Download: SAFETY-RELATED COMPONENT WARNING!!

DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.3 2004. 07 Photo: DSC-S30 SPECIFICATIONS System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚C to 40˚C) (–20˚C to +60˚C) Minijack Storage temperature Maximum dimensions Lens 3 × zoom lens Video: 1 Vp-p, 75 ohms, –4˚F to +140˚F 5× 1 9/16 ×2 1/2 inches unbalanced, sync negative (–20˚C to +60˚C) (125 ×39 ×62 mm) (w/h/d) f = 6.1 – 18.3 mm Mass (39 – 117 mm when converted Audio: 327 mV (at a Maximum dimensions Approx. 10 oz (28...
Author: Acal1978 Shared: 8/19/19
Downloads: 414 Views: 3933

Content

DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.3 2004. 07

Photo: DSC-S30

SPECIFICATIONS

System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚C to 40˚C) (–20˚C to +60˚C) Minijack Storage temperature Maximum dimensions Lens 3 × zoom lens Video: 1 Vp-p, 75 ohms, –4˚F to +140˚F 5× 1 9/16 ×2 1/2 inches unbalanced, sync negative (–20˚C to +60˚C) (125 ×39 ×62 mm) (w/h/d) f = 6.1 – 18.3 mm Mass (39 – 117 mm when converted Audio: 327 mV (at a Maximum dimensions Approx. 10 oz (280 g) into a 35 mm still camera) 47 kilohm load) 4 1/2 ×2 3/4 ×2 3/4 inches Output impedance: (113 ×68 ×69 mm) (w/h/d) NP-FM50 battery pack F = 2.8 – 2.9 Exposure control 2.2 kilohms Mass Used battery Automatic exposure VIDEO OUT Approx. 13 oz (370 g) Lithium ion battery White balance (DSC-S30 only) (including battery pack NP- Maximum voltage DC 8.4 V Automatic, Indoor, Outdoor, Minijack FM50, “Memory Stick”, wrist Hold Digital I/O (USB) strap and lens cap etc.) Nominal voltage Special minijack Built-in microphone DC 7.2 V Data system Still: JPEG, GIF (in TEXT (DSC-S50 only) Capacity LCD screen mode), TIFF Electret condenser microphone 8.5 Wh (1 180mAh)Used LCD panel Movie (DSC-S50 only): Built-in speaker 2 type TFT (Thin Film MPEG1 (DSC-S50 only) Transistor active matrix) drive Design and specifications are Audio with still image Dynamic speaker subject to change without (DSC-S50 only): Total number of dots MPEG1 (Monaural) 123 200 (560 ×220) dots AC-L10 AC power notice. adaptor Recording medium General Power requirements “Memory Stick” Used battery pack 100 to 240 V AC, 50/60 Hz Flash NP-FM50 Rated output voltage Recommended recording Power requirements DC 8.4 V, 1.5 A in operating distance: 8.4 V mode 11 7/8 inches to 8 1/4 feet Power consumption (0.3 m to 2.5 m) Operation temperature (during recording) 32˚F to 104˚F (0˚C to 40˚C) 2.9 W

DIGITAL STILL CAMERA

, SAFETY-RELATED COMPONENT WARNING!! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-sol- 4. Look for parts which, though functioning, show obvious signs dered connections. Check the entire board surface for solder of deterioration. Point them out to the customer and recom- splashes and bridges. mend their replacement. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. “pinched” or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, particularly transis- • Keep the temperature of the soldering iron around 270 ˚C tors, that were installed during a previous repair. Point them during repairing. out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when sol- dering or unsoldering. – 2 –,

TABLE OF CONTENTS

Section Title Page SERVICE NOTE Self-diagnosis Display ... 4 1. MAIN PARTS 1. Ornamental Parts ... 5 2. DISASSEMBLY 2-1. PD-127 Board and Indicator Module ... 6 2-2. Front Cabinet Block Assembly ... 7 2-3. Battery Lid Assembly and Control Switch Block ... 7 2-4. Flash Unit and Upper Cabinet Block ... 8 2-5. MS-50 Board and BT Holder Assembly ... 8 2-6. Lens Block Assembly ... 9 2-7. SY-58 Board, DD-141 Board and JK-194 Board ... 9 2-8. Control Switch Block and SW-339 Board ... 10 2-9. Hinge Assembly and KJ-11 Board ... 10 3. REPAIR PARTS LIST 3-1. Exploded Views 3-1-1. Front Panel Section ... 11 3-1-2. Main Section ... 12 3-1-3. Rear Cabinet Section ... 13 3-1-4. Lens Block Assembly ... 14 4. GENERAL Identifying the Parts ... 15 Preparing the Power Supply ... 16 Setting the Date and Time ... 17 Inserting the “Memory Stick” ... 18 Recording Still Images ... 18 Recording Moving Images (DSC-S50 only) ... 19 Playing Back Still Images ... 19 Playing Back Moving Images ... 19 Viewing Images Using a Personal Computer ... 20 Image File Storage Destinations and Image Files ... 21 Before Performing Advanced Operations ... 21 Various Recording ... 23 Various Playback ... 25 Editing ... 26 Precautions ... 27 On “Memory Sticks” ... 28 Using Your Camera Abroad ... 28 Troubleshooting ... 28 Warning and Notice Messages ... 29 Self-diagnosis Display ... 29 LCD Screen Indicators ... 30 – 3 –,

SERVICE NOTE

[Description on Self-diagnosis Display] Self-diagnosis display • C: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61: When failed in the focus and zoomss Checking of lens drive circuit. initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. – 4 –,

DSC-S30/S50

1. MAIN PARTS Note: • Items marked “*” are not stocked since they are seldom required for routine service. The components identified by mark 0 or dotted Some delay should be anticipated when ordering these items. line with mark 0 are critical for safety. • The parts numbers of such as a cabinet are also appeared in this section. Replace only with part number specified. Refer to the parts number mentioned below the name of parts to order. 1. ORNAMENTAL PARTS Wrist strap 3-056-776-01 DC cover CPC lid 3-061-111-01 3-060-251-01 Lens cap assembly JK lid X-3950-660-2 3-061-096-01 Cap string 3-061-217-01

Checking supplied accessories.

Check that the following accessories are supplied with your digital still camera. Power cord (1) AC adaptor (1) AV connecting cable (1.5m) (1) USB cable (1) 0 1-769-608-11 (AEP) 0 1-475-599-11 1-783-738-31 (S50) 1-791-785-11 0 1-783-374-11 (UK) Lens cap assembly (1) Cap string (1) Wrist strap (1) Bundle soft (2000) (1) X-3950-660-2 3-061-217-01 3-056-776-01 3-060-716-01

Other accessories

3-060-523-11 MANUAL, INSTRUCTION (ENGLISH) 3-060-523-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) (AEP) 3-060-523-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (AEP) 3-060-523-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (AEP) Video connection cable (1.5 m) (1) 3-060-523-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (AEP) 1-792-955-11 (S30) – 5 –,

DSC-S30/S50

2. DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. PD-127 BOARD AND DSC-S30/S50 INDICATOR MODULE (page 6) 2-2. FRONT CABINET BLOCK

ASSEMBLY

(page 7) 2-3. BATTERY LID ASSEMBLY 2-5. MS-50 BOARD AND AND CONTROL SWITCH BT HOLDER ASSEMBLY BLOCK (page 7) (page 8) 2-4. FLASH UNIT AND 2-6. LENS BLOCK ASSEMBLY UPPER CABINT BLOCK (page 9) (page 8) 2-7. SY-58 BOARD, DD-141 BOARD AND JK-194 BOARD (page 9) 2-8. CONTROL SWITCH BLOCK 2-9. HINGE ASSEMBLY AND AND SW-339 BOARD KJ-11 BOARD (page 10) (page 10) Note: Follow the disassembly procedure in the numerical order given. 2-1. PD-127 BOARD AND INDICATOR MODULE 8 Flexible board 7 Flexible board (CN851) (CN901) 0 PD-127 board and 9 Two claws qg Indicator module inverter transformer unit qs Screw qf Cold cathode (1.7 × 4) fluorescent tube5Pcabinet (Rear) 4 Two claws qa Two connectors (CN801, 802) 1 Screw (M2) qd Two screws (M1.7) 3 Two screws 2 Screw (M2) (M2) 6 Screw (M1.7) Display block Note: In removing 3 two screws, rotate the display block. – 6 –, 2-2. FRONT CABINET BLOCK ASSEMBLY 5 Two screws 6 Two screws × (2 × 4)(2 4) 1 Open the battery lid assembly. 9 Connector (CN706) 8 Flexible board (CN707) 4 Screw qa CPC lid (2 × 4) BT holder assembly 0 Two connectors (CN710, 712) (S50) 2 Screw 0 Connector (2 × 4) (CN712) (S30) 7 Front cabinet block assembly CPC lid 3 Screw (2 × 4) Note: In removing the CPC lid, start from the upper side. 2-3. BATTERY LID ASSEMBLY AND CONTROL SWITCH BLOCK 4 Remove the control switch block (Mode SW) in the direction 3 Screw of arrow A. (1.7 × 4) Note: In mounting the control switch block (Mode SW), 1 Battery lid align the mode SW konb assembly A with the sleeve knob. 2 Screw (1.7 × 4) Sleeve – 7 –, 2-4. FLASH UNIT AND UPPER CABINET BLOCK 1 Two screws (1.7 × 4) 3 Upper cabinet block Capacitor 4 Flash unit Note: Do not touch the capacitor terminals. You could get an electric shock. 2 Claw 8 Speaker (S50) 5 Buzzer (S30) 7 Microphone unit 6 MISP holder 5 Three screws (1.7 × 4) (S50) 2-5. MS-50 BOARD AND BT HOLDER ASSEMBLY 0 DC-IN connector 1 Connector (CN001) 9 BT holder 8 Screw assembly (1.7 × 4) 4 MS-50 board 3 Three screws (1.7 × 4) 7 Screw (1.7 × 4) 5 Connector (CN005) 6 Connector (CN002) 2 FP-024 flexible board (CN003) – 8 –, 2-6. LENS BLOCK ASSEMBLY 1 FP-023 flexible board (CN101) 2 Flexible board (CN183) 3 Screw (1.7 × 4) 4 Lens block assembly 2-7. SY-58 BOARD, DD-141 BOARD AND JK-194 BOARD 7 Three connectors (CN701, 702, 713) 6 Flexible board (CN708) 5 SY-58 board 8 Screw (M1.7 ) 2 FP-025 flexible board (CN703) 4 Two screws qd Open the JK lid. (1.7 × 4) qf JK-194 board qs Screw qa DD-141 board (1.7 × 4) 3 Screw (1.7 × 4) 1 FP-026 flexible 9 Screw board (CN201) 0 Connector (M1.7) (CN711) Note: Do not remove these two screws. – 9 –, 2-8. CONTROL SWITCH BLOCK AND SW-339 BOARD 3 Control switch block (Zoom/power SW) 1 Two screws (1.7 × 4) 2 Screw (1.7 × 4) 4 Two screws Note: In mounting the SW-339 board, (1.7 × 4) align the SW knob (S109) with the slide knob holder. 5 Screw (1.7 × 4) 6 SW-339 board Slide knob holder S109 2-9. HINGE ASSEMBLY AND KJ-11 BOARD 0 Remove the hinge assembly after turning it toward arrow6Pcabinet (Front) A direction. A 7 Two screws (M1.7) 8 BL fixed plate 4 Screw 9 Three screws (M1.7) (M1.7) 5 Hinge cover (B) qs KJ-11 board qa KJ clip 1 Screw (M1.7) 3 Hinge cover (T) 2 Claw – 10 –,

DSC-S30/S50

3. REPAIR PARTS LIST 3-1. EXPLODED VIEWS NOTE: • -XX and -X mean standardized parts, so they may • Items marked “*” are not stocked since they are The components identified by mark have some difference from the original one. seldom required for routine service. Some delay 0 or dotted line with mark 0 are • Color Indication of Appearance Parts should be anticipated when ordering these items. critical for safety. Example: • The mechanical parts with no reference number in Replace only with part number speci- KNOB, BALANCE (WHITE) .(RED) the exploded views are not supplied. fied. ↑ ↑ Parts Color Cabinet's Color 3-1-1. FRONT PANEL SECTION not 10 supplied 11 12 4 Main section 8 not (See page 12) supplied not 4 supplied6914 BZ901 not 15 13 supplied 5 (S50) 4 18 SP901 3 13 19 17 not supplied 2 MIC901 4 13 16 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3950-656-1 CABINET (FRONT) ASSY (S50) 10 X-3950-665-1 CABINET (UPPER) ASSY (S30) 1 X-3950-664-1 CABINET (FRONT) ASSY (S30) 11 3-060-275-01 KNOB, MODE 2 3-061-075-01 LABEL, LENS 12 3-061-115-01 BRACKET, STRAP 3 3-061-675-01 RING, ORNAMENTAL 13 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 4 3-968-729-91 SCREW (M2), LOCK ACE, P2 14 1-476-038-11 SWITCH BLOCK, CONTROL (MODE SW) 5 3-060-251-01 LID, CPC 015 not supplied FLASH UNIT 6 3-050-594-01 SPRING, COMPRESSION 16 3-061-114-01 HOLDER, MISP (S50) 7 3-061-076-01 LID, BATTERY (S50) * 17 3-055-971-01 CUSHION, MICROPHONE (S50) 7 3-061-076-11 LID, BATTERY (S30) * 18 3-061-077-01 PLATE (1), GROUND 8 3-060-284-11 SLIDER, BT LOCK (S50) 19 3-060-274-01 SCREW, TRIPOD 8 3-060-284-21 SLIDER, BT LOCK (S30) BZ901 1-529-739-11 BUZZER, PIEZOELECTRIC (S30) 9 3-318-382-01 SCREW (1.7X3), TAPPING MIC901 1-542-428-11 MICROPHONE UNIT (S50) 10 X-3950-659-1 CABINET (UPPER) ASSY (S50) SP901 1-505-862-41 SPEAKER (2.0 cm) (S50) – 11 –, 3-1-2. MAIN SECTION 59 Rear cabinet section (See page 13)

A

52 70 52 BT901 58 52 57 55

A

55 52 64 52 52 56 65 not supplied 68 Lens block assembly 66 (See page 14) not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number speci- fied. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3950-655-1 HOLDER ASSY, BT 060 1-794-045-11 CONNECTOR, DC-IN 52 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 61 1-678-002-11 FP-025 FLEXIBLE BOARD 53 not supplied MS-50 BOARD, COMPLETE 62 3-061-157-11 BUTTON, FUNCTION 54 3-969-380-01 SPRING, BATTERY 63 not supplied SW-339 BOARD, COMPLETE 55 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 64 1-678-003-11 FP-026 FLEXIBLE BOARD 56 not supplied DD-141 BOARD, COMPLETE (S50) 65 not supplied JK-194 BOARD, COMPLETE 56 not supplied DD-141 BOARD, COMPLETE (S30) * 66 3-061-069-01 FRAME, JK 57 1-677-877-11 FP-024 FLEXIBLE BOARD * 67 3-060-250-01 FRAME, SD 58 not supplied SY-58 BOARD, COMPLETE (SERVICE) (S50) 68 1-960-457-11 HARNESS (YP-052) 58 not supplied SY-58 BOARD, COMPLETE (SERVICE) (S30) * 69 3-062-774-01 SHEET (SH) 59 1-476-039-11 SWITCH BLOCK, CONTROL * 70 3-061-699-01 SY SHEET (260) (ZOOM/POWER SW) BT901 1-694-654-11 TERMINAL BOARD, BATTERY – 12 –,

Ver 1.3 2004. 07

3-1-3. REAR CABINET SECTION LCD901 ND901 112 117 111 113 113 115 119 A 118 110 115 133 109 110 108 122 107 108 123 106 124

A

126 125 104 135 103 129 not supplied 102 134 108 128 The components identified by mark 101 0 or dotted line with mark 0 arecritical for safety. Replace only with part number speci- fied. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 3-061-079-01 COVER (T), HINGE 119 not supplied PD-127 BOARD, COMPLETE (S30) * 102 3-061-083-01 CLIP, KJ 120 1-960-472-11 HARNESS (YP-053) 103 not supplied KJ-11 BOARD, COMPLETE 121 1-960-473-11 HARNESS (YP-054) 104 1-960-474-11 HARNESS (SK-100) 122 3-060-299-12 KNOB, POWER * 105 3-061-082-01 HOLDER, KJ 123 3-318-382-02 SCREW (1.7), TAPPING 106 X-3950-657-1 HINGE ASSY 124 3-061-108-01 HOLDER, LOCK 107 3-061-084-01 COVER (B), HINGE 125 3-061-107-01 LEVER, LOCK 108 3-061-216-01 ACE (M1.7), SPECIAL HEAD LOCK 126 3-061-109-01 SPRING, LOCK 109 X-3950-658-1 CABINET (REAR) ASSY (S50) 127 3-959-978-02 CUSHION, PANEL 109 X-3950-794-1 CABINET (REAR) ASSY (S30) 128 3-061-096-01 LID, JK 110 3-968-729-91 SCREW (M2), LOCK ACE, P2 129 3-051-520-01 SPRING, POWER 111 3-061-080-01 CABINET (REAR), P 130 3-060-297-01 HOLDER, POWER 0112 not supplied TRANSFORMER UNIT, INVERTER 131 3-061-111-01 COVER, DC * 113 3-051-232-01 CLIP, PCB * 132 3-062-825-01 SHEET, KJ 114 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION * 133 3-062-736-01 SHEET, ELECTROSTATIC 115 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 134 3-061-113-01 HOLDER, SLIDE KNOB 116 3-973-497-91 SCREW (M1.7), 0-NO. +P 2 135 3-061-112-01 KNOB, SLIDE 117 3-061-078-01 CABINET (FRONT), P 136 3-060-295-01 SHEET (BL) * 118 3-061-081-01 PLATE, BL FIXED LCD901 not supplied INDICATOR MODULE LIQUID CRYSTAL 119 not supplied PD-127 BOARD, COMPLETE (S50) 0ND901 not supplied TUBE, FLUORESCENT, COLD CATHODE – 13 –, 3-1-4. LENS BLOCK ASSEMBLY 155 156 154 156 IC301 161 160 M901 M902 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 not supplied LENS, ZOOM (VCL-6103WA) 160 not supplied RUBBER (CL), SEAL 154 3-061-122-01 SHEET, LENS 161 not supplied FILTER BLOCK, OPTICAL (S30) 155 3-061-121-01 FRAME (260), LENS 161 not supplied FILTER BLOCK, OPTICAL (S50) 156 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 162 not supplied ADAPTOR (CL), CCD FITTING 157 1-678-001-11 FP-023 FLEXIBLE BOARD IC301 not supplied CCD BLOCK ASSY (CCD IMAGER) (S30) 158 3-947-268-11 TITE (2), +B TAPPING (P) IC301 not supplied CCD BLOCK ASSY (CCD IMAGER) (S50) 159 not supplied CD-262 BOARD, COMPLETE (S50) M901 3-709-573-01 MOTOR UNIT, FOCUS 159 not supplied CD-262 BOARD, COMPLETE (S30) M902 3-709-574-01 MOTOR UNIT, ZOOM – 14 –,

DSC-S30/S50

4. GENERAL This section is extracted from DSC-S30/S50 instruction manual. CAUTION Note: Caution:

WARNING You are cautioned that any changes or This equipment has been tested and found to Do not handle damaged or leaking lithium

modifications not expressly approved in this To prevent fire or shock hazard, do comply with the limits for a Class B digital ion battery. manual could void your authority to operate device, pursuant to Part 15 of the FCC not expose the unit to rain or this equipment. Rules. These limits are designed to provide moisture. reasonable protection against harmful For the Customers in Canada

Declaration of Conformity interference in a residential installation. This

equipment generates, uses, and can radiate CAUTION

For the Customers in the Trade Name: SONY radio frequency energy and, if not installed TO PREVENT ELECTRIC SHOCK, DO U.S.A. Model No.: DSC-S30 and used in accordance with the NOT USE THIS POLARIZED AC PLUG

Responsible Party:Sony Electronics Inc. instructions, may cause harmful interference WITH AN EXTENSION CORD, Address: 1 Sony Drive, Park to radio communications. However, there is RECEPTACLE OR OTHER OUTLET Ridge, NJ 07656 no guarantee that interference will not occur UNLESS THE BLADES CAN BE FULLY USA in a particular installation. If this equipment INSERTED TO PREVENT BLADE Telephone No.: 201-930-6972 does cause harmful interference to radio or EXPOSURE. television reception, which can be This device complies with Part 15 of the determined by turning the equipment off and FCC Rules. Operation is subject to the on, the user is encouraged to try to correct NOTICE FOR THE following two conditions: (1) This the interference by one or more of the CUSTOMERS IN THE UNITED device may not cause harmful following measures: KINGDOM interference, and (2) this device must — Reorient or relocate the receiving accept any interference received, antenna. A moulded plug complying with BS 1363 is including interference that may cause — Increase the separation between the fitted to this equipment for your safety and undesired operation. equipment and receiver. convenience. This symbol is intended to alert the user to the presence — Connect the equipment into an outlet of uninsulated “dangerous on a circuit different from that to which Should the fuse in the plug supplied need to

Declaration of Conformity the receiver is connected. be replaced, a 5 AMP fuse approved by voltage” within the

product’s enclosure that Trade Name: SONY — Consult the dealer or an experienced ASTA or BSI to BS 1362, (i.e. marked with or mark) must be used. may be of sufficient Model No.: DSC-S50 radio/TV technician for help. magnitude to constitute a Responsible Party:Sony Electronics Inc. The shielded interface cable recommended Address: 1 Sony Drive, Park in this manual must be used with this If the plug supplied with this equipment has risk of electric shock to a detachable fuse cover, be sure to attach the persons. Ridge, NJ 07656 equipment in order to comply with the limits USA for a digital device pursuant to Subpart B of fuse cover after you change the fuse. Never This symbol is intended to Telephone No.: 201-930-6972 Part 15 of FCC Rules. use the plug without the fuse cover. If you should lose the fuse cover, please contact alert the user to the presence This device complies with Part 15 of the DISPOSAL OF LITHIUM ION your nearest Sony service station. of important operating and maintenance (servicing) FCC Rules. Operation is subject to the BATTERY. instructions in the literature following two conditions: (1) This For the Customers in accompanying the device may not cause harmful LITHIUM ION BATTERY. appliance. interference, and (2) this device must DISPOSE OF PROPERLY. Germany accept any interference received, Never expose the battery pack to You can return your unwanted lithium ion Directive:EMC Directive 89/336/EEC.92/including interference that may cause temperature above 140˚F (60˚C), such as in batteries to your nearest Sony Service 31/EEC undesired operation. a car parked in the sun or under direct Center or Factory Service Center. This equipment complies with the EMC sunlight. regulations when used under the following Note: circumstances: In some areas the disposal of lithium ion If you have any questions about this • Residential area batteries in household or business trash may product, you may call: • Business district be prohibited. Sony Customer Information Center • Light-industry district 1-800-222-SONY (7669) (This equipment complies with the EMC For the Sony Service Center nearest you call or write to: standard regulations EN55022 Class B.) 1-800-222-SONY (United States only) Sony Customer Information Center For the Sony Factory Service Center nearest 1 Sony Drive, Mail Drop #T1-11, Park you call 416-499-SONY (Canada only) Ridge, NJ 0765623Getting started

Attention Notes on image data compatibility • This camera conforms with the Design Identifying the parts

The electromagnetic fields at the specific Rules for Camera File Systems universal frequencies may influence the picture and standard established by the JEIDA (Japan sound of this camera. Electronic Industries Development See the pages in parentheses for details of operation. Association). You cannot play back on your camera still images recorded on other15“Memory Stick” equipment (DCR-TRV890/TRV900/ 6 TRV900E, DSC-D700, DSC-D770) that 2 does not conform with this universal 7 standard. (These models are not sold in38some areas.)

N50 • Playback of images recorded with your camera on other equipment and playback

of images recorded or edited with other equipment on your camera are not guaranteed. 9

For the Customers in CANADA

Precaution on copyright This Class B digital apparatus complies with Television programs, films, video tapes, and Canadian ICES-003. 0 qaother materials may be copyrighted. Unauthorized recording of such materials

For the Customers in the may be contrary to the provision of the U.S.A. copyright laws. 4 qs

This device complies with Part 15 of the Do not shake or strike the camera FCC Rules. Operation is subject to the In addition to malfunctions and inability to following two conditions: (1) This device A Flash (19) I Lens record images, this may render the may not cause harmful interference, and “Memory Stick” unusable or image data B MODE selector (29) J A/V OUT jack (DSC-S50 only) (2) this device must accept any interference breakdown, damage or loss may occur. (48) received, including interference that may C Shutter button (16) (20) cause undesired operation. LCD screen and lens Audio output is monaural. • The LCD screen is manufactured using D Lens cap VIDEO OUT jack (DSC-S30 high-precision technology. However, there only) (48)

Be sure to read the following may be some tiny black points and/or E Photocell window for flash

before using your camera bright points (red, blue or green in color) Do not block while recording. K USB jack (25) (26) that constantly appear on the LCD screen. • This Owner's Manual is for the two These points are normal in the F Self-timer/recording lamp L Tripod receptacle (bottom models of the DSC-S30 and the manufacturing process and do not affect surface) DSC-S50. Check to make sure which the recording in any way. Over 99.99% of G Built-in microphone (DSC-S50 Use a tripod with a screw length of model you have purchased before the pixels are operational for effective use. only) less than 9/32 inch (6.5 mm). You you use your camera. • Be careful when placing the camera near a Do not touch while recording. • The illustrations in this manual will be unable to firmly secure the window or outdoors. Exposing the LCD show the DSC-S50. screen or the lens to direct sunlight for H Speaker (DSC-S50 only) camera to tripods having longer long periods may cause malfunctions. screws, and may damage the Trial recording camera. Before you record one-time events, you may Do not get the camera wet want to make a trial recording to make sure When taking pictures outdoors in the rain or that the camera is working correctly. under similar conditions, be careful not to get the camera wet. If moisture No compensation for contents of condensation occurs, refer to page 54 and the recording follow the instructions on how to remove it Contents of the recording cannot be before using the camera. compensated for if recording or playback is not possible due to a malfunction of your Back up recommendation camera, etc. To avoid the potential risk of data loss, always copy (back up) data to a disk. 4 6 – 15 –, Preparing the power supply Attaching the strap

Installing the battery pack

Your camera operates only with the “InfoLITHIUM” NP-FM50 battery pack* (M series). You cannot use any other battery pack. 290qa qf 5 qs qg 6 qd 7 qh 8 qj Battery eject lever A Flash button G DISPLAY button B FOCUS button (41) H LCD screen 1 Open the battery/“Memory Stick” cover. C LCD BACKLIGHT BRIGHT/ I Hook for lens cap/strap Open the cover while sliding the OPEN switch in the direction of the arrow. NORMAL switch J Zoom button Install the battery pack. Usually set to NORMAL. When 2 Insert the battery pack with the B mark facing tow ard the battery compartment you use the camera outdoors or in K Access lamp (15) as illustrated. other bright places, setting this to BRIGHT makes the LCD screen L Battery/“Memory Stick” cover 3 Close the battery/“Memory Stick” cover.bright and easy to see, but also M Battery eject lever (8) uses up the battery faster. N OPEN switch D Control button To remove the battery pack O POWER switch E PROGRAM AE +/– button Open the battery/“Memory Stick” cover. Slide the battery eject lever VOLUME +/– button P DC IN jack (9) (12) downward, and remove the battery pack. Be careful not to drop the battery pack when removing it. F PROGRAM AE button (42) Q POWER lamp/BATT CHARGE lamp (9) (13) * What is “InfoLITHIUM”? “InfoLITHIUM” is a lithium ion battery pack which can exchange information such as battery consumption with compatible video equipment. This unit is compatible with the “InfoLITHIUM” battery pack (M series). “InfoLITHIUM” M series battery packs have the mark. “InfoLITHIUM” is a trademark of Sony Corporation. 7 8

Charging the battery pack Charging time

You cannot charge the battery pack while your camera is turned on. Be sure to turn Battery pack Full charge (min.) Normal charge (min.) off your camera before charging. NP-FM50 (supplied) 150 90 Approximate time to charge a completely discharged battery pack using the A BATT CHARGE lamp AC power adaptor. Battery pack (M series) To the wall outlet (mains) Battery life and number of images that can be recorded/played back STILL mode recording* Power cord DC IN jack cover (mains lead) DSC-S50 LCD BACKLIGHT Battery life (min.) Number of images BRIGHT 140 (130) 2300 (2100) NORMAL 150 (140) 2500 (2300) AC-L10 DSC-S30 AC power adaptor LCD BACKLIGHT Battery life (min.) Number of images BRIGHT 140 (130) 2800 (2600) 1 Insert the battery pack into your camera. NORMAL 150 (140) 3000 (2800) STILL mode playback** (DSC-S50/S30) 2 Open the DC IN jack cover and connect the DC connecting cable to the DC IN jack of your camera with the v mark facing up. LCD BACKLIGHT BaCtte-Lry1 0li fe (min.) Number of images BRIGHT 170 (160) 3400 (3200) 3 Connect the power cord (mains lead) to the AC power adaptor and then to a wall outlet (mains). NORMAL 220 (210) 4400 (4200) The BATT CHARGE lamp lights orange when charging begins. When the Approximate battery life and number of images that can be recorded/played back BATT CHARGE lamp goes off, normal charge is completed. For full with a fully charged battery pack at a temperature of 77˚F (25˚C), 640×480 image charge, which allows you to use the battery longer than usual, leave the size and in NORMAL recording mode. Numbers in parentheses indicate the time battery pack inserted for about one hour after normal charge is completed. when you use a normally charged battery pack. ∗ Recording at about 5-second intervals Battery remaining indicator ∗∗ Playing back single images in order at about 3-second intervals The LCD screen on the camera shows the remaining time for which you can still record or play back images. MOVIE mode recording (DSC-S50 only) This indication may not be entirely accurate depending on the conditions of use and LCD BACKLIGHT Battery life (min.) the operating environment. BRIGHT 140 (130) Auto power-off function NORMAL 150 (140) If you do not operate the camera for about three minutes during recording, the camera turns off automatically to prevent wearing down the battery. To use the Approximate time that can be recorded with a fully charged battery pack at a camera again, slide down the POWER switch to turn on the camera again. temperature of 77˚F (25˚C) and 160×112 image size. Numbers in parentheses indicate the time when you use a normally charged battery pack. 9 10 – 16 –

Getting started Getting started

, Notes • The battery life and number of images will be decreased if you use your camera at low Using the AC power adaptor temperatures, use the flash, repeatedly turn the power on/off or use the zoom. • The capacity of the “Memory Stick” is limited. The above figures are a guide when you continuously record/play back while replacing the “Memory Stick.” • If sufficient battery remaining time is indicated but the power runs out soon, fully charge the battery so that the correct battery remaining time appears. • Do not short the DC plug of the AC power adaptor with a metallic object, as this may cause To the wall outlet (mains) malfunction. • Do not expose the battery pack to water. DC IN jack cover Power cord (mains lead) AC-L10 AC power adaptor 1 Open the DC IN jack cover and connect the DC connecting cable to the DC IN jack of your camera with the v mark facing up. 2 Connect the power cord (mains lead) to the AC power adaptor and then to a wall outlet (mains). Using a car battery Use Sony DC adaptor/charger. 11 12

Setting the date and time 5 Select the desired date display format with

v/V on the control button, then press the When you first use your camera, set the date and time. If these are not set, the center z. CLOCK SET screen appears whenever you turn on your camera for recording. Select from Y/M/D (year/month/day), M/D/Y (month/day/year) or D/M/Y (day/month/year). 6 Select the year, month, day, hour or minute Control button item you want to set with b/B on the control button. The item to be set is indicated with v/V.

POWER

lamp 7 Set the numeric value with v/V on the control button, then press the center z to enter it. After entering the number, v/V moves to the next item. If you selected [D/M/Y] in step 5, set the time on a 24-hour cycle. 1 Slide down the POWER switch to turn on the power. 8 Select [ENTER] with B on the control The POWER lamp lights up. button, then press the center z at the desired moment to begin clock movement. 2 Press v on the control button. The date and time are entered. The menu bar appears on the LCD screen. To cancel the date and time setting Select [CANCEL] with v/V/b/B on the control button, then press the center z. 3 Select [SETUP] with B on the control button, then press the center z. 4 Select [CLOCK SET] with v/V on the control button, then press the center z. 13 14 – 17 –

Getting started Getting started

,

Basic operations B Recording Inserting the “Memory Stick” Recording still images

Still images are recorded in JPEG format. To record still images, slide the POWER switch down to turn on the power and insert a “Memory Stick.” Access lamp POWER switch 1 Open the battery/“Memory Stick” cover. Open the cover while sliding the OPEN switch in the direction of the arrow. 2 Insert the “Memory Stick.” Set the MODE selector to STILL. Insert the “Memory Stick” with the B mark facing toward the battery 1 compartment as illustrated until it clicks. 2 Press and hold the shutter button halfway Remaining memory 3 Close the battery/“Memory Stick” cover. down and check the image. utton. capacity indicatorWhile the AE lock indicator z (green) is flashing, the image freezes momentarily, but is not yet ention switch is set to Removing the “Memory Stick” recorded. When the camera finishes the automatic adjustments*, the AE lock indicator z lights up Open the battery/“Memory Stick” cover, then press the “Memory Stick” once lightly. and the camera is ready for recording. Notes To cancel the recording, release the shutter b • Insert the “Memory Stick” firmly until it clicks, otherwise a message such as “MEMORY STICK ERROR” will be displayed. AE lock indicator • Never remove the “Memory Stick” or turn off the power while the access lamp is lit up. • You cannot record or edit images on a “Memory Stick” if the erasure prev the LOCK position. 3 Press the shutter button fully down. Connector The shutter sounds and the image is recorded on the “Memory Stick.” When “REC” disappears, you can record the next image. Erasure prevention switch LOCK ∗ Exposure and focus are automatically adjusted. The number of images you can record on a “Memory Stick” See pages 37 to 40. Note While the image is being recorded on the “Memory Stick,” do not shake or strike the camera. Label space Also, do not turn the power off, or remove the battery pack or “Memory Stick.” 15 16 Checking the last recorded image (Quick Review) LCD screen indicators during recording You can check the last recorded image by clearing the menu bar from the screen Press DISPLAY to turn on/off the indicators on the LCD screen. (page 31) and pressing b on the control button. To return to the normal recording See page 64 for a detailed description of the indicated items. mode, press lightly on the shutter button or select [RETURN] with b/B on the control button and then press the center z. You can also delete the image first by selecting [DELETE] on the Quick Review screen with b/B on the control button and pressing the center z, and then selecting [OK] with v/V on the control button and pressing the center z.

DISPLAY

Using the zoom feature Zoom button Notes W side: for wide-angle (subject appears • You cannot turn off the self-timer indicators and some of the indicators used in advanced farther away) operations. • The indicators on the LCD screen are not recorded.

Using the self-timer

T side: for telephoto (subject appears closer) When you use the self-timer function, the subject is recorded about 10 seconds after you press the shutter button. Minimum focal distance to the subject Shutter button W side: About 9 7/8 inches (25 cm) or more T side: About 23 5/8 inches (60 cm) or more Self-timer lamp To record even closer subjects, see page 41. Digital zoom function Control button This camera has a digital zoom function. Digital zoom enlarges the image by digital processing and it starts to function when zoom exceeds 3×. Select (self-timer) indicator on the LCD screen with v/V/b/B on the control button, then press the center z. The (self-timer) indicator appears on the LCD screen, and about 10 seconds after you press the shutter button, the subject is The T side of the bar shows the recorded. The self-timer lamp flashes after you press the shutter button until the digital zooming zone. shutter is released. Using digital zoom • The maximum zoom magnification is 6×. • Digital zooming deteriorates the picture quality. When digital zoom is not necessary, set [DIGITAL ZOOM] to [OFF] in the menu settings (page 34). Note Digital zoom does not work for moving images. 17 18 – 18 –

Getting started B Recording

,

Recording images with the flash Recording moving images (DSC-S50 only)

The initial setting is auto (no indicator). In this mode, the flash automatically strobes Moving images with audio are recorded in MPEG format. when the surroundings become dark. When you change the flash mode, press the To record moving images, slide the POWER switch down to turn on the power and (flash) repeatedly so that the flash mode indicator appears on the LCD screen. insert a “Memory Stick.” (flash)

DISPLAY

POWER switch Each time you press the (flash), the indicator changes as follows. (No indicator) tttt(No indicator) Auto red-eye reduction: The flash strobes before recording to reduce the red-eye phenomenon. Forced flash: The flash strobes regardless of the surrounding brightness. 1 Set the MODE selector to MOVIE. No flash: The flash does not strobe. You can change the brightness of the flash (FLASH LEVEL) in the menu settings 2 Press the shutter button fully down. (page 34). “REC” appears on the LCD screen, and the image and sound are recorded on Notes the “Memory Stick.” • The recommended shooting distance using the built-in flash is 31/32 feet to 8 1/3 feet (0.3 m to If you press the shutter button momentarily 2.5 m). The image and sound are recorded for five seconds. You can change the • Attaching a conversion lens (not supplied) may block the light from the flash or cause the lens recording time to 10 or 15 seconds with [REC TIME SET] in the menu settings shadow to appear. • Auto red-eye reduction may not produce the desired red-eye reduction effects depending on (page 33). individual differences, the distance to the subject, if the subject does not see the pre-strobe, or If you hold the shutter button down other conditions. In addition, red-eye reduction effects are also difficult to obtain if you set the The image and sound are recorded while the shutter button is held down for up shutter to a slow speed in the PROGRAM AE shutter priority mode. • The flash effect is not obtained easily when you use forced flash in a bright location. to 60 seconds. However, when [IMAGE SIZE] in the menu setting is set to [320×240], the maximum recording time is 15 seconds (page 33). Zooming or using the self-timer, etc. See pages 17 and 18. LCD screen indicators during recording Press DISPLAY to turn on/off the indicators on the LCD screen. These indicators are not recorded. See page 64 for a detailed description of the indicators. 19 20 B Playback

Playing back still images Playing back moving images

VOLUME +/– POWER switch POWER switchDISPLAY DISPLAY 1 Set the MODE selector to PLAY. 1 Set the MODE selector to PLAY. The last recorded image (still or moving) appears on the LCD screen. The last recorded image (still or moving) appears on the LCD screen. 2 Press v on the control button to display the menu bar on the LCD 2 Press v on the control button to display the menu bar on the LCD screen. screen. 3 Select the desired moving image with the 3 Select the desired still image with the control button. control button. Moving images are displayed one-size smaller than Press v/V/b/B on the control button to select "b/B" still images. on the LCD screen, then press b/B on the control Press v/V/b/B on the control button to select "b/B" button. on the LCD screen, then press b/B on the control "b: To display the preceding image. button. B": To display the next image. "b: To display the preceding image. B": To display the next image. 4 Select B (playback) on the LCD screen with B (playback)/X When the menu bar is not displayed v/V/b/B on the control button, then press You can directly select and play back the image with b/B on the control button. the center z. The moving image and sound* are played back. Notes During playback, B (playback) changes to X • You might not be able to correctly play back images recorded with this camera on other (pause). equipment. ∗ You can play back sound in DSC-S50 only. • You cannot play back on this camera images larger than the maximum image size that can be recorded with this camera. Playback bar

LCD screen indicators during still image playback

Press DISPLAY to turn on/off the indicators on the LCD screen. To pause playback See page 64 for a detailed description of the indicators. Select X (pause) on the LCD screen with v/V/b/B on the control button, then press the center z. 21 22 – 19 –

B Recording B Playback

, When the menu bar is not displayed Viewing images using a personal computer You can directly select the image with b/B on the control button, and play back the image and sound (DSC-S50 only) by pressing the center z. When you press the You can view data recorded with your camera on a personal computer and attach it to center z during playback, playback is paused. e-mail. This section describes the method for installing the USB driver and viewing images on a personal computer. Be sure to also see the operation manuals for your

Adjusting the volume (DSC-S50 only) personal computer and application software.

Press VOLUME +/– to adjust the volume. Note Data recorded with your camera is stored in the following formats. Make sure that applications that support these file formats are installed on your personal computer.

LCD screen indicators during moving image playback • Still images (other than TEXT and uncompressed modes): JPEG format

• Moving images/audio: MPEG format Press DISPLAY to turn on/off the indicators on the LCD screen. • Uncompressed mode still images: TIFF format See page 64 for a detailed description of the indicators. • TEXT mode: GIF format

Recommended computer environment

Recommended Windows environment OS: Microsoft Windows 98, Windows 98SE Standard installation is required. Operation is not assured in an environment upgraded from: Windows 3.1, Windows 95 to Windows 98 or Windows 98 to Windows 98SE. CPU: MMX Pentium 200 MHz or faster The USB connector must be provided as standard. ActiveMovie Player (DirectShow) must be installed (to play back moving pictures). Recommended Macintosh environment Macintosh computer with the Mac OS 8.5.1/8.6/9.0 standard installation However, note that the update to Mac OS 9.0 should be used for the following models. • iMac with the Mac OS 8.6 standard installation and a slot loading type CD-ROM drive • iBook or G4 with the Mac OS 8.6 standard installation The USB connector must be provided as standard. QuickTime 3.2 or newer must be installed (to play back moving pictures). Notes • Operations are not guaranteed for either the Windows or Macintosh environment if you connect two or more USB equipment to a single personal computer at the same time (except for the USB keyboard and mouse which are provided as standard), or when using a hub. • Depending on the type of USB equipment that is used simultaneously, some equipment may not operate. • Operations are not guaranteed for all the recommended computer environments mentioned above. 23 24

Installing the USB driver 3 Double-click the CD-ROM drive icon to open the window.

Before connecting your camera to your personal computer, install the USB driver to the computer. The USB driver is contained together with application software for 4 Double-click the icon of the hard disk containing the OS to open viewing images on a CD-ROM which is supplied with your camera. the window. For Windows 98 users 5 Move the following two driver files from the window opened in step 3 to the “System Folder” icon in the window opened in step41Turn on your personal computer and allow Windows 98 to load. (drag and drop). • Sony USB Driver • Sony USB Shim 2 Insert the supplied CD-ROM in the CD-ROM drive of your personal computer. 6 When “Put these items into the Extensions folder?” appears, click “OK.” 3 Connect the USB jack on your camera with the USB connector on your personal computer using the supplied USB cable. 7 Restart your personal computer. to the USB connector to the USB jack Viewing images For Windows 98 users Push in until the USB cable connector clicks 1 Turn on the power of your personal computer and allow Personal computer into place Windows 98 to load. 2 Connect one end of the USB cable to the USB jack on the camera 4 Insert a “Memory Stick” into your camera, connect the AC power and the other end to the USB connector on your personal adaptor and turn on your camera. computer. “PC MODE” appears on the LCD screen of your camera and the camera is set to communication standby mode. Your personal computer recognizes the camera, and the Windows 98 Add Hardware Wizard starts. to the USB connector to the USB jack 5 Follow the on-screen messages to specify the CD-ROM drive and install the USB driver. The Add Hardware Wizard starts twice because two different USB drivers are Push in until the installed. Be sure to allow the installation to complete without interrupting it. USB cable connector clicks Personal computer into place Note 3 Insert a “Memory Stick” into your camera, and connect the AC Be sure to insert a “Memory Stick” into your camera before installing the USB driver. power adaptor to your camera and then to a wall outlet (mains). Otherwise, you will be unable to install the USB driver. 4 Turn on the power of your camera. For Macintosh users “PC MODE” appears on the LCD screen of the camera. 1 Turn on your personal computer and allow the Mac OS to load. 5 Open “My Computer” on Windows 98 and double click the newly recognized drive. (Example: “Removable Disk (D:)”) 2 Insert the supplied CD-ROM in the CD-ROM drive of your personal The folders inside the “Memory Stick” are displayed. computer. 25 26 – 20 –

B Playback B Playback

, 6 Select and double-click the desired image/sound file from the Image file storage destinations and image folder. For the detailed folder and file name, see “Image file storage destinations and files image files” (page 28). Image files recorded with your camera are grouped in folders by recording mode. Desired file type Double-click in this order The meanings of the file names are as follows. ssss stands for any number Still image “Dcim” folder “100msdcf” folder Image file within the range from 0001 to 9999.t t Moving image* “Mssony” folder t “Moml0001” folder t Image file* For Windows 98 users (The drive recognizing the camera is “D.”) Audio* “Mssony” folder t “Momlv100” folder t Audio file* E-mail image “Mssony” folder t “Imcif100” folder t Image file TIFF image (uncompressed) Folder containing still image data ∗ Copying a file to the hard disk of your personal computer before viewing it is Folder containing E-MAIL mode and TIFF recommended. If you play back the file directly from the “Memory Stick”, the image mode image data and sound may break off. Folder containing moving image data Folder containing VOICE mode audio data

Notes on using your personal computer

“Memory Stick” Folder File Meaning • “Memory Stick” operations on your camera cannot be assured if the “Memory Stick” has been 100msdcf DSC0ssss.JPG • Still image file recorded normally formatted on your personal computer. • Still image file recorded in E-MAIL • Do not optimize the “Memory Stick” on a Windows machine. This will shorten the “Memory Stick” life. mode (page 38) • Do not compress the data on the “Memory Stick.” Compressed files cannot be played back on • Still image file recorded in TIFF mode your camera. (page 40) • Still image file recorded in VOICE Software mode (page 39) • Depending on your application software, the file size may increase when you open a still image TXT0ssss.GIF • Still image file recorded in TEXT mode file. (page 39) • When you load an image modified using the supplied retouch software from your personal computer to the camera or when you directly modify the image on the camera, the image Imcif100 DSC0ssss.JPG • Small-size image file recorded in E- format will differ so the “FILE ERROR” message may appear and you may be unable to open MAIL mode (page 38) the file. DSC0ssss.TIF • Uncompressed image file recorded in TIFF mode (page 40) Communications with your personal computer Communications between your camera and your personal computer may not recover after Moml0001 MOV0ssss.MPG • Moving image file recorded normally recovering from Suspend, Resume, or Sleep. Momlv100 DSC0ssss.MPG • Audio file recorded in VOICE mode (page 39) • Windows and ActiveMovie, DirectShow are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. The numerical portions of the following files are the same. • Macintosh and Mac OS, QuickTime are trademarks of Apple Computer, Inc. — A small-size image file recorded in E-MAIL mode and its corresponding image file • All other product names mentioned herein may be the trademarks or registered trademarks of — An uncompressed image file recorded in TIFF mode and its corresponding image file their respective companies. Furthermore, “™” and “®” are not mentioned in each case in this — An audio file recorded in VOICE mode and its corresponding image file manual. 27 28

Advanced operations

Turning on/off the operation buttons (menu bar) on the LCD screen

Before performing advanced operations

Press v to display the menu bar This section describes the basic control methods that are frequently used for on the LCD screen. “Advanced operations”.

How to use the MODE selector

Press V to clear the menu bar The MODE selector selects whether you can use your camera to record or to play from the LCD screen. Menu bar back and edit images. Set the selector as follows before starting to operate your camera. Note PPLLAAYY PPLLAAYY You cannot clear the menu bar during INDEX screen display (page 45). SSTTIILLLL SSTTIILLLL

MMOOVVIIEE

Selecting items and images on the LCD screen DSC-S50 DSC-S30 PLAY: To play back or edit images 1 Press v/V/b/B on the STILL: To record still images control button to select the and voice memos item you want to set or the MOVIE: To record moving image you want to display. images The color of the selected item or (DSC-S50 only) the border of the selected image changes from blue to yellow.

How to use the control button 2 Press the center z to enter the item.

Repeat steps 1 and 2 to execute The control button is used to select the indicators, images and menus appearing on each function. the LCD screen of your camera. The operation methods that are frequently used for “Advanced operations” are described below. Select Enter (OK) The “Advanced operations” section of this manual refers to selecting and entering items by the above procedure as “Select [(item name)].” 29 30 – 21 –

Before performing advanced operations B Playback

,

How to change the menu settings Menu settings

Some of the advanced operations for your camera are executed by selecting menu Menu items that can be modified differ depending on the setting of the MODE items displayed on the LCD screen with the control button. selector. The LCD screen shows only the items you can operate at the moment. Initial settings are indicated with x. MODE selector (SELF TIMER) Records with the self-timer (page 18).

EFFECT

Item Setting Description MODE selector P.EFFECT SOLARIZE Sets the image special effects (page 44). MOVIE B&W STILL

SEPIA

1 Press v on the control button to display the menu bar. NEG.ART The menu bar appears as follows according to the setting of the MODE xOFF selector. DATE/ DAY&TIME Sets whether to insert the date and time STILL TIME DATE into the image (page 44). MOVIE/STILL PLAY (single mode) PLAY (INDEX mode) xOFF

FILE

Item Setting Description MODE selector FORMAT OK Formats a “Memory Stick.” MOVIE 2 Select the desired item with v/V/b/B on the CANCEL Cancels formatting of a “Memory

STILL

control button, then press the center z. Stick.” PLAY The color of the selected item changes from blue to POS. ON Plays back images recorded with the STILL yellow, and when you press the center z, the modes SENSOR camera on its side (vertical images) as that can be set for that item are displayed. horizontal images. This function does not work for images recorded in TEXT mode. 3 Select the desired mode with v/V/b/B on the control button, then press the center z. xOFF When this camera may be subject to vibration such as when you record images from inside a moving car, set this to OFF to prevent improper To clear the menu horizontal/vertical judgement. Press V on the control button until the LCD screen returns to the menu bar display in FILE SERIES Assigns numbers to files in sequence MOVIE step 1. To clear the menu bar, press V again. NUMBER even if the “Memory Stick” is changed. STILL xNORMAL Resets the file numbering each time the “Memory Stick” is changed. 31 32 Item Setting Description MODE Item Setting Description MODE selector selector IMAGE x1600×1200 Selects the image size when recording STILL PROTECT ON Protects images against accidental PLAY SIZE 1600 (3:2) still images (DSC-S50 only). erasure (page 49). 1024×768 xOFF Releases protection of images against 640×480 accidental erasure. 1472×1104 Selects the image size when recording STILL x1280×960 still images (DSC-S30 only). CAMERA 1280 (3:2) × Item Setting Description MODE 1024 768 selector 640×480 DIGITAL xON Uses digital zoom. STILL 320×240 Selects the MPEG image size when MOVIE ZOOM x160×112 recording moving images (DSC-S50 OFF Does not use digital zoom. only). SHARPNESS +2 to –2 Adjusts the sharpness of the image. STILL REC MODE TIFF Records a TIFF (uncompressed) file in STILL appears on the LCD screen except addition to the JPEG file. when set to 0. TEXT Records a GIF file in black-and-white. WHITE IN DOOR Sets the white balance (page 43). MOVIE

BALANCE

VOICE Records an audio file (with still image) OUT DOOR STILL in addition to the JPEG file (DSC-S50 HOLD only). xAUTO E-MAIL Records a small-size (320×240) JPEG FLASH HIGH Makes the flash level higher than STILL file in addition to the selected image LEVEL normal. size. xNORMAL Normal setting. xNORMAL Records a JPEG file in the selected LOW Makes the flash level lower than normal. image size. EXPOSURE +2.0 EV to Adjusts the exposure. MOVIE REC TIME 15 SEC Adjusts the recording time for moving MOVIE –2.0 EV STILL SET 10 SEC images (DSC-S50 only). x5 SEC

TOOL

ROTATE Rotates the still image. PLAY (in single — Item Setting Description MODE mode only) selector SLIDE INTERVAL Sets the slide show interval. PLAY COPY OK Copies an image (page 51). PLAY SHOW x3 SEC/5 SEC/10 SEC/30 SEC/1 MIN CANCEL Cancels copying of the image. (in single mode only) REPEAT Repeats the slide show. RESIZE 1600×1200 Changes the recorded still image size PLAY xON/OFF (in single 1024×768 (page 51) (DSC-S50 only). START Starts the slide show. mode only) 640×480 xCANCEL CANCEL Cancels the slide show settings and execution. 1472×1104 Changes the recorded still image size PLAY (page 51) (DSC-S30 only). PRINT ON Marks the still images to be printed PLAY 1280×960 MARK (page 53). 1024×768 640×480 xOFF Unmarks the print mark of the still xCANCEL images. 33 34 – 22 –

Before performing advanced operations Before performing advanced operations

, SETUP 3 (RETURN)** Returns to PLAY (single) mode. Item Setting Description MODE selector ∗ Displayed only in PLAY (single) mode. DEMO xON/STBY Displayed only when you use the AC MOVIE ∗∗ Displayed only in PLAY (INDEX) mode. OFF power adaptor in MOVIE or STILL STILL mode. When ON is selected, a demonstration will start if you do not operate your camera for about 10 minutes. To stop the demonstration, turn off your camera. Select ON to make the demonstration appear again. VIDEO xNTSC Sets the video output signal to NTSC MOVIE OUT mode (North American countries, Japan, STILL etc.). PLAY PAL Sets the video output signal to PAL mode (European countries, etc.). / xENGLISH Displays the menu items in English. MOVIE LANGUAG /JPN Displays the menu items in Japanese. STILL E PLAY CLOCK Sets the date and time (page 13). MOVIE SET — STILL

PLAY

BEEP SHUTTER Turns off the beep only. (The shutter MOVIE sound is heard when you press the STILL shutter button.) PLAY xON Turns on the beep/shutter sound (when you press the control button/shutter button). OFF Turns off the beep/shutter sound. LCD Adjusts the LCD screen brightness MOVIE BRIGHT using the +/– buttons on the LCD STILL screen. This has no effect on the PLAY recorded images. INDEX* Displays six images at a time (PLAY (INDEX) mode) (page 45).

DELETE

Setting Description MODE selector OK Deletes the displayed image. PLAY CANCEL Cancels deleting of the image. 35 36

B Various recording The number of images or the time Setting the image size that you can record on a “Memory Recording still images for e- Rotating the LCD screen — (IMAGE SIZE) Stick” (4 MB): mail (E-MAIL) Face-to-Face recording Image size Number of images or

1 time* E-MAIL mode records a small-size You can record images with the lens (320×240) image at the same time as a 1600× 120 Approx. 4 facing you. still image. Small-size images are 2,3 0 convenient for e-mail transmission, 1600 (3:2) Approx. 4 etc. 1472×110 Approx. 53243111280×960 Approx. 61 Set the MODE selector to MOVIE or STILL. 1280 (3:2) Approx. 6 2 (MOVIE is for DSC-S50 only) 1024×768 Approx. 10 2 Select [FILE] and then 640×480 Approx. 57 [IMAGE SIZE] from the menu. 320×240 Approx. 42 (15**) sec. 3 Select the desired image 1 Set the MODE selector to 160×112 Approx. 169 (60**) sec. size. STILL.1 Set the MODE selector to ∗ When [REC MODE] is set to MOVIE or STILL. DSC-S50: 2 Select [FILE], [REC MODE], [NORMAL]. Still image sizes and then [E-MAIL] from the 2 Adjust the angle of the LCD × ∗∗ Numbers in parentheses indicate the 1600 1200, 1600 (3:2), menu. screen. maximum recording time during ° 1024×768, 640 ×480Rotate the LCD screen by 180 for continuous recording. 3 Record the image. Face-to-Face recording. Moving image sizes The number of images that you can 320×240, 160 ×112 When [1600 (3:2)], [1280 (3:2)] is 3 Record the image. record on a “Memory Stick” (4 MB) selected The image appears on the LCD DSC-S30: in E-MAIL mode.The image is recorded in 3:2 size to screen as a mirror image, but the Still image sizes match the printing paper size ratio of Image size Number of images recorded image is the same as the 1472×1104, 1280 ×960, 1280 3:2. actual subject. (3:2), 1024 ×768, 640 ×480 1600×1200 Approx. 3 1600 (3:2) Approx. 3 1472×1104 Approx. 4 1280×960 Approx. 5 1280 (3:2) Approx. 5 Image appearing Recorded image 1024×768 Approx. 9 on the LCD screen 640×480 Approx. 46 To return to normal recording mode Select [NORMAL] in step 2. 37 38 – 23 –

Before performing advanced operations B Various recording

, Notes

Adding audio files to still Recording text documents Recording uncompressed • JPEG images are recorded in the image

images (VOICE) (DSC-S50 (TEXT) images (TIFF) size selected by the [IMAGE SIZE] menu. only) TIFF images are recorded in [1600 ×1200] Text is recorded in black and white This mode simultaneously records still size in DSC-S50, and [1280 ×960] size in 3 GIF format to provide a clearer image. images in both TIFF format DSC-S30 other than when [1600 (3:2)] or [1280 (3:2)] is selected. 1 (uncompressed) and JPEG format 3 • Writing data takes more time than in (compressed). normal recording. 2 3 • The supplied “Memory Stick” (4 MB) does not have sufficient capacity to record21uncompressed images. 1 Set the MODE selector to STILL. 1 Set the MODE selector to 2 Select [FILE], [REC MODE], STILL. and then [VOICE] from the menu. 2 Select [FILE], [REC MODE], 1 Set the MODE selector to and then [TEXT] from the STILL. 3 Record the image. menu. 2 Select [FILE], [REC MODE], If you press and release the shutter 3 Record the image. and then [TIFF] from the button, sound is recorded for menu. 5 seconds. The number of images that you can record on a “Memory Stick” (4 MB) 3 Record the image. If you hold down the shutter in TEXT mode: The number of images that you can button, sound is recorded until you Image size Number of images record on a “Memory Stick” release the shutter button for up to (16 MB) in TIFF mode: 40 seconds. 1600×1200 Approx. 12 to 87 Image size Number of images The number of images that you can 1600 (3:2) Approx. 14 to 97 record on a “Memory Stick” (4 MB) 1600×1200 Approx. 21472×1104 Approx. 14 to 97 in VOICE mode (when recording 1600 (3:2) Approx. 2 1280×960 Approx. 20 to 114 sound for five seconds): 1280×960 Approx. 3 1280 (3:2) Approx. 22 to 137 Image size Number of images 1280 (3:2) Approx. 3 1024×768 Approx. 30 to 160 1600×1200 Approx. 3 640×480 Approx. 80 to 363 To return to normal recording mode 1600 (3:2) Approx. 3 Select [NORMAL] in step 2. 1024×768 Approx. 8 To return to normal recording mode 640×480 Approx. 28 Select [NORMAL] in step 2. Notes To return to normal recording mode • If the subject is not evenly illuminated, you Select [NORMAL] in step 2. may be unable to record a clear image. • Writing and reading data takes more time When using the DSC-S30 than in normal recording. The DSC-S30 does not have a VOICE • The flash does not strobe in TEXT mode function. When you edit (delete, protect, or regardless of the surrounding brightness. copy files, etc.) files recorded in VOICE mode on a different camera, the still image file is edited but the audio file is not. 39 40 Landscape mode

Recording images in macro Setting the distance to the Using the PROGRAM AE Focuses only on a distant subject

subject function to record landscapes, etc. 1 Panfocus mode 2 Normally the focus is automatically Changes the focus quickly and adjusted. This function is useful when 1 simply from a close subject to a the auto focus does not work well such distant subject. as in dark places. +/– Spot light-metering mode 1 Select this mode when there is22backlight or when there is strong 1 Set the MODE selector to contrast between the subject and MOVIE or STILL. the background, etc. Position the 1 Set the MODE selector to point you want to record on the 2 Press FOCUS repeatedly MOVIE or STILL. spot light-metering cross hair. until the (auto macro) indicator appears on the LCD 2 Press PROGRAM AE LCD screen screen. 1 Set the MODE selector to repeatedly to select the You can record a subject as close MOVIE or STILL. desired PROGRAM AE mode. as about 1 3/16 inches (3 cm) from 2 Press FOCUS repeatedly to A Aperture priority mode the lens surface with the zoom set all the way to the W side. achieve a sharp focus. Makes the subject stand out The 9 (manual focus) indicator against an unclear background or Spot light-metering makes both the subject and the cross hair To return to normal recording mode appears on the LCD screen. You can select from the following background stand out clearly. Press FOCUS repeatedly until 7 focus settings: auto (no Press +/– repeatedly to select an To cancel PROGRAM AE disappears from the LCD screen. indicator), (auto macro), aperture value in 9 steps from F2.8 Press PROGRAM AE repeatedly until to F11. Notes 1 3/4 feet (0.5m), 3 1/4 feet the indicator on the LCD screen goes • (1.0m), 9 3/4 feet (3.0m), 23 feet You cannot record images in macro with S Shutter speed priority out. the following PROGRAM AE modes. (7.0m), ∞ (infinite) mode — Landscape mode Records a sharp picture of a fast- Notes — Panfocus mode To reactivate auto focusing moving subject or the flow of • You cannot select F2.8 in aperture priority • You cannot record images in macro when Press FOCUS repeatedly until the motion of a moving subject. mode when the zoom is set to the T side. appears on the LCD screen. indicator disappears in step 2. • You can focus only on distant subjects in Press +/– repeatedly to select a Landscape mode. shutter speed in 18 steps from 8” • In Panfocus mode, the zoom position and Note to 1/725 when recording a still focus are fixed. These setting distances are approximate, and image and in 12 steps from 1/8 to • When you record in the Twilight plus should be used as a reference. 1/725 when recording a moving mode, we recommend that you use a tripod image. to prevent shaking. • Set the forced flash when you use the Twilight mode flash in the following modes: Suppresses the washed-out color –Twilight mode –Twilight plus mode of a bright subject in a dark place –Landscape mode so that you can record the subject • You cannot use the PROGRAM AE without losing the dark function when [REC MODE] is set to atmosphere of the surroundings. [TEXT]. • If the setting is not appropriate in aperture Twilight plus mode priority mode and shutter priority mode, Increases the effectiveness of the the setting value indicator on the LCD twilight mode function. screen flashes when you press the shutter button. In this case, reset the value. 41 42 – 24 –

B Various recording B Various recording

,

Adjusting the exposure Adjusting the white balance Recording the date and time Enjoying picture effects

(EXPOSURE) (WHITE BALANCE) on the still image (DATE/ (P.EFFECT) Normally the white balance is TIME) 1 automatically adjusted. 4 1 2,3112,3 2,3 2,3 1 Set the MODE selector to 1 Set the MODE selector to MOVIE or STILL. 1 Set the MODE selector to MOVIE or STILL. 2 1 Set the MODE selector to Select [CAMERA] and then STILL. MOVIE or STILL. 2 Select [EFFECT] and then [EXPOSURE] from the menu. 2 Select [EFFECT] and then [P.EFFECT] from the menu. 3 2 Select [CAMERA] and then Select the desired exposure [DATE/TIME] from the menu.[WHITE BALANCE] from the 3 Select the desired mode. value. menu. 3 Select the date and time Adjust the exposure value while SOLARIZE setting. checking the brightness of the 3 Select the desired white The light contrast is clearer and the background. You can select values balance setting. DAY&TIME picture looks like an illustration. ranging from +2.0 EV to –2.0 EV The date, hour and minutes are IN DOOR (n) B&W in steps of 1/3 EV. imposed onto the image.• Places where the lighting The picture is monochrome (black Note condition changes quickly DATE and white). • Under bright lighting such as The year, month and day are The exposure may not be adjusted properly SEPIA imposed onto the image. when the subject is extremely bright or dark, photography studios The picture is colored like an old or when using the flash. • Under sodium or mercury lamps OFF picture. OUT DOOR ( ) The date and time are not imposed NEG.ART Recording a sunrise/sunset, night onto the image. The color and brightness of the scene, neon signs, or fireworks 4 Record the image. picture are reversed. HOLD The date and time are not displayed during recording. To cancel picture effect Recording a single-colored subject or background The date and time are displayed Select [OFF] in step 3. when playing back images. AUTO (No indicator) Adjusts the white balance automatically To reactivate auto adjustment Select [AUTO] in step 3. Note Select [AUTO] when recording under fluorescent lighting. 43 44

B Various playback To display the next (previous) index Notes

screen Enlarging a part of the still • You cannot trim images recorded in TEXT

Playing back six images at Select v/V at the lower left of the LCD image (Zoom and trimming)

mode or uncompressed images. • The maximum zoom magnification is 5× once (INDEX) screen. 1 the original image, regardless of the image size. Displays the previous • The picture quality of trimmed images 1 index screen 3 may deteriorate. 2,4 • The original picture remains even after 2 Displays the next index trimming.screen • The trimmed image is recorded as the newest file. To return to normal playback (single image) 1 Set the MODE selector to 1 Set the MODE selector to • PLAY. Select the desired image with the PLAY. control button. 2 Display the image to be 2 • Select [3] (RETURN). enlarged. Select [INDEX] on the LCD screen. Note 3 Zoom in/out the image with Six images are displayed at once You cannot display images recorded in the zoom button. (index screen). TEXT mode on the INDEX screen. The zoom scaling indicator appears on the LCD screen. 4 Press the control button repeatedly to select the desired part of the image. v: The image moves downward V: The image moves upward b: The image moves rightward B: The image moves leftward This shows the position of the currently displayed images relative To return to the normal size to all the recorded images. Zoom in with the zoom button until the The following marks are displayed zoom scaling indicator ( × 1.1) on each image according to the disappears from the screen, or simply image type and settings. press z. : Moving image file : Voice memo file To record an enlarged image : E-mail file (trimming) : Print mark - : Protect mark 1Enlarge the image. TEXT: Text mark 2Press the shutter button. The image TIFF: TIFF mark is recorded at 640× 480 size, then the (No mark): Normal recording (no display returns to the image display settings) before enlargement. 45 46 – 25 –

B Various recording B Various playback

, Note

Rotating a still image Playing back the images in The [INTERVAL] setting time is Viewing images on a TV

(ROTATE) order (SLIDE SHOW) approximate, and may vary depending on screen the played back image size or other factors. This function is useful for checking the Before connecting your camera, be 1 recorded images or for presentations, sure to turn off the TV. After etc. connecting A/V connecting cable 2,3,4 (DSC-S50) or VIDEO connecting cable (DSC-S30), turn on the TV. 2,3 Set the TV/VIDEO switch to VIDEO. 1 Set the MODE selector to PLAY. A/V connecting cable or 2 VIDEO connecting cable Display the image to rotate. (supplied) 3 Select [FILE] and then 1 Set the MODE selector to [ROTATE] from the menu. PLAY. 4 Rotate the image clockwise 2 Select [FILE] and then [SLIDE or counterclockwise , SHOW] from the menu. then select [RETURN]. Set the following items. INTERVAL to A/V OUT jack or Notes 1 MIN (one minute), 30 SEC VIDEO OUT jack • You may not be able to rotate protected (30 seconds), 10 SEC images or images recorded with other (10 seconds), 5 SEC (5 seconds), equipment. 3 SEC (3 seconds) 1 Connect your camera and the • Also, when viewing images on a personal TV. computer, the image rotation information REPEAT DSC-S50 may not be reflected depending on the ON: Plays back images in a application software. Connect the A/V connecting cable continuous loop until • You cannot rotate protected or to the A/V OUT jack of your [RETURN] is selected. uncompressed images, or images recorded camera and to the audio/video in TEXT mode. OFF: After all images have been input jacks of the TV. played back, the slide show ends. If your TV has stereo type audio input jacks, connect the audio plug 3 Select [START] with the of the A/V connecting cable to the control button. Lch jack. The slide show begins. DSC-S30 Connect the video cable to the To cancel the slide show VIDEO OUT jack of your camera Select [CANCEL] in step 2 or 3. and to the video input jack of the TV. To skip to the next/previous image during slide show playback 2 Turn on the TV, then start playback on your camera. Select b/B at the lower left of the LCD The playback image appears on screen. the TV screen. Note You cannot use a TV that has an antenna 47 48 (aerial) connector only.

B Editing The selected images are protected. The (delete) indicator appears Deleting images (DELETE) on the selected images and these Preventing accidental erasure images are deleted.You cannot delete protected files.

(PROTECT) The - (protect) indicator appears on 1 protected images. 1,2,3 1 To release protection If you selected [ALL] in step 2, select 1,2,3 [OFF]. If you selected [SELECT] in To cancel deleting step 2, select the images to unprotect In single mode Select [CANCEL] in step 2 or 3. with the control button, then select [ENTER]. 1 Set the MODE selector to Note PLAY, then display the image If there are files on the “Memory Stick” with

In single mode to delete. names having the same last 4 digits as the

file name of the image to be deleted, these 1 Set the MODE selector to 2 Select [DELETE] and then files are also deleted at the same time. PLAY, then display the image [OK] from the menu. to protect. The image is deleted. 2 Select [FILE], [PROTECT], and then [ON] from the menu. In INDEX mode The displayed image is protected and - appears. 1 Set the MODE selector to PLAY, then display the INDEX To release protection screen. Select [OFF] in step 2. 2 Select [DELETE] and then [ALL] or [SELECT] from the menu.

In INDEX mode

3 When you select [ALL] 1 Set the MODE selector to Select [ENTER]. PLAY, then display the INDEX All unprotected images are screen. deleted. 2 Select [FILE], [PROTECT], When you select [SELECT] and then [ALL] or [SELECT] Select all the images to delete with from the menu. the control button, then select 3 When you select [ALL] [ENTER]. Select [ON]. All the images recorded in “Memory Stick” are protected. When you select [SELECT] Select all the images to protect with the control button, then select [ENTER]. 49 50 – 26 –

B Various playback B Editing

, After copying is finished

Changing the recorded still Copying images (COPY) In INDEX mode Select [EXIT].

image size (RESIZE) If you do not select [EXIT], the same You can copy images to another image is copied each time you “Memory Stick.” 1 exchange the “Memory Stick.” 1,2,3 In single mode 1,2,3,4 To cancel copying part-way Change the MODE selector setting or turn off the power. 1 Notes Set the MODE selector to 1,2 • You cannot copy uncompressed images.1 PLAY, then display the INDEX Set the MODE selector to • You cannot copy images that are bigger screen. PLAY and display the image than 1.4 MB at once. If “NOT ENOUGH to resize. 2 Select [TOOL], [COPY], and MEMORY” appears or flashes on the INDEX screen, cancel some images to 2 then [SELECT] from the Select [TOOL] and then 1 copy and try again. Set the MODE selector to menu. [RESIZE] from the menu. PLAY, then display the image 3 to copy. 3 Select the image to copy.Select the desired image The (select) indicator appears size. 2 Select [TOOL], [COPY], and on the image. DSC-S50 then [OK] from the menu. “FILE ACCESS” appears. 4 Select [ENTER].1600×1200, 1024 ×768, 640 ×480 “MEMORY STICK ACCESS” DSC-S30 3 When “CHANGE MEMORY appears. 1472×1104, 1280 ×960, STICK” appears, eject the “Memory Stick.” 5 When “CHANGE MEMORY 1024×768, 640× 480 “INSERT MEMORY STICK” STICK” is displayed, eject the The changed image is recorded, appears. “Memory Stick.” “INSERT MEMORY STICK” then the display returns to the 4 Insert the “Memory Stick” on appears. image display before resizing. which to copy the image. “RECORDING” appears. When 6 Insert another “Memory To return to the original size copying is completed, Stick.” Select [CANCEL] in step 3. “COMPLETE” appears. “RECORDING” appears. When If you exchange the “Memory copying is completed, Notes Stick,” the same image is copied “COMPLETE” appears. • You cannot change the size of images again. If you exchange the “Memory recorded in TEXT mode or uncompressed Stick,” the same image is copied images. again. • When you change from a small size to a After copying is finished large size, the picture quality deteriorates. Select [EXIT]. • The original image is retained even after If you do not select [EXIT], the same resizing. image is copied each time you • The resized image is recorded as the exchange the “Memory Stick.” newest file. 51 52 4 Select [ENTER]. Additional information How to prevent moisture Selecting still images to print of the selected images change condensation (PRINT MARK) from green to white. Precautions When bringing the camera from a cold place to a warm place, seal the camera in a plastic You can mark a print mark on still bag and allow it to adapt to conditions at the images recorded with your camera. On cleaning new location over a period of time (about an This mark is convenient when you hour). have images printed at a shop that Cleaning the LCD screen If moisture condensation occurs conforms with the DPOF (Digital Print Wipe the screen surface with a cleaning cloth (not supplied) or a LCD cleaning kit Turn off the camera and wait about an hour Order Format) standard. (not supplied) to remove fingerprints, dust, for the moisture to evaporate. Note that if etc. you attempt to record with moisture 1 To unmark selected print marks remaining inside the lens, you will be Select the images to unmark in step 3 Cleaning the camera surface unable to record clear images. Clean the camera surface with a soft cloth 1,2,3,4 with the control button, then select [ENTER]. slightly moistened with water, then wipe the surface dry. Do not use any type of solvent On AC power adaptor such as thinner, alcohol or benzene as this To unmark all the print marks may damage the finish or the casing. • Unplug the unit from the wall outlet Select [FILE], [PRINT MARK], (mains) when you are not using the unit for After using your camera at the a long time.

In single mode [ALL] and then [OFF] from the menu. seashore or other dusty locations • To disconnect the power cord (mains lead),

of all images are unmarked. 1 Clean your camera carefully. Otherwise, the pull it out by the plug. Never pull the Set the MODE selector to salty air may corrode the metal fittings or power cord (mains lead) itself. PLAY and display the image Notes dust may enter the inside of your camera, • Do not operate the unit with a damaged you want to print. • You cannot mark moving images or causing a malfunction. cord or if the unit has been dropped or images recorded in TEXT mode. damaged. 2 Select [FILE], [PRINT MARK], • If you mark an image recorded in TIFF • Do not bend the power cord (mains lead) and then [ON] from the menu. mode with a print mark, only the Note on operating forcibly, or place a heavy object on it. This The (print) mark is displayed uncompressed image is printed, and the temperature will damage the cord and may cause fire or on the image. JPEG image recorded at the same time is Your camera is designed for use between the electrical shock. not printed. temperatures of 32˚F and 104˚F (0˚C and • Prevent metallic objects from coming into To unmark the print mark 40˚C). Recording in extremely cold or hot contact with the metal parts of the places that exceed this range is not connecting section. If this happens, a short Select [OFF] in step 2. recommended. may occur and the unit may be damaged. • Always keep metal contacts clean. • Do not disassemble the unit.

In INDEX mode On moisture condensation • Do not apply mechanical shock or drop the

1 unit.Set the MODE selector to If the camera is brought directly from a cold • While the unit is in use, particularly during PLAY, then display the INDEX to a warm location, or is placed in a very charging, keep it away from AM receivers screen. damp room, moisture may condense inside and video equipment. AM reception and or outside the camera. Should this occur, the 2 video operation are disturbed.Select [FILE], [PRINT MARK], camera will not operate properly. • The unit becomes warm during use. This is and then [SELECT] from the Moisture condensation occurs not a malfunction. menu. easily when: • Do not place the unit in locations that are: 3 — Extremely hot or coldSelect the images to mark • The camera is brought from a cold location such as a ski slope into a warmly heated — Dusty or dirtywith the control button. room. — Very humid • The camera is taken from an air- — Vibrating conditioned room or car interior to the hot outdoors, etc. 53 54 – 27 –

B Editing B Editing

,

On battery pack “Memory Stick”, , “MagicGate PAL-M system countryOn “Memory Sticks” Memory Stick” and are trademarks of Brazil

• Use only the specified charger with the Sony Corporation. charging function. “Memory Stick” is a new compact, portable “MagicGate” and are PAL-N system countries • To prevent accident from a short circuit, do and versatile IC recording medium with a trademarks of Sony Corporation. Argentina, Paraguay, Uruguay not allow metal objects to come into data capacity that exceeds a floppy disk. “Memory Stick” is specially designed for SECAM system countriescontact with the battery terminals. • Keep the battery pack away from fire. exchanging and sharing digital data among Bulgaria, Czech Republic, France, • Never expose the battery pack to “Memory Stick” compatible products. Using your camera abroad Guiana, Hungary, Iran, Iraq, Monaco, temperatures above 140˚F (60˚C), such as Because it is removable, “Memory Stick” Poland, Russia, Slovak Republic, in a car parked in the sun or under direct can also be used for external data storage. Power sources Ukraine, etc. sunlight. You can use your camera in any • Keep the battery pack dry. There are two types of “Memory Sticks”: country or area with the supplied • Do not expose the battery pack to any general “Memory Sticks” and “MagicGate battery charger within 100 V to 240 V mechanical shock. Memory Sticks” that are equipped with the • Do not disassemble nor modify the battery MagicGate* copyright protection AC, 50/60 Hz. Use the supplied AC pack. technology. power adaptor [a], if necessary, • Install the battery pack to the camera You can use both types of “Memory Stick” depending on the design of the wall securely. with your camera. However, because your outlet (mains) [b]. • Charging while some capacity remains camera does not support the MagicGate does not affect the original battery standards, data recorded with your camera is capacity. not subject to MagicGate copyright AC-L10 protection. If any problem occurs, unplug your camera ∗ MagicGate is copyright protection and contact your nearest Sony dealer. technology that uses encryption technology.

On internal rechargeable Watching the playback picture on Notes

button battery TV• Do not remove the “Memory Stick” while If you want to view the playback This camera has an internal rechargeable reading or writing data. picture on a TV, you need a TV having button battery for maintaining the date and • Data may be damaged if: — you remove the “Memory Stick” or turn a video input jack and a video time and other settings regardless of whether the power is on or off. This off your camera while reading or connecting cable. writing data. The color system of the TV must be rechargeable button battery is constantly charged as long as you are using the camera. — you use the “Memory Stick” in a the same as that of your digital still However, if you use the camera for only location subject to the effects of static camera. TV color systems differ from short periods it discharges gradually, and if electricity or noise. country to country. Check the you do not use the camera at all for about • Do not attach any other material than the following list: half a year it becomes completely supplied label on the labeling position. discharged. In this case, be sure to charge • Attach the label so that it does not stick out NTSC system countries this rechargeable button battery before using from the proper attachment location. Bahama Islands, Bolivia, Canada, the camera. • When you carry or store the “Memory Central America, Chile, Columbia, However, even if this rechargeable button Stick,” put it in its supplied case. Ecuador, Jamaica, Japan, Korea, battery is not charged, you can still use the • Do not touch the terminals of a “Memory Mexico, Peru, Surinam, Taiwan, the camera as long as you do not record the date Stick” with your hand or a metal object. Philippines, the U.S.A., Venezuela, etc. and time. • Do not strike, bend or drop the “Memory Stick.” PAL system countries Charging method • Do not disassemble or modify the Australia, Austria, Belgium, China, Connect the camera to a wall outlet (mains) “Memory Stick.” • Do not allow the “Memory Stick” to get Denmark, Finland, Germany, Great with the AC power adaptor, or install a wet. Britain, Holland, Hong Kong, Italy, charged battery pack, and leave the camera for 24 hours or more with the POWER Kuwait, Malaysia, New Zealand, switch set to OFF. Norway, Portugal, Singapore, Spain, Sweden, Switzerland, Thailand, etc. 55 56

Troubleshooting Symptom Cause and/or Solution

The picture is too dark. • You are shooting a subject with a light source If you experience trouble with your camera, first check the following items. Should behind the subject. your camera still not operate properly after you have made these checks, consult your tAdjust the exposure (page 43). Sony dealer or local authorized Sony service facility. If code displays (C:ss:ss) tAdjust the brightness of the LCD screen (page appear on the LCD screen, the self-diagnosis display function is working (page 62). 35). The flash does not work. • The flash is set to . Symptom Cause and/or Solution tSet the flash to auto (no indicator), or (page 19). Your camera does not • You are not using an “InfoLITHIUM” battery pack. work. • PROGRAM AE is set to the Twilight, Twilight tUse an “InfoLITHIUM” battery pack (page 8). plus, or Panfocus mode. • The battery level is low (the E indicator appears tCancel the mode (page 42) or set the flash to on the LCD screen).tCharge the battery pack (page 9). • The MODE selector is set to MOVIE (DSC-S50 • The AC power adaptor is not connected securely. only). tConnect it firmly to the DC IN jack of your tSet it to STILL. camera and a wall outlet (mains) (page 12). • The built-in microcomputer is not working The date and time are • The date and time are not set correctly. properly. recorded incorrectly. tSet the correct date and time (page 13). tDisconnect and then reconnect all power Vertical streaks appear • The smear phenomenon is happening. sources after one minute. Then turn the power when you are shooting a tThis is not a malfunction. on by sliding the POWER switch down and very bright subject. check that the camera works properly. The battery life is short. • You are recording/playing back images under Your camera cannot • The MODE selector is set to PLAY. extremely cold temperatures. record images. tSet it to MOVIE or STILL (pages 16, 20). • The battery pack is not charged enough. • No “Memory Stick” has been inserted into your tCharge the battery pack fully. camera. • The battery pack is dead. t Insert a “Memory Stick” (page 15). tReplace the battery pack with a new one. • The write-protect tab on the “Memory Stick” is set The battery remaining • You have used the camera for a long time in an to LOCK. indicator is incorrect. extremely hot or an extremely cold location. tSet it to the recording position. • The battery pack is dead. The picture is out of focus. • Your camera is not in macro recording mode when tReplace the battery pack with a new one (page you shoot a subject that is about 1 3/16 to 8). 9 7/8 inches (3 to 25 cm) away from the lens. • The battery pack is discharged. tSet the macro recording mode (page 41). t Install a charged battery pack (pages 8, 9). tPress the zoom button to set to the W side. Sufficient battery tFully charge the battery pack (page 9). The resizing function does • You cannot resize moving images and text images. remaining indicator is not work. displayed but the power runs out soon. You cannot display a print • You cannot display print marks on moving images mark. and text images. The zoom does not work. • PROGRAM AE is set to the Panfocus mode. The picture is noisy. • Your camera is placed near a TV or other tCancel the Panfocus mode (page 42). equipment that uses strong magnets. Digital zoom does not • You cannot use digital zoom to record moving tMove your camera away from the TV, etc. function. pictures. 57 58 – 28 –

Additional information Additional information

, Symptom Cause and/or Solution Symptom Cause and/or Solution Your camera cannot play • The MODE selector is set to STILL or MOVIE. Your personal computer • The camera is turned off. back images. tSet it to PLAY (page 21). does not recognize your tTurn on the camera. The image and sound • You are playing back the file directly from the camera. • The battery level is low. break off when you play “Memory Stick.” tUse the AC power adaptor (page 12). back an image on a tCopy the file to the hard disk of the personal • The USB cable is not connected firmly. personal computer. computer and then play back the file from the tDisconnect the USB cable, and connect it again hard disk (page 27). firmly. Make sure that “PC MODE” is displayed The image cannot be tConsult the personal computer or software on the LCD screen (page 26). played back on a personal manufacturer. • The USB connectors on your personal computer computer. are connected to other equipment besides the keyboard, the mouse, and your camera. Your camera cannot delete • The image is protected. an image. tDisconnect the USB cables except for the ones tCancel the protection (page 49). connected to the keyboard, the mouse, and your The power turns off • With the MODE selector set to STILL or MOVIE, camera (page 24). suddenly. if you do not operate the camera for about three minutes while the power is on, the camera turns off automatically to prevent wearing down the battery. tTurn on the camera. • The battery is discharged. tReplace it with a charged battery. The image does not • The video output signal setting of your camera is appear on the TV screen. incorrect. tChange the setting (page 48). A file error occurs when • The image size is larger than 1600 ×1200. you play back a file. tUse an image size of 1600 ×1200 or smaller. The PROGRAM AE • The camera is set to text mode. function does not work. tCancel text mode (page 42). The LCD screen freezes • This is a characteristic of the system and is not a momentarily. malfunction. 59 60

Warning and notice messages Self-diagnosis display

Various messages appear on the LCD screen. Check the corresponding descriptions Your camera has a self-diagnosis display. This in the following list. function displays the camera condition on the LCD screen with a combination of a letter and Message Meaning four digits of numbers. If this occurs, check the following code chart. The code informs you of the NO MEMORY STICK No “Memory Stick” has been inserted. camera’s current condition. The last two digits SYSTEM ERROR Turn the power off and on again. (indicated by ss) will differ depending on the state of the camera. MEMORY STICK ERROR The inserted “Memory Stick” cannot be used with your camera, or is damaged. Self-diagnosis display FORMAT ERROR Failed to format the “Memory Stick.” • C:ss:ss You can reverse the camera MEMORY STICK LOCKED The write-protect tab on the “Memory malfunction yourself. Stick” is set to the LOCK position. • E:ss: ss Contact your Sony dealer or local NO MEMORY SPACE The capacity of the “Memory Stick” is authorized Sony service facility. full, and you cannot record or copy images. First three digits Cause and/or Corrective Action NO FILE No image has been recorded on the C:32:ss • There is trouble with your camera’s hardware. “Memory Stick.” tTurn the power off and on again. FILE ERROR An error occurred while playing back the image. C:13:ss • An unformatted “Memory Stick” is inserted. tFormat the “Memory Stick” (page 32). FILE PROTECT The image is protected against erasure. • The inserted “Memory Stick” cannot be used with for “InfoLITHIUM” battery only The battery is not the “InfoLITHIUM” your camera, or is damaged. type. t Insert a new “Memory Stick” (page 15). NOT ENOUGH MEMORY The images you want to copy are too big E:61:ss • A camera malfunction that you cannot reverse has to copy with your camera. E:91:ss occurred. DIRECTORY ERROR A directory with the same name already tContact your Sony dealer or local authorized exists. Sony service facility and inform them of the 5- digit service code. (example: E:61:10) IMAGE SIZE OVER You are playing back an image of a size that cannot be played back with your If you are unable to solve the problem even after trying the corrective camera. actions a few times, contact your Sony dealer or local authorized Sony INVALID OPERATION You are playing back a file that was service facility. created on equipment other than your camera. E The battery level is low or zero. - The image is protected. 61 62 – 29 –

Additional information Additional information

,

LCD screen indicators The indicators during recording

A Battery remaining indicator J Self-diagnosis function/ recording time indicator B PROGRAM AE/flash level/flash mode indicator K Number of recorded images C White balance/EV level/ L Remaining memory capacity sharpness indicator indicator D Picture effect indicator M Moving image/VOICE recording time indicator (DSC-S50 only) E Date/time indicator N Self-timer indicator F Aperture/shutter speed indicator O Spot light-metering indicator G AE lock/focus lock indicator P Focus/macro mode indicator H Recording mode indicator Q Menu bar and guide menu I Image size indicator They appear by pressing v on the control button and disappear by pressing V of it. – 30 –,

DSC-S30/S50 Sony EMCS Co. 2004G0500-19-929-819-41 © 2004. 7

– 32 – Published by DI Technical Support Section,

DSC-S30/S50

AEP Model UK Model

SERVICE MANUAL

Level 1 Ver 1.1 2000. 09

SUPPLEMENT-1

File this supplement with the service manual. (PV00-007) • Change of service parts.,

DSC-S30/S50

3. REPAIR PARTS LIST 3-1. EXPLODED VIEWS & : Points added portion. NOTE: - : Points changed portion. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay 3-1-1. FRONT PANEL SECTION should be anticipated when ordering these items. (Service manual page 11) Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3950-656-1 CABINET (FRONT) ASSY (S50) 1 X-3950-656-3 CABINET (FRONT) ASSY (S50) [ 1 X-3950-664-1 CABINET (FRONT) ASSY (S30) 1 X-3950-664-3 CABINET (FRONT) ASSY (S30) [ 10 X-3950-659-1 CABINET (UPPER) ASSY (S50) 10 X-3950-659-4 CABINET (UPPER) ASSY (S50) [ 10 X-3950-665-1 CABINET (UPPER) ASSY (S30) 10 X-3950-665-4 CABINET (UPPER) ASSY (S30) [ 3-1-2. MAIN SECTION 52 (Service manual page 12) 52 52 BT901 not supplied 68 ] & 71 not supplied Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3950-655-1 HOLDER ASSY, BT 51 X-3950-655-3 HOLDER ASSY, BT [ * 71 3-062-855-01 TAPE (40) ) – 2 –,

DSC-S30/S50

3-1-3. REAR CABINET SECTION (Service manual page 13) -109 113 115 119 A not 110 supplied 110 [ 120 108 122 107 108 123 106 124

A

126 125 104 135 103 129 not supplied 102 134 108 128 Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 109 X-3950-658-1 CABINET (REAR) ASSY (S50) 109 X-3950-658-3 CABINET (REAR) ASSY (S50) [ 109 X-3950-794-1 CABINET (REAR) ASSY (S30) 109 X-3950-794-3 CABINET (REAR) ASSY (S30) [ * 133 3-062-736-01 SHEET, ELECTROSTATIC Not Supplied [ – 3 –,

DSC-S30/S50

9-929-819-81 Sony EMCS Co. 2000I0520-1Printed in Japan © 2000. 9 – 4 – Published by DI Customer Center,

DSC-S30/S50 AEP Model UK Model SERVICE MANUAL Level 1 Ver 1.2 2001. 10 SUPPLEMENT-2

File this supplement with the service manual. (PV01-009) • Change of Service Parts. 3. REPAIR PARTS LIST 3-1. EXPLODED VIEWS - : Points changed portion. 3-1-3. REAR CABINET SECTION (Service manual page 13) Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 109 X-3950-658-3 CABINET (REAR) ASSY (S50) 109 X-3950-658-4 CABINET (REAR) ASSY (S50) [ 109 X-3950-794-3 CABINET (REAR) ASSY (S30) 109 X-3950-794-4 CABINET (REAR) ASSY (S30) [ 9-929-819-84 Sony EMCS Co. 2001J0500-1© 2001. 10 Published by DI Customer Center,

Reverse 992981943.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2000.04 Official Release — — 1.1 2000.09 Supplement-1 • Change of Service Parts No (S1 PV00-007) 1.2 2001.10 Supplement-2 • Change of Service Parts No (S2 PV01-009) 1.3 2004.07 Correction-1 • Correction of EXPLODED VIEWS Yes (C1) S.M. correction: Page 13]
15

Similar documents

SAFETY-RELATED COMPONENT WARNING!!
DSC-S30/S50 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.1 2000. 09 With SUPPLEMENT-1 (9-929-819-81) Photo: DSC-S30 SPECIFICATIONS System Output connector Operation temperature Storage temperature Image device A/V OUT (Monaural) 32˚F to 104˚F –4˚F to +140˚F 1/2.7 type color CCD (DSC-S50 only) (0˚
- : Points changed portion.
DSC-S30/S50 US Model Canadian Model SERVICE MANUAL AEP ModelUK Model Level2EModel Hong Kong Model Ver 1.3 2004. 07 Australian Model Chinese Model Korea Model Tourist Model Japanese Model CORRECTION-1 File this correction with the service manual. • Correction of SCHEMATIC DIAGRAMS • Correction of EXP
DSC-R1 SERVICE MANUAL LEVEL 2 US Model UK Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model
DSC-R1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.11 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FR
Supplied accessories
DSC-S30/S50 SERVICE MANUAL US Model Ver 1.1 2000. 09 Canadian ModelLevel 2 With SUPPLEMENT-1(9-929-819-82) AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model as
! : Points deleted portion.
DSC-S40 Auto-ADJ SERVICE MANUAL Ver 1.1 2005.11 CORRECTION-1 We will inform you that there are printing errors in the service manual previously issued. • Correction of the Before starting adjustment • Correction of the Table 6-1-1 • Correction of the Service tool DSC-S40 2005K0500-1© 2005.11 9-876-8
& : Points added portion.
DSC-S40 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.2 2005.09 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model SUPPLEMENT-1 Tourist Model File this supplement with the service manual. (PV05-041) • Change of Repair Parts Suffix No. of ST-11
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.06 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
TABLE OF CONTENTS
DSC-S30/S50 SERVICE MANUAL US Model Canadian Model Level 3 Ver 1.1 2000. 09 With SUPPLEMENT 1 AEP Model (9-929-819-83) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model a
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS [System] USB communication
DSC-S45 SERVICE MANUAL US Model Ver 1.0 2006.03 Revision History How to use Acrobat Reader Internal memory ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont cr
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.2 2006.09 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.1 2006.07 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
SAFETY CHECK-OUT
DSC-S600 SERVICE MANUAL LEVEL 3 US Model Ver. 1.1 2006. 07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SERVICE NOTE SCHEMATIC DIAGRAMS REPAIR PARTS LIST F
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model E Model Australian Model Chinese Model Brazilian Model Hong Kong Model Korea Model Link SPECIFICATIONS ACCESSORIES SELF-DIAGNOSIS FUNCTION INSTRUCTION MANUAL Note : Note : The components iden
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 1 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/Silver Argentine Model Lin
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.0 2005.03 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.2 2001.07 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service
SAFETY-RELATED COMPONENT WARNING!!
DSC-S75 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.2 2001. 11 SPECIFICATIONS System Flash General AC-L10A/B/C Accessories Image device Recommended recording Used battery pack AC power adaptor A/V connecting cable (1) 8.93 mm (1/1.8 type) color distance (ISO is set to AUTO): NP-FM50 Power requir
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.3 2002.09 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service
SPECIFICATIONS System Output connector General AC-L10A/B/C NP-FM50 battery pack
DSC-S85 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Differences Manual This Service Manual covers only differences from DSC-S75 (Level 2). In performing repair, refe
SPECIFICATIONS System Output connector General AC-L10A/B/C NP-FM50 battery pack
DSC-S85 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Differences Manual This Service Manual covers only differences from DSC-S75 (Level 2). In performing repair, refe
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
DSC-S75 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.2 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-68 board SY-68 board This service
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2003. 10 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004. 03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
DSC-T1 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2004. 03 Canadian Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model
DSC-T1 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2004. 03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
• Change of Automatic Adjustment Program • Change of Message for Destination Data
DSC-T100 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.04 SUPPLEMENT-1 File this supplement with the service manual. (DI07-003) • Change of Automatic Adjustment Program • Change of Message for Destination Data Write • Addition of [Read], [Save], and [Load] buttons to Angular Velocity Sensitivity Adjustment