Download: DSC-P9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 04 Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model

DSC-P9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 04 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS ADJUSTMENTS DISASSEMBLY SCHEMATIC DIAGRAMS REPAIR PARTS LIST • For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (992997341.pdf). • This service manual contains information for Japanese model as well. • Note in Lens Frame Installation. On the JK-226, JK-227, SY-77 boards SY-77 board This servic...
Author: Acal1978 Shared: 8/19/19
Downloads: 425 Views: 909

Content

DSC-P9 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2002. 04 Canadian Model

Revision History AEP Model

UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS ADJUSTMENTS DISASSEMBLY SCHEMATIC DIAGRAMS REPAIR PARTS LIST • For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (992997341.pdf). • This service manual contains information for Japanese model as well. • Note in Lens Frame Installation. On the JK-226, JK-227, SY-77 boards SY-77 board This service manual procides the information that is premised Schematic diagram ... Pages 4-9 to 4-28 the circuit board replacement service and not intended repair Printed wiring board ... Pages 4-43 to 4-46 inside the JK-226, JK-227, SY-77 boards. Electrical parts list ... Pages 6-9 to 6-13 Therefore, schematic diagram, printed wiring board and electrical parts list of the JK-226, JK-227, SY-77 boards are not JK-226, JK-227 boards shown. Schematic diagram ... Pages 4-33 to 4-34 The following pages are not shown. Printed wiring board ... Pages 4-49 to 4-50 Electrical parts list ... Pages 6-6 The above-described information is shown in service manual Level 3.

DIGITAL STILL CAMERA

,

COVER SPECIFICATIONS System Output connectors AC-LS1A AC power adaptor

Image device 8.98 mm (1/1.8 type) color A/V OUT (MONO) jack Power requirements CCD Minijack AC 100 – 240 V, 50/60 Hz Primary color filter Video: 1 Vp-p, 75 Ω, unbalanced, Rated output voltage Total pixels number of camera sync negative DC 4.2 V, 1.5 A Approx. 4 130 000 pixels Audio: 327 mV (at a 47 kΩ load) Output impedance 2.2 k Operating temperature rangeLens 3× zoom lens Ω 0° to +40°C (32° to +104°F) f=8−24.0 mm (5/ 1516 − /16 inches) USB jack mini-B Storage temperature range (35 mm camera conversion: 39 to 17 19 20° to +60°C (4° to +140°F)117mm (1 /32 − 4 /32 inches)) LCD screen F2.8−5.6 Dimensions 105 × 36 × 56 mm (4 1/4 × 1 7/16 × LCD panel used 2 1/4 inches) (W/H/D, protruding 3.8 cm (1.5 type) TFT drive parts not included)

Camera Total number of dots Mass Approx. 180 g (6 oz)

Effective pixels number of camera 123 200 (560×220) dots (adaptor only) Approx. 3 950 000 pixels Exposure control Power, general NP-FC10 battery pack Automatic, Scene selection (three modes) Used battery pack Used battery Lithium ion battery NP-FC10 White balance Maximum voltage Automatic, Daylight, Cloudy, Power requirements DC 4.2 V Fluorescent, Incandescent 3.6 V Nominal voltage Data formats Movies: MPEG1 (Monaural) Power consumption (when shooting) DC 3.6 V Still images: JPEG, GIF (for Clip 1.9W Capacity 2.4 Wh (675 mAh) Motion) Operating temperature range Audio with still image: MPEG1 0° to +40°C (32° to +104°F) Accessories (Monaural) Storage temperature range • A/V connecting cable (1) Recording media 20° to +60°C (4° to +140°F) “Memory Stick” • NP-FC10 battery pack (1)Dimensions 114 × 51.5 × 35.8 mm Flash Recommended distance (4 1/ × 2 × 1 3/ inches) • AC-LS1A AC power adaptor (1)2 8 0.5 to 3.8 m (1.6 to 12.5 ft) (W) (W/H/D, protruding portions not • Power cord (mains lead) (1) 0.6 to 2.4 m (2 to 7.9 ft) (T) included) • USB cable (1) (when ISO sensitivity is set to Auto) Mass 206 g (7 oz) (NP-FC10 battery pack, • Wrist strap (1) “Memory Stick” and wrist strap • “Memory Stick” (16MB) (1) included) • CD-ROM (USB driver: SPVD-008) (1) Microphone Electret condenser microphone • Operating Instructions (1) Speaker Dynamic speaker Design and specifications are subject to change without notice. — 2 —, SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. Flexible Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page Section Title Page 1. SERVICE NOTE ························································ 1-1 1-2-2. Initialization of B, E, F, 7, 9 Page Data ··························· 5-9 Self-diagnosis Display ····················································· 1-3 1. Initializing B, E, F, 7, 9 Page Data ·································· 5-9 2. Modification of B, E, F, 7, 9 Page Data. ·························· 5-9 2. DISASSEMBLY 3. B Page Table ···································································· 5-9 2-1. BT Lid ············································································· 2-2 4. E Page Table ···································································· 5-9 2-2. Cabinet (Front) Assembly ··············································· 2-2 5. F Page Table ·································································· 5-10 2-3. Cabinet (Rear) Assembly ················································· 2-3 6. 7 Page Table ··································································· 5-12 2-4. LCD Module ···································································· 2-3 7. 9 Page Table ··································································· 5-12 2-5. Cabinet (Bottom) Assembly ············································ 2-4 1-3. Video System Adjustments ············································ 5-13 2-6. Lens Block Assembly ······················································ 2-4 1. Video Sync Level Adjustment ······································· 5-13 Service Position (SY-77 Board: Side A) ·························· 2-5 2. Video Burst Level Check ··············································· 5-13 2-7. Control Switch Block ······················································ 2-5 1-4. Camera System Adjustments ·········································5-14 2-8. SY-77 Board ···································································· 2-6 Data Setting During Camera System Adjustments ········ 5-14 2-9. Memory Stick Connector ················································ 2-6 Picture Frame Setting ···················································· 5-15 2-10. ST-70 Board ····································································· 2-7 Check on the Oscilloscope ············································ 5-15 2-11. SW-368 Board ································································· 2-7 1. Flange Back Adjustment 2-12. JK-227 Board ·································································· 2-8 (Using the minipattern box) ·········································· 5-16 Service Position (SY-77 Board: Side B) ·························· 2-8 2. Flange Back Adjustment 2-13. Circuit Boards Location ·················································· 2-9 (Using the flange back adjustment chart) ······················ 5-17 3. Flange Back Check ························································ 5-17 3. BLOCK DIAGRAMS 4. F No. Compensation ······················································ 5-18 3-1. Overall Block Diagram ··················································· 3-1 5. Mechanical Shutter Adjustment ···································· 5-18 3-8. Power Block Diagram 1 ················································ 3-15 6. Light Value Adjustment ·················································5-19 3-9. Power Block Diagram 2 ················································ 3-17 7. Mixed Color Cancel Adjustment ··································· 5-19 8. Auto White Balance 3200K Standard Data Input 1 ······ 5-20 9. Auto White Balance 3200K Standard Data Input 2 ······ 5-21 10. Auto White Balance 3200K Standard Data Input 3 ······ 5-21 4. PRINTED WIRING BOARDS AND 11. Auto White Balance 3200K Check ······························· 5-22 SCHEMATIC DIAGRAMS 12. Auto White Balance 5800K Standard Data Input 1 ······ 5-23 4-1. Frame Schematic Diagrams ············································· 4-1 13. Auto White Balance 5800K Standard Data Input 2 ······ 5-24 Frame Schematic Diagram (1/2) ····································· 4-1 14. Auto White Balance 5800K Standard Data Input 3 ······ 5-24 Frame Schematic Diagram (2/2) ····································· 4-3 15. Auto White Balance 5800K Check ······························· 5-25 4-2. Schematic Diagrams ························································ 4-5 16. CCD Linearity Check ···················································· 5-26 CD-397 (CCD IMAGER) ··············································· 4-7 17. Color Reproduction Adjustment ···································· 5-27 SW-368 (1/2) (CONTROL SWITCH) ·························· 4-29 18. CCD White Defect Compensation ································ 5-28 SW-368 (2/2) 19. CCD Black Defect Compensation ·································5-29 (LCD DRIVE, TIMING GENERATOR) ····················· 4-31 20. Strobe White Balance Adjustment ·································5-30 ST-70 (FLASH DRIVE) ··············································· 4-35 21. AF Illumination Check ·················································· 5-32 4-3. Printed Wiring Boards ··················································· 4-39 1-5. LCD System Adjustments ·············································5-33 CD-397 ·········································································· 4-41 1. LCD Initial Data Input ·················································· 5-34 SW-368 ·········································································· 4-47 2. VCO Adjustment (SW-368 Board) ································ 5-34 ST-70 ············································································· 4-51 3. Black Limit Adjustment (SW-368 Board) ·····················5-35 4-4. Waveforms ····································································· 4-54 4. Bright Adjustment (SW-368 Board) ······························ 5-35 4-5. Parts Location ································································ 4-57 5. Contrast Adjustment (SW-368 Board) ·························· 5-36 6. VG Center Adjustment (SW-368 Board) ······················· 5-36 5. ADJUSTMENTS 7. PSIG Gray Adjustment (SW-368 Board) ······················ 5-37 Before Starting Adjustment ······················································· 5-1 8. V-COM Adjustment (SW-368 Board) ··························· 5-37 1-1. Adjusting Items when Replacing 9. White Balance Adjustment (SW-368 Board) ················ 5-38 Main Parts and Boards ···················································· 5-2 5-2. Service Mode ·································································5-39 5-1. Camera Section Adjustments ··········································· 5-3 2-1. Adjusting Remote Commander ·····································5-39 1-1. Preparations Before Adjustment ······································ 5-3 1. Used the Adjusting Remote Commander ······················ 5-39 1-1-1.List of Service Tools ························································ 5-3 2. Precautions upon Using the Adjusting 1-1-2.Preparations ····································································· 5-4 Remote Commander ······················································ 5-39 1-1-3.Discharging of the Flashlight Power Supply ··················· 5-4 2-2. Data Process ·································································· 5-40 1-1-4.Precautions ······································································ 5-6 2-3. Service Mode ·································································5-41 1. Setting the Switch ···························································· 5-6 1. Setting the Test Mode ···················································· 5-41 2. Order of Adjustments ······················································ 5-6 2. Bit Value Discrimination ··············································· 5-41 3. Subjects ··········································································· 5-6 3. Mode Dial Check (1) ·····················································5-41 4. Preparing the Flash Adjustment Box ······························· 5-7 4. Mode Dial Check (2) ·····················································5-41 1-2. Initialization of A, B, D, E, F, 7, 9 Page Data ················· 5-8 5. Switch Check (1) ··························································· 5-41 1-2-1. Initialization of A, D Page Data ······································ 5-8 6. Switch Check (2) ··························································· 5-42 1. Initializing A, D Page Data ·············································· 5-8 7. LED Check ···································································· 5-42 2. Modification of A, D Page Data ······································ 5-8 8. Self Diagnosis Code ······················································ 5-42 3. A Page Table ···································································· 5-8 4. D Page Table ···································································· 5-8 — 4 —, Section Title Page 6. REPAIR PARTS LIST 6-1. Exploded Views ······························································· 6-1 6-1-1.Cabinet (Front) Section ··················································· 6-1 6-1-2.Cabinet (Rear) Assembly ················································· 6-2 6-1-3.Lens Block and LCD Section ·········································· 6-3 6-1-4.Battery Holder Assembly ················································ 6-4 6-2. Electrical Parts List ························································· 6-5 * The color reproduction frame is shown on page 113. — 5 —, COVER SECTION 1

SERVICE NOTE

• NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector. bent at the terminal. It is possible that a wire is snapped. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) [Discharging of the ST-70 flexible board’s charging capacitor (C510)] Discharging the Capacitor Short-circuit between the positive and the negative terminals of The charging capacitor (C003) of the ST-70 flexible board is charged charged capacitor with the short jig about 10 seconds. up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the R:1 kΩ/1 W battery is handled by hand. The electric shock is caused by the (Part code: charged voltage which is kept without discharging when the main 1-215-869-11) power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. 1 kΩ/1 W Capacitor Wrap insulating tape. 1-1, [Precaution on Replacing the Video Lens or the SY-77 [Note in Lens Frame Installation] Board] When tightening a screw, have both sides of the lens block assembly The DSC-P9 uses the position sensor to detect the zoom position. so as not for the load to depend. Accordingly, the zoom position will vary if the position data changes due to the replacement of the video lens or the SY-77 board, thus causing the video lens to collide against the mechanism end when the power is turned off. M1.7 × 4 Though the position data is calibrated at the “Flange Back Adjustment”, add the following work when making an adjustment Lens frame at the replacement of video lens to prevent a collision of video lens. Lens block assembly When Replacing the Video Lens 1) With current video lens assembled, turn the power on, and set the bit value of Bit0 on Page:9, Address:17 to “0” using the adjusting remote commander, then turn the power off. M1.7 × 4 2) Replace the video lens with a new one, turn the power on, and perform the “Flange Back Adjustment”. Thus, new position data will be written. 3) After the “Flange Back Adjustment”, return the bit value of Bit0 on Page:9, Address:17 to “1” using the adjusting remote commander. When Replacing the SY-77 Board 1) Replace the SY-77 board with a new one, set the mode dial to “PLAY”, turn the power on, and set the bit value of Bit0 on Page:9, Address:17 to “0” using the adjusting remote commander, then turn the power off. 2) Set the mode dial to “CAMERA”, turn the power on, and perform the “Flange Back Adjustment”. Thus, new position data will be written. 3) After the “Flange Back Adjustment”, return the bit value of Bit0 on Page:9, Address:17 to “1” using the adjusting remote commander. 1-2, [Description on Self-diagnosis Display] Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. 1-3E,

COVER SECTION 2 DISASSEMBLY

• This set can be disassembled in the order shown below. 2-1. BT LID DSC-P9 (Page 2-2) 2-2. CABINET (FRONT) 2-3. CABINET (REAR) 2-4. LCD MODULE ASSEMBLY (Page 2-2) ASSEMBLY (Page 2-3) (Page 2-3) 2-7. CONTROL SWITCH 2-5. CABINET (BOTTOM) BLOCK (Page 2-5) ASSEMBLY (Page 2-4) 2-6. LENS BLOCK ASSEMBLY SERVICE POSITION (Page 2-4) (SY-77 BOARD: side A) (Page 2-5) 2-8. SY-77 BOARD (Page 2-6) 2-9. MEMORY STICK 2-10. ST-70 BOARD CONNECTOR (Page 2-6) (Page 2-7) 2-11. SW-368 BOARD (Page 2-7) 2-12. JK-227 BOARD (Page 2-8) SERVICE POSITION (SY-77 BOARD: side B) (Page 2-8) 2-1, Note: Follow the disassembly procedure in the numerical order given. 2-1. BT LID 1 Open the BT lid. 4 BT lid 2 Screw (1.7 × 3) 3 Two claws 2-2. CABINET (FRONT) ASSEMBLY 6 Screw (M1.7) 1 Screw (M1.7) 2 Screw (M1.7) 7 Center cabinet 5 Cabinet (front) assembly 3 Two screws (M1.7) 2-2, 2-3. CABINET (REAR) ASSEMBLY 2 Screw (M1.7) 5 Cabinet (rear) assembly 1 Screw (M1.7) 3 Two screws (M1.7) 2-4. LCD MODULE 1 Flexible board (CN102) 6 LCD module 2 Flexible board (CN101) 3 Two screws (M1.7) 4 Four claws 5 Back light unit 2-3, 2-5. CABINET (BOTTOM) ASSEMBLY 1 Claw Rear side 2 Cabinet (bottom) assembly 2-6. LENS BLOCK ASSEMBLY 2 Two claws 3 Lens block assembly 1 Two flexible board (CN001, 301) 2-4, [SERVICE POSITION (SY-77 BOARD: SIDE A)] Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate Adjusting remote the adjustment remote commander. commander Lens block assembly SY-77 board CPC-9 jig (J-6082-393-C) 1 18 Color monitor Regulated power supply (6.0 to 7.2 Vdc) LCD module Base Back light unit AC power AC IN adaptor 2-7. CONTROL SWITCH BLOCK 1 Mode dial cover 3 Claw 2 Screw (M1.7) 6 Control swith block 5 Flexible board (CN704) 2-5, 2-8. SY-77 BOARD 5 Claw 1 Connector (CN351) 7 SY-77 board 4 Screw (M1.7 × 4) 2 Flexible board (CN703) 6 Flexible board 3 Three flexible boards (CN701) (CN001, 301, 702) 2-9. MEMORY STICK CONNECTOR 1 Two screws (M1.7 × 4) 2 Claw 3 Memory stick connector 2-6, 2-10.ST-70 BOARD Note: High-voltage cautions 3 ST-70 board (See page 1-1). Note: When installing ST-70 board, the claw is put into the bottom 1 Connector the BT main frame. (CN351) BT main frame 2 Claw 2-11.SW-368 BOARD 1 Two screws (M1.7 × 4) 2 SW-368 board 2-7, 2-12.JK-227 BOARD 6 Claw 2 Claw 7 JK-227 board (including JK-226) 5 Screw (M1.7) 3 Claw 1 Screw (M1.7 × 4) 4 DD sheet metal [SERVICE POSITION (SY-77 BOARD: SIDE B)] Adjusting remote commander Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate CPC-9 jig the adjustment remote commander. (J-6082-393-C) Color monitor Regulated power supply SW-368 board (6.0 to 7.2 Vdc) AC power LCD module AC INadaptor SY-77 board JK-227 board 1 Back light unit ST-70 board Memory stick connector Mode dial block assembly Lens block assembly Base 2-8, 2-13.CIRCUIT BOARDS LOCATION SW-368 ST-70 CD-397 SY-77 JK-227 (including JK-226) Board Name Function CD-397 CCD IMAGER SY-77 CAMERA MODULE, CAMERA DSP, VIDEO, MEMORY, LENS DRIVE, SH DSP, FLASH MEMORY, FRONT CONTROL, AUDIO, CLOCK GENERATOR, FLASH CONTROL, DC/DC CONVERTER, CAMERA PROCESS ST-70 FLASH DRIVE SW-368 CONTROL SWITCH, LCD DRIVE, TIMING GENERATOR JK-227 JACK (including JK-226) 2-9E,

COVER

3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM POWER BLOCK DIAGRAM 2 POWER BLOCK DIAGRAM 1,

COVER SECTION 3 3. BLOCK DIAGRAMS BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-77 BOARD CD-397 BOARD (1/2) PANEL UNIT

LENS IRIS METER SW-368 BOARD (1/2) IC101 CCD OUT PANEL R PANEL R VR DATA BUS 14 CCD IMAGER PANEL G PANEL G IC101 VG LCD901 PANEL B PANEL B LCD DRIVE VB IC151 (2/2) CV OUT SHUTTER ZOOM FOCUS IRIS CAMERA COLOR MOTOR MOTOR MOTOR MOTOR H1, H2 MODULE LCD V1A, V1B, V2 (1/10)

MONITOR MMMMV3A, V3B, V4 IC102

LCD TIMING LENS ZOOM VSUB CONT GENERATOR TEMP POSITION ZOOM FOCUS ADDRESS BUS14 IC602 IC505 (2/2) SENSOR SENSOR SENSOR SENSOR 256M EEPROM D901 SDRAM (6/10) BACK LIGHT DATA BUS 32 (3/10) IC508

EVR

(D/A CONVERTER) IC302 LCD SO, XLCD SCK(6/10) IC601 (4/10) IC501

CAMERA

FOCUS MOTOR HR DIR0A, HR DIR0B, HR EN0 MC CAM,DSP DRIVER SH DSP(2/10) 25 25 (5/10) ZOOM MOTOR HR DIR1A, HR DIR1B, HR EN1 DRIVER IRIS M IN, IRIS M EN, 16 16 MS DIO, MS BS, MS SCLK MS IRIS IRIS S IN, IRIS S EN SOCKET DRIVER MSHUT ON 20 IC504 SHUTTER DRIVER MSHUT EN 16M FLASH JK-227 BOARD (2/2) JK-226 BOARD (2/2) 16 (6/10) XFC RST SENS IC101 V OUT J002 VIDEO AMP XZM RST SENS VAMP ON (3/10) AU OUT A/V OUT AU AINL (MONO) ZOOM POS STRB ON AU AOUT LENS TEMP ZOOM POS USB D+ USB D+ CN002 LENS TEMP USB D− USB D– USB

CD-397 BOARD (2/2)

SP VOL D101 AU AINL IC201 SELF TIMER/ SELF TIMER LED AU AOUT SP901AUDIO AMP AF ILLUMINATOR SPEAKERBEEP, BEEP ON (8/10) X501 IC507 TG CLK MIC901 27MHz CLOCK GEN. USB CLK

MICROPHONE ST-70 BOARD (1/2)

T001 (6/10) MC CLK Q360, 361 CHARGING ST-70 BOARD (2/2) CAPACITOR ACV UNREG BEEP, BEEP ON RESET IC403 BT001STB CHARGE FLASH INITIAL RESET, LITHIUM UNIT XSTB FULL SELF TIMER LED EVER 3.0V BACK UP VCC FR 5V BATTERY (7/10) Q002 STB CHG XSTB FULL SW-368 BOARD (2/2) KEY AD0, 1 FUNCTION CAM 15V IC401 SWITCH CAM 3.2V FRONT CONTROLLER

JK-227 BOARD (1/2) CAM –7.5V (7/10) KEY AD3 ZOOM

A 4.9V SWITCH A 2.9V + D 1.5V IC001 BT901 D 2.9V BATTERY S DC/DC PANEL 2.9V TERMINAL CONTROL BL VO– (10/10) CONTROL SWITCH BLOCK– FR 5V SYS DD ON MODE DIAL, XPB ON, XSET UP ON MODE

DIAL

UNREG SCK, UNREG SO XPWR ON POWER ON/OFF

JK-226 BOARD (1/2) BATT SIG XAE LOCK SW, XSHTR ON SHUTTER

J001 AVC UNREG SWITCH DC IN BATT UNREG 3-1 3-2 PRELAMP AF ON CAM SO, XCAM SCK ADDRESS BUS DATA BUS CAM SO, XCAM SCK CV OUT LCD SO, XLCD SCK,

COVER 3. BLOCK DIAGRAMS

3-8. POWER BLOCK DIAGRAM 1 ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-77 BOARD (1/2) JK-227 BOARD CN706

J001 JK-226 BOARD HI UNREG CPC CN703 10 DC IN (FOR CHECK) ACV UNREG ACV UNREG1 17 F004 ı BATT/XEXT 24BATT/XEXT Q017, 018 F00337 CONTROL SWITCH BLOCK GND FAST CHARGE CN704 PWR LED VCC 12 (POWER) INIT CHARGE D009 D007 D001 Q015, 021 IC002 D 2.9V D0083D2.9V BATT CHARGE (10/10) 1 CONTROL F001 D006 L016 L017 D010 + BATT UNREG1 UNREG1 ı DC/DC 8 CONVERTER BT901 BATT/XEXT BATTERY BATT SIG BATT SIG BATT SIGS FR 5VTERMINAL 36 – BATT GND GND 9 EVER 3.0V ı DD CON SENS IC001 DC/DC CONTROL (10/10) L019 Q002, 005 L005 L011 VCC2 41 SWITCHING D 1.5V OUT 1p 36 OUT 1n 37 VIN 1– 55

ST-70 BOARD L020 Q003, 006 L006 L007 D 2.9V SWITCHING

T001 CN351 47 RST L008 A 2.9V Q360, 361 4 L351 D407 OUT 4p 30 FLASH ı ST UNREG OUT 4n 31 L009 UNIT PANEL 2.9V8 48 LD ON IC403 EVER 3.0V VIN 4– 5356 VCC1 L021 INITIAL RESET, L401 BACK UP VCC VCC31 VL 3V (7/10) VCC5 20 BT001

LITHIUM

BATTERY L004 Q008, 010 Q012 L012 A 4.9V A POWER 2SWITCHING (PAGE 3-17) IC404 IC003 FRONT CONTROLLER OUT 5p 38 (10/10) (7/10) OUT 5n 39 3.2V CAM 3.2V OUT 5S 43 REG VIN 5– 52 66 DD CON SENS L002 Q009, 011 Q013 L013 68 ACV SENS M 5VSWITCHING 67 BATT SENS FAST CHARGE OUT 6p 2848 FAST CHARGE INIT CHARGE OUT 6n 2947 INIT CHARGE BATT/EXT OUT 6S 18 8 BATT/XEXT VIN 6– 50 Q408 L001 Q007 D002 D013 L014 BATTERY CAM 15VBATT SIG 43 BATT SICHARGE VCC4 19

SWITCHING

DETECTOR 42 BATT SO OUT 9 23 STB CHARGE 46 STB CHG IN 9– 80 SYS DD ON SYS DD ON 76 57 CONT SCP91Q004 XCS DDCON 22 XCS DDCON 44 XCS D004 D005 L010 UNREG SO 20 UNREG SO BL VO– 45 DATA SWITCHING UNREG SCK 21 UNREG SCK 46 CLK Q019, 020 OUT 10 22 –7.5V CAM –7.5V

REG

AMP IN 4 AMP OUT 5 IN 10− 3 Q001 SCPIN 10 EMERGENCYDETECT 3-15 3-16,

COVER 3. BLOCK DIAGRAMS

3-9. POWER BLOCK DIAGRAM 2 ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SW-368 BOARD PANEL UNIT

CN701

SY-77 BOARD (2/2) Q002, 003 L102 Q105, 108 CN10232 CAM15V 13.5V VDD

33 REG 18 D102

VDDG

16 LCD901

COLOR

IC101 CRext XP OFF 14 9 LCD PANEL 2.9V 11 PANEL 2.9V L101 LCD DRIVER Q108 MONITOR 12 D003 (2/2) REF VOLTAGE REF (AE LOCK) GEN D004 (TALLY) L104 IC102 IC103 LCD TIMING BACK LIGHT D002 GENERATOR CONTROL (FLASH/CHG) (2/2) (2/2) EVER 3.0V EVER 3.0V 3 CN101 D901 30 A 4.9V BL THH 6 BACK LIGHT31 BL VO– 1 BL VO– 1 BL L L152 FB1512 IC101

CAMERA

L153 FB153 MODULE (1/10) L154 FB152

CD-397 BOARD

Q152 - 153 CN001FB155 CAM 15V CAM 15V L101 CAM 15V 6 IC101 − − FB154 FB101CAM 7.5V CAM 7.5V CAM −7.5V CCD IMAGER

POWER 1 7

(PAGE 3-16) A A 4.9V A 4.9V M 5V M 5V M 5V D10124 SELF TIMER/ CAM 3.2V CAM 3.2V L504 AF ILLUMINATOR CAM DD ON 198 PTM (6) MS POWER ON 30 D32/PTA (7) FB501 D702 D 2.9V D 2.9V IC501 (MS ACCESS) FB502 D 1.5V D 1.5V MC CAM, SH DSP (5/10) L501 L503 IC508 IC505 FB504 IC507 FB506 IC504 CN702 EVR EEPROM CLOCK GEN. 16M FLASH Q701 (D/A CONV.) (6/10) (6/10) (6/10) 2 VCC MEMORY (6/10) 6 STICK LENS BLOCK Q301 CN301 D 2.9V L303 F RST VCC ZOOM 19 SENSOR A 2.9V A 2.9V Z RST VCC 11 FOCUSSENSOR M 5V L302 IC302 L301 7CH LENS DRIVER Z POSI VCC

ZOOM

14 POSITION L203 (4/10) SENSOR Q302 L201 IC201 AUDIO AMP L202 (8/10) FB603 IC602 L101 IC101 256M VIDEO AMP SDRAM (3/10) (3/10) L602 IC301

BUFFER

FB601 (4/10)IC601 CAMERA DSP L601 (2/10) FB602 3-17 3-18E,

COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAMS12345678910 11 12 13

FRAME (1/2) A PANEL UNIT CONTROLB SWITCH G

6 2 BLOCK

D901 B LCD901A1S004BACK 1.5INCH POWER

S005

LIGHT COLOR MODE DIAL LCD UNIT

1234D001 (POWER (GREEN)) S003 (SHUTTER)

C MIC901 MICROPHONE

CN705 2P 1 MIC_SIG

D 2 REG_GND

CN701 33P 1 BL_VO-

E 2 BL_VO-3 EVER_3.0V

4 KEY_AD0 5 AE_LOCK_LED 6 KEY_AD1 7 XCHARGE_LED

SW-368 BOARD 8 PANEL_HDD

9 XTALLY_LED

F SY-77 BOARD (1/2)10 HDO

11 PANEL_2.9V 12 PANEL_2.9V 13 PANEL_V D702 D002 (MS ACCESS LED (RED)) (STROBO/CHARGE_LED (AMBER)) 14 LCD_SO 15 KEY_AD3 S004 16 XCS_PANEL_TG CONTROL W ZOOM T 17 XLCD_SCK

G D003 S001 S002

S401 18 REG_GND

RESET

(AE_LOCK (GREEN)) 19 REG_GND 20 REG_GND 21 REG_GND 22 REG_GND D004 23 PANEL_R (TALLY (RED)) 24 PANEL_G 25 PANEL_B S003 S005

H 26 REG_GNDMENU DISPLAY

27 PANEL_COM 28 PANEL_VG 29 XRST_SYS 30 A_4.9V 31 A_4.9V 32 CAM_15V 33 CAM_15V

I CPC

(FOR CHECK) 4-1 4-2 FRAME (1/2) CN101 6P BL_THH 6 NC 5 BL_THL 4 BL_H 3 NC 2 BL_L 1 TESTL 24 COM 23 VST 22 VCK 21 EN 20 DWN 19 VDD 18 VSS 17 VDDG 16 VSSG 15 CS 14 WIDE 13 HST 12 REF 11 SDUT 10 CRext 9 HCK2 8 HCK1 7 PSIG6G5R4B3RGT 2 TEST2 1 CN102 24P CN704 14P XPWR_ON 14 NC 13 PWR_LED_VCC 12 XPWR_LED 11 XSET_UP 10 XMOVIE 9 XPB_ON 8 CN706 18P NC71N.C GND62N.C NC53N.C MODE_DIAL44REG_GND D_2.9V35CPC_IN XSHTR_SW26N.C XAE_LOCK_SW17HSY 8 PANEL_COM 9 VG 10 HI_UNREG 11 LANC_IN 12 LANC_OUT 13 N.C 14 N.C 15 N.C 16 N.C 17 N.C 18 N.C,

COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS

12345678910 11 12 13 14 15

FRAME (2/2)

CN001 25P

A PRE_LAMP 25 LENZ UNIT

M_5V 24

ST-70 BOARD GND 23CN351 15P

GND 22 OPTICAL 1 VL_3V VIEW GND 21 FINDER 2 STB_ON1 CCD_OUT 20 3 STB_FULL LENZ GND 19 4 ST_UNREG

B GND 185 ST_UNREG D101

V4 17 SELF TIMER/ 6 ST_UNREG AF ILLUMINATOR V3A 16 7 ST_UNREG V3B 15 8 ST_UNREG V1B 14 9 REG_GND V1A 13

FLASH 10 REG_GND V2 12 CD-397 BOARD CCD

11 REG_GND CCD_TEMP_AD 11 12 REG_GND C003 VSHUT 10

C CHARGING 13 REG_GNDCAPACITOR VSUB_CONT 914 REG_GND

GND 8 15 REG_GND CAM_-7.5V 7 CAM_15V 6 BT001 GND 5 H1 4 LITHIUM BATTERY (BACK UP) RG 3 H2 2

D GND 1 SY-77 BOARD (2/2) CN301 27P

ZOOM_A 27 ZOOM_A 26 ZOOM_B 25 ZOOM_B 24 FOCUS_A 23

E FOCUS_B 22

FOCUS_A 21 FOCUS_B 20 F_RST_VCC 19 F_RST_GND 18 F_RST_SENS 17 Z_POSI_OUT 16 Z_POSI_GND 15

F Z_POSI_VCC 14

TEMP_OUT 13 TEMP_GND 12 Z_RST_VCC 11 Z_RST_SENS 10 Z_RST_GND 9 IRIS_S- 8 IRIS_S+ 7

G IRIS_M- 6

IRIS_M+ 5 SHUTTER- 4 SHUTTER- 3 SHUTTER+ 2 SUTTEER+ 1

H JK-227 BOARD FP-478 FLEXIBLE BOARD USB I JK-226 BOARD MS BT901 SOCKET

A/V OUT BATTERY (MONO) DC IN TERMINAL

SP901 J SPEAKER

J002 J001

FRAME (2/2) 4-3 4-4

CN703 39P 39 SP+ 38 SP- 37 BATT/XEXT 36 BATT SIG 35 USB_JACK_IN 34 USB_DATA- 33 USB_DATA+ 32 AV_JACK_IN 31 V_OUT 30 AU_OUT 29 N.C. 28 USB_GND 27 USB_GND 26 AV_GND 25 AV_GND 24 ACV_UNREG1 23 ACV_UNREG1 22 ACV_UNREG1 21 ACV_UNREG1 CN002 5P 20 ACV_UNREG1 5 GND 19 ACV_UNREG1 4 ID 18 ACV_UNREG1 3 D+ 17 ACV_UNREG1 2 D- 16 GND 1 VCC 15 GND 14 GND 13 GND 12 GND 11 GND 10 GND 9 GND 8 BATT_UNREG1 7 BATT_UNREG1 6 BATT_UNREG1 5 BATT_UNREG1 4 BATT_UNREG1 3 BATT_UNREG1 2 BATT_UNREG1 1 BATT_UNREG1 CN702 8P 1 VSS 2 VCC 3 SCLK 4 INT 5 DIO 6 VCC 7 BS 8 VSS +, COVER 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ

LµiFn. 5k0 V or less are not indicated except for electrolytics Pattern box

and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum L capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Front of the lens Kinds of capacitor Temperature characteristics L = About 30 cm External dimensions (mm) • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. 2. Adjust the distance so that the output waveform of In such cases, the unused circuits may be indicated. Fig. a and the Fig. b can be obtain. • Parts with ★ differ according to the model/destination. H Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ LineABA=BBA• B: B– Line Fig. a (Video output terminal output waveform) • J : IN/OUT direction of (+,–) B LINE. • C: adjustment for repair. • A: VIDEO SIGNAL (ANALOG) • A: AUDIO SIGNAL (ANALOG) • A: VIDEO/AUDIO SIGNAL • A: VIDEO/AUDIO/SERVO SIGNAL • A: SERVO SIGNAL • Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) Fig.b (Picture on monitor TV) • Voltages and waveforms are measured between the measurement points and ground when camera shoots color bar chart of pattern box. They are reference values When indicating parts by reference number, please and reference waveforms. include the board name. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Note : The components identified by mark 0 or Note : Les composants identifiés par une marque dotted line with mark 0 are critical for safety. 0 sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifie. 4-5 Yellow Cyan Green White Magenta Red Blue,

COVER

4-2. SCHEMATIC DIAGRAMS Link CD-397 BOARD (CCD IMAGER) ST-70 BOARD (FLASH DRIVE) SW-368 BOARD (1/2) (CONTROL SWITCH) CONTROL SWITCH BLOCK SW-368 BOARD (2/2) (LCD DRIVE, TIMING GENERATOR) COMMON NOTE FOR SCHEMATIC DIAGRAMS WAVEFORMS,

COVER 4-2. SCHEMATIC DIAGRAMS CD-397 PRINTED WIRING BOARD

4-2. SCHEMATIC DIAGRAMS For Schematic Diagram • Refer to page 4-41 for printed wiring board. 12345678

CD-397 BOARD Note: voltage and waveform of mounted on CD-397 board

can not be measured, because they are (mounted)

A CCD IMAGER(CCD BLOCK) by the side of the lens. XX MARK:NO MOUNT

Q101 2SC4250(T5LSONY1)

BUFFER

D101 TLOH20TP(SONY2) SELF TIMER/ AF ILLUMINATOR LND125 25 PRE_LAMP

B R101LND124 C102 C10624 M_5V 0

XX 0.1u LND123 16V23 CCD_GND LND122 22 CCD_GND R105 C105 3300 10p LND121 21 CCD_GND LND120 20 CCD_OUT LND119 19 CCD_GND LND118 18 CCD_GND LND117 17 V4

C LND116 16 V3A

LND115 15 V3B

SY-77 (1/10) LND114 14 V1B

CN001 LND113 13 V1A 10987654321( PAGE 4-9) LND112 12 V2 LND111 11 CCD_TEMP (CCD TEMP SENSOR) TH101 LND110 10 VSHUT IC101 LND109 9 VSUB_CONT CCD IMAGER

D LND108 8 GND

11 12 13 14 15 16 17 18 19 20 LND107 7 CAM_-7.5V LND106 6 CAM_15V LND105 5 GND R1030 LND104 4 H1 R102 68 C101 0.1u LND103 3 RG LND102 2 H2 R104 LND101 1 GND 0

E C1030.1u R107

16V 220k C108 2200p

SIGNAL PATH FB101

R108

VIDEO 2700C104 C107 SIGNAL 10u 0.1u16V Y/CHROMA C109

0.1u

F REC

R109 Q10205 DTC144EHT2L XX SWITCH

Precautions for Replacement of CCD Imager

• The CD-397 board mounted as a repair part is not equipped with a CCD imager.

When replacing this board, remove the CCD imager from the

old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts

nor exposed to strong light. 4-7 4-8 CD-397

VOUT VDD GND RG TEST

H2

TEST

H1 V1B

GND

V1A R106 22 VSHT V2

CSUB

V3B

VL

V3A H1 V4 H2 IC101 ICX406AQF-13,

COVER 4-2. SCHEMATIC DIAGRAMS SW-368 PRINTED WIRING BOARD For Schematic Diagram

• Refer to page 4-47 for printed wiring board. 12345678910 11

SW-368 BOARD (1/2) A CONTROL SWITCH(KEY BLOCK) S004 XX MARK:NO MOUNT CONTROL NO MARK:REC/PB MODE

UP RIGHT CL001 BL_VO- BL_VO- CL002 BL_VO- R012 BL_VO- 1200 SET CL003 EVER_3.0V DOWN CL004 LEFT R015 KEY_AD0 1500 CL005

B AE_LOCK_LED CL006

KEY_AD1 CL007 XCHARGE_LED R013 1200 CL008 PANEL_HDO PANEL_HDO R018 D004 R009 CL009 470 CL-196HR-CD-T 820 D004 XTALLY_LED TALLY(RED) CL010 HDO HDO R008D003 CL011 2.2 CL-196YG-CD-T 330 D003 R011 R014 PANEL_2.9V AE_LOCK(GREEN) 1500 B1 A1 B1 A1 3300 CL012 PANEL_2.9V 0 D002 R0072121CL013 560PANEL_V SML-310YTT86 D002C PANEL_V STROBO/CHARGE_LED(YELLOW)CL014 LCD_SO Q004 (YELLOW) LCD_SO UN9213J-(K8).SO4343B2 B2 A2 CL015 LED DRIVE A2S003 S005 KEY_AD3WT

SY-77 (6/10) CL016

MENU DISPLAY XCS_PANEL_TG XCS_PANEL_TG CN701 CL017 XLCD_SCK (SEE PAGE 4-20) XLCD_SCK CL018 S001 S002 REG_GND R010 CL019 1200 REG_GND CL020 REG_GND CL021 W ZOOM TD007

D D001REG_GND MAZT082H08S0 MAZT082H08S0CL022

REG_GND CL023 PANEL_R LND001 PANEL_R CL024 PANEL_G STATIC_GND PANEL_G D006 R004 CL025 PANEL_B MAZT082H08S0 D005 XX PANEL_B CL026 MAZT082H08S0 REG_GND CL027 PANEL_COM PANEL_COM CL028 PANEL_VG PANEL_VG CL029

E XRST_SYSXRST_SYS Q003CL030 A_4.9V HN1A01FU-TE85R

A_4.9V B+ SWITCH CL031 A_4.9V 14.5 A_4.9V CL032 2 CAM_15V CL033 15.216CAM_15V PANEL_13.5V13.443R005 100k 14.1 R002 5 33k

F 0.5%SIGNAL PATH 14.1

6 3

VIDEO SIGNAL 13.32513.4 CHROMA C002 1 40.22u R003 Q002

240k 12.9 HN1C01FU-TE85R 0.5% R006 B+ SWITCH

REC 100k

REG_GND

G PB

PANEL_2.9V PANEL_R PANEL_R PANEL_G PANEL_G 1 (2/2) PANEL_B PANEL_B XRST_SYS XRST_SYS

HDO HDO H PANEL_V PANEL_VLCD_SO

LCD_SO XLCD_SCK XLCD_SCK XCS_PANEL_TG XCS_PANEL_TG A_4.9V A_4.9V BL_VO- BL_VO- PANEL_HDO PANEL_HDO

I PANEL_VG PANEL_VGPANEL_COM

PANEL_COM

SW-368 (1/2) 4-29 4-30

,

COVER 4-2. SCHEMATIC DIAGRAMS SW-368 PRINTED WIRING BOARD For Schematic Diagram

• Refer to page 4-47 for printed wiring board. • Refer to page 4-54 for waveforms. 12345678910 11 12 13 14 15 16 17

SW-368 BOARD (2/2) A LCD DRIVE,TIMING GENERATOR(RGB/TG BLOCK)

Q107

NO MARK:REC/PB MODE L102 MCH3310-TL-E10uH 13.4 SWITCH 13.4

S D C110 C111 R127 G 4.7u 0.1u 470k 0 20V C108 R107 R115 0.01u 15k 10 0

B XP_OFF

2.9 0.7 0.5 2.8 0 2.9 1.4 1.5 2.9 7.1 1.7 13.4 C1162.2u 36 35 34 33 32 31 30 29 28 27 26 25 Q105 R135 C123 UN9213J- 150k 0.1u (K8).SO

SWITCHING

R116 CN102 24P PANEL UNIT 1.2 4 7.1 10 24 TEST

C N.C./C_BG 3 VB C117 23 COMXC.SAVE 2.9 1.7 2.2u VST

XC.SAVE B_DC_DET R117 22 VST

VCK

XLCD_SCK 2.9 7.1 10 21 VCK XSCK 2 VG C118 EN2.2u 20 EN XTG_SO 2.2 1.7 DWN SI G_DC_DET R118 19 DWN PANEL_13.5V R106470k XCS_PANEL_TG 2.9 1.7 10 18 VDD L101 C101 47u XCS47uH 6.3V 2.9 IC101 1 VR C119 C122 17 VSS 1.7 2.2u 1u PANEL_2.9V Vcc1 LCD DRIVER R_DC_DET 16 VDDGC103 R119 R120 R122 LCD901

D C102 0.01u 1.2 IC101 100k 100k 100k D102 15 VSSG COLOR0.1u C104 TRAP_ADJ RB5P004AM1 MA8036-TXGND2/N.C. LCD14 CS MONITOR

0.01u 1.2 WIDE R104 LPF_ADJ GND1 13 WIDE 33k R105 HST 33k XP.SAVE 2.9 12 HST C120 C105 XP.SAVE VREF 4.7u R121 11 REF 0.01u 1.8 13.4 100k PANEL_B B_IN 5 Vcc3 10 SDUTC106 0.01u 1.8 9 CRext PANEL_G G_IN COM_OUT HCK2 C107 8 HCK2 0.01u 1.8 6 HCK1

E PANEL_R R_IN COM_IN 7 HCK1

6 PSIG75G4R

HDO

HDO3BPANEL_V RGT PANEL_V12345678910 11 12 2 RGT LCD_SO LCD_SO 2.9 0.9 2.9 0.9 0.9 1.4 1.4 1.4 1.5 2.9 6.7 1 TEST2 XLCD_SCK XLCD_SCK R126

F 1 XCS_PANEL_TGXCS_PANEL_TG 10k

(1/2) Q102 7.7 L104 XP4601-TXE 13.4 47uH R109 R113 R114 PSIG DRIVE 47k 1M 100k467.1 R131 R1345 2 470k 56k R111 C112 R112 7.7 0.5%C109 1u 22k 560p 68k31D101 7.1 REG_GND 1SV290(TPL3) 6.5 7.1

G C115641.50.001u 7.1 2 0.8 Q1085

A_4.9V 2SB1462J- L103 QR(K8).SO 6.8uH Q101 6.5 REF VOLTAGE GEN BL_VO- C114 XP4601-TXE13R13282p PSIG DRIVE 6.5 27k 0.5% R124 10k R139 1k XRST_SYS

H

PANEL_HDO C126 2200p R133 3.0 0.9 2.9 0.9 0.9 2.9 1.4 2.9 1.4 1.4 2.9 R136 R130 68 680.5% PANEL_VG 0.5%36 35 34 33 32 31 30 29 28 27 26 25 10k 0.5% PANEL_COM C121 R125 IC103 1u R123 2200 TC75S55FU(TE85R)I Q1069 0 8200 2SB1462J-BGP 2.8 VST 3.3 4.8 4.8 R128VCC 3300 QR(K8).SO CN101 6P D901 XCLP VST BACK LIGHT 4.0 BACK LIGHT4.0 DRIVE Q109 6 BL_THH PRG 2.9 1.4 VCK 2SB1462J- PRG VCK 3.3 3.9 3.4 3.4 5 N.C.QR(K8).SO BLK 0 2.6 EN Q103 BACK LIGHT 4 BL_THL SBLK EN 2SD2216J- DRIVER137 R138 QR(K8).SO 0.9 3 BL_H FRP 1.4 2.9 DWN 10k 47k BACK LIGHT 0.9 FRP DWN 0.5% DRIVE 2 N.C. PFRP 1.4 0.2 WIDE IC103 R1293300 1 BL_L PFRP IC102 WIDE C125 BACK LIGHT 0.1J XLCD_SCK 2.9 2.9 0.01u CONTROL 2.9 XSCK LCD TIMING GENERATOR VDD 2.9 IC102 0 HST VDD CXD3512R-T4 HST C124 XCS_PANEL_TG 0.01u 2.3 1.4 HCK2 XCS HCK2 Q104 UN9213J-(K8).SO XTG_SO 2.9 1.4 HCK1 BACK LIGHT SO HCK1 DRIVE LCD_SO 2.9 2.9 RGT SI RGT 2.9 XP_OFF

K VDO XP_OFF

PANEL_V 2.9 XVD 10 TSTEN

SIGNAL PATH12345678910 11 12

2.7 0.3 2.9 2.9

VIDEO SIGNAL 8 L CHROMA HDO REC The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que

PB

05 Replace only with part number specified. par une piéce portant le numéro spécifié. 4-31 4-32 SW-368 (2/2) 48 47 46 45 44 43 42 41 40 39 38 37 N.C./R_INJECT XSH.SAVE 48 47 46 45 44 43 42 41 40 39 38 37 SH_R EXT_DA SH_R SH_G N.C SH_G SH_B BGP BGP SH_B XCLR SH_A BLACK_IN BLK HD SH_A SHR SH_R PRG PRG HDO R108 GND/N.C. SH_G 2700SHG FRP FRP XWRT BIAS SHB SH_B PFRP PFRP BL_ON R110 OP_IN+ SHA SH_A 68k XVP.SAVE DETIN OP_IN- VSS VP GND OP_OUT TEST P_DC_DET TST0 C113 VCO RPD 0.1u Vcc2 LED COM_DC XC.SAVE XC.SAVE

PWM OSCI TEST OSCO

TEST 13 14 15 16 17 18 19 20 21 22 23 24 XSTBY XP.SAVE

TEST

13 14 15 16 17 18 19 20 21 22 23 2432145,

COVER 4-2. SCHEMATIC DIAGRAMS ST-70 PRINTED WIRING BOARD

For Schematic Diagram • Refer to page 4-51 for printed wiring board. 12345678910

ST-70 BOARD

D002

A FLASH DRIVE(FL BLOCK) HAU160C030TP LND016 NO MARK:REC/PB MODE XE_A

D001 T001 R007 MA2S111-(K8).SO 1M 1/10W45L001 LND017 R002 C002 0 27k 1u F TRIGGERR004 FLASH 0 270 UNIT Q001

B 0 2SB1073-R-TX S

C003 Q002 TRANS DRIVE 135uF CY25AAJ-8-T13 2 FLASH DRIVE LND018

CHARGING

CAPACITOR 187.6 XE_K

P

R00116C004 R003 R005 0.047u C001 2700

C BT001 0.01uLITHIUM R006

BATTERY 1M (BACK UP) LND001 1 VL_3V LND002 2 STB_ON1 LND003 3 STB_FULL LND004 4 ST_UNREG LND005 5 ST_UNREG LND006 6 ST_UNREG

D SY-77 (9/10) LND007

CN351 7 ST_UNREG (PAGE 4-26) LND008 8 ST_UNREG LND009 9 REG_GND LND010 10 REG_GND LND011 11 REG_GND LND012 12 REG_GND LND013 13 REG_GND LND014 14 REG_GND

E LND015 15 REG_GND

The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que Replace only with part number specified. par une piéce portant le numéro spécifié. 4-35 4-36 ST-70,

DSC-P9 DSC-P9 COVER COVER 4-2. SCHEMATIC DIAGRAMS For Schematic Diagram

12345

CONTROL SWITCH BLOCK A

CONTROL SWITCH BLOCK is replaced as a block, so that PRINTED WIRING BOARD is omitted. S005 MODE DIAL SET_UP

B B G

R002 MOVIE SCN 400062R003 PLAY P_AUTO 6000A1(5 POSITION MODE_DIAL) (1st)

C S003 S004

(SHUTTER) (2nd) POWER R001 20k D001 (POWER(GREEN))

D E SY-77 (7/10)

CN704 05 (SEE PAGE 4-21)

CONTROL SWITCH BLOCK 4-38

14P XAE_LOCK_SW 1 XSHTR_SW 2 D_2.9V 3 MODE_DIAL 4 NC 5 GND 6 NC 7 XPB_ON 8 XMOVIE 9 XSET_UP 10 XPWR_LED 11 PWR_LED_VCC 12 NC 13 XPWR_ON 14, COVER 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR WIRING BOARDS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. (The other layers’ patterns are not indicated) BE123321123321212121654• Through hole is omitted. • Circled numbers refer to waveforms. 12213412344334• There are a few cases that the part printed on diagram isn’t mounted in this model. 5433452143211221• C: panel designation 4-39,

COVER

4-3. PRINTED WIRING BOARDS Link CD-397 BOARD ST-70 BOARD SW-368 BOARD COMMON NOTE FOR PRINTED WIRING BOARDS WAVEFORMS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CD-397 (CCD IMAGER) • For Printed Wiring Board. • :Uses unleaded solder. • There are a few cases that the part isn't mounted in this model is printed on this diagram. SELF TIMER/ AF ILLUMINATOR 4-41 4-42 CD-397, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION

SW-368 (FRONT CONTROL, LCD DRIVE, TIMING GENERATOR, CONTROL SWITCH)

• For Printed Wiring Board. • :Uses unleaded solder. • There are a few cases that the part isn't mounted in this model is printed on this diagram. • See page 4-57 for printed parts location. D004 (TALLY (RED)) D003KKWZOOM T (AE LOCK (GREEN))

A

6 K D002 A AK (STROBO/CHARGE LED) KKA1KK53 4

CONTROL

DISPLAY MENU

SW-368 4-47 4-48

, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION ST-70 (FLASH DRIVE) • For Printed Wiring Board. • :Uses unleaded solder. • There are a few cases that the part isn't mounted in this model is printed on this diagram. FLASH UNIT

C

11, 12BE613254BT001 BATTERY,

A

K LITHIUM SECONDARY

A

11, 12 ST-70 4-51 4-52, COVER SW-368 BOARD SW-368 BOARD167.8 Vp-p 340 mVp-p 2H H IC101 w; REC/PB IC101 rj REC/PB277.8 Vp-p 460 mVp-p 2H H IC101 ws REC/PB IC101 rk REC/PB387.8 Vp-p 3.0 Vp-p 2H H IC101 wf REC/PB IC102 1 REC/PB495.1 Vp-p 4.1 Vp-p 11.28 MHz 2H IC101 wj REC/PB IC102 wj REC/PB 5 q; 340 mVp-p 3.0 Vp-pHVIC101 rh REC/PB IC102 rk REC/PB SW-368 4-54,

COVER 4-3. PRINTED WIRING BOARDS SW-368 BOARD

C002 C-2 R111 B-3 C101 B-2 R112 C-3 C102 B-3 R113 C-3 C103 B-4 R114 B-3 C104 B-4 R115 C-4 C105 B-4 R116 C-4 C106 B-3 R117 C-4 C107 B-3 R118 C-4 C108 B-4 R119 C-4 C109 B-2 R120 C-4 C110 B-2 R121 C-3 C111 C-3 R122 C-4 C112 C-3 R123 B-4 C113 C-3 R124 B-4 C114 B-3 R125 C-3 C115 B-3 R126 A-3 C116 C-4 R127 A-2 C117 C-4 R128 C-1 C118 C-4 R129 C-3 C119 C-4 R130 C-3 C120 C-3 R131 A-3 C121 C-3 R132 A-3 C122 B-2 R133 C-2 C123 A-2 R134 A-3 C124 A-3 R135 A-2 C125 A-2 R136 C-1 C126 B-3 R137 B-4 R138 C-3 CN101 C-1 R139 C-3 CN102 B-1 S001 A-3 D001 A-1 S002 A-4 D002 A-1 S003 C-2 D003 A-1 S004 B-1 D004 A-1 S005 C-1 D005 A-2 D006 A-2 D007 A-4 D101 B-3 D102 IC101 B-4 IC102 A-3 IC103 C-3 L101 B-2 L102 C-3 L103 B-3 L104 B-2 Q002 C-2 Q003 C-2 Q004 A-2 Q101 B-4 Q102 B-4 Q103 C-2 Q104 C-3 Q105 A-2 Q106 C-2 Q107 A-2 Q108 A-3 Q109 C-2 R002 C-2 R003 C-2 R005 B-2 R006 C-2 R007 A-2 R008 A-2 R009 A-2 R010 A-4 R011 C-2 R012 B-1 R013 B-1 R014 C-1 R015 C-1 R018 A-2 R104 B-4 R105 B-4 R106 B-3 R107 B-4 R108 B-3 R109 B-3 R110 B-3 44-5577E SW-368,

SECTION 5

COVER ADJUSTMENTS

Before starting adjustment EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair) PC PC (Machine after a board is replaced) Save the EVR data Download the saved to a personal computer. data to a machine. Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it. (Former board) (New board) Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or in- stalled, save the data from the same model of the same destination, and download it. (Machine to be repaired) PC (Machine to be repaired) Download the data. Save the data. (The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 5-1, 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment section Adjustment Initialization of A, B, D, Initialization of A, D page datazzE, F, 7, 9 page data Initialization of B, E, F, 7, 9, page datazzVideo Video sync level adj. zzzzzVideo burst level checkzzzCamera Flange back adj. zzzzzFNo. compensationzzzzzMechanical shutter adj. zzzzzLight value adj. zzzzzzMixed color cancel adj. zzzzzzAuto white balance standard data inputzzzzzzCCD linearity checkzzColor reproduction adj. zzzzzzCCD (white and black) defectzzzzzcompensation Strobe white balance adj. zzzzzzzzLCD LCD initial data inputzzzVCO adj. zzzzBlack limit adj. zzzzBright adj. zzzzContrast adj. zzzzVG Center adj. zzzzPSIG Gray adj. zzzzV-COM adj. zzzzzWhite balance adj. zzzzzzTable 5-1-1 Note : When replacing the lens block or the SY-77 board, refer to “Precaution on Replacing the Lens Block or the SY-77 board”. (See page 6) 5-2 Lens block assy (Note) Flash unit LCD block LCD901 (LCD panel) LCD block D901 (Back light unit) CD-397 board IC101 (CCD imager) CH-111 board (Camera Module) SY-77 board IC508 (EVR) SY-77 board IC601 (CAMERA DSP) SY-77 board IC101 (VIDEO AMP) SW-368 board IC101 (LCD drive) SW-368 board IC102 (LCD Timing generator) ST-70 board (COMPLETE) SY-77 board (COMPLETE) (Note) SW-368 board (COMPLETE) SY-77 board IC505 EEPROM Supporting RRRRRRaaaaaaddddddaaaaaarrrrrrWWWWWW, 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check J-1 Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check J-2 Pattern box PTB-450 J-6082-200-A J-3 Color bar chart for pattern box J-6020-250-A Adjusting remote commander (RM-95 upgraded). J-4 J-6082-053-B (Note 1) J-5 Siemens star chart J-6080-875-A For checking the flange back J-6 Clear chart for pattern box J-6080-621-A For connecting the adjusting remote commander J-7 CPC-9 jig (Note 2) J-6082-393-C For adjusting the LCD block J-8 Minipattern box J-6082-353-B For adjusting the flange back J-9 Back ground paper J-2501-130-A For adjusting the strobe Note 1: If the micro processor IC in the adjusting remote Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be commander is not the new micro processor (UPD7503G- used, because it cannot operate the adjusting remote com- C56-12), The pages cannot be switched. In this case, mander. replace with the new micro processor (8-759-148-35). J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 Fig. 5-1-1 5-3, 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer Pattern box to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-1- 6. 2) Connect the Adjusting remote commander to SY-77 board L CN706 via CPC-9 jig (J-6082-393-C). (See Fig. 5-1-3) Note 3: Setting the “Forced CAMERA mode power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 21, set data: 03, and press Front of the lens the PAUSE button of the adjusting remote com- mander. The above procedure will enable the camera power to be turned on. After completing adjustments, be L = About 30 cm sure to exit the “Forced CAMERA mode power ON Mode”. Fig. 5-1-2 Note 4: Exiting the “Forced CAMERA mode power ON Mode” 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 21, set data: 00, and press the PAUSE button of the adjusting remote com- mander. 3) Select page: 0, address: 01, and set data: 00. 1-1-3. Discharging of the Flashlight Power Supply The capacitor which is used as power supply of flashlight is charged CPC-9 jig (J-6082-393-C) with 200 V to 300 V voltage. Discharge this voltage before start- (Note 1, 2) ing adjustments in order to protect service engineers from electric shock during adjustment. Discharge procedure CPC cover 1. Press the FLASH button (SW-368 board S004 (CONTROL SY-77 board UP)) and set the NO FLASH mode. CN706 2. Fabricate the discharging jig as shown in Fig. 5-1-5 locally by yourself. Connect the discharging jig to the positive (+) and negative (–) terminal of the flash voltage charge capacitor. Al- low ten seconds to discharge the voltage. R:1 kΩ/1 W (Part code: 1-215-869-11) Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) Capacitor cannot be used, because it cannot operate the adjusting remote commander. Fig. 5-1-3 1 kΩ/1 W Wrap insulating tape. Fig. 5-1-4 Fig. 5-1-5 5-4, CONTROL SWITCH BLOCK Must be connected when the MIC UNIT is used. MIC AF Illumination LENS UNIT ST-70 BOARD CN351 CN704 CN705 SY-77 BOARD CN001 CN701 CN703 CN301 CN706 CN702 JK-227 BOARD SPEAKER JK-226 BOARD Must be connectedwhen the Memory Stick J002 is used. CN002 J001 MS SOCKET

USB

A/V OUT jack jack To battery terminal DC IN jack Need not connected Audio (Black) Vectorscope Color monitor Terminated CN101Video (yellow) 75 Ω CN102 AC IN SW-368 BOARD PANEL UNIT AC power adaptor Adjusting remote commander 18 1 Regulated power supply (6.0 to 7.2 Vdc) Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. CPC-9 jig (Note 1, 2) It causes damage to the unit. (J-6082-393-C) Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjusting remote commander.

Fig. 5-1-6

5-5, 1-1-4. Precautions 1. Setting the Switch Unless otherwise specified, set the switches as follows and per- form adjustments. 1. Mode Dial ... CAMERA 2. ZOOM switch (SW-368 board S001, S002) ... WIDE end 3. EV (Menu display) ... 0EV 4. DSIPLAY/LCD ON/OFF button (SW-368 board S005) ... OSD OFF 5. WB (WHITE BALANCE) (Menu display) ... AUTO 6. P.EFFECT (Menu display) ... OFF 7. VIDEO OUT (SET UP setting) ... NTSC 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame

H

C C=D D CRT picture frame

V

A B A=BBAFig. b (monitor TV picture) Enlargement Difference in level Adjust the camera zoom and direction to obtain the output waveform shown in Fig a and the monitor TV display shown in Fig. b. B A Fig. 5-1-7 3. Subjects 1) Color bar chart (Standard picture frame). When performing adjustments using the color bar chart, ad- just the picture frame as shown in Fig. 5-1-7. (Standard pic- ture frame) 2) Clear chart (Standard picture frame) Remove the color bar chart from the pattern box and insert a White clear chart in its place. (Do not perform zoom operations dur- 841 mm ing this time) Black 3) Chart for flange back adjustment Join together a piece of white A0 size paper (1189mm × 841 mm) and a piece of black paper to make the chart shown in Fig. 5-1-8. 1189 mm Note: Use a non-reflecting and non-glazing vellum paper. The Fig. 5-1-8 size must be A0 or larger and the joint between the white and black paper must not have any undulations. 5-6 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15 mm thickness. woody board A (2) woody board B (2) woody board C (1) 530 mm 500 mm 1000 mm (400 mm) (370 mm) (700 mm) 1026 mm: Depth1m1026 mm: Depth1m1000 mm (513 mm: Depth 50 cm) (513 mm: Depth 50 cm) (700 mm) 1030 mm 1000 mm (730 mm) (700 mm) Fig. 5-1-9 2) Apply black mat paint to one side of woody board A and B. 3) Attach background paper (J-2501-130-A) to woody board C. 4) Assemble so that the black sides and the background paper side of woody board A, B and C are internal. (Fig 5-1-10) woody board A woody board B woody board A woody board B woody board C Fig. 5-1-10 5-7, 1-2. INITIALIZATION OF A, B, D, E, F, 7, 9 PAGE 3. A Page table DATA Note 1: Fixed data-1: Initialized data. 1-2-1. Initialization of A, D Page Data (Refer to “1. Initializing the A Page Data”) 1. Initializing A, D Page Data Note 2: Fixed data-2: Modified data. Note: If the A, D page data has been initialized, the following (Refer to “2. Modification of A Page Data”) adjustments need to be performed again. Address Initial value Remark 1) Modification of A, D page data 00, 01 Fixed data-1 (Initialized data) 2) Video system adjustments 3) LCD system adjustments 02 00 Test mode 4) System control system adjustments 03 to 81 Fixed data-1 (Initialized data) 82 6A VCO adj. (NTSC) Adjsuting page A 83 7C VCO adj. (PAL) Adjsuting Address 00 to FF 84 20 V-COM adj. Adjusting page D 85 BC Bright adj. Adjusting Address 10 to 73 86 08 Black limit adj. Initializing Method: 87 BF Psig Gray adj. Order Page Address Data Procedure 88 94 White balance adj. 1 0 01 01 89 7A2403 0B 8A 3F Contrast adj. 3 4 00 2D 8B 3F VG Center adj. 4 4 01 2D Press PAUSE button. 8C Fixed data-1 (Initialized data) 5 4 02 Check the data changes to “01”. 8D Fixed data-2 Perform “Modification of 8F to 9F Fixed data-1 (Initialized data) 6 A, D page Data”. A0 80 Video sync level adj. A1 to A8 Fixed data-1 (Initialized data) 2. Modification of A, D Page Data A9 Fixed data-2 If the A, D page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual AA to FF Fixed data-1 (Initialized data) input. Modifying Method: 4. D Page table 1) Before changing the data, select page: 0, address: 01, and set Note 1: Fixed data-1: Initialized data. data: 01. (Refer to “1. Initializing the D Page Data”) 2) New data for changing are not shown in the tables because Note 2: Fixed data-2: Modified data. they are different in destination. When changing the data, copy (Refer to “2. Modification of D Page Data”) the data built in the same model. Address Initial value Remark Note: If copy the data built in the different model, the 10 to 20 Fixed data-1 (Initialized data) camera may not operate. 3) When changing the data, press the PAUSE button of the 21 00 Test mode adjusting remote commander each time when setting new data 22 to54 Fixed data-1 (Initialized data) to write the data in the non-volatile memory. 55 Fixed data-2 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. 56 to 73 Fixed data-1 (Initialized data) Processing after Completing Modification of A, D Page Data: Order Page Address Data Procedure1200 292201 29 Press PAUSE button. 5-8, 1-2-2. Initialization of B, E, F, 7, 9 Page Data 3. B Page Table 1. Initializing B, E, F, 7, 9 Page Data Note 1: Fixed data-1: Initialized data. Note: If the B, E, F, 7, 9 Page data has been initialized, (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) “Modification of B, E, F, 7, 9 Page Data” and following Note 2: Fixed data-2: Modified data. adjustments need to be performed again. (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) 1) Modification of B, E, F, 7, 9 page data Address Initial value Remark 2) Camera system adjustments 00 to 6D Fixed data-1 (Initialized data) Adjusting page B 6E Fixed data-2 Adjusting Address 00 to FF 6F to FF Fixed data-1 (Initialized data) Adjusting page E Adjusting Address 00 to FF 4. E Page Table Adjusting page F Note 1: Fixed data-1: Initialized data. Adjusting Address 00 to FF (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) Note 2: Fixed data-2: Modified data. Adjusting page 7 (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) Adjusting Address 00 to FF Address Initial value Remark Adjusting page 9 00 to 94 Fixed data-1 (Initialized data) Adjusting Address 00 to FF 95 Fixed data-2 96 Fixed data-2 Initializing Method: 97 to CF Fixed data-1 (Initialized data) Order Page Address Data Procedure D0 Fixed data-21001 01 D1 to FF Fixed data-1 (Initialized data) 2 6 03 0B3600 2D4601 2D Press PAUSE button. 5 6 02 Check the data changes to “01”. Perform “Modification of B, E, F, 7, 9 page Data”. 2. Modification of B, E, F, 7, 9 Page Data If the B, E, F, 7, 9 Page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camera may not operate. 3) When changing the data, press the PAUSE button of the adjusting remote commander each time when setting new data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. Processing after Completing Modification of B, E, F, 7, 9 Page data Order Page Address Data Procedure1200 292201 29 Press PAUSE button. 5-9, 5. F Page Table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7, 9 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) Address Initial value Remark Address Initial value Remark 00 to 0F Fixed data-1 (Initialized data) 3E FF Flange back adj. 10 FF 3F Fixed data-1 (Initialized data) 11 FF 40 00 12 FF 41 00 AF Ilumination check. 13 FF 42 00 14 FF 43 00 15 FF 44 00 16, 17 Fixed data-1 (Initialized data) 45 00 18 36 46 00 19 54 47 00 1A 87 48 00 1B 71 49 00 Flange back adj. 1C 10 4A 00 1D C0 4B 00 1E 00 4C 00 1F 00 4D 00 20 00 4E 00 21 00 4F 00 22 00 50 00 23 00 51 00 24 20 52 00 25 20 53 00 26 13 54 to 5D Fixed data-1 (Initialized data) 27 46 5E 00 28 0A 5F 00 29 00 60 00 2A 00 61 00 F No. compensation Flange back adj. 2B 00 62 00 2C 00 63 00 2D 00 64 00 2E 00 65 30 2F 00 66 FE Light value adj. 30 00 67 6D 31 00 68 to 6D Fixed data-1 (Initialized data) 32 00 6E 00 Mixed color cancel adj. 33 00 6F 00 34 00 70 32 35 00 71 B2 36 00 72 23 37 00 73 64 AWB 3200K standard data input 1 38 00 74 32 39 00 75 6C 3A 00 76 23 3B 00 77 88 3C 00 78 33 AWB 3200K standard data input 2 3D 00 79 36 5-10, Address Initial value Remark Address Initial value Remark 7A 22 AB 45 7B 2C AC 63 7C 32 AD 83 Color reproduction adj. AWB 3200K standard data input 2 7D 68 AE 03 7E 23 AF E9 7F DF B0 00 AWB 3200K standard data input 1 80 33 B1 00 AWB 5800K standard data input 1 81 93 B2 00 AWB 3200K standard data input 1 82 22 B3 00 AWB 5800K standard data input 1 83 7F B4 00 AWB 3200K standard data input 1 AWB 3200K standard data input 3 84 32 B5 Fixed data-1 (Initialized data) 85 E2 B6 28 Strobe white balance adj. 86 25 B7 6E 87 12 B8 10 88 20 B9 6B 89 F5 BA 0F 8A 33 BB F6 8B 14 BC 0F AWB 5800K standard data input 1 8C 20 BD F7 8D E2 BE 00 8E 33 BF 00 8F 89 C0 00 90 21 C1 00 91 69 C2 00 92 32 C3 00 93 62 C4 00 AWB 5800K standard data input 2 94 21 C5 00 95 52 C6 00 96 33 C7 30 Mechanical shutter adj. 97 94 C8 1B 98 21 C9 12 99 52 CA 00 9A 30 CB 00 9B 80 CC 80 AWB 5800K standard data input 3 9C 23 CD 90 9D A8 CE 98 9E 33 CF 90 9F C3 D0 88 A0 2A D1 00 A1 48 D2 00 AWB 5800K standard data input 1, 2, 3 A2 61 D3 00 A3 B0 D4 00 A4 03 D5 00 A5 E9 D6 00 A6 63 D7 14 A7 83 Color reproduction adj. D8 to DA Fixed data-1 (Initialized data) A8 D5 DB 00 A9 FE DC 00 Strobe white balance adj. AA 73 DD 00 5-11, Address Initial value Remark 6. 7 Page Table Note 1: Fixed data-1: Initialized data. DE 00 (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) DF 00 Note 2: Fixed data-2: Modified data. E0 00 (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) E1 00 Address Initial value Remark E2 00 00 to FF Fixed data-1 (Initialized data) E3 00 E4 00 7. 9 Page Table E5 00 Note 1: Fixed data-1: Initialized data. E6 00 (Refer to “1. Initializing B, E, F, 7, 9 Page Data”) Strobe white balance adj. E7 00 Note 2: Fixed data-2: Modified data. (Refer to “2. Modification of B, E, F, 7, 9 Page Data”) E8 00 Address Initial value Remark E9 00 00 to FF Fixed data-1 (Initialized data) EA 00 EB 00 EC 00 ED 00 EE 00 EF 00 F0 to FF Fixed data-1 (Initialized data) 5-12, 1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Check 1. Video Sync Level Adjustment Adjust the burst level of the composite video signal output. Adjust the sync level of the composite video signal output. Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Video terminal of A/V OUT jack Measurement Point Video terminal of A/V OUT jack (75 Ω terminated) (75 Ω terminated) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Specified Value A = 286 ± 30 mVp-p (NTSC) Adjustment PageAA= 300 ± 30 mVp-p (PAL) Adjustment Address A0 Specified Value A = 286 ± 5 mVp-p (NTSC) Adjusting method: A = 300 ± 5 mVp-p (PAL) Order Page Address Data Procedure1001 01 Adjusting method: 2 A 02 03 Press PAUSE button Order Page Address Data Procedure34F1 041001 01 Check that the burst level (A) 4 A A02A02 03 Press PAUSE button is satisfied the specified value. 3 4 F1 045AA0 Press PAUSE button Change the data and set the4AA0 sync level (A) to the specified Processing after Completing Adjustments: value. Order Page Address Data Procedure5AA0 Press PAUSE button1A02 00 Press PAUSE button Processing after Completing Adjustments: 2 4 F1 003001 00 Order Page Address Data Procedure1A02 00 Press PAUSE button24F1 003001 00

A A

H H Fig. 5-1-11 Fig. 5-1-12 5-13, 1-4. CAMERA SYSTEM ADJUSTMENTS After completing the camera system adjustments, Before perform the camera system adjustments, check that the release the data setting: specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Order Page Address Data Procedure isfied. Note: For “CAMERA SYSTEM ADJUSTMENTS”, perform in1E96 40 Press PAUSE button. order of item numbers. 2 B 6E B0 Press PAUSE button. 3 6 6C 00 Data setting during camera system adjustments Perform the following data setting before the camera system ad- 4 D 21 00 Press PAUSE button. justments. Set the bit value of bit 1 is It is not necessary to perform the following data setting everytime5A02 “0”, and press PAUSE when you perform some items of camera system adjustments con- button. (Note 1) tinuously unless the power is turned off. Only when the power is Set the bit value of bit 1 is turned off during this adjustments, perform the data setting again, 6 A 00 “0”, and press PAUSE then continue the adjustments. button. (Note 1) Set up setting: Set the bit value of bit 5 is 1) VIDEO OUT of SET UP setting... NTSC (NTSC mode) 7 A 01 “0”, and press PAUSE (This adjustment must be performed in NTSC mode, so don't button. (Note 1) set the SET UP setting to “PAL”) 8 0 01 00 Data setting method: Order Page Address Data Procedure1001 01 Set the bit value of bit 5 is2A01 “1”, and press PAUSE button. (Note 1) Check the bit values of bit3, 3 2 10 bit4 and bit5 are “1”. (Note 1, 2) Set the bit value of bit 1 is4A00 “1”, and press PAUSE button. (Note 1) Set the bit value of bit 1 is5A02 “1”, and press PAUSE button. (Note 1) 6 D 21 03 Press PAUSE button. Check the data changes to76C1 “02”. 8 6 6C 01 9 Wait for 1 second. 10 B 6E 80 Press PAUSE button. 11 E 95 E0 Press PAUSE button. 12 E 96 00 Press PAUSE button. 13 E D0 10 Press PAUSE button. Note 1: For the bit values, refer to “5-2. SERVICE MODE”, “2-3. 2. Bit value discrimination”. Note 2: In case of wrong data. • Select page: 2, address: 00 and set data: 29. • Select page: 2, address: 01 and set data: 29. • Select page: 2, address: 0C, set the bit value of bit 1 is 1. • Select page: 2, address: 04 and set data: 04. Set the adjusting remote commander to normal LANC, and the power will be turned, off and on automatically. Note 3: Repeat the “Data setting method”, if the power was turned off and on during the “CAMERA SYSTEM ADJUST- MENTS”. 5-14, Picture Frame Setting How to reset the zoom and focus when they deviated: Mode CAMERA Order Page Address Data Procedure Subject Color bar chart162C 01 (Standard picture frame with the2690 00 zoom lens at WIDE end) Set the following data. Measurement Point Video terminal of A/V OUT jack3691 00: WIDE end (75 Ω terminated) 04: TELE end Measuring Instrument Oscilloscope and monitor TV4692 YL (Note 2) Specified Value A=B, C=D, E=F5693 YH (Note 2) Note 1: Displayed data of the page 1 of adjusting remote com- 6 6 01 79 Press PAUSE button. mander. 1:XX:XX Check the data changes to7 6 07 YL data “01”. YH data8601 00 Press PAUSE button. Note 2: The data noted down at step 7 of “Setting method”. Switch setting 1) FOCUS (Menu setting) ... MULTI AF Check on the oscilloscope 2) MACRO (Control button) ... ON 1. Horizontal period Setting method: Order Page Address Data Procedure A=B C=D Shoot the color bar chart1BCwith the zoom WIDE end. A D Enter the output of VIDEO OUT to the monitor TV, and move the position as shown in Fig. 5-1-15. Horizontal width of one color (B, C) and that of black (A, 3 D) on the color bar chart should be same. (See Fig. 5- 1-13) With vertical width of black (E, F) set in same, the color 4 bar chart should come to the center of monitor TV. (See Fig. 5-1-14) Check that the color bar on the monitor TV is focused. Fig. 5-1-136003 22 2. Vertical period Note down the YH and YL71data. (Note 1) E E=F F Processing after Completing Adjustment: Order Page Address Data Procedure1003 00

V

Fig. 5-1-14 Check on the monitor TV Color bar chart picture frame Monitor TV picture frame Fig. 5-1-15 5-15, 1. Flange Back Adjustment Adjusting method: (Using the minipattern box) RadarW Order Page Address Data Procedure The flange back of inner focus lens is adjusted automatically. If shifted, the auto focus is disordered. Perform “Data setting during 1 camera system adjustment”. Mode CAMERA (Refer to page 5-14) Subject Siemens star chart with ND filter2601 13 Press PAUSE button. for minipattern box (Note 1) Press PAUSE button. Measurement Point Check operation on monitor TV3601 27 (Note 5) Measuring Instrument Check the data changes to Adjustment PageF4602 “01”. Adjustment Address 18 to 3E, 40 to 53 Check the data. Note 1: Dark Siemens star chart. 5 F 3E 00: Normal Note 2: Check that the data of page: 6, address: 02 is “00”. 01 to FF: Defective If not, turn the power of unit OFF/ON. Note 5: The adjustment data will be automatically input to page: F, address: 18 to 3E and 40 to 53. Preparations before adjustments: 1) The minipattern box is installed as shown in the following fig- Processing after Completing Adjustment: ure. Note 3: The attachment lenses are not used. Order Page Address Data Procedure Note 4: Take care not to hit the mini-pattern box when ex- 1 6 01 00 Press PAUSE button. tending the lens. Release the data setting 2) Install the minipattern box so that the distance between it and 2 performed at step 1. the front of lens of camera is less than 3 cm. (Refer to page 5-14) 3) Make the height of minipattern box and the camera equal. 4) Check the output voltage of the regulated power supply is the Perform “Flange Back3 specified voltage ± 0.01 Vdc. Check”. 5) Check that the center of Siemens star chart meets the center of shot image screen with the zoom lens at TELE end and WIDE end respectively. Specified voltage: The specified voltage varies according to the minipattern box, so adjustment the power sup- ply output voltage to the specified voltage writ- ten on the sheet which is supplied with the mini- pattern box. Below 3 cm Minipattern box Camera Camera table Regulated power supply Output voltage : Specified voltage ± 0.01 Vdc Output current : more than 3.5 A Red (+) Black (–) Yellow (SENS +) White (SENS –) Need not connected Black (GND) Fig. 5-1-16 5-16, 2. Flange Back Adjustment RadarW 3. Flange Back Check RadarW (Using the flange back adjustment chart) Mode CAMERA The flange back of inner focus lens is adjusted automatically. If shifted, the auto focus is disordered. Subject Siemens star (1.0 m from the front of the lens) Mode CAMERA (Luminance: 200 to 400 lux) Subject Flange back adjustment chart Measurement Point Check operation on monitor TV (2.0 m from the front of lens) (Luminance: 300 to 400 lux) Measuring Instrument Measurement Point Check operation on monitor TV Specified value Focused at the TELE end and WIDE end Measuring Instrument Adjustment Page F Checking method: Adjustment Address 18 to 3E, 40 to 53 Order Page Address Data Procedure Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Place the Siemens star 1.0 m1 from the front of the lens. Preparations before adjustments: To open the IRIS , decrease 1) Place the Flange back adjustment chart 2.0 m from the front the luminous intensity to the of the lens. 2 Siemens star up to a point 2) Check that the center of Flange back adjustment chart meets before noise appear on the the center of shot image screen with the zoom lens at TELE image. end and WIDE end respectively. Perform “Data setting during 3 camera system adjustment”. Adjusting method: (Refer to page 5-14) Order Page Address Data Procedure4B3D Note down the data. Perform “Data setting during5B3D 50 Press PAUSE button. 1 camera system adjustment”. Shoot the Siemens star with (Refer to page 5-14) 6 the zoom TELE end. 2 6 01 13 Press PAUSE button. 7 Turn on the auto focus. Press PAUSE button. 3 6 01 15 Check that the lens is (Note 2) 8 focused. Check the data changes to4602962C 01 “01”. While observe the TV Check the data. monitor, change the zoom to5F3E 00: Normal 10 the WIDE end and check that 01 to FF: Defective the lens is focused. Note 2: The adjustment data will be automatically input to page: F, address: 18 to 3E and 40 to 53. Processing after Completing Adjustment: Processing after Completing Adjustment: Order Page Address Data Procedure Order Page Address Data Procedure162C 001601 00 Press PAUSE button. Set data noted down at step2 B 3D 4, and press PAUSE button. Release the data setting 2 performed at step 1. Release the data setting (Refer to page 5-14) 3 performed at step 3. (Refer to page 5-14) Perform “Flange Back Adjustment (2)”. 5-17, 4. F No. Compensation RadarW 5. Mechanical Shutter Adjustment RadarW Compensate the unevenness of the iris meter sensitivity. Adjust the period which the mechanical shutter is closed, and com- pensate the exposure. Mode CAMERA Subject Clear chart Mode CAMERA (Standard picture frame with the Subject Clear chart zoom lens at WIDE end) (Standard picture frame with the Adjustment Page F zoom lens at WIDE end) Adjustment Address 5E to 64 Adjustment Page F Note 1: Check that the data of page: 6, address: 02 is “00”. Adjustment Address B8 to D7 If not, turn the power of unit OFF/ON. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Adjusting method: Adjusting method: Order Page Address Data Procedure Perform “Data setting during Order Page Address Data Procedure 1 camera system adjustment”. Perform “Data setting during (Refer to page 5-14) 1 camera system adjustment”. Perform “Picture Frame (Refer to page 5-14) 2 setting”. Perform “Picture Frame (Refer to page 5-15) 2 setting”. Press PAUSE button. (Refer to page 5-15) 3 6 01 BB (Note 2) Press PAUSE button. 3 6 01 AD Check the data changes to (Note 2) 4 6 02 “01”. Check the data changes to4602 Note 2: The adjustment data will be automatically input to page: “01”. F, address: 5E to 64. 5 6 AB Check the data is “00”. Note 2: The adjustment data will be automatically input to page: Processing after Completing Adjustment: F, address: B8 to D7. Order Page Address Data Procedure Processing after Completing Adjustment: 1 6 01 00 Press PAUSE button. Release the data setting Order Page Address Data Procedure 2 performed at step 1. 1 6 01 00 Press PAUSE button. (Refer to page 5-14) Release the data setting 2 performed at step 1. (Refer to page 5-14) 5-18, 6. Light Value Adjustment RadarW 7. Mixed Color Cancel Adjustment RadarW Adjust the standard LV value. To perform mixed color cancel adjustment based on data of each color in color bar. Mode CAMERA Subject Clear chart Mode CAMERA (Standard picture frame with the Subject Color bar chart zoom lens at WIDE end) (Standard picture frame with the Measurement Point Displayed data of page: 1 (Note zoom lens at WIDE end) 2) and page: F, address: 65 Adjustment Page F Measuring Instrument Adjusting remote commander Adjustment Address 6E and 6F Adjustment Page F Note 1: Check that the data of page: 6, address: 02 is “00”. Adjustment Address 65 to 67 If not, turn the power of unit OFF/ON. Specified Value AE level 1: 0FE0 to 1020 Adjusting method: AE level 2: 2F to 50 Note 1: Check that the data of page: 6, address: 02 is “00”. Order Page Address Data Procedure If not, turn the power of unit OFF/ON. Perform “Data setting during Note 2: The right four digits of the page: 1 displayed data of the 1 camera system adjustment”. adjusting remote commander. (Refer to page 5-14) 1:XX:XX Perform “Picture Frame Displayed data 2 setting”. (Refer to page 5-15) Adjusting method: 3 7 22 Note down the data. Order Page Address Data Procedure4722 00 Press PAUSE button. Perform “Data setting during5601 D7 Press PAUSE button. 1 camera system adjustment”. (Refer to page 5-14) Press PAUSE button.6 6 01 D5 (Note 2) Perform “Picture Frame 2 setting”. Check the data changes to7 6 02 (Refer to page 5-15) “01”. Press PAUSE button. Note 2: The adjustment data will be automatically input to page: 3 6 01 0D (Note 4) F, address: 6E and 6F. Check the data changes to4602 Processing after Completing Adjustment: “01”. Order Page Address Data Procedure5003 061601 00 Press PAUSE button. Check that the displayed data61(Note 2) satisfies the AE Set the data noted down at level 1 specified value. 2 7 22 step 3, and press PAUSE button. Check that the displayed data7F65 satisfies the AE level 2 Release the data setting specified value. 3 performed at step 1. Note 3: (Refer to page 5-14)The adjustment data will be automatically input to page: F, address: 65 to 67. Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. 2 0 03 00 Release the data setting 3 performed at step 1. (Refer to page 5-14) 5-19, 8. Auto White Balance 3200K Standard Data Input 1 Processing after Completing Adjustment: RadarW Order Page Address Data Procedure Adjust the white balance standard data at 3200K. 1 6 01 00 Press PAUSE button. Mode CAMERA2637 00 Subject Clear chart Set data noted down at step 3, 3 6 B6 (Standard picture frame with the and press PAUSE button. zoom lens at WIDE end and Release the data setting TELE end) 4 performed at step 1. Adjustment Page F (Refer to page 5-14) Adjustment Address 70 to 77, B0, B2, B4 Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Note 2: “Auto White Balance 3200K Standard Data Input 1” is available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame 2 setting”. (WIDE end) (Refer to page 5-15) 3 6 B6 Note down the data. 4 6 B6 03575D Note down the data. 6 7 5D 00 Press PAUSE button. 7 7 9D Note down the data. 8 7 9D 80 Press PAUSE button. 9 6 37 01 10 6 01 11 Press PAUSE button. Check the data changes to 11 6 38 “01”. 12 6 01 C1 Press PAUSE button. (Note 3) Check the data changes to 13 6 02 “01”. Set data noted down at step 5, 14 7 5D and press PAUSE button. Set data noted down at step 7, 15 7 9D and press PAUSE button. 16 6 01 00 Press PAUSE button. Perform “Picture Frame 17 setting”. (TELE end) (Refer to page 5-15) 18 6 37 02 19 6 01 0B Press PAUSE button. (Note 3) Check the data changes to 20 6 02 “01”. Note 3: The adjustment data will be automatically input to page: F, address: 70 to 77, B0, B2 and B4. 5-20, 9. Auto White Balance 3200K Standard Data Input 2 10. Auto White Balance 3200K Standard Data Input 3 RRaaddaarrW RRaaddaarrW Adjust the white balance standard data at 3200K. Adjust the white balance standard data at 3200K. Mode CAMERA Mode CAMERA Subject Clear chart Subject Clear chart (Standard picture frame with the (Standard picture frame with the zoom lens at WIDE end) zoom lens at WIDE end) Adjustment Page F Adjustment Page F Adjustment Address 78 to 7F Adjustment Address 80 to 87 Note 1: Check that the data of page: 6, address: 02 is “00”. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON. Note 2: “Auto White Balance 3200K Standard Data Input 2” is Note 2: “Auto White Balance 3200K Standard Data Input 3” is available only once after the power is turned on. Turn the available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. power off, then on again if the adjustment is retried. Adjusting method: Adjusting method: Order Page Address Data Procedure Order Page Address Data Procedure Perform “Data setting during Perform “Data setting during 1 camera system adjustment”. 1 camera system adjustment”. (Refer to page 5-14) (Refer to page 5-14) Perform “Picture Frame Perform “Picture Frame22setting”. (Refer to page 5-15) setting”. (Refer to page 5-15) 3 6 B6 Note down the data. 3 6 B6 Note down the data. 4 6 B6 0346B6 035637 045637 066601 0B Press PAUSE button. (Note 3) 6 6 01 0B Press PAUSE button. (Note 3) Check the data changes to Check the data changes to76027602 “01”. “01”. Note 3: The adjustment data will be automatically input to page: Note 3: The adjustment data will be automatically input to page: F, address: 78 to 7F. F, address: 80 to 87. Processing after Completing Adjustment: Processing after Completing Adjustment: Order Page Address Data Procedure Order Page Address Data Procedure1601 00 Press PAUSE button. 1 6 01 00 Press PAUSE button. 2 6 37 002637 00 Set data noted down at step 3, Set data noted down at step 3, 3 6 B636B6 and press PAUSE button. and press PAUSE button. Release the data setting Release the data setting 4 performed at step 1. 4 performed at step 1. (Refer to page 5-14) (Refer to page 5-14) 5-21, 11. Auto White Balance 3200K Check RadarW Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Clear chart1601 00 Press PAUSE button. (Standard picture frame with the Set data noted down at step zoom lens at WIDE end) 2 7 5D 5, and press PAUSE button. Measurement Point Displayed data Video terminal of Set data noted down at step of Page: 1 A/V OUT jack379D 7, and press PAUSE button. (Note 2) (75 Ω terminated) 4 0 03 00 Specified Value R ratio: 3FA0 to 40605637 00 B ratio: 3FA0 to 4060 R-Y level data: 7E to 82 Set data noted down at step6 6 B6 B-Y level data: 7E to 82 3, and press PAUSE button. Y level data: 10 to 40 74 Note 1: Check that the data of page: 6, address: 02 is “00”. 76 If not, turn the power of unit OFF/ON. 7C Check that the displayed data7 F Note 2: The right four digits of the page: 1 displayed data of the 7E the Y level specified value. adjusting remote commander. 84 1:XX:XX 86 Displayed data Release the data setting 8 performed at step 1. Checking method: (Refer to page 5-14) Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame 2 setting”. (WIDE end) (Refer to page 5-15) 3 6 B6 Note down the data. 4 6 B6 03575D Note down the data. 6 7 5D 00 Press PAUSE button. 7 7 9D Note down the data. 8 7 9D 80 Press PAUSE button. 9 6 37 0D 10 6 01 11 Press PAUSE button. Check the data changes to 11 6 38 “01”. 12 6 01 C1 Press PAUSE button. Check the data changes to 13 6 02 “01”. 14 0 03 04 Check that the displayed data 15 1 (Note 2) satisfied the R ratio specified value. 16 0 03 05 Check that the displayed data 17 1 (Note 2) satisfied the B ratio specified value. 18 0 03 2C Check that the R-Y level data 19 1 (Note 2) satisfied the specified value. 20 0 03 2D Check that the B-Y level data 21 1 (Note 2) satisfied the specified value. 5-22, 12. Auto White Balance 5800K Standard Data Input 1 Order Page Address Data Procedure RadarW 26 6 01 A5 Press PAUSE button. (Note 3) Adjust the white balance standard data at 5800K. Check the data changes to 27 6 02 Mode CAMERA “01”. Subject Clear chart Note 3: The adjustment data will be automatically input to page: (Standard picture frame with the F, address: 88 to 8F, A0 to A3, B1 and B3. zoom lens at WIDE end and TELE end) Processing after Completing Adjustment: Filter Filter C14 for color temperature Order Page Address Data Procedure correction1637 00 Adjustment PageF2601 00 Press PAUSE button. Adjustment Address 88 to 8F, A0 to A3, B1, B3 Set data noted down at step3B70 Note 1: Check that the data of page: 6, address: 02 is “00”. 23, and press PAUSE button. If not, turn the power of unit OFF/ON. Set data noted down at step Note 2: “Auto White Balance 5800K Standard Data Input 1” is46B6 8, and press PAUSE button. available only once after the power is turned on. Turn the Release the data setting power off, then on again if the adjustment is retried. 5 performed at step 2. (Refer to page 5-14) Adjusting method: Remove the C14 filter on the Order Page Address Data Procedure 6 lens. Place the C14 filter on the lens. Perform “Data setting during 2 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame 3 setting”. (WIDE end) (Refer to page 5-15) 4 F A0 2A Press PAUSE button. 5 F A1 48 Press PAUSE button. 6 F A2 61 Press PAUSE button. 7 F A3 B0 Press PAUSE button. 8 6 B6 Note down the data. 9 6 B6 03 10 7 5D Note down the data. 11 7 5D 00 Press PAUSE button. 12 7 9D Note down the data. 13 7 9D 80 Press PAUSE button. 14 6 37 07 15 6 01 11 Press PAUSE button. Check the data changes to 16 6 38 “01”. 17 6 01 C3 Press PAUSE button. (Note 3) Check the data changes to 18 6 02 “01”. Set data noted down at step 19 7 5D 10, and press PAUSE button. Set data noted down at step 20 7 9D 12, and press PAUSE button. 21 6 01 00 Press PAUSE button. Perform “Picture Frame 22 setting”. (TELE end) (Refer to page 5-15) 23 B 70 Note down the data. 24 B 70 10 Press PAUSE button. 25 6 37 08 5-23, 13. Auto White Balance 5800K Standard Data Input 2 14. Auto White Balance 5800K Standard Data Input 3 RadarW RadarW Adjust the white balance standard data at 5800K. Adjust the white balance standard data at 5800K. Mode CAMERA Mode CAMERA Subject Clear chart Subject Clear chart (Standard picture frame with the (Standard picture frame with the zoom lens at WIDE end) zoom lens at WIDE end) Filter Filter C14 for color temperature Filter Filter C14 for color temperature correction correction Adjustment Page F Adjustment Page F Adjustment Address 90 to 97, A0 to A3 Adjustment Address 98 to 9F, A0 to A3 Note 1: Check that the data of page: 6, address: 02 is “00”. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON. Note 2: “Auto White Balance 5800K Standard Data Input 2” is Note 2: “Auto White Balance 5800K Standard Data Input 3” is available only once after the power is turned on. Turn the available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. power off, then on again if the adjustment is retried. Adjusting method: Adjusting method: Order Page Address Data Procedure Order Page Address Data Procedure Place the C14 filter on the Place the C14 filter on the11lens. lens. Perform “Data setting during Perform “Data setting during 2 camera system adjustment”. 2 camera system adjustment”. (Refer to page 5-14) (Refer to page 5-14) Perform “Picture Frame Perform “Picture Frame33setting”. (Refer to page 5-15) setting”. (Refer to page 5-15) 4 F A0 2A Press PAUSE button. 4 F A0 2A Press PAUSE button. 5 F A1 48 Press PAUSE button. 5 F A1 48 Press PAUSE button. 6 F A2 61 Press PAUSE button. 6 F A2 61 Press PAUSE button. 7 F A3 B0 Press PAUSE button. 7 F A3 B0 Press PAUSE button. 8 6 B6 Note down the data. 8 6 B6 Note down the data. 9 6 B6 0396B6 03 10 B 70 Note down the data. 10 B 70 Note down the data. 11 B 70 10 11 B 70 10 12 6 37 0A 12 6 37 0C 13 6 01 A5 Press PAUSE button. (Note 3) 13 6 01 A5 Press PAUSE button. (Note 3) Check the data changes to Check the data changes to 14 6 02 14 6 02 “01”. “01”. Note 3: The adjustment data will be automatically input to page: Note 3: The adjustment data will be automatically input to page: F, address: 90 to 97and A0 to A3. F, address: 98 to 9F and A0 to A3. Processing after Completing Adjustment: Processing after Completing Adjustment: Order Page Address Data Procedure Order Page Address Data Procedure1637 001637 002601 00 Press PAUSE button. 2 6 01 00 Press PAUSE button. Set data noted down at step Set data noted down at step3B703B70 10, and press PAUSE button. 10, and press PAUSE button. Set data noted down at step Set data noted down at step 8, 4 6 B646B6 8, and press PAUSE button. and press PAUSE button. Release the data setting Release the data setting 5 performed at step 2. 5 performed at step 2. (Refer to page 5-14) (Refer to page 5-14) Remove the C14 filter on the Remove the C14 filter on the66lens. lens. 5-24, 15. Auto White Balance 5800K Check RadarW Order Page Address Data Procedure Mode CAMERA Check that the displayed data Subject Clear chart 22 1 (Note 2) satisfied the B ratio (Standard picture frame with the 2 specified value. zoom lens at WIDE end) Filter Filter C14 for color temperature Processing after Completing Adjustment: correction Order Page Address Data Procedure Measurement Point Displayed data of Video terminal of Set data noted down at step175D Page: 1 A/V OUT jack 6, and press PAUSE button. (Note 2) (75 Ω terminated) Set data noted down at step279D Specified Value R ratio 1: 29E8 to 2AA8 8, and press PAUSE button. B ratio 1: 6150 to 62103601 00 Press PAUSE button. R ratio 2: 29A8 to 2AE8 B ratio 2: 6110 to 62504003 00 Y level 1 data: 0E to 405637 00 Y level 2 data: 10 to 40 Set data noted down at step66B6 Note 1: Check that the data of page: 6, address: 02 is “00”. 4, and press PAUSE button. If not, turn the power of unit OFF/ON. Release the data setting Note 2: The right four digits of the page: 1 displayed data of the 7 performed at step 2. adjusting remote commander. (Refer to page 5-14) 1:XX:XX Displayed data Remove the C14 filter on the8 lens. Checking method: 8C Check that the displayed data Order Page Address Data Procedure9F94 the Y level 1 specified value. 9C Place the C14 filter on the lens. 8E Check that the displayed data 10 F 96 Perform “Data setting during the Y level 2 specified value.9E 2 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame setting”. (Refer to page 5-15) 4 6 B6 Note down the data. 5 6 B6 03675D Note down the data. 7 7 5D 00 Press PAUSE button. 8 7 9D Note down the data. 9 7 9D 80 Press PAUSE button. 10 B 37 13 11 6 01 11 Press PAUSE button. Check the data changes to 12 6 38 “01”. 13 6 01 C3 Press PAUSE button. 14 6 02 01 15 0 03 04 Check that the displayed data 16 1 (Note 2) satisfied the R ratio 1 specified value. 17 0 03 05 Check that the displayed data 18 1 (Note 2) satisfied the B ratio 1 specified value. 19 0 03 2C Check that the displayed data 20 1 (Note 2) satisfied the R ratio 2 specified value. 21 0 03 2D 5-25, 16. CCD Linearity Check RadarW Processing after Completing Adjustment: Check that CCD output keeps being straight even ISO sensitivity Order Page Address Data Procedure is changed. 1 0 03 00 Mode CAMERA Set data noted down at step Subject Clear chart2710 11, and press PAUSE button. (Standard picture frame with the Set data noted down at step zoom lens at WIDE end) 3 B 70 13, and press PAUSE button. Measurement Point Displayed data of Page: 1 (Note 1) 4 6 37 00 Measuring Instrument Adjusting remote commander5601 00 Press PAUSE button. Specified Value R ratio: 3D00 to 4300 Release the data setting B ratio: 3D00 to 4300 6 performed at step 1. Note 1: The right four digits of the page: 1 displayed data of the (Refer to page 5-14) adjusting remote commander. 1:XX:XX Displayed data Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame setting”. (Refer to page 5-15) 3 6 37 234601 0F Press PAUSE button. Check the data changes to5602 “01”. 6 0 03 04 Check that the displayed data71(Note 1) satisfied the R ratio specified value. 8 0 03 05 Check that the displayed data91(Note 1) satisfied the B ratio specified value. 10 6 01 00 Press PAUSE button. 11 7 10 Note down the data. 12 7 10 FF 13 B 70 Note down the data. 14 B 70 50 15 6 37 24 16 6 01 0F Press PAUSE button. Check the data changes to 17 6 02 “01”. 18 0 03 04 Check that the displayed data 19 1 (Note 1) satisfied the R ratio specified value. 20 0 03 05 Check that the displayed data 21 1 (Note 1) satisfied the B ratio specified value. 5-26, 17. Color Reproduction Adjustment RadarW Adjust the color separation matrix coefficient so that proper color R-Y reproduction is produced. Mode CAMERA

MG

Subject Color bar chart R (Standard picture frame with the zoom lens at WIDE end) Measurement Point Video terminal of A/V OUT jack (75 Ω terminated)

YE

Measuring Instrument Vectorscope B-Y Adjustment PageFBAdjustment Address A4 to AF Specified Value All color luminance points should settle within each color reproduction frame. Menu setting: G 1) VIDEO OUT of SET UP menu CY ... NTSC (NTSC mode) Burst position Note 1: Check that the data of page: 6, address: 02 is “00”. Fig. 5-1-17 If not, turn the power of unit OFF/ON. Note 2: “Color Reproduction Adjustment” is available only once after the power is turned on. Turn the power off, then on again if the adjustment is retried. Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) Perform “Picture Frame setting”. (Refer to page 5-15) 3 6 01 AB Press PAUSE button. 4 6 37 1F5601 A9 Press PAUSE button. (Note 3) Check the data changes to6602 “01”. 7 6 37 20 Check the each color lumi- 8 nance point is in each color reproduction frame. Note 3: The adjustment data will be automatically input to page: F, address: A4 to AF. Processing after Completing Adjustment: Order Page Address Data Procedure1637 002601 00 Press PAUSE button. Release the data setting 3 performed at step 1. (Refer to page 5-14) 5-27, 18. CCD White Defect Compensation RRaaddaarrW Mode CAMERA Subject Not required Measurement Point Displayed data of page: 6, address: 55 Measuring Instrument Adjusting remote commander Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Note 2: The“CCD White Defect Compensation” should be made when the set warms up at certain duration after the power was turned on, as it is affected with the temperature. Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) 2 E 64 Note down the data. 3 E 64 1E Press PAUSE button. 4 E 69 Note down the data. 5 E 69 09 Press PAUSE button. 6 6 01 8B Press PAUSE button. Check the data changes to7602 “01”. Check the data. 8 6 55 00 to 7F: Normal 80 to FF: Defective9601 00 Press PAUSE button. 10 E 64 0F Press PAUSE button. 11 E 69 60 Press PAUSE button. 12 6 01 87 Press PAUSE button. Check the data changes to 13 6 02 “01”. Check the data. 14 6 55 00: Normal 01 to FF: Defective Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. Set data noted down at step2E64 2, and press PAUSE button. Set data noted down at step3E69 4, and press PAUSE button. Release the data setting 4 performed at step 1. (Refer to page 5-14) 5-28, 19. CCD Black Defect Compensation RadarW Processing after Completing Adjustment: Mode CAMERA Order Page Address Data Procedure Subject Clear chart1601 00 Press PAUSE button. (Standard picture frame with the262C 00 zoom lens at WIDE end) 3 6 30 00 Measurement Point Displayed data of page: 6, address: 554691 00 Measuring Instrument Adjusting remote commander Set data noted down at step5 E 65 2, and press PAUSE button. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Release the data setting Note 2: Check that there are no dust, no dirt and reflection of the 6 performed at step 1. clear chart. (Refer to page 5-14) Note 3: Any subject other than the clear chart should be in the screen. Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) 2 E 65 Note down the data. 3 E 65 4C Press PAUSE button. 4 6 2C 015690 006691 037692 008693 009601 79 Press PAUSE button. 10 6 30 08 Check the data changes to 11 6 07 “01”. 12 Wait for 4 seconds. 13 6 01 8D Press PAUSE button. Check the data changes to 14 6 02 “01”. Check the data. 00 to 14 : Normal 15 6 55 15 to FF : Defective (Note 4) 16 6 01 00 Press PAUSE button. 17 E 65 5A Press PAUSE button. 18 6 01 89 Press PAUSE button. Check the data changes to 19 6 02 “01”. Check the data. 20 6 55 00: Normal 01 to FF: Defective Note 4: If the data is “00” at the check in this adjustment method order #15, skip the orders from #16 to #20 , and go for- ward to “Processing after Completing Adjustment. 5-29, 20. Strobe White Balance Adjustment RadarW Order Page Address Data Procedure Adjust the white balance when the strobe light flashed. Check that the displayed data Mode CAMERA 16 F E8 satisfies the Y level specified Subject Flash adjustment box (Note 3) value. Paper which reflection rate is 17 6 01 00 Press PAUSE button. 18% (Note 6) 18 6 90 E0 (50 cm from the front of lens) 19 6 91 01 Measurement Point Displayed data of page: 1 (Note 4) and page: F, address: E8, EA, 20 6 01 79 Press PAUSE button. EC, EE Check the data changes to21 6 07 Measuring Instrument Adjusting remote commander “01”. Adjustment Page F 22 6 01 67 Press PAUSE button. Adjustment Address B6, B7, DB to EF 23 Check the flashing. Specified Value Y level data: 07 to 10 Check the data changes to24 6 02 R-Y level data: “01”. 007A to 0086 (Note 4) 25 6 01 00 Press PAUSE button. B-Y level data: 26 6 90 00 007A to 0086 (Note 4) 27 6 91 00 Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. 28 6 01 79 Press PAUSE button. Note 2: Perform this adjustment in the Flash adjustment box. Check the data changes to29 6 07 Note 3: Refer to “4. Preparing the Flash adjustment box”. “01”. (See page 5-7) 30 6 01 67 Press PAUSE button. Note 4: The right four digits of the page: 1 displayed data of the 31 Check the flashing. adjusting remote commander. 1:XX:XX Check the data changes to32 6 02 Displayed data “01”. Note 5: “Strobe White Balance Adjustment” is available only 33 6 01 00 Press PAUSE button. once after the power is turned on. Turn the power off, 34 6 01 67 Press PAUSE button. then on again if the adjustment is retried. Note 6: Background paper (J-2501-130-A). 35 Check the flashing. Check the data changes to Switch setting: 36 6 02 “01”. 1) FLASH (Control button) ... ON 37 6 01 00 Press PAUSE button. Adjusting method: 38 6 01 B9 Press PAUSE button. (Note 7) Order Page Address Data Procedure 39 Check the flashing. Perform “Data setting during Check the data changes to40 6 02 1 camera system adjustment”. “01”. (Refer to page 5-14) 41 6 01 00 Press PAUSE button. Perform “Picture Frame 2 42 6 01 E7 Press PAUSE button. setting”. (Refer to page 5-15) 43 Check the flashing. 3 4 1E Note down the data. Check the data changes to441E 00 44 6 02 “01”. 5 6 2C 01 EA Check that the displayed data6690 00 45 F EC satisfies the Y level specified EE value. 7 6 91 00 46 0 03 2C8692 FF Check that the R-Y level data9693 FF 47 1 (Note 4) satisfies the specified 10 6 6C 01 value. 11 6 01 79 Press PAUSE button. 48 0 03 2D Check the data changes to 12 6 07 Check that the B-Y level data “01”. 49 1 (Note 4) satisfies the specified 13 6 01 67 Press PAUSE button. value. 14 Check the flashing. Note 7: The adjustment data will be automatically input to page: F, address: B6 to B7 and DB to EF. Check the data changes to 15 6 02 “01”. 5-30, Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. 2 6 90 003691 004692 005693 00662C 00766C 008003 00 Set data noted down at step941E 3, and press PAUSE button. Release the data setting 10 performed at step 1. (Refer to page 5-14) 5-31, 21. AF Illumination Check RadarW Check the deviation of optical axis of AF illuminator. Mode CAMERA Subject Flash adjustment box (Note 3) (50 cm or1mfrom the front of lens) Measurement Point Check operation on monitor TV Measuring Instrument Note 1: Perform checking by making the shooting surface of the Flash adjustment box perpendicular to the optical axis of the camera. Note 2: Perform this checking in the Flash adjustment box. Restrict external light to enter the Flash adjustment box as less as possible. Note 3: Refer to “4. Preparing the Flash adjustment box”. (See page 5-7) Switch setting 1) FOCUS (Menu setting) ... MULTI AF Adjusting method: Order Page Address Data Procedure Perform “Data setting during 1 camera system adjustment”. (Refer to page 5-14) Set the following data, and press PAUSE button. 2 9 A9 06: 50 cm 04: 1m3601 EF Press PAUSE button. Check the data changes to4602 “01”. Check the data. 5 F 10 00: Normal 01 to FF: Defective Processing after Completing Adjustment: Order Page Address Data Procedure1601 00 Press PAUSE button. Release the data setting 2 performed at step 1. (Refer to page 5-14) 5-32, 1-5. LCD SYSTEM ADJUSTMENTS [Adjusting connector] Before perform the camera system adjustments, check that the Most of the measuring points for adjusting the LCD system are specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- concentrated in CN706 of the SY-77 board. isfied. Connect the Measuring Instruments via the CPC-9 jig (J-6082- 393-C). Note 1: Taken an extreme care not to destroy the liquid crystal The following table shows the Pin No. and signal name of CN display module by static electricity when replacing it. 903. Note 2: Set the LCD BRIGHTENSS (SET UP setting) to the NORMAL. Pin No. Signal Name Pin No. Signal Name 1 N. C. 10 HI UNREG 2 N. C. 11 LANC IN 3 N. C. 12 LANC OUT 4 REG_GND 13 N. C. 5 CPC_IN 14 N. C. 6 N. C. 15 N. C. 7 HSY 16 N. C. 8 PANEL_COM 17 N. C. 9 VG 18 N. C. CPC-9 jig (J-6082-393-C) (Note 1, 2) CPC cover SY-77 board CN706 Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjusting remote commander. Fig. 5-1-18 5-33, 1. LCD Initial Data Input 2. VCO Adjustment (SW-368 Board) Set the VCO free-run frequency. If deviated, the LCD screen will Mode PLAY be blurred. Signal Arbitrary Mode PLAY Adjustment Page A Signal Arbitrary Adjustment Address 84, 8D Measurement Point Pin 7 of CN706 on SY-77 board (HSY) Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Measuring Instrument Frequency counter 2) Select page: A, and enter the data given in the following table. Adjustment Page A Adjustment Address 82 (NTSC) Note: Press the PAUSE button each time the data are set, as the 83 (PAL) data are written to non-volatile memory (EEPROM). Specified Value T = 15734 ± 30 Hz (NTSC) Address Data Remark T = 15625 ± 30 Hz (PAL) 84 20 V-COM adj. Menu setting: 8D 2F Fixed value 1) VIDEO OUT of SET UP setting ... NTSC (NTSC mode) Processing after Completing Adjustments: (This adjustment must be performed in NTSC mode, so don’t 1) Select page: 0, address: 01, and set data: 00. set the menu setting to “PAL” ) Adjusting method: Order Page Address Data Procedure1001 012A02 03 Press PAUSE button. 3 4 F1 13 (NTSC) 4 4 1D 82 (PAL) Change the data and set the5A82 frequency (f) to the NTSC specified value. 6 A 82 Press PAUSE button. Change the data and set the7A83 frequency (f) to the PAL specified value. 8 A 83 Press PAUSE button. Processing after Completing Adjustments: Order Page Address Data Procedure1A02 00 Press PAUSE button. 2 4 F1 00 (NTSC) 3 4 1D 80 (PAL) 4 0 01 00 5-34, 3. Black Limit Adjustment (SW-368 Board) 4. Bright Adjustment (SW-368 Board) Set the maximum amplitude of the RGB decoder for driving the Set the amplitude of the RGB decoder for driving the LCD to the LCD to the specified value. specified value. If deviated, the LCD screen image will be blackish or saturated If deviated, the LCD screen image will be blackish or saturated (whitish). (whitish). Mode PLAY Mode PLAY Signal Arbitrary Signal Arbitrary Measurement Point Pin 8 of CN706 on SY-77 board Measurement Point Pin 9 of CN706 on SY-77 board (PANEL COM) (VG) Measuring Instrument Oscilloscope External trigger: Pin 8 of CN706 on SY-77 board (PANEL_COM) Adjustment Page A Measuring Instrument Oscilloscope Adjustment Address 86 Adjustment Page A Specified Value A = 8.3 ± 0.1 Vp-p Adjustment Address 85 Adjusting method: Specified Value A = 7.96 ± 0.1 Vp-p Order Page Address Data Procedure Adjusting method: 1 0 01 012A02 03 Press PAUSE button Order Page Address Data Procedure34F1 081001 01 Change the data and set the2A02 03 Press PAUSE button4A86 voltage (A) to the specified34F1 03 value. (Note 1) Change the data and set the5A86 Press PAUSE button. 4 A 85 voltage (A) to the specified Note 1: Adjust it between data 00 and 0F. value. (Note) Note 2: Check that the adjusted value of D range is within speci- 5 A 85 Press PAUSE button. fied value after this adjustment is performed. Note: Adjust it between data 00 and FF. If not, perform the adjustment again. Processing after Completing Adjustments: Processing after Completing Adjustments: Order Page Address Data Procedure Order Page Address Data Procedure1A02 00 Press PAUSE button1A02 00 Press PAUSE button24F1 0024F1 003001 003001 00 Pedestal

A A V

Pedestal 2H Fig. 5-1-19 A: Pedestal level difference between 1H period and previous 1H period. Fig. 5-1-20 5-35, 5. Contrast Adjustment (SW-368 Board) 6. VG Center Adjustment (SW-368 Board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the center of VG signal for driving the LCD to the specified fied value. value. If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitrary Mode PLAY Measurement Point Pin 9 of CN706 on SY-77 board Signal Arbitrary (VG) Measurement Point Pin 9 of CN706 on SY-77 board Measuring Instrument Digital voltmeter (VG) External trigger: Pin 8 of CN706 Adjustment Page A on SY-77 board (PANEL COM) Adjustment Address 8B Measuring Instrument Oscilloscope Specified Value A = 7.00 ± 0.05 Vp-p Adjustment Page A Adjusting method: Adjustment Address 8A ± Order Page Address Data ProcedureSpecified Value A = 2.50 0.05 Vp-p1001 01 Adjusting method: 2 A 02 03 Press PAUSE button Order Page Address Data Procedure34F1 021001 01 Change the data and set the2A02 03 Press PAUSE button4A8B DC voltage (A) to the specified value. (Note) 3 4 F1 035A8B Press PAUSE button. Change the data and set the4A8A voltage (A) to the specified Note: Adjust it between data 00 and 7F. value. (Note) Processing after Completing Adjustments: 5 A 8A Press PAUSE button. Note: Order Page Address Data ProcedureAdjust it between data 00 and 7F. 1 A 02 00 Press PAUSE button Processing after Completing Adjustments: 2 4 F1 00 Order Page Address Data Procedure3001 001A02 00 Press PAUSE button24F1 003001 00 10 steps peak

A

Pedestal 2H A: Between the pedestal and 10 steps peak Fig. 5-1-21 5-36, 7. PSIG Gray Adjustment (SW-368 Board) 8. V-COM Adjustment (SW-368 Board) Set the common electrode drive signal level of LCD to the speci- Set the DC bias of the common electrode drive signal of LCD to fied value. the specified value. If deviated, the LCD display will be move, producing flicker and Mode PLAY conspicuous vertical lines. Signal Arbitrary Mode PLAY Measurement Point Pin 8 of CN706 on SY-77 board Signal Arbitrary (PANEL COM) Measurement Point Measuring Instrument Oscilloscope Check on the LCD screen Measuring Instrument Adjustment Page A Adjustment Page A Adjustment Address 87 ± Adjustment Address 84Specified Value A = 5.0 0.1 Vp-p Specified Value The brightness difference Adjusting method: between the section-A and section-B is minimum Order Page Address Data Procedure Note 1: Perform “Bright Adjustment” and “Contrast Adjustment” 1 0 01 01 before this adjustment. 2 A 02 03 Press PAUSE button34F1 02 Adjusting method: Change the data and set the PSIG Order Page Address Data Procedure4A87 signal level (A) to the specified1001 01 value. (Note) 2 A 02 03 Press PAUSE button5A87 Press PAUSE button. 3 4 F1 82 Note: Adjust it between data 00 and 7F. Change the data so that4A84 Processing after Completing Adjustment: brightness of the section A and section B is equal. Order Page Address Data Procedure Read the data and this data is1A02 00 Press PAUSE button5A84 named Dref. 2 4 F1 00 Convert Dref to decimal3001 00 notation, and obtain Dref’. (Note 2) Calculate D84’ using following equations. (decimal calculation) D84’ = Dref’ – 02 Convert D84’ to a hexadeci- A 8 mal number, and obtain D84. (Note 2) 9 A 84 D84 Press PAUSE button. (Note 3) Note 2: Refer to table 5-2-2. “Hexadecimal-decimal conversion 2H table”. Note 3: Adjust it between data 00 and 3F. Fig. 5-1-22 Processing after Completing Adjustments: Order Page Address Data Procedure1A02 00 Press PAUSE buttton24F1 003001 00BAABBAABFig. 5-1-23 5-37, 9. White Balance Adjustment (SW-368 Board) Correct the white balance. If deviated, the LCD screen color cannot be reproduced. Mode PLAY Signal Arbitrary Measurement Point Check on the LCD screen Measuring Instrument Adjustment Page A Adjustment Address 88, 89 Specified Value LCD screen must not be colored Note 1: Check the white balance only when replacing the fol- lowing parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC801 Adjusting method: Order Page Address Data Procedure1001 012A02 03 Press PAUSE button34F1 02 Press PAUSE button. 4 A 88 94 (Initial value) Press PAUSE button. 5 A 89 7A (Initial value) Check that the LCD screen is not colored. If not colored, 6 proceed to “Processing after Completing Adjustments”. 88 Change the data so that the7ALCD screen is not colored. 89 (Note 2) Note 2: To write in the non-volatile memory (EEPROM), press the PAUSE button each time to set the data. Processing after Completing Adjustments: Order Page Address Data Procedure1A02 00 Press PAUSE button24F1 003001 00 5-38, 5-2. SERVICE MODE • Changing the address 2-1. ADJUSTING REMOTE COMMANDER The address increases when the FF (M) button is pressed, The adjusting remote commander is used for changing the calcu- and decreases when the REW (M) button is pressed. There lation coefficient in signal processing, EVR data, etc. The adjust- are altogether 256 addresses, from 00 to FF. ing remote commander performs bi-directional communication • Changing the data (Data setting) with the unit using the remote commander signal line (LANC). The data increases when the PLAY (N) button is pressed, The resultant data of this bi-directional communication is written and decreases when the STOP (x) button is pressed. There in the non-volatile memory. are altogether 256 data, from 00 to FF. • Writing the adjustment data 1. Used the Adjusting Remote Commander The PAUSE button must be pressed to write the adjustment 1) Connect the adjusting remote commander to the CN706 on data in the nonvolatile memory. (The new adjustment data the SY-77 Board via CPC-9 jig (J-6082-393-C). will not be recorded in the nonvolatile memory if this step is 2) Set the HOLD switch of the adjusting remote commander to not performed) “HOLD” (SERVICE position). 3) Turn on the power with the POWER switch of the unit. 2. Precautions upon Using the Adjusting Remote If it has been properly connected, the LCD on the adjusting re- Commander mote commander will display as shown in Fig. 5-2-1. Mishandling of the adjusting remote commander may erase the correct adjustment data at times. To prevent this, it is recommended that all adjustment data be noted down before beginning adjust- ments and new adjustment data after each adjustment. 0 : 00 : 00 Page Data Address Fig. 5-2-1 4) Operate the adjusting remote commander as follows. • Changing the page The page increases when the EDIT SEARCH + button is pressed, and decreases when the EDIT SEARCH – button is pressed. There are altogether 16 pages, from 0 to F. Hexadecimal0123456789ABCDEFnotation LCD Display0123456789AbcdEFDecimal notation0123456789101112131415 conversion value Table 5-2-1 5-39, 2-2. DATA PROCESS The calculation of the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-2-2. indicates the hexadecimal notation- the deci- mal notation, calculation table. Hexadecimal nontation-Decimal notation 2 ↓ The lower digits of the0123456789ABCDEFhexadecimal notation The upper digits of the (A) (b) (c) (d) (E) (F) hexadecimal notation0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 1→ B (b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note : ( ) indicate the adjusting remote control unit display. (Example) In the case that the adjusting remote control unit display are BD (bd). As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection “189” of the1 and 2 in the above table is the decimal notation to be calculated. Table 5-2-2 5-40, 2-3. SERVICE MODE 3. Mode Dial Check (1) 1. Setting the Test Mode Page 2 Address 90 Page D Address 21 Data Function Data Function 00 to 14 MOVIE 00 Normal 15 to 3D SCN 02 Forced MOVIE mode power ON 3E to 67 CAMERA 03 Forced CAMERA mode power ON 08 Forced PLAY mode power ON Using method: • Before setting the data, select page: 0, address: 01, and set data: 1) Select page: 2, address: 90. 01. 2) By discriminating the bit value of dispaly data, the state of the • For page D, the data set is recorded in the non-volatile memory switches can be discriminated. by pressing the PAUSE button of the adjusting remote com- mander. In this case, take note that the test mode will not be 4. Mode Dial Check (2) exited even when the main power is turned off. • After completing adjustments/repairs, be sure to return the data Page 2 Address 80, 81 of this address to “00”, and press the PAUSE button of the ad- justing remote commander. Select page: 0, address: 01, and set data: 00. Address Bit Function When bit When bit value=1 value=0 80 1 PLAY others PLAY 2. Bit Value Discrimination Bit values must be discriminated using the display data of the ad- 81 4 SET UP others SET UP justing remote commander for following items. Use the table be- low to discriminate if the bit value is “1” or “0”. Using method: 1) Select page: 2, address: 80 and 81. Display on the adjustilng remote commander 2) By discriminating the bit value of dispaly data, the state of the switches can be discriminated. 0 : 00 : 00 5. Switch Check (1) Page 2 Address 80 Address Page bit3 to bit0 discrimination Bit Function When bit value=1 When bit value=0 bit7 to bit4 discrimination POWER SW 0 (CONTROL OFF ON Display on the Bit values SWITCH BLOCK) Adjusting bit3 bit2 bit1 bit0 1 remote or or or or 2 commander bit7 bit6 bit5 bit4 Shutter button00000(XSHTR ON) 3 OFF ON10001(CONTROL SWITCH20010BLOCK) 30011Shutter button (XAE LOCK ON) 401004OFF ON(CONTROL SWITCH50101BLOCK) 601105MEMORY STICK OUT IN70111IN SW (MS Socket) A81000Using method: 910011) Select page: 2, address: 80. A (A) 10102) By discriminating the bit value of dispaly data, the state of the B (b) 1011switches can be discriminated. C (c) 1100D(d) 1101BE(E) 1110F(F) 1111Example: If “8E” is displayed on the adjusting remote com- mander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. 5-41, 6. Switch Check (2) Page 2 Addresses 91, 92, 94 Using method: 1) Select page: 2, addresses: 91, 92 and 94. 2) By discriminating the dispaly data, the pressed key can be discriminated. Data Address 00 to 0C 0D to 27 28 to 48 49 to 73 74 to A5 A6 to DC DD to FF CONTROL DOWN CONTROL UP 91 MENU (SELFTIMER) (STROBO) (KEY AD0) (SW-368 board) (SW-368 board) (SW-368 board) (IC404 tg) (S003) (S004) (S004) CONTROL RIGHT CONTROL LEFT DISPLAY/LCD 92 CONTROL SET (MACRO) (REVIEW) ON/OFF (KEY AD1) (SW-368 board) (SW-368 board) (SW-368 board) (SW-368 board) (IC404 th) (S004) (S004) (S004) (S005) 94 ZOOM (W) ZOOM (T) (KEY AD3) (SW-368 board) (SW-368 board) (IC404 tk) (S001) (S002) 7. LED Check Page 2 Address 04 Data 02 Using method: 1) Select page: 2, address: 04, set data: 02, and press the PAUSE button of the adjusting remote commander. 2) Check that all LED except for the ACCESS LED are lit and all segments of LCD (display window) are lit. 3) Select page: 2, address: 04, set data: 00 and press the PAUSE button of the adjusting remote commander. 8. Self Diagnosis Code Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61: Checking of lens drive circuit. When failed in the focus and zoomss initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. 55-4-422 E,

SECTION 6

COVER REPAIR PARTS LIST 6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • Accessories are given in the last of the electrical Replace only with part number speci- have some difference from the original one. parts list. fied. • Items marked “*” are not stocked since they are Les composants identifiés par une seldom required for routine service. Some delay marque 0 sont critiquens pour la should be anticipated when ordering these items. sécurité. • The mechanical parts with no reference number in Ne les remplacer que par une pièce portant le numéro spécifié. the exploded views are not supplied. 6-1-1. CABINET (FRONT) SECTION ns: not supplied 3 ns Ref. No. Part No. Description Ref. No. Part No. Description 1 X-3952-493-1 CABINET (FRONT) ASSY 3 3-064-225-01 LID, CPC 2 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 6-1, 6-1-2. CABINET (REAR) ASSEMBLY ns: not supplied 52 56 51 53 54 55 ns 57 Ref. No. Part No. Description Ref. No. Part No. Description 51 1-477-235-11 SWITCH BLOCK, CONTROL 57 3-075-821-01 LCD WINDOW (1.5) 52 3-075-824-01 COVER, MODE DIAL 58 3-075-822-01 SHEET (1.5), ADHESIVE 53 X-3952-494-1 CABINET (REAR) ASSY 59 X-3952-492-1 CABINET (LOWER) ASSY 54 3-075-831-01 COVER, JACK 60 3-070-999-01 FOOT (UN), RUBBER 55 3-071-051-01 BUTTON, FUNCTION 61 3-831-441-11 TAPE (K) 56 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 6-2, 6-1-3. LENS BLOCK AND LCD SECTION ns: not supplied ns LCD901 D901 ! 107102 105 121 ns 118 ns 102 117 122 115 MIC901 IC101 114 (Note) 106 110 111 113 ! : BT001 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-35.) (Note) Be sure to read “Precuations for Replacement of CCD Imager” on page 4-8 when changing the CCD imager. The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Ref. No. Part No. Description 101 A-7078-329-A SY-77 BOARD, COMPLETE (SERVICE) 114 3-070-143-01 PLATE, LIGHT INTERCEPTION 102 3-713-791-71 SCREW (M1.7X4) 115 3-054-555-01 RUBBER (K), SEAL 103 3-071-017-01 SHEET (STROBOSCOPE), INSULATING 117 A-7078-260-A CD-397 BOARD, COMPLETE 104 A-7078-259-A ST-70 BOARD, COMPLETE 118 3-713-791-11 SCREW (1.7X5), TAPPING, P2 105 3-075-819-01 FRAME, LENS 119 3-071-033-01 HOLDER, LED 106 3-075-827-01 COVER, CUSHION MICROPHONE 120 3-075-826-01 CASE, MICROPHONE 107 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 121 3-077-192-01 SHEET (CD), PROTECTION 108 3-071-019-01 SHEET, PROTECTION 122 3-831-441-11 TAPE (K) 109 1-758-773-11 LENS, ZOOM (CE01B) 0D901 1-477-303-11 BLOCK LIGHT GUIDE PLATE * 110 3-055-971-01 CUSHION, MICROPHONE IC101 A-7095-114-A CCD BLOCK ASSY (Note) 111 3-075-825-01 COVER, MICROPHONE LCD901 8-753-051-66 ACX309AKA-1 112 3-070-998-01 CUSHION (LCD), INTERCEPTION MIC901 1-542-446-31 MICROPHONE 113 1-758-773-11 FILTER BLOCK, OPTICAL 6-3, 6-1-4. BATTERY HOLDER ASSEMBLY ns: not supplied BT901 161 154 156 157 ns 155 ns 156 (Note) ns ns 156 156 ns 161 (Note) Including the parts mounted on JK-226 board. Ref. No. Part No. Description Ref. No. Part No. Description 151 1-684-891-11 FP-478 FLEXIBLE BOARD 157 3-071-008-01 SP HOLDER 152 1-815-853-13 CONNECTOR, MEMORY STICK 158 A-7078-258-A SW-368 BOARD, COMPLETE 153 3-075-839-01 LID, BT 159 A-7078-257-A JK-227 BOARD, COMPLETE (Note) 154 X-3952-491-1 HOLDER ASSY, BATTERY 160 3-071-013-01 SP CUSHION 155 3-318-382-01 SCREW (1.7X3), TAPPING 161 3-713-791-71 SCREW (M1.7X4) 156 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 BT901 1-694-854-11 BATTERY TERMINAL BOARD 6-4,

CD-397

6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service. mark 0 or dotted line with mark 0 are critical for safety. fied in the diagrams or the components used Some delay should be anticipated when order- Replace only with part number on the set. ing these items. specified. • -XX and -X mean standardized parts, so they • SEMICONDUCTORS Les composants identifiés par une may have some difference from the original In each case, u: µ, for example: marque 0 sont critiquens pour la one. uA.: µA.uPA.: µPA.sécurité. • RESISTORS uPB.: µPB.uPC.: µPC.Ne les remplacer que par une pièce All resistors are in ohms. uPD.: µPD.portant le numéro spécifié. METAL: Metal-film resistor. • CAPACITORS METAL OXIDE: Metal oxide-film resistor. uF: µF When indicating parts by reference F: nonflammable • COILS number, please include the board. uH: µH • Abbreviation AUS : Australian model KR : Korean model CH : Chinese model JE : Tourist model CND : Canadian model J : Japanese model HK : Hong Kong model Ref. No. Part No. Description Ref. No. Part No. Description A-7078-260-A CD-397 BOARD, COMPLETE < THERMISTOR > *********************** (IC101 is not included in this board) TH101 1-810-816-11 THERMISTOR, NTC (1608) < CAPACITOR > C101 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Electrical parts list of the JK-227 board is C103 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V not shown. C104 1-135-957-91 TANTAL. CHIP 10uF 20% 16V Page 6-6 is not shown. C105 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V C106 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C107 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C108 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C109 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < DIODE > D101 6-500-102-01 DIODE TLOH20TP (SONY2) < IC > IC101 A-7095-114-A CCD BLOCK ASSY (CCD IMAGER) (Note) < FERRITE BEAD > FB101 1-414-228-11 FERRITE 0uH < TRANSISTOR > Q101 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1) Q102 8-729-052-64 TRANSISTOR DTC144EHT2L < RESISTOR > R101 1-216-864-11 METAL CHIP 0 5% 1/16W R102 1-216-807-11 METAL CHIP 68 5% 1/16W R103 1-216-864-11 METAL CHIP 0 5% 1/16W R104 1-216-864-11 METAL CHIP 0 5% 1/16W R105 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R106 1-216-801-11 METAL CHIP 22 5% 1/16W R107 1-216-849-11 METAL CHIP 220K 5% 1/16W R108 1-216-826-11 METAL CHIP 2.7K 5% 1/16W (Note) Be sure to read “Note on the CCD Imager Replacement” on page 4-7 when changing the CCD imager. 6-5,

ST-70 SW-368

Ref. No. Part No. Description Ref. No. Part No. Description A-7078-259-A ST-70 BOARD, COMPLETE C115 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V *********************** C116 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V C117 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V 0 1-477-329-11 FLASH UNIT C118 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V C119 1-125-838-11 CERAMIC CHIP 2.2uF 10% 6.3V < BATTERY > C120 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V BT001 1-756-191-21 BATTERY, LITHIUM (SECONDARY) C121 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C122 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V < CAPACITOR > C123 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C124 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C001 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C002 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C125 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V 0C003 1-165-943-11 ELECT 135uF 315V C126 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V 0C004 1-137-723-21 CERAMIC CHIP 0.047uF 10% 250V < CONNECTOR > < DIODE > CN101 1-794-766-21 CONNECTOR, FFC/FPC (LIF) 6P D001 8-719-056-23 DIODE MA2S111- (K8).SO CN102 1-794-770-11 CONNECTOR, FFC/FPC (LIF) 24P 0D002 6-500-237-01 DIODE HAU160C030TP < DIODE > < COIL > D001 8-719-075-15 DIODE MAZT082H08S0 0L001 1-424-770-11 COIL, TRIGGER D002 8-719-077-34 DIODE SML-310YTT86 (STROBO/CHARGE LED) < TRANSISTOR > D003 8-719-063-83 DIODE CL-196YG-CD-T (AE LOCK (GREEN)) D004 8-719-077-09 DIODE CL-196HR-CD-T (TALLY (RED)) Q001 8-729-422-87 TRANSISTOR 2SB1073-R-TX D005 8-719-075-15 DIODE MAZT082H08S0 0Q002 8-729-053-74 TRANSISTOR CY25AAJ-8-T13 D006 8-719-075-15 DIODE MAZT082H08S0 < RESISTOR > D007 8-719-075-15 DIODE MAZT082H08S0 D101 8-719-084-47 DIODE 1SV290 (TPL3) R001 1-216-805-11 METAL CHIP 47 5% 1/16W D102 8-719-017-82 DIODE MA8036-TX R002 1-216-838-11 METAL CHIP 27K 5% 1/16W R003 1-216-826-11 METAL CHIP 2.7K 5% 1/16W < IC > R004 1-216-814-11 METAL CHIP 270 5% 1/16W R005 1-216-805-11 METAL CHIP 47 5% 1/16W IC101 8-759-660-93 IC RB5P004AM1 IC102 8-752-407-33 IC CXD3512R-T4 R006 1-216-857-11 METAL CHIP 1M 5% 1/16W IC103 6-700-270-01 IC TC75S55FU (TE85R) 0R007 1-216-121-11 RES-CHIP 1M 5% 1/10W < COIL > < TRANSFORMER > L101 1-469-846-21 INDUCTOR 47uH 0T001 1-435-741-21 TRANSFORMER, DC-DC CONVERTER L102 1-469-757-21 INDUCTOR 10uH L103 1-412-949-21 INDUCTOR 6.8uH L104 1-469-846-21 INDUCTOR 47uH A-7078-258-A SW-368 BOARD, COMPLETE *********************** < TRANSISTOR > < CAPACITOR > Q002 8-729-427-72 TRANSISTOR HN1C01FU-TE85R Q003 8-729-427-70 TRANSISTOR HN1A01FU-TE85R C002 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V Q004 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C101 1-125-839-91 TANTAL. CHIP 47uF 20% 6.3V Q101 8-729-427-74 TRANSISTOR XP4601-TXE C102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q102 8-729-427-74 TRANSISTOR XP4601-TXE C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C104 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q103 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO Q104 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C105 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q105 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C106 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q106 8-729-042-26 TRANSISTOR 2SB1462J-QR (K8).SO C107 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q107 8-729-056-00 TRANSISTOR MCH3310-TL-E C108 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C109 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V Q108 8-729-042-26 TRANSISTOR 2SB1462J-QR (K8).SO Q109 8-729-042-26 TRANSISTOR 2SB1462J-QR (K8).SO C110 1-137-706-11 TANTAL. CHIP 4.7uF 20% 20V C111 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < RESISTOR > C112 1-164-739-11 CERAMIC CHIP 560PF 5% 50V C113 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R002 1-218-883-11 METAL CHIP 33K 0.5% 1/10W C114 1-162-926-11 CERAMIC CHIP 82PF 5% 50V R003 1-218-904-11 METAL CHIP 240K 0.5% 1/10W R005 1-216-845-11 METAL CHIP 100K 5% 1/16W The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-7 ber specified. portant le numéro spécifié.,

SW-368

Ref. No. Part No. Description Ref. No. Part No. Description R006 1-216-845-11 METAL CHIP 100K 5% 1/16W R007 1-216-818-11 METAL CHIP 560 5% 1/16W R008 1-216-815-11 METAL CHIP 330 5% 1/16W R009 1-216-820-11 METAL CHIP 820 5% 1/16W R010 1-216-822-11 METAL CHIP 1.2K 5% 1/16W R011 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R012 1-216-822-11 METAL CHIP 1.2K 5% 1/16W R013 1-216-822-11 METAL CHIP 1.2K 5% 1/16W R014 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R015 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R018 1-216-817-11 METAL CHIP 470 5% 1/16W R104 1-216-839-11 METAL CHIP 33K 5% 1/16W R105 1-216-839-11 METAL CHIP 33K 5% 1/16W R106 1-216-853-11 METAL CHIP 470K 5% 1/16W R107 1-216-835-11 METAL CHIP 15K 5% 1/16W R108 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R109 1-216-841-11 METAL CHIP 47K 5% 1/16W R110 1-216-843-11 METAL CHIP 68K 5% 1/16W R111 1-216-837-11 METAL CHIP 22K 5% 1/16W R112 1-216-843-11 METAL CHIP 68K 5% 1/16W R113 1-216-857-11 METAL CHIP 1M 5% 1/16W R114 1-216-845-11 METAL CHIP 100K 5% 1/16W R115 1-216-797-11 METAL CHIP 10 5% 1/16W R116 1-216-797-11 METAL CHIP 10 5% 1/16W R117 1-216-797-11 METAL CHIP 10 5% 1/16W R118 1-216-797-11 METAL CHIP 10 5% 1/16W R119 1-216-845-11 METAL CHIP 100K 5% 1/16W R120 1-216-845-11 METAL CHIP 100K 5% 1/16W R121 1-216-845-11 METAL CHIP 100K 5% 1/16W R122 1-216-845-11 METAL CHIP 100K 5% 1/16W R123 1-218-869-11 METAL CHIP 8.2K 0.5% 1/10W R124 1-216-833-11 METAL CHIP 10K 5% 1/16W R125 1-218-855-11 METAL CHIP 2.2K 0.5% 1/10W R126 1-216-833-11 METAL CHIP 10K 5% 1/16W R127 1-216-853-11 METAL CHIP 470K 5% 1/16W R128 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R129 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R130 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R131 1-218-911-11 METAL CHIP 470K 0.5% 1/10W R132 1-218-881-11 METAL CHIP 27K 0.5% 1/10W R133 1-211-989-11 METAL CHIP 68 0.5% 1/10W R134 1-216-842-11 METAL CHIP 56K 5% 1/16W R135 1-216-847-11 METAL CHIP 150K 5% 1/16W R136 1-211-989-11 METAL CHIP 68 0.5% 1/10W R137 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R138 1-218-887-11 METAL CHIP 47K 0.5% 1/10W R139 1-216-821-11 METAL CHIP 1K 5% 1/16W < SWITCH > S001 1-786-157-11 SWITCH, TACTILE (ZOOM (W)) S002 1-786-157-11 SWITCH, TACTILE (ZOOM (T)) S003 1-786-157-11 SWITCH, TACTILE (MENU) S004 1-786-039-21 SWITCH, TACTILE (CONTROL) S005 1-786-157-11 SWITCH, TACTILE (DISPLAY)

Electrical parts list of the SY-77 board is not

shown.

Pages 6-9 to 6-13 are not shown.

6-8, Ref. No. Part No. Description Ref. No. Part No. Description

ACCESSORIES

************ 0 1-476-332-11 ADAPTOR, AC (AC-LSI) (US, CND, KR, JE, J) 0 1-476-332-23 ADAPTOR, AC (AC-LSI) (CH) 0 1-476-332-43 ADAPTOR, AC (AC-LSI) (AEP, UK, E, HK) 0 1-569-007-11 ADAPTOR, CONVERSION (E, JE) 0 1-569-008-21 ADAPTOR, CONVERSION 2P (E) 0 1-696-819-11 CORD, POWER (AUS) 0 1-769-608-11 CORD, POWER (AEP, E) 0 1-782-476-11 CORD, POWER (CH) 0 1-783-374-11 CORD, POWER (UK, HK) 0 1-790-107-22 CORD, POWER (US, CND, KR) 0 1-790-732-11 CORD, POWER (JE, J) 1-823-932-11 CORD, CONNECTION (USB 5P) 1-824-111-11 CORD, CONNECTION (AV CONNECTING 1.5m) 3-050-664-11 STRAP, HAND 3-065-665-01 MANUAL, INSTRUCTION (JAPANESE) (J) 3-072-414-01 SPVD-008 (CD-ROM) (EXCEPT US, CND, KR, J) 3-072-654-01 SPVD-008 (I) (CD-ROM) (US, CND, KR, J) 3-075-412-01 MANUAL, INSTRUCTION (JAPANESE) (J) 3-075-412-11 MANUAL, INSTRUCTION (ENGLISH) (EXCEPT J) 3-075-412-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) (CND, AEP) 3-075-412-31 MANUAL, INSTRUCTION (SWEDISH, PORTUGUESE) (AEP, E, JE) 3-075-412-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (AEP) 3-075-412-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 3-075-412-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (AEP) 3-075-412-71 MANUAL, INSTRUCTION (ARABIC) (E) 3-075-413-01 MANUAL, INSTRUCTION (JAPANESE) (J) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. 66-1-144E, FOR CAMERA COLOR REPRODUCTION ADJUSTMENT Take a copy of CAMERA COLOR REPRODUCTION FRAME with a For NTSC mode clear sheet for use. R-Y

MG R YE

B-Y

B G CY

✄ DSC-P9 — 113 — ✄, 9-929-973-31 Sony EMCS Co. 2002D0500-1 ©2002.4 — 114 — Published by DI Customer Center,

Reverse 992997331.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2002.04 Official Release — —]
15

Similar documents

For the Customers in the U.S.A. Notice on the supplied battery Certain countries may regulate disposal of the battery used to power this product.
DSC-P92 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Korea Model Chinese Model Tourist Model Brazilian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUA
Note: This equipment has been tested and found to For the Customers in the U.S.A.
DSC-P93 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2004.03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Argentine Model Brazilian Model Tourist Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUA
DSC-R1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005.10 Canadian Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model
DSC-R1 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005.10 Canadian Model Revision History AEP Model UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS ACCESSORIES INSTRUCTION MANUAL SERVICE NOTE The components identified by Les c
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2005.11 Canadian Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2005.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link FRAME SCHEMATIC DIAGRAM PRINTED WIRING BOARDS REPAIR PARTS LIST SCH
DSC-R1 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005.10 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.2 2006.05 Canadian Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 3 US Model Ver 1.2 2006.05 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link FRAME SCHEMATIC DIAGRAM PRINTED WIRING BOARDS REPAIR PARTS LIST SCH
SAFETY-RELATED COMPONENT WARNING!!
DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.3 2004. 07 Photo: DSC-S30 SPECIFICATIONS System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚C to 40˚C) (–20˚C to +60˚C) Minij
SAFETY-RELATED COMPONENT WARNING!!
DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.1 2000. 09 With SUPPLEMENT-1 (9-929-819-81) Photo: DSC-S30 SPECIFICATIONS System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚
- : Points changed portion.
DSC-S30/S50 US Model Canadian Model SERVICE MANUAL AEP ModelUK Model Level2EModel Hong Kong Model Ver 1.3 2004. 07 Australian Model Chinese Model Korea Model Tourist Model Japanese Model CORRECTION-1 File this correction with the service manual. • Correction of SCHEMATIC DIAGRAMS • Correction of EXP
DSC-R1 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
Supplied accessories
DSC-S30/S50 SERVICE MANUAL US Model Ver 1.1 2000. 09 Canadian ModelLevel 2 With SUPPLEMENT-1(9-929-819-82) AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model as
! : Points deleted portion.
DSC-S40 Auto-ADJ SERVICE MANUAL Ver 1.1 2005.11 CORRECTION-1 We will inform you that there are printing errors in the service manual previously issued. • Correction of the Before starting adjustment • Correction of the Table 6-1-1 • Correction of the Service tool DSC-S40 2005K0500-1© 2005.11 9-876-8
& : Points added portion.
DSC-S40 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.2 2005.09 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model SUPPLEMENT-1 Tourist Model File this supplement with the service manual. (PV05-041) • Change of Repair Parts Suffix No. of ST-11
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.06 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
TABLE OF CONTENTS
DSC-S30/S50 SERVICE MANUAL US Model Canadian Model Level 3 Ver 1.1 2000. 09 With SUPPLEMENT 1 AEP Model (9-929-819-83) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model a
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS [System] USB communication
DSC-S45 SERVICE MANUAL US Model Ver 1.0 2006.03 Revision History How to use Acrobat Reader Internal memory ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont cr
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.2 2006.09 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.1 2006.07 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
SAFETY CHECK-OUT
DSC-S600 SERVICE MANUAL LEVEL 3 US Model Ver. 1.1 2006. 07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SERVICE NOTE SCHEMATIC DIAGRAMS REPAIR PARTS LIST F
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model E Model Australian Model Chinese Model Brazilian Model Hong Kong Model Korea Model Link SPECIFICATIONS ACCESSORIES SELF-DIAGNOSIS FUNCTION INSTRUCTION MANUAL Note : Note : The components iden
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 1 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/Silver Argentine Model Lin
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.0 2005.03 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.2 2001.07 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service
SAFETY-RELATED COMPONENT WARNING!!
DSC-S75 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.2 2001. 11 SPECIFICATIONS System Flash General AC-L10A/B/C Accessories Image device Recommended recording Used battery pack AC power adaptor A/V connecting cable (1) 8.93 mm (1/1.8 type) color distance (ISO is set to AUTO): NP-FM50 Power requir
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.3 2002.09 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service