Download: Trademarks About the Carl Zeiss lens

DSC-F77/FX77 SERVICE MANUAL LEVEL 1 AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA DSC-F77/FX77 COVER SPECIFICATIONS System Operating temperature range sync negative Image device 8.98 mm (1/1.8 type) color 0º to +40ºC (32º to +104ºF) Audio: 327 mV (at a 47 kΩ load) CCD Storage temperature range Output impedance 2.2 kΩ ...
Author: Acal1978 Shared: 8/19/19
Downloads: 1470 Views: 3318

Content

DSC-F77/FX77 SERVICE MANUAL LEVEL 1

AEP Model Ver 1.2 2003. 04 UK Model Revision History E Model Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77 Photo: DSC-FX77 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document.

DIGITAL STILL CAMERA

,

DSC-F77/FX77 COVER SPECIFICATIONS

System Operating temperature range sync negative Image device 8.98 mm (1/1.8 type) color 0º to +40ºC (32º to +104ºF) Audio: 327 mV (at a 47 kΩ load) CCD Storage temperature range Output impedance 2.2 kΩ Primary color filter –20º to +60ºC (–4º to +140ºF) USB jack mini-B Total pixels number of camera Dimensions DSC-F77: DC IN connector Approx. 4 130 000 pixels 92.6 × 71 × 27 mm Camera connector Effective pixels number of camera (3 3/4 × 2 7/8 × 1 1/8 inches) Approx. 3 950 000 pixels DSC-FX77: AC-LM5 AC power adaptor Lens f=7.65 mm 98.1 × 71 × 27 mm Power requirements (35 mm camera conversion: 37mm (3 7/8 × 2 7/8 × 1 1/8 inches) AC 100 to 240 V, 50/60 Hz (1 15/32 inches)) (W/H/D, protruding portions not included) Rated output voltage F2.8 Mass DSC-F77: Approx. 180 g (6.3 oz) DC 4.2 V, 1.5 A Exposure control DSC-FX77: Approx. 185 g (6.5 oz) Operating temperature range Automatic, (NP-FC10 battery pack, “Memory Stick” and 0º to +40ºC (32º to +104ºF) Scene selection (four modes) wrist strap included) Storage temperature range White balance Microphone Electret condenser microphone –20º to +60ºC (–4º to +140ºF) Automatic, Daylight, Cloudy, Speaker Dynamic speaker Dimensions 47 × 30 × 80 mm (1 7/8 × 1 3/16 × 3 1/4 inches) Fluorescent, Incandescent (W/H/D, protruding parts not included) File format (DCF compliant) Bluetooth function (DSC-FX77) Mass Approx. 170 g (6.0 oz) Still images: Exif Ver. 2.2, JPEG Communication type (adaptor only) compliant, GIF (for Clip Motion), Bluetooth standards, ver. 1.1 DPOF compatible Maximum transmission speed1) NP-FC10 battery pack Audio with still image: MPEG1 About 723 Kbps Used battery Lithium ion battery compliant (Monaural) Output Bluetooth standards, Power Class 2 Maximum voltage Movies: MPEG1 compliant (Monaural) Communication distance2) DC 4.2 V Recording media About 10 m (3.3 feet) without obstacles Nominal voltage “Memory Stick” Compatible Bluetooth profile3) DC 3.6 V Flash Recommended distance Basic Imaging Profile (Image Push Initiator, Capacity 2.4 Wh (675 mAh) 0.5 to 1.7 m (1 feet 7 3/4 inches to Image Push Responder, 5 feet 7 inches) Remote Camera Responder) Accessories (when ISO sensitivity is set to Auto) Frequency band • NP-FC10 battery pack (1) 2.4 GHz (2.400 to 2.4835 GHz) • AC-LM5 AC power adaptor (1) Input/output connectors 1) Maximum data transmission speed based on Bluetooth • UC-FA USB cradle Multi connector standards, ver. 1.1. • USB cable (1) This speed depends on the distance between the devices, • A/V connecting cable (1) LCD screen obstacles, radio wave conditions, application software, or the • Power cord (mains lead) (1) LCD panel used OS. • Wrist strap (1) 3.8 cm (1.5 type) TFT drive 2) This distance depends on the obstacles between the devices, • “Memory Stick” (16MB) (1) Total number of dots radio wave conditions, application software, or the OS. • CD-ROM (USB driver: SPVD-008) (1) 123 200 (560×220) dots 3) This specification is in accordance with the intended use • Operating Instructions (1) between two Bluetooth devices. DSC-FX77: Power, general This is defined by the Bluetooth standards. • Bluetooth Function Operating Instructions (1) Used battery pack NP-FC10 UC-FA USB cradle Design and specifications are subject to change Power requirements Input/output connectors without notice. 3.6 V A/V OUT (MONO) jack (Monaural) Power consumption (when shooting) Minijack 1.9 W Video: 1 Vp-p, 75 Ω, unbalanced,

SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. SAFETY CHECK-OUT After correcting the original service problem, perform the following

safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered 5. Check the B+ voltage to see it is at the values specified. connections. Check the entire board surface for solder splashes 6. Flexible Circuit Board Repairing and bridges. • Keep the temperature of the soldering iron around 270˚C 2. Check the interboard wiring to ensure that no wires are during repairing. "pinched" or contact high-wattage resistors. • Do not touch the soldering iron on the same conductor of the 3. Look for unauthorized replacement parts, particularly circuit board (within 3 times). transistors, that were installed during a previous repair. Point • Be careful not to apply force on the conductor when soldering them out to the customer and recommend their replacement. or unsoldering. 4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. — 2 —,

DSC-F77/FX77

COVER SELF-DIAGNOSIS FUNCTION [Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom initialization. Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. — Insert a battery pack correctly. Battery pack is not inserted correctly. E:92:ss Battery pack was installed or removed Turn the power off and on again. when using the AC adaptor. — 3 —,

DSC-F77/FX77

COVER 1. MAIN PARTS Note: • Items marked “*” are not stocked since they are seldom required for routine service. The components identified by Some delay should be anticipated when ordering these items. mark 0 or dotted line with mark • The parts numbers of such as a cabinet are also appeared in this section. 0 are critical for safety. Replace only with part number Refer to the parts number mentioned below the name of parts to order. specified. • Abbreviation AUS: Australian model HK : Hong Kong model J : Japanese model CH : Chinese model JE : Tourist model 1. ORNAMENTAL PARTS LCD window 3-078-131-01 Adhesive sheet (LCD) 3-078-111-01 — 4 —,

DSC-F77/FX77 Checking supplied accessories.

Power cord (1) AC adaptor Battery pack Cradle unit 0 1-696-819-21 (F77: AUS) AC-LM5 (1) NP-FC-10 (1) 1-477-487-11 0 1-769-608-11 (F77: AEP, E/ 0 1-477-488-11 (EXCEPT CH) FX77: AEP) 0 1-477-488-12 (CH) 0 1-782-476-11 (F77: CH) 1-783-374-11 (F77: UK, HK/ Other accessories0 FX77: UK) 01-569-007-11 ADAPTOR, CONVERSION (F77: E, JE) 1-790-732-11 (F77: JE) 01-569-008-21 ADAPTOR, CONVERSION 2P (F77: E)0 1-791-637-11 (J) 3-065-665-05 MANUAL, INSTRUCTION (JAPANESE) (J)0 3-078-407-01 MANUAL, INSTRUCTION (JAPANESE) (F77: J) 3-078-407-11 MANUAL, INSTRUCTION (ENGLISH) (F77: AEP, UK, E, HK, AUS, CH, JE) 3-078-407-21 MANUAL, INSTRUCTION (FRENCH,GERMAN) (F77: AEP) 3-078-407-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (F77: AEP, E, JE) Hand strap (1) USB cable (1) 3-078-407-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) 3-076-646-02 1-823-932-11 (F77: AEP) 3-078-407-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (F77: E, HK, CH, JE) 3-078-407-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (F77: AEP) 3-078-407-71 MANUAL, INSTRUCTION (ARABIC) (F77: E) 3-078-408-01 MANUAL, INSTRUCTION 1) (JAPANESE) (F77: J) 3-078-409-01 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) 3-078-409-11 MANUAL, INSTRUCTION (ENGLISH) (FX77: AEP, UK) 3-078-409-21 MANUAL, INSTRUCTION (FRENCH,GERMAN) (FX77: AEP) 3-078-409-31 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (FX77: AEP) 3-078-410-01 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) 3-079-664-01 MANUAL, INSTRUCTION (BT) (JAPANESE) (FX77: J) 3-079-664-11 MANUAL, INSTRUCTION (BT) (ENGLISH) (FX77: AEP, UK) 3-079-664-21 MANUAL, INSTRUCTION (BT) (FRENCH, GERMAN) (FX77: AEP) 3-079-664-31 MANUAL, INSTRUCTION (BT) (ITALIAN, DUTCH) (FX77: AEP) y EMCS Co. 2003D0500-1 ©2003.4 Published by DI Customer Center -929-997-41 Son A/V connecting cable (1) "Memory Stick" (16MB) ( 1-824-111-11 CD-ROM (SPVD-008 USB driver) (1) 3-077-012-02 (J) 3-077-023-02 (EXCEPT J) — 5 —,

DSC-F77/FX77

LEVEL 1 AEP Model

SERVICE MANUAL UK Model

E Model Ver 1.1 2003. 02 Hong Kong Model Australian Model Japanese Model DSC-F77/FX77 Chinese Model Tourist Model DSC-F77

SUPPLEMENT-1

File this supplement with the service manual. (PV02-011) • Addition and change of accessories • Addition of E, Hong Kong, Australian Models (FX77),

DSC-F77/FX77

1. MAIN PARTS The components identified by & : Points added parts. mark 0 or dotted line with mark - : Points changed parts. 0 are critical for safety. ! Replace only with part number : Points deleted parts. specified. 1. ORNAMENTAL PARTS

Checking supplied accessories.

(Service manual page 5) FORMER NEW Power cord (1) Power cord (1) 01-696-819-21 (F77: AUS) 01-696-819-21 (AUS) [ 01-769-608-11 (F77: AEP, E/FX77: AEP) 01-769-608-11 (AEP, E) [ 01-783-374-11 (F77: UK, HK/FX77: UK) 01-783-374-11 (UK, HK) [ AC adaptor AC adaptor AC-LM5 (1) AC-LM5 (1) 01-477-488-11 (EXCEPT CH) 01-477-488-12 (CH) 01-477-488-12 @ $ Other accessories Other accessories 01-569-007-11 ADAPTOR, CONVERSION (F77: E, JE) 01-569-007-11 ADAPTOR, CONVERSION (E, JE) [ 3-078-407-01 MANUAL, INSTRUCTION (JAPANESE) (F77: J) 3-078-407-03 MANUAL, INSTRUCTION (JAPANESE) (F77: J) [ 3-078-407-11 MANUAL, INSTRUCTION (ENGLISH) 3-078-407-12 MANUAL, INSTRUCTION (ENGLISH) (F77: AEP, UK, E, HK, AUS, CH, JE) [ (F77: AEP, UK, E, HK, AUS, CH, JE) 3-078-407-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) 3-078-407-22 MANUAL, INSTRUCTION (FRENCH, GERMAN) (F77: AEP) [ (F77: AEP) 3-078-407-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) 3-078-407-32 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (F77: AEP, E, JE) [ (F77: AEP, E, JE) 3-078-407-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (F77: AEP) 3-078-407-42 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (F77: AEP) [ 3-078-407-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, 3-078-407-52 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (F77: E, HK, CH, JE) [ SIMPLIFIED CHINESE) (F77: E, HK, CH, JE) 3-078-407-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) 3-078-407-62 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (F77: AEP) [ (F77: AEP) 3-078-407-71 MANUAL, INSTRUCTION (ARABIC) (F77: E) 3-078-407-72 MANUAL, INSTRUCTION (ARABIC) (F77: E) [ 3-078-408-01 MANUAL, INSTRUCTION (JAPANESE) (F77: J) 3-078-408-03 MANUAL, INSTRUCTION (JAPANESE) (F77: J) [ 3-078-409-01 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) 3-078-409-02 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) [ 3-078-409-11 MANUAL, INSTRUCTION (ENGLISH) (FX77: AEP, UK) 3-078-409-12 MANUAL, INSTRUCTION (ENGLISH) [ (FX77: AEP, UK, E, HK, AUS) ) 3-078-409-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) 3-078-409-22 MANUAL, INSTRUCTION (FRENCH, GERMAN) (FX77: AEP) [ (FX77: AEP) — 2 —,

DSC-F77/FX77

& : Points added parts. - : Points changed parts. FORMER NEW 3-078-409-31 MANUAL, INSTRUCTION (ITALIAN, DUTCH) 3-078-409-32 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (FX77: AEP) [ (FX77: AEP) 3-078-409-41 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (FX77: E, HK) ) 3-079-664-11 MANUAL, INSTRUCTION (BT) (ENGLISH) 3-079-664-11 MANUAL, INSTRUCTION (BT) (ENGLISH) (FX77: AEP, UK) (FX77: AEP, UK, E, HK, AUS) ) 9-929-997-84 Sony EMCS Co. 2003B0500-1 ©2003.2 — 3 — Published by DI Customer Center,

DSC-F77/FX77

LEVEL 1 LEVEL 2 LEVEL 3 AEP Model

SERVICE MANUAL UK Model

E Model LEVEL1 Ver 1.2 2003. 04 Hong Kong Model LEVEL2 Ver 1.3 2003. 04 Australian Model LEVEL3 Ver 1.3 2003. 04 Japanese Model DSC-F77/FX77 Chinese Model Korea Model Tourist Model DSC-F77

SUPPLEMENT-2

File this supplement with the service manual. (PV02-024) • Addition of Korea Model (F77),

DSC-F77/FX77

& : Points added portion.

Checking supplied accessories.

Power cord (1) AC adaptor Battery pack Cradle unit 0 1-696-819-21 (AUS) AC-LM5 (1) NP-FC-10 (1) 1-477-487-11 0 1-769-608-11 (AEP, E) 0 1-477-488-12 0 1-782-476-11 (CH) 0 1-783-374-11 (UK, HK) 1-790-732-11 (JE) Other accessories0 1-791-637-11 (J) 01-569-007-11 ADAPTOR, CONVERSION (E, JE)0 0 1-776-985-11 (KR) 01-569-008-21 ADAPTOR, CONVERSION 2P (E) 3-065-665-05 MANUAL, INSTRUCTION (JAPANESE) (J) ) 3-078-407-03 MANUAL, INSTRUCTION (JAPANESE) (F77: J) 3-078-407-12 MANUAL, INSTRUCTION (ENGLISH) (F77: AEP, UK, E, HK, AUS, CH, JE) 3-078-407-22 MANUAL, INSTRUCTION (FRENCH, GERMAN) (F77: AEP) 3-078-407-32 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (F77: AEP, E, JE) Hand strap (1) USB cable (1) 3-078-407-42 MANUAL, INSTRUCTION (ITALIAN, DUTCH) 3-076-646-02 1-823-932-11 (F77: AEP) 3-078-407-52 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (F77: E, HK, CH, JE) 3-078-407-62 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (F77: AEP) 3-078-407-72 MANUAL, INSTRUCTION (ARABIC) (F77: E) 3-078-407-81 MANUAL, INSTRUCTION (KOREAN) (F77: KR) A/V connecting cable (1) "Memory Stick" (16MB) (1) 1-824-111-11 3-078-408-03 MANUAL, INSTRUCTION ) (JAPANESE) (F77: J) 3-078-409-02 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) 3-078-409-12 MANUAL, INSTRUCTION (ENGLISH) (FX77: AEP, UK, E, HK, AUS) 3-078-409-22 MANUAL, INSTRUCTION (FRENCH,GERMAN) (FX77: AEP) 3-078-409-32 MANUAL, INSTRUCTION CD-ROM (ITALIAN, DUTCH) (FX77: AEP) (SPVD-008 USB driver) (1) 3-078-409-41 MANUAL, INSTRUCTION (TRADITIONAL 3-077-012-02 (J) CHINESE, SIMPLIFIED CHINESE) 3-077-023-02 (EXCEPT J) (FX77: E, HK) 3-078-410-01 MANUAL, INSTRUCTION (JAPANESE) (FX77: J) 3-079-664-01 MANUAL, INSTRUCTION (BT) (JAPANESE) (FX77: J) 3-079-664-11 MANUAL, INSTRUCTION (BT) (ENGLISH) (FX77: AEP, UK, E, HK, AUS) 3-079-664-21 MANUAL, INSTRUCTION (BT) (FRENCH, GERMAN) (FX77: AEP) 3-079-664-31 MANUAL, INSTRUCTION (BT) (ITALIAN, DUTCH) (FX77: AEP) • Abbreviation AUS: Australian model HK : Hong Kong model J : Japanese model CH : Chinese model JE : Tourist model KR : Korea model 2003D0500-1 9-929-997-86 Sony EMCS Co. ©2003.4 — 2 — Published by DI Customer Center, 3-078-409-11(1) Getting started _

Digital Still Camera Shooting still images _

Viewing still images _

Operating Instructions

Before operating the unit, please read this manual thoroughly, and Deleting still images _ retain it for future reference.

Owner’s Record Before advanced operations _

The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers Advanced still image shooting_ whenever you call upon your Sony dealer regarding this product. Model No. DSC-FX77 Advanced still image viewing_ Serial No. Still image editing _ Enjoying movies_ Enjoying images on your computer _ Troubleshooting _ Additional information _

DSC-FX77 Index

© 2002 Sony Corporation See also the Bluetooth function operating instructions.,

WARNING NoticeIf static electricity or electromagnetism causes

To prevent fire or shock hazard, do data transfer to discontinue midway (fail), not expose the unit to rain or restart the application or disconnect and moisture. connect the USB cable again.

Notice on the supplied AC

power adaptor for the customers in the United

Kingdom

A moulded plug complying with BS 1363 is Hereby, Sony Corporation, declares that this fitted to this equipment for your safety and digital still camera is in compliance with the convenience. essential requirements and other relevant Should the fuse in the plug supplied need to be provisions of the Directive 1999/5/EC. For replaced, a 5 AMP fuse approved by ASTA or details, please access the following URL: BSI to BS 1362, (i.e., marked with or http://www.compliance.sony.de/ mark) must be used. The Bluetooth function is intended to be used If the plug supplied with this equipment has a in the following countries or areas: Austria, detachable fuse cover, be sure to attach the Belgium, Denmark, Finland, France, fuse cover after you change the fuse. Never Germany, Greece, Ireland, Italy, Luxembourg, use the plug without the fuse cover. If you Netherlands, Norway, Portugal, Spain, should lose the fuse cover, please contact your Sweden, Switzerland, United Kingdom. nearest Sony service station.

For the Customers in Europe

This product has been tested and found compliant with the limits sets out in the R&TTE Directive for using connection cables shorter than 3 meters. Attention The electromagnetic fields at the specific frequencies may influence the picture and sound of this digital camera.,

Before using your camera

Trial recording Do not shake or strike the camera Do not get the camera wet Before you record one-time events, you may In addition to malfunctions and inability to When taking pictures outdoors in the rain or want to make a trial recording to make sure record images, this may render the “Memory under similar conditions, be careful not to get that the camera is working correctly. Stick” unusable or image data breakdown, the camera wet. If moisture condensation damage or loss may occur. occurs, see page 103 and follow the No compensation for contents of the instructions on how to remove it before using recording LCD screen, LCD finder (only models the camera. Contents of the recording cannot be with a LCD finder) and lens compensated for if recording or playback is • The LCD screen and the LCD finder are The pictures used in this manual not possible due to a malfunction of your manufactured using extremely high- The photographs used as examples of pictures camera or recording medium, etc. precision technology so over 99.99% of the in this manual are reproduced images, and are pixels are operational for effective use. not actual images shot using this camera. Back up recommendation However, there may be some tiny black To avoid the potential risk of data loss, always points and/or bright points (white, red, blue Do not aim the camera at the sun or copy (back up) data to a disk. or green in color) that constantly appear on other bright light the LCD screen and the LCD finder. These This may cause irrecoverable damage to your Notes on image data compatibility points are normal in the manufacturing eyes. • This camera conforms with the Design rule process and do not affect the recording in for Camera File system universal standard any way. established by the JEITA (Japan Electronics • Be careful when placing the camera near a and Information Technology Industries window or outdoors. Exposing the LCD Association). screen, the finder or the lens to direct • Playback of images recorded with your sunlight for long periods may cause camera on other equipment and playback of malfunctions. images recorded or edited with other • Close the lens portion when not using the equipment on your camera are not camera. guaranteed. Precaution on copyright Television programs, films, video tapes, and other materials may be copyrighted. Unauthorized recording of such materials may be contrary to the provision of the copyright laws., Trademarks About the Carl Zeiss lens • “Memory Stick,” , and “MagicGate This camera is equipped with a Carl Zeiss Memory Stick” are trademarks of Sony lens which is capable of reproducing fine Corporation. images. The lens for this camera uses the • “Memory Stick Duo” and MTF* measurement system for cameras are trademarks of Sony developed jointly by Carl Zeiss, in Corporation. Germany, and Sony Corporation, and offers • “MagicGate” and are the same quality as other Carl Zeiss lenses. trademarks of Sony Corporation. • “InfoLITHIUM” is a trademark of Sony ∗ MTF is an abbreviation of Modulation Corporation. Transfer Function, a numeric value • Microsoft and Windows are registered indicating the amount of light from a trademarks of the U.S. Microsoft specific part of the subject gathered at the Corporation in the United States and other corresponding position in the image. countries. • Macintosh, Mac OS, and QuickTime, are trademarks or registered trademarks of Apple Computer, Inc. • “Pentium” is a trademark or a registered trademark of Intel Corporation. • The BLUETOOTH trademarks are owned by their proprietor and used by Sony Corporation under license. • In addition, system and product names used in this manual are, in general, trademarks or registered trademarks of their respective developers or manufacturers. However, the ™ or ® marks are not used in all cases in this manual.,

Table of contents

Before using your camera ... 4 Inserting the date and time on a still

Advanced still image

Identifying the parts ... 8 image... 30 Camera... 8 Shooting according to scene conditions shooting USB cradle... 10 (scene selection)... 31 Choosing a focus method...45 How to install/remove your camera... 10 Deciding the still image quality... 33 AF lock shooting using Center AF ...46 Image size and quality ... 34 Setting the distance to the subject

Getting started (Focus preset) ...47 Viewing still images Adjusting the exposure (EV adjustment)

Charging the battery pack ... 11 ...47 Using an external power source... 15 Viewing images on the LCD screen of your Spot light-metering ...48 Using your camera abroad ... 15 camera ... 35 Adjusting color tones (White Balance)...49 Turning on/off your camera ... 16 Viewing on the single-image screen .. 35 Adjusting the flash level ...50 How to use the control button... 17 Viewing on the index Shooting multiple frames (Clip Motion) Setting the date and time... 18 (nine- or triple-image) screen... 36 ...51 Viewing images on a TV screen... 37 Shooting in Multi Burst mode

Shooting still images (Multi Burst) ...52 Deleting still images

Inserting and removing a “Memory Stick” Shooting still images for e-mail ... 20 Deleting images ... 39 (E-MAIL) ...53 Setting the still image size ... 21 Deleting on the Index (nine-image) Shooting still images with audio files Basic still image shooting screen ... 40 (VOICE) ...54 – using auto mode... 22 Deleting on the Index (triple-image) Adding special effects (Picture Effect) ...55 Checking the last image shot screen ... 41 Selecting a Folder...55 – Quick Review ... 23 Formatting a “Memory Stick” ... 43 Creating a new folder...56 Using the smart zoom ... 24 Changing the recording folder ...56 Shooting close-ups – Macro ... 25 Before advanced operations Using the self-timer ... 26 Advanced still image viewing Rotating the lens How to setup and operate your camera .. 44 Changing menu settings ... 44 Selecting the folder and playing back – Mirror mode ... 26 Changing items in the SET UP screen images (Folder)...57Selecting a flash mode... 27 ... 44 Enlarging a portion of a still image...58Shooting with the finder ... 29, Enlarging an image Deleting unnecessary portions of Additional information – Playback zoom...58 movies ... 71 Recording an enlarged image The number of images that can be saved/ – Trimming ...59 Enjoying images on your shooting time...95 Playing back successive images computer Menu items ...96 (Slide show)...59 SET UP items ...101 Rotating still images...60 Copying images to your computer Precautions ...103 – For Windows users... 72 The “Memory Stick” ...104

Still image editing Installing the USB driver... 73 The “InfoLITHIUM” battery pack...105

Installing “Image Transfer” ... 73 Specifications ...106 Protecting images (Protect) ...61 Installing “ImageMixer”... 75 The LCD screen ...108 On the single screen ...61 Connecting your camera to your Index...111 On the Index (nine-image) screen...61 computer... 75 On the Index (triple-image) screen ...62 Copying images using “Image Transfer” Changing image size (Resize)...63 ... 77 Choosing images to print Changing “Image Transfer” settings .. 78 (Print (DPOF) mark)...64 Copying images without using On the single screen ...64 “Image Transfer”... 78 On the Index (nine-image) screen...64 Viewing the images on your computer On the Index (triple-image) screen ...65 ... 79 Image file storage destinations and file

Enjoying movies names... 80

Copying images to your computer Shooting movies...66 – For Macintosh users ... 82 Viewing movies on the LCD screen ...67 Deleting movies ...68 Troubleshooting On the single screen ...68 On the Index (nine-image) screen...68 Troubleshooting ... 84 On the Index (triple-image) screen ...69 Warnings and messages... 92 Editing movies ...70 Self-diagnosis display ... 94 Cutting movies ...70,

Identifying the parts

See the pages in parentheses for details of operation.

