058 C-5 R041 C-3 R067 C-2 C102 B-3 R042 C-4 R068 C-1 C104 B-3 R043 C-3 R069 C-2 R044 C-4 R070 C-2 D001 A-4 R045 C-3 R073 B-2 D002 A-5 R046 B-5 R074 B-2 D003 A-3 R047 B-3 D004 A-4 R048 B-5 T001 A-2 D005 A-4 R049 C-4 T002 A-2 D006 A-4 R050 B-4 T003 A-1 D007 A-4 R051 B-3 R052 B-5 IC001 C-4 R053 B-4 IC002 B-5 R054 A-3 R055 A-4 L006 B-5 R056 B-4 L007 B-5 R057 B-3 L010 C-5 R058 B-4 L015 C-5 R059 B-4 R060 B-4 Q002 C-5 R061 B-4 Q003 B-4 R062 B-4 Q004 B-4 R063 B-4 Q005 B-4 R071 B-5 Q006 B-4 R072 B-5 Q007 B-3 R075 A-5 Q008 B-3 R076 C-5 Q009 A-4 R077 C-5 Q010 A-4 R078 C-5 Q011 A-5 R079 C-5 Q012 A-3 R080 C-4 Q013 A-3 R081 B-5 Q014 C-4 R082 C-5

PARTS LOCATION

4-49E DD-143,

DSC-F55V SECTION 5 ADJUSTMENTS

1. Before starting adjustment

EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair) PC PC (Machine after a board is replaced) Save the EVR data Download the saved to a personal computer. data to a machine. Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it. (Former board) (New board) Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or installed, save the data from the same model of the same destination, and download it. (Machine to be repaired) PC (Machine to be repaired) Download the data. Save the data. (The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 5-1, 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Board Block Mounted parts replace replacement replacement ment Adjustment Adjustment Section Initialization of B, D, Initialization of D page datazzE, F, 7 page data Initialization of B, E, F, 7 page datazzVideo Video output level adj. zzzzzHALL adj. zzzzFlange back adj. zzzzFNo. standard data InputzzzzMechanical shutter adj. zzzzLight level adj. and ND shutter checkzzzzzMixed color cancel adj. zzzzzCamera AWB standard data inputzzzzzAuto white balance adj. zzzzzColor reproduction adj. zzzzzStrobe white balance Adj. zzzzzCCD black defect compensationzzzCCD white defect compensationzzzLCD initial data inputzzVCO adj. zzzzDrange adj. zzzzBright adj. zzzzLCD Contrast adj. zzzzColor adj. zzzzV-COM level adj. zzzzV-COM adj. zzzzzWhite balance adj. zzzzzzSystem control Battery end adj. z z *1: When replacing the Flash unit, reset the data of page: D, address: 67 to “00”. (Refer to “Emergency Memory Address of Flash Unit” of “5-2. SERVICE MODE”.) Table. 5-1-1. 5-2 Lens device Flash unit *1 LCD block LCD901 LCD block Back light unit CD-264 board IC102 (CCD imager) SY-59 board IC102 (S/H, AGC, A/D) SY-59 board IC301 (CAMERA DSP) SY-59 board IC204 (EVR) SY-59 board IC651 (Video amp.) SY-59 board IC803 (RGB decoder) SY-59 board IC801 (EVR) SY-59 board IC901 (Timing generator) SY-59 board (COMPLETE) SY-59 board IC405 EEPROM SY-59 board IC507 EEPROM, 5-1. ADJUSTMENTS 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check J-1 Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check J-2 Pattern box PTB-450 J-6082-200-A J-3 Color chart for pattern box J-6020-250-A Adjustment remote commander (RM-95 upgraded). J-4 J-6082-053-B (Note 1) J-5 Siemens star chart J-6080-875-A For checking the flange back J-6 Clear chart for pattern box J-6080-621-A For connecting the adjustment remote commander J-7 CPC-9 jig (Note 2) J-6082-393-C For adjusting the LCD block J-8 Mini pattern box J-6082-353-B For adjusting the flange back J-9 Personal computer with Windows95/98 installed For checking the recorded picture Picture management software J-10 Picture Gear Ver.3.2 Lite For checking the recorded picture Note 1: If the micro processor IC in the adjustment remote commander is Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, not the new micro processor (UPD7503G-C56-12), The pages because it cannot operate the adjustment remote commander. cannot be switched. In this case, replace with the new micro processor (8-759-148-35). J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 J-10 Fig. 5-1-1. 5-3, 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Pattern box Note 2: When performing only the adjustments, the boards need not be disassembled. 1) Connect the equipment for adjustments according to Fig. 5-1-5. 2) Connect the Adjustment remote commander to SY-59 board CN704 via CPC-9 jig (J-6082-393-C, Note3). (See Fig. 5-1- 3.) To operate the adjustment remote commander, connect the power supply terminal of CPC-9 jig to the DC power supply About 32 cm (6.0 to 7.2Vdc). Note 3: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 4: Setting the “Forced Power ON Mode (Forced STILL Mode)” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjustment remote commander. The above procedure will enable the power (STILL mode) to be turned on with MS block removed. After completing adjustments, be sure to exit the “Forced Power ON Mode”. Front of the lens Note 5: Setting the “Forced Power ON Mode (Forced PLAY Mode)” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 02, and press the PAUSE Fig.5-1-2. button of the adjustment remote commander. The above procedure will enable the power (PLAY mode) to be turned on. After completing adjustments, be sure to exit the “Forced Power ON Mode”. Note 6: Exiting the “Forced Power ON Mode” 1) Select page: 0, address: 01, and set data: 01. Capacitor 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjustment remote commander. 3) Select page: 0, address: 01, and set data: 00. Short jig (See page 5) 1-1-3. Discharging of the strobe power supply The capacitor which is used as power supply of strobe is charged with 200V to 300V voltage. Discharge this voltage before starting R: 1kΩ 1W adjustments in order to protect service engineers from electric shock (Parts code: during adjustment. 1-215-869-11) Discharge procedure 1. Press the FLASH button (HF block) and turn off the FLASH Flash Unit LED (HF block). 2. Fabricate the short jig as shown in Fig. 5-1-4 locally by yourself. Fig.5-1-4. Connect the short jig to the positive (+) and negative (-) terminal of the flash voltage charge capacitor. Allow ten seconds to discharge the voltage. SY-59 board CN704 18 Conductor side 18 pin flexible board (Note) P Note: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. (Fig 1) Remove the check cover by rotating the metal bar in the direction of the arrow of ø1.6 or less centering around the point “P”. Note: Do not reuse the check cover that is once removed. Fig.5-1-3. 5-4,

VIDEO

Terminated at 75Ω (Yellow) Vector scope Color monitor

AUDIO

(Black) CN002 CN003 CN701 CN101 CN001 CN703 CN702 CN201 J951 DD-143 SY-59 A/V OUT BOARD BOARD CN004 CN706 CN901 CN707 CN704 18 1 DC power supply (6.0 to 7.2Vdc)

BATTERY

terminal 18 pins CPC-9 jig (J-6082-393-C)(Note) Adjustment remote commander 12 pins LANC jack AC power adaptor

Fig.5-1-5.

Note : The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. 5-5, 1-1-4. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments. 1. DEMO MODE (SETUP menu) ...OFF 7. PROGRAM AE (HF block) ... AUTO 2. DIGITAL ZOOM (MS block) ... Wide end (No mark indicated on LCD) 3. WHITE BALANCE (CAMERA menu) ... AUTO 8. FOCUS (Menu) ... AUTO 4. FLASH LEVEL (CAMERA menu) ... NORMAL (No mark indicated on LCD) 5. EXPOSURE (CAMERA menu) ... 0EV 9. DISPLAY (HF block) ...OFF 6. P. EFFECT (EFFECT menu) ...OFF 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame

H

C C=D D CRT picture frame

V

A B A=BBAFig. b (monitor TV picture) Fig. a Enlargement Video terminal output waveform Difference in level Adjust the camera zoom and direction toBAobtain the output waveform shown in Fig. a and the monitor TV display shown in Fig. b. Fig. 5-1-6. 3. Subjects 1) Color bar chart (Color reproduction adjustment frame) When performing adjustments using the color bar chart, adjust the picture frame as shown in Fig. 5-1-6. (Standard picture White frame) 2) Clear chart (Color reproduction adjustment frame) 841mm Remove the color bar chart from the pattern box and insert a Black clear chart in its place. (Do not perform zoom operations during this time.) 3) Flange back adjustment chart 1189mm Make the chart shown in Fig. 5-1-7 using A0 size (1189 mm × 841 mm) black and white vellum paper. Fig. 5-1-7. Note: Use matte vellum paper bigger than A0, and make sure the edges of the black and white paper joined together are not rough. 5-6 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA 1-2-1. INITIALIZATION OF D PAGE DATA 1. Initializing the D Page Data 3. D Page Table Note: If the D page data has been initialized, the following adjustments Note1: Fixed data-1: Initialized data. (Refer to “1. Initializing the D Page need to be performed again. Data”.) 1) Modification of D page data Fixed data-2: Modified data. (Refer to “2. Modification of D Page 2) LCD system adjustments Data”.) 3) Battery end adjustments Address Initial value Remark Adjusting page D 00 to 0F Adjusting Address 10 to EF 10 00 Test mode 11 to 42 Fixed data-1 (Initialized data) Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 43 Fixed data-2 2) Select page: 2, address: 03, and set data: 01. (Modified data. Copy the data built in 3) Select page: 2, address: 00, and set data: 2D. the same model.) 4) Select page: 2, address: 01, set data: 2D, and press the PAUSE 44 to 61 Fixed data-1 (Initialized data) button of the adjustment remote commander. 62 Fixed data-2 5) Select page: 2, address: 02, and check that the data changes to 63 (Modified data. Copy the data built in “01”. 6) Perform “Modification of D Page Data”. the same model.) 64 to 66 Fixed data-1 (Initialized data) 2. Modification of D Page Data 67 00 Flash unit emergency If the D page data has been initialized, change the data of the “Fixed 68 to 6B Fixed data-1 (Initialized data) data-2” address shown in the following table by manual input. 6C 00 Recording counter Modifying Method: 6D 00 1) Before changing the data, select page: 0, address: 01, and set 6E 00 data: 01. 6F 00 Recording counter/MC CAM (SY-59 2) New data for changing are not shown in the tables because board IC501) emergency they are different in destination. When changing the data, copy 70 to 7C Fixed data-1 (Initialized data) the data built in the same model. 7D Fixed data-2 Note: If copy the data built in the different model, the camera may not operate. 7E to 89 Fixed data-1 (Initialized data) 3) When changing the data, press the PAUSE button of the 8A Fixed data-2 adjustment remote commander each time when setting new 8B (Modified data. Copy the data built in data to write the data in the non-volatile memory. the same model.) 4) Check that the data of adjustment addresses is the initial value. 8C to 8F Fixed data-1 (Initialized data) If not, change the data to the initial value. 90 80 Battery end adj. Processing after Completing Modification of D Page data 91 88 1) Select page: 2, address: 00, and set data: 29. 92 AD 2) Select page: 2, address: 01, and set data: 29, and press the 93 C2 PAUSE button of the adjustment remote commander. 94 CD 95 to 97 Fixed data-1 (Initialized data) 98 Fixed data-2 99 (Modified data. Copy the data built in 9A the same model.) 9B 9C 9D 9E 9F A0 A1 A2 Fixed data-1 (Initialized data) A3 Fixed data-2 A4 Fixed data-1 (Initialized data) A5 Fixed data-2 A6 to CF Fixed data-1 (Initialized data) D0 BC Bright adj. (LCD) D1 80 Color adj. (LCD) D2 B9 White balance adj. (LCD) D3 B7 5-7, 1-2-2. Initializing the B, E, F, 7 Page Data Address Initial value Remark 1. Initializing the B, E, F, 7 Page Data D4 BE Contrast adj. (LCD) Note1: If “Initializing the B, E, F, 7 Page Data” is performed, all data of D5 C8 D range adj. (LCD) the B page, E page, F page and 7 page will be initialized. (It is D6 7C V-COM level adj. (LCD) impossible to initialize a single page.) D7 80 VCO adj. (LCD) (NTSC) Note2: If the B, E, F, 7 Page data has been initialized, “Modification of B, E, F, 7 Page Data” and following adjustments need to be performed D8 74 V-COM adj. (LCD) again. D9 to DC Fixed data-1 (Initialized data) 1) Video system adjustments DD 88 VCO adj. (LCD) (PAL) 2) Camera system adjustments DE to FF Fixed data-1 (Initialized data) Adjusting page F Table. 5-1-2. Adjusting Address 10 to FF Adjusting page 7 Adjusting Address 00 to FF Adjusting page E Adjusting Address 00 to FF Adjusting page B Adjusting Address 00 to FF Initializing Method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 03, and set data: 01. 3) Select page: 6, address: 00, and set data: 2D. 4) Select page: 6, address: 01, set data: 2D, and press the PAUSE button. 5) Select page: 6, address: 02, and check that the data changes to “01”. 6) Perform “Modification of B, E, F, 7 Page Data”. 2. Modification of B, E, F, 7 Page Data If the B, E, F, 7 Page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camera may not operate. 3) When changing the data, press the PAUSE button of the adjustment remote commander each time when setting new data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. Processing after Completing Modification of B, E, F, 7 Page data 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, and set data: 29, and press the PAUSE button of the adjustment remote commander. 5-8, 3. F Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Address Initial value Remark Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 4F to 58 Fixed data-1 (Initialized data) Page Data”.) 59 00 AWB standard data input 5A 14 Mechanical shutter adj. Address Initial value Remark 5B Fixed data-1 (Initialized data) 00 to 0F 5C 63 Color reproduction adj. 10 to 13 Fixed data-1 (Initialized data) 5D 83 14 10 Flange back adj. 5E 03 15 00 5F E9 16 10 60 to 63 Fixed data-1 (Initialized data) 17 01 64 10 Strobe white balance adj. 18 11 65 61 Video output level adj. 19 00 66 61 1A 00 67 to 68 Fixed data-1 (Initialized data) 1B 00 69 01 Strobe white balance adj. 1C 00 6A A3 1D 00 6B B4 1E 00 6C 0B Mechanical shutter adj. 1F 00 6D C2 20 20 6E 09 21 20 6F 42 22 20 70 06 23 04 71 C2 24 0A 72 05 25 00 73 C2 26 85 Light level Adj. 74 04 27 Fixed data-1 (Initialized data) 75 C2 28 94 Light level Adj. 76 33 29 47 F No. standard data input 77 33 2A 41 78 33 2B 3D 79 33 2C 3D 7A 33 2D Fixed data-1 (Initialized data) 7B 33 2E 80 Hall adj. 7C 33 2F 93 7D 33 30 to 33 Fixed data-1 (Initialized data) 7E 33 34 15 Hall adj. 7F 33 35 7C 80 00 Auto white balance adj. 36 to 39 Fixed data-1 (Initialized data) 81 to 9F Fixed data-1 (Initialized data) 3A 2F AWB standard data input A0 00 Mixed color cancel adj. 3B 37 A1 00 3C 40 A2 00 3D D0 A3 00 3E Fixed data-1 (Initialized data) A4 to FF Fixed data-1 (Initialized data) 3F B5 Auto white balance adj. Table. 5-1-3. 40 43 41 03 Color reproduction adj. 42 E9 43 63 44 83 45 D5 46 FE 47 73 48 45 49 to 4C Fixed data-1 (Initialized data) 4D 27 Strobe white balance adj. 4E 77 5-9, 4. 7 Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Address Initial value Remark Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 93 FF CCD white defect compensation Page Data”.) 94 0F 95 FF Address Initial value Remark 96 0F 00 to 5F Fixed data-1 (Initialized data) 97 FF 60 0F CCD black defect compensation 98 0F 61 FF 99 FF 62 0F 9A 0F 63 FF 9B FF 64 0F 9C 0F 65 FF 9D FF 66 0F 9E 0F 67 FF 9F FF 68 0F A0 0F 69 FF A1 FF 6A 0F A2 0F 6B FF A3 FF 6C 0F A4 to FF Fixed data-1(Initialized data) 6D FF Table. 5-1-4. 6E 0F 6F FF 70 0F 71 FF 72 0F 73 FF 74 0F 75 FF 76 0F 77 FF 78 0F 79 FF 7A 0F 7B FF 7C 0F 7D FF 7E 0F 7F FF 80 0F 81 FF 82 0F 83 FF 84 0F 85 FF 86 0F 87 FF 88 0F CCD white defect compensation 89 FF 8A 0F 8B FF 8C 0F 8D FF 8E 0F 8F FF 90 0F 91 FF 92 0F 5-10, 5. E Page Table 6. B Page Table Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Note: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”.) Page Data”.) Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7 Page Data”.) Page Data”.) Address Remark Address Remark 00 to FF Fixed data-1 (Initialized data) 00 Fixed data-2 (Modified data. Copy the data built in Table. 5-1-5. the same model.) 01 to FF Fixed data-1 (Initialized data) Table. 5-1-6. 5-11, 1-3. VIDEO SYSTEM ADJUSTMENTS 1. Video Output Level Adjustment (SY-59 board) Adjust the sync level and burst level of the composite video signal output. Mode PLAY Signal Arbitrary Measurement Point Video terminal of AV OUT jack (75 Ω terminated) Measuring Instrument Oscilloscope Adjustment Page F Adjustment Address 65, 66 Specified Value Sync level: A=286 ± 5 mV (NTSC mode) A=300 ± 5 mV (PAL mode) Burst level: B=286 ± 5 mV (NTSC mode) B=300 ± 5 mV (PAL mode) Y level: C=714 + 20– 40 mV (NTSC mode) C=700 + 20 mV (PAL mode) – 40 Menu setting: 1) VIDEO OUT of SET UP menu ... NTSC (NTSC mode) ... PAL (PAL mode) Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: 04. 3) Select page: F, address: 65, change the data and set the sync level (A) to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: F, address: 66, change the data and set the burst level (B) to the specified value. 6) Press the PAUSE button. 7) Check that the Y level (C) satisfied the specified value. 8) Select page: 5, address: F1, and set data: 00. 9) Select page: 0, address: 01, and set data: 00.

C B A H

Fig. 5-1-8. 5-12, 1-4. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments, check that the specified values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. 1. HALL Adjustment For detecting the position of the lens iris, adjust the hall AMP gain and offset. Mode STILL Subject All black (Cover the lens with a black cap) Measurement Point Display data of page 1 (Note 1) Measuring Instrument Adjustment remote commander Adjustment Page F Adjustment Address 2E, 2F, 34, 35 Specified Value 13 to 17 during IRIS OPEN 7B to 7F during IRIS CLOSE Note 1: Displayed data of page 1 of the adjustment remote commander. 1 : 00 : XX Display data Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: 01, set data: 00, and press the PAUSE button. Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 94, and set data: 15. 3) Select page: 6, address: 95, and set data: 7D. 4) Select page: 6, address: 01, set data: 6D, and press the PAUSE button of the adjustment remote commander. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 2E, 2F, 34 and 35.) 5) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 0, address: 03, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button. 3) Select page: 1, and check that the display data (Note1) during IRIS OPEN satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the display data during IRIS CLOSE satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 94, and set data: 00. 3) Select page: 6, address: 95, and set data: 00. 4) Select page: 0, address: 03, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. 5-13, 2. Flange Back Adjustment (Using Minipattern Box) The inner focus lens flange back adjustment is carried out Adjusting method: automatically. In whichever case, the focus will be deviated during 1) Install the minipattern box so that the distance between it and auto focusing/manual focusing. the front of the lens of the camera is less than 3cm. Mode STILL 2) Make the height of the minipattern box and the camera equal. Subject Siemens star chart with ND filter for 3) Check that the output voltage of the regulated power supply is the minipattern box (Note 1) the specified voltage. 4) Select page: 0, address: 01, and set data: 01. Measurement Point Check operation on TV monitor 5) Check that the center of the Siemens star chart and the center Measuring Instrument of the exposure screen coincide. Adjustment Page F 6) Check that the data of page: F, address: 14 to 25 is the initial Adjustment Address 14 to 25 value (See table below). Address Data Address Data Address Data Note 1: Dark Siemens star chart. 14 10 1B 00 22 20 Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: 01, set data: 00, and press the PAUSE button. 15 00 1C 00 23 04 16 10 1D 00 24 0A Preparations before adjustments: 17 01 1E 00 25 00 The minipattern box is installed as shown in the following figure. 18 11 1F 00 Note: The attachment lenses are not used. Specified voltage: The specified voltage varies according to the 19 00 20 20 minipattern box, so adjust the power supply 1A 00 21 20 output voltage to the specified voltage written on the sheet which is supplied with the 7) Select page: 6, address: 01, set data: 13, and press the PAUSE minipattern box. button of the adjustment remote commander. 8) Select page: 6, address: 01, set data: 27, and press the PAUSE Below 3 cm button. (The adjustment data will be automatically input to page: F, Minipattern box addresses: 14 to 25.) 9) Select page: 6, address: 02, and check that the data is changed Camera to “01”. Camera Processing after Completing Adjustments: table 1) Select page: 6, address: 01, set data: 00, and press the PAUSE Regulated power supply button. Output voltage : Specified voltage ±0.01Vdc 2) Perform “Flange Back Check”. Output current : more than 3.5A Red (+) Black (–) Yellow (SENS +) White (SENS –) Need not connected Black (GND) Fig. 5-1-9. 5-14, 3. Flange Back Adjustment 4. Flange Back Check (Using Flange Back Adjustment Chart) Mode STILL The inner focus lens flange back adjustment is carried out Subject Siemens star automatically. In whichever case, the focus will be deviated during (2.0 m from the front of the lens) auto focusing/manual focusing. (Luminance : approx. 200 lux) Measurement Point Mode STILL Check operation on TV monitor Measuring Instrument Subject Flange back adjustment chart (2.0 m from the front of the lens) Specified Value The lens is focused. (Luminance: 350 ± 50 lux) Checking method: Measurement Point Check operation on TV monitor 1) Place the Siemens star 2.0m from the front of the lens. Measuring Instrument 2) To open the IRIS, decrease the luminous intensity to the Adjustment Page F Siemens star up to a point before noise appear on the image. Adjustment Address 14 to 25 3) Select page: 5, address: F1, and set data: FF. 4) Select page: 6, address: 2C, and set data: 02. Note: If the data of page: 6, address: 02 is “01”, select page: 6, address: 5) Observe the TV monitor and check that the lens is focused. 01, set data: 00, and press the PAUSE button. Processing after Completing Adjustments: Adjusting method: 1) Select page: 6, address: 2C, and set data: 00. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: 00. 2) Check that the center of the chart for the flange back adjustment and the center of the exposure screen coincide. 3) Check that the data of page: F, address: 14 to 25 is the initial 5. F No. Standard Data Input value (See table below). Compensate the unevenness of the iris meter sensitivity. Address Data Address Data Address Data Mode STILL 14 10 1B 00 22 20 Subject Clear chart (All white) 15 00 1C 00 23 04 Adjustment Page F 16 10 1D 00 24 0A Adjustment Address 29 to 2C 17 01 1E 00 25 00 Note 1: If the data of page: 6, address: 02 is “01”, select page: 6, address: 18 11 1F 00 01, set data: 00, and press the PAUSE button. 19 00 20 20 Note 2: After the power is turned on, this adjustment can be done only 1A 00 21 20 once. Adjusting method: 4) Select page: 6, address: 01, set data: 13, and press the PAUSE 1) Shoot the clear chart. button of the adjustment remote commander. 2) Select page: 0, address: 01, and set data: 01. 5) Select page: 6, address: 01, set data: 15, and press the PAUSE 3) Select page: E, address: 51, after noting down the data, set button. data: FF, and press the PAUSE button. (The adjustment data will be automatically input to page: F, 4) Select page: 6, address: 01, set data: BB, and press the PAUSE addresses: 14 to 25.) button of the adjustment remote commander. 6) Select page: 6, address: 02, and check that the data is changed (The F No. standard data input is performed and the adjustment to “01”. data is stored in page: F, address: 29 to 2C.) Processing after Completing Adjustments: 5) Select page: 6, address: 02, and check that the data is “01”. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 2) Perform “Flange Back Check”. button. 2) Select page: E, address: 51, set the data noted down at step 3), and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00. 5-15, 6. Mechanical Shutter Adjustment Adjust the period which the mechanical shutter is closed, and compensate the exposure. Mode STILL Subject Clear chart (All white) (10 cm from the front of the lens) Adjustment Page F Adjustment Address 5A, 6C to 7F Note: 1 If the data of page: 6, address: 02 is “01”, select page: 6, address: 01, set data: 00, and press the PAUSE button. Note: 2 Install the clear chart at a distance of about 10 cm from the front of the lens. (It is recommended.) Adjusting method: 1) Shoot the clear chart. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: 6, address: 01, set data: AD, and press the PAUSE button of the adjustment remote commander. (The mechanical shutter adjustment is performed and the adjustment data is stored in page: F, address: 5A, 6C to 7F.) 4) Select page: 6, address: 02, and check that the data changes to “01”. 5) Select page: 6, address: AB, and check the data. 00: Normal 01 to FF: Defective Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 0, address: 01, and set data: 00. 5-16, 7. Picture Frame Setting Mode STILL Check on an oscilloscope Subject Color bar chart (Color reproduction adjustment 1. Horizontal period frame) About 32 cm from the front of A=B C=D the lensBCMeasurement Point Video output terminalADMeasuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Note 1: Display data of page 1 of the adjustment remote commander. 1 : XX : XX XL or YL data XH or YH data Setting method: 1) Select page: 5, address: F1, and set data: FF. 2) Adjust the camera direction, and set the picture frame to the specified position. 3) Mark the position of the picture frame on the monitor display, and adjust the picture frame to this position in following adjustments using “Color reproduction adjustment frame”. Fig. 5-1-10. 4) Select page: 0, address: 03, and set data: 18. 5) Select page: 1, and note down the XH data and XL data. (Note1) 2. Vertical period 6) Select page: 0, address: 03, and set data: 22. 7) Select page: 1, and note down the YH data and YL data. (Note1) E E=F F 8) Select page: 5, address: F1, and set data: 00. How to reset the focus when they deviated: If the focus deviated due to some reason, reset them in the following method. V Fig. 5-1-11. 1) Select page: 6, address: 90, and set data: XL. (Note 2) 2) Select page: 6, address: 91, and set data: XH. (Note 2) Check on the monitor TV (Underscanned mode) 3) Select page: 6, address: 92, and set data: YL. (Note 3) 4) Select page: 6, address: 93, and set data: YH. (Note 3) 5) Select page: 6, address: 6C, and set data: 01. 6) Select page: 6, address: 01, set data: 79, and press the PAUSE button and wait for 1 second. 7) Select page: 6, address: 2C, and set data: 01. 8) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Note 2: The data noted down at step 5) .of the “Setting method”. Note 3: The data noted down at step 7) .of the “Setting method”. Color bar chart picture frame Monitor TV picture frame Fig. 5-1-12. 5-17, 8. Light Level Adjustment and ND Shutter Check 9. Mixed Color Cancel Adjustment Adjust the standard LV value. Perform the mixed color cancel adjustment using the each data of Mode STILL the color bars. Subject Clear chart Mode STILL (Color reproduction adjustment frame) Subject Color bar chart Measurement Point Display data of page 1 (Note 2) (Color reproduction adjustment frame) Measuring Instrument Adjustment remote commander Adjustment Page F Adjustment Page F Adjustment Address A0 to A3 Adjustment Address 26, 28 Note 1: This adjustment should be carried out upon completion of “Light Specified Value 0FE0 to 1020 Level Adjustment and ND Shutter Check”. Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: Note 1: If the data of page: 6, address: 02 is “01”, select page: 6, address: 01, set data: 00, and press the PAUSE button. 01, set data: 00, and press the PAUSE button. Note 2: Displayed data of page 1 of the adjustment remote commander. Adjusting method: 1 : XX : XX 1) Select page: 0, address: 01, and set data: 01. Display data 2) Check that the picture frame is set to the specified position. (Refer to “8. Picture Frame Setting”.) Adjusting method: 3) Select page: 6, address: 01, set data: D7, and press the PAUSE 1) Select page: 0, address: 01, and set data: 01. button of the adjustment remote commander. 2) Select page: 6, address: 01, set data: 0D, and press the PAUSE 4) Select page: 6, address: 01, set data: D5, and press the PAUSE button of the adjustment remote commander. button. (The light level adjustment is performed and the adjustment (The mixed color cancel adjustment is performed and the data is stored in page: F, address: 26, 28.) adjustment data is stored in page: F, address: A0 to A3.) 3) Select page: 6, address: 02, and check that the data is “01”. Note: Observe the TV monitor and check that a vertical line is indicated • AE level Check inside each color zone. 4) Select page: 0, address: 03, and set data: 06. 5) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: 1, and check that the display data (Note2) satisfies the AE level 1 specified value. Processing after Completing Adjustments: 1) Select page: 6, address: 01, and set data: 00, and press the Processing after Completing Adjustments: PAUSE button. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 2) Select page: 0, address: 01, and set data: 00. button. 2) Select page: 0, address: 03, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. 5-18, 10. Auto White Balance Standard Data Input 11. Auto White Balance Adjustment Adjust the white balance standard data at 3200 K. Adjust to the proper auto white balance output data. Mode STILL If it is not correct, auto white balance and color reproducibility will be poor. Subject Clear chart (Color reproduction adjustment frame) Mode STILL Adjustment Page F Subject Clear chart (Color reproduction adjustment frame) Adjustment Address 3A to 3D, 59 Filter Filter C14 for color temperature Note 1: If the data of page: 6, address: 02 is “01”, select page: 6, address: correction 01, set data: 00, and press the PAUSE button. Measurement Point Display data of page 1 (Note 2) Note 2: After the power is turned on, this adjustment can be done only once. Measuring Instrument Adjustment remote commander Adjustment Page F Adjusting method: Adjustment Address 3F, 40, 80 1) Select page: 0, address: 01, and set data: 01. Specified Value R ratio: 28E0 to 2A20 2) Select page: 6, address: 01, set data: 11, and press the PAUSE B ratio: 5E60 to 5FA0 button of the adjustment remote commander. 3) Select page: 6, address: 01, set data: 0B, and press the PAUSE Note 1: This adjustment should be carried out upon completion of “Auto button. White Balance Standard Data Input”. (The auto white balance standard data input is performed and Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: the adjustment data is stored in page: F, address: 3A to 3D, 59) 01, set data: 00, and press the PAUSE button. 4) Select page: 6, address: 02, and check that the data is “01”. Note 3: After the power is turned on, this adjustment can be done only once. Processing after Completing Adjustments: Note 4: Displayed data of page 1 of the adjustment remote commander. 1) Select page: 6, address: 01, and set data: 00, and press the 1 : XX : XX PAUSE button. Display data 2) Select page: 0, address: 01, and set data: 00. Adjusting method: 1) Place the C14 filter for color temperature correction on the lens. 2) Select page: 0, address: 01, and set data: 01. 3) Select page: F, address: 49 to 4C, and note down the data of each address. 4) Input the following data to page: F, addresses: 49 to 4C. Address 49 4A 4B 4C Data 29 80 5F 00 Note: Press the PAUSE button of the adjustment remote commander each time to set the data. 5) Select page: 6, address: 01, set data: A7, and press the PAUSE button. 6) Select page: 6, address: 01, set data: A5, and press the PAUSE button. (The auto white balance adjustment is performed and the adjustment data is stored in page: F, address: 3F, 40 and 80.) 7) Select page: 6, address: 02, and check that the data is “01”. 8) Select page: 6, address: 01, set data: 3F, and press the PAUSE button. 9) Select page: 0, address: 03, and set data: 04. 10) Select page: 1, and check that the display data (Note 4) satisfies the R ratio specified value. 11) Select page: 0, address: 03, and set data: 05. 12) Select page: 1, and check that the display data (Note 4) satisfies the B ratio specified value. 13) Select page: F, address: 49 to 4C, and input the data noted down at step 3). Note: Press the PAUSE button of the adjustment remote commander each time to set the data. Processing after Completing Adjustments: 1) Select page: 0, address: 03, and set data: 00. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00 5-19, 12. Color Reproduction Adjustment Adjust the color Separation matrix coefficient so that proper color reproduction is produced. Mode STILL Subject Color bar chart (Color reproduction adjustment frame) Adjustment Page F Adjustment Address 41 to 48, 5C to 5F Note 1: This adjustment should be carried out upon completion of “Auto White Balance Standard Data Input” and “Auto White Balance Adjustment”. Note 2: If the data of page: 6, address: 02 is “01”, select page: 6, address: 01, set data: 00, and press the PAUSE button. Note 3: After the power is turned on, this adjustment can be done only once. Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Check that the picture frame is set to the specified position. (Refer to “8. Picture Frame Setting”.) 3) Select page: B, address: 67, after noting down the data, set data: 00, and press the PAUSE button. 4) Select page: 6, address: 01, set data: AB, and press the PAUSE button. Note: Observe the TV monitor and check that a sign “ ” is indicated inside each color zone of the yellow, cyan, red and blue. 5) Select page: 6, address: 12, set data: 80, and wait for 1 seconds. 6) Select page: 6, address: 12, set data: 00, and wait for 2 seconds. 7) Select page: 6, address: 01, set data: A9, and press the PAUSE button. (The color reproduction adjustment is performed and the adjustment data is stored in page: F, address: 41 to 48, 5C to 5F.) Note: Observe the TV monitor and check that a sign “ ” is indicated inside each color zone. 8) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: B, address: 67, set the data noted down at step 3), and press the PAUSE button. 3) Select page: 0, address: 01, and set data: 00 5-20, 13. Color Reproduction Check Mode STILL Subject Color bar chart For NTSC mode (Color reproduction adjustment frame) Measurement Point Video output terminal Measuring Instrument NTSC vectorscope (NTSC mode) PAL vectorscope (PAL mode) Specified Value Each center of all color luminance points should settle within each color reproduction frame. Menu setting: 1) VIDEO OUT of SET UP menu ... NTSC (NTSC mode) ... PAL (PAL mode) Checking method: 1) Select page: 0, address: 01, and set data: 01. Burst position 2) Select page: 5, address: F1, and set data: FF. 3) Check that the picture frame is set to the specified position. (Refer to “8. Picture Frame Setting”.) 4) Select page: B, address: 67, after noting down the data, set data: 00, and press the PAUSE button of the adjustment remote For PAL mode commander. 5) Select page: 6, address: 10, and set data: 01. Burst position 6) Select page: E, address: 52, after noting down the data, set data: 0A, and press the PAUSE button. 7) Select page: 6, address: 01, set data: 0F, and press the PAUSE button. 8) Select page: 6, address: 12, set data: 80, and wait for 1 seconds. 9) Select page: 6, address: 12, set data: 00, and wait for 2 seconds. 10) Adjust the GAIN and PHASE of the vectorscope, and adjust the burst luminance point to the burst position of the color reproduction frame. 11) Check that each center of all color luminance points is settled in each color reproduction frame. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 2) Select page: 6, address: 10, and set data: 00. Fig. 5-1-13. 3) Select page: E, address: 52, set the data noted down at step 6) of “Checking method”, and press the PAUSE button. 4) Select page: B, address: 67, set the data noted down at step 4) of “Checking method”, and press the PAUSE button. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-21, 14. White Balance Check Mode STILL Subject Clear chart (Color reproduction adjustment frame) Measurement Point Display data of Viode output page 1 (Note 2) terminal Measuring Adjustment remote Vectorscope Instrument commander Specified Value R ratio: 3E00 to 4200 Fig. 5-1-14. B ratio: 3E00 to 4200 A to B Note 1: Refer to “8. Picture Frame setting” for XH, XL, YH and YL. Note 2: Displayed data of page 1 of the adjustment remote commander. 1 : XX : XX Display data Checking method: 1) Check that the lens is not covered with any filter. Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 90, and set data: XL. (Note1) 3) Select page: 6, address: 91, and set data: XH. (Note1) 4) Select page: 6, address: 92, and set data: YL. (Note1) 5) Select page: 6, address: 93, and set data: YH. (Note1) 6) Select page: 6, address: 6C, and set data: 01. R-Y 2mm 7) Select page: 6, address: 01, set data: 79, and press the PAUSE button, and wait for 1 second. 8) Select page: 6, address: 2C, and set data: 01. B-Y • INDOOR data check 9) Select page: 6, address: 01, set data: 0F, and press the PAUSE button. 2mm 10) Select page: 0, address: 03, and set data: 04. 11) Select page: 1, and check that the display data (Note2) satisfies Fig. 5-1-14 (A). the R ratio specified value. 12) Select page: 0, address: 03, and set data: 05. 13) Select page: 1, and check that the display data (Note2) satisfies R-Y0.5mm the B ratio specified value. B-Y • INDOOR luminance point check 14) Select page: 0, address: 03, and set data: 00. 2mm 15) Check that the center of the white luminance point is within 3mm the circle shown Fig. 5-1-14. (A). • OUTDOOR luminance point check 3mm 16) Place the C14 filter on the lens. 17) Select page: 0, address: 01, and set data: 01. Fig. 5-1-14 (B). 18) Select page: E, address: 4B, after noting down the data, set data: 20, and press the PAUSE button. 19) Select page: 6, address: 01, set data: 3F, and press the PAUSE button. 20) Check that the center of the white luminance point settles in the circle shown Fig. 5-1-14. (B). Processing after Completing Adjustments: 1) Select page: E, address: 4B, set the data noted down at step 18), and press the PAUSE button. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. 3) Select page: 6, address: 6C, and set data: 00. 4) Select page: 0, address: 01, and set data: 00. 5-22, 15. Strobe White Balance Adjustment 16. Strobe Light Level and White Balance Check Adjust the white balance when the strobe light flashes. Check the light level regulation and the white balance when the Mode STILL strobe light flashes. Subject A plate which reflection rate is 18 % Mode STILL (1.0m from the front of the lens) Subject A plate which reflection rate is 18% Adjustment Page F (1.0 m from the front of the lens) (Note 1) Adjustment Address 4D, 4E, 64, 69, 6A, 6B Measurement Point Display data of page: 1 Note 1: Perform this adjustment in the dark room or use a dark box. Measuring Instrument Adjustment remote commander Note 2: Any light other than the strobe light should not light up the plate. Specified value Y level data: 60 to 94 (Note 4) Note 3: This adjustment should be carried out upon completion of “HALL Adjustment”, “Flange Back Adjustment”, “Light Level R-Y data: FA to FF or 00 to 06 Adjustment” and “Auto White Balance Adjustment”. (Note 5) Note 4: After the power is turned on, this adjustment can be done only B-Y data: FA to FF or 00 to 06 once. (Note 5) Switch setting: Note 1: Perform this adjustment in the dark room or use a dark box. 1) FLASH ... ON Note 2: Any light other than the strobe light should not light up the plate. Note 3: This adjustment should be carried out upon completion of “HALL Adjusting method: Adjustment”, “Flange Back Adjustment”, “Light Level Adjustment”, “Auto White Balance Adjustment” and “Strobe White 1) Select page: 0, address: 01, and set data: 01. Balance Adjustment”. 2) Select page: 6, address: 90, and set data: 00. Note 4: Display data of pag: F, address: 64 of the adjustment remote 3) Select page: 6, address: 91, and set data: 00. commander. 4) Select page: 6, address: 92, and set data: 00. F : XX : 64 5) Select page: 6, address: 93, and set data: A0. Y level data 6) Select page: 6, address: 6C, and set data: 01. 7) Select page: 6, address: 2C, and set data: 01. Note 5: Display data of page 1 of the adjustment remote commander. 8) Select page: 6, address: 01, set data: 79, and press the PAUSE 1 : XX : XX B-Y data button. R-Y data 9) Select page: 6, address: 01, set data: 67, and press the PAUSE button. (Check the flashing of the strobe light.) Switch setting: 10) Select page: 6, address: 02, and check that the data is “01”. 1) FLASH ... ON (Note 5) 11) Select page: 6, address: 01, set data: 00, and press the PAUSE Checking method: button. 1) Select page: 0, address: 01, and set data: 01. 12) Select page: 6, address: 01, set data: 79, and press the PAUSE 2) Select page: 6, address: 90, and set data: 00. button. 3) Select page: 6, address: 91, and set data: 00. 13) Select page: 6, address: 01, set data: 67, and press the PAUSE 4) Select page: 6, address: 92, and set data: 00. button. (Check the flashing of the strobe light.) 5) Select page: 6, address: 93, and set data: A0. 14) Select page: 6, address: 02, and check that the data is “01”. 6) Select page: 6, address: 6C, and set data: 01. (Note 5) 7) Select page: 6, address: 2C, and set data: 01. 15) Select page: 6, address: 01, set data: 00, and press the PAUSE 8) Select page: 6, address: 01, set data: 79, and press the PAUSE button. button. 16) Select page: 6, address: 01, set data: 79, and press the PAUSE 9) Select page: 6, address: 01, set data: 67, and press the PAUSE button. button. 17) Select page: 6, address: 01, set data: B9, and press the PAUSE 10) Check the flashing of the strobe light. button. 11) Select page: 6, address: 02, and check that the data is “01”. 18) Check the flashing of the strobe light. 12) Select page: F, address: 64, and check that the Y level data 19) Select page: 6, address: 02, and check that the data is “01”. satisfies the specified value. (Note4) (Note 5) 13) Select page: 0, address: 03, and set data: 02. Note 5: The strobe white balance adjustment is performed and the 14) Select page: 1, and check that the R-Y data and B-Y data satisfy adjustment data is stored in page: F, address: 4D, 4E, 64, 69, 6A and 6B. the specified value respectively.(Note5) Processing after Completing Adjustments: Processing after Completing Adjustments: 1) Select page: 6, address: 2C, and set data: 00. 1) Select page: 0, address: 03, and set data: 00. 2) Select page: 6, address: 93, and set data: 00. 2) Select page: 6, address: 2C, and set data: 00. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE 3) Select page: 6, address: 93, and set data: 00. button. 4) Select page: 6, address: 01, set data: 00, and press the PAUSE 4) Select page: 6, address: 6C, and set data: 00. button. 5) Select page: 0, address: 01, and set data: 00. 5) Select page: 6, address: 6C, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-23, 17. CCD Black Defect Compensation 18. CCD White Defect Compensation Mode STILL Mode STILL Subject Clear chart Subject Clear chart (25 cm from the front of the lens) (25 cm from the front of the lens) (Note 1) (Note 1) Adjustment Page 7 Adjustment Page 7 Adjustment Address 60 to 87 Adjustment Address 88 to A3 Note 1: Check that there are no dust, no dirt and no reflection on the clear Note 1: Check that there are no dust, no dirt and no reflection on the clear chart. chart. Note 2: Any subject other than the clear chart should not be in the screen. Note 2: Any subject other than the clear chart should not be in the screen. Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: F, address: DF, after noting down the data, set 2) Select page: F, address: DE, after noting down the data, set data: 4C, and press the PAUSE button. data: 1E, and press the PAUSE button. 3) Select page: 6, address: 2C, and set data: 01. 3) Select page: F, address: E3, after noting down the data, set data: 4) Select page: 6, address: 90, and set data: 00. 08, and press the PAUSE button. 5) Select page: 6, address: 91, and set data: 03. 4) Select page: 6, address: 01, set data: 8B, and press the PAUSE 6) Select page: 6, address: 92, and set data: 00. button. 7) Select page: 6, address: 93, and set data: 00. (The CCD white defect compensation is performed and the 8) Select page: 6, address: 6C, and set data: 01. adjustment data is stored in page: 7, address: 88 to A3.) 9) Select page: 6, address: 01, set data: 79, and press the PAUSE 5) Select page: 6, address: 02, and check that the data changes to button. “01”. 10) Select page: 6, address: 30, set data: 01, and press the PAUSE 6) Select page: 6, address: 55, and check the data. button and wait for 4 seconds. 00 to 7F : Normal 11) Select page: 6, address: 01, set data: 8D, and press the PAUSE 80 to FF : Defective button. 7) Select page: 6, address: 01, set data: 00, and press the PAUSE (The CCD black defect compensation is performed and the button. adjustment data is stored in page: 7, address: 60 to 87.) 8) Select page: F, address: DE, set data: 0F, and press the PAUSE 12) Select page: 6, address: 02, and check that the data changes to button. “01”. 9) Select page: F, address: E3, set data: A0, and press the PAUSE 13) Select page: 6, address: 55, and check the data. button. 00 to 0A : Normal 10) Select page: 6, address: 01, set data: 87, and press the PAUSE 0B to FF : Defective button. (White defect check) 14) Select page: 6, address: 01, set data: 00, and press the PAUSE 11) Select page: 6, address: 02, and check that the data changes to button. “01”. 15) Select page: F, address: DF, set data: 5A, and press the PAUSE 12) Select page: 6, address: 55, and check the data. button. 00 : Normal 16) Select page: 6, address: 01, set data: 89, and press the PAUSE 01 to FF : Defective button. (Black defect check) 17) Select page: 6, address: 02, and check that the data changes to Processing after Completing Adjustments: “01”. 1) Select page: F, address: DE, set the data noted down at step 2), 18) Select page: 6, address: 55, and check the data. and press the PAUSE button. 00 : Normal 2) Select page: F, address: E3, set the data noted down at step 3), 01 to FF : Defective and press the PAUSE button. 3) Select page: 6, address: 01, and set data: 00, and press the Processing after Completing Adjustments: PAUSE button. 1) Select page: F, address: DF, set the data noted down at step 2), 4) Select page: 0, address: 01, and set data: 00. and press the PAUSE button. 2) Select page: 6, address: 01, and set data: 00, and press the PAUSE button. 3) Select page: 6, address: 2C, and set data: 00. 4) Select page: 6, address: 30, and set data: 00. 5) Select page: 6, address: 91, and set data: 00. 6) Select page: 6, address: 6C, and set data: 00. 7) Select page: 0, address: 01, and set data: 00. 5-24, 1-5. LCD SYSTEM ADJUSTMENT 1. LCD Initial Data Input Before perform the LCD system adjustments, check that the specified Mode PLAY values of “VIDEO SYSTEM ADJUSTMENT” are satisfied. Signal Arbitrary Note 1: The back light (fluorescent tube) is driven by a high voltage AC power supply. Therefore, do not touch the back light holder to Adjustment Page D avoid electrical shock. Adjustment Address 1C, 1D, D0 to D8, DD to DF Note 2: When replacing the LCD unit, be careful to prevent damages caused by static electricity. Adjusting method: Note 3: Set the LCD BRIGHT to the center. 1) Select page: 0, address: 01, and set data: 01. [Adjusting connector] 2) Select page: D, and input the data in the following table. Note: Press the PAUSE button of the adjustment remote commander Most of the measuring points for adjusting the LCD system are each time to set the data. concentrated in CN704 of the SY-59 board. 3) Select page: 0, address: 01, and set data: 00. Connect the Measuring Instruments via the CPC-9 jig (J-6082-393- C, Note4). To operate the adjustment remote commander, connect Address Data Remark the power supply terminal of CPC-9 jig to the DC power supply 1C 00 Fixed data (6.0 to 7.2Vdc). 1D 2C Fixed data The following table shows the Pin No. and signal name of CN704. D0 BC Bright adj. Note 4: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. D1 80 Color adj. Pin No. Signal Name Pin No. Signal Name D2 B9 White balance adj. 1 N.C 10 UNREG D3 B7 White balance adj. 2 N.C 11 LANC IN D4 BE Contrast adj. 3 N.C 12 LANC OUT D5 C8 D range adj. 4 REG GND 13 N.C D6 7C V-COM level adj. 5 X CPC IN 14 RF7 D7 80 VCO adj. (NTSC) 6 N.C 15 TXD D8 74 V-COM adj. 7 HSY 16 RXD DD 88 VCO adj. (PAL) 8 PANEL COM 17 RESET DE 13 Fixed data 9 VG 18 VDD DF 11 Fixed data Table 5-1-7. SY-59 board CN704 18 Conductor side 18 pin flexible board (Note) P Note: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. (Fig 1) Remove the check cover by rotating the metal bar in the direction of the arrow of ø1.6 or less centering around the point “P”. Note: Do not reuse the check cover that is once removed. Fig.5-1-15. 5-25, 2. VCO Adjustment (SY-59 board) 3. D Range Adjustment (SY-59 board) Set the VCO free-run frequency. If deviated, the LCD screen will Set the D range of the LCD driver to the specified value. If deviated, be blurred. the LCD screen will become blackish or saturated (whitish). Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 7 of CN704 (HSY) Measurement Point Pin 9 of CN704 (VG) Measuring Instrument Frequency counter External trigger: Pin 8 of CN704 (PANEL COM) Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D7 (NTSC) DD (PAL) Adjustment Page D Specified Value f = 15734 ± 30 Hz (NTSC) Adjustment Address D5 f = 15745 ± 30 Hz (PAL) Specified Value A = 3.62 ± 0.05V Menu setting: Adjusting method: VIDEO OUT of SET UP menu ... NTSC 1) Select page: 0, address: 01, and set data: 01. (This adjustment must be performed in NTSC mode, so don’t set 2) Select page: 5, address: F1, set data: 03. the menu setting to “PAL”.) 3) Select page: D, address: D5, change the data and set the voltage (A) between the reversed waveform pedestal and non-reversed Adjusting method: waveform pedestal to the specified value. 1) Select page: 0, address: 01, and set data: 01. 4) Press the PAUSE button of the adjustment remote commander. 2) Select page: 5, address: F0, set data: 01. 5) Select page: 5, address: F1, set data: 00. 3) Select page: D, address: D7, change the data and set the HSY 6) Select page: 0, address: 01, and set data: 00. frequency (f) to the NTSC specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: D, address: DD, change the data and set the HSY frequency (f) to the PAL specified value. 6) Press the PAUSE button. Pedestal 7) Select page: 5, address: F0, set data: 00. 8) Select page: 0, address: 01, and set data: 00.

A

2H Pedestal Fig. 5-1-16. 5-26, 4. Bright Adjustment (SY-59 board) 5. Contrast Adjustment (SY-59 board) Set the level of the VIDEO signal for driving the LCD to the specified Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated value. If deviated, the screen image will be blackish or saturated (whitish). (whitish). Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 9 of CN704 (VG) Measurement Point Pin 9 of CN704 (VG) External trigger: Pin 8 of CN704 External trigger: Pin 8 of CN704 (PANEL COM) (PANEL COM) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Adjustment Page D Adjustment Page D Adjustment Address D0 Adjustment Address D4 Specified Value A = 2.00 ± 0.08V Specified Value A = 3.31 ± 0.05V Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, set data: 03. 2) Select page: 5, address: F1, set data: 03. 3) Select page: 2, address: 10, set data: 01. 3) Select page: D, address: D4, change the data and set the voltage 4) Select page: D, address: D0, change the data and set the voltage (A) between the pedestal and 10 steps peak to the specified (A) between the pedestal and GAMMA1 limiter level to the value. specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F1, set data: 00. 6) Select page: 2, address: 10, set data: 00. 6) Select page: 0, address: 01, and set data: 00. 7) Select page: 5, address: F1, set data: 00. 8) Select page: 0, address: 01, and set data: 00. GAMMA 1 limiter level 10 steps peak

A A

2H 2H Pedestal Pedestal Fig. 5-1-17. Fig. 5-1-18. 5-27, 6. Color Adjustment (SY-59 board) 7. V-COM Level Adjustment (SY-59 board) Set the color saturation to the standard value. If deviated, the color Set the common electrode drive signal level of LCD to the specified will be too dark or light. value. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 9 of CN704 (VG) Measurement Point Pin 8 of CN704 (PANEL COM) External trigger: Pin 8 of CN704 Measuring Instrument Oscilloscope (PANEL COM) Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D6 Adjustment Page D Specified Value A = 6.30 ± 0.05V Adjustment Address D1 Specified Value A = 544 ± 50mV Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: D, address: D6, change the data and set the V- 1) Select page: 0, address: 01, and set data: 01. COM signal level (A) to the specified value. 2) Select page: 5, address: F1, set data: 04. 3) Press the PAUSE button of the adjustment remote commander. 3) Select page: D, address: D1, change the data and set the voltage 4) Select page: 0, address: 01, and set data: 00. (A) between the white 100% (Reference level) and green to the specified value. 4) Press the PAUSE button of the adjustment remote commander. 5) Select page: 5, address: F1, set data: 00. 6) Select page: 0, address: 01, and set data: 00.

A

White 100 %

A

Green 2H Fig. 5-1-20. 2H Fig. 5-1-19. 5-28, 8. V-COM Adjustment (SY-59 board) 9. White Balance Adjustment (SY-59 board) Set the DC bias of the common electrode drive signal of LCD to the Correct the white balance. specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will move, producing flicker and Mode PLAY conspicuous vertical lines. Signal Arbitrary Mode PLAY Measurement Point Signal Arbitrary Check on LCD display Measuring Instrument Measurement Point Check on LCD display Adjustment Page D Measuring Instrument Adjustment Address D2, D3 Adjustment Page D Specified Value The LCD screen should not be Adjustment Address D8 colored. Specified Value The brightness difference between the section A and section B is minimum. Note 1: Use the AC power adaptor during this adjustment. Note 2: Check the white balance only when replacing the following parts. Note: Perform “Bright Adjustment” and “Contrast Adjustment” before this If necessary, adjust them. adjustment. 1. LCD panel 2. Light induction plate Adjusting method: 3. IC803 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, set data: 02. Adjusting method: 3) Select page: 2, address: 10, set data: 02. 1) Select page: 0, address: 01, and set data: 01. 4) Select page: D, address: D8, change the data so that the 2) Select page: 5, address: F1, set data: 02. brightness of the section A and that of the section B is equal. 3) Select page: D, address: D2 and D3, set the data to the initial 5) Press the PAUSE button of the adjustment remote commander. value. Note: Press the PAUSE button of the adjustment remote commander 6) Select page: 5, address: F1, set data: 00. each time to set the data. 7) Select page: 2, address: 10, set data: 00. 8) Select page: 0, address: 01, and set data: 00. Address D2 D3BAData B9 B7 4) Check that the LCD screen is not colored. If colored, changeABthe data of page: D, address: D2 and D3 so that the LCD screen is not colored. Note: To write in the non-volatile memory (EEPROM), press theBAPAUSE button of the adjustment remote commander each time to set the data. 5) Select page: 5, address: F1, set data: 00. A B 6) Select page: 0, address: 01, and set data: 00. Fig. 5-1-21. 5-29, 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENT 1. Battery End Adjustment (SY-59 board) Adjusting method: Check the battery end voltage. 1) Adjust the output voltage of the regulated power supply so that Mode STILL the digital voltmeter display is 3.5 ± 0.1Vdc. 2) Turn off the power supply. Subject All black (Cover the lens with a black 3) Turn on the HOLD switch of the adjustment remote cap) commander. Measurement Point Display data of page: 2, address: 52 4) Turn on the power supply. Measuring Instrument Adjustment remote commander 5) Insert a memory stick to the memory stick slot. Adjustment Page D 6) Select page: 0, address: 01, and set data: 01. 7) Decrease the output voltage of the regulated power supply so Adjustment Address 90 to 94 that the digital voltmeter display is 3.00 ± 0.01Vdc. 8) Select page: 2, address: 52, read the data, and this data is named Switch setting: Dref. FOCUS ... MANUAL 9) Select page: D, address: 90, set data: Dref, and press the PAUSE button of the adjustment remote commander. Connection: 10) Convert Dref to decimal notation, and obtain Dref’. (Refer to 1) Connect the regulated power supply and the digital voltmeter Table 5-2-1. “Hexadecimal-decimal conversion table” of “5-2. to the battery terminal as shown in Fig. 5-1-22. Service mode”) 11) Calculate D91', D92', D93', and D94 using following equations (decimal calculation), convert it to a hexadecimal number, and input each adjustment address. Address: 91 D91' = Dref’+8 Address: 92 D92' = Dref’+10 Address: 93 D93' = Dref’+10 Address: 94 D94' = Dref’+10 Note: After setting each data, be sure to press the PAUSE button. 12) Select page: 0, address: 01, and set data: 00. Regulated power supply Digital voltmeter Fig. 5-1-22. 5-30, 5-2. SERVICE MODE 2-1. ADJUSTMENT REMOTE COMMANDER The adjustment remote commander is used for changing the calculation coefficient in signal processing, EVR data, etc. The adjustment remote commander performs bi-directional communication with the unit using the remote commander signal line (LANC). The resultant data of this bi-directional communication is written in the non-volatile memory. 1. Using the Adjustment Remote Commander 2. Precautions Upon Using the Adjustment Remote 1) Connect the adjustment remote commander to the following Commander connector. Mishandling of the adjustment remote commander may erase the • CN704 of SY-59 board via CPC-9 jig (J-6082-393-C) correct adjustment data at times. To prevent this, it is recommended 2) Set the HOLD switch of the adjustment remote commander to that all adjustment data be noted down before beginning adjustments “HOLD” (SERVICE position). If it has been properly and new adjustment data after each adjustment. connected, the LCD on the adjustment remote commander will display as shown in Fig. 5-2-1. Page Data Address Fig. 5-2-1. 3) Operate the adjustment remote commander as follows. • Changing the page The page increases when the EDIT SEARCH+ button is pressed, and decreases when the EDIT SEARCH– button is pressed. There are altogether 16 pages, from 0 to F. Hexadecimal notation0123456789ABCDEFLCD Display0123456789AbcdEFDecimal notation conversion value0123456789101112131415 • Changing the address The address increases when the FF (M) button is pressed, and decreases when the REW (m) button is pressed. There are altogether 256 addresses, from 00 to FF. • Changing the data (Data setting) The data increases when the PLAY (N) button is pressed, and decreases when the STOP (x) button is pressed. There are altogether 256 data, from 00 to FF. • Writing the adjustment data The PAUSE button must be pressed to write the adjustment data (B, D, E, F, 7 page) in the nonvolatile memory. (The new adjusting data will not be recorded in the nonvolatile memory if this step is not performed.) 4) After completing all adjustments, turn off the main power supply once. 5-31, 2-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Indicates the hexadecimal-decimal conversion table. Hexadecimal-decimal Conversion Table 2 Lower digit of hexadecimal0123456789ABCDEFUpper digit (A) (b) (c) (d) (E) (F) of hexadecimal0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 77 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 1751B(b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note: The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander. (Example) If the DDS display or the adjustment remote commander shows BD (bd); Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number. Table. 5-2-1. 5-32, 2-3. SERVICE MODE 1. Setting the Test Mode 3. Emergency Memory Address of Flash Unit Page D Address 10 Page D Address 67 Data Function Data Function 00 Normal 00 No error 01 Forced STILL mode power ON 04 Flash unit emergency 02 Forced PLAY mode power ON 03 Forced MOVIE mode power ON Using method: 1) When emergency occurs in the flash unit, the data • Before setting the data, select page: 0, address: 01, and set data: corresponding to the error is written in the address 01. Note: When replacing the flash unit, initialize this data. • For page D, the data set is recorded in the non-volatile memory by pressing the PAUSE button of the adjustment remote Initializing method: commander. In this case, take note that the test mode will not be 1) Select page: 0, address: 01, and set data: 01. exited even when the main power is turned off. 2) Select page: D, address: 67, set data: 00, and press the PAUSE • After completing adjustments/repairs, be sure to return the data button of the adjustment remote commander. of this address to “00”, and press the PAUSE button of the 3) Select page: 0, address: 01, and set data: 00. adjustment remote commander. Select page: 0, address: 01, and set data: 00. 2. Bit Value Discrimination Bit values must be discriminated using the display data of the adjustment remote commander for following items. Use the table below to discriminate if the bit value is “1” or “0”. Display on the adjustment remote commander Address Page bit3 to bit0 discrimination bit7 to bit4 discrimination Display on the Bit values adjustment bit3 bit2 bit1 bit0 remote or or or or commander bit7 bit6 bit5 bit40000010001200103001140100501016011070111A8100091001A(A) 1010B(b) 1011C(c) 1100D(d) 1101BE(E) 1110F(F) 1111Example: If “8E” is displayed on the adjustment remote commander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. 5-33, 4. Record of Use check Page D Address 6C to 6F Address Function Remarks 6C Recording counter Counter data 1 6D (Hexadecimal) Counter data 2 6E Counter data 3 6F Recording counter (Hexadecimal) / Counter data 4 MC CAM emergency Note: When this data is “80” to “FF”, the MC CAM (SY-59 board IC501) is abnormal. Using method: 1) The recording counter data is displayed at page: D, addresses: 6C to 6F. These data are named D6C, D6D, D6E and D6F respectively. 2) Convert D6C, D6D, D6E and D6F to decimal notation, and obtain D6C’, D6D’, D6E’ and D6F’. (Refer to Table 5-2-1. “Hexadecimal-decimal conversion table”) 3) Calculate the recording counter (N) using following equation. (Decimal calculation) N = D6C’ + D6D’ × 256 + D6E’ × 65536 + D6F’ × 16777216 Initializing method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 6C to 6F, and write data: 00 to each address. Note: Press the PAUSE button of the adjustment remote commander each time to set the data. 3) Select page: 0, address: 01, and set data: 00. 5. Self Diagnostics Log check Page 2 Address 90 to A2 Example: C : 32 : 01 Address Function Address : 92, 95, 98, 9B, 9E, A1 90 1st error occurrence code Address : 91, 94, 97, 9A, 9D, A0 91 Address : 90, 93, 96, 99, 9C, 9F (Note) 93 2nd error occurrence code Note: “C” → “01” “E” → “03” 96 3rd error occurrence code 99 4th error occurrence code 9A 9B 9C 5th error occurrence code 9D 9E 9F 6th error occurrence code A0 A1 A2 Numbers of error occurrence (0 to 6) Using method: 1) The self diagnostics log is displayed at page: 2, addresses: 90 to A2. Note: This data will be erased when the battery or DC power supply is removed. 5-34, 6. Switch check (1) Page 2 Address 43 Bit Function When bit value = 1 When bit value = 0 0 XPOWER SW OFF ON (MS block S101) 1 XCAM/PLAY SW PLAY STILL or MOVIE (MS block S102) 2 SHUTTR SW OFF ON (MS block S107) 3 XSHUTTER LOCK SW OFF ON (MS block S103) 4 MS IN IN OUT (Memory stick) 7 XSTILL/MOVIE SW MOVIE STILL or PLAY (MS block S102) Using method: 1) Select page: 2, address: 43. 2) By discriminating the bit value of display data, the state of the switches can be discriminated. 7. Switch check (2) Page 2 Address 54 to 56 Using method: 1) Select page: 2, address: 54 to 56. 2) By discriminating the display data, the pressed key can be discriminated. Data Address 00 to 14 15 to 3B 3C to 64 65 to 91 92 to BD BE to E9 EA to FF 54 ZOOM T ZOOM W LENS REVERSE LENS NORMAL (KEY AD0) (MS block) (MS block) (MS block) (MS block) (IC404 uk) (S104) (S105) (S106) (S106) 55 CONTROL CONTROL UP DISPLAY VOLUME + / VOLUME – / (KEY AD1) DOWN (HF block) (HF block) PROGRAM AE + PROGRAM AE – No key input (IC404 ul) (HF block)(S101) (S101) (S103) (HF block)(S105) (HF block)(S107) CONTROL CONTROL CONTROL LCD LCD 56 FLASH PROGRAM AE RIGHT LEFT SET BACKLIGHT BACKLIGHT (KEY AD2) (HF block) (HF block) (HF block) (HF block) (HF block) OFF ON (IC404 i;) (S102) (S107) (S101) (S101) (S101) (HF block)(S106) (HF block)(S106) 8. LED check Page 2 Address 06 Bit1 Using method: 1) Select page: 2, address: 06, and set the bit value of Bit1 to “1”. 2) Check that all LED except for the ACCESS LED are lit. 3) Select page: 2, address: 06, and set the bit value of Bit1 to “0”. 5-35, 9. Position sensor check (SY-59 board SE401) Page 2 Address 42 Bit0, Bit1 Using method: 1) Install the camera in the normal condition. 2) Select page: 2, address: 42, and check the bit value of Bit0 is “1” and that of Bit1 is”1". 3) Install the camera so that the AV jack side is faced toward the bottom. 4) Select page: 2, address: 42, and check the bit value of Bit0 is “0” and that of Bit1 is”1". 5) Install the camera so that the PLAY/STILL/MOVIE switch side is faced toward the bottom. 6) Select page: 2, address: 42, and check the bit value of Bit0 is “1” and that of Bit1 is”0". 5-36E,

DSC-F55V SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number have some differences from the original one. in the exploded views are not supplied. The components identified by mark 0 or dotted line with mark 0 are critical for safety. • Items marked “*” are not stocked since they Replace only with part number specified. are seldom required for routine service. Some delay should be anticipated when ordering these items. 6-1-1. OVERALL SECTION Camera block section (See page 6-3) 8 Cabinet (rear) section (See page 6-4)

G

not supplied5GDBCEAFEC3

F

D 1D-14 D3 B SY A- 1 59 not supplied11611Cabinet (front) section (See page 6-2) 71 : BT001(Lithium battary) SY-59 board on the mount position. (See page 4-35) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 1 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 5 1-673-451-21 FP-109 FLEXIBLE BOARD 2 A-7074-497-A DD-143 BOARD, COMPLETE * 6 3-056-033-02 SHEET, FLEXIBLE RETAINER * 3 3-055-002-01 FRAME, DD * 7 3-062-773-01 SHEET, PANEL INSULATING 4 A-7096-319-A SY-59 BOARD, COMPLETE (SERVICE) 8 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING 6-1, 6-1-2. CABINET (FRONT) SECTION BT901 62 55 not supplied not supplied 51 60 not supplied Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 51 X-3950-645-1 CABINET (FRONT) ASSY * 58 X-3949-591-1 ARM ASSY, BATTERY LID 52 3-061-013-01 SCREW, TRIPOD FIXED 59 3-050-594-01 SPRING, COMPRESSION 53 3-056-262-01 SPRING, BRAKE 60 7-624-102-04 STOPRING 1.5, TYPE -E 54 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 61 3-061-014-01 LID, BATTERY * 55 3-054-937-01 SPRING, BT RELEASE 62 3-355-424-21 SCREW, TAPPING * 56 3-054-960-11 COVER, BATTERY 63 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING 57 3-054-938-01 SCREW, STEP BT901 1-694-531-11 TERMINAL BOARD, BATTERY 6-2, 6-1-3. CAMERA BLOCK SECTION

C

108 A MIC901 not 103 supplied 103 104 125 D 105 127110 125 102 D IC102 not supplied 116 CD-2 108 115 64 118CB104 117 126 111BA124 not supplied 106101 121 112 111 Be sure to read “Precautions Upon Replacing CCD Imager” on page 4-7 when changing the CCD imager. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 101 X-3950-643-1 BASE ASSY, LENS 116 3-054-555-11 RUBBER (K), SEAL 102 3-054-954-01 CUSHION, MICROPHONE 117 A-7074-498-A CD-264 BOARD, COMPLETE 103 1-960-646-11 HARNESS (MC-081) 118 3-318-203-11 SCREW (B1.7X6), TAPPING 104 3-054-938-01 SCREW, STEP 119 X-3950-644-1 CABINET (REAR) ASSY, LENS * 105 3-056-170-01 SHEET (D), SOUND ABSORPTION * 120 3-056-169-01 SHEET (C), SOUND ABSORPTION * 106 3-056-034-01 CUSHION, FLEXIBLE 121 3-055-027-01 FLEXIBLE STABILIZER 107 3-054-977-11 RETAINER, MICROPHONE * 122 3-055-916-03 SHEET, SHIELD 108 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING * 123 3-063-124-01 SHEET (KB), SOUND ABSORPTION 0109 1-476-138-11 FLASH UNIT * 124 3-063-066-01 SHEET, FLEXIBLE ELECTROSTATIC 110 1-673-450-11 FP-108 FLEXIBLE BOARD 125 1-959-947-11 HARNESS (DC-67) 111 A-7030-985-A LENS ASSY * 126 3-061-010-01 REINFORCEMENT, CONVERSION LENS 112 1-673-449-11 FP-107 FLEXIBLE BOARD * 127 3-063-125-01 SHEET (LB), SOUND ABSORPTION * 113 3-062-887-01 RING, LENS FLEXIBLE IC102 A-7031-119-A CCD BLOCK ASSY (CCD IMAGER) 114 3-054-554-11 ADAPTOR (K), CCD FITTING MIC901 1-542-428-11 MICROPHONE UNIT 115 1-758-441-11 FILTER BLOCK, OPTICAL Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. 6-3 Replace only with part number specified., 6-1-4. CABINET (REAR) SECTION 157 169 SP901 not C supplied 164 not supplied not supplied 157 167 160

A

ND901 not supplied 155 C 152 LCD901

B

154 B

A

151 163 157 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 151 1-673-452-21 FP-110 FLEXIBLE BOARD * 163 3-055-915-01 CUSHION, HF 152 3-056-030-01 LOCK ACE(M1.7),0 PLATE 2 MAIN 164 3-054-992-01 KNOB, POWER 153 3-061-007-01 COVER, JACK 165 3-055-029-21 COVER, CHECK 0154 1-418-880-11 TRANSFORMER UNIT, INVERTER * 166 3-056-467-01 SHEET (C), ELECTROSTATIC 155 1-959-604-12 HARNESS (DB-51) 167 3-355-424-21 SCREW, TAPPING 156 3-054-948-01 SHEET, BACK LIGHT 168 3-054-990-01 SLEEVE 157 3-056-092-02 SCREW, HEAD (2 LOCK) TAPPING 169 X-3946-488-1 SPRING ASSY, AE LEAF 158 1-418-338-11 SWITCH BLOCK, CONTROL (HF) 170 7-624-102-04 STOP RING 1.5, TYPE -E 159 3-055-028-21 KNOB, FUNCTION LCD901 1-803-549-33 MODULE, CRYSTAL INDICATION 160 3-061-008-01 PIN, JACK COVER 0ND901 1-517-878-11 TUBE, FLUORESCENT, COLD CATHODE 161 1-418-339-11 SWITCH BLOCK, CONTROL (MS) SP901 1-505-862-61 SPEAKER (2.0 CM) 162 X-3950-646-1 CABINET (REAR) ASSY Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. 6-4 Replace only with part number specified.,

CD-264 DD-143

6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS When indicating parts by reference number, parts list may be different from the parts All resistors are in ohms. please include the board name. specified in the diagrams or the components METAL: metal-film resistor used on the set. METAL OXIDE: Metal Oxide-film resistor The components identified by mark 0 or • -XX, -X mean standardized parts, so they may F: nonflammable dotted line with mark 0 are critical for safety. have some difference from the original one. • COILS Replace only with part number specified. • Items marked “*” are not stocked since they uH: µH • Abbreviation are seldom required for routine service. Some • SEMICONDUCTORS AUS : Australian model. delay should be anticipated when ordering these In each case, u: µ, for example: HK : Hong Kong model. items. uA...: µA... , uPA... , µPA... , CN : Chinese model. • CAPACITORS: uPB... , µPB... , uPC... , µPC... , JE : Tourist model. uF: µF uPD..., µPD... J : Japanese model. Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks A-7074-498-A CD-264 BOARD, COMPLETE < RESISTOR > ********************** (Ref.No.:3000 Series) R101 1-218-954-11 RES-CHIP 1.2K 5% 1/16W (IC102 is not included to mounted board) R102 1-218-953-11 RES-CHIP 1K 5% 1/16W R103 1-218-941-11 RES-CHIP 100 5% 1/16W < CAPACITOR > R104 1-218-989-11 RES-CHIP 1M 5% 1/16W R105 1-218-958-11 RES-CHIP 2.7K 5% 1/16W C101 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C102 1-109-982-11 CERAMIC CHIP 1uF 10% 10V R106 1-218-959-11 RES-CHIP 3.3K 5% 1/16W C103 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R107 1-218-990-11 SHORT 0 C104 1-131-862-91 TANTAL. CHIP 47uF 20% 4V R108 1-242-946-81 RES-CHIP 2.7 5% 1/16W C105 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R109 1-242-946-81 RES-CHIP 2.7 5% 1/16W R112 1-218-937-11 RES-CHIP 47 5% 1/16W C106 1-119-751-11 TANTAL. CHIP 22uF 20% 16V ************************************************************** C107 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C109 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V A-7074-497-A DD-143 BOARD, COMPLETE C110 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V ********************** C111 1-107-820-11 CERAMIC CHIP 0.1uF 16V (Ref.No.:2000 Series) C112 1-113-985-11 TANTAL. CHIP 10uF 20% 20V < CAPACITOR > C115 1-164-850-11 CERAMIC CHIP 10PF 0.50PF 16V C116 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C001 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C117 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C002 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V C118 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V C003 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C004 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C119 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C005 1-162-979-11 CERAMIC CHIP 0.0027uF 10% 50V C120 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C006 1-164-874-11 CERAMIC CHIP 100PF 5% 16V < CONNECTOR > C007 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C008 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V CN101 1-785-902-21 CONNECTOR, FFC/FPC (ZIF) 23P C009 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V CN102 1-784-342-21 HOUSING, CONNECTOR 2P C010 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V CN103 1-785-946-21 CONNECTOR 3P C011 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V < IC > C012 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C013 1-164-876-11 CERAMIC CHIP 120PF 5% 16V IC101 8-759-339-63 IC NJM2118V-TE2 C014 1-164-874-11 CERAMIC CHIP 100PF 5% 16V IC102 A-7031-119-A CCD BLOCK ASSY (CCD IMAGER) C015 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V < COIL > C016 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C017 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V L101 1-469-058-11 INDUCTOR CHIP 22uH C018 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L102 1-414-757-11 INDUCTOR 100uH C019 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C022 1-164-939-11 CERAMIC CHIP 0.0022uF 10% 16V < TRANSISTOR > C023 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V Q101 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C024 1-164-940-11 CERAMIC CHIP 0.0033uF 10% 16V Q102 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1 C025 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C026 1-109-982-11 CERAMIC CHIP 1uF 10% 10V C027 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C028 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V C029 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C030 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C031 1-113-682-11 TANTAL. CHIP 33uF 20% 10V Be sure to read “Precautions Upon Replacing CCD Imager” C032 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V on page 4-7 when changing the CCD imager. 6-5,

DD-143

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C033 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L006 1-414-751-11 INDUCTOR 1uH C034 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L007 1-414-751-11 INDUCTOR 1uH C035 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L008 1-414-392-21 INDUCTOR 1uH C036 1-109-994-11 CERAMIC CHIP 2.2uF 10% 10V L009 1-414-753-91 INDUCTOR 4.7uH C037 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V L010 1-414-756-11 INDUCTOR 47uH C038 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V L011 1-414-392-21 INDUCTOR 1uH C039 1-107-682-11 CERAMIC CHIP 1uF 10% 16V L012 1-414-757-11 INDUCTOR 100uH C040 1-109-982-11 CERAMIC CHIP 1uF 10% 10V L013 1-414-757-11 INDUCTOR 100uH C041 1-107-682-11 CERAMIC CHIP 1uF 10% 16V L014 1-414-392-21 INDUCTOR 1uH C042 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L015 1-414-756-11 INDUCTOR 47uH C043 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V L016 1-414-757-11 INDUCTOR 100uH C044 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V C045 1-107-682-11 CERAMIC CHIP 1uF 10% 16V < TRANSISTOR > C048 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C049 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V Q002 8-729-427-16 TRANSISTOR XP4113-TXE Q003 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO C050 1-107-682-11 CERAMIC CHIP 1uF 10% 16V Q004 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO C051 1-109-982-11 CERAMIC CHIP 1uF 10% 10V Q005 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO C052 1-127-760-91 CERAMIC CHIP 4.7uF 10% 6.3V Q006 8-729-162-13 TRANSISTOR 2SC1621-T1B2B3 C053 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C054 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V Q007 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO Q008 8-729-162-13 TRANSISTOR 2SC1621-T1B2B3 C056 1-109-982-11 CERAMIC CHIP 1uF 10% 10V Q009 8-729-043-94 TRANSISTOR CPH3106-PM-TL C057 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V Q010 8-729-043-94 TRANSISTOR CPH3106-PM-TL C058 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V Q011 8-729-049-11 TRANSISTOR CPH3206-TL C059 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C060 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V Q012 8-729-047-74 TRANSISTOR CPH5701-TL Q013 8-729-047-74 TRANSISTOR CPH5701-TL C061 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3V Q014 8-729-047-68 TRANSISTOR 2SK1830-TE85L Q015 8-729-048-19 TRANSISTOR CPH5704-TL < CONNECTOR > Q016 8-729-046-00 TRANSISTOR CPH6301-TL CN001 1-774-730-21 PIN, CONNECTOR (PC BOARD) 3P Q017 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO CN002 1-785-946-21 CONNECTOR 3P Q019 8-729-044-84 TRANSISTOR CPH3403-TL CN003 1-785-900-21 CONNECTOR 5P Q020 8-729-044-84 TRANSISTOR CPH3403-TL CN004 1-785-918-21 CONNECTOR, BOARD TO BOARD 40P Q021 8-729-048-19 TRANSISTOR CPH5704-TL Q022 8-729-048-19 TRANSISTOR CPH5704-TL < DIODE > Q023 8-729-048-18 TRANSISTOR CPH5601-TL D001 8-719-074-08 DIODE MA4ZD03001S0 Q024 8-729-427-46 TRANSISTOR XP4213-TXE D002 8-719-075-12 DIODE MA3XD21001S0 Q025 8-729-037-74 TRANSISTOR UN9213J-(K8).SO D003 8-719-071-34 DIODE RB521S-30-TE61 Q029 8-729-427-46 TRANSISTOR XP4213-TXE D004 8-719-074-08 DIODE MA4ZD03001S0 Q030 8-729-037-71 TRANSISTOR UN9210J-(K8).SO D005 8-719-074-08 DIODE MA4ZD03001S0 Q031 8-729-042-57 TRANSISTOR UN9110J-(K8).SO D006 8-719-074-08 DIODE MA4ZD03001S0 Q032 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO D007 8-719-074-08 DIODE MA4ZD03001S0 Q033 8-729-042-26 TRANSISTOR 2SB1462J-QR(K8).SO D062 8-719-056-61 DIODE MAZS082008SO < RESISTOR > < FUSE > R001 1-208-939-11 METAL CHIP 150K 0.5% 1/16W 0F001 1-576-406-11 FUSE, MICRO (1.4A/32V)(1608) R002 1-208-721-11 METAL CHIP 39K 0.5% 1/16W 0F002 1-576-406-11 FUSE, MICRO (1.4A/32V)(1608) R003 1-218-977-11 RES-CHIP 100K 5% 1/16W 0F003 1-576-406-11 FUSE, MICRO (1.4A/32V)(1608) R004 1-208-711-11 METAL CHIP 15K 0.5% 1/16W 0F004 1-576-406-11 FUSE, MICRO (1.4A/32V)(1608) R005 1-208-711-11 METAL CHIP 15K 0.5% 1/16W < IC > R006 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W R007 1-208-711-11 METAL CHIP 15K 0.5% 1/16W IC001 8-759-581-99 IC MB3827PFV-G-BND-ER R008 1-218-970-11 RES-CHIP 27K 5% 1/16W IC002 8-759-486-48 IC XC6372C351PR R010 1-218-963-11 RES-CHIP 6.8K 5% 1/16W R011 1-218-973-11 RES-CHIP 47K 5% 1/16W < COIL > R012 1-208-719-11 METAL CHIP 33K 0.5% 1/16W L001 1-416-510-21 INDUCTOR 100uH R013 1-208-715-11 METAL CHIP 22K 0.5% 1/16W L002 1-416-344-11 INDUCTOR 10uH R014 1-218-970-11 RES-CHIP 27K 5% 1/16W L003 1-416-345-11 INDUCTOR 22uH R015 1-218-973-11 RES-CHIP 47K 5% 1/16W L004 1-416-345-11 INDUCTOR 22uH R016 1-218-973-11 RES-CHIP 47K 5% 1/16W L005 1-416-345-11 INDUCTOR 22uH Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. 6-6 Replace only with part number specified.,

DD-143 SY-59

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R017 1-218-970-11 RES-CHIP 27K 5% 1/16W R081 1-218-981-11 RES-CHIP 220K 5% 1/16W R018 1-218-969-11 RES-CHIP 22K 5% 1/16W R082 1-218-973-11 RES-CHIP 47K 5% 1/16W R020 1-208-927-11 METAL CHIP 47K 0.5% 1/16W R021 1-218-970-11 METAL CHIP 27K 0.5% 1/16W < TRANSFORMER > R022 1-218-968-11 RES-CHIP 18K 5% 1/16W 0T001 1-433-784-21 TRANSFORMER, DC-DC CONVERTER R023 1-218-970-11 RES-CHIP 27K 5% 1/16W 0T002 1-433-786-21 TRANSFORMER, DC-DC CONVERTER R024 1-218-990-11 SHORT 0 0T003 1-433-785-21 TRANSFORMER, DC-DC CONVERTER R025 1-218-969-11 RES-CHIP 22K 5% 1/16W ************************************************************** R027 1-218-969-11 RES-CHIP 22K 5% 1/16W R028 1-218-972-11 RES-CHIP 39K 5% 1/16W A-7096-319-A SY-59 BOARD, COMPLETE (SERVICE) ********************* R029 1-218-970-11 RES-CHIP 27K 5% 1/16W (Ref.No.:1000 Series) R030 1-208-711-11 METAL CHIP 15K 0.5% 1/16W R031 1-218-942-11 RES-CHIP 120 5% 1/16W ************************************************************** R032 1-218-965-11 RES-CHIP 10K 5% 1/16W R033 1-218-968-11 RES-CHIP 18K 5% 1/16W Electrical parts list of the SY-59 board is R034 1-208-701-11 METAL CHIP 5.6K 0.5% 1/16W not shown. R035 1-208-721-11 METAL CHIP 39K 0.5% 1/16W R036 1-208-713-11 METAL CHIP 18K 0.5% 1/16W pages 6-8 to 6-14 are not shown. R037 1-208-931-11 METAL CHIP 68K 0.5% 1/16W R038 1-208-719-11 METAL CHIP 33K 0.5% 1/16W R039 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R040 1-218-953-11 RES-CHIP 1K 5% 1/16W R041 1-218-990-11 SHORT 0 R042 1-208-711-11 METAL CHIP 15K 0.5% 1/16W R043 1-218-970-11 METAL CHIP 27K 0.5% 1/16W R044 1-218-966-11 RES-CHIP 12K 5% 1/16W R045 1-218-970-11 RES-CHIP 27K 5% 1/16W R046 1-218-990-11 SHORT 0 R047 1-208-711-11 METAL CHIP 15K 0.5% 1/16W R049 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R050 1-218-954-11 RES-CHIP 1.2K 5% 1/16W R051 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R052 1-218-970-11 RES-CHIP 27K 5% 1/16W R053 1-218-968-11 RES-CHIP 18K 5% 1/16W R054 1-218-945-11 RES-CHIP 220 5% 1/16W R055 1-218-952-11 RES-CHIP 820 5% 1/16W R056 1-218-951-11 RES-CHIP 680 5% 1/16W R057 1-218-953-11 RES-CHIP 1K 5% 1/16W R058 1-218-962-11 RES-CHIP 5.6K 5% 1/16W R059 1-218-959-11 RES-CHIP 3.3K 5% 1/16W R060 1-218-965-11 RES-CHIP 10K 5% 1/16W R061 1-218-965-11 RES-CHIP 10K 5% 1/16W R062 1-218-945-11 RES-CHIP 220 5% 1/16W R063 1-218-945-11 RES-CHIP 220 5% 1/16W R064 1-218-985-11 RES-CHIP 470K 5% 1/16W R065 1-218-971-11 RES-CHIP 33K 5% 1/16W R066 1-218-971-11 RES-CHIP 33K 5% 1/16W R067 1-218-973-11 RES-CHIP 47K 5% 1/16W R068 1-218-965-11 RES-CHIP 10K 5% 1/16W R069 1-218-965-11 RES-CHIP 10K 5% 1/16W R070 1-218-977-11 RES-CHIP 100K 5% 1/16W R071 1-218-970-11 RES-CHIP 27K 5% 1/16W R072 1-218-968-11 RES-CHIP 18K 5% 1/16W R073 1-218-965-11 RES-CHIP 10K 5% 1/16W R074 1-218-977-11 RES-CHIP 100K 5% 1/16W R076 1-218-990-11 SHORT 0 R077 1-218-977-11 RES-CHIP 100K 5% 1/16W R078 1-218-973-11 RES-CHIP 47K 5% 1/16W R079 1-218-959-11 RES-CHIP 3.3K 5% 1/16W R080 1-216-864-11 METAL CHIP 0 5% 1/16W Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. 6-7 Replace only with part number specified., Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks MISCELLANEOUS ACCESSORIES ************* *********** 5 1-673-451-21 FP-109 FLEXIBLE BOARD 0 1-475-851-12 ADAPTOR, AC (AC-VF10)(J) 103 1-960-646-11 HARNESS (MC-081) 0 1-475-851-33 ADAPTOR, AC (AC-VF10)(E,HK,AUS,CN,JE) 0109 1-476-138-11 FLASH UNIT 1-569-008-21 ADAPTOR, CONVERSION 2P(E) 110 1-673-450-11 FP-108 FLEXIBLE BOARD 1-573-856-11 ADAPTOR, CHANGE 2P (JE) 112 1-673-449-11 FP-107 FLEXIBLE BOARD 0 1-696-819-11 CORD, POWER (AUS) 115 1-758-441-11 FILTER BLOCK, OPTICAL 0 1-769-608-11 CORD, POWER (E,HK) 125 1-959-947-11 HARNESS (DC-67) 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK) 151 1-673-452-21 FP-110 FLEXIBLE BOARD 0 1-782-476-11 CORD, POWER (CN) 0154 1-418-880-11 TRANSFORMER UNIT, INVERTER 1-783-738-31 CORD, CONNECTION (AV 1.5m) 155 1-959-604-12 HARNESS (DB-51) 1-783-739-22 CORD, CONNECTION (DK-115) (1.6m) 158 1-418-338-11 SWITCH BLOCK, CONTROL (HF) 0 1-790-073-11 CORD, POWER 2P (JE,J) 161 1-418-339-11 SWITCH BLOCK, CONTROL (MS) 1-791-785-11 CORD, CONNECTION (USB) BT901 1-694-531-11 TERMINAL BOARD, BATTERY 3-050-664-11 STRAP, HAND IC102 A-7031-119-A CCD BLOCK ASSY (CCD IMAGER) 3-060-716-01 SOFT (2000), BUNDLE LCD901 1-803-549-33 MODULE, CRYSTAL INDICATION 3-062-820-01 MANUAL, INSTRUCTION (JAPANESE)(J) MIC901 1-542-428-11 MICROPHONE UNIT 3-062-820-11 MANUAL, INSTRUCTION (ENGLISH) 0ND901 1-517-878-11 TUBE, FLUORESCENT,COLD CATHODE (E,HK,AUS,CN,JE) SP901 1-505-862-61 SPEAKER (2.0 CM) 3-062-820-21 MANUAL, INSTRUCTION (FRENCH/GERMAN) ************************************************************** (JE) 3-062-820-31 MANUAL, INSTRUCTION Be sure to read “Precautions Upon Replacing CCD Imager” (SPANISH/PORTUGUESE)(E,JE) on page 4-7 when changing the CCD imager. 3-062-820-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE/SIMPLIFIED CHINESE)(E,HK,CN,JE) 3-062-820-51 MANUAL, INSTRUCTION (RUSSIAN/SWEDISH)(JE) 3-062-820-61 MANUAL, INSTRUCTION (KOREAN)(JE) 3-062-820-71 MANUAL, INSTRUCTION (ARABIC)(E) 3-866-482-01 MANUAL, INSTRUCTION (FOR SAFETY)(J) X-3949-706-1 STRAP ASSY, LENS CAP X-3950-955-1 CAP ASSY, LENS Note : The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. 6-15E, 〈FOR CAMERA COLOR REPRODUCTION ADJUSTMENT〉 For NTSC mode DSC-F55V Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. ✂ For PAL mode DSC-F55V — 105 — ✂,

DSC-F55V Sony Corporation

9-929-836-31 Personal VIDEO Products Company 2000F1617-1 Printed in Japan © 2000.6 — 106 — Published by Safety & Service Engineering Dept.]
15

Similar documents

Page Changed contents
DSC-F55/F55E US Model Canadian Model SERVICE MANUAL Tourist ModelKorea Model DSC-F55 1999. 07 E Model DSC-F55/F55E AEP Model UK Model Australian Model Hong Kong Model Chinese Model DSC-F55E SUPPLEMENT-1 File this supplement-1 with the Service Manual. (99-009) Subject: • Addition of Korea model • Suf
AUTION ou are cautioned that any changes or
DSC-F717 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.0 2003. 08 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS
DSC-F77A SERVICE MANUAL LEVEL1EModel Ver 1.1 2005. 06 Hong Kong Model Revision History Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77A COVER SPECIFICATIONS S
Trademarks About the Carl Zeiss lens
DSC-F77/FX77 SERVICE MANUAL LEVEL 1 AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MAN
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL i
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
DSC-H2 SERVICE MANUAL LEVEL 2 US Model UK Model Chinese Model Korea Model Tourist Model
DSC-H2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006. 02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Argentina Model ON BOARD Hong Kong Model Korea Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WI
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1 Ver 1.2 2005. 09 US Model Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model How to use Australian Model Acrobat Reader Chinese Model Japanese Model Korea Model Tourist Model Internal memory ON BOARD Link SPECIFICATIONS BLOCK DIAGRAMS PRIN
SPECIFICATIONS Camera
DSC-H7/H9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2007.04 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: DSC-H7 Black Model Brazilian Model Tourist Model J
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTR
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.1 2005. 04 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.2 2005. 09 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-N2 SERVICE MANUAL SUPPLEMENT-1
DSC-N2 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.02 SUPPLEMENT-1 File this supplement with the service manual. (PV06-161) • Addition of Brazilian Model • Change of Automatic Adjustment Program • Addition of Brazilian Model & : Points added portion. INITIAL LANGUAGE Default Data Check (Service manual pag
DSC-N2 SERVICE MANUAL Canadian Model
DSC-N2 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.1 2007.02 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. (DI06-165) • Addition of
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model UK Model Hong Kong Model Argentine Model Japanese Model Tourist Model Link
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-N2 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Argentine Model Brazilian Model Japanese Model
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory ON BOARD Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Link SPECIFICAT
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.0 2004.04 US Model Canadian Model Revision History E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P100/P120 AEP Model UK Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.2 2004.07 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Correction of exploded view
DSC-P100/P120 LEVEL 2 DSC-P100 SERVICE MANUAL Canadian ModelChinese Model Korea Model Tourist Model Ver 1.2 2004.07 Japanese Model DSC-P100/P120 US Model AEP Model CORRECTION-1 UK ModelE Model Hong Kong Model We will inform you that there are printing errors Australian Model in the service manual pr
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.1 2004.06 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Change of repair parts
DSC-P10/P12 LEVEL 2 US Model SERVICE MANUAL Canadian ModelDSC-P10 AEP Model Ver 1.5 2004. 05 UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model SUPPLEMENT-3 Tourist ModelJapanese Model File this supplement with the service manual. DSC-P10 (PV04-005) • Change of t
Should the fuse in the plug supplied need to be
DSC-P10/P12 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History DSC-P10 AEP Model UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: DSC-P10 DSC-P10 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAM
Should the fuse in the plug supplied need to be
DSC-P10/P12 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2003. 12 Canadian Model Revision History DSC-P10 AEP Model UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: DSC-P10 DSC-P10 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAM