Download: DSC-P3 SERVICE MANUAL US Model Level 2 Canadian Model E Model Hong Kong Model Ver 1.2 2001. 12 Australian Model Chinese Model Korea Model Tourist Model

DSC-P3 SERVICE MANUAL US Model Level 2 Canadian Model E Model Hong Kong Model Ver 1.2 2001. 12 Australian Model Chinese Model Korea Model Tourist Model Japanese Model Photo: SILVER model This service manual contains information for Japanese model as well. On the DD-163, SY-73 boards SY-73 board This service manual provides the information that is premised the Schematic diagram ... Page 4-15 to 4-36 circuit board replacement service and not intended repair inside the Printed wiring board ... Page 4-11 to 4-14 DD-163, SY-73 boards. Electrical parts list ... Page 6-10 to 6-15 Therefore, schematic...
Author: Acal1978 Shared: 8/19/19
Downloads: 138 Views: 1548

Content

DSC-P3 SERVICE MANUAL US Model Level 2 Canadian Model E Model Hong Kong Model Ver 1.2 2001. 12 Australian Model Chinese Model Korea Model Tourist Model Japanese Model

Photo: SILVER model This service manual contains information for Japanese model as well.

On the DD-163, SY-73 boards SY-73 board

This service manual provides the information that is premised the Schematic diagram ... Page 4-15 to 4-36 circuit board replacement service and not intended repair inside the Printed wiring board ... Page 4-11 to 4-14 DD-163, SY-73 boards. Electrical parts list ... Page 6-10 to 6-15 Therefore, schematic diagram, printed wiring board and electrical parts list of the DD-163, SY-73 boards are not shown. DD-163 board The following pages are not shown. Schematic diagram ... Page 4-47 to 4-52 Printed wiring board ... Page 4-43 to 4-46 Electrical parts list ... Page 6-6 to 6-8 The above-described information is shown in service manual Level 3.

SPECIFICATIONS

! ! " "#$ !%& '( ) F ?FF& ?F& GF HF < 5$> ,;$7 G?F& H?F& B.=&>$ $7 <# -< = ( % Ω, GF HF ( =D1 ! '>$$ #( 5$ " G?F& H?F& %AA% $#$ '#- <$ $? 7Ω ? ?A A ? .! # $# %A%A ! # '#5$' :1@$> +' ' #$ - 7Ω ? A A ' C $ %* + , ! # '#5$' ( 6, 1 78,@ ! =@ ' 5? I =9+,:1@#" " # $% ( 1.<=? $ $ - ? 5 I 4/2 -35 , + $ 5* ' % - '#5>$ $7B.= % & D '>$ 5$# $ $ % 3&33 &(6, 1 78$# &3$ $ " $ ! $ ( ( '>; $5 ! ' ' $ ' #" ? < *2 & / # 4 ' $ ()#(*#( +' # %A # *2 , < $ $7 - . ? C % ," -,./0 % , "-23" 1 -2./0(0*&3/43 B.=& "- 0 # ( , (3*&& /0 1 /0 1 '#! $5 - < ? <(% )I ,./0,$'$ /0 ' ) ? <(% $ 5 6, 1 78 ? C CD # @ED*0)3-@9*0)3 ! 9 # # #5 B+9,D F ?FF& ?F& # $ *1+ :3+- % CD@ED*0)3- DIGITAL STILL CAMERA +&&, SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED À LA SÉCURITÉ! LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 AND IN THE PARTS LIST ARE CRITICAL TO SAFE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE OPERATION. REPLACE THESE COMPONENTS WITH DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ SONY PARTS WHOSE PART NUMBERS APPEAR AS DE FONCTIONNEMENT. NE REMPLACER CES COM- SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-sol- 4. Look for parts which, though functioning, show obvious signs dered connections. Check the entire board surface for solder of deterioration. Point them out to the customer and recom- splashes and bridges. mend their replacement. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. “pinched” or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, particularly transis- • Keep the temperature of the soldering iron around 270 ˚C tors, that were installed during a previous repair. Point them during repairing. out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when sol- dering or unsoldering. – 2 –,

TABLE OF CONTENTS

Section Title Page Section Title Page SERVICE NOTE... 5 5. ADJUSTMENTS Before Starting Adjustment ... 5-1 1. GENERAL 1-1. Adjusting Items when Replacing Main Parts and Boards ... 5-2 Introduction ... 1-1 5-1. Camera Section Adjustment ... 5-3 Identifying the Parts ... 1-2 1-1. Preparations Before Adjustment ... 5-3 Preparing the Power Supply ... 1-2 1-1-1. List of Service Tools ... 5-3 Setting the Date and Time ... 1-3 1-1-2. Preparations ... 5-4 Inserting the “Memory Stick” ... 1-4 1-1-3. Discharging of the Flashlight Power Supply ... 5-4 Basic Operations ... 1-4 1-1-4. Precautions ... 5-6 Recording Still Images ... 1-4 1. Setting the Switch ... 5-6 Recording Moving Images ... 1-6 2. Order of Adjustments ... 5-6 Playing Back Still Images ... 1-7 3. Subjects ... 5-6 Playing Back Moving Images ... 1-7 4. Preparing the Flash Adjustment Box ... 5-7 Viewing Images Using a Computer ... 1-7 1-2. Initialization of B, D, E, F, 7, 9 Page Data ... 5-8 Viewing Images on Windows ... 1-8 1-2-1. Initialization of D Page Data ... 5-8 Viewing Images on Macintosh ... 1-10 1. Initializing D Page Data ... 5-8 Image File Storage Destinations and Image Files ... 1-11 2. Modification of D Page Data ... 5-8 Before Performing Advanced Operations ... 1-11 3. D Page Table ... 5-8 Various Recording ... 1-13 1-2-2. Initialization of B, E, F, 7, 9 Page Data ... 5-9 Various Playback ... 1-16 1. Initializing B, E, F, 7, 9 Page Data ... 5-9 Editing ... 1-17 2. Modification of B, E, F, 7, 9 Page Data ... 5-9 Additional Information ... 1-20 3. B Page Table ... 5-9 Troubleshooting ... 1-21 4. E Page Table ... 5-9 Warning and Notice Messages ... 1-22 5. F Page Table ... 5-10 Self-diagnosis Display ... 1-23 6. 7 Page Table ... 5-12 Display Window Indicators ... 1-23 7. 9 Page Table ... 5-13 LCD Screen Indicators ... 1-23 1-3. Video System Adjustments ... 5-14 1. Video Sync Level Adjustment ... 5-14 2. Video Burst Level Adjustment ... 5-14 2. DISASSEMBLY 1-4. Camera System Adjustments ... 5-15 1. HALL Adjustment ... 5-16 2. Flange Back Adjustment (Using the Minipattern Box) .. 5-17 2-1. BT Lid ... 2-2 3. Flange Back Adjustment 2-2. Cabinet (Front) Assembly ... 2-2 (Using the Flange Back Adjustment Chart) ... 5-18 2-3 Cabinet (Rear) Assembly ... 2-2 4. Flange Back Check ... 5-19 2-4. LCD Module ... 2-3 5. Picture Frame Setting ... 5-20 2-5. Lens Block Assembly ... 2-3 6. F No. Standard Data Input ... 5-21 2-6. Mode Dial Block Assembly ... 2-4 7. Mechanical Shutter Adjustment ... 5-21 2-7. Cabinet (Bottom) Assembly ... 2-4 8. Light Value Adjustment ... 5-22 2-8. SY-73 Board ... 2-4 9. Auto White Balance Standard Data Input ... 5-23 2-9. Memory Stick Connector ... 2-4 10. Auto White Balance Adjustment ... 5-24 2-10. ST-67 Board ... 2-5 11. Auto White Balance Check ... 5-25 2-11. DD-163 Board ... 2-5 12. Color Reproduction Adjustment ... 5-26 2-12. Circuit Boards Location ... 2-6 13. Color Reproduction Check ... 5-27 14. CCD White Defect Compensation ... 5-28 15. CCD Black Defect Compensation ... 5-29 3. BLOCK DIAGRAMS 16. Strobe White Balance Adjustment ... 5-30 1-5. LCD System Adjustments ... 5-31 3-1. Overall Block Diagram ... 3-1 1. LCD Initial Data Input (1) ... 5-32 3-8. Power Block Diagram 1 ... 3-15 2. LCD Initial Data Input (2) ... 5-32 3-9. Power Block Diagram 2 ... 3-17 3. VCO Adjustment (SY-73 Board) ... 5-33 4. Black Limit Adjustment (SY-73 Board) ... 5-34 4. PRINTED WIRING BOARDS AND 5. Bright Adjustment (SY-73 Board) ... 5-35 SCHEMATIC DIAGRAMS 6. Contrast Adjustment (SY-73 Board) ... 5-36 7. Color Adjustment (SY-73 Board) ... 5-36 4-1. Frame Schematic Diagrams ... 4-3 8. VG Center Adjustment (SY-73 Board) ... 5-37 Frame Schematic Diagram (1/2) ... 4-3 9. PSIG Adjustment (SY-73 Board) ... 5-37 Frame Schematic Diagram (2/2) ... 4-5 10. V-COM Adjustment (SY-73 Board) ... 5-38 4-2. Printed Wiring Boards and Schematic Diagrams ... 4-7 11. White Balance Adjustment (SY-73 Board) ... 5-38 CD-340 Printed Wiring Board ... 4-7 1-6. System Control System Adjustments ... 5-39 CD-340 Schematic Diagram ... 4-9 1. Battery Down Adjustment ... 5-39 Control Switch Block Schematic Diagram ... 4-37 5-2. Service Mode ... 5-40 FP-380 Schematic Diagram ... 4-37 2-1. Adjusting Remote Commander ... 5-40 SW-364 Printed Wiring Board and 1. Used the Adjusting Remote Commander ... 5-40 Schematic Diagram ... 4-38 2. Precautions upon Using ST-67 Printed Wiring Board ... 4-39 the Adjusting Remote Commander ... 5-40 ST-67 Schematic Diagram ... 4-41 2-2. Data Process ... 5-41 4-4. Parts Location ... 4-56 2-3. Service Mode ... 5-42 1. Setting the Test Mode ... 5-42 2. Bit Value Discrimination ... 5-42 3. Mode Dial Check (1) ... 5-42 4. Mode Dial Check (2) ... 5-42 – 3 –, Section Title Page 5. Switch Check (1) ... 5-42 6. Switch Check (2) ... 5-43 7. LED Check ... 5-43 8. Self Diagnosis Code ... 5-43 6. REPAIR PARTS LIST 6-1. Exploded Views ... 6-1 6-1-1. Cabinet (Front) Assembly ... 6-1 6-1-2. Cabinet (Rear) Assembly ... 6-2 6-1-3. Lens Block and LCD Section ... 6-3 6-1-4. Battery Holder Assembly ... 6-4 6-2. Electrical Parts List ... 6-5 * The color reproduction frame is shown on page 119 . – 4 –,

SERVICE NOTE

• NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector. bent at the terminal. It is possible that a wire is snapped. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) • When repairing this device with the power on, if you remove the SW-364 board or CABINET (FRONT) assembly, this de- vice stops working. In this case, you can work without the device stopping by fas- tening the hook of the LENS COVER OPEN/CLOSE switch (S201) on the SW-364 board with tape. S201 – 5 –, [Discharging of the ST-67 board’s charging capacitor Discharging the Capacitor (C008)] Short-circuit between the positive and the negative terminals of charged capacitor with the short jig about 10 seconds. The charging capacitor (C008) of the ST-67 board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the R:1 kΩ/1 W (Part code: battery is handled by hand. The electric shock is caused by the 1-215-869-11) charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to pre- vent electrical shock. Capacitor 1 kΩ/1 W Wrap insulating tape. – 6 –, [Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss You can reverse the camera mal- function yourself. (However, con- tact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or lo- cal authorized Sony service facil- ity. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61: Checking of lens drive circuit. When failed in the focus and zoomss initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. – 7 –,

SECTION 1 GENERAL This section is extracted from

instruction manual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ntroduction 7 / E; E;$ $ ! ! ( Check images after recording 1$( ! .."..K$ 4! ! & 0 ! $$$ " 0! " 50 ! . C ! 0 2 ! ! & " ! ! *) E; E; ; ! ! ;=E=/=& $ ! $"/ ! - $$! $ ! $$ $ $ ! 0 " ! " 7 1 $ 0 ! 00 "= ! E; " 6 $ Capture images with your computer 7 / $ 0 ; ! ! $ ! , ! 0 $ ! $ $ " ! ( ! A'1 @=#/>@ $ 0 " = #$ / ! ( 9 D0! ! ! & ! < # > ", H ! ! $ 4! ! $( =(:>#E& ! 33 % ;4(/4D).=C ! 0 "#$ /4D.C/4D.=;'(;- $ ! )* ;'(;- $0 $ 0 0 "/ $ ! " " . 7 2 $ ! 0 / $ % 0 " $ ! 0 % $ ! " " * Record moving pictures (MPEG Movie or Clip Motion) / ! $ / ! ! ! " 0 :2=G:+D#=& A J!$ ! * $ ! 0 " ( # $ ! 7:' 8 ! 0 ! " ( Select from various recording modes 6 ! : & ! 3. / ! >! $ ! D+#=& ! 3 " 4! /=I/& ! 3- 4! ! $ /#& ! 3) 5 3 1-1,

Getting started Identifying the parts

Attaching the strap ' ! $ $ " A ' 6 8<=>: F ' M 6 8<;5A: U *!$/8<3: B - 8<;: G . ? N & 8<: V C6 8 : & //H#E#G5/ ; 0 !" ' ? @ 8: 8): /@&8 : "(/D@68H& 9 9 & / ! & 8 : 6:8AA: D+#= I ' ? 8)>:@ 8: W , 9 & / & 83: O ( 9 98=3: ! X /'/6 8;A:J + P +( 8=A: & /! ! Y . @1-' 2 : ! K + !*/"@+!'/ 6 Q ('*+@+(!"@!&&6 8<: Z . B 8<4: '=/A2&/ L 86 R -/" 6 8<;5A: ) : wj 8<>: CA00! $ S ("B8<<<5: *!$/6 8<3: wk E 3"3-C<* ", D & 85: 0 $ T 8 '.:B8)A: wl @F! B8>4: ! ! E > "* 990! ; 0 !0 " $ " ; =

Preparing the power supply Charging the battery pack

, ! 0 "1 $$ "

Installing the battery pack

, 0 7#$E#/5#A:82( L Battery pack (C type) ", "' ! )$ $ 7#$E#/5#A:8 " To wall outlet (wall socket) DC IN jack Jack cover Power cord (mains lead) AC-LS1A AC power adaptor (supplied) Battery eject lever162! B ( 6 ("B9v1! 6 @1-' 2 ' $ 0" 3 98 : 9 9 89 : 2 6 / 00$ 0 !! # 0 v $ ! 0 ! "H $ ! " " 0 0 ! $ $ ! 3 6 @1-' 2 ! 7 8 00"

To remove the battery pack After charging the battery pack

+ C7:' 8"' B 00 ; >0 $ ;#B $ " " 1 $ 0 ! " Battery remaining indicator / E; 0 ! $0 ! " 7#$E#/5#A:8 0 !$ H !! 0 $ ! 0 E; 0 % "/ 0 +"/ ! 7#$E#/5#A:8 "7#$E#/5#A:8 $ ! " "7#$E#/5#A:8 $' "

Recommended charging temperature

H !! $ 0 <3 )" <4 << 1-2 % %,

NP-FC10 battery pack ' 6GG

H ! ! E; NP-FC10 (supplied) ! "H ! 0 Battery life (min.) Number of images B $!"H ! E; + >" >"* " > $ $ ! 0 $

Power save mode ! $*3-O) ! J

% +4:>E!" H M2+H=4'>D=N '=/A2 M+N $0 ∗∗ 2 ! ! ! <( 0 ! ! "/ $ ! M+N ! )" -

When [POWER SAVE] is [ON] (page 81) NP-FC10 (supplied)

7 / E; $$0 $ ! !0 $ ! LCD screen OFF (min.) LCD screen ON (min.) $ !L"H $ $ $ ! $ $ !$ $ 0 ! !" ! >". >" L#$ !! $ ! ! " > ! 0 $ ! $ 7 / $0 ! *3- O* ! J" ! ! 0 M2+H=4'>D=N M+N" / ! 0 ! ! .K$0 7 / $ !0 $0000$ !" $ ! "

P

7 / $ $ ! 0 $ 0 $ 0C$$"

Battery pack Full charge (min.) Normal charge (min.) 7H E;1>?E#G5/ 14#G5/ $ $ ! 0

" 2( >"3 >". 7 / $ ! 0 !"/ ! " > ! ! ! 7 / $ 7:' 8 "/ $! $!0 >(E'>>0 $*3-" C 0 ! 7:' "8 7 7((((8 00 ! " 7;! !! 00 $ . 6 6@ $ 0! " 66H" 6 H >0 " ' G6H$ "

NP-FC10 (supplied) 7H E; $$ $

! "

Battery life (min.) Number of images 7 #$ $$ ! 0 $ !

E; + >" >"* ! " 7; ; ! >0 0 $ E; + >". >") ; !$ "A 0 ; !"A ! ! ! ! !! ! " > $ $ ! 0 $ ! $*3-O) ! J % +4:>E!" ∗ 2+H=4'>D=+ ! ( < <)

Using the AC power adaptor Setting the date and time

H $ "#$ E+?'=/ 0 0 " To wall outlet (wall socket) POWER lamp Power cord DC IN jack Jack cover (mains lead) Control button Select the item with vVbB, then set with AC-LS1A AC power adaptor (supplied) the center z. 1 ! B ( 6 ("B9v298 : 9 9 89 : 1 '

Using your camera abroad 2 * 9 *!$/6 POWER

! )3" 9 / 2+H=4 ! ! "

When using the AC power adaptor / E+?'=/ E; ON/OFF(CHG)

100"#$ $ " !$ 0 0 " 3 ' 9 v@V6zCLOCK SET Y / M / D M / D / Y ' $M,C:C;NCCM:C;C,N D / M / YCCM;C:C,NCC" 2001 / 1 / 1 12 : 00 OK

AM CANCEL OK

4 ' 9 9 b@B 6 CLOCK SET Y / M / D M / D / Y / 0 vCV" D / M / Y 2001 / 1 / 1 12 : 00 OK

AM CANCEL OK

<5 <3 1-3 % %, 5 ' 9 v@V Inserting the “Memory Stick” 6 z CLOCK SET Y / M / D M / D / Y >$ ! vCV D / M / Y " 2001 / 7 / 1 12 : 00 OK

AM

#$ M;C:C,N 3 CANCEL *( " OK 6 ' H!IJ9B6z6CLOCK SET Y / M / D M / D / Y / " D / M / Y 2001 / 7 / 4 10 : 30 OK Access lamp

PM CANCEL OK

! 6 @1-' 2

To cancel the date and time setting 1 ' $ 0"

' M>=EN0 vCVCbCB z" 2 1-' 2 # 7:' 80 B $ ! 0 " ' '=/A2 ! ) ! E+? '=/ '=/A2" 3 6 @1-' 2

P

#$ ! $ ! ! )< E+?'=/ 1-' 2 0 ! "H !$ 3 " + C7:' 8 7:' 8 ! " P Connector 7 # 7:' 8$ 0 ! 7:=:+4,'/#?=44+480 " 7H ! 0 " 7:' 8 $$ 0 Erasure !" prevention 7 , ! switch 7:' 8$ Label space 0 E+? " ∗ / $ 0 $$! $7:' 8 "

Basic operations B Recording Basic operations Recording still images

' ! @2=G$ "

How to use the mode dial .

*!$/6 9 1-' 2 / 0 $ 0 $! !"' $ 0 $ ! " : To record still images in TWILIGHT mode (pages 19, 54) : To record still images, VOICE mode audio data (pages 19, 56) : To play back or edit images (pages 28, 29, 71) POWER : To record moving images or Clip Motion images Lens cover (pages 26, 59) OPEN/CLOSE tab SET UP: To set the setup items (page 80)

How to use the control button When the menu is not displayed

/ $ $ 0! " (v): Recording with flash (page 24) (V): Recording with self-timer (pages 23, 27) 1 ' 7 (b): Checking the last recorded image (page 22) (B): Recording close subjects (macro recording) (page 61) 2 * 6 99 / ! "H >=C> z $ ! B $ $ !"H $

When the menu or setup screen is displayed B >=C> z ! $$ ! ! L

/ ! $!" E; $ $ ! " #$ !0 " Select Enter (OK) @ 6 8 : +( AE/AF lock indicator (green) flashes t lights up 0 EV ∗ #$ $ !>=C> ! $ ! 0 B $$ $ B "4 $ ! " Press MENU to display/ 0 EV clear the menu on the EV WB ISO LCD screen. Menu , $ 0 E; $$" <; <= 1-4 % BBBB, 3 * 6 9 , / " 5 $! $ 74=+4;#G8 E; !0 0 ! ! " 7:' "8H 74=+4;#G8 !"

RECORDING Auto power-off function

#$ $ !! $$ 0 !0 "/ ! 2+H=4 ! "/ 0($$$ 0 ! ! " / 0($$$ 0 0 ! ! ! ! 0 ! )0 !! A'19B;#B >CD+A/B " , !$$ E; ! !

The number of images you can record on a “Memory Stick” $"

(8 MB) = ;'2ECE;+C+ $ E; ! $ 0 & ' ! 3< 3 " ' ! .$ $ " / E; ! " P > " 7 / $ 0! 0 >=C> $$ r !" / E; ! " 6 H ! ! B E; !" H ! ! " 6 H ! B E; ! " r 7 #$ $ 0 2 ! $ / E; ! $$" B "50 ! 0 $ ! ! ** $ !";! !! $ " DSPL/LCD ON/OFF 4 <

Indicators in the finder

Self-timer/recording lamp (red) AE/AF lock lamp (green) Digital zoom button W side: for wide-angle (subject appears farther away) Flash charge lamp (orange) P T side: for telephoto (subject appears closer) 7, ! !0 $"4!0 E; 0 ! !" 7 1 $ $$ $ $ E; 0 B < C$ " / ! J$ 0 !$ $ <×";! 7H M;=:+N M+N '=/A2 ! $$ E; J ! ! ! !" " ;! J 0 E; $$" 7, $$ E; ! '=/A20 ! " 7, $$ $( $

P

" 7 / E; " 7;! J 0$! ! " 7 A E; 0 !! J$ ";! J ! $" 7 / >$ ! ** E; " 9 +( H !0 E; ! >$ $ 0 B " ? H $( $ B $ " AF frame Shutter button Self-timer lamp Control button 8K 9: , ! ! $ ! ) !b7 " 2 ! " ! )" b7 ! " *"2 V " / $( E; $ "; " B "/ $( $ $ " *"' M;=E=/=N0 B z" <"' M+?N0 v z" To cancel the self-timer recording2V! " ) 1-5

BBBB BBBB

, 9 9 & # $ 0 ! "/ / > $ ! $ B "' M>#EEA:#>/+4N $ ! "/ ! $ ! ) M+N '=/A2 ! " E; ! ) v $ > ! 0 $0 $ E; " " AF illuminator Control button v ( ) = v ! $ 0 " tttP$ & / $ ! $ ! ! " 7 #$> ! B $$ B $ & / $ " $ 0 "> $"< *"-C) - $ C* " , ! ! $ $ 0 M PNE>'5E=D=E 7 #/H#E#G5/ > 0 ! 0 $ $ " ! ! )" 7 ! > ! B $ ! ! $ $ B "

To reduce the red-eye phenomenon 7 / > 0 B !$ "

' M4=;=,=4=;A/#+N M+N '=/A2 ! ! )"/ $ 7 / > ! ! "> ! $ ! ( $! ( "H M+N 9 " E; "

P

7H M#'+N M>A/+N ! ! ! ($ "< <" -C) . $ C) "H M>A/+N $ $$ $ $ !" 7 4( $$ ! $$ B $ B ( " 7 / $ $$ 0 $$ ! " 7H !! $ $ ! $ ">$ !! ! " 7 / $ $ 0 !! ! ! : !1A4'/*" 7H ! 0 $ 0 ! !" 5 3

Recording moving images 6 * 6 9

74=8 E; !$ ! :! ! 0 :2=G$ ! 3" 7:' 8 ! " . *!$/6 9 1-' 2 7 * 6 9 / ! " H ! <*5Q J&/ ! 3 ! 3*" H ! <*O*O* J &/ ! 0 POWER 7:' 8 $ " Lens cover ! J 7' ! ! J#:>G='#F=8 OPEN/CLOSE tab !3*" ? DSPL/LCD ON/OFF H $( $ B $ " " ! )" *"2 V " / $( E; ! 1 ' '/ * $ "/ $( $ $ " 2 ' H J8-/:9 v@V CAMERA6BTo cancel the self-timer recording MOVING IMAGE: MPEG MOVIE DATE/TIME: OFF2V! " RED EYE REDUCTION: OFF AF ILLUMINATOR: ON +( PAGE SELECT = ;'2ECE;+C+ $ E; ! 3 ' H-!F"%-%/J9 v@V $ 0 & t $$t E; $$"CAMERA6B/ "' ! .-$ $ MOVING IMAGE: MPEG MOVIE DATE/TIME: CLIP MOTION " RED EYE REDUCTION: AF ILLUMINATOR:

P

$ 9 #$

OK

0 $$ 0 0 ! ! ! ! $ "HE0! 4 ' H-*/%-!F/J9 v@V CAMERA ! $ " 6 z MOVING IMAGE: MPEG MOVIE DATE/TIME: OFF RED EYE REDUCTION: OFF AF ILLUMINATOR: ON PAGE SELECT 5 '

A >

1-6

BBBB BBBB

,

BPlayback Playing back still images Playing back moving images

6 *!$/696*!$/6 9 1-' 2 1-' 2 POWER POWER DSPL/LCD ON/OFF DSPL/LCD ON/OFF 1 ' / ! ! E; " 1 ' / ! ! E; " 2 ' 9 640 6 b@B 6/8 2 ' 9 320 6/8 b&/ ! !" 6 b@B 0:00 &/ !" :! ! ( J B ! " b&/ ! !" 100-0028 20017410:30PM FILE BACK/NEXT VOLUME B&/ !" MOV 00001 20017410:30PM PLAY FILE BACK/NEXT VOLUME 3 * z 6 320P66/8 4:45 7,! ! 0 / ! ! " % " ;! B E; 7, ! 0 ! ! J " 0 " 7>! ! $ 0 !" MOV 00001 20017410:30PM STOP REV/CUE VOLUME Playback bar +( 6 = ;'2ECE;+C+ $ E; ! t t To pause playback $ 0 & $$ E; $$" ' ! .)$ $ " 2 z "

To advance or rewind the moving image

2 bCB! " / z " ; =

Moving images recorded with the image of [320 (HQ)]

(page 52) Viewing images using a computer / ! " , 0 0 $ ( ! $ 0 "/ $0!

B ! ! A'1 "

2 vCV B " / A'1 $ !$ 7:' 8$ " # A'1 A'1 +( 6 $ " 1 $ $ = ;'2ECE;+C+ $ E; ! $ 0 " $ 0 & t $$t E; $$" ' ! .)$ $ " / 00 A'1 0 2/2 "/ !MA'1+=/N '=/A2 ! ! )"/ $ ! M+4:>EN" / 0 ! M+4:>EN !"A 0 $ '0 0 2/2 " F 9 $ 9 #) F 9 - #5< " #5)

P

7; 0 $ 0!$ ": $ $ " 6 ' ! /=I/ &@2=G$ 6 :! ! C &:2=G$ 6 A ! &/#$ 6 /=I/C : &G#$ 7;! $ 0 $ J 0 !$ " 7H ! $ 0 0 $0 ! $ 0 0 $ $ 7#E==44+48 ! !" 7;! $ 0 $ $ $ : $ " 7Communications with your computer (for Windows only) 0 $ ! $' ' " 7: $ H0 H0 : ! $ : $ A ' C " 7: : +' Q/ ! $> #" 7 > ! $ " 7R8 7S8 " )4 )< 1-7

BBBB*6 BBBB*6

,

Viewing images on Windows 2 (?!- (?!-

+'& : $ H0 .)H0 .)'=H0 *2$ H0 : = / +' $ " + ! ! " 2A& ::I2 *:5J$ / A'1 " H0 : 2 ! " P The title screen appears after a moment. 7 #$ 0A'1% ! % ! $A'1% " 7+ ! 0 ! " 7+ ! $ " 1 Double-click “My Computer.” 2 Double-click the CD-ROM (“PhotoSuite (E:)”). ∗ / =& " $$! " '. 1$ ! A'1 "/ A'1 0 $ 0 ;(4+: 0 0 "

PCaution

. '. 6 ,The title screen appears after a moment. '.6966'. 3 - 98 : 1 '.( $ 9 =;@=;'/@- $ 9 4442 ' )3 '.69696Left-click here. 1 9$ 9 ; A'1 " 7 0 ! " ,The Install Wizard program starts and the “InstallShield Wizard” screen appears. ) )) 4 + ? 1" 2 '. > A'1 " 0 ! < $ 0! " &$ 9 =;$ 9 =;'/ $ 9 - # / 0 0 $H0 :" Left-click “Next.” <( 1' * 2 / 7' 2 8 " 1 Right-click “My Computer.” 2 Left-click “Properties.” , Installation starts. When installation finishes, a screen indicating that installation has been completed appears. 5 /B (?!- 3 Left-click “Device Manager” in the “System Properties” screen. 9 '. 6 &9 ? L ' $ 1 Double-click “Other Devices.” 1 Select “Yes, I want to restart 2 Check for [ Sony DSC] or [ Sony my computer now.” Handycam] with a question mark. 2 Left-click “Finish.” ) '. ,The computer turns off and then #$ 0 M ';'NM '5 N immediately on again. The USB 7+ ; 8 A'1 " driver is enabled after restarting. # ! "/ $ 0 " 1 E$ ( M ';'NM '5 N" 2 E$ ( 74"8/ 7$;4 8 " 3 E$ ( 7+?8 " 2$ !$ 1 ! <* A'1" )5 )3 1-8

BBBB*6 BBBB*6

, &$ 9 444* # E!0 $ " 9 * < 3 ? 1 - 2 ? 1* 2 / 7' 8 " + ? 1,92 ? 1( - 2 ) + ? 1F 92 1( - 2 ? 1( 6225? 1 ' ('2 1 ! 2 ? 1( 2 To wall outlet (wall socket) 2$ !$ 1 ! <* A'1" 7 ! B '.6 1 # 7:' 8 " '.B8 ?.: 9 2 >0 " 3 / " 7A'1:+;=8 E; $ " Push the connector in as far H $ ;: ! as it will go. 0 0 !J " / ! "1 0 ;: ! 0"

P

#$7A'1:+;=8 $ $ ! 3 MA'1+=/N '=/A2 ! ! ! M+4:>EN$ $$ " 8 '.6 '.B P 7; A'1 $ A'1 6" 7 # 9 7:' 8 $ ! "+ 0 0 !J " Connect to the USB jack on your computer. ∗ / A'1B $$! " )A )>

F96(6? 1- 2

H 0!! ! H0 H0 : 2 ! ! " This “Removable Disk (F:)” indicates the connected

Example: Viewing still images camera.

/ $0!! ! ! " ∗ / & " $$! " 1 9$ 9 ,The “My Computer” folder is 2 ! B '.6 displayed. '.B8 ?.: 9 7 (6? 9 Push the connector in as far as it will go. Double-click the “Removable Disk (F:)” folder. ,The “Removable Disk (F:)” folder contents are displayed. 3 '.6 '.B 8 (6? 1(-2 ,The “DCIM” folder contents are displayed. Connect to the USB jack on your computer. ∗ / A'1B $$! 9 (6? 1<44-'(&2 " ,The “100MSDCF” folder 4 1-' 2 contents are displayed. 9 9 89 : 5 9 7A'1:+;=8 E; $ " ); )= 1-9

BBBB*6 BBBB*6

, 0 (6? Viewing images on Macintosh ,The image is displayed. +'& : +' )"3"C)"C."C.": +'I / +' $ " 50 ! : +' ."C." $ $ 0! " 6 : 0 : +' )"$ ( ! ;(4+: 6 120: G0 : +' )"$ (

Desired file type Double-click in this order / A'1 "

t t Q/<"0 ! "' ! 7;8$ 7 $8$ # !$ :! !L 7: 8$ t 7: 8$ t # !$ L

P

>L 7: 8$ t 7: 8$ t >$ L 7 #$ 0A'1% ! : 7;8$ t 7 $8$ t # !$ % ! $A'1% " ! 7 + ! 0 ! " 7 + ! $ =( ! 7: 8$ t 7#$8$ t # !$ " /# ! '. ∗ ! $ $ $0! "#$ $ $ 7:' 8 ! For Mac OS 9.1, Mac OS X users $$" # A'1"/ : !J ! : 0 A'1 "

For Mac OS 8.5.1/8.6/9.0 users

( 1-( 28: 0 0 " 1 9 -!' 2 (?!- (?!- 3 (6? (?!- 9 9 ,The image data is copied to the “My 4 (6? !' Documents” (example) 9 9 folder. 5 - 999931' &29948 : 7 'A'1; 7 'A'1' 54 5< 6 $ 1* / M2 " 1!I2 1-' 277+ ! $ ! 7:' 8 0 $ 0 $ $ 7:' 8 ! A'1 " 7 ; J 7:' 8 H0 "/ 0

F 9 7:' 8 $"

H 0!! ! : Q/<" 7 ; 7:' "8 $ " " ' 919-!' 7 ;! $ 0 $ J 0 !$ " ! B '.67H!$ ! $ 0 $2 '.B8 ?.: 9 0 $ ! !$ 0 $$ 7#E==44+48 ! 3 '.6 '.B $ " 7 ;! $ 0 $ $ $ : $ " 4 1-' 29989 &$ 9 - $ 9 444 : / $ 0! 0 ! A'1 $ B ! 7:' 8$ 059" 7A'1:+;=8 E; $ " < ' ! 7A !C=B 8 "

H ! $! $ $ 0

6 (6? 9 A'1 B 7:' "8 / $ 7:' 8 " 9 8 $ 9 : 7 ' 6? @ 0 $ !$' ' " &-!'D /$$ $ ! A'1 $ ! 7:' "8 5 5) 1-10

BBBB*6 BBBB*6

,

Image file storage destinations and Folder File Meaning

#:# ;'ssss"@2G 7 ' ( J !$ image files =(:>#E ! 33 ;'ssss"/# 7 A !$ # !$ 0 !$ !" /# ! 3) / ! $ $ $ 0 "ssss $ :+:E :+Dssss":2G 7 :! !$ 0 !$ ..." :+:ED ;'ssss":2G 7 >$ D+#=

For Windows Me users (The drive recognizing the camera is ! 3

“E.”)

P

7 / $ $ 0!$ " T > ( J !$ =(:>#E ! !$ T > !$ /# ! !$ Folder containing still image, TEXT mode image and T > $ D+#= ! !$ Clip Motion image data T > !$ /=I/ ! !$ T > !$ 0 : ! !$ 7; ! $ $ "#$ ! Folder containing E-MAIL mode and TIFF mode $ $ " image data Folder containing moving image data / ! ! ! "/ $ $ $ $ "/ $ 0 Folder containing VOICE mode audio data $ 0 & E*/%

Folder File Meaning : ! ! 0 $ 0

$ "/ $ $ 0 :'; ;'ssss"@2G 7 ' !$ "50$ ! 7 ' !$ !% 0 "/ ! 6 =(:>#E ! 33 ! @2=G$ $ !" 6 /# ! 3) 6 D+#= ! 3 %& 6 1 ! 33 A ! $ !% 0 $ ! E2ssss"G# 7 : $ +4:>E "/ $ $ ! 3. *3 "/ ! ! G#$ E2ssss"/5: 7 # !$ $ : $ : ! 3./=I/ ! 3-" +4:>E && :1Essss"G# 7 : $ :+1#E= ' ! 0 !% ! 3. ": ! $ "/ :1Essss"/5: 7 # !$ $ : $ ! ! /#$ $ /# ! 3)" :+1#E= /I/ssss"G# 7 ' !$ /=I/ -*/% ! 3- / $ $! ! "/ ! :2=G$ $ ! !! D+#= /I/ssss"/5: 7 # !$ $ !$ /=I/ ! 3" 55 53

Advanced operations Before performing advanced -

operations : $$$! $ "/ E; 0 " ! 0 x" / $% $ 0" ! ! )" When the mode dial is set to /

Item Setting Description

' '/ * U*"=D >B "< C<=D =D T*"=D "/ $ ! M=DN" 1 ' '/ * 9 ∞$ ' B ! " / ! )" CAMERA MOVING IMAGE: MPEG MOVIE +A' -" DATE/TIME: OFF RED EYE REDUCTION: OFF <" AF ILLUMINATOR: ON " "3 x>A/+

SELECT

H1 5+E; ' 0 ! <" H5#/= x>A/+ 2 * v@V@b@B691>E #;++4 +A/;++4 3 * z 6 + >B ! $ '2+/ x+ ! 3" :=/=4 ' #'+ ' #'+$ "H ! * ! $ (! B ! ( !"/ 1 ' x>A/+ ! (% ! 0( ! 0 " 2 * -/" x.*O ' ! J0 ! / ! -" #:>G= .*<&* ! ! 3*" '#F= 3 $ # O* 1 2 bCB *)O. 0 "/ ! O) 0" x#= 4 ! $ !% 22z" " DELETE PROTECT PRINT SLIDE • OK '/>;>4; 4 ! ! % " $ # 2 vCVCbCB !$ " / ! 0 400 " 100

AUTO

5A 5> 1-11 .

BBBB*6

,

Item Setting Description When the mode dial is set to (MOVING IMAGE is set to MPEG MOVIE in the SETUP settings.)

:+;= /# 4 /# $ 4= @2=G$ ! 3)" Item Setting Description :+;= /=I/ 4 G#$ ( (0 ! 3-" U*"=D >B "< C<=D =D T*"=D "/ $ ! M=DN" D+#= 4 $ 0 ! @2=G$ ! 3" 9 ∞$ ' B ! " +A' -" =(:>#E 4 ( J<*O*@2=G$ ! J ! 33" <" " 1A4'/* 4 0 ! ! 33" "3 x+4:>E 4 ! ! ! x>A/+ " H1 5+E; ' 0 ! <" P 5#G5 : $ ! " H5#/= x>A/+ E>'5 x+4:>E !" 1>E #;++4 E=D=E +A/;++4 E+H : $ 0 " + >B ! $ 2I '+E>4#F= ' ! $$ ! " '2+/ ! 3" 2"==/ x+1VH :=/=4 '=2#> =G">4/ <*5Q ' :2=G ! J0 ! x+ #:>G= <*O* ! ! ! 3*" '#F= xO* U* >B $ !" U / 0 2I '+E>4#F= ' ! $$ ! " x ! " 2"==/ 1VH T '=2#> T* =G">4/ x+ 5; 5=

When the mode dial is set to (MOVING IMAGE is set to CLIP When the mode dial is set to MOTION in the SETUP settings.) Item Setting Description Item Setting Description ;=E=/= +? ; ! ! -"

U*"=D >B "< C<=D >=E !$ !" =D T*"=D "/ $ ! M=DN" 24+/=/ T 2 ! ! 9 ∞$ ' B ! " ! -*" +A' -" 24#/ T : ! ! -" <" " 'E#;=L ' 0 " "3 x< C3 C C< C x>A/+ 4=2=>/ x+C+ H1 5+E; ' 0 ! <" '/>4/ ' 0" H5#/= x>A/+ 1>E >=E 0"#;++4 +A/;++4 +2, +? ! ! -3" + >B ! $ >=E !$ !" '2+/ x+ ! 3" 4='#F=L .*O ! ! J ! -" :=/=4 O* x+4:>E ' : ! J ! 3." *)O. #:>G= :+1#E= O) '#F= >=E !!$ ! J" P 5#G5 : $ ! " 4+/>/=L 4 !.! ! ." E>'5 x+4:>E !" E=D=E E+H : $ 0 " +? 2I '+E>4#F= ' ! $$ ! " >=E $ !" 2"==/ 1VH ;#D#;=L +? ; ! ! ! -)" '=2#> >=E $ ! !" =G">4/ x+ ∗ + ! ( !" U* >B $ !" U / 0 x ! "

T

T* 34 3< 1-12 . ., / 6 G GG

Setting the image size (IMAGE SIZE) 1-' 28;-.:

' # Quality Image size Usage STANDARD FINE .*O :$! ! >" >"3 .*<&* 2 !<&* >" >"3 O* 2 !>$ >"3 >") *)O. 2 ! J >"** >"* O) > ! ( >") >") - # Image size Usage Number of images or time <*5Q D0!/D >"* " 1 ! <*O* D0! >") " 2 ' O* > ! ( >"<* " :+1#E=*O) T >"< 3 * -/" * $ / " +4:>EO* T >" $ 4 ' H J8-%/'C/:9 b@B 9 v@V ∗ H :+;=4=:+;= +4:>E" ∗∗ / ! !" ' # .*O&*")! !"# .*<&*L / $ ! $$! ! O*&*"! " *)O.&"EO*:+1#E=*O) 3 3)

B Various recording

Recording two Recording still

Recording images A ! images continuously images for e-mail

according to shooting B $ $ (E-MAIL)- # @ conditions (TWILIGHT 0 "50 - # @ mode) / $ ! !" # =(:>#E ( J ! ! " - # / /H#E#G5/ 0 !0 $( ( B 1 / $ ! ! " 5 ! " !"/ J$ ! !M N#:>G= 1 3 '#F= ! ! 3*" 2 2,4 < ' 3* -/" 2,4 < ' / " > 0 ! ) ' H-!(/J8/-!(/: B09b@BH. 'J9 v@V < ' ! $ ! "/ 5 * -/" 0 0 / " * -/" 3 / " !" ) ' H-!(/J8/-!(/:

To return to normal 9 b@BH/?-+J9 v@V

recording mode To cancel the TWILIGHT 5 * -/" ' M+4:>EN0 vCV )" mode / " ' " 3

P

7 , $ " P 7;!! 7 ' $$ 0 ! E; $ /H#E#G5/" ": $ 7, ! ! ! " /H#E#G5/" 7 / ! 7H ! /H#E#G5/ " " > ! *3 ! 0 $ $ $ " 35 33 1-13 . BBBBF, 6 6 1-' 2 Adding audio files to 1-' 2 Recording text 8; -.: /?-+ still images (VOICE) 8; -.: F!/G documents (TEXT) Quality Quality Image size - # @ Image size - # STANDARD FINE STANDARD FINE # D+#= / /=I/ $ .*O >" >" .*O >" >" 3 ! ! .*<&* >" >" !"/ J$ .*<&* >" >" 30J"/ O* >" >" ) ! !M N#:>G= O* >" < >" - E; 0 '#F= ! ! 3*" ! G# >" >" >" >" *)O. *)O. $ " * * 1 . >" >" >" >" 1 O) 5 O) .3 < 3 < 5 ∗ H !3( " !"# 32,4 To return to normal 3 / $ ! $$ recording mode 2,4 ! ! " ' M+4:>EN0 vCV )" To return to normal < ' recording mode < ' ' M+4:>EN0 vCV )" * -/" * -/" / " / " ) ' H-!(/J8/-!(/: ) ' H-!(/J8/-!(/: 9 b@BHF!/J9 v@V 9 b@BH/DJ9 v@V 5 * -/" 5 * -/" / " / " 3361-' 2 $$ " 8; -.: /DG 6 Image size Number of images* $ .*O T) " .*<&* .T* O* *T<) *)O. To return to normal

P

recording mode Recording still Creating Clip Motion 7H M.*<&*N $ ' M+4:>EN0 vCV )" images as ! J ! Files uncompressed files M.*<&*N$ " P (TIFF) 7H ! - # 7 #$ B !" 7 / 7:' 8):1 : $ - # @ !" $$ ! 7H ! ! ! " "/ ! # .*O J !" G#$ 0 $ ! 7H ! ! ! !"/ ! ! ! ( " J$ ! " !M N#:>G='#F= 1,3 7 / ! $ ! ! 3*"/ ! " !% 7,8 7 / $ ! "# ! ! $0MN$ !0 2" QA>E#/, '/>;>4; ! (% !" 2,5,9 #=" 4,6 < ' '/ * / '=/A2 " 3 ' H J8-/:9 2,4 v@VH-!F"%-%/J9 B@v@VH+*-!!"J9 v@V z < ' ) ' * -/" 5 * -/" / " / " ) ' H-!(/J8/-!(/: 3 ' H J8-%/'C/: 9 b@BH&&J9 v@V 9 b@B 9 v@V 5 * -/" / " "!-+8EN0 vCV )" / " 3; 3= 1-14 BBBBF BBBBF, > 6 - 1- Setting the distance Recording images at ' 28;-.: to the subject close range (MACRO) 1/10

Image size Number of images - # @ @ - # @ @

MAKING "CLIP MOTION" >" L $ / ! :+1#E=*O) >" $ ! : ! *3 / " 7:' "8 6 B8 : "/ $ % / $ ! " ) ' H9J8&! ':9

To delete some or all of the 7 / $ J :+1#E= b@B E; "

frame images while making % 9 v@V , B a Clip Motion recording " , $ $ 0! $ 7 G#$ 1 2 b7 $ ! & $ " " >;" >A/+"3 $ ! ) / $ ! < C$ <" . '/NM;=E=/=>EEN0 bC

B z" 3

/ " 3 ' M+?N0 vCV To reactivate auto focusing

P

z" ' M>A/+N0 vCV )" H ! ! H M;=E=/=E>'/N E; "#$ ! 2 P $ ! $ 1 ! 3 $ 0 $$$ ! !" $ $ 0 "A " $ !"

A4 A<

5 * -/"

Adjusting the Adjusting the white / "

exposure B "#$ $ balance (WHITE 3 (EXPOSURE) ! ! 0 BALANCE) 00 B To reactivate auto adjustment - # @ @ "H ! - # @ @ ! B B ' M>A/+N0 vCV )" / B000U0B" 0 ! B0B>A/+"H ! ! 0 ! / ! $$ ! ! 1 0 T" $ $ ! ! "/ ! 5 ! Set the exposure toward + B "5 0 " "50310! B " 2,45B$ ! ! 0 ! 0 3 "< ' 2,4 Set the exposure toward – * -/" / " < ' ) ' H J8/F:9 b@B v@V * -/" >B 0 / " ! ! $ ) ' H$.J8$,/.+: !" 9 b@B , !!$ 9 v@V U*"=D T*"=D $ C< =D" ,!+( 4! ! ( B 5 * -/" ! / " !8" : 3 >B0PA$ ! ! #$ B ! "(!!8n: $ 720! !

B

! % $$ " 7 A ! ! ! ! 7 A ! (!!8 : 4! C ! ! $0

A A)

1-15

BBBBF BBBBF

,

Enjoying picture Recording the date P Using the spot light-

7 #$ M;>/=N ) effects (P. EFFECT) and time on a still ! metering function image (DATE/TIME) 0 7' ! - # @ @ 8 ! 3" - # @ @ - # @ 7 / , ! ! ! ! : A $ 0 $$ " ! " ! 0 ! 1 1,40B55! "2 ! ( ! 0 0 " 3 2,3 1 2,4 4 < ' < ' '/ * / '=/A2 " 2 * -/" ' H J8-/:9 / " v@VH(/@-/J9 B@v@V < ' ) ' H*&DJ8*/&&/:9 B b@B 9 ) ' v@V * -/" 9 v@V / " '!+C/ z / ! ) ' H J8'*!-//: " (0O-/ 9 b@BH!"J9 v@V ' 2 ! ( ! .O$ " 0 0 / " 0 " (/ ' 5 '/* " G / ( !0 ! " !&&

B

; "/% " " / ! $ LCD screen 5 ' ! " !&& 3 ; $$ / $ " E; ! !" / ! Spot light-5 * -/" " metering / " cross hair

To cancel the spot light- To cancel picture effect metering function

' M+N0 vCV )" ' M+N0 vCV )"

A5 A3 B Various playback 7 / ( ! Enlarging a part of a

H ( !

Playing back three or !:=A still image (Zoom and

nine images at once APERTURE VALUE : F2.2 !M24#/NM24+/=/N trimming)SHUTTER SPEED : 1/125 EXPOSURE VALUE : 0.0 M;=E=/=N" CLIP TEXT - # ! --*-"/ - # 100-0005 20017410:30PM :=A ! "/ SINGLE DISPLAY , ! !$ " 1 E; ! / ! 0 J " $ $ 3 1 ( ! 0 PRINT 2,4!$ "/ PROTECTCLIP DELETE TEXT 2 $ vCV" 100-0005 20017410:30PM• OK / $ 0! < ' ! ! ( 6 ! ! " &:! !$ < ' &D+#=$ ) C @ 9 * $6 &=( $ @$6 &2 5 - 9 v@V@b@B / E; ! - &2 $ 0 & /=I/&/=I/$ 7 '! ! ( ! /#&/#$ E#2& : $ To return to the normal size & ! ! 2 z"

To display the next To record an enlarged image

100-0001 20017410:30 (previous) index screen (trimming)

PM

FILE BACK/NEXT VOLUME 2 vCVCbCB" 1 2 :=A $ J!" v 2 ' M/4#::#GN0B7#( ! To return to normal playback z" (single-image) 3 ' ! J0 vCV z" 7 2 J/ " / ! 7 2 z" ! E; CLIP TEXT J $ !"

P

SINGLE DISPLAY H 0! ! : /=I/ ! $$ $ !"

AA A>

1-16

BBBBF BBBBF 6

, To stop the SLIDE SHOW P Playing back still playback Rotating a still image 7, J! ! images in order2zM=I#/N0 B (ROTATE) : ! " (SLIDE) z"7, J ! - # /=I/ " 7 F ! 3O! $ - # To skip to the next/previous , ! ! ! J" image during the SLIDE / $ $ $ ! ! 7 / % $ ! ! SHOW " ! $ " 2Bb" 7 / ! $ " ! !" 1 7 / ! ! 1P0$ " / ! 7 #$ ! ! ! ! J" 7:' 8 0 3,4 " 3,427#$ !7:' 8 2 $$ !" 7, ! J$<&*" < ' 7, /# < ' ! " * -/" * -/" / " / " ) ' H'+(/J9 b@B ) ' H!/J9 b@Bzz' $ 0! 0 vCVC 5 ' H J9 v@V bCB" 9 b@B "/F+ ' H!IJ9 v@V , $ z < < 3 To cancel rotation 3 < < " ' M>=EN0 vCV 5 z" /*/ +&2 ! " P +&>$ ! 7, 0 " ! ! /=I/" 5 ' H'J9 v@V 7, ! z 0 % " / 0 ! " 7> 0 0! ! ! To cancel the SLIDE SHOW $ $ setting ! $ 0 " ' M>=EN0 vCVCbCB ) z"

A; A= B Editing To cancel deleting Viewing images ona72:=A 53 TV screen Deleting images $$"

(DELETE) 7 ' M>=EN0 vCV - # 3" 1$ ! - # $$ /D" , 0 $ " Set the TV/VIDEO switch to “VIDEO.” ? ? 1

W

1 3,4,5 A/V connecting cable W (supplied) 2,4,5 < ' 3 9 $6 to A/V OUT jack < ' * -/" / " ? # ) ' H(/+//J9 b@B < ' ; !0 0 bCB" z @F 5 ' H++JH'/+/J 6 @F! B ? # 2 JH09b@B z @ B ! ( ! 3 $ H++J F ( !"; ' M=/=4N0 bCB #$/D !0 0 z" B ! bCB" > ! $ >CD ! ) * -/" " E B " / " $ H'/+/J ) F 5 ' H(/+//J9 b@B 1' ! 6 ? 9 0 vCVCbCB"/ $ $ / ! /D v@V ? ! !" " z2z!! $$" 3 ' H!IJ9 v@VPztz z 7, /D tz / ! " ( ! ( 7H 0! ! /D ! " !" >4 >< 1-17 BBBBF 6 BBBB/, 4 To release protection $ H'/+/J !! $ ! Preventing accidental2z! 5"/ - 1 ' ! " erasure (PROTECT) " 0 vCVCbCB"/ $ $ ! !" - # To cancel protection2z!! - $$" / $ ! ! 2 :=A 5 " $$" z-tz tz- SET MENU TO NEXT 4 -

P

2 !! $ ! 2 :=A" ! 7:' 8 ! -. 3 "' M+?N0 bCB ! " 1 z" -

W To cancel deleting ? ?

' M>=EN0 bCB 5 3,4,5 M=I#/N0 bCB32z" 1 SET MENU TO NEXT

W < ' 2 2 :=A"

P93' M+?N0 bCB #$ $ 7:' 8 2,4 $6 0 ! ! 3 z" $ $ ! * -/" $ / " To release protection " < ' ) H++J 5#' H*!/J9 b@B ' M+N0 bCB ? z z" ; !0 5 ' H++JH'/+/J H'/+/J 0 bCB" 9 b@B z 5# ? 3 1 ' ! $ H++J 2 JH00vCVCbCB z"' M+N0 bCB ! ( ! " 2 4 1$ ! z ( !" > ! 7: " ; !0 ' 8 " 3 2 :=A 0 bCB" M+?N0 bCB z" ) * -/" To cancel protection / " ' M>=EN0 bCB55' H*!/J9 b@B M=I#/N0 bCB 3 ? 9 z" v@V ? z / ! ( ! ( ! " / - !" > >)

To cancel copying Changing the P Copying images ' M>=EN0 vCV 5

recorded still image 7 / ! ! $ (COPY) z" size (RESIZE) J!"7 , ! J$ ! - # /=I/! - # ! ! , ! : ! " , ! ! J$ 7:' "8 7 / J ! 1 ! ! " 0 $ " 7 #$ J ! ! W 1 7:' 8 0 " 3,4,6 7H !$ J 1 2,5 ! J % 3,4 " 2 7 #$ !7:' 8 < ' $$ 3,4 J !" 297, J ! J$ $6 < ' <&*" * -/" 7H J <&* ! 9 < ' / " 9 9 E; " ) ' H!*0J9 b@B * -/" 7 , J ! z' H' J9 / " ( !" * -/" b@B z / " ) / $ $ !' H/'C/J9 b@B z ) ' H!*0J9 b@B !" z55' 9 ' 9 v@Vz5' H!IJ9 v@V6z.*OO* z *)O.O) 7:=:+4,'/#?>=''82z!! $$" / J ! " " z tz tz 3 $ 1,"%/-/-!0

To cancel changing the size 4 'I2 B

' M>=EN0 vCV 5 !! $ ! 1-' 2 z" "7#'=4/:=:+4,'/#?8 "

A 1-' 2

74=+4;#G8 " H ! 7+:2E=/=8 " SET MENU TO NEXT /! M=I#/N 0 vCV z" 3 * -/" / "

To copy the image to

another “Memory Stick ” ' M+/#A=N0 vCVz3A" >5 >3 1-18

BBBB/ BBBB/

,

A ' H/"/J9 b@B To cancel marking the print A * -/"

z Selecting still images mark / " 7:=:+4,'/#?>=''8 to print (PRINT) 2 :=A 5 > ' H!IJ9 b@B " $$" - # z > $ 1,"%/-/-!0 'I2 B , To unmark selected print 1-' 2 ! 0 " marks 7#'=4/:=:+4,'/#?8 / 0 1 ' ! " ! 30 ; $ 0 ;2+;! 2 1- W z" + " ' 2 74=+4;#G8 "H " 3,4,5,7 To unmark all the print ! ? ? 2,6 marks 7+:2E=/=8 " ' M>EEN0 bCB 5 /! M=I#/N z"' M+N0 bCB 0 vCV z" < ' 1 z" 9

To copy the image to W $6 To cancel marking the print

another “Memory Stick” * -/" mark ' M+/#A=N0 vCV 2,4 / " ' M>=EN0 bCB 5 ; z > 3 ) M=I#/N0 bCB >' H*"J9 b@B ;" z" z

To cancel copying < ' 5 ' H'/+/J9 b@B P

' M>=EN0 bCB ) ? z 7, ! ! M=I#/N0 bCB A ; !0 / $ $ ! : ! ! z" 0 bCB" !" /=I/" H ! 7 #$ !/# ? M>EEN" 0P2JH 0 ! 7, ! " ! ( ! 3 ' 6 @2=G ! 7, ! !! ( !" 9 " 3 :1 "#$7+/=+AG5 ; !06z7#=( :=:+4,8 $ 2 z !! $$" J ! #;=I ! 0 bCB" " ! " ) * -/" z tz 7 #$ M=I#/N $ / " tz 7+:2E=/=8 07:' 8 5 ' H*"J9 b@B 4 ! ! " ? 9 !! $ ! v@V ? " z / ! ( ! ( !"

To unmark the print mark

SET MENU TO NEXT2z! 5"/ >A " >> H"/+J To cancel file division

Dividing a moving / ! ! 2 M=I#/N"/ ! Formatting the

image file (DIVIDE) " “Memory Stick ” " (FORMAT) - # 3 $ P , ! ! H!IJ9 - #'/ * 7 , $ " :2=G:+D#=" v@Vz7/ ! $ " H $ 7:' 8 / 0 A H!IJH"/+J H/DJ 7:' 8 ! 7:' 8 ' To delete unwanted portions 0 " $ 0 !! ! ( of a moving image H!IJ9 v@V z 7:' 8 $$ !" " / ! !$ " W!"X/ 0 > 1$ $ :+D*"!& PNote 1 You cannot divide the / following types of files: 1 ; 0 >" 967: $ 3,4,5,6 7 ' !$ 21AMOV00002.mpg B 37 :! !$ 2 DIVIDE point < The file number changes as ' follows when you divide a 3,4 file. 2 ; 0 1" W!"X#$ MOV00004.mpg * -/" :+D<"!$ $ / " :+D"! 13AMOV00005.mpg B < 1-' 2 :+D3"! 9 ) ' H(F(/J9 b@B z H!IJ :+D<"! "/ DIVIDE point ' '/ * 9 v@V z $ / '=/A2 " / ! ! " $ " ' #( ) ' H J8'/ *<:9 5 * z 1 ; 0 > v@VH&!-J9 B@v@V / $ 0! " 1 2 MOV00003.mpg 1" B 320 5 ' H!IJ9 v@V 1/10 MOV00004.mpg MOV00007.mpgDIVIDE 0:05 DIVIDE point z DIVIDING13AMOV00006.mpg B

POINT

c C To cancel formattingOKCANCEL ' M>=EN0 vCV 5" EXIT DELETE DELETE

OK

MOV00004.mpg 2 + " P HcCJ8 9 : 1 2 MOV00005.mpg 7 7:' 8 ! ", $ , $ B13MOV00006.mpg 7:' 8 ! !bCB" Divided at the designated point A'1 " 7H $ $ ! >0 0 " >; >= 1-19

BBBB/ BBBB/

,

SETUP 2 Changing the setup settings (SETUP) Item Setting Description

/ '=/A2 ! ! $$% ( " E; 14#G5/ ' E; ! " ' '=/A2"/ '=/A2 ", 14#G5/='' x+4:>E / $$ ! " $ 0! 0 " ! 0 x" ;>4? E; 14#G5/ ; 0 !

CAMERA 1>?E#G5/ x+4:>E 0 & Item Setting Description ' ! $ E; ! "

' !M14#G5/N :+D#G x:2=G:+D#= 4 :2=G$ ! *" ! 0 ! #:>G= E#2:+/#+ 4 : $ ! 3." ! ;>/=C/#:= ;>,V/#:= ' 0 !$ " ;>/= ! ! " 1==2 '5A//=4 / "/ x+ 0 " 4=;=,= + 4 ( ! *" 4=;A/#+ x+ x+ / C0C" > x+ A 0 $$ $ #EEA:#>/+4 + B ! *3" + / $$ C " D#;=++A/ /' ' ! /'

SETUP 1 "!"@ A'> ! )3" Item Setting Description 2>E ' ! 2>E

"!"= ! )3" +4:>/ +? & 1-' 2 " A'1+=/ 2/2 '0 A'1 ! <" 1- x+4:>EA0$ '0 ' 2 0 2/2 " 2+H=4'>D= + ; 0 ! >=E $ !$ 7:' "8 x+ 0 & ' M+N $" #E=A:1=4 x'=4#=' > ! $ %$ 7:' 8 !" H M2+H=4'>D=N M+N $0 4='=/ 4 $ ! ! ! 7:' 8 !" ! *" C x=GE#'5 ; =! " ;=:+ x+C'/1, ; 0 E>GA>G= C@2 ; @ " + 0 >0 "M;=:+N M'/1,N $ E+?'=/ +? ' 2$ $ >=E $ 3 ! 3" "/ $$ 0" $%&'( ') 7 / E; ! !"/ ! " 7 / ! ! : ! " ;4 ;<

Additional information ,9 ! 6

On “Memory Sticks ”

Precautions H !! $ 7 A $ !0

0 !!$ " 7:' 8 0 ! 0 7 / $ #!0 ! 0 $ 0 B $ " " 0 " 7:' 8 !$ +( 7 ? 0 $$" !! !! ! H $ 0 ! 7 7:' 8 " E; ! /$$ 0 1 7:' 8 $! $ " $ $ !" " 0 ! " ! 0 7 ? " / 0 $7:' 8& ! " 7; ! 7:' 8 7: !G $ 0 $ " :' 8 %0 ! 000! 9 7; $ : !G L! $ "; $ " !"

J

7 / $ > 7 # , $7:' 8 ! $ !" 0 ! " 0 "5000$ 7 !!0 : !G $ $$" $$ ! 7 A ! $ 0 0 " B : !G ! $ "+ 0 " $ ! 0 ! $ ! " #$ ! $ ∗ : !G ! ! $ " 7 / 0 ' " ! !" !" 0 $" " 7; 0 ! ! 6 7:' 8 7: !G 0 $ 6 6 :' 8 $ !" ' " , !$ 0 7; 0 / ! 7: !G 8 $ <* $ B "/ $ ! $' " "4! 0 ! ! ! $ ! $ " 0 0 $$"/ " 72B$! ! 0 $ ! ! ! " ! "#$ 50$ $ ! !" ! ! $ 7 > 0 " $ #$ ! $ 7; " 7; !"# ! " ! $ ! "' 7H ! " 0 " !! 0 $>: 50$ ! - % ">: ! 0 " ! 9 # 7 / ! $ 7 / 0 ! "/ " 0 $ " " 7; & 007/ $ ( 6= 0 >0 6; ! " 6D $* 0 6D ! 2+H=4 +" ; ;) 1-20

BBBB/

, $ !"#$ ! ,9 6 "' P $ #$ $ ! 1 # 1 7; !$& ! $$ $ 0! > 6 7:' 8 ! " $ " = @ @ ? $$ 0 ! 7 >$ !! " ! " :2' / 0 0 ! " >0 $ ;#B *" ; ! " 6 7:' 8 2 A"'">"DJ " <" 4 $ B $$ $ " " *+ " 7H ! > > 1 ! 7; 75#8 E; . ! 7 / $ "1 ; G G " !"50 $ 1 5 5!?!# 7> 0 "H "H ?0 : 0F $ " 75#8 ! 0 2 ! '! ' 7H 7: !! " '0'0 J / " ' 8 " $ $" 7 / 6 ; $ 2 0 " *+?- 7:' 8071$ 0( 7 / $ ! 01JB" ! "' ! 7; $ " *+?" 7:' "8 "H $ 0! >! 2 ! A! 7; $ ! & '/- 7:' "8627; 0 7:' 8 ! 0 Using your camera 1 ! J40" $ abroad G 5! # # %: !" 2 4 ' 4 7 % ! E; 0 $ " *9 A " 7 1 $$ 00 ,

On “InfoLITHIUM” ! ! 0

battery pack " !0 D *D 7H ! >3C5J"A $ 0 > ! HJ$ ! ! ! !$ $ ! " 0 0 H6J" 7; 0 " $ 1 +, -26 / 0 ( "

M

/ 7#$E#/5#A:8 6 ( $ #$ 0! $$ ! $ !$ ! ! $ " ! 0 / 7#$E#/5#A:8 ! $ ! $ 6 0 ! ! F ! $ " 0 #$0 0 ! 0 /D /D ! " $ ! B $ ! $ $ 6 ! " ! 7 1 ! $ / $ /D $% "4! ! ! " $! 7H !! ! " " $ 0! & $ 0 <3 ) 7 8 ! ;5 ;3

Troubleshooting Symptom Cause and/or Solution

/ $$ " 7 , !0 #$ 0 $ $ 0! "' B $ *< 3C) $ " 4='=/ "#$ 4='=/ ! ! t' ! ! " "' ' 7 / $ " J' $ " ssss t $ ! " !" / J!$ 7 , J! ! ! 0" : ! "

Symptom Cause and/or Solution # ! /=I/ 7 E! ! B "

" t t>B ! ! B / 0202+H=4 $ " 0 " 2+H=4 " , ! 7 / " /=I/" , 7 , ! 7#$E#/5#A:8 " t' " 0" tA 7#$E#/5#A:8 ! " , 7 , ! ! 7 / 0 E " ! : ! " E; " / " 7 , /D t ! ! " % ! ! " 7 / >0 " t: 0 $ /D " t $ ;#B $ / " 7 , ! B 0 ! 0 0 ! B " " 7 t>B ! *"/ ( 0! " t 7 / ! $ E; 0"; 0 $ "/ 0 t>B ! $ E; 0 " ! )" 2 4='=/ ! ( / ! " 7 , ! ! B B " !" , 7 , ! 0 !! $ " t>B ! *" ! " 7 / '=/A2" 7 / E; ! " t' ! .*" t>B ! $ E; 7 7:' 8 ! )" " / $ 0" 7 / $ $ " t# 7:' 8 ! -" t' $ $ 7 / 0 7: $ ! *" ' 8 E+?" 7 / " t' ! " t' $ $$ " / E; 7 / 00 $$0 E; 7 / '=/A2 :2=G ! 0 0 + 0 " :+D#=" " t/ ! $ t' " 0 "#$ 0$$0 7 M:+;=N4=:+;= M1A4'/*N E; + E; ! " + 0" t' " ;A ;> 1-21, Symptom Cause and/or Solution Symptom Cause and/or Solution / 7 / " " t / ! 7 , ! $ $ ' ! 3" 0 7:' "8D7/ !" ! t $ $ 0 ! t/ $ " " $ $ ! B " ! " / $ " 7 , !C ! ! / ! t $ 0 $ " " 7 / !! " " t ! $ " , 7 / ! " 7 / " !" t ! -*" t400! )3" / 0 $$ 7 / (0$$$ ! * " " t/ >0 / ! 7 , $ ! " " " 7 / !" 7 / " t4 0 ! " t400! )3" / ! 7 / ! !$ 7 / !" /D " " t# ! ! " t ! ! ! )" '$$ 7 > ! >$ 0 7 , $ 0 ! ! " $ " J ! .*O00t" ! ! " " / 7 / /=I/" / $ 7 / " t /=I/ ! 3-" ! !!" t# ! " 0 " 7 2"==/ 1VH" 7 / $ " t 1VH ! " t ' J ' $ " , ! 7 / " ! t/ $$ ! " 00 7 / >0 " ! !!" t000! " ;! J 7 / ! J 0 ! $ " ! !0 M:+D#G#:>G=N M:2=G:+D#=N E; +" , 7 / '=/A2" ! " t' ! *)*." 7 , !$ $ $ $ ! ! $" ;; ;= Symptom Cause and/or Solution Warning and notice messages , 7 / 0" !J " tA >0 ! " D ! E; " ! 7 / $$" $ 0! " t/ " 7 / A'1 $ " Message Meaning t; A'1 ! +:=:+4,'/#? 7:' 8 " $ ": 7A'1:+;=8 E; ! <-<)" ','/=:=44+4 / 0$$ ! " 7 MA'1+=/N M2/2N ! " :=:+4,'/#?=44+4 7 / 7:' 8 t' M+4:>EN ! )" 0 7 / A'1 !" % 7 / 7:' 8 " " t; A'1 $ +4:>/=44+4 $ 7:' "8 :=:+4,'/#?E+?=; / 0 ( 7: " ' 8 E+? " 7 / A'1 " t# A'1 ! <*" +:=:+4,'2>= / $ 7:' 8 7 ' 0 $ A'1 $ ! A'1 ! " !J " +#E= ! t; 0 !J 7:' "8 A'1" #E==44+4 >0 ! ! <3" !" $ 0 ! t4 ! #E=24+/=/ / ! ! " 0 " $ "#$ $ 0 4='=/ ! . $7#$E#/5#A:8 / 7#$E#/5#A:8 ! ( B "#$ " 4='=/ ! ! +/=+AG5:=:+4, / ! 0 ! " 0 " +2,=44+4 !0 $ 7:' 80 ! !" ;#4=/+4,=44+4 > 0 7:' "8 #:>G='#F=+D=4 , ! !$ J " #D>E#;+2=4>/#+ , ! $ 0 % " =4 =< 1-22, Message Meaning Self-diagnosis display E / 0" ;! $ , $( ! "/ $ $ $ ! 3 E; 0 $ C:32:ss $ ! $! $ "#$ $ " $ 0! "/ $ $ >+/;#D#;= Y / $ !! 9 "/ 0! " ss0 $$! Y / $ ! !" $ " / $ ! $$ # 0": 7 &ss&ss 0 , " $ $" 7 =&ss&ss E='+D=4E+'=; / " ' /A4/5=2+H=4+>;+ / 0 " J' $ " >G># First three digits Cause and/or Corrective Action &<*&ss 7 / 090" t/ 0$$ ! " &<&ss 7 / 0 7:' "8 t4( 7:' 8 " 7 >$ 7:' 8 " t 7:' 8 ! -." 7 / 7:' 8 0 !" t# 07:' 8 ! -" =&&ss 7 > $ =&.&ss " t ' J ' $ $ $ 3( ! &=&&" 6 6 /'/6 ' ' = =)

Display window indicators LCD screen indicators

8 90qaqsqd qf512qg63qh 4 + qj 5 qk 6 ql A ' ? E 1-' 2 7 w; B - F 6 wa C & 8P=== === D . :@. 6 A . M686@ :@- B & @ @ ' ? 9 6 @& 6 / $ ! C ( @ @'! 6 ! $$! ! " D ' N E * F & O - @ 9 @& G ' ? P /F H /@&

Q I

R '

J

S ' ? KLT+ 9 L $+%, U - 2 !:=A 0 C$$" =3 =A 1-23, $ 6 456745617120min 640 1 11/12min 2 STBY82x1.3 3 SOLARIZE 9 + qa38FILE BACK/NEXT VOLUME EV WB qs A * @ F 6@ 6 1- A . GBC' 2 B $ 6 C & GCH- @ 9* D @& DEH6I /F @

E

J ' ? FHK' ? 6 J @ $ 6 ' ? L - 2 !:=A 0 C$$" 234560min 320 1 6/80:12 6 DELETE PROTECT PRINT SLIDE 9

OK

A F!+8F: FBG*6CH*6 D 6@ 6 I - 1- ' 2

E

=> =; 11-2-244 E,

SECTION 2 DISASSEMBLY

• This set can be disassembled in the order shown below. 2-1. BT LID DSC-P3 (Page 2-2) 2-2. CABINET (FRONT) 2-3. CABINET (REAR) 2-4. LCD MODULE ASSEMBLY (Page 2-2) ASSEMBLY (Page 2-2) (Page 2-3) 2-6. MODE DIAL BLOCK 2-7. CABINET (BOTTOM) 2-5. LENS BLOCK ASSEMBLY SERVICE POSITION ASSEMBLY (Page 2-4) ASSEMBLY (Page 2-4) (Page 2-3) (SY-73 BOARD: side A) (Page 2-3) 2-8. SY-73 BOARD (Page 2-4) 2-9. MEMORY STICK 2-10. ST-67 BOARD CONNECTOR (Page 2-4) (Page 2-5) 2-11. DD-163 BOARD (Page 2-5) SERVICE POSITION (SY-73 BOARD: side B) (Page 2-5) 2-1, Note: Follow the disassembly procedure in the numerical order given. 2-1. BT LID When removing the BT lid, destroy and do it. When two claws of the BT main frame assembly have bent, it becomes not possible to use. Two claws of the BT main frame assembly

NG

2-2. CABINET (FRONT) ASSEMBLY 2-3. CABINET (REAR) ASSEMBLY 2 Screw 1 Screw 2 Screw (M1.7) (M1.7) 4 Cabinet (rear)(M1.7) assembly 1 Screw (M1.7) 3 Two screws 3 Two screws 4 Cabinet (front) (M1.7) (M1.7) assembly 2-2, 2-4. LCD MODULE 2-5. LENS BLOCK ASSEMBLY 4 Light interception sheet (LCD) 3 Pull the flexible board in the direction 1 Flexible board of the arrow, and it removes while lifting (CN952) LCD (charactor display). 7 LCD module (Because a both side tape is pasted) 4 Two step screws Flexible board (M1.7) 2 2 Claw (CN953) 3 Two screws (M1.7) 5 Four claws 6 Back light unit 5 Two cushion (L) 6 Lens block assembly 1 Three flexible boards (CN101, 201, 954) [SERVICE POSITION (SY-73 BOARD: side A)] Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Adjusting remote Note 3: Fastening the hook of the LENS COVER OPEN/ commander CLOSE switch (S201) on the SW-364 board with tape. SY-73 board CPC-9 jig Lens block assembly (J-6082-393-C) 1 18 1 SW-364 board Colour monitor Regulated power supply (6.0 to 7.2 Vdc) Base LCD module S201 Back light unit AC power AC IN adaptor 2-3, 2-6. MODE DIAL BLOCK ASSEMBLY 2-8. SY-73 BOARD 3 Mode dial block assembly 7 Flexible board (CN501) 1 Claw 2 Boss 1 Connector (CN102) 4 Connector (CN906) 5 Flexible board (CN905) 4 Screw (M1.7 × 4) 6 SY-73 board 5 Claw 2 Connector (CN901) 3 Four flexible boards (CN101, 201, 904, 954) 2-7. CABINET (BOTTOM) ASSEMBLY 2-9. MEMORY STICK CONNECTOR 1 Claw 1 Two screws (M1.7 × 3) 2 Claw 3 Memory stick connector 2 Cabinet (bottom) assembly 2-4, 2-10. ST-67 BOARD 2-11. DD-163 BOARD 2 ST-67 board 5 Sdhesive sheet (LCD) 6 Two screws (M1.7 × 4) 8 DD-163 board 7 Claw 1 Screw (M1.7 × 4) 3 DD sheet metal 2 Claw 1 Screw (M1.7 × 4) 4 Screw (M1.7) [SERVICE POSITION (SY-73 BOARD: side B)] Adjusting remote commander Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate CPC-9 jig the adjustment remote commander. (J-6082-393-C) Note 3: Fastening the hook of the LENS COVER OPEN/ CLOSE switch (S201) on the SW-364 board with tape. Regulated power supply (6.0 to 7.2 Vdc) DD-163 board LCD module Back light unit SY-73 board AC power adaptor AC IN ST-67 board Colour monitor Mode dial block assembly Base Lens block assembly Memory stick connector SW-364 board S201 2-5, 2-12. CIRCUIT BOARDS LOCATION DD-163 CONTROL SWITCH, BACK LIGHT DRIVE, DC/DC CONVERTER, JACK ST-67 (FLASH DRIVE) CD-340 (CCD IMAGER) SY-73 CAMERA PROCESS, CAMERA DSP, ( VIDEO, MEMORY, LENS DRIVE, SH DSP, USB I/F, FRONT CONTROL, AUDIO, LCD DRIVE, TIMING GENERATOR,) FLASH CONTROL, REGULATOR 2-6 E,

SECTION 3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM

SY-73 BOARD CD-340 BOARD MIC901CAM SO, XCAM SCK MIC SIG

LENS (Included in the LENS BLOCK ASSY)

MICROPHONE IRIS METER

IC102 DD-163 BOARD (2/2)IC501 Y OUT Y OUT CCD OUT CCD S/H, AGC, DATA BUS 14 C OUT IC601 J651 C OUT V OUT A/D CONV. AV OUTIMAGER V OUT ON VIDEO AMP (SEE PAGE 4-10) (SEE PAGE 4-15) (SEE PAGE 4-20) A OUT (MONO) PANEL Y IC301 PANEL R-Y CAMERA PANEL B-Y

FOCUS

MOTOR H1, H2 IC101 DSP (SEE PAGE 4-17) LENS V1A, V1B, V2, TIMING IC251 TEMPMHMV3A, V3B, V4, VSUB CONT GENERATOR AU SDTO REC OUT SENSOR (SEE PAGE 4-15) AUDIO AD/DA CONVERTER IC252AU SDTI PB IN (SEE PAGE 4-29) AUDIO AMP SP+, SP– SP901 (SEE PAGE 4-29) FOCUS SPEAKER IC201 (1/2) SP VOLRESET SENSOR DATA BUS 16DRIVE+ IRIS MSHUT ON IC302 BEEP (MECHA SHUTTER) 128M SDRAM DRIVE ADDRESS BUS 14 (SEE PAGE 4-19) IC202, 203 (SEE PAGE 4-21) (SEE PAGE 4-21, 22) PANELYRDRIVE– IRIS CONT1,2 PANEL R-Y IC801 G LCD901IRIS DRIVE CAM SI, CAM SO, XCAM SCK PANEL B-Y LCD B HALL REF DRIVE HALL + HALL GAIN (SEE PAGE 4-31) 1.5 inch HALL AMP SP VOL IC804 COLORHALL AD V OUT LCD PE DAC LEVEL1, 2 IC506 IC503 ON IC802 LCD TIMING UNIT CNT C EVR EEPROM EVR GENERATOR FOCUS RST XFC RST SENS IRIS CONT1,2, (D/A CONVERTER) (SEE PAGE 4-25) (D/A CONVERTER) (SEE PAGE 4-32) HALLREF, HALL GAIN (SEE PAGE 4-25) (SEE PAGE 4-31) BL LEV IC201 (2/2) PE EN0, FOCUS PE DIR0A, PE DIR0B DRIVE 16 16 D901 IC951 Q951 – 954 BACK LIGHT(SEE PAGE 4-21) IC501 BACK LIGHT BACK LIGHT STRB ON 14 20 CONTROL DRIVE TEMP OUT LENS TEMP AD STRB AIN MC CAM,SH DSP (SEE PAGE 4-48) (SEE PAGE 4-23) 16 BL ON IC504

ST-67 BOARD 16M

(SEE PAGE 4-41) FLASH 20 T001 (SEE PAGE 4-26) D+ D+ IC701 CN652 USB DATA USB I/F CHARGING D– D–

USB

CAPACITOR ST UN REG (SEE PAGE 4-26) FLASH STB CHG IC505 UNIT STB FULL XSTB FULL 64M SDRAM FP-380 FLEXIBLE (SEE PAGE 4-25) 14 (SEE PAGE 4-37) Q011 DIO, BS, SCLK MS

SOCKET

STB ON1 STRB ON HALL AD Q012 LENS TEMP AD BRIGHT PHOTO TR OUT STRB AIN LEVEL HI SI, HI SO, XHI SCK LCD DD ON

DD-163 BOARD (1/2) SENSOR

STB CHG BEEP XSTB FULL BATT SIG LCD902 SYS DD ON SYS DD ON COM 1 – 4 COM 0 – 3

LCD MODULE

CHARACTER SEG 1 – 9 SEG 0 – 8 UNREG SO, UNREG SCK UNREG SO, UNREG SCK IC401 DISPLAY KEY AD 3

FRONT

KEY AD 0, 1 XRESET CONTROL HI UNREG IC402 IC001(SEE PAGE 4-28) D 1.8V D 3.2V DC/DCINITIAL CONTROL VL 3V RESET, A 3.2VBT101 (SEE PAGE 4-49)BACK UP VCC BACK UP VCC PANEL 3.2V LITHIUM +D401 (SEE PAGE 4-28) EVER 3.2V BATTERY 3.2VCONTROL SWITCH BLOCK BATT SIG BT901 (BACK UP) A 4.9V S (SEE PAGE 4-37) BATTERYM 5V TERMINAL XPWR ON CAM 15V – XPB ON, XSET UP, MODE DIAL, XMOVIE BL VO– XAE LOCK SW, XSHTR SW

SW-364 BOARD J652ACV UNREG

(SEE PAGE 4-38) DC IN LENS COVER XLENS CAP OPN SHUTTER MODE POWER FUNCTION ZOOM ST UNREG OPEN/CLOSE SWITCH DIAL ON/OFF KEY SWITCH BATT UNREG HI UNREG 3-1 3-2 CAM SO, XCAM SCK ADDERESS BUS DATA BUS KEY AD 0, 1 KEY AD3, 3-8. POWER BLOCK DIAGRAM 1

DD-163 BOARD SY-73 BOARD (1/2)

F001 CN951 CN901 J652 BATT UNREG BATT UNREG BATT UNREG34 34 DC IN F002 ACV UNREG1 ST UNREG 41 ST UNREG 41 ST UNREG 43 43 BATT/XEXT BATT/XEXT F003 45 45 ACV UNREG ACV UNREG ACV UNREG 36 36 F004 D009 IC001 Q017, 018 FAST CHARGE IC002 DC/DC CONTROL D007 D006 Q015, 016 (SEE PAGE 4-50)(SEE PAGE 4-49) L016 L017 D001 DC/DC HI UNREG HI UNREG INIT CHARGE CONVERTER 35 35 BT901 D010 BATTERY VCC2 41 TERMINAL D008 L019 Q002, 005 L005 L011 BATT UNREG1 SWITCHING 29 D 1.8V 29 D 1.8V+ BATT SIG BATT SIG D953 30 30

S

OUT 3p 32 D952 (AE/AF LOCK) D954 – SYS DD ON OUT 3n 33 (FLASH) (SELF TIMER/REC)57 CONT VIN 3– 54 XCS DDCON 44 XCS UNREG SO VCC3 42 L020 Q003, 006 L00645 L007DATA UNREG SCK VCC5 20 SWITCHING8D3.2V8D3.2V 46 CLK 10 10 L008 OUT 4p 307A3.2V7A3.2V9947 RST OUT 4n 31 L009 Q808, 810 PANEL 3.2V PANEL 3.2V 48 LD ON VIN 4– 53 27 27 56 VCC1 L021 EVER 3.2V 58 CH2UP L004 Q008, 010 Q012 L012 SWITCHING A 4.9V A 4.9V37 37 OUT 5p 38 OUT 5n 39 OUT 5S 43 VIN 5– 52

TO A POWER BLOCK 2

L002 Q009, 011 Q013 L013 25 25 (SEE PAGE 3-17) SWITCHING M 5V M 5V26 26 28 28 OUT 6p 28 OUT 6n 29 OUT 6S 18 VIN 6– 50 L001 Q007 D002 D003 L014 SWITCHING CAM 15V CAM 15V1 1 Q954, 955 OUT 9 23 L951 L801PANEL 13.5V PANEL 13.5V

REG

IN 9– 80 SCP91Q9513.2V33Q004 Q952, 953D004 D005 L010 BL VO– VCC4 19 SWITCHING CAM –7.5V CAM –7.5V11 11 REG OUT 10 22 AMP IN– 4 AMP OUT 5 IN 10– 3 Q001 SCPIN 10 EMERGENCY CAM –7.5V DETECT 39 39 LCD DD ON PANEL UNIT EVER 3.2V EVER 3.2V EVER 3.2V 33 33 SYS DD ON SYS DD ON SYS DD ON22D901 CN953 FAST CHARGE FAST CHARGE FAST CHARGE50 50 BACK LIGHT BL L INIT CHARGE INIT CHARGE INIT CHARGE1 48 48 PANEL 3.2V XCS DDCON XCS DDCON XCS DDCON666UNREG SO UNREG SO UNREG SO55IC951 UNREG SCK UNREG SCK UNREG SCK4 4 BATT/XEXT BATT/XEXT BATT/XEXT LCD901 BACK LIGHT 76 76 CONTROL BATT SIG BATT SIG BATT SIG53 53 CN952 (SEE PAGE 4-48) 1.5 inch D803VDDG COLOR 16 VDDG 70 70 LCD VDD VDD18 71 71

UNIT

3-15 3-16, 3-9. POWER BLOCK DIAGRAM 2

ST-67 BOARD SY-73 BOARD (2/2)

(SEE PAGE 4-41) T001 CN102 CN903 FLASH 23 ST UNREG 23 Q910, 921 UNIT 25 2527 27 D101 SELF TIMER/ 1 PRELAMP POWER 1 IC401 AF ILLUMINATOR FRONT CONTROL (SEE PAGE 4-28) BT101 VL 3V LITHIUM BATTERY 29 29 35 STB CHG (BACK UP) Q102 – 105 CD-340 BOARDIC402 FB113 CN101L104 (Included in the LENS BLOCK ASSY) INITIAL RESET, BACK UP VCC IC501 CAM 15V CAM 15V 6 (SEE PAGE 4-28) MC CAM, L401 SH DSP CAM –7.5V CAM –7.5V73VBAT VOUT 6 BACKUP VCC (SEE PAGE 4-23) FB112 8 VRO CS 4 26 (BATT IN) CAM DD ON 17 ST UNREG IC50115 BATT IN MS POWER ON 15 A 4.9V HI UNREG CCD7 VIN RESET56XRESET L101 IMAGERA 3.2V D301 (SEE PAGE 4-10)EVER 3.2V SYS DD ON LCD POWER 1631 SYS DD ON FAST CHARGE 37 FAST CHARGE VOUT ON 24 L102 FB110 FB111 INIT CHARGE 36 INIT CHARGE 20 LCD DD ON D302 XCS DDCON 27 INIT CHARGE UNREG SO 28 INIT CHARGE UNREG SCK IC102 IC10129 INIT CHARGE BATT/XEXT D502 S/H, AGC, TIMING14 BATT/XEXT (ACCESS LED) Q403 A/D CONV. GENERATOR (SEE PAGE 4-15) (SEE PAGE 4-15) BATT SIG BATTERY 78 BATT SICHARGE DETECTOR 79 BATT SO BATT UNREG 93 BATT SENS ACV UNREG IC502 IC503 IC505 IC504 94 ACV SENS D 1.8V BUFFER EEPROM 64M 16M92 DD CON SENS CONTROL SWITCH(SEE PAGE 4-24) (SEE PAGE 4-25) SDRAM FLASH (SEE PAGE 4-25) (SEE PAGE 4-26) BLOCK LCD DD ON (SEE PAGE 4-37) S005 CN905 D 3.2V 6 MODE

DIAL

TO IC252 IC251 IC301 IC302 Q304, 306, IC506 FB502 FB503 POWER BLOCK1AAUDIO AMP AUDIO AD/DA CAMERA 128M SDRAM 308 – 3011 EVR(SEE PAGE 3-16) (SEE PAGE 4-29) CONVERTER DSP (SEE PAGE 4-19) BUFFER (D/A CONV.) (SEE PAGE 4-29) (SEE PAGE 4-17) (SEE PAGE 4-20) (SEE PAGE 4-25) PWR LED VCC D0014 (POWER) L301 FB303 L305 L502 L254 L253 L252 L302 FB301 L306 L503 D 1.8V D 1.8V FP-380

FLEXIBLE (MS SOCKET)A 4.9V A 4.9V

A 3.2V A 3.2V CN501 (SEE PAGE 4-37) 1Q502 D 3.2V D 3.2V D 3.2V VCC2268CAM 15V CAM – 7.5V L203 L202 LENS BLOCK CN201 Q203 D 3.2V 4 SENS VCC FOCUS RESET M 5V M 5V 5 SENSOR PANEL 3.2V L802 PANEL 13.5V FB601 L601 L201 L803 IC804 IC803 IC801 IC802 IC701 IC601 IC203 IC202 IC201 LCD TIMING VREF AMP, LCD EVR USB I/F VIDEO AMP IRIS DRIVE IRIS DRIVE FOCUS/ GENERATOR VCO DRIVE (D/A CONV.) (SEE PAGE 4-26) (SEE PAGE 4-20) HALL AMP (SEE PAGE 4-21) IRIS (SEE PAGE 4-32) (SEE PAGE 4-32) (SEE PAGE 4-31) (SEE PAGE 4-31) HALL BIAS/GAIN (MECHA SHUTTER) CONTROL DRIVE (SEE PAGE 4-22) (SEE PAGE 4-21) 3-17 3-18 E D401 L251 L303 FB302 L504 Q305, 307 FB102,

SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) • b: Pattern from the side which enables seeing. • Voltages and waveforms are measured between the (The other layers’ patterns are not indicated) measurement points and ground when camera shoots • Through hole is omitted. color bar chart of pattern box. They are reference values • Circled numbers refer to waveforms. and reference waveforms. * • There are a few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used) isn’t mounted in this model. • Voltage values change depending upon input impedance • Chip parts. of VOM used.) Transistor DiodeC6544564512333431. ConnectionBE12332132154321212112Pattern box5421341234123345214321(For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ L µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. Front of the lens New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. L = About 30 cm Example C541 L452 22U 10UH TA A 2520 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. Kinds of capacitor H Temperature characteristics External dimensions (mm) • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. A B A=BBA• All variable and adjustable resistors have characteristic Fig. a (Video output terminal output waveform) curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC Color bar chart • 2: non flammable resistor picture frame • 5: fusible resistor Monitor TV • C: panel designation picture frame • A: B+ Line * • B: B– Line * • J : IN/OUT direction of (+,–) B LINE. * • C: adjustment for repair. * Fig.b (Picture on monitor TV) • Circled numbers refer to waveforms. * * Indicated by the color red. When indicating parts by reference number, please include the board name. Note : The components identified by mark 0 or Note : Les composants identifiés par une marque dotted line with mark 0 are critical for safety. 0 sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifie. 4-1 Yellow Cyan Green Yellow White Cyan Magenta Green Red White Blue Magenta Red Blue, 4-1. FRAME SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM (1/2)

12345678910 11 12 13

FRAME(1/2) A

LCD902 Q012 LCD MODULE BRIGHT LEVEL (CHARACTER DISPLAY) CONTROL SWITCH BLOCK SENSOR D101 SELF TIMER/ AF ILLUMINATOR(RED) S005

B FLASH UNIT MODE DIAL

9182710 C00863POWER (CHARGING CAPACITOR) ON/OFF(CHG) 5 4 S004

C

BT101 ST-67 BOARD S00312LITHIUM BATTERY (BACK UP) 3 4 (SHUTTER) D001

D (POWER(GREEN))

CN102 30P CN501 8P 8 VSS

E FP-380 7 BS6 VCC MS 5 DIO

4 INT

SOCKET FLEXIBLE 3 SCLK BOARD 2 VCC

1 VSS

F

CN902 18P 1 BL_L1 2 N.C CN903 30P

G 3 N.C

4 REG_GND 5 CPC_IN 6 BL_L2 7 HSY 8 PANEL_COM

CPC

9 VG (FOR CHECK) 10 HI_UNREG RESET

H 11 LANC_IN S401

12 LANC_OUT 13 MAKER_RECOG 14 N.C 15 N.C 16 N.C SY-73 BOARD(1/2) D502 17 N.C (ACCESS LED(RED)) 18 N.C

I SW-364 BOARD CN954 6P

S201 1 NC LENS COVER 2 GND OPEN/CLOSE 3 GND 4 XLENS_CAP_OPN

J 5 XLENS_CAP_OPN

6 NC CN906 2P MIC901 2 MIC_SIG MICRO PHONE

K 1 REG_GND FRAME (1/2)

4-3 4-4 2 XPRELAMP_AF_ON PRELAMP_POWER14SEG1 COM436SEG2 COM358SEG3 COM2 7 10 SEG4 COM1 9 12 SEG6 SEG9 11 14 SEG5 SEG8 13 16 REG_GND SEG7 15 18 REG_GND REG_GND 17 20 REG_GND REG_GND 19 22 REG_GND STB_FULL 21 24 REG_GND ST_UNREG 23 26 PHOTO_TR_C ST_UNREG 25 28 PHOTO_TR_OUT ST_UNREG 27 30 STB_ON1 VL_3V 29 CN905 14P XPWR_ON 1 XPWR_LED 2 NC 3 PWR_LED_VCC 4 MODE_DIAL 5 D_3.2V 6 NC 7 GND 8 NC 9 XPB_ON 10 XMOVIE 11 XSET_UP 12 XSHTR_SW 13 XAE_LOCK_SW 14,

FRAME SCHEMATIC DIAGRAM (2/2)

12345678910 11 12 13 14 15

FRAME(2/2) LENS UNIT A OPTICAL VIEW FINDER LENS B C CD-340 D BOARD

(INCLUDED IN THE LENS UNIT)

E F SY-73 BOARD(2/2)

CN901 80P

G H I CN951 80P

CN652 5P VCC 1 D- 2 CN952 USB D+ 3 SP901 1 TESTR ID 4 SPEAKER

J 2 RGT GND 5

3B4RJ6525GDD-163 BOARD DC IN 6 PSIG D952 7 HCK1 (FLASH(AMBER)) J651 8 HCK2 ZOOM A/V OUT 9 CRext S952 S953 (MONO)

K PANEL UNIT 10 SDUT (N.C) W T

11 REF 12 HST 13 WIDE 14 CS D953 15 VSSG (AE/AF LOCK(GREEN)) LCD901 1.5INCH 16 VDDG COLOR 17 VSS LCD UNIT 18 VDD CONTROLL D954 19 DWN (SELF TIMER/REC(RED)) 20 EN 21 VCK 22 VST 23 COM 24 TESTL CN953 S951 6 PANEL_3.2V DSPL/LCDM D901 MENU ON/OFF BT9015 NC BATTERY TERMINAL BACK LIGHT S954 S9554 BL_FB 3 BL_H 2 NC 1 BL_L

N 05 FRAME (2/2)

4-5 4-6 CN101 21P GND 1 H1 2 RG 3 H2 4 GND 5 CAM_15V 6 CAM_-7.5V 7 GND 8 VSUB_CONT 9 VSHT 10 CCD_TEMP_AD 11 80 SP+ SP- 79 V2 12 78 REG_GND COM 77 CCD V1A 13 76 BATT/XEXT VST 75 V1B 14 74 VCK EN 73 V4 15 72 DWN VDD 71 V3A 16 70 VDDG REF 69 V3B 17 68 HST WIDE 67 GND 18 66 CRext HCK2 65 GND 19 64 HCK1 PSIG 63 OUT 20 62GR61 GND 21 60 B RGT 59 58 BL_L2 VSS 57 56 BL_ON VSS 55 54 BL_L1 BATT_SIG 53 52 BL_LEV REG_GND 51 50 FAST_CHARGE REG_GND 49 48 INIT_CHARGE KEY_AD0 47 46 KEY_AD1 ST_UNREG 45 44 XSTB_LED ST_UNREG 43 42 XAE_LOCK_LED ST_UNREG 41 40 REG_GND CAM_-7.5V 39 38 XTALLY_LED A_4.9V 37 36 ACV_UNREG HI_UNREG 35 34 BATT_UNREG EVER_3.2V 33 32 REG_GND KEY_AD3 31 30 D_1.8V D_1.8V 29 28 M_5V PANEL_3.2V 27 26 M_5V M_5V 25 24 REG_GND(MT_GND) REG_GND(MT_GND) 23 22 REG_GND(MT_GND) REG_GND 21 20 REG_GND REG_GND 19 18 REG_GND REG_GND 17 16 REG_GND REG_GND 15 14 REG_GND REG_GND 13 12 REG_GND BL_VO- 11 10 D_3.2V A_3.2V98D_3.2V A_3.2V76XCS_DDCON UNREG_SO54UNREG_SCK 3.2V32SYS_DD_ON CAM_15V 1 CN201 17P TEMP_OUT 1 SENS_GND 2 FOCUS_RST 3 SENS_VCC 4 SENS_VCC 5 CN904 8P FOCUS_B68A_OUT FOCUS_A77REG_GND FOCUS_B86V_OUT FOCUS_A95AV_JACK_IN GND 10 4 REG_GND GND 11 3 D+ HALL- 12 2 D- BIAS- 13 1 USB_DET HALL+ 14 BIAS+ 15 DRIVE- 16 DRIVE+ 17, 4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-340 (CCD IMAGER) PRINTED WIRING BOARD – Ref. No.: CD-340 board; 2,000 series – • For Printed Wiring Board. • There are a few cases that the part isn't mounted in this model is printed on this diagram. • Chip parts Transistor

C

20 11BE110

CDD IMAGER

CD-340 4-7 4-8,

CD-340 (CCD IMAGER) SCHEMATIC DIAGRAM • See page 4-7 for CD-340 printed wiring board.

1234567

CD-340 BOARD (CD-340 BOARD is replaced as a LENS BLOCK ASSY) A CCD IMAGER(CCD BLOCK)

-REF.NO.:2,000 SERIES-

XX MARK:NO MOUNT

Note:voltage and waveforms of parts mounted on CD-340 board cannot be measured because they are(mounted)by the side of the lens. R505

B C5073300 XX C50610p

Q502 2SC4250(T5LSONY1) C503 0.1u R506 BUFFER

IC501

LND521 21 GND 16V 0 CCD IMAGER LND520 20 CCD_OUT LND519 19 GND LND518 18 GND LND517 17 V3B LND516 16 V3A

C LND515 15 V4

LND514 14 V1B 10987654321LND513 13 V1A SY-73 BOARD (1/11) LND512 12 V2 CN101 TH501 LND511 (SEE PAGE 4-15) 11 CCD_TEMP_AD (CCD TEMP SENSOR) LND510 10 VSHT LND509 9 VSUB_CONT 11 12 13 14 15 16 17 18 19 20

D LND508 8 GNDLND507 7 CAM_-7.5V C504

LND506 6 CAM_15V 0.1u R501 120 16V R503 LND505 475 GND LND504 4 H2 R504 LND503 1M C5083 RG 0.1u LND502 C501 16V2 H1 XX LND501 1 GND C509

E 10u R50216V C5050.1u 2700

16V C502 0.1u

SIGNAL PATH 16V VIDEO Q501UN9213J-(K8).SO SIGNAL SWITCH F Y/CHROMA REC CCD IMAGER

4-9 4-10 CD-340

VOUT VDD GND RG TEST

H2

TEST

H1 V1B

GND

V1A

SUB

V2

CSUB

V3B

VL

V3A H1 V4 H2 IC501 ICX262AQF-13,

CONTROL SWITCH BLOCK, FP-380 (FLEXIBLE BOARD) SCHEMATIC DIAGRAM SW-364 (LENS COVER SWITCH) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM

– Ref. No.: SW-364 board; 2,000 series – 12345

CONTROL SWITCH BLOCK A

CONTROL SWITCH BLOCK is replaced as a block, so that PRINTED WIRING BOARD is omitted. S005 MODE DIAL

B

SET_UP

B

S004 POWER G ON/OFF(CHG) R002MOVIE TWILIGHT 400062R003 LENS COVER PLAY CAMERA 6000A1OPEN/CLOSE

C (5 POSITION MODE_DIAL)

(1st) R001 S003 20k (2nd) (SHUTTER)

D E1234

SY-73 BOARD (7/11) CN905 (SEE PAGE 4-27)

SW-364 BOARD A LENS COVER SWITCH

1234567-REF.NO.:2,000 SERIES-

FP-380 FLEXIBLE BOARD A FP-380 FLEXIBLE BOARD is replaced as a block,

so that this PRINTED WIRING BOARD is omitted.

B S201LENS COVER

OPEN/CLOSE 1 VSS LND009 LND001 1 VSS 2 VCC LND010

B LND002 2 VCC 3 SCLK LND011

LND003 3 SCLK 4 N.C. LND012 SY-73 BOARD (5/11) LND004 4 INT 5 INT LND013 MS CN501 SOCKET (SEE PAGE 4-23) LND005 5 DIO 6 N.C. LND014 Digital LND006 6 VCC 7 DIO LND015 Digital C LND007 7 BS 8 VCC LND016

C NC 1 LND201LND008 8 VSS 9 BS LND017

GND 2 LND202 10 VSS LND018 GND 3 LND203 SY-73 BOARD (7/11) CN954 SIGNAL PATH XLENS_CAP_OPN 4 LND204 (SEE PAGE 4-27) XLENS_CAP_OPN VIDEO SIGNAL 5 LND205

AUDIO

NC 6 LND206 Y/CHROMA SIGNAL

D D REC

05 PB 05 4-38

CONTROL SWITCH BLOCK/ FLEXIBLE BOARD LENS COVER SWITCH4-37 FP-380 / SW-364

14P XPWR_ON 1 XPWR_LED 2 NC 3 PWR_LED_VCC 4 D001 (POWER(GREEN)) MODE_DIAL 5 D_3.2V 6 NC 7 GND 8 NC 9 XPB_ON 10 XMOVIE 11 XSET_UP 12 XSHTR_SW 13 XAE_LOCK_SW 14,

ST-67 (FLASH DIVE) PRINTED WIRING BOARD

FLASH UNIT – Ref. No.: ST-67 board; 3,000 series – • For Printed Wiring Board. • There are a few cases that the part isn't mounted in this model is printed on this diagram. 184523A

K

4516A

E C

CN102

B

LCD902 LCD MODULE (CHARACTOR DISPLAY) BT101 ( BATTERY,LITHIUM SECONDARY) SELF TIMER/ AF ILLUMINATOR (RED) BRIGHT LEVEL SENSORCE

FLASH DRIVE

ST-67 4-39 4-40,

ST-67 (FLASH DIVE) SCHEMATIC DIAGRAM • See page 4-39 for ST-67 printed wiring board.

12345678910 11 D002

ST-67 BOARD HAU140C029TP LND001 A XE_A FLASH DRIVE(ST BLOCK) D001 R018

MA2S111-(K8).SO 1M -REF.NO.:3,000 SERIES- 4 5 LND002

XX MARK:NO MOUNT R006 C0050 27k 1u F TRIGGER

Q005 L002

FLASH NO MARK:REC/PB MODE 0 UNIT2SB1073-R-TX 3

TRANS DRIVE R010 0 270 S C008 Q011

B 120u CY25AAJ-8-T13310V FLASH DRIVE LND0032

CHARGING XE_K

CAPACITOR

R00516T001 C010 R016 0 0.047uR009 2700 47 250V C003 0.01u

C R0171M D

NC 15 LND115 COM4 COM4 14 LND114 COM3 LCD902 COM3 13 LND113 COM2 BT101 COM2 12 LND112 LITHIUM COM1 COM1 11 LND111

E BATTERY SEG9R102 LND110 LCD(BACK UP) SEG9 10

33 SEG8 MODULESEG8 9 LND109 SEG7 SEG7 8 LND108 SEG6 SEG6 7 LND107 SEG5 LND106 CHARACTERSEG5 6 SEG4 DISPLAY SEG4 5 LND105 SEG3 SEG3 4 LND104 SEG2

F SEG2 3 LND103SEG1

SEG1 2 LND102 NC 1 LND101 D101 TLOH20TP SELF TIMER/ AF ILLUMINATOR (RED)

G

Q012 TPS613-BC

BRIGHT LEVEL SENSOR H

The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que Replace only with part number specified. par une piéce portant le numéro spécifié.

FLASH DRIVE

4-41 4-42 ST-67 SY-73 BOARD (10/11) CN903 CN102 30P (SEE PAGE 4-34) 2 XPRELAMP_AF_ON PRELAMP_POWER 1 SEG1 COM4 4 SEG1 COM4 3 SEG2 COM3 6 SEG2 COM3 5 SEG3 COM2 8 SEG3 COM2 7 SEG4 COM1 10 SEG4 COM1 9 SEG6 SEG9 12 SEG6 SEG9 11 SEG5 SEG8 14 SEG5 SEG8 13 SEG7 16 REG_GND SEG7 15 18 REG_GND REG_GND 17 20 REG_GND REG_GND 19 22 REG_GND STB_FULL 21 24 REG_GND ST_UNREG 23 26 PHOTO_TR_C ST_UNREG 25 28 PHOTO_TR_OUT ST_UNREG 27 30 STB_ON1 VL_3V 29, 4-4. PARTS LOCATION no mark : SIDE A * mark : SIDE B CD-340 BOARD ST-67 BOARD C502 A-3 * BT101 C-10 C503 B-3 C504 A-3 C003 B-6 C505 A-2 C005 C-7 C506 B-2 C010 B-7 C508 A-1 C509 A-1 CN102 C-12 Q501 A-3 D001 C-7 Q502 B-3 D002 B-7 R501 A-3 Q005 C-7 R502 A-3 Q011 B-6 R503 A-3 * Q012 A-5 R504 A-3 R505 B-3 R005 B-6 R506 B-3 R006 C-7 R009 C-7 TH501 A-1 R010 B-7 R016 B-6 R017 B-5 R018 B-7 R102 C-7 T001 B-6 4-56,

SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair) PC PC (Machine after a board is replaced) Save the EVR data Download the saved to a personal computer. data to a machine. Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it. (Former board) (New board) Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or in- stalled, save the data from the same model of the same destination, and download it. (Machine to be repaired) PC (Machine to be repaired) Download the data. Save the data. (The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 5-1,

Ver 1.1 2001. 11

1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts replacement replacement Adjustment section Adjustment Initialization of B, D, Initialization of D page datazzE, F, 7, 9 page data Initialization of B, E, F, 7, 9 page datazzVideo Video sync level adj. zzzzVideo burst level adj. zzzzHall adj. zzzzCamera Flange back adj. zzzFNo. standard data inputzzzMechanical shutter adj. zzzLight value adj. zzzzAuto white balance standard data inputzzzzAuto white balance adj. zzzzColor reproduction adj. zzzzCCD (white and black) defect compensationzzzStrobe white balance adj. zzzzzzLCD LCD initial data inputzzVCO adj. zzzzBlack limit adj. zzzzBright adj. zzzzContrast adj. zzzzColor adj. zzzzPSIG adj. zzzzVG center adj. zzzzV-COM adj. zzzzzWhite balance adj. zzzzzzSystem control Battery down adj. z z Table 5-1-1 5-2 Lens block assy Flash unit LCD block LCD901 (LCD panel) LCD block D9001 (Back light unit) SY-73 board IC102 (S/H, AGC, A/D) SY-73 board IC506 (EVR) SY-73 board IC601 (VIDEO AMP) SY-73 board IC801 (LCD drive) SY-73 board IC804 (LCD Timing generator) SY-73 board IC802 (EVR) ST-67 board (COMPLETE) SY-73 board (COMPLETE) SY-73 board IC503 EEPROM, 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check J-1 Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check J-2 Pattern box PTB-450 J-6082-200-A J-3 Color bar chart for pattern box J-6020-250-A Adjusting remote commander (RM-95 upgraded). J-4 J-6082-053-B (Note 1) J-5 Siemens star chart J-6080-875-A For checking the flange back J-6 Clear chart for pattern box J-6080-621-A For connecting the adjusting remote commander J-7 CPC-9 jig (Note 2) J-6082-393-C For adjusting the LCD block J-8 Minipattern box J-6082-353-B For adjusting the flange back J-9 Back ground paper J-2501-130-A For adjusting the strobe Note 1: If the micro processor IC in the adjusting remote Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be commander is not the new micro processor (UPD7503G- used, because it cannot operate the adjusting remote C56-12), The pages cannot be switched. In this case, commander. replace with the new micro processor (8-759-148-35). J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 Fig. 5-1-1 5-3, 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer Pattern box to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-1- 6.

L

2) Connect the Adjusting remote commander to SY-73 board CN902 via CPC-9 jig (J-6082-393-C). (See Fig. 5-1-3) Note 3: Setting the “Forced CAMERA mode power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press Front of the lens the PAUSE button of the adjusting remote com- mander. The above procedure will enable the camera power to be turned on. After completing adjustments, be L = About 30 cm sure to exit the “Forced CAMERA mode power ON Mode”. Fig. 5-1-2 Note 4: Exiting the “Forced CAMERA mode power ON Mode” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjusting remote com- mander. 3) Select page: 0, address: 01, and set data: 00. 1-1-3. Discharging of the Flashlight Power Supply The capacitor which is used as power supply of flashlight is charged with 200 V to 300 V voltage. Discharge this voltage before start- CPC-9 jig ing adjustments in order to protect service engineers from electric (J-6082-393-C) (Note 1, 2) shock during adjustment. 18 CPC cover 1 Discharge procedure 1. Press the FLASH button (DD-163 board S951 (CONTROL UP)) and set the NO FLASH mode. SY-73 board 2. Fabricate the discharging jig as shown in Fig. 5-1-5 locally by CN902 yourself. Connect the discharging jig to the positive (+) and negative (–) terminal of the flash voltage charge capacitor. Al- low ten seconds to discharge the voltage. R:1 kΩ/1 W (Part code: 1-215-869-11) Note 1: Don t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) Capacitor cannot be used, because it cannot operate the adjusting remote commander. Fig. 5-1-3 1 kΩ/1 W Wrap insulating tape. Fig. 5-1-4 Fig. 5-1-5 5-4, Must be connected CONTROL SWITCH BLOCK MS SOCKET Must be connected when the MIC UNIT when the Memory Stick is used. is used. ST-67 BOARD LENS UNITCN906 CN102 CN903 CN905 CN501 CN101 SY-73 BOARD CN201 CN901 S201 CN902 CN202 (Note 3) 18 1 CN904 SW-364 BOARD CN951 DC IN jack (J652) A/V OUT jack (J651) CN953 DD-163 BOARD CN952 PANEL UNIT Audio (Black) Vectorscope Color monitor Terminated Video (yellow) 75 Ω AC IN Adjusting 18 1 remote commander Regulated AC power adaptor power supply (6.0 to 7.2 Vdc) CPC-9 jig (Note 1, 2) (J-6082-393-C) Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjusting remote commander. Note 3: Fastening the hook of the LENS COVER OPEN/ CLOSE switch (S201) on the SW-364 board with tape.

Fig. 5-1-6

5-5, 1-1-4. Precautions 1. Setting the Switch Unless otherwise specified, set the switches as follows and per- form adjustments. 1. Mode Dial ... CAMERA 2. ZOOM switch (DD-163 board S952, 953) ... WIDE end 3. EV (Menu display) ... 0EV 4. DSPL/LCD ON/OFF button (DD-163 board S954) ... OSD OFF 5. WB (WHITE BALANCE) (Menu display) ... AUTO 6. P.EFFECT (Menu display) ... OFF 7. DEMO (SET UP setting) ... OFF 8. VIDEO OUT (SET UP setting) ... NTSC 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame

H

C C=D D CRT picture frame

V

A B A=BBAFig. b (monitor TV picture) Enlargement Difference in level Adjust the camera zoom and direction to obtain the output waveform shown in Fig a and the monitor TV display shown in Fig. b. B A Fig. 5-1-7 3. Subjects 1) Color bar chart (Standard picture frame). When performing adjustments using the color bar chart, ad- just the picture frame as shown in Fig. 5-1-7. (Standard pic- ture frame) 2) Clear chart (Standard picture frame) Remove the color bar chart from the pattern box and insert a White clear chart in its place. (Do not perform zoom operations dur- 841 mm ing this time) Black 3) Chart for flange back adjustment Join together a piece of white A0 size paper (1189mm × 841 mm) and a piece of black paper to make the chart shown in Fig. 5-1-8. 1189 mm Note: Use a non-reflecting and non-glazing vellum paper. The Fig. 5-1-8 size must be A0 or larger and the joint between the white and black paper must not have any undulations. 5-6 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15 mm thickness. woody board A (2) woody board B (2) woody board C (1) 530 mm 500 mm 1000 mm 1026 mm 1026 mm 1000 mm 1030 mm 1000 mm Fig. 5-1-9 2) Apply black mat paint to one side of woody board A and B. 3) Attach background paper (J-2501-130-A) to woody board C. 4) Assemble so that the black sides and the background paper side of woody board A, B and C are internal. (Fig 5-1-10) woody board A woody board B woody board A woody board B woody board C Fig. 5-1-10 5-7, 1-2. INITIALIZATION OF B, D, E, F, 7, 9 PAGE DATA 3. D Page table 1-2-1. Initialization of D Page Data Note 1: Fixed data-1: Initialized data. 1. Initializing D Page Data (Refer to “1. Initializing the D Page Data”) Note: If the D page data has been initialized, the following Note 2: Fixed data-2: Modified data. adjustments need to be performed again. (Refer to “2. Modification of D Page Data”) 1) Modification of D page data Address Initial value Remark 2) Video system adjustments 3) LCD system adjustments 10 00 Test mode 4) System control system adjustments 11 to 4E Fixed data-1 (Initialized data) 4F Fixed data-2 Adjusting page D 50 to 8F Fixed data-1 (Initialized data) Adjusting Address 10 to EF 90 80 Initializing Method: 91 88 Order Page Address Data Procedure 92 AD Battery down adj. 93 C21001 012403 0F 94 CD3400 2D 95 to C5 Fixed data-1 (Initialized data) 4 4 01 2D Press PAUSE button. C6 5A Video sync level adj. 5 4 02 Check the data changes to “01”. C7 61 Video burst level adj. Perform “Modification of D C8 to CD Fixed data-1 (Initialized data) 6 page Data”. CE Fixed data-2

CF

2. Modification of D Page Data D0 76 Bright adj. If the D page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input. D1 C3 Color adj. D2 60 Modifying Method: White balance adj.D3 AA 1) Before changing the data, select page: 0, address: 01, and set data: 01. D4 B9 Contrast adj. 2) New data for changing are not shown in the tables because D5 5C Black limit adj. they are different in destination. When changing the data, copy D6 AC VG center adj. the data built in the same model. Note: If copy the data built in the different model, the camera D7 5C VCO adj. (NTSC) may not operate. D8 77 V-COM adj. 3) When changing the data, press the PAUSE button of the D9 Fixed data-2 adjusting remote commander each time when setting new data to write the data in the non-volatile memory. DA 61 PSIG adj. 4) Check that the data of adjustment addresses is the initial value. DB If not, change the data to the initial value. Fixed data-2DC Processing after Completing Modification of D Page Data: DD 6A VCO adj. (PAL)

DE

Order Page Address Data Procedure Fixed data-2

DF

1 2 00 29 E0 to EF Fixed data-1 (Initialized data) 2 2 01 29 Press PAUSE button. 5-8, 1-2-2. Initialization of B, E, F, 7, 9 Page Data 3. B Page Table 1. Initializing B, E, F, 7, 9 Page Data Note 1: Fixed data-1: Initialized data. Note: If the B, E, F, 7, 9 Page data has been initialized, (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) “Modification of B, E, F, 7, 9 Page Data” and following Note 2: Fixed data-2: Modified data. adjustments need to be performed again. (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) 1) Modification of B, E, F, 7, 9 page data Address Initial value Remark 2) Camera system adjustments 00 to FF Fixed data-1 (Initialized data) Adjusting page B Adjusting Address 00 to FF Adjusting page E 4. E Page Table Note 1: Fixed data-1: Initialized data. Adjusting Address 00 to FF (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) Adjusting page F Note 2: Fixed data-2: Modified data. Adjusting Address 10 to FF (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) Adjusting page 7 Address Initial value Remark Adjusting Address 00 to FF 00 to FF Fixed data-1 (Initialized data) Adjusting page 9 Adjusting Address 00 to FF Initializing Method: Order Page Address Data Procedure1001 012B00 00 Press PAUSE button. 3 6 03 0F4600 2D5601 2D Press PAUSE button. 6 6 02 Check the data changes to “01”. Perform “Modification of B, E, F, 7, 9 page Data”. 2. Modification of B, E, F, 7, 9 Page Data If the B, E, F, 7, 9 Page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camera may not operate. 3) When changing the data, press the PAUSE button of the adjusting remote commander each time when setting new data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. Processing after Completing Modification of B, E, F, 7, 9 Page data Order Page Address Data Procedure1200 292201 29 Press PAUSE button. 5-9, 5. F Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7, 9 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modified of B, E, F, 7, 9 Page Data”) Address Initial value Remark Address Initial value Remark 10 to 13 Fixed data-1 (Initialized data) 47 73 Color reproduction adj. 14 36 48 45 15 54 49 to 4C Fixed data-1 (Initialized data) 16 87 4D 28 Strobe white balance adj. 17 71 4E 6E 18 10 4F to 58 Fixed data-1 (Initialized data) 19 C0 59 00 Auto white balance standard data input 1A 00 5A 14 Mechanical shutter adj. 1B 00 5B Fixed data-1 (Initialized data) 1C 00 5C 63 1D 00 Flange back adj. 5D 83 Color reproduction adj. 1E 00 5E 03 1F 00 5F E9 20 20 60 to 63 Fixed data-1 (Initialized data) 21 20 64 10 Strobe white balance adj. 22 13 65 to 68 Fixed data-1 (Initialized data) 23 46 69 02 24 0A 6A 79 Strobe white balance adj. 25 00 6B F8 26 85 6C 09 27 B0 Light value adj. 6D E6 28 94 6E 05 29 00 6F D5 2A 00 70 04 2B 00 F No. standard data input 71 9B 2C 00 72 03 2D 00 73 DC 2E 66 74 03 Hall adj. 2F 8B 75 50 30 to 33 Fixed data-1 (Initialized data) 76 01 Mechanical shutter adj. 34 15 77 01 Hall adj. 35 78 78 01 36 to 39 Fixed data-1 (Initialized data) 79 01 3A 2F 7A 00 3B 37 7B 09 Auto white balance standard data input 3C 40 7C 17 3D D0 7D 33 3E Fixed data-1 (Initialized data) 7E 33 3F B5 7F 33 Auto white balance adj. 40 43 80 00 Auto white balance adj. 41 03 81 to 86 Fixed data-1 (Initialized data) 42 E9 87 FF Flange back adj. 43 63 88 to A8 Fixed data-1 (Initialized data) Color reproduction adj. 44 83 A9 0A Auto white balance adj. 45 D5 AA 01 46 FE AB to D3 Fixed data-1 (Initialized data) 5-10, Address Initial value Remark D4 80 D5 98 D6 A0 Mechanical shutter adj. D7 88 D8 80 D9 to E2 Fixed data-1 (Initialized data) E3 Fixed data-2 E4 to FF Fixed data-1 (Initialized data) 5-11, 6. 7 Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7, 9 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modified of B, E, F, 7, 9 Page Data”) Address Initial value Remark Address Initial value Remark 00 to 5F Fixed data-1 (Initialized data) 8F FF 60 0F 90 0F 61 FF 91 FF 62 0F 92 0F 63 FF 93 FF 64 0F 94 0F 65 FF 95 FF 66 0F 96 0F 67 FF 97 FF 68 0F 98 0F 69 FF 99 FF 6A 0F 9A 0F 6B FF 9B FF 6C 0F 9C 0F 6D FF 9D FF 6E 0F 9E 0F 6F FF 9F FF 70 0F A0 0F 71 FF A1 FF 72 0F A2 0F CCD black defect compensation 73 FF A3 FF 74 0F A4 0F 75 FF A5 FF 76 0F A6 0F CCD white defect compensation 77 FF A7 FF 78 0F A8 0F 79 FF A9 FF 7A 0F AA 0F 7B FF AB FF 7C 0F AC 0F 7D FF AD FF 7E 0F AE 0F 7F FF AF FF 80 0F B0 0F 81 FF B1 FF 82 0F B2 0F 83 FF B3 FF 84 0F B4 0F 85 FF B5 FF 86 0F B6 0F 87 FF B7 FF 88 0F B8 0F 89 FF B9 FF 8A 0F BA 0F 8B FF CCD white defect compensation BB FF 8C 0F BC 0F 8D FF BD FF 8E 0F BE 0F 5-12, Address Initial value Remark Address Initial value Remark BF FF F1 FF C0 0F F2 0F C1 FF F3 FF C2 0F F4 0F C3 FF F5 FF C4 0F F6 0F C5 FF F7 FF C6 0F F8 0F CCD white defect compensation C7 FF F9 FF C8 0F FA 0F C9 FF FB FF CA 0F FC 0F CB FF FD FF CC 0F FE 0F CD FF FF FF CE 0F CF FF 7. 9 Page Table D0 0F Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing D1 FF the B, E, F, 7, 9 Page Data”) D2 0F Note 2: Fixed data-2: Modified data. (Refer to “2. Modified of B, E, F, 7, 9 Page Data”) D3 FF D4 0F Address Initial value Remark D5 FF 00 to 67 Fixed data-1 (Initialized data) D6 0F 68 Fixed data-2 D7 FF 69 to FF Fixed data-1 (Initialized data) D8 0F CCD white defect compensation D9 FF DA 0F DB FF DC 0F DD FF DE 0F DF FF E0 0F E1 FF E2 0F E3 FF E4 0F E5 FF E6 0F E7 FF E8 0F E9 FF EA 0F EB FF EC 0F ED FF EE 0F EF FF F0 0F 5-13, 1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Adjustment 1. Video Sync Level Adjustment Adjust the burst level of the composite video signal output. Adjust the sync level of the composite video signal output. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Video terminal of A/V OUT jack Measurement Point Video terminal of A/V OUT jack (75 Ω terminated) (75 Ω terminated) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Adjustment Page D Adjustment Page D Adjustment Address C7 Adjustment Address C6 Specified Value A = 286 ± 8 mVp-p (NTSC) Specified Value A = 286 ± 5 mVp-p (NTSC) A = 300 ± 8 mVp-p (PAL) A = 300 ± 5 mVp-p (PAL) Adjusting method: Adjusting method: Order Page Address Data Procedure Order Page Address Data Procedure1001 011001 0124F1 0424F1 04 Change the data and set the Change the data and set the3DC7 burst level (A) to the3DC6 sync level (A) to the specified specified value. value. 4 D C7 Press PAUSE button4DC6 Press PAUSE button Processing after Completing Adjustments: Processing after Completing Adjustments: Order Page Address Data Procedure Order Page Address Data Procedure14F1 0014F1 002001 002001 00

A A

H H Fig. 5-1-11 Fig. 5-1-12 5-14, 1-4. CAMERA SYSTEM ADJUSTMENTS After completing the camera system adjustments, Before perform the camera system adjustments, check that the release the data setting: specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Order Page Address Data Procedure isfied. Note: For “CAMERA SYSTEM ADJUSTMENTS”, perform in1406 00 order of item numbers. 2 6 6C 003F38 B3 Press PAUSE button. Data setting during camera system adjustments Perform the following data setting before the camera system ad- 4 F DE 0F Press PAUSE button. justments. 5 F E3 0B Press PAUSE button. 6 B 75 10 Press PAUSE button. Set up setting: 1) VIDEO OUT of SET UP setting ... NTSC (NTSC mode) 7 9 F1 5A Press PAUSE button. (This adjustment must be performed in NTSC mode, so don't8D11 00 Press PAUSE button. set the SET UP setting to “PAL”) 9 D 10 00 Press PAUSE button. Data setting method: 10 0 01 00 Order Page Address Data Procedure1001 012D10 80 Press PAUSE button. Check the bit values of bit3, 3 2 10 bit4 and bit5 are “1”. (Note 1, 2) 4 D 11 40 Press PAUSE button. 5 D 10 81 Press PAUSE button. Check the data changes to56C1 “02”. 6 4 06 01766C 01 8 Wait for 1 second. 9 F 38 B1 Press PAUSE button. 10 F DE 1E Press PAUSE button. 11 F E3 13 Press PAUSE button. 12 B 75 00 Press PAUSE button. 13 9 F1 A5 Press PAUSE button. Note 1: For the bit values, refer to “5-2. SERVICE MODE”, “2-3. 2. Bit value discrimination”. Note 2: In case of wrong data, select page: 2, address: 0A and set data: 02. Set the adjusting remote commander to normal LANC, and the power will be turned off and on automatically. Wait for more than 0.167 second after the power on, and set the adjusting remote commander to the service LANC. Then, retry from the step 1. Note 3: Repeat the “Data setting method”, if the power was turned off and on during the “CAMERA SYSTEM ADJUST- MENTS”. 5-15, 1. HALL Adjustment Processing after Completing Adjustment: For detecting the position of lens iris, adjust the HALL AMP gain Order Page Address Data Procedure and offset. 1 0 03 00 Mode CAMERA2601 00 Press PAUSE button. Subject Not required Release the data setting Measurement Point Displayed data of page: 1 (Note 2) 3 performed at step 2. (Refer to page 5-15) Measuring Instrument Adjusting remote commander4001 00 Adjustment Page F Adjustment Address 2E, 2F, 34, 35 Specified Value 13 to 17 during IRIS OPEN 7B to 7F during IRIS CLOSE Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Note 2: The right 2 digits of the page: 1 displayed data of the adjusting remote commander. 1:00:XX Displayed data Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 6 01 6D Press PAUSE button. (Note 3) 4 6 02 Check the data changes to “01”. 5 6 01 00 Press PAUSE button. 6 0 03 037601 01 Press PAUSE button. Check that the displayed data81(Note 2) during IRIS OPEN satisfies the specified value. 9 6 01 03 Press PAUSE button. Check that the displayed data 10 1 (Note 2) during IRIS CLOSE satisfies the specified value. Note 3: The adjustment data will be automatically input to page: F, address: 2E, 2F, 34 and 35. 5-16, 2. Flange Back Adjustment (Using the minipattern box) Specified voltage: The specified voltage varies according to the The flange back of inner focus lens is adjusted automatically. If minipattern box, so adjustment the power sup- shifted, the auto focus is disordered. ply output voltage to the specified voltage writ- ten on the sheet which is supplied with the mini- Mode CAMERA pattern box. Subject Siemens star chart with ND filter Below 3 cm for minipattern box (Note 1) Minipattern box Measurement Point Check operation on TV monitor Measuring Instrument Camera Adjustment Page F Camera Adjustment Address 14 to 25, 87 table Note 1: Dark Siemens star chart. Regulated power supply Note 2: Check that the data of page: 6, address: 02 is “00”. Output voltage : Specified voltage ± 0.01 Vdc If not, turn the power of unit OFF/ON. Output current : more than 3.5 A Preparations before adjustments: 1) The minipattern box is installed as shown in the following fig- Red (+) ure. Note 3: The attachment lenses are not used. Black (–) 2) Install the minipattern box so that the distance between it and Yellow (SENS +) the front of lens of camera is less than 3 cm. 3) Make the height of minipattern box and the camera equal. White (SENS –) Need not connected 4) Check the output voltage of the regulated power supply is the Black (GND) specified voltage ± 0.01 Vdc. 5) Check that the center of Siemens star chart meets the center of Fig. 5-1-13 shot image screen with the zoom lens at TELE end and WIDE end respectively. Adjusting method: 6) Check that the data on page: F, address: 14 to 25 and 87 are initial value (See table below). Order Page Address Data Procedure1001 01 Address Data Address Data Perform “Data setting during 14 36 1E 00 2 camera system adjustments”. 15 54 1F 00 (Refer to page 5-15) 16 87 20 203601 13 Press PAUSE button. 17 71 21 204601 27 Press PAUSE button. (Note 4) 18 10 22 135602 Check the data changes to “01”. 19 C0 23 466F87 Check the data changes to “00”. 1A 00 24 0A Note 4: The adjustment data will be automatically input to page: 1B 00 25 00 F, address: 14 to 25 and 87. 1C 00 87 FF Processing after Completing Adjustment: 1D 00 Order Page Address Data Procedure1601 00 Press PAUSE button. Release the data setting 2 performed at step 2. (Refer to page 5-15) 3 0 01 00 4 Perform“Flange Back Check”. 5-17, 3. Flange Back Adjustment Adjusting method: (Using the flange back adjustment chart) Order Page Address Data Procedure The flange back of inner focus lens is adjusted automatically. If shifted, the auto focus is disordered. 1 0 01 01 Perform “Data setting during Mode CAMERA 2 camera system adjustments”. Subject Flange back adjustment chart (Refer to page 5-15) (2.0 m from the front of the lens) 3 6 01 13 Press PAUSE button. (Luminance: 300 to 400 lux) 4 6 01 15 Press PAUSE button. (Note 2) Measurement Point Check operation on TV monitor5602 Check the data changes to “01”. Measuring Instrument6F87 Check the data changes to “00”. Adjustment Page F Note 2: The adjustment data will be automatically input to Adjustment Address 14 to 25, 87 page: F, address: 14 to 25 and 87. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Processing after Completing Adjustment: Order Page Address Data Procedure Preparations before adjustments: 1) Place the Flange back adjustment chart 2.0 m from the front1601 00 Press PAUSE button. of the lens. Release the data setting 2) Check that the center of Flange back adjustment chart meets 2 performed at step 2. the center of shot image screen with the zoom lens at TELE (Refer to page 5-15) end and WIDE end respectively. 3 0 01 00 3) Check that the data on page: F, address: 14 to 25 and 87 are initial value (See table below). 4 Perform“Flange Back Check”. Address Data Address Data 14 36 1E 00 15 54 1F 00 16 87 20 20 17 71 21 20 18 10 22 13 19 C0 23 46 1A 00 24 0A 1B 00 25 00 1C 00 87 FF 1D 00 5-18,

Ver 1.1 2001. 11

4. Flange Back Check Mode CAMERA Subject Siemens star chart (50 cm from the front of the lens) (Luminance: 200 to 400 lux) Measurement Point Check operation on the TV Measuring Instrument monitor Specified value Lens is focused Checking method: Order Page Address Data Procedure Place the Siemens star 50 cm from the front of the lens. To open the IRIS , decrease 1 the luminous intensity to the Siemens star up to a point before noise appear on the image. 2 0 01 01 Perform “Data setting during 3 camera system adjustments”. (Refer to page 5-15) 4 6 2C 015692 706693 557601 79 Press PAUSE button. 8 6 07 Check the data changes to “01”. Check that the lens is focused. Processing after Completing Adjustment: Order Page Address Data Procedure1601 00262C 003692 004693 00 Release the data setting 5 performed at step 3. (Refer to page 5-15) 6 0 01 00 5-19, 5. Picture Frame Setting How to reset the zoom and focus when they deviated: Mode CAMERA Order Page Address Data Procedure162C 01 Subject Color bar chart (Color reproduction adjustment2692 YL (Note 2) frame with the zoom lens at3693 YH (Note 2) WIDE end) 4 6 01 79 Press PAUSE button. Measurement Point Video terminal of A/V OUT jackΩ5607 Check the data changes to “01”.(75 terminated) 6 6 01 00 Press PAUSE button. Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Note 2: The data noted down at step 8 of “Setting method”. Note 1: Displayed data of the page 1 of adjusting remote com- Check on the oscilloscope mander. 1:XX:XX 1. Horizontal period YL data YH data A=B C=DBCSwitch setting: 1) FOCUS (Menu setting) ... AUTOAD2) MACRO (Control button) ... ON Setting method: Order Page Address Data Procedure1001 01 Shoot the color bar chart with the zoom WIDE end. Enter the output of VIDEO 3 OUT to the TV monitor, and move to the position as shown in Fig. 5-1-16. Horizontal width of one color (B, C) and that of black 4 (A, D) on the color bar chart should be same. (See Fig. 5- 1-14) Fig. 5-1-14 With vertical width of black 2. Vertical period (E, F) set in same, the color 5 bar chart should come to the E E=F F center of TV monitor. (See Fig. 5-1-15) Check that the color bar on the TV monitor is focused. 7 0 03 22 V Note down the YH and YL81data. (Note 1) Fig. 5-1-15 Processing after Completing Adjustment: Check on the TV monitor Order Page Address Data Procedure1003 002001 00 Color bar chart picture frame TV monitor picture frame Fig. 5-1-16 5-20, 6. F No. Standard Data Input 7. Mechanical Shutter Adjustment Compensate the unevenness of the iris meter sensitivity. Adjust the period which the mechanical shutter is closed, and com- pensate the exposure. Mode CAMERA Subject Clear chart Mode CAMERA (Color reproduction adjustment Subject Clear chart frame with the zoom lens at WIDE (Color reproduction adjustment end) frame with the zoom lens at WIDE Adjustment Page F end) Adjustment Address 29 to 2D Adjustment Page F Note 1: Check that the data of page: 6, address: 02 is “00”. Adjustment Address 5A, 6C to 7F, D4 to D8 If not, turn the power of unit OFF/ON. Note 1: Check that the data of page: 6, address: 02 is “00”. Note 2: Refer to “Picture Frame Setting” for YH and YL. If not, turn the power of unit OFF/ON. Note 2: Refer to “Picture Frame Setting” for YH and YL. Adjusting method: Order Page Address Data Procedure Adjusting method: 1 0 01 01 Order Page Address Data Procedure Perform “Data setting during1001 01 2 camera system adjustments”. Perform “Data setting during (Refer to page 5-15) 2 camera system adjustments”. 3 6 2C 01 (Refer to page 5-15) 4 6 92 YL (Note 2) 3 6 2C 015693 YH (Note 2) 4 6 92 YL (Note 2) 6 6 01 79 Press PAUSE button. 5 6 93 YH (Note 2) 7 6 07 Check the data changes to “01”. 6 6 01 79 Press PAUSE button. 8 6 01 00 Press PAUSE button. 7 6 07 Check the data changes to “01”. 9 6 01 BB Press PAUSE button. (Note 3) 8 6 01 00 Press PAUSE button. 10 6 02 Check the data changes to “01”. 9 6 01 AD Press PAUSE button. (Note 3) Note 3: The adjustment data will be automatically input to page: 10 6 02 Check the data changes to “01”. F, address: 29 to 2D. 11 6 AB Check the data is “00”. Note 3: The adjustment data will be automatically input to page: Processing after Completing Adjustment: F, address: 5A, 6C to 7F and D4 to D8. Order Page Address Data Procedure1601 00 Press PAUSE button. Processing after Completing Adjustment: 2 6 2C 00 Order Page Address Data Procedure3692 001601 00 Press PAUSE button. 4 6 93 00262C 00 Release the data setting3692 00 5 performed at step 2 . 4 6 93 00 (Refer to page 5-15) Release the data setting6001 00 5 performed at step 2 . (Refer to page 5-15) 6 0 01 00 5-21, 8. Light Value Adjustment Processing after Completing Adjustment: Adjust the standard light value. Order Page Address Data Procedure Mode CAMERA1003 00 Subject Clear chart2601 00 Press PAUSE button. (Color reproduction adjustment362C 00 frame with the zoom lens at4692 00 WIDE end) 5 6 93 00 Measurement Point Displayed data of page: 1 (Note 3) and page: F, address: 28 Release the data setting 6 performed atstep 2. Measuring Instrument Adjusting remote commander (Refer to page 5-15) Adjustment PageF7001 00 Adjustment Address 26 to 28 Specified Value AE level 1: 0FE0 to 1020 AE level 2: 28 to 48 Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Note 2: Refer to “Picture Frame Setting” for YH and YL. Note 3: The right 4 digits of the page: 1 displayed data of the adjusting remote commander. 1:XX:XX Displayed data Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 6 2C 014692 YL (Note 2) 5 6 93 YH (Note 2) 6 6 01 79 Press PAUSE button. 7 6 07 Check the data changes to “01”. 8 6 01 00 Press PAUSE button. 9 6 01 0D Press PAUSE button. (Note 4) 10 6 02 Check the data changes to “01”. 11 0 03 06 Check that the displayed data (Note 3) 12 1 satisfies the AE level 1 specified value. Check that the displayed data 13 F 28 satisfies AE level 2 specified value. Note 4: The adjustment data will be automatically input to page: F, address: 26 to 28. 5-22, 9. Auto White Balance Standard Data Input Adjust the white balance standard data at 3200K. Mode CAMERA Subject Clear chart (Color reproduction adjustment frame) Adjustment Page F Adjustment Address 3A to 3D, 59 Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Note 2: Refer to “Picture Frame Setting” for YH and YL. Note 3: “Auto White Balance Standard Data Input” is available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 6 2C 014692 YL (Note 2) 5 6 93 YH (Note 2) 6 6 01 79 Press PAUSE button. 7 6 07 Check the data changes to “01”. 8 6 01 00 Press PAUSE button. 9 6 01 11 Press PAUSE button. 10 6 01 0B Press PAUSE button. (Note 4) 11 6 02 Check the data changes to “01”. Note 4: The adjustment data will be automatically input to page: F, address: 3A to 3D and 59. Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. 2 6 2C 003692 004693 00 Release the data setting 5 performed at step 2. (Refer to page 5-15) 6 0 01 00 5-23, 10. Auto White Balance Adjustment Order Page Address Data Procedure Adjust to the proper auto white balance output data. If it is not correct, auto white balance and color reproducibility 18 0 03 05 will be poor. Check that the displayed data 19 1 (Note 3) satisfied the B ratio Mode CAMERA specified value. Subject Clear chart Note 5: The adjustment data will be automatically input to page: (Color reproduction adjustment F, address: 3F, 40, 80, A9 and AA. frame) Filter Filter C14 for color temperature Processing after Completing Adjustment: correction Order Page Address Data Procedure Measurement Point Displayed data of page: 1 (Note 3) 1 0 03 00 Measuring Instrument Adjusting remote commander2601 00 Press PAUSE button. Adjustment PageF362C 00 Adjustment Address 3F, 40, 80, A9, AA4692 00 Specified Value R ratio: 2A60 to 2BA05693 00 B ratio: 5C60 to 5DA0 Note 1: Check that the data of page: 6, address: 02 is “00”. 6 F 4A Set data noted down at step 11, If not, turn the power of unit OFF/ON. 4B and press PAUSE button. Note 2: Refer to “Picture Frame Setting” for YH and YL. 4C Note 3: The right 4 digits of the page: 1 displayed data of the Release the data setting per- adjusting remote commander. 7 formed at step 3. (Refer to 1:XX:XX page 5-15) Displayed data8001 00 Note 4: “Auto White Balance Adjustment” is available only once Remove the C14 filter on the after the power is turned on. Turn the power off, then on 9 lens. again if the adjustment is retried. Adjusting method: Order Page Address Data Procedure 1 Place the C14 filter on the lens. 2 0 01 01 Perform “Data setting during 3 camera system adjustment”. (Refer to page 5-15) 4 6 2C 015692 YL (Note 2) 6 6 93 YH (Note 2) 7 6 01 79 Press PAUSE button. 8 6 07 Check the data changes to “01”. 9 6 01 00 Press PAUSE button. 10 6 01 A7 Press PAUSE button. 11 F 4A Note down the data. 4B 4C 49 2B 12 F 4A 00 Press PAUSE button. 4B 5D 4C 00 13 6 01 A5 Press PAUSE button. (Note 5) 14 6 02 Check the data changes to “01”. 15 6 01 3F Press PAUSE button. 16 0 03 04 Check that the displayed data 17 1 (Note 3) satisfied the R ratio specified value. 5-24, 11. Auto White Balance Check Order Page Address Data Procedure Mode CAMERA INDOOR luminance point check Subject Clear chart Check that the center of the (Color reproduction adjustment 20 white luminance point within frame) the circle shown Fig 5-1-17 Filter Filter C14 for color temperature (A). correction Measurement Point Displayed data of Video terminal Processing after Completing Adjustment: of Page: 1 A/V OUT jack Order Page Address Data Procedure (Note 3) (75 Ω terminated) 1 0 03 00 Measuring Instrument Adjusting remote Vectorscope2601 00 Press PAUSE button. commander362C 00 Specified Value R ratio: Fig. 5-1-17 3E00 to 4200 (A) and (B) 4 6 91 00 B ratio: 5 6 93 00 3E00 to 4200 Set data noted down at step 13, 6 E 52 Note 1: Check that the data of page: 6, address: 02 is “00”. and press PAUSE button. If not, turn the power of unit OFF/ON. Release the data setting per- Note 2: Refer to “Picture Frame Setting” for YH and YL. 7 formed at step 3. (Refer to Note 3: The right 4 digits of the page: 1 displayed data of the page 5-15) adjusting remote commander. 8 0 01 00 1:XX:XX Displayed data Checking method: Order Page Address Data Procedure R-Y 1 Place the C14 filter on the lens. 2 0 01 01 Perform “Data setting during B-Y4 mm 3 camera system adjustment”. (Refer to page 5-15) 4 6 2C 01 4 mm5692 YL (Note 2) 6 6 93 YH (Note 2) Fig. 5-1-17 (A) 7 6 01 79 Press PAUSE button. 8 6 07 Check the data changes to “01”. 9 6 01 00 Press PAUSE button. R-Y OUTDOOR luminance point check 1 mm 10 6 01 3F Press PAUSE button. B-Y Check that the center of the 1.5 mm 11 white luminance point settles 6 mm in the circle shown Fig 5-1-17 (B). INDOOR data check 6 mm Remove the C14 filter on the 12 lens. Fig. 5-1-17 (B) 13 E 52 Note down the data. 14 E 52 1B Press PAUSE button. 15 6 01 0F Press PAUSE button. 16 0 03 04 Check that the displayed data 17 1 (Note 3) satisfied the R ratio specified value. 18 0 03 05 Check that the displayed data 19 1 (Note 3) satisfied the B ratio specified value. 5-25, 12. Color Reproduction Adjustment Processing after Completing Adjustment: Adjust the color separation matrix coefficient so that proper color reproduction is produced. Order Page Address Data Procedure1601 00 Press PAUSE button. Mode CAMERA262C 00 Subject Color bar chart3692 00 (Color reproduction adjustment frame with the zoom lens at4693 00 WIDE end) Release the data setting Adjustment Page F performed at step 2 . (Refer to page 5-15) Adjustment Address 41 to 48, 5C to 5F6001 00 Note 1: Perform “Auto White Balance Standard Data Input” be- Perform “Color Reproduc- fore this adjustment. 7 tion Check”. Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of the unit OFF/ON. Note 3: Refer to “Picture Frame Setting” for YH and YL. Note 4: “Color Reproduction Adjustment” is available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 6 2C 014692 YL (Note 3) 5 6 93 YH (Note 3) 6 6 01 79 Press PAUSE button. 7 6 07 Check the data changes to “01”. 8 6 01 00 Press PAUSE button. 9 6 01 AB Press PAUSE button. 10 6 12 80 11 Wait for 1 second. 12 6 12 00 13 Wait for 2 seconds. 14 6 01 A9 Press PAUSE button. (Note 5) 15 6 02 Check the data changes to “01”. Note 5: The adjustment data will be automatically input to page: F, address: 41 to 48 and 5C to 5F. 5-26, 13. Color Reproduction Check Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Color bar chart1601 00 Press PAUSE button. (Color reproduction adjustment2610 00 frame with the zoom lens at362C 00 WIDE end) 4 6 92 00 Measurement Point Video terminal of A/V OUT jack5693 00 (75 Ω terminated) Set the data noted down at Measuring Instrument Vectorscope6E52 step 10, and press PAUSE Specified Value All color luminance points button. should settle within each color Release the data setting reproduction frame. 7 performed at step 2 . (Refer Note 1: Refer to “Picture Frame Setting” for YH and YL. to page 5-15) 8 0 01 00 Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during R-Y 2 camera system adjustments”. (Refer to page 5-15) 3 6 2C 01 R MG4692 YL (Note 1) 5 6 93 YH (Note 1) 6 6 01 79 Press PAUSE button. 7 6 07 Check the data changes to “01”. YE8601 00 Press PAUSE button. B-Y9610 01 B 10 E 52 Note down the data. 11 E 52 09 Press PAUSE button. 12 6 01 0F Press PAUSE button. 13 6 12 80 CY

G

14 Wait for 1 second. 15 6 12 00 Burst position 16 Wait for 2 seconds. Check the each color 17 luminance point is in each Fig. 5-1-18 color reproduction frame. 5-27, 14. CCD White Defect Compensation Mode CAMERA Subject Not required Measurement Point Displayed data of page: 6, address: 55 Measuring Instrument Adjusting remote commander Adjustment Page 7 Adjustment Address 88 to FF Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Note 2: The “CCD White Defect Compensation” should be made when the set warms up at certain duration after the power was turned on, as it is affected with the temperature. Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 F DE 1E Press PAUSE button. 4 F E3 13 Press PAUSE button. 5 6 01 8B Press PAUSE button. (Note 3) 6 6 02 Check the data changes to “01”. Check the data. 7 6 55 00 to 7F: Normal 80 to FF: Defective8601 00 Press PAUSE button. 9 F DE 0F Press PAUSE button. 10 F E3 60 Press PAUSE button. 11 6 01 87 Press PAUSE button. 12 6 02 Check the data changes to “01”. 13 6 55 Check the data is “00”. Note 3: The adjustment data will be automatically input to page: 7, address: 88 to FF. Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. Release the data setting 2 performed at step 2 . (Refer to page 5-15) 3 0 01 00 5-28, 15. CCD Black Defect Compensation Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Clear chart1601 00 Press PAUSE button. (20 cm from the front of lens) 2 6 2C 00 Measurement Point Displayed data of page: 6, 3 6 30 00 address: 55 Set the data noted down at Measuring Instrument Adjusting remote commander4FDF step 3, and press PAUSE Adjustment Page 7 button. Adjustment Address 60 to 87 Release the data setting 5 performed at step 2 . (Refer Note 1: Check that the data of page: 6, address: 02 is “00”. to page 5-15) If not, turn the power of unit OFF/ON. 6 0 01 00 Note 2: Check that there are no dust, no dirt and reflection of the clear chart. Note 3: Any subject other than the clear chart should be in the screen. Adjusting method: Order Page Address Data Procedure1001 01 Perform “Data setting during 2 camera system adjustments”. (Refer to page 5-15) 3 F DF Note down the data. 4 F DF 4C Press PAUSE button. 5 6 2C 016692 007693 008601 79 Press PAUSE button. 9 6 30 01 10 6 07 Check the data changes to “01”. 11 6 01 8D Press PAUSE button. (Note 4) 12 6 02 Check the data changes to “01”. Check the data. 00: Proceed to “Processing 13 6 55 after Completing Adjustment”. 01 to 0A: Normal 0B to FF: Defective 14 6 01 00 Press PAUSE button. 15 F DF 5A Press PAUSE button. 16 6 01 89 Press PAUSE button. 17 6 02 Check the data changes to “01”. 18 6 55 Check the data is “00”. Note 4: The adjustment data will be automatically input to page: 7, address: 60 to 87. 5-29, 16. Strobe White Balance Adjustment Order Page Address Data Procedure Adjust the white balance when the strobe light flashed. 16 6 02 Check the data changes to “01”. Mode CAMERA 17 6 01 00 Press PAUSE button. Subject Flash adjustment box (Note 3) 18 6 01 B9 Press PAUSE button. (Note 7) (1 m from the front of the lens) Check the flashing of strobe Adjustment Page F 19 light. Adjustment Address 4D, 4E, 64, 69 to 6B 20 6 02 Check the data changes to “01”. Specified Value Y level data: 70 to 90 (Note 5) 21 6 01 00 Press PAUSE button. R-Y level data: FA to FF or 00 to 06 22 6 01 67 Press PAUSE button. (Note 4) B-Y level data: FA to FF or 00 to 06 Check the flashing of strobe23 (Note 4) light. 24 6 02 Check the data changes to “01”. Note 1: Check that the data of page: 6, address: 02 is “00”. 25 0 03 02 If not, turn the power of unit OFF/ON. Note 2: Perform this adjustment in the Flash adjustment box. Check that the R-Y, B-Y level Do not block the photocell window for flash. 26 1 data (Note 4) satisfies the Restrict external light to enter the photocell window for specified value. flash as less as possible. Check that the Y level data Note 3: Refer to “4. Preparing the Flash adjustment box”. (See 27 F 64 (Note 5) satisfies the specified page 5-7) value. Note 4: The right four digits of the page: 1 displayed data of the Note 7: The adjustment data will be automatically input to page: adjusting remote commander. F, address: 4D, 4E, 64 and 69 to 6B. 1:XX:XX B-Y level data Processing after Completing Adjustment: R-Y level data Note 5: Displayed data of page: F, address: 64, of the adjusting Order Page Address Data Procedure remote commander. 1 0 03 00 F:XX:64 Y level data2601 00 Press PAUSE button. Note 6: “Strobe White Balance Adjustment” is available only362C 00 once after the power is turned on. Turn the power off, 4 6 6C 00 then on again if the adjustment is retried. 5 6 92 00 Switch setting: 6 6 93 00 1) FLASH (Control button) ... ON7614 00 Release the data setting per- Adjusting method: 8 formed at step 2. (Refer to Order Page Address Data Procedure page 5-15) 1 0 01 019001 00 Perform “Data setting during 2 camera system adjustment”. (Refer to page 5-15) 3 6 14 904692 FF5693 FF666C 01762C 018601 79 Press PAUSE button. 9 6 07 Check the data changes to “01”. 10 6 01 67 Press PAUSE button. Check the flashing of strobe light. 12 6 02 Check the data changes to “01”. 13 6 01 00 Press PAUSE button. 14 6 01 67 Press PAUSE button. Check the flashing of strobe light. 5-30, 1-5. LCD SYSTEM ADJUSTMENTS [Adjusting connector] Before perform the camera system adjustments, check that the Most of the measuring points for adjusting the LCD system are specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- concentrated in CN 902 of the SY-73 board. isfied. Connect the Measuring Instruments via the CPC-9 jig (J-6082- 393-C). Note 1: Taken an extreme care not to destroy the liquid crystal The following table shows the Pin No. and signal name of CN display module by static electricity when replacing it. 902. Note 2: Set the LCD BRIGHTENSS (SET UP setting) to the NORMAL. Pin No. Signal Name Pin No. Signal Name 1 BL_L1 10 HI_UNREG 2 N. C. 11 LANC IN 3 N. C. 12 LANC OUT 4 REG_GND 13 MAKER_RECOG 5 CPU_IN 14 N. C. 6 BL_L2 15 N. C. 7 HSY 16 N. C. 8 PANEL_COM 17 N. C. 9 VG 18 N. C. CPC-9 jig (J-6082-393-C) (Note 1, 2) CPC cover 1 SY-73 board CN902 Note 1: Don t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjusting remote commander. Fig. 5-1-19 5-31, 1. LCD Initial Data Input (1) 2. LCD Initial Data Input (2) Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Adjustment Page B Adjustment Page D Adjustment Address 3A to 3F Adjustment Address CE to DF Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: B, and enter the data given in the following table. 2) Select page: D, and enter the data given in the following table. Note: Press the PAUSE button each time the data are set, as the Note: Press the PAUSE button each time the data are set, as the data are written to non-volatile memory (EEPROM). data are written to non-volatile memory (EEPROM). Address Data Remark Address Data Remark 3A 59 CE 46 Fixed value 3B 00 CF B9 3C 04 D0 76 Bright Adjustment Fixed data 3D 5B D1 C3 Color Adjustment 3E 00 D2 60 White Blance Adjustment 3F 02 D3 AA D4 B9 Contrast Adjustment Processing after Completing Adjustments: D5 5C Black Limit Adjustment 1) Select page: 0, address: 01, and set data: 00. D6 AC VG Center Adjustment D7 5C VCO Adjustment (NTSC) D8 77 V-COM Adjustment D9 B0 Fixed value DA 61 PSIG Adjustment DB 00 Fixed value DC 4D DD 6A VCO Adjustment (PAL) DE A6 Fixed value DF B9 Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 00. 5-32, 3. VCO Adjustment (SY-73 Board) Set the VCO free-run frequency. If deviated, the LCD screen will be blurred. Mode PLAY Signal Arbitrary CH1 Measurement Point CH1: Pin 7 of CN902 (HSY) CH2: Video terminal of A/V CH2 OUTjack (75 Ω terminated) Measuring Instrument Oscilloscope H Adjustment Page D magnified Adjustment Address D7 (NTSC) DD (PAL) Specified Value T = 2.04 ± 0.1 µs (NTSC) T = 2.63 ± 0.1 µs (PAL) Menu setting: 1) VIDEO OUT of SET UP setting ... NTSC (NTSC mode) (This adjustment must be performed in NTSC mode, so don’t CH1 set the menu setting to “PAL” ) Adjusting method: Order Page Address Data Procedure CH21001 01

T

Change the data and set the2DD7 phase difference (T) to the NTSC specified value. T: Between the center of HSY signal rising and3DD7 Press PAUSE button. VIDEO SYNC signal rising Change the data and set the Fig. 5-1-204DDD phase difference (T) to the PAL specified value. 5 D DD Press PAUSE button. Processing after Completing Adjustments: Order Page Address Data Procedure1001 00 5-33,

Ver 1.1 2001. 11

4. Black Limit Adjustment (SY-73 Board) Set the maximum amplitude of the RGB decoder for driving the LCD to the specified value. If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitrary Measurement Point Pin 9 of CN902 (VG) External trigger: Pin 8 of CN902 (PANEL COM) Measuring Instrument Oscilloscope Adjustment Page D Adjustment Address D5 Specified Value A = 8.20 ± 0.1 Vp-p Adjusting method: Order Page Address Data Procedure1001 0124F1 03 Set the data. 3 D D0 20 (Don’t press PAUSE button.) Change the data and set the4DD5 voltage (A) to the specified value. 5 D D5 Press PAUSE button. Processing after Completing Adjustments: Order Page Address Data Procedure14F1 002001 00

A

2H A: Between the reversed waveform peak and non-reversed waveform peak Fig. 5-1-21 5-34,

Ver 1.1 2001. 11

5. Bright Adjustment (SY-73 Board) Pedestal Set the amplitude of the RGB decoder for driving the LCD to the specified value. If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitrary A Measurement Point Pin 9 of CN902 (VG) External trigger: Pin 8 of CN902 (PANEL COM) Measuring Instrument Oscilloscope Adjustment Page D Pedestal 2H Adjustment Address D0 Specified Value A = 7.96 ± 0.1 Vp-p A: Between the reversed waveform pedestal and non-reversed Adjusting method: waveform pedestal Order Page Address Data Procedure Fig. 5-1-221001 0124F1 03 Change the data and set the3DD0 voltage (A) to the specified value. 4 D D0 Press PAUSE button. Read the data and this data is5DD0 named Dref. Convert Dref to decimal 6 notation, and obtain Dref’. (Note) Calculate DCE’ and DDE’ using following equations. 7 (decimal calculation) DCE’ = Dref’ – 48 DDE’ = Dref’ + 48 Convert DCE’ and DDE’ to 8 hexadecimal numbers, and obtain DCE and DDE. (Note) 9 D CE DCE Press PAUSE button. 10 D DE DDE Press PAUSE button. Note: Refer to table 5-2-2. “Hexadecimal-decimal conversion table”. Processing after Completing Adjustments: Order Page Address Data Procedure14F1 002001 00 5-35,

Ver 1.1 2001. 11

6. Contrast Adjustment (SY-73 Board) 7. Color Adjustment (SY-73 Board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the color saturation to the standard value. fied value. If, deviated, the color will be dark or light. If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitray Mode PLAY Measurement Point Pin 9 of CN902 (VG) Signal Arbitrary External trigger: Pin 8 of CN902 Measurement Point Pin 9 of CN902 (VG) (PANEL COM) External trigger: Pin 8 of CN902 Measuring Instrument Oscilloscope (PANEL COM) Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D1 Adjustment Page D Specified Value A = 350 ± 50 mVp-p Adjustment Address D4 Specified Value A = 2.50 ± 0.05 Vp-p Adjusting method: Adjusting method: Order Page Address Data Procedure1001 01 Order Page Address Data Procedure24F1 041001 01 Change the data and set the24F1 032DD1 voltage (A) to the specified Change the data and set the value. 3 D D4 voltage (A) to the specified4DD1 Press PAUSE button. value. 4 D D4 Press PAUSE button. Processing after Completing Adjustments: Read the data and this data is5DD4 Order Page Address Data Procedure named Dref. 1 4 F1 006DCF Dref Press PAUSE button. 2 0 01 007DDF Dref Press PAUSE button. Processing after Completing Adjustments: Order Page Address Data Procedure14F1 002001 00 White 100% Green

A

10 steps peak 2H A A: Between the white 100% (Reference level) and green Fig. 5-1-24 Pedestal 2H A: Between the pedestal and 10 steps peak Fig. 5-1-23 5-36, 8. VG Center Adjustment (SY-73 Board) 9. PSIG Adjustment (SY-73 Board) Set the center of VG signal for driving the LCD to the specified Set the common electrode drive signal level of LCD to the speci- value. fied value. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 9 of CN902 (VG) Measurement Point Pin 8 of CN902 Measuring Instrument Digital voltmeter (PANEL_COM) Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D6 Adjustment Page D Specified Value A = 7.00 ± 0.05 V Adjustment Address DA Specified Value A = 5.0 ± 0.1 Vp-p Adjusting method: Adjusting method: Order Page Address Data Procedure1001 01 Order Page Address Data Procedure24F1 021001 01 Change the data and set the24F1 023DD6 DC voltage (A) to the specified Change the data and set the PSIG value. 3 D DA signal level (A) to the specified4DD6 Press PAUSE button. value. 4 D DA Press PAUSE button. Processing after Completing Adjustments: Order Page Address Data Procedure Processing after Completing Adjustment: 1 4 F1 00 Order Page Address Data Procedure2001 0014F1 002001 00

A

2H Fig. 5-1-25 5-37, 10. V-COM Adjustment (SY-73 Board) 11. White Balance Adjustment (SY-73 Board) Set the DC bias of the common electrode drive signal of LCD to Correct the white balance. the specified value. If deviated, the LCD screen color cannot be reproduced. If deviated, the LCD display will be move, producing flicker and Mode PLAY conspicuous vertical lines. Signal Arbitrary Mode PLAY Measurement Point Signal Arbitrary Check on the LCD screenMeasuring Instrument Measurement Point Check on the LCD screen Adjustment Page D Measuring Instrument Adjustment Address D2, D3 Adjustment Page D Specified Value LCD screen must not be colored Adjustment Address D8 Note 1: Check the white balance only when replacing the fol- Specified Value The brightness difference lowing parts. If necessary, adjust them. between the section-A and 1. LCD panel section-B is minimum 2. Light induction plate Note 1: Perform “Bright Adjustment” and “Contrast Adjusstment” 3. IC801 before this adjustment. Adjusting method: Adjusting method: Order Page Address Data Procedure Order Page Address Data Procedure1001 011001 0124F1 0224F1 02 Press PAUSE button. 3 D D2 603410 02 (Intital value) Change the data so that Press PAUSE button.AA4DD84DD3brightness of the section A (Intital value) and section B is equal. Check that the LCD screen is Read the data and this data is not colored. If not colored, 5 D D8 5named Dref. proceed to “Processing after Completing Adjustments”. Convert Dref to decimal 6 notation, and obtain Dref’. D2 Change the data so that the (Note 2) 6 D LCD screen is not colored. D3 (Note 2) Calculate DD8’ using following equations. 7 Note 2: To write in the non-volatile memory (EEPROM), press (decimal calculation) the PAUSE button each time to set the data. DD8’ = Dref’ – 13 Convert D Processing after Completing Adjustments:D8’ to a hexadeci- 8 mal number, and obtain DD8. Order Page Address Data Procedure (Note 2) 1 4 F1 009DD8 DD8 Press PAUSE button. 2 0 01 00 Note 2: Refer to table 5-2-2. “Hexadecimal-decimal conversion table”. Processing after Completing Adjustments: Order Page Address Data Procedure14F1 002410 003001 00BAABBAABFig. 5-1-26 5-38, 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENTS Adjusting method: Order Page Address Data Procedure 1. Battery Down Adjustment1001 01 Set the battery end voltage. 2 6 2C 01 If the voltage is incorrect, the life of battery will shorten. The image at the battery end will also be rough. Decrease the output voltage 3 of the regulated power supply so that digital voltmeter display Mode CAMERA is 3.20 ± 0.01 Vdc. Subject Arbitrary429A Read the data, and this data Measurement Point Displayed data of page: 2, is named Dref. address: 9A5D90 Dref Press PAUSE button. Measuring Instrument Adjusting remote commander 6 Convert Dref to decimal notati on and obtain Dref’. (Note) Adjustment Page D Calculate D91’, D92’, D93’ Adjustment Address 90 to 94 and D94’ using following equations(decimal calculation) Connection: 7 D91’=Dref’+6 1) Connect the regulated power supply and the digital voltmeter D92’=Dref’+23 D93’=Dref’+44 to the battery terminal as shown in Fig. 5-1-27. D94’=Dref’+55 Preparations before adjustment: Convert D91’, D92’, D93’ and 8 D94’ to a hexadecimal number,1) Adjust the output voltage of the regulated power supply so and obtain D91, D92, D93 and that the digital voltmeter display is 4.2 ± 0.1 Vdc. D94 (Note) 2) Turn off the power supply. 9 D 91 D91 Press PAUSE button. 3) Set the HOLD switch of the adjusting remote commander to “HOLD” (SERVICE position). 10 D 92 D92 Press PAUSE button. 4) Turn on the power supply. 11 D 93 D93 Press PAUSE button. 5) Insert the memory stick to the unit, and set the CAMERA mode. 12 D 94 D94 Press PAUSE button. Note: Refer to table 5-2-2. “Hexadecimal-decimal conversion table” Processing after Completing Adjustments: Order Page Address Data Procedure162C 002001 00 Adjusting remote commander CPC-9jig 18 (J-6082-393-C) Digital voltmeter Regulated power supply (3.20 ± 0.01 Vdc) Regulated power supply (6.0 to 7.2 Vdc) Fig. 5-1-27 5-39, 5-2. SERVICE MODE • Changing the address 2-1. ADJUSTING REMOTE COMMANDER The address increases when the FF (M) button is pressed, The adjusting remote commander is used for changing the calcu- and decreases when the REW (M) button is pressed. There lation coefficient in signal processing, EVR data, etc. The adjust- are altogether 256 addresses, from 00 to FF. ing remote commander performs bi-directional communication • Changing the data (Data setting) with the unit using the remote commander signal line (LANC). The data increases when the PLAY (N) button is pressed, The resultant data of this bi-directional communication is written and decreases when the STOP (x) button is pressed. There in the non-volatile memory. are altogether 256 data, from 00 to FF. • Writing the adjustment data 1. Used the Adjusting Remote Commander The PAUSE button must be pressed to write the adjustment 1) Connect the adjusting remote commander to the CN902 on data in the nonvolatile memory. (The new adjustment data the SY-73 board via CPC-9 jig (J-6082-393-C). will not be recorded in the nonvolatile memory if this step is 2) Set the HOLD switch of the adjusting remote commander to not performed) “HOLD” (SERVICE position). 3) Turn on the power with the POWER switch of the unit. 2. Precautions upon Using the Adjusting Remote If it has been properly connected, the LCD on the adjusting re- Commander mote commander will display as shown in Fig. 5-2-1. Mishandling of the adjusting remote commander may erase the correct adjustment data at times. To prevent this, it is recommended that all adjustment data be noted down before beginning adjust- ments and new adjustment data after each adjustment. 0 : 00 : 00 Page Data Address Fig. 5-2-1 4) Operate the adjusting remote commander as follows. • Changing the page The page increases when the EDIT SEARCH + button is pressed, and decreases when the EDIT SEARCH – button is pressed. There are altogether 16 pages, from 0 to F. Hexadecimal0123456789ABCDEFnotation LCD Display0123456789AbcdEFDecimal notation0123456789101112131415 conversion value Table 5-2-1 5-40, 2-2. DATA PROCESS The calculation of the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-2-2. indicates the hexadecimal notation- the deci- mal notation, calculation table. Hexadecimal nontation-Decimal notation 2 ↓ The lower digits of the0123456789ABCDEFhexadecimal notation The upper digits of the (A) (b) (c) (d) (E) (F) hexadecimal notation0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 1→ B (b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note : ( ) indicate the adjusting remote control unit display. (Example) In the case that the adjusting remote control unit display are BD (bd). As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection “189” of the1 and 2 in the above table is the decimal notation to be calculated. Table 5-2-2 5-41, 2-3. SERVICE MODE 3. Mode Dial Check (1) 1. Setting the Test Mode Page 2 Address 94 Page D Address 10 Data Function Data Function 00 to 14 MOVIE 00 Normal 15 to 3D TWILIGHT 01 Forced CAMERA mode power ON 3E to 67 CAMERA 02 Forced PLAY mode power ON 03 Forced MOVIE mode power ON Using method: • Before setting the data, select page: 0, address: 01, and set data: 1) Select page: 2, address: 94. 01. 2) By discriminating the bit value of dispaly data, the state of the • For page D, the data set is recorded in the non-volatile memory switches can be discriminated. by pressing the PAUSE button of the adjusting remote com- mander. In this case, take note that the test mode will not be 4. Mode Dial Check (2) exited even when the main power is turned off. • After completing adjustments/repairs, be sure to return the data Page 2 Address 80, 86 of this address to “00”, and press the PAUSE button of the ad- justing remote commander. Address Bit Function When bit When bitSelect page: 0, address: 01, and set data: 00. value=1 value=0 80 1 PLAY others PLAY 2. Bit Value Discrimination Bit values must be discriminated using the display data of the ad- 86 6 SET UP others SET UP justing remote commander for following items. Use the table be- low to discriminate if the bit value is “1” or “0”. Using method: 1) Select page: 2, address: 80 and 86. Display on the adjustilng remote commander 2) By discriminating the bit value of dispaly data, the state of the switches can be discriminated. 0 : 00 : 00 5. Switch Check (1) Page 2 Address 80 Address Page bit3 to bit0 discrimination Bit Function When bit value=1 When bit value=0 bit7 to bit4 discrimination POWER SW 0 (CONTROL OFF ON Display on the Bit values SWITCH BLOCK) Adjusting bit3 bit2 bit1 bit0 PLAY (Mode Dial) remote or or or or 1 (CONTROL others PLAY commander bit7 bit6 bit5 bit4 SWITCH BLOCK) 00000210001SHUTTR SW200103(CONTROL SWITCH OFF ON BLOCK) 30011XSHUTTER LOCK SW401004(CONTROL SWITCH OFF ON50101BLOCK) 601105MEMORY STICK OUT IN70111IN SW (MS Socket) A81000Using method: 910011) Select page: 2, address: 80. A (A) 10102) By discriminating the bit value of dispaly data, the state of the B (b) 1011switches can be discriminated. C (c) 1100D(d) 1101BE(E) 1110F(F) 1111Example: If “8E” is displayed on the adjusting remote com- mander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. 5-42, 6. Switch Check (2) Page 2 Addresses 90, 91, 93 Using method: 1) Select page: 2, addresses: 90, 91 and 93. 2) By discriminating the dispaly data, the pressed key can be discriminated. Data Address 00 to 0C 0D to 27 28 to 48 49 to 74 75 to A6 A7 to DD DE to FF 90 CONTROL DOWN CONTROL UP MENU (KEY AD0) (DD-163 board) (DD-163 board) (DD-163 board) (IC401 is) (S951) (S951) (S954) DISPLAY/LCD 91 CONTROL RIGHT CONTROL LEFT CONTROL SET ON/OFF (KEY AD1) (DD-163 board) (DD-163 board) (DD-163 board) (DD-163 board) (IC401 id) (S951) (S951) (S951) (S955) 93 ZOOM (W) ZOOM (T) (KEY AD3) (DD-163 board) (DD-163 board) (IC401 ig) (S952) (S953) 7. LED Check Page 2 Address 04 Data 01 Using method: 1) Select page: 2, address: 04, set data: 01, and press the PAUSE button of the adjusting remote commander. 2) Check that all LED except for the ACCESS LED are lit and all segments of LCD (display window) are lit. 3) Select page: 2, address: 04, set data: 00 and press the PAUSE button of the adjusting remote commander. 8. Self Diagnosis Code Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. 55-4-433 E,

SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • The mechanical parts with no reference number in Replace only with part number speci- have some difference from the original one. the exploded views are not supplied. fied. • Items marked “*” are not stocked since they are • Accessories are given in the last of the electrical Les composants identifiés par une seldom required for routine service. Some delay parts list. marque 0 sont critiquens pour la should be anticipated when ordering these items. sécurité. Ne les remplacer que par une pièce portant le numéro spécifié. 6-1-1. CABINET (FRONT) ASSEMBLY414436not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3951-989-1 CABINET (FRONT) ASSY (560) (S) (SILVER) 4 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 1 X-3951-992-1 CABINET (FRONT) ASSY (560) (B) (BLUE) 5 3-064-225-01 LID, CPC 2 3-071-056-01 PLATE (UPPER), INNER 6 3-071-128-01 KNOB, SWITCHING 3 3-071-126-01 CABINET (560), CENTER 7 3-071-129-01 SLIDER, SWITCHING 6-1, 6-1-2. CABINET (REAR) ASSEMBLY 51 56 59 61 not supplied 63 MIC901 69 54 57 64 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 1-476-875-11 SWITCH BLOCK, CONTROL 61 3-071-051-01 BUTTON, FUNCTION 52 3-071-108-01 CUSHION (MODE DIAL) 62 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 * 53 3-055-971-01 CUSHION, MICROPHONE 63 3-071-002-01 LCD WINDOW (1.5) 54 3-071-012-01 CAP, MICROPHONE 64 3-071-003-01 SHEET (1.5), ADHESIVE 55 3-713-791-71 SCREW (M1.7X4) 65 3-071-059-01 SHEET (ST), INSULATING 56 X-3951-990-1 CABINET (REAR) ASSY (560) (S) (SILVER) 66 X-3951-970-1 CABINET (BOTTOM) ASSY 56 X-3952-027-1 CABINET (REAR) ASSY (560) (B) (BLUE) 67 3-070-999-01 FOOT (UN), RUBBER 57 3-071-054-01 WINDOW, JACK 68 3-072-132-01 MA CUSHION 58 3-071-048-01 BUTTON, ZOOM 69 3-072-219-01 CUSHION (NM), MICROPHONE 59 3-071-055-01 COVER, JACK MIC901 1-542-446-21 MICROPHONE 60 3-071-052-01 HOLDER, FUNCTION BUTTON 6-2, 6-1-3. LENS BLOCK AND LCD SECTION not supplied % 104 LCD901not supplied 106 105 107 102 not supplied D901 not supplied (Note) ! : BT101 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-40.) The components identified by Les composants identifiés par une (Note) The lens block assembly is a mechanical unit which mark 0 or dotted line with marque 0 sont critiques pour la has completely been adjusted in the factroy. So never mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce disassemble the lens block assembly. ber specified. portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 A-7078-018-A SY-73 BOARD, COMPLETE (SERVICE) 108 3-071-019-01 SHEET, PROTECTION 102 3-713-791-71 SCREW (M1.7X4) 109 A-7031-343-A LENS BLOCK ASSY (Note) 103 3-071-017-01 SHEET (STROBOSCOPE), INSULATING 110 3-064-216-01 CUSHION (L) 104 A-7074-974-A ST-67 BOARD, COMPLETE 111 3-064-215-01 SCREW (M1.7), STEP 105 3-071-035-01 FRAME, LENS 112 A-7074-987-A SW-364 BOARD, COMPLETE 0D901 1-476-931-11 BLOCK LIGHT GUIDE PLATE (1.5) 106 3-071-020-01 SHEET (LCD), LIGHT INTERCEPTION 107 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 LCD901 8-753-050-67 ACX309AK-1 6-3, 6-1-4. BATTERY HOLDER ASSEMBLY BT901 164 158 164 156 not supplied 153 not supplied 163 157 157 not supplied 164 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 1-682-672-11 FP-380 FLEXIBLE BOARD 158 3-071-008-01 SP HOLDER 152 1-815-853-11 CONNECTOR, MEMORY STICK 159 A-7074-973-A DD-163 BOARD, COMPLETE 153 3-695-653-01 SCREW (1.7X3), TAPPING (B) 160 3-071-014-01 SHEET (DD), INSULATING 154 X-3951-967-1 HOLDER ASSY, BATTERY (SILVER) 161 3-071-015-01 SHEET (LED), ADHESIVE 154 X-3951-991-1 HOLDER ASSY (560), BATTERY (BLUE) 162 3-071-013-01 SP CUSHION 155 3-071-027-01 LID, BT (SILVER) 163 3-071-005-01 DD SPACER 155 3-071-027-11 LID, BT (BLUE) 164 3-713-791-71 SCREW (M1.7X4) 156 X-3951-971-1 FRAME ASSY, BT MAIN BT901 1-694-854-11 BATTERY TERMINAL BOARD 157 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 6-4,

CD-340

6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service. mark 0 or dotted line with mark 0 are critical for safety. fied in the diagrams or the components used Some delay should be anticipated when order- Replace only with part number on the set. ing these items. specified. • -XX and -X mean standardized parts, so they • SEMICONDUCTORS µ Les composants identifiés par unemay have some difference from the original In each case, u: , for example: marque 0 sont critiquens pour la one. uA.: µA.uPA.: µPA.sécurité. • RESISTORS uPB.: µPB.uPC.: µPC.Ne les remplacer que par une pièce All resistors are in ohms. uPD.: µPD.portant le numéro spécifié. METAL: Metal-film resistor. • CAPACITORS METAL OXIDE: Metal oxide-film resistor. uF: µF When indicating parts by reference F: nonflammable • COILS number, please include the board. uH: µH • Abbreviation AUS : Australian model J : Japanese model CN : Chinese model JE : Tourist model CND : Canadian model KR : Korea model HK : Hong Kong model Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark CD-340 BOARD, COMPLETE *********************** (Ref. No.: 2,000 Series) Note: The parts mounted on this board are not supplied individually for service. These are included in the LENS BLOCK ASSY (A-7031-343-A).

Electrical parts list of the DD-163 board is

not shown.

Pages 6-6 to 6-8 are not shown.

6-5,

ST-67 SW-364

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-974-A ST-67 BOARD, COMPLETE A-7074-987-A SW-364 BOARD, COMPLETE ********************* ********************* (Ref. No.: 3,000 Series) (Ref. No.: 2,000 Series) 0 1-476-678-21 FLASH UNIT < SWITCH > 3-068-578-01 SENSOR TABLE B 3-071-032-01 TABLE, SENSOR S201 1-771-039-31 SWITCH, PUSH (LENS COVER OPEN/CLOSE) 3-071-033-01 HOLDER, LED < BATTERY > BT101 1-528-999-31 BATTERY, LITHIUM SECONDARY Electrical parts list of the SY-73 board is not < CAPACITOR > shown.

Pages 6-10 to 6-15 are not shown.

C003 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C005 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V 0C008 1-165-806-11 ELECT 120UF 310V 0C010 1-137-723-21 CERAMIC CHIP 0.047uF 10% 250V < CONNECTOR > CN102 1-778-596-21 CONNECTOR, BOARD TO BOARD 30P < DIODE > D001 8-719-056-23 DIODE MA2S111- (K8).SO 0D002 8-719-083-17 DIODE HAU140C029TP D101 6-500-102-01 DIODE TLOH20TP (SONY2) (SELF TIMER/AF ILLUMINATOR (RED)) < COIL > 0L002 1-424-770-11 COIL, TRIGGER < TRANSISTOR > Q005 8-729-422-87 TRANSISTOR 2SB1073-R 0Q011 8-729-053-74 TRANSISTOR CY25AAJ-8-T13 Q012 8-729-039-61 TRANSISTOR TPS613-BC (BRIGHT LEVEL SENSOR) < RESISTOR > R005 1-216-805-11 METAL CHIP 47 5% 1/16W R006 1-216-838-11 METAL CHIP 27K 5% 1/16W R009 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R010 1-216-814-11 METAL CHIP 270 5% 1/16W R016 1-216-805-11 METAL CHIP 47 5% 1/16W R017 1-216-857-11 METAL CHIP 1M 5% 1/16W 0R018 1-216-121-11 RES-CHIP 1M 5% 1/10W R102 1-216-803-11 METAL CHIP 33 5% 1/16W < TRANSFORMER > 0T001 1-435-741-21 TRANSFORMER, DC-DC CONVERTER The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-69 ber specified. portant le numéro spécifié., Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

ACCESSORIES

************ 0 1-476-332-11 ADAPTOR, AC (AC-LSI) (US, CND, JE, J) 0 1-476-332-21 ADAPTOR, AC (AC-LSI) (CN) 0 1-476-332-31 ADAPTOR, AC (AC-LSI) (KR) 0 1-476-332-41 ADAPTOR, AC (AC-LSI) (E, HK, AUS) 0 1-569-007-11 ADAPTOR, CONVERSION (E, JE) 0 1-569-008-21 ADAPTOR, CONVERSION 2P (E) 0 1-575-131-11 CORD, POWER (E) 0 1-696-819-11 CORD, POWER (AUS) 1-757-293-11 CORD, CONNECTION (USB 5P) 0 1-769-608-11 CORD, POWER (E) 0 1-776-985-11 CORD, POWER (KR) 0 1-782-476-11 CORD, POWER (CN) 0 1-783-374-11 CORD, POWER (HK) 1-783-738-31 CORD, CONNECTION (A/V CONNETION 1.5m) 0 1-790-107-22 CORD, POWER (US, CND) 0 1-790-732-11 CORD, POWER (JE, J) 3-065-665-01 MANUAL, INSTRUCTION (for SAFETY) (JAPNESE) (J) 3-066-676-01 SPVD-004 (P) (CD-ROM) (E, HK, KR, AUS, CN, JE) 3-066-677-01 SPVD-004 (I) (CD-ROM) (US, CND, J) 3-068-191-01 PC INSTRUCTION MANUAL (JAPANESE) (J) 3-068-699-01 STRAP, HAND (US, CND, E, HK, KR, AUS, CN, JE) 3-070-841-01 STRAP, HAND (J) 3-070-845-01 REGISTRATION (CD-ROM) (J) 3-070-926-01 MANUAL, INSTRUCTION (JAPANESE) (J) 3-070-926-11 MANUAL, INSTRUCTION (ENGLISH) (US, CND, E, HK, AUS, CN, JE) 3-070-926-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) (CND, JE) 3-070-926-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (E, JE) 3-070-926-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CN, JE) 3-070-926-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (JE) 3-070-926-71 MANUAL, INSTRUCTION (ARABIC) (E) 3-070-926-81 MANUAL, INSTRUCTION (KOREAN) (KR, JE) A-7096-900-A CLUB 2 (JA) ASSY, PICTURE PARADISE (J) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-61-67 E ber specified. portant le numéro spécifié., FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME with a For NTSC mode clear sheet for use. R-Y R MG

YE

B-Y

B CY G

✄ DSC-P3 – 119 – ✄,

Sony EMCS Co. 2001L0500-19-929-913-32 © 2001. 12

– 120 – Published by DI Customer Center,

DSC-P3 US Model Canadian Model SERVICE MANUAL E ModelHong Kong Model Level 2 Australian Model Chinese Model

2001. 12 Korea Model

Tourist Model Japanese Model SUPPLEMENT-1

File this supplement with the service manual. (PV01-040) • Change of Lens Block Assy. SERVICE NOTE • NOTE FOR REPAIR [Note in Lens Frame Installation] When tightening a screw, have both sides of the lens block assembly so as not for the load to depend. Lens frame Lens block assembly M1.7 × 4 M1.7 × 4,

SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

CD-340 (CCD IMAGER) SCHEMATIC DIAGRAM

1234567

CD-340 BOARD A CCD IMAGER(CCD BLOCK)

-REF.NO.:2,000 SERIES- XX MARK:NO MOUNT Note:voltage and waveforms of parts mounted on CD-340 board cannot be measured because they are(mounted)by the side of the lens. R505

B C5073300 XX C50610p

Q502 2SC4250(T5LSONY1) C503 0.1u R506 BUFFER

IC501

LND521 21 GND 16V 0 CCD IMAGER LND520 20 CCD_OUT LND519 19 GND LND518 18 GND LND517 17 V3B LND516 16 V3A

C LND515 15 V4

LND514 14 V1B 10987654321LND513 13 V1A SY-73 BOARD (1/11) LND512 12 V2 CN101 TH501 LND511 (SEE PAGE 4-15) 11 CCD_TEMP_AD (CCD TEMP SENSOR) LND510 10 VSHT LND509 9 VSUB_CONT 11 12 13 14 15 16 17 18 19 20

D LND508 8 GNDLND507 7 CAM_-7.5V C504

LND506 6 CAM_15V 0.1u R501 120 16V R503 LND505 475 GND LND504 4 H2 R504 LND503 1M C5083 RG 0.1u LND502 16V2 H1 C501XX LND501 1 GND C509

E 10u R50216V C5050.1u 2700

16V C502 0.1u SIGNAL PATH 16V VIDEO Q501UN9213J-(K8).SO SIGNAL SWITCH

F Y/CHROMA REC Precautions for Replacement of CCD Imager

• The CD-340 board mounted as a repair part is not equipped with a CCD imager.

When replacing this board, remove the CCD imager from the

old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts

nor exposed to strong light. – 2 –

VOUT VDD GND RG TEST

H2

TEST

H1 V1B

GND

V1A

SUB

V2

CSUB

V3B

VL

V3A H1 V4 H2 IC501 ICX262AQF-13,

SECTION 5 ADJUSTMENTS

1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts replacement replacement Adjustment section Adjustment Initialization of B, D, Initialization of D page datazzE, F, 7, 9 page data Initialization of B, E, F, 7, 9 page datazzVideo Video sync level adj. zzzzVideo burst level adj. zzzzHall adj. zzzzzCamera Flange back adj. zzzzFNo. standard data inputzzzzMechanical shutter adj. zzzzLight value adj. zzzzzAuto white balance standard data inputzzzzzAuto white balance adj. zzzzzColor reproduction adj. zzzzzCCD (white and black) defect compensationzzzStrobe white balance adj. zzzzzzLCD LCD initial data inputzzVCO adj. zzzzBlack limit adj. zzzzBright adj. zzzzContrast adj. zzzzColor adj. zzzzPSIG adj. zzzzVG center adj. zzzzV-COM adj. zzzzzWhite balance adj. zzzzzzSystem control Battery down adj. z z Table 5-1-1 – 3 – Video lens Flash unit LCD block LCD901 (LCD panel) LCD block D9001 (Back light unit) CD-340 board IC501 (CCD imager) SY-73 board IC102 (S/H, AGC, A/D) SY-73 board IC506 (EVR) SY-73 board IC601 (VIDEO AMP) SY-73 board IC801 (LCD drive) SY-73 board IC804 (LCD Timing generator) SY-73 board IC802 (EVR) ST-67 board (COMPLETE) SY-73 board (COMPLETE) SY-73 board IC503 EEPROM,

SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS 6-1-3. LENS BLOCK AND LCD SECTION not supplied % 104 106 LCD901not supplied (Note 1) 102 not supplied 102 D901not supplied 101 116 IC501 (Note 2) 109 ! : BT101 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-40.) (Note 2) Be sure to read “Precuations for Replacement of 102 CCD Imager” on page 2 in this supplement manual when changing the CCD imager. (Note 1) Refer to page 1 when installing the lens The components identified by Les composants identifiés par une frame to the lens block assembly. mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 A-7078-018-A SY-73 BOARD, COMPLETE (SERVICE) 112 A-7074-987-A SW-364 BOARD, COMPLETE 102 3-713-791-71 SCREW (M1.7X4) 113 3-071-123-01 HOLDER, LENS 103 3-071-017-01 SHEET (STROBOSCOPE), INSULATING 114 1-758-667-11 FINDER, OPTICAL (HE01) 104 A-7074-974-A ST-67 BOARD, COMPLETE 115 3-713-791-11 SCREW (M1.7X5), TAPPING, P2 105 3-071-035-01 FRAME, LENS (Note 1) 116 3-054-555-01 RUBBER (K), SEAL 106 3-071-020-01 SHEET (LCD), LIGHT INTERCEPTION 117 A-7074-975-A CD-340 BOARD, COMPLETE 107 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 118 1-758-441-11 FILTER BLOCK, OPTICAL 108 3-071-016-01 SHEET (DD FLEXIBLE), PROTECTION 0D901 1-476-931-11 BLOCK LIGHT GUIDE PLATE (1.5) 109 1-758-666-11 LENS, VIDEO (29WB) IC501 A-7031-345-A CCD BLOCK ASSY (Note 2) 110 3-064-216-01 CUSHION (L) LCD901 8-753-050-67 ACX309AK-1 111 3-064-215-01 SCREW (M1.7), STEP – 4 –,

CD-340

6-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Remark A-7074-975-A CD-340 BOARD, COMPLETE *********************** (Ref. No.: 2,000 Series) (IC501 is not included in this complete board) < CAPACITOR > C502 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C503 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C504 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C505 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C506 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C508 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C509 1-135-957-91 TANTAL. CHIP 10uF 20% 16V < IC > IC501 A-7031-345-A CCD BLOCK ASSY (CCD IMAGER) (Note) < TRANSISTOR > Q501 8-729-037-74 TRANSISTOR UN9213J- (K8).SO Q502 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1) < RESISTOR > R501 1-216-810-11 METAL CHIP 120 5% 1/16W R502 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R503 1-216-805-11 METAL CHIP 47 5% 1/16W R504 1-216-857-11 METAL CHIP 1M 5% 1/16W R505 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R506 1-216-864-11 METAL CHIP 0 5% 1/16W < THERMISTOR > TH501 1-810-816-11 THERMISTOR, NTC (1608) (Note) Be sure to read “Precuations for Replacement of CCD Imager” on page 2 in this supplement manual when changing the CCD imager. 9-929-913-81 Sony EMCS Co. 2001L0500-1© 2001. 12 – 5 – Published by DI Customer Center,

Reverse 992991333.pdf Revision History

S.M. Rev. Ver. Date History Contents issued 1.0 2001.09 Official Release — — 1.1 2001.11 Correction S.M. correction : Page 5-2, Page 5-19, Yes (C1) Page 5-34, Page 5-35, Page 5-36 1.2 2001.12 Supplement-1 • Change of lens block assy. No (S1 PV01-040)]
15

Similar documents

Table for differences of function
DSC-P30/P50 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Hong Kong Model Ver. 1.2 2001. 08 Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P30/P50 Photo: DSC-P50 Argentina Model Brazilian Model DSC-P50 This service manual contains information f
Table for differences of function
DSC-P30/P50 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Hong Kong Model Ver 1.3 2001. 11 Australian Model Chinese Model Korea Model Tourist Model Japanese Model DSC-P30/P50 Photo: DSC-P50 Argentina Model Brazilian Model DSC-P50 This service manual contains information fo
SECTION 1 SERVICE NOTE
DSC-P32 LEVEL 2 SERVICE MANUAL US ModelCanadian Model AEP Model Ver 1.2 2005. 09 UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Japanese Model SUPPLEMENT-2 File this supplement-2 with the service manual. (PV05-051) • Addition of SERVICE NOTE (Notice for CCD
WARNING If you have any questions about this product, you may call: Declaration of Conformity
DSC-P32 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 02 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at th
WARNING If you have any questions about this product, you may call: Declaration of Conformity
DSC-P32 SERVICE MANUAL LEVEL 1 US Model Ver 1.1 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at th
For the Customers in the U.S.A. If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the “Memory Stick”
DSC-P41/P43 SERVICE MANUAL LEVEL 1 DSC-P41 Ver 1.0 2004.04 US Model Revision History DSC-P43 Hong Kong Model Tourist Model Japanese Model DSC-P41/P43 Canadian Model AEP Model UK Model E Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Photo: DSC-P43 Link SPECIFICATION
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.2 2001. 12 Hong Kong Model Australian Model Chinese Model Korea Model
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.2 2001. 12 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.4 2002. 06 Hong Kong Model Australian Model Chinese Model Korea Model
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.4 2002. 06 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.5 2003. 01 Hong Kong Model Australian Model Chinese Model Korea Model
DSC-P5 SERVICE MANUAL US ModelCanadian Model Level 2 AEP Model UK Model E Model Ver 1.5 2003. 01 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. When the machine needs to be repaired, please
CAUTION You are cautioned that any changes or For the Customers in the U.S.A. Notice on the supplied battery
DSC-P52 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
CAUTION You are cautioned that any changes or For the Customers in the U.S.A. Notice on the supplied battery
DSC-P52 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
CAUTION You are cautioned that any changes or For the Customers in the U.S.A. Notice on the supplied battery
DSC-P52 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at t
DSC-P7 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-P7 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 06 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS RE
DSC-P7 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2002. 10 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-P7 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2002. 10 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the
DSC-P7 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 06 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-P7 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2002. 06 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the
Note: This equipment has been tested and found to For the Customers in the U.S.A.
DSC-P73 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.04 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMEN
Note: This equipment has been tested and found to For the Customers in the U.S.A.
DSC-P73 SERVICE MANUAL LEVEL 1 US Model Ver 1.1 2005.05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Photo: Silver Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMEN
DSC-P8 US Model SERVICE MANUAL Canadian Model AEP Model E Model Hong Kong Model Australian Model Chinese Model Korea Model CORRECTION-1 Tourist Model
DSC-P8 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.1 2003. 06 UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model CORRECTION-1 Tourist Model We will inform you that there are printing errors Japanese Model in the service manual previously issued. • Correcti
DSC-P8 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model
DSC-P8 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2003. 03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS RE
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2003. 06 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS RE
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-P8 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.10 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REP
DSC-P9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 04 Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model
DSC-P9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 04 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS AD
For the Customers in the U.S.A. Notice on the supplied battery Certain countries may regulate disposal of the battery used to power this product.
DSC-P92 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUA
Note: This equipment has been tested and found to For the Customers in the U.S.A.
DSC-P93 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUA
DSC-R1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005.10 Canadian Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model
DSC-R1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005.10 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS ACCESSORIES INSTRUCTION MANUAL SERVICE NOTE The components identified by Les c
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2005.11 Canadian Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2005.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link FRAME SCHEMATIC DIAGRAM PRINTED WIRING BOARDS REPAIR PARTS LIST SCH
DSC-R1 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005.10 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.2 2006.05 Canadian Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.2 2006.05 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link FRAME SCHEMATIC DIAGRAM PRINTED WIRING BOARDS REPAIR PARTS LIST SCH
SAFETY-RELATED COMPONENT WARNING!!
DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.3 2004. 07 Photo: DSC-S30 SPECIFICATIONS System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚C to 40˚C) (–20˚C to +60˚C) Minij