Camera

2 7 q; 5 qa qs A Lens H Bluetooth lamp (See the K Microphone B Shutter button (22) Bluetooth function operating L Speaker (bottom surface) C POWER lamp (16) instructions) D POWER button (16) • Use a tripod with a screw length of less than Tripod receptacle (bottom I Bluetooth button (See the 5.5 mm (7/32 inch). You will be unable to E surface) Bluetooth function operating firmly secure the camera to tripods having longer screws, and may damage the camera. F Finder window instructions) • Do not touch the microphone while recording. G Flash (27) J Self-timer lamp (26)/ AF illuminator (28, 101), Attaching the wrist strap2839IBattery/“Memory Stick” cover 4 q; J Access lamp (20) qa K RESET button (84) 5 qs L Battery eject lever (13) 6 M Wrist strap hookqd A Finder (29) D LCD screen E Multi connector (bottom surface) Self-timer/recording (12, 15) lamp (red) F DSPL/LCD ON/OFF button (29) AE/AF lock lamp G MENU button (21) /CHG (green) H MODE dial (18) /CHG lamp (orange) : To shoot still images in auto (12, 27) mode P: To shoot still images in B SMART ZOOM buttons (during program mode shooting) (24)/Index buttons SCN: To shoot in the Scene (during playback) (36) Selection mode C Control button SET UP: To set the SET UP items (Menu on) (v/V/b/B/z) (17)/ : To shoot movies/Clip Motion (Menu off) ( / /7/ ) (27/26/23/ images/Multi Burst mode images 25) : To view or edit images,

USB cradle

A Camera connector B USB ON/OFF switch C (USB) jack (76) D DC IN connector (11) E A/V OUT (MONO) jack (37)

How to install/remove your camera How to install • Be sure to turn off the camera before you install

Install the camera as illustrated below. • Make sure the camera is securely installed to the USB cradle.

How to remove

Grasp the camera and the USB cradle as illustrated below and remove the camera with the lens portion closed. the camera to the USB cradle or remove the camera from the USB cradle. When you remove the AC power adaptor from the USB cradle, hold the DC plug itself and the USB cradle as illustrated below and remove the cable. DC plug,

Getting started Charging the battery pack

Getting started AC power adaptor USB cradle OPEN Battery eject lever123DC plug , Open the battery/“Memory , Insert the battery pack, and , Connect the AC-LM5 AC power

Stick” cover. close the cover. adaptor (supplied) to the DC IN

connector of the USB cradle. Slide the cover in the direction of the arrow. Insert the battery pack with the v mark facing toward the battery compartment as Connect the plug with the v mark facing • When charging the battery pack, make illustrated above. Make sure the battery up. sure the camera is not turned on pack is properly inserted, then close the (page 16). cover. • • Do not short the DC plug on the AC power The camera operates only with the adaptor with a piece of metal. This may cause a “InfoLITHIUM” battery NP-FC10 battery pack malfunction. (C type) (supplied). You cannot use any other • While pushing the battery eject lever down battery pack (page 105). using the front edge of the battery pack, you can easily insert the battery pack.,

Charging the battery pack

(continued) AC power adaptor 2 To a wall outlet (wall socket) Power cord 4 (mains lead) , Connect the power cord (mains lead) to the AC power adaptor and to a wall outlet (wall socket). Charging the battery pack only using , Install the camera to the USB cradle. Install the camera as illustrated above. Charging starts, and the /CHG lamp lights. /CHG /CHG lamp When the /CHG lamp goes out, charging is finished. the AC power adaptor AC power adaptor DC plug Multi connector Power cord (mains lead) You can charge the battery pack without the USB cradle, such as during your travels. Connect the DC plug of the AC power adaptor to the camera with v mark facing down as illustrated below., • When charging the battery pack, make Battery remaining indicator Battery life and the number of Getting started sure the camera is not turned on The battery remaining indicator shows the images that can be recorded/(page 16). • When placing the camera, make sure the LCD remaining shooting or viewing time. viewed screen is facing up. The tables show approximate guidelines for • After charging the battery pack, disconnect the 60min 2272 101 the length of time the camera can be used AC power adaptor from the multi connector of 8 when you shoot in Normal mode in an the camera. environment where the ambient temperature is 25°C (77°F), and the To remove the battery pack supplied battery pack is fully charged. The guidelines for the number of images that can be recorded or viewed allow for changing the “Memory Stick” as necessary. • When turning the LCD screen off and on, it Actual results may differ slightly from takes about one minute to calculate the proper these, depending on the conditions of use. remaining time. • A proper remaining time may not be indicated depending on conditions of use or circumstances. Battery eject lever Charging time Approximate time to charge a completely discharged battery pack using the AC-LM5 Open the battery/“Memory Stick” cover, AC power adaptor at a temperature of 25°C and push down the battery eject lever in the (77°F). arrow direction as illustrated above. Battery pack Full charge • Be careful not to drop the battery pack when (min.) removing it. NP-FC10 (supplied) Approx.150,

Charging the battery pack (continued)

Shooting still images Viewing still images3) – Using the battery pack that was used In normal shooting1) repeatedly or the battery capacity decreases NP-FC10 (supplied) as time passed (page 105). NP-FC10 (supplied) No. of Battery life No. of Battery life Image size images (min.) The POWER SAVE function Image size images (min.) 2272×1704 Approx. 3 200 Approx. 160 When the POWER SAVE function is 2272×1704 Approx. 140 Approx. 70 640×480 Approx. 3 200 Approx. 160 activated, you can shoot for a longer period 1) Shooting at 30-second intervals with [P. of time. QUALITY] set to [FINE], LCD screen turned 3) Playing back images in order at about 3-second Set the MODE dial to SET UP, and set on, flashed every two shootings and turned on/ intervals on the single-image screen with the off every ten shootings. LCD screen turned on. [POWER SAVE] in (SETUP 1) to [ON]. The factory setting is [ON] In continuous shooting2) Shooting movies4) (page 102). • The [POWER SAVE] item is only shown when NP-FC10 (supplied) NP-FC10 (supplied) using the battery pack. Image LCD No. of Battery LCD screen ON LCD screen OFF size screen images life (min.) (min.) (min.) When the POWER SAVE function is activated 2272×1704 ON Approx. 1 400 Approx. 70 Approx. 70 min Approx. 100 min • The LCD screen will be darker than it is when OFF Approx. 2 000 Approx. 100 4) Continuous shooting with an image size of [POWER SAVE] is set to [OFF]. You cannot 640×480 ON Approx. 1 400 Approx. 70 160×112 change the settings for [LCD BACKLIGHT] at this time (page 102). OFF Approx. 2 000 Approx. 100 • The battery life and the number of images • When shooting sill images, the focus works 2) Shooting at about 3-second intervals with [P. recordable or playable are decreased under the only while the shutter button is pressed down following conditions: halfway.QUALITY] set to [STANDARD] and the flash set to (No flash). – At low temperature. – Using the flash. – Turning on and off frequently. – When [LCD BACKLIGHT] is set to [BRIGHT] – When [POWER SAVE] is set to [OFF]. – During Bluetooth connection,

Using an external power source

AC power adaptor Getting started DC plug 1 Multi connector , Connect the AC-LM5 AC power adaptor (supplied) to the multi connector of the camera. When placing the camera, make sure the LCD screen is facing up. Connect the plug with the v mark facing down. • Remove the battery pack when using an external power source. • Connect the AC power adaptor to an easily accessible wall outlet (wall socket) close by. If some trouble occurs while using the adaptor, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket). 2 To a wall outlet (wall socket) Power cord 2 (mains lead) , Connect the power cord (mains lead) to the AC power adaptor and to a wall outlet (wall socket). • When you have finished using the AC power adaptor, disconnect it from the multi connector of the camera. • The set is not disconnected from the AC power source as long as it is connected to the wall outlet (wall socket), even if the unit itself has been turned off.

Using your camera

abroad Power sources You can use your camera in any country or area with the supplied AC power adaptor within 100 V to 240 V AC, 50/60 Hz. Use a commercially available AC plug adaptor [a], if necessary, depending on the design of the wall outlet (wall socket) [b]. AC-LM5 • Do not use an electrical transformer (travel converter), as this may cause a malfunction.,

Turning on/off your camera

There are following two ways to turn on the 2 Rotate the lens portion. The Auto Power Off function camera. Rotating the lens portion in the arrow If no tasks are performed for a while* when shooting, viewing images, or setting up the 1 Press POWER. direction turns on the camera. To turn off the power, rotate it back. camera while using the battery pack, power is automatically shut off to preserve battery

MODE

POWER power. POWER lamp However, in the following circumstances, POWER even if the battery pack is being used to power the camera, the Auto Power Off function will not work. • Movies are being played back • A slide show is being shown • During USB connection • During Bluetooth connection. (When the camera is in remote camera mode, the The POWER lamp lights in green and the camera turns off after three hours.) power is on. When you turn on the camera for the first time, the CLOCK SET screen * When [POWER SAVE] is set to [ON]: appears (page 18). approximately 90 seconds When [POWER SAVE] is set to [OFF]: approximately three minutes To turn off the power Press POWER again, the POWER lamp goes out, and the camera turns off. • To turn off the start-up sound, set [BEEP] to [OFF] in (SETUP 1) in the SET UP settings (page 102).,

How to use the control button

Getting started 2272x1704 2272 ( 3 : 2 ) 1600x1200 1280x 960 640 x 480 IMAGE SIZE MODE

VOICE

E-MAIL

NORMAL

REC MODE To change the current settings of the camera, bring up the menu or the SET UP screen (page 44), and use the control button to make the changes. For each item, press v/V/b/B to select the desired value, then press z or b/B to make the setting.,

Setting the date and time

MODE MODE POWER POWER MODE dial CLOCK SET Y/M/D CLOCK SET Y/M/D M/D/Y M/D/Y D/M/Y D/M/Y 2002 / 1 / 1 12 : 00OK2002 / 1 / 1 12 : 00OKAM AM CANCEL CANCEL OK OK

POWER

123, Set the MODE dial to . , Press POWER to turn on the , Select the desired date format power. with v/V on the control button, • You can carry out this operation even when the then press z. MODE dial is set to P, SCN, , or . The POWER lamp lights in green and the • To set the time and the date again, set the CLOCK SET screen appears on the LCD You can select from [Y/M/D] (year/month/ MODE dial to SET UP, select [CLOCK SET] screen. day), [M/D/Y], and [D/M/Y]. in (SETUP 2) (page 102), then proceed from Step 3. • If the rechargeable button battery, which provides the power for saving the time data, ever loses its charge (page 103), the CLOCK SET screen automatically reappears. If this happens, start from Step 3 to set up the date and time again., Getting started CLOCK SET Y/M/D CLOCK SET Y/M/D CLOCK SET Y/M/D M/D/Y M/D/Y M/D/Y D/M/Y D/M/Y D/M/Y 2002 / 1 / 1 12 : 00OK2003 / 1 / 1 12 : 00OK2003 / 7 / 4 10 : 30OKAM AM AM CANCEL CANCEL CANCEL OK OK OK456, Select the year, month, day, , Set the desired numerical , Select [OK] with B on the hour, or minute item you want value with v/V on the control control button, then press z. to set with b/B on the control button, then press z. The date and time are set and the clock will button. After setting the current numerical value, start to keep time. A v will be shown above, andaVwill be set the next item. Repeat the above process shown below the item currently selected to until all of the items have been set. • To cancel the setting process, select [CANCEL], then press z. be set. • If you select [D/M/Y] in Step 3, set the time on a 24- hour cycle.,

Shooting still images Inserting and removing a “Memory Stick”

Access lamp Connector side12Label side 3 , Open the battery/“Memory , Insert the “Memory Stick.” , Close the battery/“Memory

Stick” cover. Stick” cover.

Insert the “Memory Stick” all the way in Slide the cover in the direction of the arrow. until it clicks as shown in the illustration. To remove the “Memory Stick” Open the battery/“Memory Stick” cover, • For more information about the “Memory • Whenever you insert a “Memory Stick,” push it then push the “Memory Stick” to pop it out. Stick,” see page 104. as far as it can go. If you do not insert it correctly, a proper recording or playback may • Whenever the Access lamp is lit, the not be carried out. camera is recording or reading out an image. Never remove the “Memory Stick” or turn off the power at this time. The data may be corrupted.,

Setting the still image size The MODE dial position during

Shooting still images still image shooting 2272x1704 When shooting still images, the selectable 2272 ( 3 : 2 ) 1600x1200 shooting modes are as follows: 1280x 960 2272x1704 640 x 480 2272 2272 ( 3 : 2 ) IMAGE SIZE MODE 2272x1704 1600x1200 2272 ( 3 : 2 ) 1280x 960 (Auto mode shooting) 1600x1200 1280x 960 640 x 480 640 x 480 You can perform an easy shooting since this MODE IMAGE SIZE MODEIMAGE SIZE mode automatically adjusts the focus, MENU 2 exposure, and white balance. In this mode, 1 [MODE] is set to [FINE] and the AF range

Set the MODE dial to , rotate finder is set to the Multipoint AF (page 22)., , Select (IMAGE SIZE) with b

the lens portion to turn on the on the control button. P (Program mode shooting) power, then press MENU. Select the desired image size You can set the shooting functions in the The menu appears. with v/V. menu settings according to your shooting condition (page 96). The image size is set. • You can carry out this operation even when the After the setting is completed, press MODE dial is set to P or SCN. SCN (Scene selection) • For more information about the image size, see MENU. The menu disappears from the This mode is effective when shooting night page 34. screen. scenes, people at night, landscapes, or • For more information about the [MODE] item portraits (page 31). in the menu, see page 96. • The image size value selected here is preserved even when the camera is turned off.,

Basic still image shooting – using auto mode MODE

POWER 60min 640 FINE 101 MODE dial 98 F2.8 AE/AF lock indicator123Flashes in green t Remains on , Set the MODE dial to , and , Hold the camera steadily with , Press and hold the shutter rotate the lens portion to turn both hands and position a button halfway down. on your camera. subject in the center of the The camera beeps. When the AE/AF lock focus frame. When a “Memory Stick” is inserted, the indicator stops flashing and remains on, the recording folder name is indicated on the Do not cover the lens, flash, or microphone camera is ready for shooting. (The screen LCD screen for about five seconds (page 8) with your fingers. may be frozen for a split second depending (page 55). on the subject.) • If you release your finger from the shutter button, shooting will be canceled. • The minimum focal distance to a subject is 50 cm (19 11/16 inches). To shoot subjects at distances closer than this, use the Macro mode (page 25). • The frame appearing on the LCD screen shows the focus adjustment range. (For more details on the AF range finder, see page 45.),

About Auto Focus

Shooting still images 60min 640 101 , Press the shutter button fully down. The shutter clicks, the shooting is completed, and the still image is saved in the “Memory Stick.” When the recording lamp goes out, you can shoot the next image. • When you are shooting with the battery pack, if no tasks are performed for a while with the camera turned on, power is automatically shut off to preserve battery power (page 16). When you try to shoot a subject that is hard to focus on, the AE/AF lock indicator will change to flashing slowly. The Auto Focus function may be difficult to use with in the following subjects. In such cases, release the shutter button, then try to recompose the shot and focus again. • The subject is distant from the camera and dark • The contrast between the subject and its background is poor • The subject is seen through glass, such as a window • A fast-moving subject • The subject has a reflection, such as that from a mirror, or there is a luminous body and a lustrous subject • A flashing subject. • A backlit subject There are two methods for Auto Focus function: Multipoint AF and Center AF (page 45). When the MODE dial is set to , The Multipoint AF is automatically selected.

Checking the last image

shot – Quick Review 60min 640 101 8/8

REVIEW

101-0008 20037410:30PM , Press b (7) on the control button. To return to shooting mode, press the shutter button lightly or press b (7) on the control button again. To delete the image displayed on the LCD screen 1 Press MENU to display the menu. 2 Select [DELETE] with B on the control button, then press z. 3 Select [OK] with v on the control button, then press z. The image is deleted.,

Using the smart zoom

• If the LCD screen is turned off, the smart zoom W (wide-angle) T (telephoto) 60min 640 101 60min 640 101 98 98 , Press the SMART ZOOM to choose the desired zoom position, and shoot your image. You can zoom in the image using digital process, with very little deterioration. The maximum zoom scale depends on the image size. 1600×1200: 1.4× 1280×960: 1.7× 640×480: 3.5× When the image size is 2272×1704 or 2272 (3:2), the smart zoom does not work. • When using the smart zoom, the image on the LCD screen may look rough. However, this phenomenon has no effect on the recorded image. function does not work. Turn on the LCD screen when using the smart zoom function. • AF range finder is not shown when using the smart zoom. When 9 (FOCUS) is set to [MULTI AF] or [CENTER AF], or flashes and the centrally-located subject has priority to focus on. • The smart zoom cannot be used while shooting movies (page 66).,

Shooting close-ups – Macro

Shooting still images 60min 640 101 60min 640 101 98 9712For close-ups of small subjects like flowers , Set the MODE dial to , and , Center the subject in the frame, or insects, shoot using the macro feature. press B ( ) on the control and shoot the image. You can use this feature for close-ups of button. subjects up to approximately 10 cm To return to normal shooting (3 15/16 inches) from the end of the lens. The (Macro) indicator appears on the Press B ( ) on the control button again. LCD screen. The indicator disappears from the LCD screen. • If the menu is currently displayed, press MENU first to make the menu disappear. • Use the LCD screen to shoot when • You can carry out this operation even when the using the Macro feature. If you use the MODE dial is set to P, SCN (other than the finder, the limits of what you see and Landscape mode) (page 31), or . what you actually shoot may be different.,

Using the self-timer

min 101 60 640 , Set the MODE dial to , and press V ( ) on the control button. The (Self-timer) indicator appears on the LCD screen. • If the menu is currently displayed, press MENU first to make the menu disappear. • You can carry out this operation even when the MODE dial is set to P, SCN, or . 60min 640 FINE 101 F2.8 , Center the subject in the frame, and press the shutter button fully down. The Self-timer lamp (page 8) will flash in orange, and you will hear a beeping sound. The image will be shot after approximately 10 seconds. To cancel the self-timer during the operation Press V ( ) on the control button again. • If you stand in front of the camera and press the shutter button, the focus and the exposure may not be correctly set.

Rotating the lens

– Mirror mode , Adjust the lens portion angle. When shooting in mirror mode, turn over the lens portion as illustrated above. The image on the LCD screen is a mirror-image. However, the image can be normal when recorded. Image on the Recorded image LCD screen,

Selecting a flash mode

• The recommended distance using the flash is 60min To reduce “red-eye” when 640 101 Shooting still images 98 about 0.5 m to 1.7 m (1 foot 7 3/4 inches to shooting live subjects 5 feet 7 inches) when [ISO] is set to [AUTO]. (When the MODE dial is not set to P, [ISO] The flash pre-strobes before shooting to is set to [AUTO].) reduce the red-eye phenomenon. Set [RED • If the menu is currently displayed, press MENU EYE REDUCTION] to [ON] in the SET UP first to make the menu disappear. settings (page 101). appears on the • In the Auto or (Forced flash) mode, you look at the LCD screen in a dark place, you may LCD screen. notice some “noise” in the image, but this will have no effect on the image you shoot. • While the flash is being charged, the /CHG lamp flashes. After charging is completed, the , Set the MODE dial to , and lamp goes out. press v ( ) on the control button repeatedly to selectamflash mode. The flash mode has the following features. No indicator (Auto): Based on the lighting conditions, the camera will decide if there is enough light, and will use the flash accordingly. • The amount of red-eye reduction possible (Forced flash): The flash will be used varies according to the individual. In addition, regardless of the amount of ambient light. the distance to the subject, and whether or not the subject has seen pre-strobe light begin to (No flash): The flash will not be used. strobe may also reduce the effectiveness of the red-eye reduction process. • You can carry out this operation even when the MODE dial is set to P, SCN (Soft snap mode), or (Clip motion).,

Selecting a flash mode (continued) Shooting with the AF • When 9 (FOCUS) is set to [MULTI AF] or

illuminator [CENTER AF], the AF range finder is not displayed. or flashes and the centrally- This is additional lighting provided to assist located subject has priority to focus on. in focusing when shooting in dark places. • In the following Scene selection modes Set [AF ILLUMINATOR] to [AUTO] in (page 31), the AF illuminator will not function. the SET UP settings (page 101). If you try – When shooting in Twilight mode – When shooting in Landscape mode to shoot under insufficient lighting • The AF illuminator is a bright light. There are conditions, ON appears the LCD screen; the no safety hazards, but when shooting at short AF illuminator will flash automatically distances, do not aim it directly at the subject’s during the time between when the shutter eyes. button is pressed halfway down and the focus locks. 60min 640FINE 101 ON F2.8 • Even when the AF illuminator flashes, but sufficient light does not reach the subject (the recommended distance for this feature is up to approx. 1.5 m (4 feet 11 1/8 inches), or the subject has weak contrast, the camera may not focus properly. • If AF illuminator light misses the center of the image somewhat, the camera will focus properly as long as it reaches the subject. • When the focus preset distance is set (page 47), the AF illuminator does not function.,

Shooting with the finder

All of the indicators are turned off Shooting still images Finder DSPL/LCD r ON/OFF The LCD screen is turned off. r All of the available indicators are turned on. The finder is convenient when you want to 60min 640 101 save battery power, or when it is difficult to confirm the image using the LCD screen. Each time you press DSPL/LCD ON/OFF, the display changes in the following order. • The image through the finder does not indicate the actual recordable range. To confirm the recordable range, use the LCD screen. • For details on the items displayed, see page 108. • Just as with the AE/AF lock indicator on the LCD screen, when the AE/AF lock lamp of the finder section stops flashing and remains on, you can start shooting (page 22). • When the LCD screen is turned off, the smart zoom does not function (page 24). • If you press (Flash mode)/ (Self-timer)/ (Macro) with the LCD screen turned off, the image will be displayed on the screen for approximately two seconds so you can check or change the setting.,

Inserting the date and time on a still image CAMERA

CAMERA CAMERA MOVING IMAGE: MPEG MOVIE MOVING IMAGE: DAY&TIME MOVING IMAGE: MPEG MOVIE DATE/TIME: OFF DATE/TIME: DATE DATE/TIME: DATE RED EYE REDUCTION: OFF RED EYE REDUCTION: OFF RED EYE REDUCTION: OFF AF ILLUMINATOR: AUTO AF ILLUMINATOR: AF ILLUMINATOR: AUTO

SELECT

OK PAGE SELECT123, Set the MODE dial to SET UP. , Select (CAMERA) with v on , Select the date and time setting

The SET UP screen appears. the control button, then press with v/V on the control button, B. then press z.

• When images are shot with the date and time Select [DATE/TIME] with v/V, DAY&TIME: Inserts the date and the time inserted, the date and time cannot be removed then press B. later. of shooting into the image • When shooting images with the date and time DATE: Inserts the year, the month and the inserted, the actual date and time are not date of shooting into the image displayed on the LCD screen, instead, is OFF: Does not insert date/time data into the displayed in the upper left portion of the LCD image screen. The actual date and time are indicated After the setting has been completed, set the in red in the lower-right corner when the image is played back. MODE dial to , and continue your shooting. • When you chose [DATE] in Step 3, the date will be inserted in the order set in “Setting the date and time” (page 18). • You can insert the date and time even when the MODE dial is set to P or SCN. • This setting is maintained even when the power is turned off.,

Shooting according to scene conditions

(scene selection) Shooting still images Twilight mode Twilight portrait mode Landscape mode Soft snap mode When shooting night scenes, shooting people at night, shooting landscapes, or Twilight portrait mode Soft snap mode shooting portraits, use the modes listed Use this mode when shooting people in the The soft snap mode lets you shoot skin below to increase the quality of your foreground at night. colors in brighter and warmer tones for images. Because the shutter speed is slow, it is more beautiful pictures. In addition, the soft recommended that you use a tripod. focus effect creates a gentle atmosphere for

Twilight mode • Allows you to shoot images of people in the portraits of people, flowers, etc.foreground with distinct outlines without losing

Under dark lighting conditions, you can the feeling that you are shooting at night. shoot using the Twilight mode, and still get • The flash forcely strobes. good images. However, because the shutter speed is slower under these conditions, we Landscape mode recommend you use a tripod. Focuses on images far away, so is • The flash cannot be used. convenient for shooting landscapes at a distance. • You cannot shoot in Macro mode. • The flash auto mode cannot be selected.,

Shooting according to scene conditions (scene selection) (continued)

0EV 0EV SCN EV WB SCN WB SCN WB

MENU

123, Set the MODE dial to SCN, and , Select [SCN] with b on the , Select the desired mode with press MENU. control button. v/V on the control button. The menu appears. The mode is set to your choice. When the setting is completed, press MENU. The menu disappears from the screen. To cancel the scene selection Set the MODE dial to another position. • The setting is maintained even when the power is turned off.,

NR slow shutter

Shooting still images The NR slow shutter mode removes noise from recorded images, providing clear images. When the scene selection mode and shutter speed value are as follows, the camera automatically enters the NR slow shutter mode and “NR” is indicated next to the shutter speed indicator. Mode Twilight/Twilight portrait Shutter 1/2 sec./slower than 1/2 sec. speed Press the shutter button fully F2.8 down. NR2'' r Then the screen turns black.

CAPTURING

r Finally, when “PROCESSING” disappears, PROCESSING the image has been recorded. • To eliminate the effects of vibration, use of a tripod is recommended.

Deciding the still image quality

0EV 0EV EV WB ISO 1 MENU , Set the MODE dial to P, rotate the lens portion to turn on the power, then press

MENU.

The menu appears. • You can carry out this operation even when the MODE dial is set to SCN.

FINE FINE STANDARD

P.QUALITY MODE PFX , Select (P. QUALITY) with b/

B on the control button. Select the desired image

quality with v/V. The image quality is set. After the setting is completed, press MENU. The menu disappears from the screen. • For image quality, you can choose either [FINE] or [STANDARD]. • The image quality value selected here is preserved even when the camera is turned off.,

Image size and quality

You can choose image size (number of The number of images that can be saved in a “Memory Stick”** pixels) and image quality (compression ratio) based on the kind of images you want to shoot. The larger you make the image size and the higher you make the image quality, the better your image, but also the larger the amount of data needed to preserve your image. This means you can save fewer images in your “Memory Stick.” Choose an image size and quality level appropriately for the kind of images you want to shoot. You can resize the images later (Resize function, see page 63). You can choose image size from among the five options in the following tables. Image size Examples 2272×1704 Very fine prints 2272 (3:2) 3:2 prints* 1600×1200 Printing A4 size images 1280×960 Printing postcard size images 640×480 Creating your home page * This option records images in a horizontal to vertical proportion of 3:2 to match the size of the print paper used. The number of images that can be saved in FINE (STANDARD) mode are shown below. (Units: number of images) Capacity 16MB 32MB 64MB 128MB Image size 2272×1704 8 (14) 16 (30) 32 (60) 65 (121) 2272 (3:2) 8 (14) 16 (30) 32 (60) 65 (121) 1600×1200 16 (30) 33 (61) 66 (123) 133 (246) 1280×960 24 (46) 50 (93) 101 (187) 202 (376) 640×480 97 (243) 196 (491) 394 (985) 790 (1 975) **When [REC MODE] is set to [NORMAL] For the number of images that can be saved in other modes, see page 95. • When the images are viewed on the LCD screen of the camera, they all look the same size. • Number of shooting images can differ from these values according to shooting conditions. • The image size value (e.g., 2272×1704) is the number of pixels displayed.,

Viewing still images Viewing images on the LCD screen of your

camera Viewing still images Single Index (single-image) screen (nine-ima 60min 640 101 8/9 101-0008 20037410:30PM BACK/NEXT VOLUME SINGLE DISPLAY You can view images shot with the camera almost immediately on the screen. You can select the following three methods for viewing images. Single (single-image) screen You can view one image at a time, occupying the entire screen. Index (nine-image) screen Nine images are displayed simultaneously in separate panels on the screen. Index (triple-image) screen Three images are displayed simultaneously in separate panels on the screen. Various image information items are also displayed. Index ge) screen (triple-image) screen APERTURE VALUE: F2.8 SHUTTER SPEED: 1/30 EXPOSURE VALUE: 0.0 ISO: 100 101-0002 20037410:30PM MOVE SINGLE DISPLAY • For details on the movies, see page 67. • For a detailed description of the screen indicators, see page 110.

Viewing on the single-image

screen 60min 640 101 8/9 101-0008 20037410:30PM BACK/NEXT VOLUME , Set the MODE dial to , and turn on the power. The newest image in the selected recording folder (page 56) is displayed.,

Viewing on the single-image

screen (continued) 60min 640 101 3/9 101-0003 20037410:30PM BACK/NEXT VOLUME , Select the desired still image with b/B on the control button. b : Displays the previous image. B : Displays the next image.

Viewing on the index (nine- or triple-image) screen

SINGLE DISPLAY MOVE , Press the SMART ZOOM W button once. The display switches to the Index (nine- image) screen. To display the next (previous) Index screen Press v/V/b/B on the control button to move the yellow frame up/down/left/right. APERTURE VALUE: F2.8 SHUTTER SPEED: 1/30 EXPOSURE VALUE: 0.0 ISO: 100 101-0002 20037410:30PM SINGLE DISPLAY , Press the SMART ZOOM W button once more. The display switches to the Index (triple- image) screen. Pressing v/V on the control button shows the remaining image information. To display the next (previous) Index screen Press b/B on the control button. To return to the single-image screen Press the SMART ZOOM T button repeatedly, or press z on the control button.,

Viewing images on a TV screen

A/V connecting cable (supplied) Viewing still images USB ON/OFF switch A/V OUT 1 (MONO) jack23TV/Video switch , Connect the supplied A/V , Install the camera to the USB , Turn on the TV, and set the TV/ connecting cable to the A/V cradle. Video switch to “Video.”

OUT (MONO) jack of the USB

Install the camera as illustrated above. cradle and the audio/video • The name and location of this switch may differ depending on your TV. input jacks of the TV. • Make sure the camera is securely installed to the USB cradle. If your TV has stereo type input jacks, connect the audio plug (black) of the A/V connecting cable to the Lch audio input jack. • When the USB cable is connected to the USB cradle, set the USB ON/OFF switch of the USB cradle to “OFF.” • Turn off both the camera and the TV before connecting the camera and the TV with the A/V connecting cable.,

Viewing images on a TV screen (continued)

Watching images on a TV screen SECAM system 640 If you want to view images on a TV, you Bulgaria, France, Guiana, Hungary, Iran, 101 2/9 need a TV having a video input jack and the Iraq, Monaco, Poland, Russia, Ukraine, etc. A/V connecting cable (supplied). The color system of the TV must match as 101-0002 20037410:30PM BACK/NEXT VOLUME that of your digital still camera. Check the following list: NTSC system 4 Bahama Islands, Bolivia, Canada, Central America, Chile, Colombia, Ecuador, , Set the MODE dial to , and Jamaica, Japan, Korea, Mexico, Peru, turn on the camera. Surinam, Taiwan, the Philippines, the U.S.A., Venezuela, etc. Press b/B on the control button to select the desired image. PAL system Australia, Austria, Belgium, China, Czech • When using the camera abroad, it may be necessary to switch the video output signal to Republic, Denmark, Finland, Germany, match that of your TV system (page 102). Holland, Hong Kong, Italy, Kuwait, Malaysia, New Zealand, Norway, Portugal, Singapore, Slovak Republic, Spain, Sweden, Switzerland, Thailand, United Kingdom, etc. PAL-M system Brazil PAL-N system Argentina, Paraguay, Uruguay,

Deleting still images Deleting images

60min 640 60min 640 Deleting still images 101 2/9 60min 640 1012 9 2/9101 /

DELETE

O K 101-0002 20037410:30PM FOLDER DELETE PROTECT DPOF EXITBACK/NEXT VOLUME OK

OK

1 2 MENU 3 , Set the MODE dial to , and , Press MENU. , Select [OK] with v on the turn on the camera. Select [DELETE] with b/B on control button, then press z.

Select the image you want to the control button, then press

“MEMORY STICK ACCESS” appears on delete with b/B on the control z. the screen. When this message disappears, button. The image has not yet been deleted at this the image has been deleted. point. To delete other images continuously • You cannot delete protected images (page 61). Select the image you want to delete with b/ B on the control button. Select [DELETE], then press z. Next, select [OK] with v on the control button, then press z. To cancel the deletion Select [EXIT] with V on the control button, then press z.,

Deleting on the Index (nine-image) screen

FOLDER DELETE PROTECT DPOF DELETE CANCEL SELECT ALL IN FOLDER SELECT MOVE MENU TO NEXT 1 MENU23, While an Index (nine-image) , Select [SELECT] with b/B on , Select the image you want to screen (page 36) is displayed, the control button, then press delete with v/V/b/B on the press MENU. z. control button, then press z.

Select [DELETE] with b/B on

The (Delete) mark is indicated on the the control button, then press To delete all the images in the folder selected image. At this point, the image has z. Select [ALL IN FOLDER] with B on the not yet been deleted. Put the mark on all control button, then press z. Next, select of the images you want to delete. [OK], then press z. All of the unprotected images in the folder are deleted. To cancel • To cancel your selection, select images you the deletion, select [EXIT], then press z. want to cancel and press z again. The mark disappears., Deleting still images DELETE EXIT OK , Press MENU.

Select [OK] with B on the

control button, then press z. “MEMORY STICK ACCESS” appears on the screen. When this message disappears, all of the images with marks have been deleted. To cancel the deletion Select [EXIT] with b on the control button, then press z.

Deleting on the Index (triple-image) screen

APERTURE VALUE: F2.8 SHUTTER SPEED: 1/30 EXPOSURE VALUE: 0.0 ISO: 100 101-0002 20037410:30PM SINGLE DISPLAY , While an Index (triple-image) screen (page 36) is displayed, move the image you want to delete to the center with b/B on the control button.

DPOF PROTECT DELETE FOLDER

101-0002 20037410:30PM OK BACK/NEXT 2 MENU , Press MENU.

Select [DELETE] with the v/V

on the control button, then press z. At this point, the image has not yet been deleted.,

Deleting on the Index (triple-image) screen (continued) DELETE

O K

CANCEL

101-0002 20037410:30PM OK BACK/NEXT , Select [OK] with v on the control button, then press z. “MEMORY STICK ACCESS” appears on the screen. When this message disappears, the image has been deleted. To cancel the deletion Select [CANCEL] with V on the control button, then press z.,

Formatting a “Memory Stick”

Deleting still images MEMORY STICK TOOL

FORMAT

FORMAT: O K CREATE REC. FOLDER: CANCEL CHANGE REC. FOLDER: ALL DATA WILL BE ERASED READY? O K

CANCEL OK OK

123, Insert the “Memory Stick” you , Select (MEMORY STICK , Select [OK] with v on the want to format into the camera. TOOL) with v/V on the control control button, then press z.

Set the MODE dial to SET UP, button.

The “FORMATTING” message appears. and turn on the power. Select [FORMAT] with B, then, When this message disappears, the format press B. is complete. • The term “formatting” means preparing a Select [OK] with v , then press “Memory Stick” to record images; this process is also called “initialization.” The supplied z. “Memory Stick” and those available commercially, are already formatted, and can To cancel the formatting be used immediately. • When you format a “Memory Stick,” be Select [CANCEL] with V on the control aware that all of the data in the “Memory button, then press z. Stick” will be permanently erased. Protected images are also erased.,

Before advanced operations Changing menu settings Changing items in the SET How to setup and

operate your camera a Press MENU.

UP screen

The menu appears. a Set the MODE dial to SET UP. This section describes the most frequently 2272 The SET UP screen appears. used menus and the SET UP screen. 2272x1704 CAMERA 2272 ( 3 : 2 ) Control button 1600x1200 MOVING IMAGE: MPEG MOVIE 1280x 960 DATE/TIME: OFF 640 x 480 RED EYE REDUCTION: OFF AF ILLUMINATOR: AUTO MODE dial IMAGE SIZE MODE MENU b Select the setting item you SELECT want to change with b/B on b Select the setting item you the control button. want to change with v/V/b/B on the control button. The frame of the item you select turns

VOICE

E-MAIL yellow.

NORMAL

REC MODE SETUP 1 LCD BRIGHTNESS: The letters and symbols of the item LCD BACKLIGHT: SHUTTERBEEP: O N you select turn yellow. POWER SAVE: OFF

OK

c Select the desired setting with v/V on the control button. c Press z on the control button The frame of the selected setting turns to enter the setting. yellow, and the setting is entered.

To turn off the SET UP screen To turn off the menu display display

Press MENU. Set the MODE dial to anything other than SET UP.,

Advanced still image shooting

Advanced still image shooting b Press MENU. • When you are shooting movies (MPEG movie)

Choosing a focus The menu appears. and you choose Multipoint AF, the distance to

method the center of the screen is estimated as an c Select 9 (FOCUS) with b/B, average, so the AF works even with a certain amount of vibration. The Center AF

MODE dial: P/SCN/ then select [MULTI AF] or automatically focuses only on the center of the

[CENTER AF] with v/V. image, so it is convenient when you want to

Multipoint AF The focus is adjusted automatically. focus only on what you aim at.

• When you use the smart zoom or AF The AF range finder frame widens. The color of the AF range finder frame illuminator, priority AF movement is given to You can do auto fucus shooting just suitable changes from white to green. subjects in or near the center of the frame. In on composition. The number of AF range this case, or flashes and the AF range finders, the position or the width of the AF Multipoint AF finder is not displayed. range finder differs depending on the 60min 640 FINE 101 subject. 98

Center AF

The AF range finder frame is only the center of the frame. Control button Center AF MODE dial 60min 640 FINE 101

MENU

a Set the MODE dial to P,

SCN, or .

,

AF lock shooting using a Compose the shot so that the b Return to the fully composed Center AF subject is centered in the AF shot, and press the shutter

range finder, and press the button fully down. Even if it is difficult to focus in AF shooting because the subject is not in the center of the shutter button halfway down. The shutter clicks, the image will be frame, you can focus in this situation using When the AE/AF lock indicator stops recorded with the proper focus for the Center AF. For example, when you are flashing and remains on, and there is a human subjects. shooting two human subjects, and there is a beeping sound, focus adjustment is 60min 640 FINE 101 gap between them, the camera may focus on completed. 97 the background visible in the gap. In a case like this, use AF lock to ensure the subjects 60min 640 FINE 10198 are in correct focus. F2.8 Shutter button • You can carry out the AF lock adjustment process before you press the shutter button fully AF range finder down. AE/AF lock indicator • When you are using AF lock, you can capture an image with the correct focus even if the subject is at the edge of the frame., Advanced still image shooting c Select 9 (FOCUS) with b/B,

Setting the distance then select the distance to the Adjusting the

to the subject subject with v/V. exposure You can select from the following – Focus preset distance settings. – EV adjustment MODE dial: P/SCN/ 0.5m, 1.0m, 3.0m, 7.0m, ∞ (unlimited MODE dial: P/SCN/ When shooting an image using a previously distance) Used when you want to change the set distance to the subject, or when shooting automatic exposure to one of your own a subject through a net or through window 1.0m choice. The value can be set a range from 7.0m glass, it is difficult to get the proper focus in 3.0m1.0m +2.0EV to –2.0EV, in 1/3EV increments. auto focus mode. In these cases, use of the 0.5mCENTER AF MULTI AF Focus preset is convenient. Control buttonFOCUS WB ISO Control button MODE dial MODE dial To return to auto focus mode

MENU

In step 3, select 9 (FOCUS), then select

MENU

[MULTI AF] or [CENTER AF]. • Focal point information may not show the exact distance. a Set the MODE dial to P, SCN, or . a Set the MODE dial to P, SCN, or . b Press MENU. The menu appears. b Press MENU. The menu appears., c Select (EV) with b/B. Shooting techniques The value of the exposure adjustment Spot light-meteringIn normal shooting, the camera makes is displayed. automatic exposure adjustments. Check the MODE dial: P/SCN/ image to be shot, if it looks like the image below, you should make manual adjustments. Spot light-metering lets you adjust the 0EV If you are shooting a back-lit person or a exposure to the subject even when the snowy scene, make your adjustments in the + subject is backlit or there is strong contrast plus direction; if you are shooting a dark 0EV between the subject and the background. EV WB ISO subject that fills the screen, making your adjustments in the – direction should give the You can aim at a particular point, and meter best results. the light to adjust the exposure for that d Select the exposure point. adjustment value. Select the exposure adjustment value Control button MODE dial with v/V. Shutter button Make your adjustment while

MENU

confirming the brightness of the background of the subject on the LCD Underexposured screen. t Adjust in the + direction

To return to auto adjust mode

Return the exposure adjustment value to 0EV. • When the subject is extremely bright or Appropriate exposure extremely dark, or when you are using the a Set the MODE dial to P, flash, the adjustment may not work. SCN, or . b Press MENU. The menu appears. Overexposed t Adjust in the – direction, Advanced still image shooting c Select (SPOT METER) AUTO (no display) with b/B, then select [ON] with Adjusting color tones The white balance is adjusted v. automatically.– White Balance The Spot light-metering aiming point Control button MODE dial is displayed. MODE dial: P/SCN/ Shutter button When the white balance is set to AUTO, the white balance is set automatically in MENU response to the condition of the subject, and Spot light- the overall color balance is adjusted ON metering OFF accordingly. When you want to fix the aiming point WB SPOT METER ISO conditions under which the image is captured, or when shooting under special d Aim the spot light-metering lighting conditions, you can select the aiming point at the spot you settings manually. want to shoot, then shoot your (Incandescent) a Set the MODE dial to P, image. • Used when shooting, for example, at a SCN, or . party, where the lighting conditions

To cancel spot light-metering change often b Press MENU.

In Step 3, select [OFF]. The spot light- • Used in a studio, or under video lights The menu appears. metering aiming point disappears, and the c Select [WB] (WHITE BAL) with camera returns to normal light-metering. (Fluorescent) b/B, then select the desired Used when shooting under fluorescent lights. setting with v/V. (Cloudy) To return to automatic settings Used when shooting under a cloudy sky. In Step 3, select [AUTO]. (Daylight) • Under fluorescent lights that flicker, even if you choose , the overall color of the image may Used when shooting outdoors, and for show differences from the actual color. shooting at night, under neon lights, for • When the flash is triggered, the manual setting fireworks, sunrise/sunset and twilight. of white balance is cancelled, and the shooting of the image is done in AUTO mode., • You can carry out this operation even when the Shooting techniques Adjusting the flash MODE dial is set to SCN or (Clip Motion The color of the subject that you see will be only). captured according to the lighting level conditions. Under the bright summer sun, everything will appear bluish, under a light MODE dial: P sources like a light bulb, white objects will You can adjust the amout of flash light. appear reddish. The human eye has an excellent ability to adjust. Even when Control button lighting conditions change, the eye can adjust and recognize the correct color almost MODE dial instantly. However, digital still cameras are greatly influenced by light. Normally, this MENU camera adjusts automatically, but if you notice that the color of the entire image seems to be a bit unnatural when replaying an image on the LCD screen, it is recommended that you adjust the white balance. a Set the MODE dial to P. b Press MENU. The menu appears. c Select [ ] (FLASH LEVEL) with b/B, then select the desired setting with v/V. HIGH: Makes the flash level higher than normal. NORMAL: Normal setting. LOW: Makes the flash level lower than normal., Advanced still image shooting Before operation d Shoot one frame.

Shooting multiple Set [MOVING IMAGE] to [CLIP

frames MOTION] in the SET UP settings (pages 44, 101). – Clip Motion MAKING"CLIP MOTION" MODE dial: Control button MODE dial You can shoot a number of still images Shutter button consecutively (GIF animation). Because the MENU e Shoot the next frame. file size is small, these images are ideal for use on a home page, or for attaching to an e- Press the shutter button once to shoot the next frame, then repeat this mail message. operation until you have shot the desired number of frames. • Clip Motion images are restricted to color levels of 256 colors and below. This isafPress z. characteristic of GIF format recording. For this reason, the image quality of some images may All of the frames will be saved in the deteriorate. “Memory Stick.” a Set the MODE dial to . NORMAL (160×120) To delete shot images in the The maximum number of frames you can b Press MENU. midst of shooting shoot in one Clip Motion shot is 10. This is The menu appears. 1 In Steps 4 or 5, press b (7). suitable for use on a home page. c Select (IMAGE SIZE) with b/ Shot images will be played back in , then select the desired order, playback stops when the last MOBILE (120×108) B image is reached. Two frames is the maximum number that mode with v/V. 2 Press MENU, and select either can be shot in Clip Motion in this mode. [DELETE LAST] or [DELETE ALL], This is suitable for use with portable data then press z. terminals. 3 Select [OK], then press z. If you chose • MOBILE mode has strict file size limits, so [DELETE LAST] in Step 2, repeat Steps picture quality falls accordingly. 1 to 3 to delete the images in order, from • For the number of images you can record using the latest one shot. Clip Motion, see page 95., • If you do not complete Step 6, the image will Before operation not be saved in the “Memory Stick.” Up to that Shooting in Multi Set [MOVING IMAGE] to [MULTI point, the image is saved temporarily in the Burst mode BURST] in the SET UP settings (pages 44, camera. • In Clip Motion, the date and time cannot be 101). inserted. – Multi Burst Control button MODE dial • When you view Clip Motion images using the Index screen, the images may appear different MODE dial: Shutter button from the actual image recorded. Pressing the shutter button once records 16 MENU • GIF files made on other cameras may not be frames in a row. This is convenient for displayed correctly on this camera. checking your form in sports, for example. a Set the MODE dial to . b Press MENU. The menu appears. c Select (INTERVAL) with b/

B, then select the desired

between-frame interval with v/

V.

You can choose the between-frame interval from among the following. NTSC: 1/7.5 sec., 1/15 sec., 1/30 sec. PAL: 1/6.3 sec., 1/12.5 sec., 1/25 sec., Advanced still image shooting (For information on NTSC/PAL, see • When Multi Burst images are played back on a page 99.) camera without the Multi Burst feature, the 16 Shooting still images frames will all be displayed at the same time, as part of one image, just as they are on a for e-mail 1/30 computer. • For the number of images that can be recorded, – E-MAIL 1/7.5 see page 95. 1/15 1/30 • The flash cannot be used.

MODE dial: / P/SCN

WB INTERVAL • In Multi Burst, the date and time cannot be You can shoot images and save them in a inserted. file that is small enough (320×240) to attach d Press the shutter button. to an e-mail message. The normal mode image that was selected using the 16 frames will be recorded as one (IMAGE SIZE) item (page 21) is also image (image size: 1280×960). recorded.

To delete shot images Control button MODE dial

When using this mode, you cannot delete Shutter button only certain frames. When you delete MENU images, all 16 of the frames are deleted at the same time. 1 Set the MODE dial to . 2 Press MENU and select [DELETE], then press z. 3 Select [OK], then press z. All of the frames are deleted. • When you play back images recorded in Multi a Set the MODE dial to , P, Burst mode on the camera, the 16 frames will or SCN. be played back in order, with a fixed interval between them. b Press MENU. • If you rotate the lens portion during shooting, The menu appears. the shot images may be upside down. • When the images are played back on a computer, the 16 frames you shot will all be displayed at the same time as part of one image., c Select [MODE] (REC MODE) d Shoot your image. with b/B, then select [E-MAIL] Shooting still images If you press and release the with v/V. with audio files shutter button, sound is recorded for five seconds. d Shoot your image. –VOICE If you hold down the shutter button, sound is recorded until you MODE dial: / P/SCN To return to normal mode release the shutter button for up to 40 In Step 3, select [NORMAL]. You can record still images with audio files. seconds. Control button MODE dial • For instructions on how to attach your images To return to normal mode to an e-mail message, refer to the Help files of Shutter button In Step 3, select [NORMAL]. the e-mail software you are using. MENU • To view images recorded in VOICE mode, carry out the same procedure described in “Viewing movies on the LCD screen” (page 67). a Set the MODE dial to , P, or SCN. b Press MENU. The menu appears. c Select [MODE] (REC MODE) with b/B, then select [VOICE] with v., Advanced still image shooting

Adding special effects Control button MODE dial Selecting a Folder

– Picture Effect Shutter button MODE dial: SET UP

MENU

MODE dial: P/SCN/ Your camera can create multiple folders You can add special effects to bring out the within a “Memory Stick.” You can select contrast in your images. the folder used to store images. When not creating a new folder, “101MSDCF” folder SOLARIZE B&W is selected as the recording folder. You can create folders up to “999MSDCF.” Control button a Set the MODE dial to P, MODE dial SCN, or . MENU Like an illustration In black and white with clearly delineated b Press MENU. bright and dark portions The menu appears. SEPIA NEG.ART c Select [PFX] (P.EFFECT) with b/B, then select the desired mode with v/V.

To cancel Picture Effect

In Step 3, select [OFF]. Colored to look like an Made to look like a • Up to 4000 images can be stored in one folder. old photograph negative image When the folder capacity is exceeded, a new folder is automatically created.,

Creating a new folder Changing the recording

folder a Set the MODE dial to SET UP. a Set the MODE dial to SET UP. b Select (MEMORY STICK b Select (MEMORY STICK

TOOL) with v/V, [CREATE TOOL) with v/V, [CHANGE REC. FOLDER] with B/v/V, and REC. FOLDER] with B/v/V, and

[OK] with B/v , then press z. [OK] with B/v , then press z. The following screen appears. The recording folder selection screen appears. 60min CREATE REC. FOLDER SELECT REC. FOLDER 2/2 FOLDER NAME: 102MSDCF CREATING REC. FOLDER 102MSDCF NO. OF FILES: 0 READY? CREATED: 200375OK1:05:34 AM

CANCEL

OKOK

CANCEL

OK BACK/NEXT c Select [OK] with v , then press z. c Select the desired folder with A new folder is created with a number b/B, and [OK] with v , then one higher than the largest number in press z. the “Memory Stick,” and the folder becomes the recording folder. • You cannot select the “100MSDCF” folder as a recording folder. • Once you create a new folder, you cannot delete • The image is stored in the newly selected the new folder with the camera. folder. • Recorded images are recorded in the newly created folder until a different folder is created To cancel changing the or selected. recording folder

To cancel folder creation Select [CANCEL] in step 2 or 3.

Select [CANCEL] in step 2 or 3.,

Advanced still image viewing

Advanced still image viewing c Select [FOLDER] with b, then On the single screen

Selecting the folder press z. 60min 640

and playing back 101 9/9 d Select the desired folder with images b/B. – Folder SELECT FOLDER 2/2 102 101-0009 20037410:30PMBACK/NEXT VOLUME

MODE dial: FOLDER NAME: 102MSDCFNO. OF FILES: 9

CREATED: 200375Select the folder that images you want to 1:05:34 AM On the Index (nine-image) screen play back are stored. O K

CANCEL

OK BACK/NEXT Control button MODE dial e Select [OK] with v , then press MENU z. SINGLE DISPLAY MOVE

To cancel the selection

In step 5, select [CANCEL]. On the Index (triple-image) screen

To play back images without

selecting the folder APERTURE VALUE: F2.8 SHUTTER SPEED: 1/30 You can play back images from a last-shot EXPOSURE VALUE: 0.0 ISO: 100 one without selecting the folder. If the first

Set the MODE dial to . 101-0001 20037410:30PMa or last image in the folder is displayed, the SINGLE DISPLAY

following icons are indicated on the screen. b Press MENU. : Moves to the previous folder. • When no images are stored in the folder, “NO The menu appears. : Moves to the next folder. FILE IN THIS FOLDER” appears. : Moves to both the previous and next folders.,

Enlarging an image e Press the SMART ZOOM T Enlarging a portion of – Playback zoom button repeatedly, the portion

a still image of the image selected in Step a Set the MODE dial to . 4 will be enlarged.

MODE dial: b Display the image you want to

You can enlarge an image up to five times enlarge. the size of the original image. You can also record the enlarged image as a new file. c Press the SMART ZOOM T button to enlarge the image. Control button SMART ZOOM buttons d Press v/V/b/B repeatedly to select a portion of the image to MODE dial enlarge. Press To cancel enlarged viewingv Press z. • You cannot use Playback zoom with movies Press Press (MPEG movie), or images recorded in ClipbBMotion/Multi Burst modes. • If you press the SMART ZOOM W button when you are viewing images that have not been enlarged, the Index screen will appear (page 36). Press V • The images displayed in Quick Review v: To view a portion of the top of the (page 23) can be enlarged using the procedures image outlined in Steps 3 to 5. V: To view a portion of the bottom of the image b: To view a portion of the left side of the image B: To view a portion of the right side of the image, Advanced still image viewing

Recording an enlarged c Select [SLIDE] with b/B, then

image – Trimming Playing back press z. successive images a After you have viewed an Set the following items with v/V/b/B. image using playback zoom, – Slide show INTERVAL settings press MENU. 3 sec/5 sec/10 sec/30 sec/1 minMODE dial: b Select [TRIMMING] with B, You can play back recorded images in IMAGE then press z. succession, one after another. This is useful FOLDER:Plays back all the images in the selected folder. for checking your images, or for givingacSelect the image size with v/V, ALL:Plays back all the images in the presentation. “Memory Stick.” then press z. Control button The image is recorded, and the screen REPEAT image returns to the size it was before MODE dial ON:Plays the images back repeatedly. enlargement. OFF:Plays through the images one MENU time and then stops. • The trimmed image is recorded in the recording d Select [START] with V/B, then folder as the newest file, and the original image is retained. press z. • The trimmed image may suffer some The slide show begins. deterioration in image quality • You cannot trim to 3:2-sized image.

To cancel the slide show setting

In Step 3, select [CANCEL]. a Set the MODE dial to . To stop slide show playback b Press MENU. Press z, select [EXIT] with B, then press The menu appears. z.,

To skip to the next/previous a Set the MODE dial to , and

image during slide show Rotating still images display the image you want to Press B (next), or b (previous).

MODE dial: rotate.

• The interval settings are just guidelines. The Images shot when holding the camera b Press MENU. actual intervals differ, based on factors like the vertically can be rotated and displayed The menu appears. size of the image. horizontally. c Select [ROTATE] with b/B, then press z. d Select with v , and rotate the image with b/B. e Select [OK] with v/V, then press z.

To cancel the rotation

In Step 4, select [CANCEL]. • Protected images, movies (MPEG movie), or images recorded in Clip Motion/Multi Burst modes cannot be rotated. Control button • You may not be able to rotate images shot with other cameras. MODE dial • Also, when viewing images on a computer, the image rotation information may not be MENU reflected depending on the application software., Still image editing Still image editing

On the single screen On the Index (nine-image) Protecting images

a Set the MODE dial to . screen – Protect b Display the image you want to a Set the MODE dial to , press MODE dial: protect with / . the SMART ZOOM W buttonbBTo prevent accidental erasure of an once to switch to the Index important image, you can protect it. c Press MENU. (nine-image) screen. The menu appears. Control button b Press MENU. d Select [PROTECT] with b/B, MODE dial The menu appears then press z. MENU c Select [PROTECT] with b/B, The image currently being displayed is now protected, and the - (Protect) then press z. mark is indicated on the screen. d Select [SELECT] with b/B, 60min 640 then press z. 101 2/9 e Select the image you want to protect with v/V/b/B, then

PROTECT

EXIT press z. OK BACK/NEXT The green - (Protect) mark is indicated on the selected image. e To protect other images, display the image you want to protect with b/B, then press z. SELECT MOVE MENU TO NEXT

To cancel the protection

In Step 4 or 5, press z again. The - mark disappears., f To protect other images, On the Index (triple-image) To release protection repeat Step 5. screen In Step 4, select the image from which you want to release protection, and press z. g Press MENU. a Set the MODE dial to , press To release protection from all of your h Select [OK] with , then press the SMART ZOOM W button B images, repeat this process for each of them. twice to switch to the Index z. (triple-image) screen. The - mark turns white and the selected image is protected. b Move the image you want to protect to the center with b/B.

To cancel the protection

Select [CANCEL] in Step 4 or select c Press MENU. [EXIT] in Step 8, then press z. The menu appears d Select [PROTECT] with v/V,

To release protection then press z.

In Step 5, with v/V/b/B, select an image The center image is protected, and the for which you want to release protection, - (Protect) mark is indicated on that and press z. The - mark turns gray and image. repeat this operation for all the images for which you want to release protection. Then, press MENU, select [OK], and press z.

DPOF PROTECT DELETE To protect all the images in FOLDER

folder 101-0002 20037410:30PMOK BACK/NEXT In Step 4, select [ALL IN FOLDER], then press z. Next, select [ON], then press z. e To protect other images, move the image you want to protect

To release protection of all the to the center with b/B, and

images in the folder repeat Step 4. In Step 4, select [ALL IN FOLDER], and press z. Then select [OFF], and press z., Still image editing c Press MENU.

Changing image size The menu appears

– Resize d Select [RESIZE] with b/B, then

MODE dial: press z.

You can change the image size ofaeSelect the new size with v/V, recorded image, and save it as a new file. then press z. You can resize to the following sizes. The resized image is recorded in the 2272×1704, 1600×1200, 1280×960, recording folder as the newest file. 640×480 The original image is retained even after To cancel the resizing resizing. In Step 5, select [CANCEL]. Control button • Movies (MPEG movie), or images recorded in MODE dial Clip Motion/Multi Burst modes cannot be MENU resized. • When images are resized from a smaller to a larger size, the image quality will deteriorate. • You cannot resize to 3:2-sized image. • If you try to resize a 3:2-sized image, black bands will appear at the top and bottom of the image. a Set the MODE dial to . b Display the image you want to resize with b/B.,

On the single screen On the Index (nine-image) Choosing images to

print a Set the MODE dial to . screen Display the image you want to a Set the MODE dial to and b – Print (DPOF) mark print with / . press the SMART ZOOMWbBMODE dial: button once to switch to the c Press MENU. Index (nine-image) screen. You can designate certain images to be The menu appears. printed. b Press MENU. This mark is convenient when you want to d Select [DPOF] with b/B, then The menu appears. print images at a shop that conforms with press z. the DPOF (Digital Print Order Format) c Select [DPOF] with B, then The mark is indicated on this standard. image. press z. Control button 60min 640 d Select [SELECT] with b/B, 101 2/9 MODE dial then press z. • You cannot mark using the [ALL IN MENU FOLDER] option.

DPOF EXIT

OK BACK/NEXT e Select the images you want to print with v/V/b/B, then press e To mark other images, display z. the image you want to mark The green mark is indicated on the with b/B, then press z. selected image.

To delete the mark

In Step 4 or 5, press z again. The • You cannot mark movies (MPEG movie) or mark disappears. images recorded in Clip Motion mode. • In E-MAIL mode, the print (DPOF) mark is marked on the normal size image that was SELECT MOVE MENU TO NEXT recorded at the same time. • When you mark images shot in Multi Burst f To mark other images, repeat mode, all the images are printed on one sheet divided into 16 panels. Step 5 for each of them., Still image editing g Press MENU. On the Index (triple-image) To delete the mark screen In Step 4, press z again. h Select [OK] with B, then press The mark disappears. z. a Set the MODE dial to , press The setting of the mark is the SMART ZOOM W button completed. twice to switch to the Index (triple-images) screen.

To delete the mark

In Step 5, select the image you want to b Move the image you want to delete the mark with v/V/b/B, and print to the center with b/B. press z. c Press MENU.

To delete all the marks from The menu appears.

the images in the folder d Select [DPOF] with v , then In Step 4, select [ALL IN FOLDER], then press z. press z. Next, select [OFF], then press z. The mark is indicated on the center image.

To cancel the marking

In Step 4, select [CANCEL], or select [EXIT] in Step 8. DPOF

PROTECT DELETE FOLDER

101-0002 20037410:30PM OK BACK/NEXT e To mark other images, move the image you want to print to the center with b/B, and repeat Step 4., Enjoying movies c Select (IMAGE SIZE) with b/ Indicators on the screen while

Shooting movies B, and select the desired mode you are shooting movies

MODE dial: with v/V. These indicators are not recorded. You can choose from 320 (HQX), Each time you press DSPL/LCD ON/OFF, You can shoot movies (MPEG movies). 320×240, or 160×112. the status of the LCD screen changes as See page 95 for the recording time follows: Indicators OFF t LCD OFF t

Before operation allowed for each image size. Indicators ON. See page 109 for a detailed

Set [MOVING IMAGE] to [MPEG description of the indicated items. d Press the shutter button fully MOVIE] in the SET UP settings (pages 44, 101). down. To shoot close-ups (Macro) “REC” appears on the screen and the Control button MODE dial Set the MODE dial to and follow the camera starts recording the image and procedure on page 25. Shutter button sound. MENU 60min 160 101 To shoot with a self-timer REC 00:00:02[00:10:48] Set the MODE dial to and follow the procedure on page 26. • Be careful not to touch the microphone (page 8) during shooting. • When the capacity of the “Memory Stick” • You cannot use a flash. is used up, recording stops. • In MPEG movie, the date and time cannot be inserted. e Press the shutter button fully DSPL/LCD ON/OFF • You cannot use the smart zoom while shooting down again to stop recording. movies. a Set the MODE dial to . b Press MENU. The menu appears., Enjoying movies b Select the desired movie with To rewind / fast-forward

Viewing movies on b/B. Press b/B while playing back a movie.

the LCD screen Movies are displayed a size smaller To return to normal playback, press z. than still images.

MODE dial: High quality movies

60min 160 You can view movies on the LCD screen of 101 10/10 Movies with the image size “320 (HQX)” 00:00:00 the camera and hear sounds from the appear on the full screen. speaker of the camera. Control button Indicators on the screen while 101_0010 20037410:30PM PLAY BACK/NEXT VOLUME MODE dial you are viewing movies Each time you press DSPL/LCD ON/OFF, c Press z. MENU the status of the LCD screen changes as The movie images and sound are follows: Indicators OFF t LCD OFF t played back. Indicators ON. See page 110 for a detailed B (playback) appears on the LCD description of the indicated items. screen while a movie is playing back. 60min • The procedure for viewing movies on a TV is 160 101 10/10 the same as that for viewing still images 00:00:03 (page 37). Speaker DSPL/LCD ON/OFF Playback bar 101_0010 20037410:30PM STOP REV/CUE VOLUME a Set the MODE dial to .

To stop playback

Press z.

To adjust the volume

Press v/V.,

On the single screen On the Index (nine-image) Deleting movies

a Set the MODE dial to screen . MODE dial: b Select the movie you want to a Set the MODE dial to and You can delete unwanted movies. delete with / . press the SMART ZOOMWbBControl button button once to display an c Press MENU. Index (nine-image) screen. MODE dial The menu appears. MENU b Press MENU. d Select [DELETE] with b/B, The menu appears. then press z. c Select [DELETE] with b/B, The movie has not been deleted yet. then press z. e Select [OK] with v , then press . d Select [SELECT] with b/B, z “MEMORY STICK ACCESS” then press z. appears on the screen. e Select the movies you want to The movie has been deleted when the message disappears. delete with v/V/b/B, then press z. f To delete other movies, display The (Delete) mark is indicated on the movie you want to delete the selected movie. with b/B, then press z.

To cancel the deletion

In Step 5 or 6, select [EXIT]. SELECT MOVE MENU TO NEXT The movie has not been deleted yet., Enjoying movies f Repeat Step 5 to delete other On the Index (triple-image) To cancel the deletion movies. screen In Step 5, select [CANCEL]. g Press MENU. a Set the MODE dial to and Select [OK] with , then press press the SMART ZOOMWhBbutton twice to switch to the z. Index (triple-image) screen. The movies are deleted when the “MEMORY STICK ACCESS” b Move the movie you want to message disappears. delete to the center with b/B.

To cancel the deletion c Press MENU.

In Step 8, select [EXIT]. The menu appears. d Select [DELETE] with v/V, then

To delete all the images in the press z.

folder The movie has not been deleted yet. In Step 4, select [ALL IN FOLDER], then press z. Next, select [OK], then press z. To cancel the deletion, select [EXIT] with b, then press z. DELETEOK

CANCEL

101_0010 20037410:30PM OK BACK/NEXT e Select [OK] with v , then press z. The movie is deleted when the “MEMORY STICK ACCESS” message disappears., Cutting the movie numbered Cutting movies

Editing movies 101_0002

101_0001 101_0003 Control button MODE dial: MODE dial You can cut movies, or delete unnecessary123portions of movies. This is the MENU recommended mode to use when the 101_0002 “Memory Stick” capacity is insufficient, or 1. Cutting scene A. when you attach movies to your e-mail messages. 1A2B3101_0002

The file numbers assigned when DIVIDE point

2. Cutting scene B. movies are cut 101_0004 The cut movies are assigned new numbers and recorded as the newest files in the13A2BaSet the MODE dial to . recording folder. The original movie is deleted and its file number is skipped. 101_0005 b Select the movie you want to DIVIDE point cut with b/B. 3. Deleting scenes A and B if they are unnecessary. c Press MENU. 101_0004 101_0007 The menu appears. 13A2BdSelect [DIVIDE] with B, then press z. Next, select [OK] with 101_0006 DELETE DELETE v , then press z. 4. Only the desired scenes remain. The playback of the movie starts. 132101_0006, Enjoying movies e Decide on a cutting point. • You cannot cut the following images. Deleting unnecessary Press at the desired cutting point. – Clip Motionz portions of movies – Multi Burst 60 – Still imagemin 160 a Cut an unnecessary portion of 101 10/10 – Movies not long enough to cut DIVIDE 00:00:02 – Protected movie a movie (see the previous DIVIDING POINT • You cannot restore movies once you cut them. c C page). O K • The original movie is deleted when you cut it.

CANCEL

EXIT • The cut movie is recorded in the recording b Display the portion of the

OK

folder. movie you want to delete. When you want to adjust the cutting point, select [c/C] (frame c Press MENU. forward/ rewind) and adjust the cutting The menu appears. point with b/ B. If you want to change the cutting point, select [CANCEL]. d Select [DELETE] with b/ B, The playback of the movie starts again. then press z. f When you have decided onaeSelect [OK] with v , then press cutting point, select [OK] with z. v/V, and press z. The movie currently displayed on the screen is deleted. g Select [OK] with v , then press z. The movie is cut.

To cancel cutting

In Step 5, select [EXIT]. The movie appears on the screen again., Enjoying images on your computer

USB mode x Image Transfer Copying images to There are two modes for a USB connection, This application is used to easily transfer

your computer [NORMAL] and [PTP]* modes. The images from the camera to a computer. – For Windows users factory setting is the [NORMAL] mode. x PIXELA ImageMixer * Compatible only with Windows XP. When This application is used to display and edit connected to a computer, only the data in the images that are stored in a computer.

Recommended computer folder selected by the camera is copied to the

environment computer. • This section describes the procedures OS: Microsoft Windows 98, Windows using Windows Me as an example. The 98SE, Windows 2000 Professional, Communication with your required operations may differ depending Windows Millennium Edition, Windows computer on your OS. XP Home Edition, or Windows XP When your computer resumes from the • Close down all applications Professional suspend or sleep mode, communication running on the computer before The above OS must be installed at the between your camera and your computer installing the USB driver and factory. Operation is not assured in an may not recover at the same time. application. environment upgraded to the operating • When using Windows XP or Windows systems described above or in a multi-boot When a USB connector is not 2000, log on as Administrators. environment. provided on your computer • The display settings should be 800 × 600 CPU: MMX Pentium 200 MHz or faster dots or more and High Color (16-bit USB connector: Provided as standard When neither a USB connector nor a color, 65 000 colors) or more. When set Display: 800 × 600 dots or more “Memory Stick” slot is provided, you can to less than 800 × 600 dots or 256 colors High Color (16-bit color, 65 000 colors) or copy images using an additional device. See or less, the install title screen does not more the Sony Website for details. appear. http://www.sony.net/ • If you connect two or more USB equipment to a single computer at the same time, some Contents of the CD-ROM equipment, including your camera, may not operate depending on the type of USB x USB Driver equipment. This driver is needed in order to connect the • Operations are not guaranteed when using a camera to a computer. USB hub. When using Windows XP, you need not • Operations are not guaranteed for all the recommended computer environments install the USB driver. mentioned above., Enjoying images on your computer

Installing the USB driver c Click [Next]. When the Installing “Image Transfer”

“Information” screen appears, When using Windows XP, you need not You can use the “Image Transfer” software install the USB driver. click [Next]. to copy images to your computer Once the USB driver is installed, you need automatically when you connect the camera not install the USB driver. to your computer. a Turn on your computer, and a Click [Image Transfer] on the insert the supplied CD-ROM title screen. into the CD-ROM drive. Select the desired language, Do not connect your camera to then click [OK]. your computer at this time. The “Welcome to the InstallShield The title screen appears. If it does not The USB driver installation starts. Wizard” screen appears. appear, double-click (My When the installation is completed, the Computer) [ImageMixer] in that screen informs you of completion.t order. d Click [Yes, I want to restart my b Click [USB Driver] on the title computer now], then click screen. [Finish]. • This section describes the English screen. The “InstallShield wizard” screen Your computer restarts. Then, you can appears. establish USB connection., b Click [Next]. When “License d Select the folder to be f Click [Finish]. Agreement” screen appears, installed, then click [Next]. click [Yes]. Select the program folder, then Read the agreement carefully. If you click [Next]. accept the terms of the agreement, proceed with the installation. The “Information” screen appears. The “InstallShield Wizard” screen closes. If you wish to continue with the installation of “ImageMixer,” click [PIXELA ImageMixer] on the title screen and then follow the procedure. e Confirm if the checkbox is checked on the “Image • The USB driver is needed in order to use c Click [Next]. Transfer Settings” screen, “Image Transfer.” If the necessary driver is not already installed on your computer, a screen then click [Next]. that asks if you want to install the driver will appear. Follow the instructions that appear on the screen. When the installation is completed, the screen informs you of completion., Enjoying images on your computer

Installing “ImageMixer” c Follow instructions on each Connecting your camera to

succeeding screen. a Click [PIXELA ImageMixer] on your computer the title screen. When installation is complete, the a Turn on your computer. “Read Me” text appears. Read the text, The “Choose Setup Language” screen then close the window by clicking b Insert the “Memory Stick” with appears. at the upper right corner of the screen. the images you want to copy After that, click [Finish] in the install screen to close the install screen. into the camera. Connect the

USB cradle and the AC power

• If DirectX8.0a or a later version is not installed adaptor, and plug the adaptor in your computer, the “Information” screen into a wall outlet (wall socket). appears. Follow the procedure on the screen. “Memory Stick” d Remove the CD-ROM. To a wall AC power outlet adaptor (wall socket) • You can use the “PIXELA ImageMixer for 3 Sony” software to copy, view and edit images. For details, see the software’s help files. b Select the desired language, 2 then click [OK]. 1 • For further details on the AC power adaptor and USB cradle, see page 11. • For further details on the “Memory Stick,” see page 20. The “Welcome to the InstallShield Wizard” screen appears. • This section describes the English screen., c Make sure the USB ON/OFF e Install the camera to the USB • During the USB connection, do not switch is set to “ON” and cradle and turn on the camera. switch the USB ON/OFF switch or not remove the camera from the USB connect the supplied USB cradle. The data may be corrupted. cable to the (USB) jack of When you cancel the USB connection, the USB cradle. see “P To cancel the USB connection” (page 77). USB ON/OFF switch * During communication, the access indicators turn red. • Make sure the camera is securely installed USB cable to the USB cradle. • When using Windows XP, the AutoPlay wizard automatically appears on the d Connect the USB cable to your desktop. Proceed to page 79. computer. USB MODE

NORMAL

Access indicators* “USB MODE NORMAL” appears on the LCD screen of the camera. When a USB connection is established for the first time, your computer automatically runs the used program to recognize the • When using a desktop computer, connect the camera. Wait for a while. USB cable to the USB connector on the rear panel. • If “USB MODE NORMAL” does not appear, confirm that [USB CONNECT] is set to [NORMAL] in the SET UP settings (page 102)., Enjoying images on your computer

P To cancel the USB Copying images using – Windows XP

connection “Image Transfer” Connect the camera and your Removing the USB cable from your computer with the USB cable and the – Windows 98/98SE/2000/Me computer/removing the camera from the USB cradle. USB cradle/turning off the camera Connect the camera and your “Image Transfer” starts up automatically For Windows 2000, Me, or XP users computer with the USB cable and the and the images are automatically copied to USB cradle. the computer. 1 Double-click on the task tray. “Image Transfer” launches and the images Windows XP is set so that the OS AutoPlay 2 Click (Sony DSC), then click [Stop]. are automatically copied to the computer. Wizard activates. 3 Confirm the device on the confirmation When copying is complete, “ImageMixer” If you want to cancel the setting, follow the window, then click [OK]. automatically launches and images appears. procedure below. 4 Click [OK]. a Click [Start], then click [My This step is unnecessary for Windows Computer]. XP users. 5 Remove the USB cable from your b Right-click [Sony computer, remove the camera from the MemoryStick], then click USB cradle or turn off the camera. [Properties]. For Windows 98 or 98SE users c Cancel the setting. Confirm that the access indicators on the 1 Click [AutoPlay]. LCD screen are turned white and carry out 2 Set [Content type] to [Pictures]. only Step 5 above. 3 Check [Select an action to perform] • Normally “Image Transfer” and “Date” folders under [Actions], select [Take no are created inside the “My Documents” folder, action], then click [Apply]. and all of the image files recorded with the 4 Set [Content type] to [Video files] camera are copied into these folders. and proceed step 3. Set [Content • You can change the “Image Transfer” settings type] to [Mixed content] and (page 78). proceed step 3. 5 Click [OK]. The [Properties] screen closes. The OS AutoPlay Wizard does not start up automatically even if the USB connection is made next time.,

Changing “Image Transfer” Copying images without • When you try to copy an image to a folder in

settings using “Image Transfer” which an image with the same file name is stored, the overwrite confirmation message You can change “Image Transfer” settings. – Windows 98/98SE/2000/Me appears. Clicking [Yes] overwrites the image. When not overwriting the image, click [No] or Right-click the “Image Transfer” icon on If you do not set to launch “Image Transfer” change the file name. the task tray, select [Open Settings]. The automatically, you can copy images as settings you can set are as follows: [Basic], following procedure. When a removable disk icon is [Copy], and [Delete]. a Double-click [My Computer], not shown Right-click here then double-click [Removable 1 Right-click [My Computer], then click Disk]. [Properties]. The contents of the “Memory Stick” The “System Properties” screen appears. inserted in your camera appear. • For Windows 2000 users, click the [Hardware] • tab on the “System Properties” screen.This section describes an example of copying When the “Image Transfer” starts, the images to the “My Documents” folder. 2 Confirm if other devices are already below window appears. • When the “Removable Disk” icon is not shown, installed. see the right column. 1 Click [Device Manager]. • When using Windows XP, see page 79. 2 Double-click [ Other Devices]. b Double-click [DCIM], then 3 Confirm if there is a “ Sony double-click the folder that the DSC” or “ Sony Handycam” with a mark. image files you want to copy 3 If you find either of the devices above, are stored. follow the steps below to delete them. The folder opens. 1 Click [ Sony DSC] or [ Sony c Drag and drop the image files Handycam]. 2 Click [Remove]. (In case of into the “My Documents” Windows 2000, click [Uninstall].) When you select [Settings] from the above folder. The “Confirm Device Removal” window, you can only change the [Basic] The image files are copied to the “My screen appears. setting. Documents” folder. 3 Click [OK]. The device is deleted. Try the USB driver installation again using the supplied CD-ROM (page 73)., Enjoying images on your computer – Windows XP e Select [Nothing. I’m finished Viewing the images on your working with these pictures], computer

Copying images using the then click [Next]. Windows XP AutoPlay wizard a Double-click [My Documents] The “Completing the Scanner and

Make a USB connection on the desktop.a Camera Wizard” screen appears. (pages 75 to 76). Click [Copy The “My Documents” folder contents f Click [Finish]. are displayed. pictures to a folder on my The wizard closes. computer using Microsoft • This section describes the procedure for Scanner and Camera Wizard], • When you want to continue copying other viewing images in the “My Documents” folder. then click [OK]. images, carry out “P To cancel the USB • When using Windows XP, double-click [Start] connection” (page 77). Then, follow the t [My Documents] in that order. The “Scanner and Camera Wizard” process from step 1 again. • You can use the “PIXELA ImageMixer for screen appears. Sony” software to view and edit images on your computer. For details, see the software’s help b Click [Next]. files. The images stored on the “Memory b Double-click the desired folder Stick” are displayed. and image file. c Click the checkbox of images The image is displayed. that you do not want to copy to your computer to remove the checkmark, then click [Next]. The “Picture Name and Destination” screen appears. d Select a name and destination for your pictures, then click [Next]. Image copying starts. When the copying is completed, the “Other Options” screen appears.,

Image file storage destinations and file names

The image files recorded with your camera are grouped as folders in the “Memory Stick.” Example: when viewing folders on Windows Me Folder containing image data which was recorded using the camera not equipped with the folder creating function. Folder containing image data which was recorded using your camera. When not creating any folders, there is only the “101MSDCF” folder. Folder containing E-MAIL mode image data/movie data/ VOICE mode audio data which was recorded using the camera not equipped with the folder creating function. • The data stored in the “100MSDCF” or • For more information about the folder, “MSSONY” folder was recorded using see page 55. the camera not equipped with the folder creating function. You cannot record any images to these folders. The images in these folders are available only for viewing., Enjoying images on your computer Folder File name File meaning 101MSDCF to DSC0ssss.JPG • Still image files shot normally 999MSDCF – Multi Burst mode (page 52) • Still image files shot in – E-MAIL mode (page 53) – VOICE mode (page 54) DSC0ssss.JPE • Small-size image files shot in E-MAIL mode. DSC0ssss.MPG • Audio files shot in VOICE mode. CLP0ssss.GIF • Clip Motion files shot in NORMAL mode (page 51) CLP0ssss.THM • Index image files of Clip Motion files shot in NORMAL mode MBL0ssss.GIF • Clip Motion files shot in MOBILE mode (page 51) MBL0ssss.THM • Index image files of Clip Motion files shot in MOBILE mode MOV0ssss.MPG • Movie files shot in MPEG MOVIE mode (page 66) Note on the table • Image file storage destinations and • The meanings of the file names are as file names when using the above: Bluetooth function, see the ssss stands for any number within Bluetooth function operating the range from 0001 to 9999. instructions. • The numerical portions of the following files are the same. – A small-size image file shot in E- MAIL mode and its corresponding image file – An audio file shot in VOICE mode and its corresponding image file – An image file shot with Clip Motion and its corresponding index image file,

USB mode a Installing the USB driver Copying images to There are two modes for a USB connection, 1 Turn on your computer, and set the

your computer [NORMAL] and [PTP]* modes. The supplied CD-ROM into the CD-ROM – For Macintosh users factory setting is the [NORMAL] mode. drive. * Compatible only with Mac OS X. When The “PIXELA ImageMixer for Sony” connected to a computer, only the data in the

Recommended computer folder selected by the camera is copied to the screen appears.

environment computer. 2 Double-click (Setup Menu). OS: Mac OS 8.5.1, 8.6, 9.0, 9.1, 9.2, or 3 Click (USB Driver). Mac OS X (v10.0/v10.1) Communication with your The “USB Driver” screen appears. The above OS must be installed at the computer 4 Double-click the icon of the hard disk factory. For the following models, update When your computer resumes from the containing the OS to open the screen. your OS to Mac OS 9.0 or 9.1. suspend or sleep mode, communication 5 Drag and drop the following two files – iMac with Mac OS 8.6 installed at the between your camera and your computer from the screen opened in step 3 into the factory, and a slot loading type CD-ROM may not recover at the same time. System Folder icon in the screen opened drive in step 4. – iBook or Power Mac G4 with the Mac OS When a USB connector is not • Sony USB Driver 8.6 installed at the factory provided on your computer • Sony USB Shim USB connector: Provided as standard 6 When the message for confirmation is Display: 800 × 600 dots or more When neither a USB connector nor a “Memory Stick” slot is provided, you can shown, click “OK.”32 000-color mode or more 7 Restart the computer and remove the • If you connect two or more USB equipment to copy images using an additional device. See a single computer at the same time, some the Sony Website for details. CD-ROM from the CD-ROM drive. equipment, including your camera, may not http://www.sony.net/ b Connecting your camera to operate depending on the type of USB equipment. your computer • Operations are not guaranteed when using a Steps your OS requires For details, see pages 75 to 76. USB hub. Follow the steps below, according to your • Operations are not guaranteed for all the OS. recommended computer environments mentioned above. OS Steps Mac OS 8.5.1/8.6/9.0 Steps 1 to 4 Mac OS 9.1/9.2/Mac OS X Steps 2 to 4 (v 10.0/v 10.1), Enjoying images on your computer Removing the USB cable from your d Viewing the images on your For Mac OS X users computer, removing the camera computer When you click an E-MAIL mode image from the USB cradle, or turning off file, “There is no application available to the camera 1 Double-click the hard disk icon. open the document "DSC0ssss.JPE".” Drag and drop the drive icon or the icon of 2 Double-click the desired image file in may be shown. In this case, carry out the the “Memory Stick” to the “Trash” icon, the folder containing the copied files. follwing setup. The screen may differ then remove the USB cable, remove the The image file opens. depending on your OS version. camera from the USB cradle, or turn off the 1 Click [Choose Application...] on the camera • You can use the “PIXELA ImageMixer for screen “There is no application available • If you are using Mac OS X, remove the USB Sony” software to copy images to your cable, etc., after you have turned your computer computer and to view images on your to open the document off. computer. For details on installing, see "DSC0ssss.JPE".”. operating instructions supplied with the CD- c Copying images 2 Change [Recommended Applications] ROM. For details on operation, see the software’s help files. to [All Applications]. 1 Double-click the newly recognized icon • “PIXELA ImageMixer for Sony” cannot be 3 Select [QuickTime Player] from the on the desktop. used with Mac OS X. application list, then click [Open]. The contents of the “Memory Stick” • “Image Transfer” cannot be used with inserted in your camera appear. Macintosh. 2 Double-click “DCIM.” 3 Double-click the folder that the images you want to copy are stored. 4 Drag and drop the image files to the hard disk icon. The image files are copied to your hard disk. For details on the storage location of the images and file names, see page 80., Troubleshooting 2 Press the RESET button located inside 3 Consult your Sony dealer or local

Troubleshooting the battery/“Memory Stick” cover, then authorized Sony service facility.

turn on the power again. (This will clear If you have trouble with your camera, try the date and time settings, etc.) the following solutions. (When using the Bluetooth function, see the Bluetooth function operating RESET instructions.) 1 Check the items on pages 84 to 91. If the screen shows “C:ss:ss”, the self-diagnosis function is working. Please see page 94.

Battery and power

Symptom Cause Solution The battery pack is not • The camera is turned on. p Turn the power off (page 16). charged. • The connection is not correct. p Check the connection (page 11). The battery pack cannot • The battery pack is not properly installed. p Install the battery pack while pushing the battery eject lever be installed. down using the front edge of the battery pack (page 11). /CHG lamp flashes. • The battery pack is not properly installed. p Properly install the battery pack (page 11). • The battery pack malfunctions. p Consult your Sony dealer or local authorized Sony service facility. While charging the battery • The AC power adaptor is disconnected. p Properly connect the AC power adaptor (page 11). pack, the /CHG lamp • The camera is not properly installed to the USB p Properly install the camera (page 10). does not light. cradle. • The battery pack is not properly installed. p Properly install the battery pack (page 11). • The charging is complete. —, Troubleshooting Symptom Cause Solution The battery remaining • You have used the camera for a long time in an — indicator is incorrect. Or extremely hot or an extremely cold location. the sufficient battery • The battery pack is dead (page 105). p Replace the battery pack with a new one. remaining indicator is • The battery pack is discharged. p Replace the battery pack with a charged one (page 11). displayed but the power • A mismatch has occurred in the remaining p Fully charge the battery pack (page 11). runs out soon. battery time information. The battery pack runs • You are shooting/viewing images in an — down too quickly. extremely cold location. • The battery pack is not charged enough. p Fully charge the battery pack (page 11). • The battery pack is dead (page 105). p Replace the battery pack with a new one. The power cannot be • The battery pack is not installed properly. p Properly install the battery pack (page 11). turned on. • The camera is not properly installed to the USB p Properly install the camera (page 10). cradle. • The AC power adaptor is disconnected. p Connect the AC power adaptor securely to the camera (page 15). • The battery pack is dead (page 105). p Replace the battery pack with a new one. • The battery pack is not charged enough. p Fully charge the battery pack (page 11). The power turns off • If you do not operate the camera for about 90 p Turn on the power again (page 16). suddenly. seconds while the power is on, the camera turns off automatically to prevent wearing down the battery (when [POWER SAVE] is [OFF], after three minutes.) (page 16). • The battery pack is discharged. p Replace the battery pack with a charged one (page 11). • The camera is not properly installed to the USB p Properly install the camera (page 10). cradle.,

Shooting still images / movies

Symptom Cause Solution The LCD screen is not • The power was turned off with the LCD screen p Turn on the LCD screen (page 29). turned on even when the turned off the last time you used the camera. power is turned on. The subject is not visible • The MODE dial is not set to , P, SCN, or p Set the MODE dial to , P, SCN, or, (pages 22, 31, 66). on the LCD screen.The image is out of focus. • The subject is too close. p Set the macro recording mode. Make sure to place the lens farther away from the subject than the shortest shooting distance when shooting (page 25). • The Landscape mode is selected for Scene p Cancel the mode (page 31). selection. • You set the focus preset distance. p Set to the auto focus mode (page 47). Unable to smart zoom. • You cannot use smart zoom while shooting a — movie (MPEG movie). • The LCD screen is turned off. p Turn on the LCD screen (page 29). • The (IMAGE SIZE) is set to [2272×1704] or p Set (IMAGE SIZE) to other settings except [2272×1704] [2272 (3:2)]. and [2272 (3:2)] (page 24). The image is too dark. • You are shooting a subject with a light source p Adjust the exposure (page 47). behind the subject. • The brightness of the LCD screen is too low. p Adjust the brightness of the LCD screen (page 102). • [POWER SAVE] is set to [ON]. p Set [POWER SAVE] to [OFF] (page 102). The image is too bright. • You are shooting a spot lighted subject in a dark p Adjust the exposure (page 47). location such as on a stage. • The LCD screen is too bright. p Adjust the brightness of the LCD screen (page 102). The image is • [PFX] (P. EFFECT) is set to [B&W]. p Cancel the B&W mode (page 55). monochrome (black and white). Vertical streaks appear • The smear phenomenon is occurring. p This is not a malfunction. when you are shooting a very bright subject., Troubleshooting Symptom Cause Solution You cannot shoot images. • No “Memory Stick” is inserted. p Insert a “Memory Stick” (page 20). • The capacity of the “Memory Stick” is p Delete the images saved in the “Memory Stick,” or format it. insufficient. p Change the “Memory Stick.” • The write-protect switch on the “Memory Stick” p Set the write-protect switch to the recording position is set to the LOCK position. (page 104). • You cannot shoot while the flash is charging. — • The MODE dial is not set to , P, or SCN p Set the MODE dial to , P, or SCN (pages 22, 31). when you want to shoot a still image. • The MODE dial is not set to when you want p Set the MODE dial to (page 66). to shoot a movie. Cannot shoot images with • The MODE dial is set to or SET UP. p Set it to a setting other than , or SET UP (page 27). the flash. • The flash is set to (No flash). p Set the flash to “Auto” (No indicator) or (Forced flash) (page 27). • When shooting still images, scene selection is p Cancel the Twilight mode (page 31). set to the Twilight mode. • [MOVING IMAGE] is not set to [CLIP p Set it to [CLIP MOTION] (page 51) MOTION] in the SET UP settings. The eyes of the subject — p Set [RED EYE REDUCTION] to [ON] (page 27). come out red. The date and time are • The date and time are not set correctly. p Set the correct date and time (page 18). recorded incorrectly.

Viewing images

Symptom Cause Solution The image cannot be • The MODE dial is not set to . p Set the MODE dial to (page 35). played back. • You cannot play back the image on the camera, — if it is modified on a computer or its folder/file name is changed. • The camera is in USB mode. p Cancel USB communication (page 77) and set the USB ON/ OFF switch to “OFF.” The image is coarse right — p This is not a malfunction. after being played back., Symptom Cause Solution The images cannot be • The [VIDEO OUT] setting for the camera in p Set [VIDEO OUT] to [NTSC] or [PAL] (pages 44, 102). played back on a TV. SET UP is incorrect. • The connection is not correct. p Check the connection (page 37). The images cannot be — p See page 89. played back on a computer. Unknown beeps are heard • These beeps are heard when the auto focus is p This is not a malfunction. Set the focus preset distance from the camera while working. (page 47). viewing a movie.

Deleting/editing an image

Symptom Cause Solution Your camera cannot • The image is protected. p Cancel the protection (page 61). delete an image. • The write-protect switch on the “Memory Stick” p Set it to the recording position (page 104). is set to the LOCK position. You have deleted the • Once you have deleted an image, you cannot p The write-protect switch on the “Memory Stick” will prevent image by mistake. restore it. you from deleting images by mistake (page 104). p Protecting the image can prevent accidental erasure (page 61). The resizing function • Movie (MPEG movie)/Clip Motion/Multi Burst — does not work. files cannot be resized. You cannot attach a print • Print (DPOF) marks cannot be attached to movie — (DPOF) mark. (MPEG movie)/Clip Motion files. You cannot cut a movie. • The movie is not long enough to cut. — • Protected movie (MPEG movie), Clip Motion, — Multi Burst files and still images cannot be cut., Troubleshooting

Computers

Symptom Cause Solution You do not know whether — p Check “Recommended computer environment” (pages 72, 82). or not your OS can be used with the camera. You cannot install the — p In Windows 2000, log on as Administrator (authorized USB driver. Administrators). Your computer does not • The camera is turned off. p Turn on the camera (page 16). recognize your camera. • The battery level is too low. p Use the AC power adaptor (supplied) (page 15). • You are not using the supplied USB cable. p Use the supplied USB cable (page 76). • The USB cable is not connected securely. p Disconnect the USB cable, and securely connect it again. Make sure that “USB MODE” is displayed on the LCD screen (page 76). • [USB CONNECT] is set to [PTP] in the SET UP p Set it to [NORMAL] (page 102). settings. • The USB ON/OFF switch on the USB cradle is p Set it to “ON” (page 76) set to “OFF.” • The camera is not properly installed to the USB p Properly install the camera (page 10). cradle. • The USB connectors on your computer are p Disconnect the USB cables except for those connected to the connected to other equipment besides the keyboard, the mouse, and the USB cradle. keyboard, the mouse, and the USB cradle. • The USB driver is not installed. p Install the USB driver (page 73). • Your computer does not properly recognize the p Delete the erroneously recognized device from your computer, device because you connected the camera and then install the USB driver (pages 73, 78). your computer with the USB cradle and the USB cable before you installed the “USB Driver” from the supplied CD-ROM. You cannot copy images. • The camera is not correctly connected to your p Connect the camera and your computer correctly (page 75). computer. • The copy procedure differs depending on your p Follow the copy procedure for your OS (pages 77, 78, 82). OS. p If you are using the “PIXELA ImageMixer for Sony” software, — click on HELP. p If you are using the “Image Transfer” software, see page 77, Symptom Cause Solution After making a USB — p Select [Launch Image Transfer automatically when your connection, “Image camera, etc., is connected.] at [Basic] setting (page 78). Transfer” does not — p Make a USB connection when the computer is turned on automatically start. (page 75). The image cannot be — p If you are using the “PIXELA ImageMixer for Sony” software, played back on a click on HELP. computer. — p Consult the computer or software manufacturer. The image and sound are • You are playing back the movie directly from p Copy the movie to the hard disk of the computer and then play affected by noise when the “Memory Stick.” the movie file back from the hard disk (pages 77, 82). you play back a movie on a computer. You cannot print an — p Check the printer settings. image. p See “Choosing images to print” (page 64), or if you are using the “PIXELA ImageMixer for Sony” software, click on HELP. The error message — p Set the display mode of your computer as follows: appears when loading the For Windows, 800 × 600 dots or more, high color (16-bit color, supplied CD-ROM. 65 000 colors) or more. For Macintosh, 800 × 600 dots or more, 32 000 colors or more. “Memory Stick” Symptom Cause Solution You cannot insert a • You are inserting it backwards. p Insert it from the right side (page 20). “Memory Stick.” You cannot record on a • The write-protect switch on the “Memory Stick” p Set it to the recording position (page 104). “Memory Stick.” is set to the LOCK position. • The “Memory Stick” is full. p Delete unnecessary images (pages 39, 68). You cannot format a • The write-protect switch on the “Memory Stick” p Set it to the recording position (page 104). “Memory Stick.” is set to the LOCK position. You have formatted a • All the data on the “Memory Stick” are erased by p We recommend that you set the “Memory Stick” write-protect “Memory Stick” by formatting. switch to the LOCK position to protect accidental erasure mistake. (page 104)., Troubleshooting

Others

Symptom Cause Solution The camera does not • You are not using an “InfoLITHIUM” battery p Use an “InfoLITHIUM” battery pack only (page 105). work, no operations can pack. be performed. • The battery level is low or zero (The p Charge the battery (page 11). indicator appears.). • The AC power adaptor is not connected p Connect it securely to the multi connector of the camera and to securely. a wall outlet (wall socket) (page 15). • The camera is not properly installed to the USB p Properly install the camera (page 10). cradle. The power is on, but the • The internal system is not working properly. p Disconnect, and then, after one minute, reconnect all power camera does not work. sources and turn on the camera. If this does not work, press the RESET button located inside the battery/“Memory Stick” cover with a pointed object, then turn the power on again. (This will clear the date and time settings, etc.) You cannot identify the — p Check the indicator (pages 108 to 110). indicator on the LCD screen. The lens gets fogged. • Condensation is occurring. p Turn off the camera, leave the camera for about an hour and then try to use it again (page 103). The camera gets hot if you — p This is not a malfunction. use it for a long time.,

Warnings and

messages The following messages appear on the LCD screen. (When using the Bluetooth function, see the Bluetooth function operating instructions.) Message Meaning/ Corrective Action NO MEMORY STICK • Insert a “Memory Stick” (page 20). SYSTEM ERROR • Turn the power off and on again (page 16). MEMORY STICK ERROR • Insert the “Memory Stick” correctly (page 20). • The “Memory Stick” is damaged, or the terminal section of the “Memory Stick” is dirty. MEMORY STICK TYPE • The inserted “Memory Stick” cannot be used with your camera (page 104).

ERROR

FORMAT ERROR • The “Memory Stick” format failed. Format the “Memory Stick” again (page 43). MEMORY STICK LOCKED • The write-protect switch on the “Memory Stick” is set to the LOCK position. Set it to the recording position (page 104). NO MEMORY SPACE • The capacity of the “Memory Stick” is insufficient. You cannot record images. Delete unnecessary images (pages 39, 68). NO FILE IN THIS FOLDER • No images have been recorded in this folder. FOLDER ERROR • A folder with the same first three digits number already exists in the “Memory Stick.” (For example: 123MSDCF and 123ABCDE) Select other folders, or create a new folder. CANNOT CREATE MORE • The folder whose first three digits of the name is “999” exists in the “Memory Stick.” You cannot create any folders.

FOLDER

CANNOT RECORD • You attempt to select the folder that is available only for viewing with your camera. Select other folders (page 56). FILE ERROR • An error occurred while playing back the image. FILE PROTECT • The image is protected against erasure. IMAGE SIZE OVER • You are playing back an image of a size that cannot be played back on your camera. CAN NOT DIVIDE • The movie is not long enough to be divided. • The file is not a movie (MPEG movie). INVALID OPERATION • You are playing back a file that was created on equipment other than your camera., Troubleshooting Message Meaning/ Corrective Action For "InfoLITHIUM" • The battery pack is not the “InfoLITHIUM” type. BATTERY ONLY • The battery level is low or zero. Charge the battery (page 11). Depending on the conditions of use or the type of battery pack, the indicator may flash even though there are still 5 to 10 minutes of remaining battery time left. • Camera shake may occur due to insufficient light. Use the flash, mount the camera on a tripod, or otherwise secure the camera in place. ROTATE THE LENS • The lens portion is falling downward. Rotate the lens portion.

PORTION

,

Self-diagnosis display

Your camera has a self-diagnosis display. This function displays the condition of the camera on the LCD screen using a combination of a letter and four numerical digits. If this occurs, check the following code chart and take the corresponding countermeasure. The last two digits (indicated by ss)will differ depending on the state of the camera. C:32:ss Self-diagnosis display Code Cause Countermeasure C:32: ss There is trouble with your Turn the power off and on again (page 16). camera’s hardware, or with the lens. C:13: ss The camera cannot read or write Re-insert the “Memory Stick” several data on the “Memory Stick.” times. An unformatted “Memory Stick” Format the “Memory Stick” (page 43). is inserted. The inserted “Memory Stick” Insert a new “Memory Stick” (page 20). cannot be used with your camera, or the data is damaged. E:61: ss A camera malfunction that you Press the RESET button (page 84) located E:91: ss cannot reverse has occurred. inside the battery/“Memory Stick” cover, E:92: ss then turn the power on again. If your camera is not still functioning well after trying the countermeasure a couple of times, the camera may be repaired. Contact your Sony dealer or local autholized Sony service facility and inform them of the 5- digit code. Example: E:61:10, Additional information Additional information E-mail Clip Motion

The number of images (Units: images) (Units: images)

that can be saved/ 16M 32M 64M 128M 16M 32M 64M 128M shooting time 8 16 32 65 NORMAL 88 178 358 7182272×1704 (14) (29) (59) (119) MOBILE 486 982 1 971 3 951 The number of images that can be saved and 8 16 32 65 NORMAL: When 10 frames are shot the shooting time are different, depending 2272 (3:2) (14) (29) (59) (119) MOBILE: When two frames are shot on the capacity of the “Memory Stick,” the 16 32 65 131 image size, and the image quality. Refer to 1600×1200 (29) (59) (119) (239) MPEG movie the following charts when you choose a 24 49 98 197 (Units: seconds) “Memory Stick.” 1280×960 (44) (89) (179) (359) 16M 32M 64M 128M 88 178 358 718 • The number of images is listed in FINE 640×480 320 (HQX) 42 87 176 354(194) (392) (788) (1 580) (STANDARD) order. 320×240 174 352 708 1 419 • The values for the number of images that VOICE 160×112 673 1 363 2 740 5 494 can be saved and the shooting time may (Units: images) vary, depending on the shooting conditions. 16M 32M 64M 128M Multi Burst (Units: images) • For normal shooting times and numbers 7 15 31 632272×1704 of images that can be saved, see page 34. (14) (28) (57) (114) 16M 32M 64M 128M 7 15 31 63 24 50 101 202 2272 (3:2) 1280×960 (14) (28) (57) (114) (46) (93) (187) (376) 15 31 62 125 1600×1200 (26) (54) (109) (219) 22 45 91 183 1280×960 (38) (78) (157) (316) 69 140 281 564 640×480 (121) (245) (492) (987),

Menu items

Menu items that can be changed differ depending on the position of the MODE dial. The LCD screen shows only the items you can operate based on the current position of the MODE dial. (When using the Bluetooth function, see the Bluetooth function operating instructions.) Factory settings are indicated with x.

When the MODE dial is set to

Item Setting Description (IMAGE SIZE) x2272×1704 / 2272 (3:2) / Selects the image size used when shooting still images (page 21). 1600×1200 / 1280×960 / 640×480 MODE (REC MODE) VOICE – Records an audio file (with a still image) in addition to the JPEG file (page 54). E-MAIL – Records a small-size (320×240) JPEG file in addition to the selected image size (page 53). xNORMAL – Records an image using the normal recording mode.

When the MODE dial is set to P or SCN

Item Setting Description SCN x / / / Selects one of the Scene selections. (When the MODE dial is set to P, this setting cannot be carried out.) (page 31) (EV) +2.0EV / +1.7EV / +1.3EV / Adjusts the exposure (page 47). +1.0EV / +0.7EV / +0.3EV / x0EV / −0.3EV / −0.7EV / −1.0EV / −1.3EV / −1.7EV / −2.0EV 9 (FOCUS) ∞ / 7.0m / 3.0m / 1.0m / 0.5m / Chooses the auto focus method (page 45), or sets the focus preset distance (page 47). CENTER AF / x MULTI AF, Additional information Item Setting Description WB (WHITE BAL) / / / / xAUTO Sets the white balance (page 49). (SPOT METER) ON / x OFF Matches the exposure to the subject you want to shoot (page 48). ISO 400 / 200 / 100 / xAUTO Selects the ISO sensitivity. When shooting under dark conditions or shooting a fast- moving subject, use a high-number setting. When recording high-quality images, use a low-number setting (When the MODE dial is set to SCN, this setting cannot be carried out.). (IMAGE SIZE) x2272×1704 / 2272 (3:2) / Selects the image size used when shooting still images (page 21). 1600×1200 / 1280×960 / 640×480 (P.QUALITY) xFINE / STANDARD Records images with fine image quality mode. / Records images in the standard image quality mode (page 33). MODE (REC MODE) VOICE – Records an audio file (with a still image) in addition to the JPEG file (page 54). E-MAIL – Records a small-size (320×240) JPEG file in addition to the selected image size (page 53). xNORMAL – Records an image using the normal recording mode. (FLASH LEVEL) HIGH – Makes the flash level higher than normal. xNORMAL – Normal setting. LOW – Makes the flash level lower than normal. PFX (P.EFFECT) SOLARIZE / B&W / SEPIA / Sets the special effects for the image (page 55). NEG.ART / xOFF (SHARPNESS) +2 / +1 / x0 / –1 / –2 Adjusts the sharpness of the image. The indicator appears (except when the setting is 0).

When the MODE dial is set to (when [MOVING IMAGE] is set to [MPEG MOVIE] in the SET UP

settings) Item Setting Description (EV) +2.0EV / +1.7EV / +1.3EV / Adjusts the exposure (page 47). +1.0EV / +0.7EV / +0.3EV / x0EV / −0.3EV / −0.7EV / −1.0EV / −1.3EV / −1.7EV / −2.0EV 9 (FOCUS) ∞ / 7.0m / 3.0m / 1.0m / 0.5m / Chooses the auto focus method (page 45), or sets the focus preset distance (page 47). CENTER AF / x MULTI AF, Item Setting Description WB (WHITE BAL) / / / / xAUTO Sets the white balance (page 49). (SPOT METER) ON / x OFF Matches the exposure to the subject you want to shoot (page 48). (IMAGE SIZE) 320 (HQX) / 320×240 / x160×112 Selects the MPEG image size when recording movies (page 66). PFX (P.EFFECT) SOLARIZE / B&W / SEPIA / Sets the special effects for the image (page 55). NEG.ART / xOFF

When the MODE dial is set to (when [MOVING IMAGE] is set to [CLIP MOTION] in the SET UP settings)

Item Setting Description (EV) +2.0EV / +1.7EV / +1.3EV / Adjusts the exposure (page 47). +1.0EV / +0.7EV / +0.3EV / x0EV / −0.3EV / −0.7EV / −1.0EV / −1.3EV / −1.7EV / −2.0EV 9 (FOCUS) ∞ / 7.0m / 3.0m / 1.0m / 0.5m / Chooses the auto focus method (page 45) or sets the focus preset distance (page 47). CENTER AF / x MULTI AF WB (WHITE BAL) / / / / xAUTO Sets the white balance (page 49). (SPOT METER) ON / x OFF Matches the exposure to the subject you want to shoot (page 48). (IMAGE SIZE) xNORMAL / MOBILE Selects the Clip Motion image size (page 51). (FLASH LEVEL) HIGH – Makes the flash level higher than normal. xNORMAL – Normal setting. LOW – Makes the flash level lower than normal. PFX (P.EFFECT) SOLARIZE / B&W / SEPIA / Sets the special effects for the image (page 55). NEG.ART / xOFF (SHARPNESS) +2 / +1/ x0 / –1 / –2 Adjusts the sharpness of the image. The indicator appears (except when the setting is 0)., Additional information

When the MODE dial is set to (when [MOVING IMAGE] is set to [MULTI BURST] in the SET UP settings)

Item Setting Description (EV) +2.0EV / +1.7EV / +1.3EV / Adjusts the exposure (page 47). +1.0EV / +0.7EV / +0.3EV / x0EV / −0.3EV / −0.7EV / −1.0EV / −1.3EV / −1.7EV / −2.0EV 9 (FOCUS) ∞ / 7.0m / 3.0m / 1.0m / 0.5m / Chooses the auto focus method (page 45) or sets the focus preset distance (page 47). CENTER AF / x MULTI AF WB (WHITE BAL) / / / / xAUTO Sets the white balance (page 49). (SPOT METER) ON / x OFF Matches the exposure to the subject you want to shoot (page 48). (INTERVAL) 1/7.5 / 1/15 / x1/30 (NTSC) – In NTSC mode, choose the Multi Burst between-frame shutter interval. 1/6.3 / 1/12.5 / x1/25 (PAL) – In PAL mode, choose the Multi Burst between-frame shutter interval. • The choices of between-frame shutter interval differ depending on the setting of the [VIDEO OUT] item in the SET UP setting (page 102). (P.QUALITY) xFINE / STANDARD Records images with fine image quality mode. / Records images in the standard image quality mode (page 33). PFX (P.EFFECT) SOLARIZE / B&W / SEPIA / Sets the special effects for the image (page 55). NEG.ART / xOFF (SHARPNESS) +2 / +1 / x0 / –1 / –2 Adjusts the sharpness of the image. The indicator appears (except when the setting is 0).,

When the MODE dial is set to

Item Setting Description FOLDER OK/CANCEL Select the folder contains the images you want to play back (page 57). DELETE OK – Deletes the displayed image (pages 39, 68). CANCEL – Cancels deleting of the image. PROTECT — Protects images against accidental erasure (page 61). DPOF — Selects still images you want to attach/cancel the print (DPOF) mark (page 64). SLIDE INTERVAL – Sets the slide show interval. (For single-image screen only.) x3 sec/ 5 sec/ 10 sec/ 30 sec/ 1 min IMAGE – Selects images from either folder or “Memory Stick.” xFOLDER/ALL REPEAT – Repeats the slide show. xON/OFF START – Starts the slide show. CANCEL – Cancels the settings and execution of the slide show. RESIZE 2272×1704 / 1600×1200 / Changes the recorded image size (page 63). (For single-image screen only.) 1280×960 / 640×480 / CANCEL ROTATE (counter-clockwise) / Rotates the still image (page 60). (For single-image screen only.) (clockwise) / OK / CANCEL DIVIDE OK / CANCEL Divides a movie (page 70). (For single-image screen only.), Additional information

SET UP items

Set the MODE dial to SET UP. The SET UP Factory settings are indicated with x. screen appears. For details on (Bluetooth SETUP), see the Bluetooth function operating instructions. (CAMERA) Item Setting Description MOVING IMAGE xMPEG MOVIE / CLIP MOTION Selects the shooting mode (pages 44, 51, 52, 66). / MULTI BURST DATE/TIME DAY & TIME / DATE / xOFF Selects whether to insert the date and time into the image (page 30). When shooting movies, or images recorded in Clip Motion/Multi Burst modes, the date and time cannot be inserted in the image. Also, the date and time will not be displayed when shooting. The date and time will be displayed when the image is played back. RED EYE REDUCTION ON / xOFF Reduces the red-eye phenomenon when using a flash (page 27). AF ILLUMINATOR xAUTO / OFF Selects whether to emit an AF assist light in the dark. Helps when it is hard to focus on the subject under dark lighting (page 28). (MEMORY STICK TOOL) Item Setting Description FORMAT OK / CANCEL Formats the “Memory Stick.” Note that formatting erases all data on a “Memory Stick,” including even protected images (page 61). CREATE REC. OK / CANCEL Creates a folder for recording images (page 56).

FOLDER

CHANGE REC. OK / CANCEL Changes a folder for recording images (page 56).

FOLDER

, (SETUP 1) Item Setting Description LCD BRIGHT/ Selects the LCD brightness. This has no effect on the recorded images. BRIGHTNESS xNORMAL/ DARK LCD BACKLIGHT BRIGHT/ Selects the brightness of the LCD backlight. Selecting [BRIGHT] makes the screen bright and easy to xNORMAL see when using the camera outdoors or in other bright locations, but also uses up the battery charge faster. Displayed only when you are using the camera with the battery pack. When [POWER SAVE] is set to [ON], this item cannot be shown. BEEP SHUTTER – Turns on the shutter sound when you press the shutter button. x ON – Turns on the beep/shutter sound when you press the control button/ press the shutter button. OFF – Turns off the beep/shutter sound. POWER SAVE x ON / OFF Selects whether to use the POWER SAVE mode (page 14). Displayed only when you are using the camera with the battery pack. (SETUP 2) Item Setting Description FILE NUMBER x SERIES – Assigns numbers to files in sequence even if the “Memory Stick” is changed or the recording folder is changed. RESET – Resets the file numbering and starts from 0001 each time the folder is changed. (When the recording folder contains a file, a number one higher than the largest number is assigned.) USB CONNECT PTP/xNORMAL Switches the USB mode (page 72). VIDEO OUT NTSC – Sets the video output signal to NTSC mode (e.g., Japan, USA). PAL – Sets the video output signal to PAL mode (e.g., Europe). LANGUAGE — Displays the menu items, warnings and messages in selected language. CLOCK SET OK / CANCEL Sets the date and time (page 18)., Additional information

On moisture condensation The internal rechargeable button Precautions If the camera is brought directly from a cold battery

to a warm location, or is placed in a very This camera has an internal rechargeable

Cleaning damp room, moisture may condense inside button battery for maintaining the date and

Cleaning the LCD screen or outside the camera. This moisture time and other settings regardless of Clean the screen surface with an LCD condensation may cause a malfunction of whether the power is on or off. cleaning kit (not supplied) to remove the camera. This rechargeable button battery is fingerprints, dust, etc. continually charged as long as you are using Moisture condensation occurs easily the camera. However, if you use the camera Cleaning the lens when: for only short periods it discharges Wipe the lens with a soft cloth to remove • The camera is brought from a cold gradually, and if you do not use the camera fingerprints, dust, etc. location such as a ski slope into a warmly at all for about one month it becomes heated room. completely discharged. In this case, be sure Cleaning the camera surface • The camera is taken from an air- to charge this rechargeable button battery Clean the camera surface with a soft cloth conditioned room or car interior to the hot before using the camera. slightly moistened with water, then wipe the outdoors, etc. Note that even if this rechargeable button surface with a dry cloth. Do not use any type battery is not charged, you can still use the of solvent such as thinner, alcohol or benzine To prevent moisture condensation camera as long as you do not record the date as this may damage the finish or the casing. When bringing the camera from a cold and time. place to a warm place, seal the camera in a

Note on operating temperature plastic bag and leave it in the new location How to charge

for about an hour. Remove the plastic bag The camera is designed for use within a Connect the camera to a wall outlet (wall temperature range of 0° to 40° (32°F to when the camera has adapted to the new socket) using the AC power adaptor and temperature. 104°F). Shooting in extremely cold or hot USB cradle, or install a charged battery locations that exceed this range is not pack, and leave the camera for 24 hours or recommended. If moisture condensation occurs more with the power turned off. Turn off the camera and wait about an hour for the moisture to evaporate. Note that if The internal rechargeable button battery is you attempt to shoot with moisture installed under the cover (by the side of the remaining inside the lens, you will be speaker) located at the bottom of the unable to record clear images. camera. Do not remove it except when disposing of the camera., may differ depending on the “Memory Stick” Notes on using the “Memory Stick

The “Memory Stick” you use. Duo” (optional)

Connector • Be sure to insert the “Memory Stick Duo” into “Memory Stick” is a new compact, portable the “Memory Stick Duo” adaptor when using and versatile IC recording medium with a the “Memory Stick Duo” with the camera. data capacity that exceeds the capacity of a • Verify that the insert direction of the “Memory Stick Duo.” The use of wrong direction may floppy disk. Write-protect cause a malfunction. You can use the “Memory Stick” as an switch • Do not insert the “Memory Stick Duo” not external recording media that can be inserted into the “Memory Stick Duo” adaptor attached or removed as well as exchanging Labeling position into the “Memory Stick”-compatible unit. This data between the units. may cause a malfunction of the unit.• Do not remove the “Memory Stick” or turn off the camera while reading or writing data. There are two types of “Memory Stick”: an • Data may be damaged in a location subject to ordinary “Memory Stick” and a the effects of static electricity or noise. “MagicGate Memory Stick” that are • We recommend you back up the important data. • Do not attach any other material than the equipped with the MagicGate copyright supplied label on the labeling position. protection technology. You can use both • When you carry or store the “Memory Stick,” types of “Memory Stick” with your camera. put it in the case supplied with it. However, because your camera does not • Do not touch the terminals of a “Memory support the MagicGate standards, data Stick” with your hand or a metal object. recorded with your camera is not subject to • Do not strike, bend or drop a “Memory Stick.” • Do not disassemble or modify a “Memory MagicGate* copyright protection. Stick.” You can also use the “Memory Stick Duo” • Do not expose the “Memory Stick” to water. with the camera. • Avoid using or storing the “Memory Stick” at the following places: * MagicGate is copyright protection technology – In a car parked in the sun, or at a high that uses encryption technology. temperature. – Under direct sunlight, – At a humid place or near a corrosive material. Notes on use When using the supplied “Memory Stick”: • You cannot record or delete images when the write-protect switch is set to LOCK. The position or the shape of the write-protect switch, Additional information

Effective use of the battery pack How to store the battery pack The “InfoLITHIUM” • Battery performance decreases in low- • If the battery pack is not to be used for a

battery pack temperature surroundings, and the battery long time, do the following procedure life is shortened under such once per year to maintain proper function. circumstances. To use the battery pack 1. Fully charge the battery. longer, we recommend you keep the 2. Discharge on your camera. battery pack in a pocket close to your 3. Remove the battery from your camera

What is the “InfoLITHIUM”

body to warm it, and insert it in your and store it in a dry, cool place. battery pack? camera just before you start shooting. • To use the battery pack up on your The “InfoLITHIUM” battery pack is a • If you use the LCD screen or shoot a lot camera, leave the POWER button to on in lithium-ion battery pack that has functions using the flash, the battery power will be slide show playback mode (page 59) until for communicating information related to used up faster. the power goes off. operating conditions of your camera. • We recommend having spare batteries The “InfoLITHIUM” battery pack handy for two or three times the expected Battery life calculates the power consumption shooting time, and try test shooting according to the operating conditions of • The battery life is limited. Battery before actually using the camera. your camera, and displays the remaining capacity decreases little by little as you • Do not expose the battery pack to water. battery time in minutes. use it more and more, and as time passes. The battery pack is not water-resistant. When the battery operating time seems to have been considerably shortened, a

Charging the battery pack Remaining battery time indicator probable cause is that the battery pack has

• We recommend charging the battery pack If the power goes off although the battery reached the end of its life. in an ambient temperature of between remaining indicator indicates that the • The battery life varies depending on 10°C to 30°C (50°F to 86°F). If you battery pack has enough power to operate, storage, operating conditions, and charge the battery pack outside of this charge the battery pack fully again after environment, and is different for each temperature range, you may not be able to running it down so that the indication on the battery pack. efficiently charge the battery pack. battery remaining indicator is correct. Note, however, that the correct battery indication sometimes will not be restored if it is used in high temperatures for a long time or left in a fully charged state, or the battery pack is frequently used.,

Input/output connectors UC-FA USB cradle Specifications Multi connector Input/output connectors

A/V OUT (MONO) jack (Monaural) For details on Bluetooth function specifications, see LCD screen Minijack the Bluetooth function operating instructions Video: 1 Vp-p, 75 Ω, unbalanced, LCD panel used sync negative 3.8 cm (1.5 type) TFT drive

System Audio: 327 mV (at a 47 kΩ load)

Total number of dots Output impedance 2.2 kΩ Image device 8.98 mm (1/1.8 type) color 123 200 (560×220) dots CCD USB jack mini-B Primary color filter DC IN connectorPower, general Total pixels number of camera Camera connector Approx. 4 130 000 pixels Used battery pack Effective pixels number of camera NP-FC10 AC-LM5 AC power adaptor Approx. 3 950 000 pixels Power requirements 3.6 V Power requirementsLens f=7.65 mm AC 100 to 240 V, 50/60 Hz (35 mm camera conversion: 37mm Power consumption (when shooting) 15 1.9 W Rated output voltage(1 /32 inches)) DC 4.2 V, 1.5 A F2.8 Operating temperature range 0° to +40°C (32° to +104°F) Operating temperature range Exposure control 0° to +40°C (32° to +104°F) Automatic, Storage temperature range Scene selection (four modes) −20° to +60°C (−4° to +140°F) Storage temperature range −20° to +60°C (−4° to +140°F) White balance Dimensions 98.1 × 71 × 27 mm771Dimensions 47 × 30 × 80 mm (1 7/ × 1 3/ × Automatic, Daylight, Cloudy, (3 /8 × 2 /8 × 1 /8 inches) 8 16 3 1/ inches) (W/H/D, protruding Fluorescent, Incandescent (W/H/D, protruding portions not 4parts not included) File format (DCF compliant) included) Mass Approx. 170 g (6.0 oz) Still images: Exif Ver. 2.2, JPEG Mass Approx. 185 g (6.5 oz) (NP-FC10 (adaptor only) compliant, GIF (for Clip Motion), battery pack, “Memory Stick” and DPOF compatible wrist strap included) Audio with still image: MPEG1 NP-FC10 battery packMicrophone Electret condenser microphone compliant (Monaural) Used battery Lithium ion battery Movies: MPEG1 compliant Speaker Dynamic speaker Maximum voltage (Monaural) DC 4.2 V Recording media Nominal voltage “Memory Stick” DC 3.6 V Flash Recommended distance Capacity 2.4 Wh (675 mAh) 0.5 to 1.7 m (1 feet 7 3/4 inches to 5 feet 7 inches) (when ISO sensitivity is set to Auto), Additional information

Accessories

• NP-FC10 battery pack (1) • AC-LM5 AC power adaptor (1) • UC-FA USB cradle • USB cable (1) • A/V connecting cable (1) • Power cord (mains lead) (1) • Wrist strap (1) • “Memory Stick” (16MB) (1) • CD-ROM (USB driver: SPVD-008) (1) • Operating Instructions (1) • Bluetooth Function Operating Instructions (1) Design and specifications are subject to change without notice., F Scene selection indicator (31)

The LCD screen G Date/time indicator (30)

ISO sensitivity (97) When using the Bluetooth function, see the H Sharpness indicator (97, 98, 99) Bluetooth function operating instructions. I Picture effect indicator (55)

For shooting still images J Low battery warning (93)

K AF range finder (45) L Spot light-meter aiming point 1 qd (49) 2 M Image quality indicator (33, 34)qf N Recording folder indicator (55) qg O Remaining number of recordable qh images indicator (34) 5 60min 640 101 3:2 Self-diagnosis display (94)qj6PRemaining “Memory Stick” 7 SOLARIZE qkF2.8 capacity indicator (34) + 125 ql8 Q Center AF /Multi AF w; indicator (45)/Focus preset value (47) wa WB ISO R EV adjustment indicator (47) q; ws S Iris value indicator qa wd T Shutter speed indicator qs wf U Macro (25) V Self-timer indicator (26) W Vibration warning indicator (93) A Image size indicator (21, 34) E Flash mode (27)/Red-eye X Menu/Guide menu (44) B Recording mode indicator reduction (27)/White balance • Pressing the MENU button switches the menu/ (51–54) indicator (49)/AF illuminator guide menu on/off. C AE/AF lock indicator (22, 46) indicator (28, 101)/Program mode D Battery remaining indicator (13) indicator (45), Additional information

For shooting movies

60min 160 101 3 STBY 00:00:00 [00:28:25] q; 4 SOLARIZE qa 5 + qs qd qf WB qg A Recording mode indicator (66) K Center AF /Multi AF The page numbers in parentheses indicate B Battery remaining indicator (13) indicator (45)/Focus preset value the location of additional important C White balance indicator (49) (47) information. D Picture effect indicator (55) L EV adjustment indicator (47) E Spot light-metering aiming point M Macro (25) (49) N Self-timer indicator (26) F AF range finder (45) O Menu/Guide menu (44) G Image size indicator (66) • Pressing the MENU button switches the menu/ H Recording time (Maximum guide menu on/off. recordable time) indicator (95)/ Self-diagnosis display (94) I Recording folder indicator (55) J Remaining “Memory Stick” capacity indicator (95),

For still image playback For movie playback X Menu/Guide menu (44)

1 6 qh The page numbers in parentheses indicate qj27qd the location of additional important qk 60min 640 101 information. 3 101 12/12 8 qf ql 9 60min 160 4 x1.3 w; qg 101 8/8 00:00:12 q; wa qa ws BACK/NEXT VOLUME qs wd A Change folder indicator (57) FOLDER DELETE PROTECT DPOF wf

OK

B Recording mode indicator (53) C Volume indicator (54)/Protect M Image size indicator (67) mark indicator (61)/Print (DPOF) N Recording mode indicator (67) mark indicator (64) O Playback indicator (67)/Volume D Zoom indicator (58) indicator (67) E Folder-file number (81) P Change folder indicator (57) F Playback folder indicator (57) Q Playback folder indicator (57) G Recording folder indicator (55) R Image number/Number of H Remaining “Memory Stick” images recorded in the playback capacity indicator (34) folder (67) I Number of images recorded in S Recording folder indicator (56) the playback folder (34) T Remaining “Memory Stick” J Image number (34) capacity indicator (95) K Image size indicator (21, 34) U Counter (67) L Recording date/time of the V Playback screen (67) image (30)/Menu/Guide menu W Playback bar (67) (44),

Additional information

Additional information Computer Focus preset ... 47

Index Copying images to your computer ... 72, 82 Shooting (using auto mode) ... 22

USB cable ... 76 Folder

Symbols USB driver ... 73, 82 Folder for playback ... 57

Control button ... 17 Recording folder ... 56 “InfoLITHIUM” battery pack ...11, 105 Creating a new folder ... 56 FORMAT ... 43

A D G

A/V connecting cable ...37 DC plug ... 10 GIF ... 81 Access lamp ...20 Deleting images ... 39 AE/AF lock ...22, 46 DIVIDE ... 70 AE/AF lock lamp ...9 I AF ILLUMINATOR ...101 Image AF illuminator ...8, 28 E Copying images to your computer ... 72, 82 AF lock ...22, 46 Editing still images File names ... 81 AF lock lamp (green) ...9 Print (DPOF) mark ... 64 Image file storage destinations ... 80 Auto focus mode ...23, 45 Protect ... 61 Image quality ... 33, 34 Auto Power Off feature ...16 Resize ... 63 Image size ... 21, 34, 95 E-MAIL ... 53 Image Transfer ... 73, 77, 83

B EV adjustment ... 47 ImageMixer ... 75, 83

Exposure Index screen ... 35 Battery pack EV adjustment ... 47 Installation ... 73, 82 Battery life ...13 ISO ... 97 Charging the battery pack ...11 Charging time ...13 F Remaining indicator ...13 File J Beep/shutter sound ...102 File names ... 81 JPG ... 81 Image file storage destinations ... 80

C Finder ... 29 L

Flash Camera connector ...10 LCD screen display FLASH LEVEL ... 50, 97, 98 Changing the recording folder ...56 DSPL/LCD ON/OFF ... 29 RED EYE REDUCTION ... 27 Charging LCD brightness ... 102 Selecting a flash mode ... 27 Charging the battery pack ...11 Focus Charging time ...13 AE/AF lock lamp ... 9 Cleaning ...103 AF lock ... 22, 46 1,

M R Viewing the images on your computer

Memory Stick RED EYE REDUCTION ... 27, 101 ... 79, 83 Formatting a “Memory Stick” ... 43 RESET button ... 9, 84 Still image shooting Inserting a “Memory Stick” ... 20 AE/AF lock lamp ... 9 Number of shooting images ... 34 S Auto focus mode ... 23, 45 The number of images that can be saved/ EV adjustment ... 47Scene selection ... 31 shooting time ... 95 Image size ... 21, 34, 95SCN ... 32 Menu Number of shooting images ... 34Self-diagnosis display ... 94 Changing menu ... 44 Picture effect ... 55Self-timer ... 26 MODE dial ... 9 Scene selection ... 31Setting Moisture condensation ... 103 Selecting a flash mode ... 27Changing menu ... 44 Movie Shooting close-ups (Macro) ... 25Date and time ... 18 Continuous shooting ... 14 Shooting with the date and time inserted Image size ... 21, 34, 95 Cutting movies ... 70 ... 30SET UP ... 44 Deleting movies ... 68 Smart zoom ... 24Setting the date and time ... 18 Shooting movies ... 66 Spot light-metering ... 48SHARPNESS ... 97, 98, 99 Viewing ... 67 The number of images that can be saved/Shooting close-ups (Macro) ... 25 MPG ... 81 shooting time ... 14, 34, 95Shooting mode Multi connector ... 9 Using auto mode ... 22Clip Motion ... 51 Using the self-timer ... 26 E-MAIL ... 53

N White balance ... 49MPEG MOVIE ... 66

NR slow shutter ... 33 Shooting (using auto mode) ... 22 NTSC ... 102 Shooting in Multi Burst mode ... 52 T VOICE ... 54 Trimming ... 59

P Shooting with the date and time inserted ... 30

PAL ... 102 Still image playback U Picture effect ... 55 Index (nine-image) screen ... 35 USB Power Playback zoom ... 58 Cancel the USB connection ... 77, 83 An external power source ... 15 Quick Review ... 23 Installing the USB driver ... 73, 82 Battery pack ... 11, 105 ROTATE ... 60 USB connection ... 75, 76, 82 Inserting battery pack ... 11 Slide show ... 59 USB cradle ... 10 ON/OFF ... 16 Viewing images on a TV screen ... 37 How to install/remove your camera ... 10 Precautions ... 103 Viewing on the single-image screen ... 35 USB ON/OFF switch ... 10 Using your camera abroad ... 15, Additional information

V

Viewing on the single-image screen ...35 VOICE ...54

W

Warnings and messages ...92

Z

Zoom Playback zoom ...58 Using the smart zoom ...24, Printed on 100% recycled paper using VOC (Volatile Organic Additional information on this product and answers to frequent Compound)-free vegetable oil asked questions can be found at our Customer Support Website. based ink. Sony Corporation Printed in Japan307840911, 3-079-664-11(1) Getting started _

Digital Still Camera Sending images _

Receiving images _

Bluetooth Function Operating Instructions

Before operating the unit, please read this manual thoroughly, and Using your camera as the remote camera _ retain it for future reference.

Owner’s Record Printing images_

The model and serial numbers are located on the bottom. Record the serial number in the space provided below. Refer to these numbers Authentication/Deleting the record_ whenever you call upon your Sony dealer regarding this product. Model No. DSC-FX77 Additional information _ Serial No. Index _

DSC-FX77

© 2002 Sony Corporation See also the operating instructions.,

Introduction

This camera is designed to connect with a device equipped with the Bluetooth function, such as a digital still camera, a computer, or a printer. You can send/ receive images without a cable. You can use your camera as a remote camera of your computer to perform remote shooting from the computer. Printing images with a printer (page 16) • Sending/receiving images with a Sending/receiving Sony VAIO (pages 10, 13) images with another • Using your camera as a remote digital still camera camera (page 14) (pages 8, 12) To connect with your digital still camera, the Bluetooth device must be compatible with the “Image Push Feature” or the “Remote Camera Feature” of the “Basic Imaging Profile” (BIP). For details, see 2 page 4., Preparing the VAIO... 15

Table of contents Printing images Getting started Printing images ... 16

Sending images to a printer ... 16 Introduction ...2 The Bluetooth wireless technology...4 Authentication/Deleting the The “Basic Imaging Profile”...4 Bluetooth operation...4 record Naming your camera ...5 Authentication... 17 Entering the passkey... 17

Sending images Deleting the record ... 18

Discovering devices (New search)... 7 Sending images to a camera...8 Additional information On the single screen ...8 File types that can be sent/received ... 19 On the Index (nine-image) screen...9 Sending ... 19 On the Index (triple-image) screen ...10 Receiving... 19 Sending images to a Sony VAIO ...10 Troubleshooting... 20 Warnings and messages... 29

Receiving images Menu items ... 31

SET UP items ... 32 Receiving images from a camera ...12 Bluetooth specifications... 33 Receiving images from a Sony VAIO ...13 The LCD screen... 34 Preparing your camera ...13 Preparing the VAIO ...13

Index Using your camera as the Index ... 36

remote camera Using your camera as the remote camera of a Sony VAIO ...14 Preparing your camera ...14,

Getting started The “Basic Imaging Profile” The Bluetooth Bluetooth operation

wireless technology The “Basic Imaging Profile” (BIP) is the specification used when sending or Pressing the Bluetooth button opens the receiving images between Bluetooth The Bluetooth wireless technology allows Bluetooth menu. The Bluetooth lamp devices. The main features of the BIP communication between various Bluetooth turns blue during Bluetooth operations. devices without using cables. Devices enable sending or receiving images, use of the remote shutter feature of a digital still Antenna which can use this technology include PCs, portion camera. computer peripheral devices, PDAs, and mobile phones. This omnidirectional To connect with your camera, the Bluetooth Bluetooth device must be compatible with the “Image lamp communication system enables Push Feature” or the “Remote Camera Bluetooth communication even if the Bluetooth button device is in a bag or if there are obstacles Feature” of the “Basic Imaging Profile” (BIP). between the devices. Before using the Bluetooth device, check Also, the Bluetooth wireless technology has advanced security functions, such as the BIP specifications of the device. scrambled frequencies and data encryption. • When using the Bluetooth function, the • Do not cover the antenna portion during a distance between the camera and the device you Bluetooth connection. intend to connect must be within 10 m (3.3 feet) • Removing the battery pack during a Bluetooth without obstacles. connection may cause a malfunction. • When using the Bluetooth function, actual remaining time and time indicated with the battery remaining indicator may be different., Getting started a Set the MODE dial to SET UP. d Select the desired character

Naming your camera with v/V/b/B, then press z.

b Select (Bluetooth SETUP)

MODE dial: SET UP with , select [CHANGE The selected character is entered.V

You can name your camera with a name NAME] with V/B, select [OK] INPUT DEVICE NAME a containing up to 24 characters. This name is with v/B, then press z. 56789OKused when the camera is searched for and The following screen appears. abcdeBACK SPACE discovered by other Bluetooth devices. fghijDELETE ALL “SONY Cyber-shot” is the default name. INPUT DEVICE NAME EXITMENU SONY Cyber–shot OK CHARACTER SELECT We recommend you rename your camera } ~ O K with an easy-to-understand name. 01234BACK SPACE e Repeat Step 4 as many times56789DELETE ALL Control button EXIT as needed to name the OK MENU CHARACTER SELECT camera. MODE dial c When renaming the camera for f Select [OK] with v/B, then

MENU

the first time, select [DELETE press z.

ALL] with v/V/B, then press z. Renaming is completed and the

The default name is deleted. (Bluetooth SETUP) screen appears again. Confirm the name on the screen. INPUT DEVICE NAME Bluetooth SETUP } ~ O K SECURITY LEVEL : LOW01234BACK SPACE EDIT RECORD : 0 CHANGE NAME : 56789DELETE ALL dsc Name 00:0C:3E:3A:4B:69

EXIT

OK MENU CHARACTER SELECT Device • Be sure to enter one or more characters when PAGE SELECT address naming your camera. • Identify the camera with a name and device address so that it can be located during a device discovery.,

To change the character type

Each time you press the MENU button, the character type changes as follows: number t lowercase letters t uppercase letters t symbols

To delete one character

Select [BACK SPACE], then press z. The last character is deleted. Only the last charater in a series can be deleted using [BACK SPACE].

To delete all the characters

Select [DELETE ALL], then press z. All the characters are deleted.

To cancel the renaming

operation Select [EXIT], then press z. The previous name is not changed.,

Sending images

Sending images a Set the MODE dial to and

Discovering devices display the image you want to 60min

send. 1 UNIT(S) FOUND– New search SEARCHING Bluetooth DEVICE

MODE dial: b Press Bluetooth.

You have to discover a Bluetooth device The Bluetooth menu appears.

STOP OK

when the camera has not been connected to The device discovery operation is the device previously or when the camera 60min 2272 completed, the SELECT THE 101 1/1 does not have information on the device in RECEIVER screen appears again. the record for the connected device. SELECT THE RECEIVER 1/1

Before operation SEND RECEIVE PRINT NAME :OK [SONY Cyber–shotX]

ADDRESS : Be sure to set the Bluetooth device to allow TYPE : CAMERASUPPORTED : UNKNOWN it to be connected. c Select [SEND] with b, then SEARCH : NEW CONNECT press . EXITz NEW SEARCH

OK

MODE dial The Bluetooth function starts up and Bluetooth the SELECT THE RECEIVER screen appears. To cancel the new search Select [STOP], then press z in Step 4. The devices discovered up to the point you SELECT THE RECEIVER stop the discovery operation are added to NO RECORD FOR CONNECTED DEVICE TRY A NEW SEARCH the SELECT THE RECEIVER screen.

CONNECT EXIT

NEW SEARCH • You may not be able to discover the desired OK device if the setting of the device is not discoverable. If you cannot discover the desired d Select [NEW SEARCH] with V, device by repeating a new search, check the then press z. setting of the device. Control button • The maximum number of devices that can be “SEARCHING Bluetooth DEVICE” is discoverable during a new search is 10 devices. indicated and the number of Bluetooth • The result of new search is displayed along devices discovered is indicated. with the record.,

On the single screen Sending images to a 60min

SONY Cyber–shotX camera a Set the MODE dial to and display the image you want to

SENDING MODE dial: send.

You can send images to a camera equipped EXITb Press Bluetooth. OK with the BIP-compatible Bluetooth The Bluetooth menu appears. function. 60min 101SONY Cyber–shot 00:0C:3E:3A:4B:69

Before operation 60min 2272 101 1/1 0/0 RECEIVING

Be sure to set the receiving camera to enable it to receive images (page 12). EXIT

OK

MODE dial SEND RECEIVE PRINTOK • If passkey entry is required on the sending and receiving cameras, enter the passkey Bluetooth c Select [SEND] with b, then (page 17). • If you run past the time limit for the press z. passkey entry (30 seconds), connect again. The Bluetooth function starts up and the SELECT THE RECEIVER screen f To send other images, display appears. the desired image with b/B, d Display the record of the then press z. receiving camera with b/B or perform a new search (page 7). To cancel the sending operation SMART ZOOM Sending camera e Select [CONNECT] with v, then Select [EXIT], then press z in Step 5 or Control button press z. 6. The Bluetooth function is turned off “SENDING” is indicated and the and the Bluetooth menu appears again. selected image is sent to the receiving • This explanation is given using the DSC-FX77 camera. model. • For the image types you can send, see page 19., Sending images

On the Index (nine-image)

screen 60min SONY Cyber–shotX a Set the MODE dial to , then 0/1

SENDING

press the SMART ZOOM W button once to switch to the EXIT SELECT MOVE Bluetooth TO NEXT OK

Index (nine-image) screen. At this time, the image has not been

b Press Bluetooth. sent. 60min 101SONY Cyber–shot 00:0C:3E:3A:4B:69 The Bluetooth menu appears. f To send other images at the 0/0 same time, repeat Step 5. RECEIVING • The maximum number of images you can

EXIT

send at a time is 54. OK g Press Bluetooth. • If passkey entry is required on the sending and receiving cameras, enter the passkey h Select [OK] with , then press (page 17).B SEND RECEIVE PRINT • If you run past the time limit for the z. passkey entry (30 seconds), connect again. c Select [SEND] with b, then The Bluetooth function starts up and press z. the SELECT THE RECEIVER screen When the images have been sent, appears. “SENT” is indicated on the sending d Select [SELECT] with B, then camera. press . i Display the record of the z receiving camera with b/B or k Select [EXIT], then press z. e Select the image you want to perform a new search (page 7). The Bluetooth function turns off and send with v/V/b/B, then press the Bluetooth menu appears again.j Select [CONNECT] with v, thenzAmark is attached on the selected press z. To cancel the sending operation image. “SENDING” is indicated and the Sending camera selected image is sent to the receiving Select [EXIT], then press z in Step 0. camera. The Bluetooth function is turned off and the Bluetooth menu appears again.,

On the Index (triple-image) “SENDING” is indicated and the

screen selected image is sent to the receiver Sending images to a camera. Sony VAIO a Set the MODE dial to , then press the SMART ZOOM W 60min MODE dial: SONY Cyber–shotX button twice to switch to the You can send images to a VAIO equipped

Index (triple-image) screen.

SENDING with the BIP-compatible Bluetooth function. b Move the image you want to EXIT

OK

send to the center with b/B. MODE dial c Press Bluetooth. Bluetooth60min 101 SONY Cyber–shot The Bluetooth menu appears. 00:0C:3E:3A:4B:69 0/0RECEIVING

EXIT OK

• If passkey entry is required on the sending

PRINT

RECEIVE and receiving cameras, enter the passkey

SEND

101-0012 20037410:30 (page 17).AM OK BACK/NEXT • If you run past the time limit for the passkey entry (30 seconds), connect again. d Select [SEND] with V, then press z. g To send other images, move Control button The Bluetooth function starts up and the desired image to the center the SELECT THE RECEIVER screen with b/B, then press z. • For the latest information about appears. connection using a VAIO, see the

To cancel the sending operation following URL: http://www.sony-e Display the record of the imaging.com/support/

receiving camera with b/B or Sending Camera • You can also operate with the index (nine- or perform a new search (page 7). Select [EXIT], then press z in Step 6 or triple-image) screen. 7. The Bluetooth function is turned off • For the image types you can send, see page 19. f Select [CONNECT] with v, then and the Bluetooth menu appears again. press z., Sending images a Turn on your VAIO and turn on the Bluetooth function. 60min

VAIO

b Start up “BlueSpace.”

SENDING

For details on this operation, refer to the HELP of the VAIO. EXIT

OK

c Set the MODE dial on the • If passkey entry is required on your camera to and display the camera and the VAIO, enter the passkey image you want to send. (page 17).• If you run past the time limit for the d Press Bluetooth on the passkey entry (30 seconds), connect again. camera. h To send other images, display The Bluetooth menu appears. the desired image with b/B, Select [SEND] with , then then press z.e b press z.

To cancel the sending operation

The Bluetooth function starts up and the SELECT THE RECEIVER screen Your camera appears. Select [EXIT], then press z in Step 7 or 8. The Bluetooth function is turned off f Display the record of the and the Bluetooth menu appears again. receiver with b/B or perform new search (page 7). g Select [CONNECT] with v, then press z. “SENDING” is indicated on the camera and the selected image is sent to the VAIO.,

Receiving images

b Press Bluetooth.

Receiving images The Bluetooth menu appears. 60min 101

SONY Cyber–shotX from a camera 1/1 60min 2272 WAITING TO RECEIVE

MODE dial: 101 1/1

You can receive images from a camera EXITOK equipped with the BIP-compatible Bluetooth function. SEND RECEIVE PRINT OK To cancel the receiving MODE dial operationc Select [RECEIVE] with b/B, When [EXIT] is indicated on the screen, Bluetooth then press z. you can cancel the receiving operation at The Bluetooth function starts up and any time. Select [EXIT], then press z. The “WAITING FOR CONNECTION” is Bluetooth function is turned off and the indicated. The camera is then Bluetooth menu appears again. The file connectable. currently being received is not saved. 60min 101 When the sending camera turns off the Bluetooth function 0/0 WAITING FOR CONNECTION The following screen appears.

EXIT OK

Control button 60min d Discover the receiving camera • You can also perform this operation with the 1/1RECEIVED index (nine- or triple-image) screen. with the sending camera, and • For the image types you can receive, see send images. EXIT

OK

page 19. “RECEIVING” is indicated and the If you want to receive other images, select image is sent to the receiving camera. [EXIT] to turn off the Bluetooth function. a Set the MODE dial to . After recording the image in the receiving camera, the receiving camera Then, repeat Steps 3 and 4. turns back to be receivable (WAITING TO RECEIVE)., Receiving images Preparing your camera Preparing the VAIO

Receiving images

from a Sony VAIO a Set the MODE dial to . a Turn on the VAIO and turn on

Press Bluetooth. the Bluetooth function.b MODE dial: The Bluetooth menu appears. b Start up “BlueSpace.”

You can receive images from a VAIO For details on the following eqquiped with the BIP-compatible 60min operations, refer to the HELP of the 2272 Bluetooth function. 101 1/1 VAIO or URL: http://www.sony- imaging.com/support/ MODE dial Bluetooth SEND RECEIVE PRINT

OK

c Select [RECEIVE] with b/B, then press z. The Bluetooth function starts up and “WAITING FOR CONNECTION” is indicated. The camera is then connectable. 60min 101 Control button 0/0 WAITING FOR CONNECTION • For the latest information about connection using a VAIO, see the EXITOK following URL: http://www.sony- imaging.com/support/ • For the image types you can receive, see page 19.,

Using your camera as the remote camera Preparing your camera Using your camera as MODE dial

the remote camera of Bluetooth a Set the MODE dial on the camera to , P, or SCN. a Sony VAIO b Press Bluetooth.

MODE dial: / P/SCN The Bluetooth menu appears.

You can perform remote shooting from a VAIO equipped with the BIP-compatible 60min 2272 101 Bluetooth function. The maximum time you can use the camera as a remote camera is REMOTE CAMERA three hours. The camera OK automatically turns off after three Control button hours. c Press z to execute [REMOTE Do not use the camera for hours as • For the latest information about CAMERA]. a surveillance camera and such. connection using a VAIO, see the The Bluetooth function starts up and This may cause a malfunction. following URL: http://www.sony- “WAITING FOR CONNECTION” is imaging.com/support/ indicated. The camera is then • When [SECURITY LEVEL] of your camera is connectable. set to [HIGH], passkey entry may be required (page 17). 60min 101 0/0 WAITING FOR CONNECTION

EXIT OK

• When [MODE] (REC MODE) is set to [VOICE], you cannot select [REMOTE CAMERA]. • You cannot use the self-timer function., Using your camera as the remote camera

Preparing the VAIO

a Turn on the VAIO and turn on the Bluetooth function. b Start up “BlueSpace.” For details on the following operations, refer to the HELP of the VAIO or URL: http:www.sony- imaging.com/support/,

Printing images Sending images to a printer • If passkey entry is required, enter the same Printing images passkey as that of the printer (page 17).

a Set the MODE dial on the • If you run past the time limit for the

MODE dial: camera to and display the passkey entry (30 seconds), connect again.

• The printer may have a predetermined You can send images to a printer equipped image you want to print. passkey or its passkey may have been set with the BIP-compatible Bluetooth function beforehand. For details on the passkey and print images. b Press Bluetooth. setting of the printer, refer to the operating The Bluetooth menu appears. instructions supplied with the printer.

Before operation 60min 2272 101 1/1 f To send other images, display

Turn on the printer, and be sure to set the the image you want to print printer to allow it to be connected. with b/B, then press z. MODE dial • The number of images you can send in a SEND RECEIVE PRINT OK row depends on the printer. Bluetooth c Select [PRINT], then press z.

To cancel the sending operation

The Bluetooth function starts up and Select [EXIT], then press z in Step 5 or the SELECT THE PRINTER screen appears. 6. The Bluetooth function is turned off and the Bluetooth menu appears again. d Display the record of the • The camera cannot cancel the printing printer with b/B or perform a operation after the image has been sent to the printer. For details to stop the printing, refer to new search (page 7). the operating instructions supplied with the printer. e Select [CONNECT] with v, then press z. Control button • The edges of the image may not be printed “PRINTING” is indicated on the depending on the printer setting. camera and the selected image is sent • It may take a lot of time to print images, • You can also perform this operation with the to the printer. depending on the image size or the printer.index (nine- or triple-image) screen. • For the image types you can send, see page 19. 60min Printer

PRINTING EXIT OK

,

Authentication/Deleting the record

Authentication/Deleting the record

When the passkey entry screen Entering the passkey Authentication appears on your camera before it

appears on the other device Enter the passkey when the passkey entry screen appears.

What’s a passkey Enter the desired passkey on your camera.

Passkey is used to authenticate two Then, enter the same passkey on the other a Select the desired character Bluetooth devices that have not previously device. with v/V/b/B, then press z. connected to each other and create a trusted The selected character is entered. relationship between them. When the passkey entry screen INPUT THE PASSKEY WITHIN 30 SECS. You need to enter the same characters appears on the other device (passkey) to each device on passkey before it appears on your camera } ~ O K authentication process. Enter the desired passkey on the other01234BACK SPACE56789DELETE ALL Once authentication of the device has been device. Then, enter the same passkey on

EXIT

confirmed, the camera registered the device your camera. OK MENU CHARACTER SELECT as a record. Since then you can connect the device without entering a passkey. When the passkey entry screen b Repeat Step 1 as many times appears on your camera and the as needed to enter the desired • To ensure proper security, the passkey other device at the same time passkey. entry has a time limit (30 seconds), based on the Bluetooth standards. You can enter the passkey on either one. c Select [OK] with v/B, then • The passkey entry may be required when the Enter the same passkey on your camera and authentication valid period of the camera on the other device. press z. other device is expired, the record is deleted, or The passkey entry is completed. the security setting is changed. • Passkey entry may be required, depending on • You can enter a passkey with up to 16 devices, each time you intend to connect. characters, however, you have to enter the • This “Passkey” is also referred to as a passkey within the time limit (30 seconds). Due “Bluetooth passkey” etc. “PIN” is also used to the time limit, we recommend you use about with the same meaning. a four-character passkey. • The character types and the number of characters available depend on the device.,

To change the character type The SELECT RECORD screen

Each time you press the MENU button, the Deleting the record appears. character type changes as follows: number SELECT RECORD 1/1 t lowercase letters t uppercase letters Your camera stores access history and NAME :SONY Cyber–shotX symbols information about the devices once ADDRESS :t TYPE : CAMERA connected as an item called the record.

To delete one character Since you can select a desired device from DELETEEXIT

the record, you do not have to perform a OK BACK/NEXT Select [BACK SPACE], then press z. The new search each time you connect. The last character is deleted. Only the last camera can store records on up to seven c Display the record you want to character in a series can be deleted using devices, and when you try to store another [BACK SPACE]. delete with b/B.record on a device, the oldest item is automatically deleted from the list. d Select [DELETE] with v, then

To delete all the characters press z.

Select [DELETE ALL], then press z. All MODE dial the characters are deleted. e Select [OK] with v, then press z. • If you select [EXIT], authentication is The selected record is deleted. canceled and the connection is not established. f To delete other records, display the record you want to

If you fail to enter the passkey delete with b/B, select

If you run past the time limit for the passkey [DELETE], then press z. entry (30 seconds) or enter a different passkey, confirm error messages then Control button To cancel the deletion connect again. Select [CANCEL] in Step 5 or [EXIT] in a Set the MODE dial to SET UP. Step 6, then press z. b Select (Bluetooth SETUP) with V, [EDIT RECORD] with v/ V/B, [OK] with v/B, then press z.,

Additional information

Additional information

Receiving File types that can be

sent/received • The only files you can receive using your camera are JPEG files. • Received images are recorded in the

Sending recording folder. The file name format

used is as follows: The types of files you can send using your “NET0ssss.JPG”* and used it camera are as follows: depends also on the setting of [FILE • Still image files shot normally. NUMBER] in (SETUP 2). – In Multi Burst mode * ssss stands for any number within the • Still image files shot in range from 0001 to 9999. – E-MAIL mode • The settings for DPOF and protect are not – VOICE mode. valid in received images. • The files you can send using your camera are only JPEG files. • The image may be resized or only the thumbnail file may be sent depending on the connected device. • The settings for DPOF and protect are not valid in received images. • File name and storage destination depend on the connected device.

Received image file storage

destinations and file names on a

VAIO

For details, refer to the HELP of the VAIO., For details on your VAIO, refer to the

Troubleshooting HELP of the VAIO or the following

URL: http://www.sony-imaging.com/ If you have trouble with your camera, try support/ the following solutions.

Sending/Printing images

Symptom Cause Solution The Bluetooth button • The MODE dial is not set to . p Set the MODE dial to (see the operating instructions). does not work. • The playback zoom function is being used. p Cancel the playback zoom function (see the operating instructions). [SEND] or [PRINT] in the • The MODE dial is not set to . p Set the MODE dial to (see the operating instructions). Bluetooth menu cannot be • No “Memory Stick” is inserted. p Insert a “Memory Stick” (see the operating instructions). selected. • No images are in the selected folder. p Select the folder where the image is stored (see the operating instructions). • A movie or Clip Motion file is selected. p Select an image file other than Movie or Clip Motion files. The desired Bluetooth • The device is not turned on. p Turn on the device. For details, see the operating instructions device cannot be supplied with the device. discovered. • The device is not connectable. p Check that the Bluetooth function of the device is started up and the device is connectable. • The device ran past the time limit. p Set the device so that it is connectable and perform a new search (page 7). • The device is placed outside of radio wave range p Move the device closer to your camera. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The desired device is now connecting to another p Wait until the connection is finished and perform a new search device. (page 7). • The name of the device has been changed. p Check the name of the device. • More than 10 Bluetooth devices are found p The maximum number of devices discoverable using a new around your camera. search is 10. The order in which devices are discovered depends on existing conditions. Turn off all devices except the desired device, or repeat new searches until the desired device is found. • The name of the device is not found. p When a new search is canceled, the name of the device you are searching for may not be found. A substitute name (e.g., Device1) may be displayed instead. Identify the device address and type (page 35) and select it again or perform the new search again., Additional information Symptom Cause Solution You cannot connect to the • The device is not turned on. p Turn on the device. For details, refer to the operating desired device. instructions supplied with the device. • The device is not connectable. p Check that the Bluetooth function of the device is started up and the device is connectable. • The device ran past the time limit. p Set the device so that it is connectable and perform a new search (page 7). • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The desired device is now connecting to another p Wait until the connection is finished and perform a new search device. (page 7). • Passkey authentication failed. p Connect again and enter the same passkey both on your camera and the device (page 17). • You did not enter the passkey on the device. p Whether the passkey entry screen first appears on your camera or the device you intend to connect depends on the setting and the device. Connect again and enter the same passkey (page 17). • The device you intend to connect to is different. p Check the name on the SELECT THE RECEIVER screen. • The connection has been rejected. p Set the device so that it is connectable. For details, refer to the operating instructions supplied with the device. • Since passkey authentication has failed p Try to connect again after a while. repeatedly, the connection may be rejected for a while. • The device is not BIP-compatible. p The camera can connect to only a BIP-compatible device (page 4). You cannot select the • A movie or Clip Motion file has been selected. p Select an image other than Movie or Clip Motion file. desired image. • No images in the selected folder. p Select the folder where the image is stored (see the operating instructions)., Symptom Cause Solution You cannot send an image • The capacity of the media of the device (e.g., a p Delete data from the media (e.g., a “Memory Stick” or hard to the desired device. “Memory Stick” or hard disk) is full. disk) or replace it with a new one (see the operating instructions). • The device disconnected the connection. p Check the status of the device and try to connect to the device again. For details on the device, refer to the operating instructions supplied with the device. • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The application of the device suddenly stops. p Check the status of the device. For details on the device, refer to the operating instructions supplied with the device. • The MODE dial is not set to . p Set the MODE dial to and connect again (pages 8, 10). • Your camera has been turned off by rotating the p Turn on your camera and connect to the device again (pages 8, lens portion or for some other reason. 10). • The number of jobs to be printed by the printer p The number of images acceptable at one time depends on the is over the limit. printer. Wait until the printer is ready to accept images, then send images. For details, refer to the operating instructions supplied with the printer. • There is no paper in the printer. p Supply the printer with paper. For details, refer to the operating instructions supplied with the printer. • There is no ink in the printer. p Change the printer with ink. For details, refer to the operating instructions supplied with the printer. DPOF or protect setting is • The settings for DPOF or protect are not valid in — not valid. the received images.

Receiving

Symptom Cause Solution The Bluetooth button • The MODE dial is not set to . p Set the MODE dial to (see the operating instructions). does not work. • The playback zoom function is being used. p Cancel the playback zoom function (see the operating instructions)., Additional information Symptom Cause Solution [RECEIVE] in the • The MODE dial is not set to . p Set the MODE dial to (see the operating instructions). Bluetooth menu cannot be • No “Memory Stick” is inserted. p Insert a “Memory Stick” (see the operating instructions). selected. • The write-protect switch on the “Memory Stick” p Set the write-protect switch to the recording position (see the is set to the LOCK position. operating instructions). • The capacity of the “Memory Stick” is p Delete the images saved in the “Memory Stick,” or format it insufficient. (see the operating instructions). p Replace the “Memory Stick” (see the operating instructions). You cannot receive an • The sent file is not a JPEG file. p Send the JPEG file. image from the desired • The capacity of the “Memory Stick” is p Delete the images saved in the “Memory Stick,” or format it device. insufficient. (see the operating instructions). p Replace the “Memory Stick” (see the operating instructions). • The sent file is too large. p Large size files may not be acceptable. • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The desired device is now connecting to another p Wait until the connection is finished and perform a new search device. (page 7). • Passkey authentication has failed. p Connect again and enter the same passkey both on your camera and the device (page 17). • The device you intend to connect to is different p Check the name on the SELECT THE RECEIVER screen. from the currently selected., Symptom Cause Solution You cannot receive an • The capacity of the “Memory Stick” is p Delete images saved in the “Memory Stick,” or format it (see image from the desired insufficient. the operating instructions). device (disconnected). p Replace the “Memory Stick” (see the operating instructions). • The device disconnected the connection. p Check the status of the device and try to connect to the device again. For details on the device, refer to the operating instructions supplied with the device. • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The device disconnected the Bluetooth p Set the device so that it is connectable. For details, refer to the connection. operating instructions supplied with the device. • The MODE dial is not set to . p Set the MODE dial to and connect again (pages 12, 13). • The “Memory Stick” was removed. p Insert the Memory Stick” and connect again (pages 12, 13). • The camera has been turned off by rotating the p Turn on the camera and connect to the device again (pages 12, lens portion or for some other reason. 13). No request from the • The device is now connecting to another device. p Make a connection with your camera. sending device. • The camera ran past the time limit (about five p Set the camera so that it is connectable again (pages 12, 13). minutes). You cannot play back • Incompatible JPEG files or files shot using other — received images. cameras may not be properly played back on your camera. • The image is corrupted. — Thumbnail files on the • The received file has no thumbnail. p There are some cases that JPEG files received from a VAIO or index screen are other devices have no thumbnails. Such files are displayed in displaced in blue. blue on the index screen. However, this does not affect the actual image received. DPOF or protect settings • The settings for DPOF or protect are not valid in — are not valid. the received images. Black bands surround the • The image size does not correspond to that of p When the image size does not corresponds to that of your image. your camera. camera, black bands may appear around the image., Additional information

Remote camera

Symptom Cause Solution The Bluetooth button • The MODE dial is not set to , P, or SCN. p Set the MODE dial to , P, or SCN (see the operating does not work. instructions). • The camera is in quick review mode. p Exit the quick review mode (see the operating instructions). [REMOTE CAMERA] in the • The MODE dial is not set to , P, or SCN. p Set the MODE dial to , P, or SCN (see the operating Bluetooth menu cannot be instructions). selected. • No “Memory Stick” is inserted. p Insert a “Memory Stick” (see the operating instructions). • The write-protect switch on the “Memory Stick” p Set the write-protect switch to the recording position (see the is set to the LOCK position. operating instructions). • The capacity of the “Memory Stick” is p Delete the images saved in the “Memory Stick,” or format it insufficient. (see the operating instructions). p Replace the “Memory Stick” (see the operating instructions). • [MODE] (REC MODE) is set to [VOICE]. p Set [MODE] (REC MODE) to a position other than [VOICE] (see the operating instructions). No request from the • The device (controller) is now connecting to p Connect the controller to your camera. desired device. another device. • You did not enter the passkey on the device. p Connect again and enter the correct passkey. • The device you intend to connect to is different p Check the name on the SELECT THE RECEIVER screen. from the one selected. • The device is not a BIP-compatible. p The camera can connect to only a BIP-compatible device (page 4). • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The camera ran past the time limit (about five p Set the camera so that it is connectable again (page 14). minutes)., Symptom Cause Solution The connection is • The capacity of the “Memory Stick” is p Delete images saved in the “Memory Stick,” or format it (see disconnected. insufficient. the operating instructions). p Replace the “Memory Stick” (see the operating instructions). • The MODE dial is not set to , P, or SCN. p Set the MODE dial to , P, or SCN (see the operating instructions). • The “Memory Stick” was removed. pInsert the Memory Stick” and connect again (page 14). • The camera has been turned off by rotating the p Turn on the camera and connect to the device again (page 14). lens portion or for some other reason. • The device disconnected the connection. p Check the status of the device and connect to the device again. For details on the device, refer to the operating instructions supplied with the device. • The device is placed outside of radio wave p Move the device closer to your camera. range. • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). device is covered with your hand etc. • The device is disconnected the Bluetooth p Set the device so that it is connectable. For details, refer to the connection. operating instructions supplied with the device. • The camera ran past the time limit of the remote p The maximum time you can use the camera as a remote camera camera time limit (about three hours). is three hours. The camera automatically turns off after three hours. The shutter clicks even if • The shutter always clicks during the remote — you set it not to click. camera mode. The buttons do not • The buttons do not function during the remote — function. camera mode except for SMART ZOOM, POWER, and the MODE dial . The self-timer is canceled. • The self-timer cannot be used in the remote — camera mode. You cannot perform • The flash is being charged. p Wait until the charging is finished and perform remote shooting remote shooting. (see the operating instructions). • The capacity of the “Memory Stick” is p Delete the images saved in the “Memory Stick,” or format it insufficient. (see the operating instructions). p Replace the “Memory Stick” (see the operating instructions)., Additional information

Entering a passkey

Symptom Cause Solution The passkey entry is • The security level of the camera or the device p When raising the security level, passkey entry may be required requested. has been changed. even if you have connected to the device before. Enter the passkey (page 17). • The record has been deleted from the camera or p When deleting the record, the passkey entry may be required the device to which you intend to connect. even if you have connected to the device before. Enter the passkey (page 17). • The authentication valid period of your camera p When the authentication valid period of your camera is expired, is expired on the device you intend to connect to. passkey entry may be required even if you have connected to the device. Enter the passkey (page 17). • The device you intend to connect to is different p Check the name on the SELECT THE RECEIVER screen. from the one selected. The connection is • You ran past authentication time limit (30 p Enter the same passkey both in the camera and the device within disconnected from the seconds). 30 seconds (page 17). desired device. • The same passkey is not entered. p Enter the same passkey both in the camera and the device within 30 seconds (page 17). • The device disconnected or ended the p Set the device so that it is connectable. For details, refer to the connection. operating instructions supplied with the device (page 17). • You did not enter the passkey on the other p Whether the passkey entry screen first appears on the camera or device. the device depends on the setting and the device. Connect again and enter the passkey. • The camera is turned off by rotating the lens p Turn on the camera and connect to the device again. portion or for some other reasons. Authentication failed. • You ran past the authentication time limit (30 p Enter the same passkey both in the camera and the device within seconds). 30 seconds (page 17). • The same passkey was not entered. p Enter the same passkey both in the camera and the device within 30 seconds (page 17). • The device disconnected or ended the p Check the status of the device and try to connect to the device connection. again. For details, refer to the operating instructions supplied • The device you intend to connect to used a with the device (page 17). character not valid for the camera as a part of p Enter only valid characters (page 17). passkey.,

Others

Symptom Cause Solution Data transmission speed • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). is too slow. connected device is covered with your hand etc. — p Data transmission speed depends on the distance between your camera and the device, obstacles, radio wave conditions, application software, or the OS. Change the position of your camera or set your camera closer to the device. Since the distance • The antenna portion of your camera or the p Do not cover the antenna portion (page 4). between the camera and device is covered with your hand etc. the desired device is — p Data transmission speed depends on the distance between the within 10 m (3.3 feet), the camera and the device, obstacles, radio wave conditions, connection cannot be application software, or the OS. Change the position of your established. camera or set your camera closer to the device. • The desired device is now connecting to another p When the device is connecting to another device, the device device. may not be displayed as an available device or be connectable at that time. • The device is not connectable. p Set the device so that it is connectable. For details, refer to the operating instructions supplied with the device., Additional information

Warnings and

messages The following messages appear on the LCD screen. Message Meaning/ Corrective Action FAIL TO CERTIFICATE • You did not enter the passkey within 30 seconds. Enter it within 30 seconds (page 17). INPUT THE SAME LETTERS INTO THE DEVICE TO BE CONNECTED AND THIS DEVICE WITHIN 30 SECS. NO REQUEST FROM THE SENDER • If the camera does not receive any requests of connection or sending images from the device for NO REQUEST FROM THE CONTROL five minutes, the connection is disconnected or the camera becomes non-connectable. Connect again. NO RESPONSE FROM THE RECEIVER • If the camera does not receive any responses from a receiver/printer for 10 minutes, the NO RESPONSE FROM THE PRINTER connection is disconnected. Check the device status. DISCONNECTED • Since the device disconnected for some reason or the distance between the camera and the device is too great far, the connection was disconnected. REFUSED TO CONNECT • The connection was rejected by the device you intend to connect to by the setting or operations of that device. Change the setting of the device. REFUSED BY THE RECEIVER • The request to send an image, or the image itself was rejected. REFUSED BY THE PRINTER • You are trying to send or print an incompatible image. RECEIVER’S SERVICE IS • The device is not compatible with BIP features (page 4). NOT SUPPORTED PRINTER’S SERVICE IS NOT SUPPORTED NOT FOUND • The camera could not discover the desired device. Set the device to be connectable . ENABLE THE RECEIVER NOT FOUND ENABLE PRINTER TO RECEIVE, Message Meaning/ Corrective Action FAIL TO CERTIFICATE • The connection failed because a wrong passkey was entered. Enter the same passkey both on the INPUT THE SAME LETTERS INTO camera and on the device you intend to connect to (page 17). THE DEVICE TO BE CONNECTED AND THIS DEVICE COMMUNICATIONS ERROR • Communication error occurred. Connect again. UNABLE TO CONNECT • The desired device cannot be discovered because the device is turned off, is too far away to be ENABLE THE RECEIVER discovered, or other reasons. UNABLE TO CONNECT ENABLE PRINTER TO RECEIVE NOT ENOUGH MEMORY • The file size of the selected image is too large. NOT ENOUGH MEMORY ENABLE THE RECEIVER • The camera could not discover the desired device. Set the device to be connectable. ENABLE PRINTER TO RECEIVE NO RECORD FOR CONNECTED DEVICE • There is no record. Perform a new search (page 7). TRY A NEW SEARCH, Additional information Additional information

Menu items

Menu items of the Bluetooth function to make changes depend on the position of the MODE dial. The LCD screen shows only the items you can use based on the current position of the MODE dial.

When the MODE dial is set to , P or SCN

Item Description REMOTE CAMERA Uses the camera as a remote camera.

When the MODE dial is set to

Item Description SEND Sends an image to a BIP-compatible Bluetooth device (page 8). RECEIVE Receives an image from a BIP-compatible Bluetooth device (page 12). PRINT Sends an image to a BIP-compatible Bluetooth printer to print the image (page 16). When the MODE dial is set to or SET UP, the Bluetooth menu is not displayed.,

SET UP items

Set the MODE dial to SET UP. The SET UP screen appears. Factory settings are indicated by x. (Bluetooth SETUP) Item Setting Description SECURITY LEVEL HIGH / xLOW Sets the security level for a Bluetooth connection. When set to [HIGH], passkey entry is required for connecting to other devices for the first time (page 17). EDIT RECORD OK / CANCEL Deletes the record (page 18). CHANGE NAME OK / CANCEL Renames the camera (page 5). • The device address (page 5) is unique for each device. You cannot change this address., Additional information

Bluetooth

specifications Communication type Bluetooth standards, ver. 1.1 Maximum transmission speed1) About 723 Kbps Output Bluetooth standards, Power Class 2 Communication distance2) About 10 m (3.3 feet) without obstacles Compatible Bluetooth profile3) Basic Imaging Profile (Image Push Initiator, Image Push Responder, Remote Camera Responder) Frequency band 2.4 GHz (2.400 to 2.4835 GHz) 1) Maximum data transmission speed based on Bluetooth standards, ver. 1.1. This speed depends on the distance between the devices, obstacles, radio wave conditions, application software, or the OS. 2) This distance depends on the obstacles between the devices, radio wave conditions, application software, or the OS. 3) This specification is in accordance with the intended use between two Bluetooth devices. This is defined by the Bluetooth standards., L Playback folder indicator

The LCD screen M Change folder indicator

N Message area

Sending/receiving/printing/

using as a remote camera16273860min 640 FINE 10194Sony Cyber-shot 101 12/12 00:0C:3E:3A:4B:69 q; qa

SENDING

qs qd

EXIT

OK qf A Recording mode indicator F Image size indicator B Radio wave indicator G Image quality indicator ( , , ) (Use this as a guide) H Recording folder indicator C Battery remaining indicator I Remaining “Memory Stick” D Device name of the connected capacity indicator (4) device (5) J Number of images recorded in E Device address of the connected the playback folder device (5) K Image number, Additional information

Selecting the receiver/editing

the record SELECT THE RECEIVER 1/4 NAME : 3 1 Sony Cyber-shotX ADDRESS : 4 TYPE : CAMERA SUPPORTED : UNKNOWN 5 SEARCH : NEW CONNECT 6

EXIT

NEW SEARCH

OK

A Device name (5) B Record number/Total number of records C Device address (5) D Device type E Supported service “UNKNOWN” is indicated when a device has not been connected. F Search result (7) After you perform a new search, “SEARCH” is added. A newly discovered device is indicated as “NEW.”,

Index

JPEG ... 19 T

Index Thumbnail image ... 19 N Time limit A Naming your camera ... 5 Passkey entry ... 17

Antenna portion ... 4 New search ... 7 Using as a remote camera ... 14 Type ... 35

B O

BIP Output ... 33

W

Image Push Feature ... 4 Warning messages ... 29 Remote Camera Feature ... 4 P Bluetooth button ... 4 Passkey Bluetooth lamp ... 4 Passkey entry ... 17 Bluetooth wireless technology ... 4 Print ... 16 Time limit ... 17

C

Changing the name ... 32 R Communication distance ... 33 Receive Image file types ... 19

D Receiving ... 12

Device address ... 5 Record ... 18 Device name ... 5 Remote camera ... 14 Remote Camera Feature ... 4

F

File S File name ... 19 Search result ... 35 Storage destination ... 19 Security level ... 32 Frequency band ... 33 Send Image file types ... 19

I New search ... 7

Sending to a camera ... 8 Image Push Feature ... 4 Sending to a VAIO ... 10

J

, Printed on 100% recycled paper using VOC (Volatile Organic Additional information on this product and answers to frequent Compound)-free vegetable oil asked questions can be found at our Customer Support Website. based ink. Sony Corporation Printed in Japan307966411,

Reverse 992999743.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2002.10 Official Release — — 1.1 2003.02 Supplement-1 • Addition and change of accessories No (S1 PV02-011) • Addition of E, Hong Kong, Australian Mod- els (FX77) 1.2 2003.04 Supplement-2 • Addition of Korea Model (F77) No (S2 PV02-024)]
15

Similar documents

SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL i
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-F88 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.05 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
DSC-H2 SERVICE MANUAL LEVEL 2 US Model UK Model Chinese Model Korea Model Tourist Model
DSC-H2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006. 02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Argentina Model ON BOARD Hong Kong Model Korea Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WI
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1
DSC-H1 SERVICE MANUAL LEVEL 2 DSC-H1 Ver 1.2 2005. 09 US Model Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model How to use Australian Model Acrobat Reader Chinese Model Japanese Model Korea Model Tourist Model Internal memory ON BOARD Link SPECIFICATIONS BLOCK DIAGRAMS PRIN
SPECIFICATIONS Camera
DSC-H7/H9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2007.04 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: DSC-H7 Black Model Brazilian Model Tourist Model J
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-L1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTR
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-L1 SERVICE MANUAL LEVEL 2
DSC-L1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Chinese Model Korea Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Revision History Australian Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION
DSC-M1 SERVICE MANUAL LEVEL 1 DSC-M1 Ver 1.1 2005. 12 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model Hong Kong Model Korea Model Japanese Model Link SPECIFICATIONS ACCESSORIES SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.0 2004. 11 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.1 2005. 04 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1
DSC-M1 SERVICE MANUAL LEVEL 2 DSC-M1 Ver 1.2 2005. 09 US Model Canadian Model Revision History Australian Model Chinese Model E Model Tourist Model How to use Hong Kong Model Acrobat Reader Korea Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMAT
DSC-N2 SERVICE MANUAL SUPPLEMENT-1
DSC-N2 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.02 SUPPLEMENT-1 File this supplement with the service manual. (PV06-161) • Addition of Brazilian Model • Change of Automatic Adjustment Program • Addition of Brazilian Model & : Points added portion. INITIAL LANGUAGE Default Data Check (Service manual pag
DSC-N2 SERVICE MANUAL Canadian Model
DSC-N2 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.1 2007.02 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model SUPPLEMENT-1 File this supplement with the service manual. (DI06-165) • Addition of
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model UK Model Hong Kong Model Argentine Model Japanese Model Tourist Model Link
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-N2 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Argentine Model Brazilian Model Japanese Model
DSC-N2 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory ON BOARD Korea Model Argentine Model Brazilian Model Japanese Model Tourist Model Link SPECIFICAT
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.0 2004.04 US Model Canadian Model Revision History E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P100/P120 AEP Model UK Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.2 2004.07 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Correction of exploded view
DSC-P100/P120 LEVEL 2 DSC-P100 SERVICE MANUAL Canadian ModelChinese Model Korea Model Tourist Model Ver 1.2 2004.07 Japanese Model DSC-P100/P120 US Model AEP Model CORRECTION-1 UK ModelE Model Hong Kong Model We will inform you that there are printing errors Australian Model in the service manual pr
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick” and battery
DSC-P100/P120 SERVICE MANUAL LEVEL 1 DSC-P100 Ver 1.1 2004.06 Canadian Model Chinese Model Revision History Korea Model Tourist Model Japanese Model DSC-P100/P120 US Model AEP Model UK Model E Model Hong Kong Model Australian Model Photo: DSC-P100/Silver Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION O
• Change of repair parts
DSC-P10/P12 LEVEL 2 US Model SERVICE MANUAL Canadian ModelDSC-P10 AEP Model Ver 1.5 2004. 05 UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model SUPPLEMENT-3 Tourist ModelJapanese Model File this supplement with the service manual. DSC-P10 (PV04-005) • Change of t
Should the fuse in the plug supplied need to be
DSC-P10/P12 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History DSC-P10 AEP Model UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: DSC-P10 DSC-P10 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAM
Should the fuse in the plug supplied need to be
DSC-P10/P12 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2003. 12 Canadian Model Revision History DSC-P10 AEP Model UK Model DSC-P10/P12 E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: DSC-P10 DSC-P10 Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAM
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-P150 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2004.08 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Brazilian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINT
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-P150 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.04 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Brazilian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINT
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-P150 SERVICE MANUAL LEVEL 1 US Model Ver 1.1 2005.04 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Brazilian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INS
SPECIFICATIONS xCamera [LCD screen] xAC-LS5/LS5B AC Adaptor
DSC-P150 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.08 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Brazilian Model Chinese Model Korea Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INS
SPECIFICATIONS Camera [Power, general] NP-FR1 battery pack
DSC-P200 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2005.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAME