Download: Supplied accessories

DSC-S30/S50 SERVICE MANUAL US Model Ver 1.1 2000. 09 Canadian ModelLevel 2 With SUPPLEMENT-1(9-929-819-82) AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service manual procides the information that is premised the Schematic diagram ... Pages 4-15 to 4-30 circuit board replacement service and not intended repair inside the Ptinted wiring board ... Pages 4-11 to 4-14 SY-58 board. Electrical parts list ... Page...
Author: Acal1978 Shared: 8/19/19
Downloads: 395 Views: 3268

Content

DSC-S30/S50 SERVICE MANUAL US Model Ver 1.1 2000. 09 Canadian ModelLevel 2 With SUPPLEMENT-1(9-929-819-82) AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model

Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model as well.

On the SY-58 board SY-58 board

This service manual procides the information that is premised the Schematic diagram ... Pages 4-15 to 4-30 circuit board replacement service and not intended repair inside the Ptinted wiring board ... Pages 4-11 to 4-14 SY-58 board. Electrical parts list ... Pages 6-11 to 6-15 Therefore, schematic diagram, printed wiring board and electrical parts list of the SY-58 board are not shown. The above-described information is shown in service manual The following pages are not shown. Level 3.

SPECIFICATIONS

System Output connector Operation temperature Rated output voltage Image device A/V OUT (Monaural) 32˚F to 104˚F DC 8.4 V, 1.5 A in operating 1/2.7 type color CCD (DSC-S50 only) (0˚C to 40˚C) mode Lens Minijack Storage temperature Operation temperature 3 × zoom lens Video: 1 Vp-p, 75 ohms, –4˚F to +140˚F 32˚F to 104˚F (0˚C to 40˚C) f = 6.1 – 18.3 mm unbalanced, sync negative (–20˚C to +60˚C) Storage temperature (39 – 117 mm when converted Audio: 327 mV (at a Maximum dimensions –4˚F to +140˚F into a 35 mm still camera) 47 kilohm load) 4 1/2 ×2 3/4 ×2 3/4 inches (–20˚C to +60˚C) F = 2.8 – 2.9 Output impedance: (113 ×68 ×69 mm) (w/h/d) Maximum dimensions Exposure control 2.2 kilohms Mass 5× 1 9/16 ×2 1/2 inches Automatic exposure VIDEO OUT Approx. 13 oz (370 g) (125 ×39 ×62 mm) (w/h/d) White balance (DSC-S30 only) (including battery pack NP- Mass Automatic, Indoor, Outdoor, Minijack FM50, “Memory Stick”, wrist Approx. 10 oz (280 g) Hold Digital I/O (USB) strap and lens cap etc.) NP-FM50 battery pack Data system Special minijack Built-in microphone Used battery Still: JPEG, GIF (in TEXT LCD screen (DSC-S50 only) Lithium ion battery mode), TIFF Used LCD panel Electret condenser microphone Maximum voltage Movie (DSC-S50 only): 2 type TFT (Thin Film Built-in speaker DC 8.4 V MPEG1 Transistor active matrix) drive (DSC-S50 only) Nominal voltage Audio with still image Total number of dots Dynamic speaker DC 7.2 V (DSC-S50 only): MPEG1 (Monaural) 123 200 (560 ×220) dots AC-L10 AC power Capacity adaptor 8.5 Wh (1 180mAh)Recording medium General “Memory Stick” Power requirements Design and specifications are Used battery pack Flash 100 to 240 V AC, 50/60 Hz subject to change without NP-FM50 Recommended recording notice.Power requirements distance: 8.4 V 11 7/8 inches to 8 1/4 feet (0.3 m to 2.5 m) Power consumption (during recording) 2.9 W DIGITAL STILL CAMERA, Supplied accessories 1 AC-L10 AC power adaptor12342Power cord (1) 3 A/V connecting cable (DSC-S50) (1) 4 NP-FM50 Battery pack (1) 56785Wrist strap (1) 6 Lens cap strap (1) 7 Memory Stick (4MB) (1) 8 Lens cap (1) 9 0 qa qs 9 Bundle soft (2000) (1) (Compact Disk) 0 USB cable (1) qa 2-pin conversion adaptor (1) E model qd qs 2-pin conversion adaptor (1) Tourist model qd VIDEO connecting cable (DSC-S30) (1) SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED À LA SÉCURITÉ! LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 AND IN THE PARTS LIST ARE CRITICAL TO SAFE SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE OPERATION. REPLACE THESE COMPONENTS WITH DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ SONY PARTS WHOSE PART NUMBERS APPEAR AS DE FONCTIONNEMENT. NE REMPLACER CES COM- SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- POSANTS QUE PAR DES PIÈCES SONY DONT LES LISHED BY SONY. NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-sol- 4. Look for parts which, though functioning, show obvious signs dered connections. Check the entire board surface for solder of deterioration. Point them out to the customer and recom- splashes and bridges. mend their replacement. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. “pinched” or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, particularly transis- • Keep the temperature of the soldering iron around 270 ˚C tors, that were installed during a previous repair. Point them during repairing. out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when sol- dering or unsoldering. – 2 –,

TABLE OF CONTENTS

Section Title Page Section Title Page SERVICE NOTE ... 5 • JK-194 (USB, A/V out), KJ-11 (Panel Reverse), SW-339 (Switch) Schematic Diagrams ... 4-39 1. GENERAL • DD-141 (DC/DC Converter, Video, USB) Printed Wiring Board ... 4-41 Identifying the Parts ... 1-1 • DD-141 (DC/DC Converter) Preparing the Power Supply ... 1-2 Schematic Diagram ... 4-43 Setting the Date and Time ... 1-3 • DD-141 (Video) Inserting the “Memory Stick” ... 1-4 Schematic Diagram ... 4-45 Recording Still Images ... 1-4 • DD-141 (USB) Recording Moving Images (DSC-C50 only) ... 1-5 Schematic Diagram ... 4-47 Playing Back Still Images ... 1-5 4-3. Waveforms ... 4-49 Playing Back Moving Images ... 1-5 4-4. Parts Location ... 4-51 Viewing Images Using a Personal Computer ... 1-6 Image File Storage Destinations and Image Files ... 1-7 5. ADJUSTMENTS Before Performing Advanced Operations ... 1-7 Various Recording ... 1-9 Before Starting Adjustment ... 5-1 Various Playback ... 1-11 1-1. Adjusting Items when Replacing Editing ... 1-12 Main Parts and Boards... 5-2 Precautions ... 1-13 5-1. Camera Section Adjustment ... 5-3 On “Memory Sticks” ... 1-14 1-1. Preparations Before Adjustment ... 5-3 Using Your Camera Abroad ... 1-14 1-1-1. List of Service Tools ... 5-3 Troubleshooting ... 1-14 1-1-2. Preparations ... 5-4 Warning and Notice Messages ... 1-15 1-1-3. Discharging of the Flashlight Power Supply ... 5-4 Self-diagnosis Display ... 1-15 1-1-4. Precautions ... 5-6 LCD Screen Indicators ... 1-16 1. Setting the Switch ... 5-6 2. Order of Adjustments ... 5-6 2. DISASSEMBLY 3. Subjects ... 5-6 4. Preparing the Flash Adjustment Box ... 5-7 1-2. Initialization of B, D, E, F, 7 Page Data ... 5-8 • Attachment of CPC-9 Jig ... 2-1 1-2-1. Initialization of D Page Data ... 5-8 2-1. PD-127 Board and Indicator Module ... 2-2 1. Initializing the D Page Data ... 5-8 • Service Position (LCD Panel and PD-127 Board) ... 2-2 2. Modification of D Page Data ... 5-8 2-2. Front Cabinet Block Assembly ... 2-3 3. D Page Table ... 5-8 2-3. Battery Lid Assembly and Control Switch Block ... 2-3 1-2-2. Initialization of B, E, F, 7 Page Data ... 5-9 2-4. Flash Unit and Upper Cabinet Block ... 2-4 1. Initializing the B, E, F, 7 Page Data ... 5-9 2-5. MS-50 Board and BT Holder Assembly ... 2-4 2. Modification of B, E, F, 7 Page Data ... 5-9 2-6. Lens Block Assembly ... 2-5 3. B Page Table ... 5-9 2-7. SY-58 Board, DD-141 Board 4. E Page Table ... 5-9 and JK-194 Board ... 2-5 5. F Page Table ... 5-10 2-8. Control Switch Block and SW-339 Board ... 2-6 6. 7 Page Table ... 5-11 • Overall Check Service Position ... 2-6 1-3. Video System Adjustments ... 5-12 2-9. Hinge Assembly and KJ-11 Board ... 2-7 1. Video Sync Level Adjustment ... 5-12 2-10. Circuit Boards Location ... 2-8 2. Video Burst Level Adjustment ... 5-12 2-11. Flexible Boards Location ... 2-8 1-4. Camera System Adjustment ... 5-13 1. HALL Adjustment ... 5-13 3. BLOCK DIAGRAMS 2. Flange Back Adjustment (Using the minipattern box) ... 5-14 3-1. Overall Block Diagram ... 3-1 3. Flange Back Check ... 5-15 3-8. Power Block Diagram 1 ... 3-15 4. F No. Standard Data Input ... 5-16 3-9. Power Block Diagram 2 ... 3-17 5. Mechanical Shutter Adjustment ... 5-16 6. Picture Frame Setting ... 5-17 4. PRINTED WIRING BOARDS AND 7. Light Level Adjustment ... 5-18 SCHEMATIC DIAGRAMS 8. Mixed Color Cancel Adjustment ... 5-18 9. Auto White Balance Standard Data Input ... 5-19 4-1. Frame Schematic Diagram (1/2) ... 4-3 10. Auto White Balance Adjustment ... 5-19 Frame Schematic Diagram (2/2) ... 4-5 11. Color Reproduction Adjustment ... 5-20 4-2. Printed Wiring Boards and Schematic Diagram ... 4-7 12. Color Reproduction Check ... 5-21 • CD-262 (CCD Imager) 13. White Balance Check ... 5-22 Printed Wiring Board ... 4-7 14. Strobe White Balance Adjustment ... 5-23 • CD-262 (CCD Imager) 15. Strobe Light Level and White Balance Check ... 5-23 Schematic Diagram ... 4-8 16. CCD Black Defect Compensation ... 5-24 • MS-50 (FU, Memory Stick) 17. CCD White Defect Compensation ... 5-24 Printed Wiring Board ... 4-9 1-5. LCD System Adjustments ... 5-25 • MS-50 (FU, Memory Stick) 1. LCD Initial Data Input ... 5-26 Schematic Diagram ... 4-10 2. VCO Adjustment (PD-127 Board) ... 5-26 • PD-127 (TG, LCD) 3. D Range Adjustment (PD-127 Board) ... 5-27 Printed Wiring Board ... 4-31 4. Bright Adjustment (PD-127 Board) ... 5-27 • PD-127 (LCD Drive) 5. Contrast Adjustment (PD-127 Board) ... 5-28 Schematic Diagram ... 4-33 6. Color Adjustment (PD-127 Board) ... 5-28 • PD-127 (Timing Generator) 7. V-COM Level Adjustment (PD-127 Board) ... 5-29 Schematic Diagram ... 4-35 8. V-COM Adjustment (PD-127 Board) ... 5-29 • JK-194 (USB, A/V out), KJ-11 (Panel Reverse), 9. White Balance Adjustment (PD-127 Board) ... 5-30 SW-339 (Switch) Printed Wiring Boards ... 4-37 – 3 –, Section Title Page 1-6. System Control System Adjustments ... 5-31 1. Battery Down Adjustment ... 5-31 5-2. Service Mode ... 5-32 2-1. Adjusting Remote Commander ... 5-32 1. Used Adjusting Remote Commander ... 5-32 2. Precautions upon Using the Adjusting Remote Commander ... 5-32 2-2. Data Process ... 5-33 2-3. Service Mode ... 5-34 1. Setting the Test Mode ... 5-34 2. Bit Value Discrimination ... 5-34 3. Switch Check (1) ... 5-34 4. Switch Check (2) ... 5-35 5. LED Check ... 5-35 6. LCD Check ... 5-35 6. REPAIR PARTS LIST 6-1. Exploded Views ... 6-1 6-1-1. Front Panel Section ... 6-1 6-1-2. Main Section ... 6-2 6-1-3. Rear Cabinet Section ... 6-3 6-1-4. Lens Block Assembly ... 6-4 6-2. Electrical Parts List ... 6-5 * The color reproduction frame is shown on page 117. – 4 –,

SERVICE NOTE

• NOTE FOR REPAIR When remove a connector, don’t pull at wire of connector. Be in danger of the snapping of a wire. Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector. Be in danger of the snapping of a wire. Cut and remove the part of gilt which comes off at the point. (Take care that there are some pieces of gilt left inside) [Discharging of the FLASH unit’s charging capacitor] Discharging the Capacitor Short-circuit between the positive and the negative terminals of The charging capacitor of the FLASH unit is charged up to the charged capacitor with the short jig about 10 seconds. maximum 300 V potential. There is a danger of electric shock by this high voltage when the battery is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the MVC-FD71 is simply turned off. Therefore, the re- maining voltage must be discharged as described below. R: 1 kΩ/1 W (Part code: Preparing the Short Jig Capacitor 1-215-869-11) To preparing the short jig. a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to pre- vent electrical shock. 1 kΩ/1 W Wrap insulating tape. – 5 –, [Description on Self-diagnosis Display] Self-diagnosis display • C: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom *1 initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. *2 Note: The error code is cleared if the battery is removed, except defective flash, unit. *1: The error display is given in two ways. *2: When the flash charging failed, Page : D, Address: 67. Data: 04 are written. After repair, be sure to write Page: D, address: 67. Data: 00. – 6 –,

DSC-S30/S50

1. GENERAL This section is extracted from DSC-S30/S50 instruction manual. CAUTION Note: Caution:

WARNING You are cautioned that any changes or This equipment has been tested and found to Do not handle damaged or leaking lithium

modifications not expressly approved in this To prevent fire or shock hazard, do comply with the limits for a Class B digital ion battery. manual could void your authority to operate device, pursuant to Part 15 of the FCC not expose the unit to rain or this equipment. Rules. These limits are designed to provide moisture. reasonable protection against harmful For the Customers in Canada

Declaration of Conformity interference in a residential installation. This

equipment generates, uses, and can radiate CAUTION

For the Customers in the Trade Name: SONY radio frequency energy and, if not installed TO PREVENT ELECTRIC SHOCK, DO U.S.A. Model No.: DSC-S30 and used in accordance with the NOT USE THIS POLARIZED AC PLUG

Responsible Party:Sony Electronics Inc. instructions, may cause harmful interference WITH AN EXTENSION CORD, Address: 1 Sony Drive, Park to radio communications. However, there is RECEPTACLE OR OTHER OUTLET Ridge, NJ 07656 no guarantee that interference will not occur UNLESS THE BLADES CAN BE FULLY USA in a particular installation. If this equipment INSERTED TO PREVENT BLADE Telephone No.: 201-930-6972 does cause harmful interference to radio or EXPOSURE. television reception, which can be This device complies with Part 15 of the determined by turning the equipment off and FCC Rules. Operation is subject to the on, the user is encouraged to try to correct NOTICE FOR THE following two conditions: (1) This the interference by one or more of the CUSTOMERS IN THE UNITED device may not cause harmful following measures: KINGDOM interference, and (2) this device must — Reorient or relocate the receiving accept any interference received, antenna. A moulded plug complying with BS 1363 is including interference that may cause — Increase the separation between the fitted to this equipment for your safety and undesired operation. equipment and receiver. convenience. This symbol is intended to alert the user to the presence — Connect the equipment into an outlet of uninsulated “dangerous on a circuit different from that to which Should the fuse in the plug supplied need to

Declaration of Conformity the receiver is connected. be replaced, a 5 AMP fuse approved by voltage” within the

product’s enclosure that Trade Name: SONY — Consult the dealer or an experienced ASTA or BSI to BS 1362, (i.e. marked with or mark) must be used. may be of sufficient Model No.: DSC-S50 radio/TV technician for help. magnitude to constitute a Responsible Party:Sony Electronics Inc. The shielded interface cable recommended Address: 1 Sony Drive, Park in this manual must be used with this If the plug supplied with this equipment has risk of electric shock to persons. Ridge, NJ 07656 equipment in order to comply with the limits a detachable fuse cover, be sure to attach the USA for a digital device pursuant to Subpart B of fuse cover after you change the fuse. Never Telephone No.: 201-930-6972 Part 15 of FCC Rules. use the plug without the fuse cover. If you This symbol is intended to should lose the fuse cover, please contact alert the user to the presence of important operating and This device complies with Part 15 of the DISPOSAL OF LITHIUM ION your nearest Sony service station. maintenance (servicing) FCC Rules. Operation is subject to the BATTERY. instructions in the literature following two conditions: (1) This LITHIUM ION BATTERY. For the Customers in accompanying the device may not cause harmful appliance. interference, and (2) this device must DISPOSE OF PROPERLY. Germany accept any interference received, Never expose the battery pack to You can return your unwanted lithium ion Directive:EMC Directive 89/336/EEC.92/including interference that may cause temperature above 140˚F (60˚C), such as in batteries to your nearest Sony Service 31/EEC undesired operation. a car parked in the sun or under direct Center or Factory Service Center. This equipment complies with the EMC sunlight. regulations when used under the following Note: circumstances: In some areas the disposal of lithium ion If you have any questions about this • Residential area batteries in household or business trash may product, you may call: • Business district be prohibited. Sony Customer Information Center • Light-industry district 1-800-222-SONY (7669) (This equipment complies with the EMC For the Sony Service Center nearest you call or write to: standard regulations EN55022 Class B.) 1-800-222-SONY (United States only) Sony Customer Information Center For the Sony Factory Service Center nearest 1 Sony Drive, Mail Drop #T1-11, Park you call 416-499-SONY (Canada only) Ridge, NJ 0765623Getting started

Attention Notes on image data compatibility • This camera conforms with the Design Identifying the parts

The electromagnetic fields at the specific Rules for Camera File Systems universal frequencies may influence the picture and standard established by the JEIDA (Japan sound of this camera. Electronic Industries Development See the pages in parentheses for details of operation. Association). You cannot play back on your camera still images recorded on other15“Memory Stick” equipment (DCR-TRV890/TRV900/ 6 TRV900E, DSC-D700, DSC-D770) that 2 does not conform with this universal 7 standard. (These models are not sold in38some areas.)

N50 • Playback of images recorded with your camera on other equipment and playback

of images recorded or edited with other equipment on your camera are not guaranteed. 9

For the Customers in CANADA

Precaution on copyright This Class B digital apparatus complies with Television programs, films, video tapes, and Canadian ICES-003. 0 qaother materials may be copyrighted. Unauthorized recording of such materials

For the Customers in the may be contrary to the provision of the U.S.A. copyright laws. 4 qs

This device complies with Part 15 of the Do not shake or strike the camera FCC Rules. Operation is subject to the In addition to malfunctions and inability to A Flash (19) I Lens following two conditions: (1) This device record images, this may render the may not cause harmful interference, and “Memory Stick” unusable or image data B MODE selector (29) J A/V OUT jack (DSC-S50 only) (2) this device must accept any interference breakdown, damage or loss may occur. (48) received, including interference that may C Shutter button (16) (20) cause undesired operation. LCD screen and lens Audio output is monaural. • The LCD screen is manufactured using D Lens cap VIDEO OUT jack (DSC-S30 high-precision technology. However, there only) (48)

Be sure to read the following E Photocell window for flash may be some tiny black points and/or

before using your camera bright points (red, blue or green in color) Do not block while recording. K USB jack (25) (26) that constantly appear on the LCD screen. • This Owner's Manual is for the two These points are normal in the F Self-timer/recording lamp L Tripod receptacle (bottom models of the DSC-S30 and the manufacturing process and do not affect surface) DSC-S50. Check to make sure which G Built-in microphone (DSC-S50 the recording in any way. Over 99.99% of Use a tripod with a screw length of model you have purchased before only)the pixels are operational for effective use. less than 9/32 inch (6.5 mm). You you use your camera. • Be careful when placing the camera near a Do not touch while recording. will be unable to firmly secure the • The illustrations in this manual window or outdoors. Exposing the LCD show the DSC-S50. H Speaker (DSC-S50 only) camera to tripods having longer screen or the lens to direct sunlight for screws, and may damage the long periods may cause malfunctions. Trial recording camera. Before you record one-time events, you may Do not get the camera wet want to make a trial recording to make sure When taking pictures outdoors in the rain or that the camera is working correctly. under similar conditions, be careful not to get the camera wet. If moisture No compensation for contents of condensation occurs, refer to page 54 and the recording follow the instructions on how to remove it Contents of the recording cannot be before using the camera. compensated for if recording or playback is not possible due to a malfunction of your Back up recommendation camera, etc. To avoid the potential risk of data loss, always copy (back up) data to a disk. 4 6 1-1, Attaching the strap Preparing the power supply

Installing the battery pack

Your camera operates only with the “InfoLITHIUM” NP-FM50 battery pack* (M 1 series). You cannot use any other battery pack. 290qa qf 5 qs qg 6 qd 7 qh 8 qj Battery eject lever A Flash button G DISPLAY button B FOCUS button (41) H LCD screen 1 Open the battery/“Memory Stick” cover. C LCD BACKLIGHT BRIGHT/ I Hook for lens cap/strap Open the cover while sliding the OPEN switch in the direction of the arrow. NORMAL switch J Zoom button Usually set to NORMAL. When 2 Install the battery pack. you use the camera outdoors or in K Access lamp (15) Insert the battery pack with the B mark facing tow ard the battery compartment other bright places, setting this to as illustrated. BRIGHT makes the LCD screen L Battery/“Memory Stick” cover bright and easy to see, but also M Battery eject lever (8) 3 Close the battery/“Memory Stick” cover. uses up the battery faster. N OPEN switch D Control button O POWER switch To remove the battery pack E PROGRAM AE +/– button Open the battery/“Memory Stick” cover. Slide the battery eject lever VOLUME +/– button P DC IN jack (9) (12) downward, and remove the battery pack. Q POWER lamp/BATT CHARGE Be careful not to drop the battery pack when removing it. F PROGRAM AE button (42) lamp (9) (13) * What is “InfoLITHIUM”? “InfoLITHIUM” is a lithium ion battery pack which can exchange information such as battery consumption with compatible video equipment. This unit is compatible with the “InfoLITHIUM” battery pack (M series). “InfoLITHIUM” M series battery packs have the mark. “InfoLITHIUM” is a trademark of Sony Corporation. 7 8

Charging the battery pack Charging time

You cannot charge the battery pack while your camera is turned on. Be sure to turn Battery pack Full charge (min.) Normal charge (min.) off your camera before charging. NP-FM50 (supplied) 150 90 Approximate time to charge a completely discharged battery pack using the A BATT CHARGE lamp AC power adaptor. Battery pack (M series) To the wall outlet (mains) Battery life and number of images that can be recorded/played back STILL mode recording* Power cord DC IN jack cover (mains lead) DSC-S50 LCD BACKLIGHT Battery life (min.) Number of images BRIGHT 140 (130) 2300 (2100) NORMAL 150 (140) 2500 (2300) AC-L10 DSC-S30 AC power adaptor LCD BACKLIGHT Battery life (min.) Number of images BRIGHT 140 (130) 2800 (2600) 1 Insert the battery pack into your camera. NORMAL 150 (140) 3000 (2800) STILL mode playback** (DSC-S50/S30) 2 Open the DC IN jack cover and connect the DC connecting cable to the DC IN jack of your camera with the v mark facing up. LCD BACKLIGHT BaCtte-Lry1 0li fe (min.) Number of images BRIGHT 170 (160) 3400 (3200) 3 Connect the power cord (mains lead) to the AC power adaptor and then to a wall outlet (mains). NORMAL 220 (210) 4400 (4200) The BATT CHARGE lamp lights orange when charging begins. When the Approximate battery life and number of images that can be recorded/played back BATT CHARGE lamp goes off, normal charge is completed. For full with a fully charged battery pack at a temperature of 77˚F (25˚C), 640×480 image charge, which allows you to use the battery longer than usual, leave the size and in NORMAL recording mode. Numbers in parentheses indicate the time battery pack inserted for about one hour after normal charge is completed. when you use a normally charged battery pack. ∗ Recording at about 5-second intervals Battery remaining indicator ∗∗ Playing back single images in order at about 3-second intervals The LCD screen on the camera shows the remaining time for which you can still record or play back images. MOVIE mode recording (DSC-S50 only) This indication may not be entirely accurate depending on the conditions of use and the operating environment. LCD BACKLIGHT Battery life (min.) BRIGHT 140 (130) Auto power-off function NORMAL 150 (140) If you do not operate the camera for about three minutes during recording, the camera turns off automatically to prevent wearing down the battery. To use the Approximate time that can be recorded with a fully charged battery pack at a camera again, slide down the POWER switch to turn on the camera again. temperature of 77˚F (25˚C) and 160×112 image size. Numbers in parentheses indicate the time when you use a normally charged battery pack. 9 10 1-2

Getting started Getting started

, Notes • The battery life and number of images will be decreased if you use your camera at low Using the AC power adaptor temperatures, use the flash, repeatedly turn the power on/off or use the zoom. • The capacity of the “Memory Stick” is limited. The above figures are a guide when you continuously record/play back while replacing the “Memory Stick.” • If sufficient battery remaining time is indicated but the power runs out soon, fully charge the battery so that the correct battery remaining time appears. • Do not short the DC plug of the AC power adaptor with a metallic object, as this may cause malfunction. To the wall outlet (mains) • Do not expose the battery pack to water. DC IN jack cover Power cord (mains lead) AC-L10 AC power adaptor 1 Open the DC IN jack cover and connect the DC connecting cable to the DC IN jack of your camera with the v mark facing up. 2 Connect the power cord (mains lead) to the AC power adaptor and then to a wall outlet (mains). Using a car battery Use Sony DC adaptor/charger. 11 12

Setting the date and time 5 Select the desired date display format with

v/V on the control button, then press the When you first use your camera, set the date and time. If these are not set, the center z. CLOCK SET screen appears whenever you turn on your camera for recording. Select from Y/M/D (year/month/day), M/D/Y (month/day/year) or D/M/Y (day/month/year). 6 Select the year, month, day, hour or minute Control button item you want to set with b/B on the control button. The item to be set is indicated with v/V.

POWER

lamp 7 Set the numeric value with v/V on the control button, then press the center z to enter it. After entering the number, v/V moves to the next item. If you selected [D/M/Y] in step 5, set the time on a 24-hour cycle. 1 Slide down the POWER switch to turn on the power. 8 Select [ENTER] with B on the control The POWER lamp lights up. button, then press the center z at the desired moment to begin clock movement. 2 Press v on the control button. The date and time are entered. The menu bar appears on the LCD screen. To cancel the date and time setting Select [CANCEL] with v/V/b/B on the control button, then press the center z. 3 Select [SETUP] with B on the control button, then press the center z. 4 Select [CLOCK SET] with v/V on the control button, then press the center z. 13 14 1-3

Getting started Getting started

,

Basic operations B Recording Inserting the “Memory Stick” Recording still images

Still images are recorded in JPEG format. To record still images, slide the POWER switch down to turn on the power and insert a “Memory Stick.” Access lamp POWER switch 1 Open the battery/“Memory Stick” cover. Open the cover while sliding the OPEN switch in the direction of the arrow. 2 Insert the “Memory Stick.” Set the MODE selector to STILL. Insert the “Memory Stick” with the B mark facing toward the battery 1 compartment as illustrated until it clicks. 2 Press and hold the shutter button halfway Remaining memory 3 Close the battery/“Memory Stick” cover. down and check the image. utton. capacity indicator While the AE lock indicator z (green) is flashing, the image freezes momentarily, but is not yet ention switch is set to Removing the “Memory Stick” recorded. When the camera finishes the automatic adjustments*, the AE lock indicator z lights up Open the battery/“Memory Stick” cover, then press the “Memory Stick” once lightly. and the camera is ready for recording. To cancel the recording, release the shutter b Notes • Insert the “Memory Stick” firmly until it clicks, otherwise a message such as “MEMORY STICK ERROR” will be displayed. AE lock indicator • Never remove the “Memory Stick” or turn off the power while the access lamp is lit up. • You cannot record or edit images on a “Memory Stick” if the erasure prev the LOCK position. 3 Press the shutter button fully down. Connector The shutter sounds and the image is recorded on the “Memory Stick.” When “REC” disappears, you can record the next image. Erasure prevention switch LOCK ∗ Exposure and focus are automatically adjusted. The number of images you can record on a “Memory Stick” See pages 37 to 40. Note While the image is being recorded on the “Memory Stick,” do not shake or strike the camera. Label space Also, do not turn the power off, or remove the battery pack or “Memory Stick.” 15 16 Checking the last recorded image (Quick Review) LCD screen indicators during recording You can check the last recorded image by clearing the menu bar from the screen Press DISPLAY to turn on/off the indicators on the LCD screen. (page 31) and pressing b on the control button. To return to the normal recording See page 64 for a detailed description of the indicated items. mode, press lightly on the shutter button or select [RETURN] with b/B on the control button and then press the center z. You can also delete the image first by selecting [DELETE] on the Quick Review screen with b/B on the control button and pressing the center z, and then selecting [OK] with v/V on the control button and pressing the center z.

DISPLAY

Using the zoom feature Zoom button Notes W side: for wide-angle (subject appears • You cannot turn off the self-timer indicators and some of the indicators used in advanced farther away) operations. • The indicators on the LCD screen are not recorded.

Using the self-timer

T side: for telephoto (subject appears closer) When you use the self-timer function, the subject is recorded about 10 seconds after you press the shutter button. Minimum focal distance to the subject Shutter button W side: About 9 7/8 inches (25 cm) or more T side: About 23 5/8 inches (60 cm) or more Self-timer lamp To record even closer subjects, see page 41. Digital zoom function Control button This camera has a digital zoom function. Digital zoom enlarges the image by digital processing and it starts to function when zoom exceeds 3×. Select (self-timer) indicator on the LCD screen with v/V/b/B on the control button, then press the center z. The (self-timer) indicator appears on the LCD screen, and about 10 seconds after you press the shutter button, the subject is The T side of the bar shows the recorded. The self-timer lamp flashes after you press the shutter button until the digital zooming zone. shutter is released. Using digital zoom • The maximum zoom magnification is 6×. • Digital zooming deteriorates the picture quality. When digital zoom is not necessary, set [DIGITAL ZOOM] to [OFF] in the menu settings (page 34). Note Digital zoom does not work for moving images. 17 18 1-4

Getting started B Recording

,

Recording images with the flash Recording moving images (DSC-S50 only)

The initial setting is auto (no indicator). In this mode, the flash automatically strobes Moving images with audio are recorded in MPEG format. when the surroundings become dark. When you change the flash mode, press the To record moving images, slide the POWER switch down to turn on the power and (flash) repeatedly so that the flash mode indicator appears on the LCD screen. insert a “Memory Stick.” (flash)

DISPLAY

POWER switch Each time you press the (flash), the indicator changes as follows. (No indicator) tttt(No indicator) Auto red-eye reduction: The flash strobes before recording to reduce the red-eye phenomenon. Forced flash: The flash strobes regardless of the surrounding brightness. 1 Set the MODE selector to MOVIE. No flash: The flash does not strobe. You can change the brightness of the flash (FLASH LEVEL) in the menu settings 2 Press the shutter button fully down. (page 34). “REC” appears on the LCD screen, and the image and sound are recorded on Notes the “Memory Stick.” • The recommended shooting distance using the built-in flash is 31/32 feet to 8 1/3 feet (0.3 m to If you press the shutter button momentarily 2.5 m). The image and sound are recorded for five seconds. You can change the • Attaching a conversion lens (not supplied) may block the light from the flash or cause the lens recording time to 10 or 15 seconds with [REC TIME SET] in the menu settings shadow to appear. • (page 33).Auto red-eye reduction may not produce the desired red-eye reduction effects depending on individual differences, the distance to the subject, if the subject does not see the pre-strobe, or If you hold the shutter button down other conditions. In addition, red-eye reduction effects are also difficult to obtain if you set the The image and sound are recorded while the shutter button is held down for up shutter to a slow speed in the PROGRAM AE shutter priority mode. • to 60 seconds. However, when [IMAGE SIZE] in the menu setting is set to The flash effect is not obtained easily when you use forced flash in a bright location. [320×240], the maximum recording time is 15 seconds (page 33). Zooming or using the self-timer, etc. See pages 17 and 18. LCD screen indicators during recording Press DISPLAY to turn on/off the indicators on the LCD screen. These indicators are not recorded. See page 64 for a detailed description of the indicators. 19 20 B Playback

Playing back still images Playing back moving images

VOLUME +/– DISPLAY POWER switch POWER switch

DISPLAY

1 Set the MODE selector to PLAY. 1 Set the MODE selector to PLAY. The last recorded image (still or moving) appears on the LCD screen. The last recorded image (still or moving) appears on the LCD screen. 2 Press v on the control button to display the menu bar on the LCD 2 Press v on the control button to display the menu bar on the LCD screen. screen. 3 Select the desired moving image with the 3 Select the desired still image with the control button. control button. Moving images are displayed one-size smaller than Press v/V/b/B on the control button to select "b/B" still images. on the LCD screen, then press b/B on the control Press v/V/b/B on the control button to select "b/B" button. on the LCD screen, then press b/B on the control "b: To display the preceding image. button. B": To display the next image. "b: To display the preceding image. B": To display the next image. 4 Select B (playback) on the LCD screen with B (playback)/X When the menu bar is not displayed v/V/b/B on the control button, then press You can directly select and play back the image with b/B on the control button. the center z. The moving image and sound* are played back. Notes During playback, B (playback) changes to X • You might not be able to correctly play back images recorded with this camera on other (pause). equipment. ∗ You can play back sound in DSC-S50 only. • You cannot play back on this camera images larger than the maximum image size that can be recorded with this camera. Playback bar

LCD screen indicators during still image playback

Press DISPLAY to turn on/off the indicators on the LCD screen. To pause playback See page 64 for a detailed description of the indicators. Select X (pause) on the LCD screen with v/V/b/B on the control button, then press the center z. 21 22 1-5

B Recording B Playback

, When the menu bar is not displayed You can directly select the image with b/B on the control button, and play back the Viewing images using a personal computer image and sound (DSC-S50 only) by pressing the center z. When you press the center z during playback, playback is paused. You can view data recorded with your camera on a personal computer and attach it to e-mail. This section describes the method for installing the USB driver and viewing Adjusting the volume (DSC-S50 only) images on a personal computer. Be sure to also see the operation manuals for your personal computer and application software. Press VOLUME +/– to adjust the volume. Note Data recorded with your camera is stored in the following formats. Make sure that applications

LCD screen indicators during moving image playback that support these file formats are installed on your personal computer.

• Still images (other than TEXT and uncompressed modes): JPEG format Press DISPLAY to turn on/off the indicators on the LCD screen. • Moving images/audio: MPEG format See page 64 for a detailed description of the indicators. • Uncompressed mode still images: TIFF format • TEXT mode: GIF format

Recommended computer environment

Recommended Windows environment OS: Microsoft Windows 98, Windows 98SE Standard installation is required. Operation is not assured in an environment upgraded from: Windows 3.1, Windows 95 to Windows 98 or Windows 98 to Windows 98SE. CPU: MMX Pentium 200 MHz or faster The USB connector must be provided as standard. ActiveMovie Player (DirectShow) must be installed (to play back moving pictures). Recommended Macintosh environment Macintosh computer with the Mac OS 8.5.1/8.6/9.0 standard installation However, note that the update to Mac OS 9.0 should be used for the following models. • iMac with the Mac OS 8.6 standard installation and a slot loading type CD-ROM drive • iBook or G4 with the Mac OS 8.6 standard installation The USB connector must be provided as standard. QuickTime 3.2 or newer must be installed (to play back moving pictures). Notes • Operations are not guaranteed for either the Windows or Macintosh environment if you connect two or more USB equipment to a single personal computer at the same time (except for the USB keyboard and mouse which are provided as standard), or when using a hub. • Depending on the type of USB equipment that is used simultaneously, some equipment may not operate. • Operations are not guaranteed for all the recommended computer environments mentioned above.

Installing the USB driver 3 Double-click the CD-ROM drive icon to open the window.

Before connecting your camera to your personal computer, install the USB driver to the computer. The USB driver is contained together with application software for 4 Double-click the icon of the hard disk containing the OS to open viewing images on a CD-ROM which is supplied with your camera. the window. For Windows 98 users 5 Move the following two driver files from the window opened in step 3 to the “System Folder” icon in the window opened in step41Turn on your personal computer and allow Windows 98 to load. (drag and drop). • Sony USB Driver Insert the supplied CD-ROM in the CD-ROM drive of your personal • Sony USB Shim2 computer. 6 When “Put these items into the Extensions folder?” appears, click 3 Connect the USB jack on your camera with the USB connector on “OK.” your personal computer using the supplied USB cable. 7 Restart your personal computer. to the USB connector to the USB jack Viewing images Push in until the For Windows 98 users USB cable connector clicks Personal computer 1 Turn on the power of your personal computer and allow into place Windows 98 to load. 2 Connect one end of the USB cable to the USB jack on the camera 4 Insert a “Memory Stick” into your camera, connect the AC power and the other end to the USB connector on your personal adaptor and turn on your camera. computer. “PC MODE” appears on the LCD screen of your camera and the camera is set to communication standby mode. Your personal computer recognizes the camera, and the Windows 98 Add Hardware Wizard starts. to the USB connector to the USB jack 5 Follow the on-screen messages to specify the CD-ROM drive and install the USB driver. The Add Hardware Wizard starts twice because two different USB drivers are Push in until the installed. Be sure to allow the installation to complete without interrupting it. USB cable connector clicks Personal computer into place Note Insert a “Memory Stick” into your camera, and connect the AC Be sure to insert a “Memory Stick” into your camera before installing the USB driver. 3 power adaptor to your camera and then to a wall outlet (mains). Otherwise, you will be unable to install the USB driver. 4 Turn on the power of your camera. For Macintosh users “PC MODE” appears on the LCD screen of the camera. 1 Turn on your personal computer and allow the Mac OS to load. 5 Open “My Computer” on Windows 98 and double click the newly recognized drive. (Example: “Removable Disk (D:)”) 2 Insert the supplied CD-ROM in the CD-ROM drive of your personal The folders inside the “Memory Stick” are displayed. computer. 25 26 1-6

Playback B PlaybackB

, 6 Select and double-click the desired image/sound file from the Image file storage destinations and image folder. For the detailed folder and file name, see “Image file storage destinations and files image files” (page 28). Image files recorded with your camera are grouped in folders by recording mode. Desired file type Double-click in this order The meanings of the file names are as follows. ssss stands for any number Still image “Dcim” folder “100msdcf” folder Image file within the range from 0001 to 9999.t t Moving image* “Mssony” folder t “Moml0001” folder t Image file* For Windows 98 users (The drive recognizing the camera is “D.”) Audio* “Mssony” folder t “Momlv100” folder t Audio file* E-mail image “Mssony” folder t “Imcif100” folder t Image file TIFF image Folder containing still image data (uncompressed) ∗ Folder containing E-MAIL mode and TIFF Copying a file to the hard disk of your personal computer before viewing it is recommended. If you play back the file directly from the “Memory Stick”, the image mode image data and sound may break off. Folder containing moving image data Folder containing VOICE mode audio data

Notes on using your personal computer

“Memory Stick” Folder File Meaning • “Memory Stick” operations on your camera cannot be assured if the “Memory Stick” has been 100msdcf DSC0ssss.JPG • Still image file recorded normally formatted on your personal computer. • Still image file recorded in E-MAIL • Do not optimize the “Memory Stick” on a Windows machine. This will shorten the “Memory mode (page 38) Stick” life. • Do not compress the data on the “Memory Stick.” Compressed files cannot be played back on • Still image file recorded in TIFF mode your camera. (page 40) • Still image file recorded in VOICE Software mode (page 39) • Depending on your application software, the file size may increase when you open a still image TXT0ssss.GIF • Still image file recorded in TEXT mode file. (page 39) • When you load an image modified using the supplied retouch software from your personal computer to the camera or when you directly modify the image on the camera, the image Imcif100 DSC0ssss.JPG • Small-size image file recorded in E- format will differ so the “FILE ERROR” message may appear and you may be unable to open MAIL mode (page 38) the file. DSC0ssss.TIF • Uncompressed image file recorded in TIFF mode (page 40) Communications with your personal computer Communications between your camera and your personal computer may not recover after Moml0001 MOV0ssss.MPG • Moving image file recorded normally recovering from Suspend, Resume, or Sleep. Momlv100 DSC0ssss.MPG • Audio file recorded in VOICE mode (page 39) • Windows and ActiveMovie, DirectShow are either registered trademarks or trademarks of The numerical portions of the following files are the same. Microsoft Corporation in the United States and/or other countries. — A small-size image file recorded in E-MAIL mode and its corresponding image file • Macintosh and Mac OS, QuickTime are trademarks of Apple Computer, Inc. — An uncompressed image file recorded in TIFF mode and its corresponding image file • All other product names mentioned herein may be the trademarks or registered trademarks of — An audio file recorded in VOICE mode and its corresponding image file their respective companies. Furthermore, “™” and “®” are not mentioned in each case in this manual. 27 28

Advanced operations

Turning on/off the operation buttons (menu bar) on the LCD screen

Before performing advanced operations

This section describes the basic control methods that are frequently used for Press v to display the menu bar “Advanced operations”. on the LCD screen.

How to use the MODE selector

Press V to clear the menu bar The MODE selector selects whether you can use your camera to record or to play from the LCD screen. back and edit images. Set the selector as follows before starting to operate your Menu bar camera. Note PPLLAAYY PPLLAAYY STILL STILL You cannot clear the menu bar during INDEX screen display (page 45). STILL STILL

MMOOVVIIEE

DSC-S50 DSC-S30 Selecting items and images on the LCD screen PLAY: To play back or edit images 1 Press v/V/b/B on the STILL: To record still images control button to select the and voice memos item you want to set or the MOVIE: To record moving image you want to display. images The color of the selected item or (DSC-S50 only) the border of the selected image changes from blue to yellow.

How to use the control button 2 Press the center z to enter

the item. The control button is used to select the indicators, images and menus appearing on Repeat steps 1 and 2 to execute the LCD screen of your camera. The operation methods that are frequently used for each function. “Advanced operations” are described below. Select Enter (OK) The “Advanced operations” section of this manual refers to selecting and entering items by the above procedure as “Select [(item name)].” 29 30 1-7

Before performing advanced operations B Playback

,

How to change the menu settings Menu settings

Some of the advanced operations for your camera are executed by selecting menu Menu items that can be modified differ depending on the setting of the MODE items displayed on the LCD screen with the control button. selector. The LCD screen shows only the items you can operate at the moment. Initial settings are indicated with x. MODE selector (SELF TIMER) Records with the self-timer (page 18).

EFFECT

Item Setting Description MODE selector P.EFFECT SOLARIZE Sets the image special effects (page 44). MOVIE B&W STILL

SEPIA

NEG.ART 1 Press v on the control button to display the menu bar. The menu bar appears as follows according to the setting of the MODE xOFF selector. DATE/ DAY&TIME Sets whether to insert the date and time STILL TIME DATE into the image (page 44). MOVIE/STILL PLAY (single mode) PLAY (INDEX mode) xOFF

FILE

Item Setting Description MODE selector FORMAT OK Formats a “Memory Stick.” MOVIE

STILL

2 Select the desired item with v/V/b/B on the CANCEL Cancels formatting of a “Memory control button, then press the center z. Stick.” PLAY The color of the selected item changes from blue to POS. ON Plays back images recorded with the STILL yellow, and when you press the center z, the modes SENSOR camera on its side (vertical images) as that can be set for that item are displayed. horizontal images. This function does not work for images recorded in TEXT mode. 3 Select the desired mode with v/V/b/B on the control button, then press the center . xOFF When this camera may be subject to z vibration such as when you record images from inside a moving car, set this to OFF to prevent improper To clear the menu horizontal/vertical judgement. Press V on the control button until the LCD screen returns to the menu bar display in FILE SERIES Assigns numbers to files in sequence MOVIE step 1. To clear the menu bar, press V again. NUMBER even if the “Memory Stick” is changed. STILL xNORMAL Resets the file numbering each time the “Memory Stick” is changed. 31 32 Item Setting Description MODE Item Setting Description MODE selector selector IMAGE x1600×1200 Selects the image size when recording STILL PROTECT ON Protects images against accidental PLAY SIZE 1600 (3:2) still images (DSC-S50 only). erasure (page 49). 1024×768 xOFF Releases protection of images against 640×480 accidental erasure. 1472×1104 Selects the image size when recording STILL x1280×960 still images (DSC-S30 only). CAMERA 1280 (3:2) 1024×768 Item Setting Description MODE selector 640×480 DIGITAL xON Uses digital zoom. STILL 320×240 Selects the MPEG image size when MOVIE ZOOM x160×112 recording moving images (DSC-S50 OFF Does not use digital zoom. only). SHARPNESS +2 to –2 Adjusts the sharpness of the image. STILL REC MODE TIFF Records a TIFF (uncompressed) file in STILL appears on the LCD screen except addition to the JPEG file. when set to 0. TEXT Records a GIF file in black-and-white. WHITE IN DOOR Sets the white balance (page 43). MOVIE

BALANCE

VOICE Records an audio file (with still image) OUT DOOR STILL in addition to the JPEG file (DSC-S50 HOLD only). xAUTO E-MAIL Records a small-size (320×240) JPEG FLASH HIGH Makes the flash level higher than STILL file in addition to the selected image LEVEL normal. size. xNORMAL Normal setting. xNORMAL Records a JPEG file in the selected LOW Makes the flash level lower than normal. image size. EXPOSURE +2.0 EV to Adjusts the exposure. MOVIE REC TIME 15 SEC Adjusts the recording time for moving MOVIE –2.0 EV STILL SET 10 SEC images (DSC-S50 only). x5 SEC

TOOL

ROTATE Rotates the still image. PLAY (in single — Item Setting Description MODE mode only) selector SLIDE INTERVAL Sets the slide show interval. PLAY COPY OK Copies an image (page 51). PLAY SHOW x3 SEC/5 SEC/10 SEC/30 SEC/1 MIN CANCEL Cancels copying of the image. (in single mode only) REPEAT Repeats the slide show. RESIZE 1600×1200 Changes the recorded still image size PLAY xON/OFF (in single 1024×768 (page 51) (DSC-S50 only). START Starts the slide show. mode only) 640×480 CANCEL Cancels the slide show settings and xCANCEL execution. 1472×1104 Changes the recorded still image size PLAY PRINT ON Marks the still images to be printed PLAY 1280×960 (page 51) (DSC-S30 only). MARK (page 53). 1024×768 640×480 xOFF Unmarks the print mark of the still images. xCANCEL 33 34 1-8

Before performing advanced operations Before performing advanced operations

, SETUP 3 (RETURN)** Item Setting Description MODE Returns to PLAY (single) mode. selector ∗ Displayed only in PLAY (single) mode. DEMO xON/STBY Displayed only when you use the AC MOVIE ∗∗ Displayed only in PLAY (INDEX) mode. OFF power adaptor in MOVIE or STILL STILL mode. When ON is selected, a demonstration will start if you do not operate your camera for about 10 minutes. To stop the demonstration, turn off your camera. Select ON to make the demonstration appear again. VIDEO xNTSC Sets the video output signal to NTSC MOVIE OUT mode (North American countries, Japan, STILL etc.). PLAY PAL Sets the video output signal to PAL mode (European countries, etc.). / xENGLISH Displays the menu items in English. MOVIE LANGUAG /JPN Displays the menu items in Japanese. STILL E PLAY CLOCK Sets the date and time (page 13). MOVIE SET — STILL

PLAY

BEEP SHUTTER Turns off the beep only. (The shutter MOVIE sound is heard when you press the STILL shutter button.) PLAY xON Turns on the beep/shutter sound (when you press the control button/shutter button). OFF Turns off the beep/shutter sound. LCD Adjusts the LCD screen brightness MOVIE BRIGHT using the +/– buttons on the LCD STILL screen. This has no effect on the PLAY recorded images. INDEX* Displays six images at a time (PLAY (INDEX) mode) (page 45).

DELETE

Setting Description MODE selector OK Deletes the displayed image. PLAY CANCEL Cancels deleting of the image. 35 36

B Various recording The number of images or the time Setting the image size that you can record on a “Memory Recording still images for e- Rotating the LCD screen — (IMAGE SIZE) Stick” (4 MB): mail (E-MAIL) Face-to-Face recording Image size Number of images or

1 time* E-MAIL mode records a small-size You can record images with the lens (320×240) image at the same time as a 1600× 120 Approx. 4 facing you. still image. Small-size images are 2,3 0 convenient for e-mail transmission, 1600 (3:2) Approx. 4 etc. 1472×110 Approx. 53243111280×960 Approx. 61 Set the MODE selector to MOVIE or STILL. 1280 (3:2) Approx. 6 2 (MOVIE is for DSC-S50 only) 1024×768 Approx. 10 2 Select [FILE] and then 640×480 Approx. 57 [IMAGE SIZE] from the menu. 320×240 Approx. 42 (15**) sec. 3 Select the desired image 1 Set the MODE selector to 160×112 Approx. 169 (60**) sec. 1 size. STILL. Set the MODE selector to ∗ When [REC MODE] is set to MOVIE or STILL. DSC-S50: 2 Select [FILE], [REC MODE], [NORMAL]. Still image sizes and then [E-MAIL] from the 2 Adjust the angle of the LCD × ∗∗ Numbers in parentheses indicate the 1600 1200, 1600 (3:2), menu. screen. maximum recording time during ° 1024×768, 640 ×480Rotate the LCD screen by 180 for continuous recording. 3 Record the image. Face-to-Face recording. Moving image sizes The number of images that you can 320×240, 160 ×112 When [1600 (3:2)], [1280 (3:2)] is 3 Record the image. record on a “Memory Stick” (4 MB) selected The image appears on the LCD DSC-S30: in E-MAIL mode.The image is recorded in 3:2 size to screen as a mirror image, but the Still image sizes match the printing paper size ratio of Image size Number of images recorded image is the same as the 1472×1104, 1280 ×960, 1280 3:2. actual subject. (3:2), 1024 ×768, 640 ×480 1600×1200 Approx. 3 1600 (3:2) Approx. 3 1472×1104 Approx. 4 1280×960 Approx. 5 1280 (3:2) Approx. 5 Image appearing Recorded image 1024×768 Approx. 9 on the LCD screen 640×480 Approx. 46 To return to normal recording mode Select [NORMAL] in step 2. 37 38 1-9

Before performing advanced operations B Various recording

, Notes

Adding audio files to still Recording text documents Recording uncompressed • JPEG images are recorded in the image

images (VOICE) (DSC-S50 (TEXT) images (TIFF) size selected by the [IMAGE SIZE] menu. only) TIFF images are recorded in [1600 ×1200] Text is recorded in black and white This mode simultaneously records still size in DSC-S50, and [1280 ×960] size in 3 GIF format to provide a clearer image. images in both TIFF format DSC-S30 other than when [1600 (3:2)] or [1280 (3:2)] is selected. 1 (uncompressed) and JPEG format 3 • Writing data takes more time than in (compressed). normal recording. 2 3 • The supplied “Memory Stick” (4 MB) does not have sufficient capacity to record21uncompressed images. 1 Set the MODE selector to STILL. 1 Set the MODE selector to 2 Select [FILE], [REC MODE], STILL. and then [VOICE] from the menu. 2 Select [FILE], [REC MODE], 1 Set the MODE selector to and then [TEXT] from the STILL. 3 Record the image. menu. 2 Select [FILE], [REC MODE], If you press and release the shutter 3 Record the image. and then [TIFF] from the button, sound is recorded for menu. 5 seconds. The number of images that you can record on a “Memory Stick” (4 MB) 3 Record the image. If you hold down the shutter in TEXT mode: The number of images that you can button, sound is recorded until you Image size Number of images record on a “Memory Stick” release the shutter button for up to (16 MB) in TIFF mode: 40 seconds. 1600×1200 Approx. 12 to 87 Image size Number of images The number of images that you can 1600 (3:2) Approx. 14 to 97 record on a “Memory Stick” (4 MB) 1600×1200 Approx. 21472×1104 Approx. 14 to 97 in VOICE mode (when recording 1600 (3:2) Approx. 2 1280×960 Approx. 20 to 114 sound for five seconds): 1280×960 Approx. 3 1280 (3:2) Approx. 22 to 137 Image size Number of images 1280 (3:2) Approx. 3 1024×768 Approx. 30 to 160 1600×1200 Approx. 3 640×480 Approx. 80 to 363 To return to normal recording mode 1600 (3:2) Approx. 3 Select [NORMAL] in step 2. 1024×768 Approx. 8 To return to normal recording mode 640×480 Approx. 28 Select [NORMAL] in step 2. Notes To return to normal recording mode • If the subject is not evenly illuminated, you Select [NORMAL] in step 2. may be unable to record a clear image. • Writing and reading data takes more time When using the DSC-S30 than in normal recording. The DSC-S30 does not have a VOICE • The flash does not strobe in TEXT mode function. When you edit (delete, protect, or regardless of the surrounding brightness. copy files, etc.) files recorded in VOICE mode on a different camera, the still image file is edited but the audio file is not. 39 40 Landscape mode

Recording images in macro Setting the distance to the Using the PROGRAM AE Focuses only on a distant subject

subject function to record landscapes, etc. 2 Normally the focus is automatically Panfocus mode adjusted. This function is useful when Changes the focus quickly and 1 the auto focus does not work well such simply from a close subject to a as in dark places. distant subject. +/– Spot light-metering mode 1 Select this mode when there is22backlight or when there is strong 1 Set the MODE selector to contrast between the subject and MOVIE or STILL. the background, etc. Position the 2 Press FOCUS repeatedly 1 Set the MODE selector to point you want to record on the until the (auto macro) MOVIE or STILL. spot light-metering cross hair. indicator appears on the LCD 2 Press PROGRAM AE LCD screen screen. 1 Set the MODE selector to repeatedly to select the You can record a subject as close MOVIE or STILL. desired PROGRAM AE mode. as about 1 3/16 inches (3 cm) from the lens surface with the zoom set 2 Press FOCUS repeatedly to A Aperture priority mode all the way to the W side. achieve a sharp focus. Makes the subject stand out The 9 (manual focus) indicator against an unclear background or Spot light-metering To return to normal recording mode appears on the LCD screen. makes both the subject and the cross hair You can select from the following background stand out clearly. Press FOCUS repeatedly until 7 focus settings: auto (no Press +/– repeatedly to select an To cancel PROGRAM AE disappears from the LCD screen. indicator), (auto macro), aperture value in 9 steps from F2.8 Press PROGRAM AE repeatedly until to F11. Notes 1 3/4 feet (0.5m), 3 1/4 feet the indicator on the LCD screen goes • (1.0m), 9 3/4 feet (3.0m), 23 feet You cannot record images in macro with S Shutter speed priority out. the following PROGRAM AE modes. (7.0m), ∞ (infinite) mode — Landscape mode Records a sharp picture of a fast- Notes — Panfocus mode To reactivate auto focusing moving subject or the flow of • You cannot select F2.8 in aperture priority • You cannot record images in macro when Press FOCUS repeatedly until the motion of a moving subject. mode when the zoom is set to the T side. appears on the LCD screen. indicator disappears in step 2. • You can focus only on distant subjects in Press +/– repeatedly to select a Landscape mode. shutter speed in 18 steps from 8” Note • In Panfocus mode, the zoom position and to 1/725 when recording a still focus are fixed. These setting distances are approximate, and image and in 12 steps from 1/8 to • When you record in the Twilight plus should be used as a reference. 1/725 when recording a moving mode, we recommend that you use a tripod image. to prevent shaking. • Set the forced flash when you use the Twilight mode flash in the following modes: Suppresses the washed-out color –Twilight mode –Twilight plus mode of a bright subject in a dark place –Landscape mode so that you can record the subject • You cannot use the PROGRAM AE without losing the dark function when [REC MODE] is set to atmosphere of the surroundings. [TEXT]. • If the setting is not appropriate in aperture Twilight plus mode priority mode and shutter priority mode, Increases the effectiveness of the the setting value indicator on the LCD twilight mode function. screen flashes when you press the shutter button. In this case, reset the value. 41 42 1-10

B Various recording B Various recording

,

Adjusting the exposure Adjusting the white balance Recording the date and time Enjoying picture effects

(EXPOSURE) (WHITE BALANCE) on the still image (DATE/ (P.EFFECT) Normally the white balance is TIME) 1 automatically adjusted. 4 1 2,3112,3 2,3 2,3 1 Set the MODE selector to 1 Set the MODE selector to MOVIE or STILL. 1 Set the MODE selector to MOVIE or STILL. 2 1 Set the MODE selector to Select [CAMERA] and then STILL. MOVIE or STILL. 2 Select [EFFECT] and then [EXPOSURE] from the menu. 2 Select [EFFECT] and then [P.EFFECT] from the menu. 3 2 Select [CAMERA] and then Select the desired exposure [DATE/TIME] from the menu.[WHITE BALANCE] from the 3 Select the desired mode. value. menu. 3 Select the date and time Adjust the exposure value while SOLARIZE setting. checking the brightness of the 3 Select the desired white The light contrast is clearer and the background. You can select values balance setting. DAY&TIME picture looks like an illustration. ranging from +2.0 EV to –2.0 EV The date, hour and minutes are IN DOOR (n) B&W in steps of 1/3 EV. imposed onto the image.• Places where the lighting The picture is monochrome (black Note condition changes quickly DATE and white). • Under bright lighting such as The year, month and day are The exposure may not be adjusted properly SEPIA imposed onto the image. when the subject is extremely bright or dark, photography studios The picture is colored like an old or when using the flash. • Under sodium or mercury lamps OFF picture. OUT DOOR ( ) The date and time are not imposed NEG.ART Recording a sunrise/sunset, night onto the image. The color and brightness of the scene, neon signs, or fireworks 4 Record the image. picture are reversed. HOLD The date and time are not To cancel picture effect Recording a single-colored subject displayed during recording. or background The date and time are displayed Select [OFF] in step 3. when playing back images. AUTO (No indicator) Adjusts the white balance automatically To reactivate auto adjustment Select [AUTO] in step 3. Note Select [AUTO] when recording under fluorescent lighting. 43 44

B Various playback To display the next (previous) index Notes

screen Enlarging a part of the still • You cannot trim images recorded in TEXT

Playing back six images at Select v/V at the lower left of the LCD

screen. image (Zoom and trimming) mode or uncompressed images. once (INDEX) • The maximum zoom magnification is 5× 1 the original image, regardless of the image Displays the previous size. 1 index screen • The picture quality of trimmed images 3 may deteriorate. Displays the next index 2,4 • The original picture remains even after 2 screen trimming. • The trimmed image is recorded as the newest file. To return to normal playback (single image) 1 Set the MODE selector to 1 Set the MODE selector to • Select the desired image with the PLAY. PLAY. control button. 2 • Select [3] (RETURN). 2 Display the image to be Select [INDEX] on the LCD enlarged. screen. Note 3 Zoom in/out the image with Six images are displayed at once You cannot display images recorded in the zoom button. (index screen). TEXT mode on the INDEX screen. The zoom scaling indicator appears on the LCD screen. 4 Press the control button repeatedly to select the desired part of the image. v: The image moves downward V: The image moves upward b: The image moves rightward This shows the position of the B: The image moves leftward currently displayed images relative to all the recorded images. To return to the normal size Zoom in with the zoom button until the The following marks are displayed on each image according to the zoom scaling indicator ( × 1.1) image type and settings. disappears from the screen, or simply : Moving image file press z. : Voice memo file : E-mail file To record an enlarged image : Print mark (trimming) - : Protect mark 1Enlarge the image. TEXT: Text mark TIFF: TIFF mark 2Press the shutter button. The image (No mark): Normal recording (no is recorded at 640× 480 size, then the settings) display returns to the image display before enlargement. 45 46 1-11

B Various recording B Various playback

, Note

Rotating a still image Playing back the images in The [INTERVAL] setting time is Viewing images on a TV

(ROTATE) order (SLIDE SHOW) approximate, and may vary depending on screen the played back image size or other factors. This function is useful for checking the Before connecting your camera, be 1 recorded images or for presentations, sure to turn off the TV. After etc. connecting A/V connecting cable 2,3,4 (DSC-S50) or VIDEO connecting 1 cable (DSC-S30), turn on the TV. 2,3 Set the TV/VIDEO switch to VIDEO. 1 Set the MODE selector to PLAY. A/V connecting cable or 2 Display the image to rotate. VIDEO connecting cable 3 Select [FILE] and then 1 Set the MODE selector to (supplied) [ROTATE] from the menu. PLAY. 4 Rotate the image clockwise 2 Select [FILE] and then [SLIDE or counterclockwise , SHOW] from the menu. then select [RETURN]. Set the following items.

INTERVAL

Notes to A/V OUT jack or 1 MIN (one minute), 30 SEC • You may not be able to rotate protected VIDEO OUT jack(30 seconds), 10 SEC images or images recorded with other (10 seconds), 5 SEC (5 seconds), equipment. 3 SEC (3 seconds) 1 Connect your camera and the • Also, when viewing images on a personal TV. computer, the image rotation information REPEAT may not be reflected depending on the ON: Plays back images in a DSC-S50 application software. continuous loop until Connect the A/V connecting cable • You cannot rotate protected or [RETURN] is selected. to the A/V OUT jack of your uncompressed images, or images recorded camera and to the audio/video in TEXT mode. OFF: After all images have been played back, the slide show input jacks of the TV. ends. If your TV has stereo type audio 3 input jacks, connect the audio plug Select [START] with the of the A/V connecting cable to the control button. Lch jack. The slide show begins. DSC-S30 To cancel the slide show Connect the video cable to the VIDEO OUT jack of your camera Select [CANCEL] in step 2 or 3. and to the video input jack of the TV. To skip to the next/previous image during slide show playback 2 Turn on the TV, then start Select / at the lower left of the LCD playback on your camera. b B screen. The playback image appears on the TV screen. Note You cannot use a TV that has an antenna 47 48 (aerial) connector only.

B Editing The selected images are protected. The (delete) indicator appears Deleting images (DELETE) on the selected images and these

images are deleted.

Preventing accidental erasure You cannot delete protected files.

(PROTECT) The - (protect) indicator appears on 1 protected images. 1,2,3 1 To release protection If you selected [ALL] in step 2, select 1,2,3 [OFF]. If you selected [SELECT] in To cancel deleting step 2, select the images to unprotect In single mode Select [CANCEL] in step 2 or 3. with the control button, then select [ENTER]. 1 Set the MODE selector to Note PLAY, then display the image If there are files on the “Memory Stick” with

In single mode to delete. names having the same last 4 digits as the

file name of the image to be deleted, these 1 Set the MODE selector to 2 Select [DELETE] and then files are also deleted at the same time. PLAY, then display the image [OK] from the menu. to protect. The image is deleted. 2 Select [FILE], [PROTECT], and then [ON] from the menu. In INDEX mode The displayed image is protected - 1 Set the MODE selector to and appears. PLAY, then display the INDEX screen. To release protection Select [OFF] in step 2. 2 Select [DELETE] and then [ALL] or [SELECT] from the menu.

In INDEX mode 3 When you select [ALL]

1 Set the MODE selector to Select [ENTER]. PLAY, then display the INDEX All unprotected images are screen. deleted. 2 Select [FILE], [PROTECT], When you select [SELECT] and then [ALL] or [SELECT] Select all the images to delete with from the menu. the control button, then select 3 [ENTER]. When you select [ALL] Select [ON]. All the images recorded in “Memory Stick” are protected. When you select [SELECT] Select all the images to protect with the control button, then select [ENTER]. 49 50 1-12

B Various playback B Editing

, After copying is finished

Changing the recorded still Copying images (COPY) In INDEX mode Select [EXIT].

image size (RESIZE) If you do not select [EXIT], the same You can copy images to another image is copied each time you “Memory Stick.” 1 exchange the “Memory Stick.” 1 1,2,3 In single mode 1,2,3,4 To cancel copying part-way Change the MODE selector setting or turn off the power. 1 Notes Set the MODE selector to 1 1,2 • You cannot copy uncompressed images. PLAY, then display the INDEX Set the MODE selector to • You cannot copy images that are bigger screen. PLAY and display the image than 1.4 MB at once. If “NOT ENOUGH to resize. 2 Select [TOOL], [COPY], and MEMORY” appears or flashes on the INDEX screen, cancel some images to 2 then [SELECT] from the Select [TOOL] and then 1 copy and try again. Set the MODE selector to menu. [RESIZE] from the menu. PLAY, then display the image 3 to copy. 3 Select the image to copy.Select the desired image The (select) indicator appears size. 2 Select [TOOL], [COPY], and on the image. DSC-S50 then [OK] from the menu. × × × “FILE ACCESS” appears. 4 Select [ENTER].1600 1200, 1024 768, 640 480 “MEMORY STICK ACCESS” DSC-S30 3 When “CHANGE MEMORY appears. 1472×1104, 1280 ×960, STICK” appears, eject the × × “Memory Stick.” 5 When “CHANGE MEMORY 1024 768, 640 480 “INSERT MEMORY STICK” STICK” is displayed, eject the The changed image is recorded, appears. “Memory Stick.” “INSERT MEMORY STICK” then the display returns to the 4 Insert the “Memory Stick” on appears. image display before resizing. which to copy the image. “RECORDING” appears. When 6 Insert another “Memory To return to the original size copying is completed, Stick.” Select [CANCEL] in step 3. “COMPLETE” appears. “RECORDING” appears. When If you exchange the “Memory copying is completed, Notes Stick,” the same image is copied “COMPLETE” appears. • You cannot change the size of images again. If you exchange the “Memory recorded in TEXT mode or uncompressed Stick,” the same image is copied images. again. • When you change from a small size to a After copying is finished large size, the picture quality deteriorates. Select [EXIT]. • The original image is retained even after If you do not select [EXIT], the same resizing. image is copied each time you • The resized image is recorded as the exchange the “Memory Stick.” newest file. 51 52 4 Select [ENTER]. How to prevent moisture

Selecting still images to print Additional information of the selected images change condensation

(PRINT MARK) from green to white. Precautions When bringing the camera from a cold place to a warm place, seal the camera in a plastic You can mark a print mark on still bag and allow it to adapt to conditions at the images recorded with your camera. On cleaning new location over a period of time (about an This mark is convenient when you hour). have images printed at a shop that Cleaning the LCD screen If moisture condensation occurs conforms with the DPOF (Digital Print Wipe the screen surface with a cleaning cloth (not supplied) or a LCD cleaning kit Turn off the camera and wait about an hour Order Format) standard. (not supplied) to remove fingerprints, dust, for the moisture to evaporate. Note that if etc. you attempt to record with moisture 1 To unmark selected print marks remaining inside the lens, you will be Select the images to unmark in step 3 Cleaning the camera surface unable to record clear images. Clean the camera surface with a soft cloth 1,2,3,4 with the control button, then select [ENTER]. slightly moistened with water, then wipe the surface dry. Do not use any type of solvent On AC power adaptor such as thinner, alcohol or benzene as this To unmark all the print marks may damage the finish or the casing. • Unplug the unit from the wall outlet Select [FILE], [PRINT MARK], (mains) when you are not using the unit for After using your camera at the a long time.

In single mode [ALL] and then [OFF] from the menu. seashore or other dusty locations • To disconnect the power cord (mains lead),

of all images are unmarked. pull it out by the plug. Never pull the 1 Clean your camera carefully. Otherwise, the Set the MODE selector to salty air may corrode the metal fittings or power cord (mains lead) itself. PLAY and display the image Notes dust may enter the inside of your camera, • Do not operate the unit with a damaged you want to print. • You cannot mark moving images or causing a malfunction. cord or if the unit has been dropped or images recorded in TEXT mode. damaged. 2 Select [FILE], [PRINT MARK], • If you mark an image recorded in TIFF • Do not bend the power cord (mains lead) and then [ON] from the menu. mode with a print mark, only the Note on operating forcibly, or place a heavy object on it. This The (print) mark is displayed uncompressed image is printed, and the temperature will damage the cord and may cause fire or on the image. JPEG image recorded at the same time is Your camera is designed for use between the electrical shock. not printed. temperatures of 32˚F and 104˚F (0˚C and • Prevent metallic objects from coming into To unmark the print mark 40˚C). Recording in extremely cold or hot contact with the metal parts of the places that exceed this range is not connecting section. If this happens, a short Select [OFF] in step 2. recommended. may occur and the unit may be damaged. • Always keep metal contacts clean. • Do not disassemble the unit.

In INDEX mode On moisture condensation • Do not apply mechanical shock or drop the

1 unit.Set the MODE selector to If the camera is brought directly from a cold • While the unit is in use, particularly during PLAY, then display the INDEX to a warm location, or is placed in a very charging, keep it away from AM receivers screen. damp room, moisture may condense inside and video equipment. AM reception and or outside the camera. Should this occur, the 2 video operation are disturbed.Select [FILE], [PRINT MARK], camera will not operate properly. • The unit becomes warm during use. This is and then [SELECT] from the Moisture condensation occurs not a malfunction. menu. easily when: • Do not place the unit in locations that are: 3 — Extremely hot or coldSelect the images to mark • The camera is brought from a cold location such as a ski slope into a warmly heated — Dusty or dirtywith the control button. room. — Very humid • The camera is taken from an air- — Vibrating conditioned room or car interior to the hot outdoors, etc. 53 54 1-13

B Editing B Editing

,

On battery pack “Memory Stick”, , “MagicGate PAL-M system countryOn “Memory Sticks” Memory Stick” and are trademarks of Brazil

• Use only the specified charger with the Sony Corporation. charging function. “Memory Stick” is a new compact, portable “MagicGate” and are PAL-N system countries • To prevent accident from a short circuit, do and versatile IC recording medium with a trademarks of Sony Corporation. Argentina, Paraguay, Uruguay not allow metal objects to come into data capacity that exceeds a floppy disk. “Memory Stick” is specially designed for SECAM system countriescontact with the battery terminals. • Keep the battery pack away from fire. exchanging and sharing digital data among Bulgaria, Czech Republic, France, • Never expose the battery pack to “Memory Stick” compatible products. Using your camera abroad Guiana, Hungary, Iran, Iraq, Monaco, temperatures above 140˚F (60˚C), such as Because it is removable, “Memory Stick” Poland, Russia, Slovak Republic, in a car parked in the sun or under direct can also be used for external data storage. Power sources Ukraine, etc. sunlight. You can use your camera in any • Keep the battery pack dry. There are two types of “Memory Sticks”: country or area with the supplied • Do not expose the battery pack to any general “Memory Sticks” and “MagicGate mechanical shock. Memory Sticks” that are equipped with the battery charger within 100 V to 240 V • Do not disassemble nor modify the battery MagicGate* copyright protection AC, 50/60 Hz. Use the supplied AC pack. technology. power adaptor [a], if necessary, • Install the battery pack to the camera You can use both types of “Memory Stick” depending on the design of the wall securely. with your camera. However, because your outlet (mains) [b]. • Charging while some capacity remains camera does not support the MagicGate does not affect the original battery standards, data recorded with your camera is capacity. not subject to MagicGate copyright AC-L10 protection. If any problem occurs, unplug your camera ∗ MagicGate is copyright protection and contact your nearest Sony dealer. technology that uses encryption technology.

On internal rechargeable Watching the playback picture on Notes

button battery TV• Do not remove the “Memory Stick” while If you want to view the playback This camera has an internal rechargeable reading or writing data. picture on a TV, you need a TV having button battery for maintaining the date and • Data may be damaged if: time and other settings regardless of — you remove the “Memory Stick” or turn a video input jack and a video whether the power is on or off. This off your camera while reading or connecting cable. writing data. The color system of the TV must be rechargeable button battery is constantly charged as long as you are using the camera. — you use the “Memory Stick” in a the same as that of your digital still However, if you use the camera for only location subject to the effects of static camera. TV color systems differ from short periods it discharges gradually, and if electricity or noise. country to country. Check the you do not use the camera at all for about • Do not attach any other material than the following list: half a year it becomes completely supplied label on the labeling position. discharged. In this case, be sure to charge • Attach the label so that it does not stick out NTSC system countries this rechargeable button battery before using from the proper attachment location. Bahama Islands, Bolivia, Canada, the camera. • When you carry or store the “Memory Central America, Chile, Columbia, However, even if this rechargeable button Stick,” put it in its supplied case. Ecuador, Jamaica, Japan, Korea, battery is not charged, you can still use the • Do not touch the terminals of a “Memory Mexico, Peru, Surinam, Taiwan, the camera as long as you do not record the date Stick” with your hand or a metal object.• Do not strike, bend or drop the “Memory Philippines, the U.S.A., Venezuela, etc.and time. Stick.” PAL system countries Charging method • Do not disassemble or modify the Australia, Austria, Belgium, China, Connect the camera to a wall outlet (mains) “Memory Stick.” Denmark, Finland, Germany, Great with the AC power adaptor, or install a • Do not allow the “Memory Stick” to get wet. Britain, Holland, Hong Kong, Italy, charged battery pack, and leave the camera for 24 hours or more with the POWER Kuwait, Malaysia, New Zealand, switch set to OFF. Norway, Portugal, Singapore, Spain, Sweden, Switzerland, Thailand, etc. 55 56

Troubleshooting Symptom Cause and/or Solution

The picture is too dark. • You are shooting a subject with a light source If you experience trouble with your camera, first check the following items. Should behind the subject. your camera still not operate properly after you have made these checks, consult your tAdjust the exposure (page 43). Sony dealer or local authorized Sony service facility. If code displays (C:ss:ss) tAdjust the brightness of the LCD screen (page appear on the LCD screen, the self-diagnosis display function is working (page 62). 35). The flash does not work. • The flash is set to . Symptom Cause and/or Solution tSet the flash to auto (no indicator), or (page 19). Your camera does not • You are not using an “InfoLITHIUM” battery pack. work. • PROGRAM AE is set to the Twilight, Twilight tUse an “InfoLITHIUM” battery pack (page 8). plus, or Panfocus mode. • The battery level is low (the E indicator appears tCancel the mode (page 42) or set the flash to on the LCD screen).tCharge the battery pack (page 9). • The MODE selector is set to MOVIE (DSC-S50 • The AC power adaptor is not connected securely. only). tConnect it firmly to the DC IN jack of your tSet it to STILL. camera and a wall outlet (mains) (page 12). • The built-in microcomputer is not working The date and time are • The date and time are not set correctly. properly. recorded incorrectly. tSet the correct date and time (page 13). tDisconnect and then reconnect all power Vertical streaks appear • The smear phenomenon is happening. sources after one minute. Then turn the power when you are shooting a tThis is not a malfunction. on by sliding the POWER switch down and very bright subject. check that the camera works properly. The battery life is short. • You are recording/playing back images under Your camera cannot • The MODE selector is set to PLAY. extremely cold temperatures. record images. tSet it to MOVIE or STILL (pages 16, 20). • The battery pack is not charged enough. • No “Memory Stick” has been inserted into your tCharge the battery pack fully. camera. • The battery pack is dead. t Insert a “Memory Stick” (page 15). tReplace the battery pack with a new one. • The write-protect tab on the “Memory Stick” is set The battery remaining • You have used the camera for a long time in an to LOCK. indicator is incorrect. extremely hot or an extremely cold location. tSet it to the recording position. • The battery pack is dead. The picture is out of focus. • Your camera is not in macro recording mode when tReplace the battery pack with a new one (page you shoot a subject that is about 1 3/16 to 8). 9 7/8 inches (3 to 25 cm) away from the lens. • The battery pack is discharged. tSet the macro recording mode (page 41). t Install a charged battery pack (pages 8, 9). tPress the zoom button to set to the W side. Sufficient battery tFully charge the battery pack (page 9). The resizing function does • You cannot resize moving images and text images. remaining indicator is not work. displayed but the power runs out soon. You cannot display a print • You cannot display print marks on moving images mark. and text images. The zoom does not work. • PROGRAM AE is set to the Panfocus mode. The picture is noisy. • Your camera is placed near a TV or other tCancel the Panfocus mode (page 42). equipment that uses strong magnets. Digital zoom does not • You cannot use digital zoom to record moving tMove your camera away from the TV, etc. function. pictures. 57 58 1-14

Additional information Additional information

, Symptom Cause and/or Solution Symptom Cause and/or Solution Your camera cannot play • The MODE selector is set to STILL or MOVIE. Your personal computer • The camera is turned off. back images. tSet it to PLAY (page 21). does not recognize your tTurn on the camera. The image and sound • You are playing back the file directly from the camera. • The battery level is low. break off when you play “Memory Stick.” tUse the AC power adaptor (page 12). back an image on a tCopy the file to the hard disk of the personal • The USB cable is not connected firmly. personal computer. computer and then play back the file from the tDisconnect the USB cable, and connect it again hard disk (page 27). firmly. Make sure that “PC MODE” is displayed The image cannot be tConsult the personal computer or software on the LCD screen (page 26). played back on a personal manufacturer. • The USB connectors on your personal computer computer. are connected to other equipment besides the keyboard, the mouse, and your camera. Your camera cannot delete • The image is protected. an image. tDisconnect the USB cables except for the ones tCancel the protection (page 49). connected to the keyboard, the mouse, and your The power turns off • With the MODE selector set to STILL or MOVIE, camera (page 24). suddenly. if you do not operate the camera for about three minutes while the power is on, the camera turns off automatically to prevent wearing down the battery. tTurn on the camera. • The battery is discharged. tReplace it with a charged battery. The image does not • The video output signal setting of your camera is appear on the TV screen. incorrect. tChange the setting (page 48). A file error occurs when • The image size is larger than 1600 ×1200. you play back a file. tUse an image size of 1600 ×1200 or smaller. The PROGRAM AE • The camera is set to text mode. function does not work. tCancel text mode (page 42). The LCD screen freezes • This is a characteristic of the system and is not a momentarily. malfunction. 59 60

Warning and notice messages Self-diagnosis display

Various messages appear on the LCD screen. Check the corresponding descriptions Your camera has a self-diagnosis display. This in the following list. function displays the camera condition on the LCD screen with a combination of a letter and Message Meaning four digits of numbers. If this occurs, check the following code chart. The code informs you of the NO MEMORY STICK No “Memory Stick” has been inserted. camera’s current condition. The last two digits SYSTEM ERROR Turn the power off and on again. (indicated by ss) will differ depending on the state of the camera. MEMORY STICK ERROR The inserted “Memory Stick” cannot be used with your camera, or is damaged. Self-diagnosis display FORMAT ERROR Failed to format the “Memory Stick.” • C:ss:ss You can reverse the camera MEMORY STICK LOCKED The write-protect tab on the “Memory malfunction yourself. Stick” is set to the LOCK position. • E:ss: ss Contact your Sony dealer or local NO MEMORY SPACE The capacity of the “Memory Stick” is authorized Sony service facility. full, and you cannot record or copy images. First three digits Cause and/or Corrective Action NO FILE No image has been recorded on the C:32:ss • There is trouble with your camera’s hardware. “Memory Stick.” tTurn the power off and on again. FILE ERROR An error occurred while playing back the image. C:13:ss • An unformatted “Memory Stick” is inserted. tFormat the “Memory Stick” (page 32). FILE PROTECT The image is protected against erasure. • The inserted “Memory Stick” cannot be used with for “InfoLITHIUM” battery only The battery is not the “InfoLITHIUM” your camera, or is damaged. type. t Insert a new “Memory Stick” (page 15). NOT ENOUGH MEMORY The images you want to copy are too big E:61:ss • A camera malfunction that you cannot reverse has to copy with your camera. E:91:ss occurred. DIRECTORY ERROR A directory with the same name already tContact your Sony dealer or local authorized exists. Sony service facility and inform them of the 5- digit service code. (example: E:61:10) IMAGE SIZE OVER You are playing back an image of a size that cannot be played back with your If you are unable to solve the problem even after trying the corrective camera. actions a few times, contact your Sony dealer or local authorized Sony INVALID OPERATION You are playing back a file that was service facility. created on equipment other than your camera. E The battery level is low or zero. - The image is protected. 61 62 1-15

Additional information Additional information

,

LCD screen indicators The indicators during recording

A Battery remaining indicator J Self-diagnosis function/ recording time indicator B PROGRAM AE/flash level/flash mode indicator K Number of recorded images C White balance/EV level/ L Remaining memory capacity sharpness indicator indicator D Picture effect indicator M Moving image/VOICE recording time indicator (DSC-S50 only) E Date/time indicator N Self-timer indicator F Aperture/shutter speed indicator O Spot light-metering indicator G AE lock/focus lock indicator P Focus/macro mode indicator H Recording mode indicator Q Menu bar and guide menu I Image size indicator They appear by pressing v on the control button and disappear by pressing V of it. 11-1-166 E,

DSC-S30/S50 SECTION 2 DISASSEMBLY

• This set can be disassembled in the order shown below. 2-1. PD-127 BOARD AND SERVICE POSITION DSC-S30/S50 INDICATOR MODULE (LCD PANEL AND PD-127 BOARD) (page 2-2) (page 2-2) 2-2. FRONT CABINET BLOCK

ASSEMBLY

(page 2-3) 2-3. BATTERY LID ASSEMBLY 2-5. MS-50 BOARD AND AND CONTROL SWITCH BT HOLDER ASSEMBLY BLOCK (page 2-3) (page 2-4) 2-4. FLASH UNIT AND 2-6. LENS BLOCK ASSEMBLY UPPER CABINT BLOCK (page 2-5) (page 2-4) 2-7. SY-58 BOARD, DD-141 2-9. HINGE ASSEMBLY AND BOARD AND JK-194 BOARD KJ-11 BOARD (page 2-5) (page 2-7) 2-8. CONTROL SWITCH BLOCK OVERALL CHECK SERVICE AND SW-339 BOARD POSITION (page 2-6) (page 2-6) • ATTACHMENT OF CPC-9 JIG BT holder assembly Open the battery lid assembly SY-58 board (CN709) CPC lid CPC lid (Note 3) 18 CPC-9 jig (J-6082-393-C) (18P flexible board) (Note 1, 2) Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 3: In removing the CPC lid, start from the upper side. 2-1, Note: Follow the disassembly procedure in the numerical order given. 2-1. PD-127 BOARD AND INDICATOR MODULE 8 Flexible board 7 Flexible board (CN851) (CN901) 0 PD-127 board and 9 Two claws qg Indicator module inverter transformer unit qs Screw qf Cold cathode (1.7 × 4) fluorescent tube5Pcabinet (Rear) 4 Two claws qa Two connectors (CN801, 802) 1 Screw (M2) qd Two screws (M1.7) 3 Two screws 2 Screw (M2) (M2) 6 Screw (M1.7) Display block Note: In removing 3 two screws, rotate the display block. [SERVICE POSITION (LCD PANEL and PD-127 BOARD)] Note 1: Don't use the 12 pin flexible board of CPC-9 jig. Adjustment remote It causes damage to the unit. commander Note 2: The old CPC-9 jit (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Cold cathode fluorescent tube Indicator module Inverter transformer unit CPC-9 jig (J-6082-393-C) (Note 1, 2) PD-127 board AC power adaptor AC IN 2-2, 2-2. FRONT CABINET BLOCK ASSEMBLY 5 Two screws 6 Two screws × (2 × 4)(2 4) 1 Open the battery lid assembly. 9 Connector (CN706) 8 Flexible board (CN707) 4 Screw qa CPC lid (2 × 4) BT holder assembly 0 Two connectors (CN710, 712) (S50) 2 Screw 0 Connector (2 × 4) (CN712) (S30) 7 Front cabinet block assembly CPC lid 3 Screw (2 × 4) Note: In removing the CPC lid, start from the upper side. 2-3. BATTERY LID ASSEMBLY AND CONTROL SWITCH BLOCK 4 Remove the control switch block (Mode SW) in the direction 3 Screw of arrow A. (1.7 × 4) Note: In mounting the control switch block (Mode SW), 1 Battery lid align the mode SW konb assembly A with the sleeve knob. 2 Screw (1.7 × 4) Sleeve 2-3, 2-4. FLASH UNIT AND UPPER CABINET BLOCK 1 Two screws (1.7 × 4) 3 Upper cabinet block Capacitor 4 Flash unit Note: Do not touch the capacitor terminals. You could get an electric shock. 2 Claw 8 Speaker (S50) 5 Buzzer (S30) 7 Microphone unit 6 MISP holder 5 Three screws (1.7 × 4) (S50) 2-5. MS-50 BOARD AND BT HOLDER ASSEMBLY 0 DC-IN connector 1 Connector (CN001) 9 BT holder 8 Screw assembly (1.7 × 4) 4 MS-50 board 3 Three screws (1.7 × 4) 7 Screw (1.7 × 4) 5 Connector (CN005) 6 Connector (CN002) 2 FP-024 flexible board (CN003) 2-4, 2-6. LENS BLOCK ASSEMBLY 1 FP-023 flexible board (CN101) 2 Flexible board (CN183) 3 Screw (1.7 × 4) 4 Lens block assembly 2-7. SY-58 BOARD, DD-141 BOARD AND JK-194 BOARD 7 Three connectors (CN701, 702, 713) 6 Flexible board (CN708) 5 SY-58 board 8 Screw (M1.7 ) 2 FP-025 flexible board (CN703) 4 Two screws qd Open the JK lid. (1.7 × 4) qf JK-194 board qs Screw qa DD-141 board (1.7 × 4) 3 Screw (1.7 × 4) 1 FP-026 flexible 9 Screw board (CN201) 0 Connector (M1.7) (CN711) Note: Do not remove these two screws. 2-5, 2-8. CONTROL SWITCH BLOCK AND SW-339 BOARD 3 Control switch block (Zoom/power SW) 1 Two screws (1.7 × 4) 2 Screw (1.7 × 4) 4 Two screws Note: In mounting the SW-339 board, (1.7 × 4) align the SW knob (S109) with the slide knob holder. 5 Screw (1.7 × 4) 6 SW-339 board Slide knob holder S109 [OVERALL CHECK SERVICE POSITION] Adjustment remote commander DC-IN connector AC IN AC power CPC-9 jig adaptor (J-6082-393-C) (Note 1, 2) Memory stick MS-58 board SY-58 Lens board block Control switch assembly block (Mode SW) DD-141 board Capacitor Extention cable (J-6082-423-A) Flash unit (Note 3) SW-339 Power SW board Extention cable (J-6082-398-A): L=200mm Note 1: Don't use the 12 pin flexible board of CPC-9 jig. (J-6082-357-A): L=100mm JK-194 It causes damage to the unit. board Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) Cannot be used, because it cannot operate the adjustment remote commander. Note 3: Do not touch the capacitor terminals. You could get an electric shock. 2-6, 2-9. HINGE ASSEMBLY AND KJ-11 BOARD 0 Remove the hinge assembly after turning it toward arrow6Pcabinet (Front) A direction. A 7 Two screws (M1.7) 8 BL fixed plate 4 Screw 9 Three screws (M1.7) (M1.7) 5 Hinge cover (B) qs KJ-11 board qa KJ clip 1 Screw (M1.7) 3 Hinge cover (T) 2 Claw 2-7, 2-10. CIRCUIT BOARDS LOCATION Inverter transformer unit Cold cathode SY-58 fluorescent ( A UCA D IO , T GMERA, /AD I FS EP L , LENSDRIVE, tubeAY, MEMORYCONTROL, ) SH DISP, HI CONTROL Indicator module Flash unit PD-127 ( L CD DRIVE,TIMINGGENERATOR) KJ-11 (PANEL REVERSE) SW-339 (SWITCH) MS-50 ( F U / M EMORYSTICK ) CD-262 (CCD IMAGER) DD-141 ( D C / DCCONVERTER,VIDEO, USB ) JK-194 (USB, A/V OUT) 2-11. FLEXIBLE BOARDS LOCATION Control switch block (Mode SW) FP-025 FP-023 Control switch block (Zoom/Power SW) FP-024 FP-026 22-8-8 E, CNT C CNT Y CAM SO, CAM SI, XCAM SCK HI SO, HISI, XHI SCK

DSC-S30/S50 SECTION 3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM

CD-262 BOARD SY-58 BOARD PD-127 BOARD BL UNIT

IC901 LCD901IC301 DATA BUS IC302 IC303 IC801 LCD T. G. CAMERA DSP, 64M SDRAM I/O COLOR IRIS MEMORY CONTROL, ADDRESS BUS EXP (EVR) (SEE PAGE 4-35) LCD LENS METER IC301 IC102 VIDEO DECODER (SEE PAGE 4-23, 24)CCD (SEE PAGE 4-33) UNIT CCD S/H, AGC,OUT OPD, OSD, IMAGER A/D DATA BUS 12 HOST IF, SG, CONVERTER JPEG, L-MODE, IC802 RES CONTRLYYLCD (SEE PAGE 4-8) (SEE PAGE 4-17) R-Y R-Y DRIVE B-Y B-Y (SEE PAGE 4-22) (SEE PAGE 4-34)

AUSDTI

IC101 IC252 IC253 BZ901 S30 TIMING AUDIO AUDIO BUZZER GENERATOR AUSDTOCAM SO, CAM SCK AD/DA CON AMP S50 (SEE PAGE 4-15) (SEE PAGE 4-16) SP SP901 Y-OUT MIC SPEAKER (SEE PAGE 4-17) C-OUT HI SO, HI SI, HI SCK MIC901 DRIVE (–) IC184 MICROPHONEIC186 IC185 EVR D/A (SEE PAGE 4-19, 20) CONVERTER 16 DATA BUS ABCD IRIS IC501 MS-50 BOARD CN004 DRIVE (SEE PAGE 4-20) MC CAM. (SEE PAGE 4-9, 10) 10

H HALL (+)

HALL HALL AD AMP 14 ADDRESS BUS ABCD MS SCLK, MS BS, MS DIO MEMORY (SEE PAGE 4-26) STICK MC_XCSO IC182 XMS IN MSHUT ON MC_XRD 1 (SEE PAGE 4-19) 16 IC504 IRIS FLASH ROM DRIVE IRIS EN M901 20 JK-194 BOARD FOCUS FOCUS MOTOR PE ENO (SEE PAGE 4-28) AU OUT (SEE PAGE 4-40)M S30 MOTOR DRIVE V OUT J201 XZM RST SENS 16 IC505 VIDEO OUT FOCUS MOTOR XFC RST SENS SDRAM XCKE, XCS3, Y-OUT IC802SENSOR XRAS, XCAS, C-OUT V OUTVIDEO J201 S50 IC183 PE EN1

XRDWR

M902 12 CNT Y AMP A/V(SEE PAGE 4-28) ZOOM CNT C OUTM ZOOM MOTORMOTOR (SEE PAGE 4-46)DRIVE PE DIR CN202 ZOOM MOTOR (SEE PAGE 4-19) 1A/1B D (+) SENSOR IC851 USB DATA USB I/F

FLASH UNIT D (–) USB

(SEE PAGE 4-47) CAM SO, CAM SI, XCAM SCK STRB ON USB DET FLASH PHOTO TR OUT UNIT HALL AD HALL AD HI SO, HI SI, XHI SCK STB CHARGE IC404 CNT Y, CNT C XMS IN XMS IN

CONTROL SWITCH BLOCK HI EXT STROB ON

(ZOOM POWER SWITCH) XPWR SW XCS, WE IC406 POWER SWITCH (SEE PAGE 4-30) EEPROM (SEE PAGE 4-30) ZOOM SW AD IC507 1.8VS ZOOM SWITCH BL ON IC001EEPROM 1.8VP BL LED ON (SEE PAGE 4-27) PANEL –15.3V DC CONTROL MOVIE/STILL SW PANEL PWM CAM –7.5V MOVIE/STILL/PLAY FAST CHATGE FAST CHARGE (SEE PAGE 4-43) FAST CHG SWITCH XCAM/PB SW CAM 15VINIT CHARGE ON INIT CHARGE ON PANEL 13.2V XSHTR LOOK SW INIT CHG SHUTTER PANEL 6.5V SWITCH XSHTR SW IC402 IC401 D401 CAM P 5V XREST RESET REG BATT UNREG SP 5V SYS DD

CONTROL SWITCH BLOCK ACV UNREG

(MODE SW) (SEE PAGE 4-29) (SEE PAGE 4-29) A 3.2V LCD DD D402 PANEL 3.2V BACKUP VCC CAM 3.2V SYS DD ON SYS DD ON D 3.2V CN001 LCD DD ON LCD DD ON PANEL 4.9V BATT XEXT BATT XEXT A 4.9V DC IN BATT SIG BATT SIG ACV UNREG

SW-339 BOARD IC405 BATT UNREG

TIMER + BT901 CLOCK S BATTERY FUNCTION AD1 – 3 (SEE PAGE 4-30) – TERMINALKEY VL 3V BT101 LITHIUM BATTERY DD-141 BOARD 3-1 3-2,

VCC DSC-S30/S50

3-8. POWER BLOCK DIAGRAM 1

MS-50 BOARD DD-141 BOARD

(SEE PAGE 4-9, 10 ) CN005 CN001 CN852 FAST CHARGE FAST CHARGE1169 INT CHARGE ON INIT CHARGE ON2271 SYS DD ON SYS DD ON LCD DD ON CN001 ACV UNREG F005 ST UNREG ST UNREG1 517 7 BATT/XEXT ST UNREG 53 DC IN 3 R005 F004 8 8BL UNREG 2 BU UNREG 639 9 65 F003 10 UNREG3Q002 Q003 10 11 UNREG3F002 11UNREG2 12 12 D006 UNREG2 CN002 F001 13 13 + BATT UNREG BATT UNREGBT901 1 14 14 64BATT SIG BATTERYS2Q004 TERMINAL – 3 L001 SWITCHING Q009, 013L006 B+ D1.8VS 41 SWITCH 43D1.8VP 42 D003, 004 Q021, 024, 030 44 SWITCHING B– PANEL –15.3VRECT 62 CN003 Q034 SWITCH 2 BATT SIG D002 TO BATT/XEXT (ACCESS LED) 1 T001 D002 Q020, 023, 026, 029 SY-58 BOARD A4.9V B– CAM –7.5V CN70433SWITCH 50 (SEE PAGE 3-15) MS VCC 2 CAM 15V 5 52 L002 Q001 SWITCHING Q019, 027, 031, 033IC001 6 10 CN004 4 B+ PANEL 13.2V

TO

SY-58 BOARD DC CONTROL 60 VCC EMERGENCY SWITCH CN7113 (SEE PAGE4-43) DETECT MEMORY STICK VCC18(SEE PAGE 3-17) 9 18 Q010 Q020, 032, 025, 028 OUTA 46 D001 1 B+ PANEL 6.5V OUTB 44 SWITCH 58 SCPC 24 L004 L011 CAM P5V 55 POW CONT 20 57 Q003 SP 5VCTLB 21 59 CTLCD 22 SWITCHING 1.0 Vp-p OUTC 40 2.1µsec SCPB 13 IC002 rf SCPA 8 R072 A3.2V 37 Q002 SWITCHING 39 SCPD 29 SWITCHING L003 L012 Q036 PANEL 3.2V L009 CAM 3.2V 46 L005 D3.2V 45 16 RT OUTD 39 47 Q005 – 008 Q014, 016 17 L014CT B+ PANEL 4.9VREG SWITCH 56 LCD DD ON L008 A4.9V 38 VREF 19 L801 Q806, 807 IC851 USB IF A3.2V (SEE PAGE 4-47) IC802 VIDEO AMP (SEE PAGE4-46) 3-15 3-16,

DSC-S30/S50

3-9. POWER BLOCK DIAGRAM 2

SY-58 BOARD SW-339 BOARD

IC404

HI

CN711 (SEE PAGE 4-30) CN704 BATT/XEXT 12 FAST CHARGE 100 BATT/XEXT 20 14 CN706 FAST CHARGE Q409 ST UNREGINIT CHARGE ON 8 10 27 INIT CHARGE BATT SI 48 BATT SIG SYS DD ON IF 11 29 SYS DD ON BATT SG 49 BLOCK 13 TO FLASH LCD DD ON MS-54 BOARD 13 47 LCD DD ON Q701, 702 UNITCN003 D3.2V MS VCC CHARGE LED POWER LED 2 (SEE PAGE 3-13) A4.9V4194 60 A4.9V 12 MS ON D411 D412 CPC(IC501) (BATT CHARGE) (POWER LED) (FOR CHECK) 10 18 D102 CN709 IC401 LED BACK UP VDD BACK UP VDD 2 CN703REG 3 CN101 (SEE PAGE 4-29) A4.9V A4.9V D3.2V D3.2V D401 D402 6 2D3.2V VL3V71BT101 28 ST UNREG ST UNREG D410 R485 (3V) 30 ACV UNREG IC405 16 BL UNREG BL UNREG 18 TIMER CLOCK CD-262 BOARD BATT UNREG (SEE PAGE 4-30) 17 Q102 CN101 CN301 38 D1.8VS IC406 IC402 CAM 15V CAM 15V 14 5 40 EEPROM RESET IC301 39 D1.8VP (SEE PAGE 4-30) (SEE PAGE 4-29) Q103, 105

CCD

41 CAM DD ON SWITCHING IMAGER PANEL –15V CAM 15V CA15V (SEE PAGE 4-8) CAM –7.5V CAM –7.5V CAM –7.5V CAM –7.5V CAM –7.5V S50 1 18CAM 15V 29 Q104 IC252 IC253 IC301 IC302 IC303 IC101 IC102 DA/AD CAMERA DSP, V ENCODER, TIMING CONVERTER AUDIO AMP MEMORY CONTROL 64M SDRAM 64M SDRAM A/D CONVERTER (SEE PAGE 4-15) (SEE PAGE 4-16) GENERATOR LENS UNIT (SEE PAGE 4-22) (SEE PAGE 4-23) (SEE PAGE 4-24) (SEE PAGE 4-17) (SEE PAGE 4-17)PANEL 13.2V (SEE PAGE 4-19) TO 21 PANEL 6.5V DD-141 BOARD 23 CN183 CN852 24 CAM P5V CAM P5V Q182 F SENS VCC (SEE PAGE 3-16) 7 VCC26 Z SENS VCC Q253 FB304 19 VCC20 CAM SP5V L303 22 FB301 L254 XLENS RST LED 42 A3.2V A3.2V FB302 27 PANEL 3.2V Q189, 190 DAC ENBD1.8VP D1.8VP CONTROL SWITCH 33 CAM 3.2V CAM 3.2V BLOCK 35 (ZOOM/POWER SW) D1.8VS D1.8VS CN708 (SEE PAGE 4-29) 30 D3.2V D3.2V D3.2V L183 D3.2V 32 4 D3.2V L185 L181 IC507 IC504 IC505 IC501 IC503 IC182 IC183 IC184 IC185 IC186 SHUTTER/FOCUS ZOOM MOTOR IRIS HALL EEPROM FLASH ROM SDRAM MC CAM CLOCK EVRMOTOR DRIVE DRIVE DRIVE AMP CN707 (SEE PAGE 4-27) (SEE PAGE 4-28) (SEE PAGE 4-27) (SEE PAGE 4-26) (SEE PAGE 4-26) (SEE PAGE 4-20)(SEE PAGE 4-19) (SEE PAGE 4-19) (SEE PAGE 4-19) (SEE PAGE 4-19) D3.2V 3 D3.2V

CONTROL SWITCH

CN702 CN801 BL UNIT BLOCK BL UNREG PD-127 BOARD (MODE SW) 3 3 BL UNREG LCD901 (SEE PAGE 4-29) CN701 CN802 CN901 PANEL –15V PANEL –15V PANEL –15V VSS119PANEL 13.2V PANEL 13.2V PANEL 13.2V VGH221COLOR PANEL 6.5V PANEL 6.5V LCD33PANEL 3.2V PANEL 3.2V L801 UNIT55PANEL 4.9V PANEL 4.9V D3.2V 2566PANEL 4.9V L903 A4.9V PANEL 4.9V VSH414412 43 VSH 2 IC801 IC802 IC901 IC902

TIMING

I/O EXP LCD DRIVE GENERATOR COM AMP (SEE PAGE 4-33) (SEE PAGE 4-34) (SEE PAGE 4-35) (SEE PAGE 4-35) 3-17 3-18 E, Yellow Cyan Green Yellow White Cyan Magenta Green Red White Blue Magenta Red Blue

DSC-S30/S50 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For printed wiring boards) (Measuring conditions voltage and waveform) • b: Pattern from the side which enables seeing. • Voltages and waveforms are measured between the (The other layers’ patterns are not indicated) measurement points and ground when camera shoots • Through hole is omitted. color bar chart of pattern box. They are reference values • Circled numbers refer to waveforms. and reference waveforms. * • There are few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used) isn’t mounted in this model. • Voltage values change depending upon input impedance • Chip parts. of VOM used.) Transistor DiodeC65445645123331. ConnectionBE123321321543212121Pattern box (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50 V or less are not indicated except for electrolytics and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. L New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 Front of the lens 22U 10UH TA A 2520 L=About 90cm Kinds of capacitor Temperature characteristics 2. Adjust the distance so that the output waveform of Fig. External dimensions (mm) a and the Fig. b can be obtain. • Constants of resistors, capacitors, ICs and etc with XX H indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/RECABA=BBA• 2: non flammable resistor Fig. a (Video output terminal output waveform) • 1: fusible resistor • C: panel designation • A: B+ Line * Color bar chart • B: B– Line * picture frame • J : IN/OUT direction of (+,–) B LINE. * Monitor TV • C: adjustment for repair. * picture frame • Circled numbers refer to waveforms. * * Indicated by the color red. Note : The components identified by mark 0 or Fig.b (Picture on monitor TV) dotted line with mark 0 are critical for safety. Replace only with part number specified. When indicating parts by reference number, please include the board name. Note : Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4-1,

BACK LIGHT

CN901 24P CLD 24 SPD 23 CTR 22 EX3 21 EX2 20 VB12 19

BL UNIT RES 18

TST 17 VR 16 VG 15 VB 14 GND 13 VSH 12 COM 11 VGL 10 VSS 9 MO2 8 MO1 7 GPCK 6 SPS 5 CLS 4 VCC 3 VSH 2 VGH 1

YP-051 HARNESS YP-052 HARNESS

CN709 18P N.C 1 N.C 2 N.C 3 REG_GND 4 CN183 26P XCPC_IN 5 26 IA N.C 6 25 IB HSY 7 24 IA PANEL_COM 8 23 IB VG 9 22 TEMP_COM (GND) UNREG 10 21 TEMP_OUT LANC_IN 11 20 Z_SENS_RST LANC_OUT 12 19 Z_SENS_VCC N.C 13 18 Z_SENS_GND RF7 14 17 ZOOM_A TXD 15 16 ZOOM_B RXD 16 15 ZOOM_B RESET 17 14 ZOOM_A VDD 18 13 DRIVE- 12 DRIVE+ CN710 2P 11 BIAS+ MIC SIG 1 10 HALL+ MIC GND29BIAS- CN712 2P 8 HALL- SP + 1 7 F_SENS_VCC SP - 2 6 F_SENS_RST 5 F_SENS_GND CN712 2P 4 FOCUS_A SP + 1 3 FOCUS_B

CCD IMAGER SP - 2

2 FOCUS_B 1 FOCUS_A CN706 10P XSTB_FULL 10 STROB_ON 9 UNREG 8 TALLY 7 PHOTO_TR_OUT 6 UNREG_GND 5 A_4.9V 4 POP_UP_ON 3 STRB_PHOTO_ON 2 STB_CHARGE 1 CN301 18P CN101 18P GND/TEMP 18 18 GND/TEMP RG 17 17 RG CN708 6P H2 16 16 H2 ZOOM_SW_AD 6 H1 15 15 H1 NC 5 CAM_-7.5V 14 14 CAM_-7.5V D_3.2V 4 VSUB_CONT 13 13 VSUB_CONT NC 3 VSHT 12 12 VSHT GND 2 V4 11 11 V4 XPER_SW 1 V3A 10 10 V3A V3B99V3B V288V2 V1A77V1A V1B66V1B GND55GND GND44GND CN707 6P CCD_OUT33CCD_OUT XSHTR_SW 6 GND22GND GND 5 CAM_15V11CAM_15V XSHTR_LOCK_SW 4 D_3.2V 3 XCAM/PB_SW 2 MOVIE/XSTILL_SW 1

DSC-S30/S50

4-1. FRAME SCHEMATIC DIAGRAMS

FRAME SCHEMATIC DIAGRAM (1/2)

12345678910 11 12 13 14 15 16 17 18

A CONTROL LCD901 SWITCH CONTROL PANEL UNIT CPC FLASH UNIT BLOCK SWITCH

(COLOR LCD) (FOR CHECK) S50 S30 ZOOM/ BLOCK

POWER_SW (MODE_SW)

MIC901 SP901 BZ901 S901 S903 MICROPHONE SPEAKER

B POWER MOVIE STILL PLAY

S902 (ZOOM) S904 (SHUTTER) W T CN802 14P CN701 14P PANEL_-15.3V11PANEL_-15.3V PANEL_13.2V22PANEL_13.2V PANEL_6.5V33PANEL_6.5V

C PANEL_4.9V44PANEL_4.9V

PANEL_3.2V55PANEL_3.2V D_3.2V66D_3.2V PANEL_COM77PANEL_COM HSY88HSY VG99VG ND901 CN851 20P REG_GND 10 10 REG_GND 20 N.C REG_GND 11 11 REG_GND

D 19 BL_HIGH PD-127 BOARD PANEL_Y 12 12 PANEL_Y

18 BL_HIGH PANEL_R-Y 13 13 PANEL_R-Y 17 N.C PANEL_B-Y 14 14 PANEL_B-Y 16 N.C SY-58 BOARD (1/2) 15 N.C CN801 12P CN702 12P 14 N.C BL_GND11BL_GND 13 N.C BL_GND22BL_GND 12 N.C BL_UNREG33BL_UNREG

E 11 N.C BL_ON44BL_ON

10 N.C BL_LED_ON55BL_LED_ON 9 N.C PANEL_PWM66PANEL_PWM 8 N.C XHI_SCK77XHI_SCK 7 N.C HI_SO88HI_SO 6 N.C XCS_PANEL_D/A99XCS_PANEL_D/A 5 LED PANEL_V 10 10 PANEL_V 4 LED_GND

F HDO 11 11 HDO3 BL_LOW

REG_GND 12 12 REG_GND 2 BL_LOW 1 UNREG_GND

G FP-021 FLEXIBLE BOARD FP-023 FLEXIBLE BOARD H IC301 LENS UNIT

M901 M902 FOCUS MOTOR ZOOM MOTOR

IMMCD-262 BOARD FRAME (1/2)

4-3 4-4, 1 10 CN703 7P CN101 7P KEY_AD117KEY_AD1 KEY_AD226KEY_AD2 KEY_AD335KEY_AD3 CN852 80P CN711 80P REG_GND44REG_GND 1 REG_GND REG_GND 2 79 REG_GND REG_GND 80 XCHG_LED53XCHG_LED 3 REG_GND REG_GND 4 77 REG_GND REG_GND 78 D_3.2V62D_3.2V 5 AU_OUT REG_GND 6 75 REG_GND AU_OUT 76 VL_3V71VL_3V 7 AU_GND USB_D+OUT 8 73 USB_D+OUT AU_GND 74 9 XAU_LINE_MUTE USB_D-OUT 10 71 USB_D-OUT XAU_LINE_MUTE 72 11 REG_GND REG_GND 12 69 REG_GND REG_GND 70 13 C_OUT USB_TXENL 14 67 USB_TXENL C_OUT 68 15 REG_GND USB_XVDATA 16 65 USB_XVDATA REG_GND 66 17 Y_OUT REG_GND 18 63 REG_GND Y_OUT 64 19 REG_GND USB_D+IN 20 61 USB_D+IN REG_GND 62 21 CNT_Y USB_D-IN 22 59 USB_D-IN CNT_Y 60 23 REG_GND REG_GND 24 57 REG_GND REG_GND 58 25 CNT_C USB_SUSPND 26 55 USB_SUSPND CNT_C 56 27 VOUT_ON USB_D+PULLUP 28 53 USB_D+PULLUP VOUT_ON 54 29 REG_GND LANC_JACK_IN 30 51 LANC_JACK_IN REG_GND 52 31 N.C. EXT_STRB_ON 32 49 EXT_STRB_ON N.C. 50 33 N.C. USB_DET 34 47 USB_DET N.C. 48 35 REG_GND AV_JACK_IN 36 45 AV_JACK_IN REG_GND 46 37 A_3.2V A_4.9V 38 43 A_4.9V A_3.2V 44 39 A_3.2V A_4.9V 40 41 A_4.9V A_3.2V 42 41 D_1.8VS D_1.8VP 42 39 D_1.8VP D_1.8VS 40 43 D_1.8VS D_1.8VP 44 37 D_1.8VP D_1.8VS 38 45 D_3.2V CAM_3.2V 46 35 CAM_3.2V D_3.2V 36 47 D_3.2V CAM_3.2V 48 33 CAM_3.2V D_3.2V 34 49 D_3.2V CAM_-7.5V 50 31 CAM_-7.5V D_3.2V 32 51 ST_UNREG CAM_15V 52 29 CAM_15V ST_UNREG 30 53 ST_UNREG PANEL_3.2V 54 27 P ANEL_3.2V ST_UNREG 28 55 CAM_P_5V PANEL_4.9V 56 25 PANEL_4.9V CAM_P_5V 26 57 CAM_P_5V PANEL_6.5V 58 23 PANEL_6.5V CAM_P_5V 24 59 SP_5V PANEL_13.2V 60 21 PANEL_13.2V SP_5V 22 61 SP_5V PANEL_-15V 62 19 PANEL_-15V SP_5V 20 63 BL_UNREG BATT_UNREG 64 17 BATT_UNREG BL_UNREG 18 65 BL_UNREG N.C. 66 15 N.C. BL_UNREG 16 67 N.C. LCD_DD_ON 68 13 LCD_DD_ON N.C. 14 69 FAST_CHARGE SYS_DD_ON 70 11 SYS_DD_ON FAST_CHARGE 12 71 INIT_CHARGE_ON REG_GND 72 9 REG_GND INIT_CHARGE_ON 10 73 LANC_DC LANC_SIG 74 7 LANC_SIG LANC_DC 8 75 XLANC_PWR_ON REG_GND 76 5 REG_GND XLANC_PWR_ON 6 77 REG_GND REG_GND 78 3 REG_GND REG_GND 4 79 REG_GND REG_GND 80 1 REG_GND REG_GND 2 CN202 4P 4 GND 3 D+ 2 D- 1 VCC

DSC-S30/S50 FRAME SCHEMATIC DIAGRAM (2/2)

12345678910 11 12 13 14 15 16 17 18 19

A

S101 S104 S105 S106 (CONTROL BUTTON) PROGRAM AE CN201 16P PROGRAM AE/ PANEL VOLUME + UP/DOWN REG_GND 1 A_OUT 2 REG_GND 3 S102 V_OUT 4

B DISPLAY AV_JACK_IN 5S107

FOCUS N.C. 6 N.C. 7 N.C. 8 S103 D102 SW-339 BOARD JK-194 BOARD N.C. 9 S108 (FLASH) N.C. 10 PROGRAM AE/ N.C. 11 (FLASH) VOLUME - USB_DET 12 REG_GND 13

C BT101(LITHIUM BATTERY) D+ 14

D- 15 S109 REG_GND 16

LCD

BACK LIGHT S110

PANEL

ON/OFF

D FP-025 FLEXIBLE BOARD J201 E A/V OUT USB

DSC-S50

VIDEO OUT

DSC-S30

F SY-58 BOARD (2/2)

D411 (BATT CHARGE) CN003 14P CN704 14P BATT/XEXT 1 14 BATT/XEXT CN004 10P D412BATT_SIG 2 13 BATT_SIG (POWER)

G KJ-11 BOARD1 VSS A_4.9V 3 12 A_4.9V

2 BS ACCESS_LED 4 11 ACCESS_LED 3 VCC S301REG_GND 5 10 REG_GND

SK-100 PANEL4 DIO MS_BS69MS_BS CN713 2P REVERSEHARNESS MEMORY STICK 5 N.C MS_DIO78MS_DIO KEY_AD0 1

6 INT D002 GND_GARD87GND_GARD REG_GND27N.C ACCESS LED(RED) XMS_IN96XMS_IN 8 SCLK GND_GARD 10 5 GND_GARD

H 9 VCC MS_SCLK 11 4 MS_SCLK

10 VSS GND_GARD 12 3 GND_GARD MS_VCC 13 FP-024 2 MS_VCC REG_GND 14 FLEXIBLE 1 REG_GND

BOARD I BOARD TO BOARD CONNECTORMS-50 BOARD

CN851 16P REG_GND 16 CN005 14P CN001 14P D- 15 CN001 3P FAST_CHARGE11FAST_CHARGE D+ 14

J 1 ACV_UNREG INIT_CHARGE_ON22INIT_CHARGE_ONDC IN 3P REG_GND 132 ACV_GND REG_GND33REG_GND

USB_DET 12 3 BATT/XEXT REG_GND44REG_GND N.C. 11 REG_GND55REG_GND N.C. 10 REG_GND66REG_GND FP-026 FLEXIBLE BOARD N.C. 9 UNREG5(ST_UNREG) 7 7 UNREG5(ST_UNREG) UNREG5(ST_UNREG) 8 YP-052 HARNESS N.C. 8 8 UNREG5(ST_UNREG) BT901 N.C. 7 BATTERY TERMINAL UNREG4(BL_UNREG/ACV) 9 9 UNREG4(BL_UNREG/ACV) N.C. 6

K UNREG3(TRANS/A4.9) 10 10 UNREG3(TRANS/A4.9)CN002 3P AV_JACK_IN 5

UNREG3(TRANS/A4.9) 11 11 UNREG3(TRANS/A4.9) 1 BATT_UNREG V_OUT 4

S UNREG2(D3.2/1.8V) 12 12 UNREG2(D3.2/1.8V)2 BATT_SIG REG_GND 3

UNREG2(D3.2/1.8V) 13 13 UNREG2(D3.2/1.8V) 3 BATT_GND A_OUT 2 UNREG1(BATT_UNREG) 14 14 UNREG1(BATT_UNREG) REG_GND 1

DD-141 BOARD L FRAME (2/2)

4-5 4-6, CN301 18P 18 GND/TEMP 17 RG 16 H2 15 H1 14 CAM_-7.5V 13 VSUB_CONT 12 VSHT 11 V4 10 V3A 9 V3B 8 V2 7 V1A 6 V1B 5 GND 4 GND 3 CCD_OUT 2 GND 1 CAM_15V S2/P0 H2 V4 S2.7/P0 S-1.7/P0 H1 V3A S2.6/P0 S-1.7/P0 RG V3B S-0.2/P0 VL V2 S-7.4/P0 S8.4/P0 S-0.2/P0 R309 CSUB V1A * S8.2/P0 S-0.2/P0VSHT V1B GND GND VDD VOUT S10.5/P0

DSC-S30/S50

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • See page 4-49 for waveforms.

CD-262 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM

– Ref. No.: CD-262 board; 2,000 series – • For Printed Wiring Board. 123456789• CD-262 board is four-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. SY-58 BOARD (2/8)CN101 CD-262 BOARD • There are few cases that the part isn't mounted in this model (THROUGH THEA FP-023 FLEXIBLE) (SEE PAGE 4-17) CCD IMAGER is printed on this diagram. -REF.NO.:2,000 SERIES- • Chip transistor XX MARK:NO MOUNT NO MARK:STILL/PB MODE C S:STILL MODE P:PB MODE

B

B E

C

Q302 2SC4178-F13F14-T1 S14.8/P0 L301 R307

D 100uH 0

C307 0.1u C309 16V 10p C310 S-1.7/P0 S11.4/P0 XX12345678R306

IC301

CCD IMAGER45IC301 3

E ICX202BQ-13:S30ICX284AQ-13:S50

*R302,303 D301 33:S30 1 MA111-(K8).S0 15:S50 2 16 15 14 13 12 11 10 9R302 S14.8/P0 * R303 *

F R30147

C311 1u 25V C308 R305 0.1u * C304 C305 16V SIGNAL PATH 0.1u 0.1u C312 FB301 50V 16V 2200p S9/P0 VIDEO R304 SIGNAL 6.8k:S30 *R305 C302 C303 2.2k:S50 1M:S30 22u 0.01u C306 220k:S50 Y/CHROMA 16V 16V 0.1u C301 0.1 16V *R30910u R308 47:S30

G 20V 100k 22:S50 REC

Q301 UN9213J-(K8).SO

Precautions for Replacement of CCD Imager

• The CD-262 board mounted as a repair part is not equipped with a CCD imager.

When replacing this board, remove the CCD imager from the

old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts

nor exposed to strong light.

CCD IMAGER CD-262 4-7 4-8

, 10 1

DSC-S30/S50 MS-50 (FU, MEMORY STICK) PRINTED WIRING BOARD AND SHEMATIC DIAGRAM

– Ref. No.: MS-50 board; 2,000 series – • For Printed Wiring Board. 12345678910 11 12 13 • There are few cases that the part isn't mounted in this model is printed on this diagram. MS-50 BOARD • Chip transistor

A FU/MEMORY STICK (FU/MS BLOCK) C -REF.NO.:2,000 SERIES-

XX MARK:NO MOUNT NO MARK:STILL/PB MODE

B E CN005 14PCN001 3P LF001

1 FAST_CHARGE ACV_UNREG 1 R005 2 INIT_CHARGE_ONB DC IN ACV_GND 2 D003 10MA8082-(K8).S0 R0063216 3 REG_GND BATT/XEXT 3 8.2 1k FB002 R001 D001MA8082-(K8).S0 Q002,003 Q003 4 REG_GND R008 1k BATTERY 2SB1122-ST-TD XX CHARGE/DISCHARGE 5 REG_GND Q002 SI4963DY-T1 7.6 F005 1.4A/32V 6 REG_GND C001 C002 R009 7.8 8.2 DD-141 BOARD (1/3) XX XX07UNREG5(ST_UNREG) CN001 2 D006 LND001 (THROUGH THE1SS357-TPH3 F004 1.4A/32V 8 UNREG5(ST_UNREG)7 YP-052 HARNESS) FLAME_GND818.3 9 UNREG4(BL_UNREG/ACV) (SEE PAGE 4-43) 8 R007 8 6800 F003 1.4A/32V 10 UNREG3(TRANS/A4.9)3.2

C 0 11 UNREG3(TRANS/A4.9)R003 3 5

BT901 470k BATTERY 6 F002 1.4A/32V 12 UNREG2(D3.2/1.8V)4 TERMINAL 13 UNREG2(D3.2/1.8V) Q004 CN002 3P D005 7.8 UN9213J-(K8).SO 14 UNREG1(BATT_UNREG) MA8120-TX SWITCHING F001 BATT_UNREG 1 1.4A/32V C005 S XXBATT_SIG 2 FB001 C0040.022u BATT_GND 3 7.8 R004 1M 0 1608D Q001 SSM3K03FE(TPL3)

SWITCHING E

R002 1k D002 CN003 14P CL-270HR-C-TS

F BATT/XEXT 1 (ACCESS LED(RED))

BATT_SIG 2 C006 MEMORY STICK A_4.9V 3 0.1u CN004 10P ACCESS_LED41VSS REG_GND52BS SY-58 BOARD (6/8) MS_BS63VCC CN704 (THROUGH THE MS_DIO74DIO FP-024 FLEXIBLE) GND_GARD85N.C

G (SEE PAGE 4-25) XMS_IN96INT

GND_GARD 10 7 N.C MS_SCLK 11 8 SCLK GND_GARD 12 9 VCC MS_VCC 13 10 VSS REG_GND 14 C003 0.1u C007 05 2200p

H The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que

Replace only with part number specified. par une piéce portant le numéro spécifié. FU/MEMORY STICK

4-9 4-10 MS-50,

DSC-S30/S50

• For Printed Wiring Board. • PD-127 board is four-layer print board. However, the patterns PD-127 (TG, LCD) PRINTED WIRING BOARD of layers 2 to 3 have not been included in the diagram.• There are few cases that the part isn't mounted in this model – Ref. No.: PD-127 board; 2,000 series – is printed on this diagram. • Chip transistor

C

B E

TG, LCD PD-127 4-31 4-32

, CN851 20P UNREG_GND 1 BL_LOW 2 C802 0.1u BL_LOW 3 LED_GND 4 LED 5 N.C 6 N.C 7 N.C 8 N.C 9 N.C 10 24 23 22 21 20 19 18 17 16 15 14 13 N.C 11 N.C 12 N.C 13 N.C 14 N.C 15 N.C 16 N.C 17 BL_HIGH 18 BL_HIGH 1912345678910 11 12 N.C 203214548 47 46 45 44 43 42 41 40 39 38 37 COM_ADJ PICTURE COM_BLK_LVL 3.1 1.9 Y/CR/XRGB_SW COM_AMP 0.8 1.1 AGC_FIL GAMMA2 0.8 AGC_OUT GAMMA0 2.3 BRT_R AGC_LVL SUB_BRT_R 1.2 2.3 BRT_B COLOR SUB_BRT_B 2.4 AMP H_FIL_IN RGB_AMP 2 2.4 FRPV G/Y FRP 2 2.4 FRPT R/R-Y/CR COM_FRP B/B-Y/CB OUT_LIM 4.9 H_FIL VSH 0 6.5 REG_OUT VCC2 13 14 15 16 17 18 19 20 21 22 23 24

COLOR DSC-S30/S50 PD-127 (LCD DRIVE) SCHEMATIC DIAGRAM • See page 4-49 for waveforms.

12345678910 11 12 13 14 15 16

A PD-127 BOARD (1/2) ND901 BACK LIGHT LCD DRIVE (RGB BLOCK)

-REF.NO.:2,000 SERIES-

XX MARK:NO MOUNT NO MARK:STILL/PB MODE B C BL UNIT

JL004 L803 4.7uH C817 C818 C811 22u 22u R813 10u 16V 16V JL005 R808 R812 R817 22k 47k 15k 12k 10V C8130.1u L801 R809 R814 R818 100uH 12k 33k 39k C812

D L802 10u

10uH 10V IC801 C807 C808 MB40D001PFV-G-BND-ER 47u 0.1u P_4.9VC801 6.3V 0.1u 3.1 3.1 VDD P_MUTE 3.2 3.1 VCC BRT_TST CN801 12P H_REV 3.2 36 35 34 33 32 31 30 29 28 27 26 25 H_REV BL_LEVEL BL_GND 1 V_REV 3.2 1.8 V-COM

E BL_GND 2 V_REV V-COM 2

BL_UNREG 3 NTSC 3.2 1.2 VCO JL001 NTSC VCO BL_ON 4 SY-58 BOARD (8/8) JL002 COMTST 0 0.9 COM_ADJ 2.5BL_LED_ON 5 COMTST COM_ADJ COM_BLK B_OUT VB CN702 JL003 3.2 2 C814 (THROUGH THE PANEL_PWM 6 2.9 2.3 AMP C806 XTEST B_DC_DET CLK RGB_AMP 0.1u 1u YP-051 HARNESS) 1.9 2.5XHI_SCK 7 BRIGHT 3 G_OUT VG (SEE PAGE 4-29) 0.1222.1 C815 HI_SO 8 SI CONT CONTRAST 1 G_DC_DET 1uCOM-O 2.5 XCS_PANEL_D/A 9 1.8 BRT_B COM_OUT R_OUT VR

F SO BRT_B R803 2PANEL_V 10 PANEL_V10SUB_CON_B IC802 4 R_DC_DET C8161u COM-O

3 2.3 BRT_R COM-O HDO 11 HDO PD-127 BOARD XEN BRT_R SUB_CON_R LCD DRIVE GND1 (2/2) 3.1 IC802 REG_GND 12 3.1 1.1 COLOR VCC1 IR3Y37A4 GND2 FRPV VDDA COLOR FRPV 4 OSD_B SYNC_OUT C819 FRPT PD-127 BOARD 2200p 1.9 3.1 FRPTVSS BRIGHT OSD_G 7 SYNC_IN (2/2)5 4.6 LND801 R805 OSD_R EXT_BGP0 P_XHD4.9 STATIC_GND BLACK_IN86SYNC_SEPD801 MA111-(K8).S0 IC801

G I/O EXP (EVR)

INB COMTST COMTST CN802 14P VCC NTSC

NTSC

PANEL_-15.3V 1 PANEL_-15.3V INA V_REV12345678910 11 12 V_REV PANEL_13.2V 2 PANEL_13.2V OUT H_REV 2 GND H_REV PANEL_6.5V 3 V-COM PD-127 BOARD IC803 V-COM PANEL_4.9V 4 PANEL_4.9V (2/2) XX VCO

VCO

PANEL_3.2V 5 PANEL_3.2V

H SY-58 BOARD (7/8) D_3.2V 6 R806 R810

C809 R821 XX 0

XX

6.3V 10k CN701 PANEL_COM 7 PANEL_COM 3 R807 R819 R820 (THROUGH THE C810HSY XX XX 0.1u YP-052 HARNESS) HSY 8 PD-127 BOARD 100k (2/2) REG_GND (SEE PAGE 4-27) VG 9 W_MSK REG_GND 10 REG_GND 11 FB801 C803 0.01u PANEL_Y 12 FB802 C804 0.01u PANEL_R-Y 13 FB803 C805 0.01u

I PANEL_B-Y 14 SIGNAL PATH VIDEO SIGNAL CHROMA Y REC J PB The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que LCD DRIVE 4-33 Replace only with part number specified. par une piéce portant le numéro spécifié. 4-34 PD-127 (1/2), R908 VCO 680k D902 1T369-01-T8A 48 47 46 45 44 43 42 41 40 39 38 37 2.4 4.9 BLKI P16 2.4 BLKO VSEPC 2.5 3 BGPO P15 4.6 4.9 HSY MUT 2.5 VSY PDP VIN GND 4.9 GND VDD43214.9 SYNO TST2 0 4.9 WIDOV TST1 2.4 WIDOT OSCI 2.4 2.3 FRPV OSCO 2.45678FRPT TESTO 13 14 15 16 17 18 19 20 21 22 23 24 Q902 2SB1462J-QR (K8).SO COM-O V_COM PANEL_COM C915 0.01u C918 C917 1u 0.1u R961 47 VB R960 47 VG R962 47 VR

DSC-S30/S50 PD-127 (TIMING GENERATOR) SCHEMATIC DIAGRAM • See page 4-31 for PD-127 printed wiring board. • See page 4-49 for waveforms.

12345678910 11 12 13 14

A PD-127 BOARD (2/2) TIMING GENERATOR (TG BLOCK)

-REF.NO.:2,000 SERIES-

XX MARK:NO MOUNT NO MARK:STILL/PB MODE

L901 10uH

B PANEL_13.2V2 PD-127 BOARD (1/2)

PANEL_-15.3V L902 IC902 R929 10uH NJM062V(TE2) 100k 13.49 1.7 Q903 R935 3.9 13.4 2SD2216J-QR 33k OUT1 VCC+ (K8).SO R911 R925 VB 10k C909 2.5 1.4 100k 1.4 VB 0.1u IN1- OUT2 VG R914 C911 1.3 VG 1M 560p 2.4 0.4 1.4 R936 4 PD-127 BOARD (1/2) VR R916 IN1+ IN2- -10.2 C914 22kVR C907 68k -10.2 0.4 Q901 Q904 6.8u0.001u VCC- IN2+ 2SD2216J-QR 1 16V R937 C916

C P_4.9V 2SB1462J-QR 1u (K8).SO 1 (K8).SO 33k 35V

R917 L903 68k IC902 R932 C913 D90310uH L905 100k-10.2 1u MA8047-H-TX 2 PD-127 BOARD (1/2) PANEL_4.9V 6.8uH R938 COM AMP R912 R926 R928 R933 22k 33k 1M R915 33k 100k 22k C902 C905 C901 R909 R922 3.3u 0.1u XX 120k C906 C908 R918 4700 Q901-904 20V 6.3V 0.1u 82p 47k R921 COM DRIVE4700 4 PD-127 BOARD (1/2) REG_GND

D C910XX

CN901 24P LCD901 PANEL_COM 3 PD-127 BOARD (1/2) PANEL_COM 24 CLD V-COM C904 V-COM 0.1u 23 SPD COM-O 4 PD-127 BOARD (1/2) COM-O 22 CTR

VCO

VCO R9130 21 EX3E 1 PD-127 BOARD (1/2) PANEL_V 36 35 34 33 32 31 30 29 28 27 26 25 20 EX2 R904 19 VB12 47k 18 RES 2 PD-127 BOARD (1/2) PANEL_3.2V 17 TST R905 47k 11 R9340 16 VR2.8 2.2 COLOR 1 PD-127 BOARD (1/2) HDO SYNI 10 CLD 15 VG LCD 0.5 UNIT SYNC SPD 14 VB 4.9 2.4

F WIDE CTR 13 GND0

PDPC EX3 12 VSH 3.2 4.9 NTSC NTPC1 EX2 11 COM TESTI IC901 TESTO 10 VGL 4.9 2.4 TEST LCD TIMING GENERATOR RES 9 VSS 3.2 IC901 4.9 V_REV VREVC R910 100k LZ9GH234 MODE2 8 MO2 C903 4.9 4.9 0.1u TESTI MODE1 7 MO1 3.2 0 H_REV HREVC EX1 6 GPCK

G COMTST COMTST 13

4.8 SPS 5 SPS 4.8 3.9 LOWI CLS 4 CLS 12 14 3 VCC 2 VSH 4 PD-127 BOARD (1/2) 1 VGH12345678910 11 12

H

R919 R920 68k 33k SIGNAL PATH C912 VIDEO SIGNAL 82p

CHROMA

P_XHD 3 PD-127 BOARD (1/2) HSY REC

I W_MSK

4 PD-127 BOARD (1/2) FRPV PB

FRPT TIMING GENERATOR PD-127 (2/2) 4-35 4-36

,

DSC-S30/S50

• For Printed Wiring Board. • There are few cases that the part isn't mounted in this model JK-194 (USB, A/V OUT), KJ-11 (PANEL REVERSE), SW-339 (SWITCH) PRINTED WIRING BOARDS is printed on this diagram. – Ref. No.: JK-194 board; 2,000 series, KJ-11 board; 3,000 series, SW-339 board; 2,000 series – • Chip Diode214-38

USB, A/V OUT/PANEL REVERSE/SWITCH4-37 JK-194 KJ-11 SW-339

, D201 MA4Z082WA-(TX).SO D210 RD5.1UM-T1B D211 RD5.1UM-T1B

DSC-S30/S50

JK-194 (USB, A/V OUT), KJ-11 (PANEL REVERSE), SW-339 (SWITCH) SCHEMATIC DIAGRAMS • See page 4-37 for JK-194, KJ-11, SW-339 printed wiring boards. 12345678910 11 12 13 14 15 16 17 18

A SW-339 BOARD JK-194 BOARD SWITCH USB,A/V OUT

-REF.NO.:2,000 SERIES-

B -REF.NO.:2,000 SERIES- S106S104

R104 PANEL 15k PROGRAM AE UP/DOWN R113 R201 33k 330k LF203 CN202 R212 4P 220k341VCC212D- USB S101 R106 (CONTROL) 2700 3 D+CN2013416P 4 GND

C LND101 R111 R114 R116 2 14700 6800 33k REG_GND 16 LF204

STATIC_GND 8 UP SET D- 15 C201 D205172200p MA111-(K8).S0R102 D+ 14 1800 S102 S105 S108 S110 LEFT RIGHT REG_GND 1326DISPLAY PROGRAM AE/ PROGRAM AE/ PANEL ON/OFF D203 VOLUME + VOLUME - USB_DET 12 MA4Z082WA-(TX).SO COMMON DOWN N.C. 11 D10135C101 3 DD-141 BOARD (3/3) N.C. 10MA111-(K8).S0 R107 S103 CN851

D 2200p D104 2700 (THROUGH THE N.C. 9

D103 MA4Z082WA-(TX).SO FP-026 FLEXIBLE) N.C. 8 RD8.2UM-T1B S107 S1092 1 (SEE PAGE 4-48) CN101 R103 1800 (FLASH) FOCUS BACK LIGHT N.C. 7 7P BRIGHT/NORMAL N.C. 6 R2021k R109 R112 R115 KEY_AD1 7 4700 6800 33k AV_JACK_IN 5 KEY_AD2 6 V_OUT434SY-58 BOARD (8/8) CN703 KEY_AD3 5 REG_GND321(THROUGH THE REG_GND 4 A_OUT 2 LF201 J201 FP-025 FLEXIBLE) (SEE PAGE 4-29) XCHG_LED 3 REG_GND 1 DSC-S50E FLASH LED(AMBER) R213D_3.2V 2 D102 0 A/V SML-311YTT86 VL_3V 1 OUT R101 D206 DSC-S30 220 MA111-(K8).S0 BT101 VIDEOOUT LITHIUM LND201

BATTERY

STATIC_GND C202 D207 2200p MA4Z082WA-(TX).SO

F LND202

STATIC_GND D209 MA4Z082WA-(TX).SO

KJ-11 BOARD PANEL REVERSE G -REF.NO.:3,000 SERIES-

LND301 KEY_AD0 KEY_AD0 S301 SY-58 BOARD (1/8) CN713 PANELREG_GND REVERSE (THROUGH THE SK-100 HARNESS)

H (SEE PAGE 4-15) LND302REG_GND The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que

Replace only with part number specified. par une piéce portant le numéro spécifié.

4-39

USB, A/V OUT/PANEL REVERSE/SWITCHJK-194 KJ-11 SW-339 4-40

,

DSC-S30/S50

• For Printed Wiring Board. • DD-141 board is six-layer print board. However, the patterns DD-141 (DC/DC CONVERTER, VIDEO, USB) PRINTED WIRING BOARD of layers 2 to 5 have not been included in the diagram.• There are few cases that the part isn't mounted in this model – Ref. No.: DD-141 board; 1,000 series – is printed on this diagram. • See page 4-52 for printed parts location. • Chip transistor

C

B E 12 12 4-42

DC/DC CONVERTER, VIDEO, USB

4-41 DD-141, D005

XX

24 23 22 21 20 19 18 17 16 15 14 13 +IN C +IN B 2.5 2.5 R008 4700 -IN C -IN B 1.4 1.7 FB C FB B C008 0.022u 1.5 C007 0.022u DTC C DTC B 2.5 3.2 SCP:D SCP:A 3.2 1.5 +IN D +IN A 2.4 1.5 -IN D -IN A 2.5 1.8 R025 1k FB D FB A C015 0.022u 1.5 C014 4700p DTC D DTC A 2.5 CC1 CB1 7.3 8.4 CC2 CB2 8.5 7.1 CD1 CA1 37 38 39 40 41 42 43 44 45 46 47 4812348765C048 0.47u

DSC-S30/S50 DD-141 (DC/DC CONVERTER) SCHEMATIC DIAGRAM • See page 4-41 for DD-141 printed wiring board.

12345678910 11 12 13 14 15 16 17 18 19 20

DD-141 BOARD (1/3) A DC/DC CONVERTER (DD BLOCK) NO MARK:STILL/PB MODE

-REF.NO.:1,000 SERIES-

XX MARK:NO MOUNT

CN001 14P FAST_CHARGE 1 FAST_CHARGE 1 DD-141 BOARD (3/3) INIT_CHARGE_ON 2 INIT_CHARGE

B REG_GND 3 SYS_DD_ON

REG_GND 4 BATT_UNREG 2 DD-141 BOARD (3/3) TO REG_GND 5 LCD_DD_ON MS-50 BOARD CN005 REG_GND 6 (THROUGH THE UNREG5(ST_UNREG) 7 ST_UNREG YP-052 HARNESS) (SEE PAGE 4-10) UNREG5(ST_UNREG) 8 BL_UNREG UNREG4(BL_UNREG/ACV) 9 DD-141 BOARD (3/3) UNREG3(TRANS/A4.9) 10 1

C UNREG3(TRANS/A4.9) 11

UNREG2(D3.2/1.8V) 12 D_1.8VS L001 L002 D_1.8V UNREG2(D3.2/1.8V) 13 D_1.8VPC009 C013 C020 10uH 10uH 10u UNREG1(BATT_UNREG) 14 10u 10u16V 16V 16V REG_GND 2.05v R017 C011 CAM_15V 150k XX R033 0 L006 R006 15 13.2 20k R019 22uH R032 R034 15.05v 2 1.8V 15V PANEL13.2v 6800 PANEL_13.2VD C010 10kR007 00.022u 2 1.9 L010 R061 Q027 3600 R020 2200 Q009 1uH R057 100k 2SB1462J-QR(K8).SO C019212SB1122-ST-TD 33k B+ SWITCH LND001 R002 R009 R021 0.1u R0490 B+ SWITCH 1.2 14.4 4700 18k 47k STATIC_GND R010 R005 R022 Q004 39k 15k 47k FP107-TL R046 Q019,031,03347 R018 SWITCHING DRIVER Q031 LND002 R003 10k C032 C035 2SB1462J-XX 14R011 8.1 4.7u 0.2 22u QR(K8).SOR02335STATIC_GND 27k 4V68k 0.7 Q013 13.2 C052 1u R024 R055 2SD2216J- Q019 20V R012 4700 8.3C029 10k C016 R081 QR(K8).SO 13.1 2SD2216J-

E 2200 0.1u 4700 SWITCHING QR(K8).SO4.7u

C017 C021 12.7 470p 470p 12.7 Q0332SD2216J- R068 15.05V QR(K8).SO100k DC/DC CONVERTER 10.5V 8.9 6.6 PANEL6.5v PANEL_6.5V Q032 R064 2SB1462J- Q001 47k 8.2T001 D002 QR(K8).SO 2.5172SB1122-ST-TD L013 R058

F SWITCHING MA796-TX R047

B+ SWITCH 220uH R050 120k 8.74147k 10k 12 11 109876543218.713.1 R059 Q0288.3 0 D001 3.2 Q022R051 0 2SB1462J- 1SS357322SD2216J-3300 8.9 0.1 QR(K8).SO 8 -TPH3 0.6 0 QR(K8).SO C023 0.001u 4.4 8.4 C044 SCP:B CA2 4.7u 6.6 Q010 Q034 1 20V XX R048 2SD2216J- Q018 6.5 OSC IN VE A QR(K8).SO C053 22k R060 2.2u R001 8.1 R035 470 C034 SWITCHING UN9213J- Q025 R070 OSC FB OUT A 4.7u C043 (K8).SO 120k 6.1 2SD2216J- 4700 10k Q022,025,0281.2 4.7u SWITCHING R067 QR(K8).SO DRIVER RT CAM15V P5V Vcc OUT C037 47k 1.6484.7uCT OUTB2DD-141 BOARD (3/3)

G C024 0.001uC001 8.3 IC001 1.2 -10.5V R065 R069180p Vcc VE B 82k 10k

2.5 R036 V REF 2.5V DC CONTROL GND 680 R071 C002 IC001 0.9 R037 470 30k 0.1u 3.1 POW CONT VE C C051 MB3785APFV-G-BND-ER Q023 8.2 0.1u 0.4 2SB1462J- CTL B 4.9V 3.2V OUT C QR(K8).SO C003 7.9 C025 0.001u 4.95V C054 0.068u CTL C,D OUT D 0.1u C049 -0.2 10u 0 CT SCP 1.3 R038 470 L004 22uH Q016 Q017 16VVE D D003 D004 NDS356AP UN9113J-(K8).SO R072 2.5 8.1 B+ SWITCH SWITCHING Q020 SCP:C CD2 MA111-4.9 MA111- 4.9 2SB1462J- -10.3 22k (K8).S0 (K8).S0 C026 0.001u21L011 QR(K8).SO 1uH R052 4.9 4.9

H CAM_P_5V SP_5V 100k

-9.6 Q003 Q020,023,026 Q026 R073-9.8 CPH5701-TL C046R053 0 L014 3.1 DRIVER 2SD2216J- 68k 100k 0.022u QR(K8).SO25 26 27 28 29 30 31 32 33 34 35 36 SWITCHING 4.7uH C031 R062 2.4 6.5 4.7u C036 100k -10.3 -7.6 8.235033u CAM_-7.5V 10V CAM-7.5VC047 Q029 R082 Q014 10u 2SD2216J-3.2 C028 XX UN9213J-(K8).SO 10V QR(K8).SO8.3 4.7u SWITCHING R066 B+ SWITCH C005 C018 C022 100k Ref2.5v 0.001u 470p 470p

I 3.25v 3.24VR004 R013270k 4700 R026 L003 L012 R056 C050 0.3 Q024 R074

3900 3.2 22uH 1uH 15k 0.47u 18k PANEL_3.2V 2SB1462J- QR(K8).SO R07521R078 0 L009 A_3.2V 0 1600 4.7uH Q002 CAM_3.2V Q021 0.1 C004 R014 R027 2SB1462J- 0.022u CPH570110k 2700 -TL D_3.2V QR(K8).SO C055 -33.1 1u -34.1 R015 R028 SWITCHING L005 Q030 R076 390 15k8351uH -34.1 2SD2216J- 120k Q021,024 R063 QR(K8).SO DRIVER 100k B+ SWITCHC006 R016 C012 R029 R030 XX C027 C03010k XX 4700 0 8.3 4.7u C033 C042 PANEL_-15.3VJ 4.7u 2.2u 2.2u -33.1 -15.3 PANEL-15.3v 4.9v Q006 C038 PANEL_4.9V 2SB1122-ST-TD PANEL_4.9VR031 10u 0 B+ SWITCH 6.3V A_4.9V A_4.9V 8.3 4.9 L008 1uH CAM_P_5V 1 DD-141 BOARD (3/3) R054 100k 7.5 Q005,007,008 +4.9V REG 7.6 Q008 R045 2SB1462J- 10k QR(K8).SO PANEL_3.2V

K R039 C03910u A_3.2V 2 DD-141 BOARD (3/3)12k 0.5 10V CAM_3.2V

Q005 2.3 2.5 D_3.2V 1 DD-141 BOARD (3/3) 2SD2216J- QR(K8).SO 1.8 Q007 2SD2216J- R040 R042 QR(K8).SO R043 R044 39k 1500 1500 10k

L The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que

Replace only with part number specified. par une piéce portant le numéro spécifié. DC/DC CONVERTER DD-141 (1/3) 4-43 4-44

, CLAMPREF C-IN YIN GCTL/

PSAVE

GCTL V+2 /MUTE CLAMP V+1 D-CHGCONT V+1 GND VOUT GND VSAG

DSC-S30/S50 DD-141 (VIDEO) SCHEMATIC DIAGRAM • See page 4-41 for DD-141 printed wiring board. • See page 4-49 for waveforms.

12345678910 11

A DD-141 BOARD (2/3) VIDEO (VI BLOCK)

-REF.NO.:1,000 SERIES-

XX MARK:NO MOUNT NO MARK:STILL/PB MODE

VOUT_ON

B A_4.9V L801 Q806

47uH 2SD2216J-QR(K8).SO L802 REG 10uH 4.7 3 A_3.2V Q807 R811 2SB1462J-QR(K8).SO 22k SWITCH R812 3.6 C814 0.1u 47k 3.1 C820 C819 10u R805 100u R810 6.3V 10k 4V 68

C CNT_C V_OUT

CNT_Y 4.9 C_OUT C808 C818 0.1u 1.8 1.3 3 1.7 1.5 22u 6.3V 14 13 12 11 1098

D IC802

VIDEO AMP IC80212NJM2568V(TE2) 12345673DD-141 BOARD (3/3) 4 DD-141 BOARD (3/3) 1.9 1.5 1.3 1.2 0

E

C809 1u Y_OUT R804 10k R807 R809 1M 10k C803 C806 C811F 33u R80810V 0.1u 47u C812 C8136.3V 0.1u 0.1u 47k REG_GND C815 C816 C817 0.1u 10u 10u 10V 6.3V LANC_SIG XLANC_PWR_ON R806 D801 470 MA8082-M(TX) EXTSTRB_ON R803 100k 0 D_3.2V Q802 3.2

G UN9113J-(K8).SO 0.4 XLANC_JACK_IN

R801 3.2 0 Q805 2SD2216J-R(TX).SO SIGNAL PATH 3.2 BUFFER

VIDEO SIGNAL

0 0 EXT_STRB_ON C810 XX CHROMA Y Y/CHROMA Q801 UN9213J-(K8).SO

REC H LANC_JACK_IN

05 PB

VIDEO

4-45 4-46 DD-141 (2/3), 76543218910 11 12 13 14 XLANC_PWR_ON USB_TXENL AV_JACK_IN USB_XVDATA USB_D+IN USB_D-IN USB_SUSPND USB_D+PULLUP

DSC-S30/S50 DD-141 (USB) SCHEMATIC DIAGRAM • See page 4-41 for DD-141 printed wiring board.

12345678910 11 12 13 14

DD-141 BOARD (3/3) A USB

-REF.NO.:1,000 SERIES- CN851 16P

XX MARK:NO MOUNT R857

24 16 REG_GND

NO MARK:STILL/PB MODE 15 D-

14 D+ Q851 R856 UN9113J-(K8).SO 24 SWITCH C856 13 REG_GND

B IC851 0.1u 12 USB_DET

3.1 11 N.C. USB_D+PULLUP USB I/F 3.1 10 N.C. 1.2 XLANC_PWR_ON JK-194 BOARD 9 N.C. CN201 (THROUGH THE R852 R853 8 N.C. FP-026 FLEXIBLE) XX IC851 1500 C855 PDIUSBP11APW,118 0.1u 7 N.C. (SEE PAGE 4-40)R851 XX 2.6 3.1 FB851 6 N.C. MODE VCC C854AV_JACK_IN 0.1u USB_TXENL 3.105AV_JACK_IN OE# VMO/FSEO USB_XVDATA 0 3.1 C857 4 V_OUTC RCV VPO XXUSB_D+IN 3.1 0.5 3 REG_GND VP USB_D+ USB_D-IN 3.1 0.5 C858 2 A_OUTVM USB_D- XX USB_SUSPND 3.1 3.1 1 REG_GND XLANC_PWR_ON SUSPND SPEED C853 V_OUT GND (NC) 22u C851 4 DD-141 BOARD (2/3) 6.3V 0.1u XLANC_JACK_IN EXTSTRB_ON

D

A_3.2V REG_GND CN852 80P R854 2200 C852 3.2 1 REG_GND REG_GND 210u 6.3V 3 REG_GND REG_GND 4 R85505AU_OUT REG_GND 6100k07AU_GND USB_D+OUT 8

E Q852 3.1

UN9216J-(K8).SO 9 XAU_LINE_MUTE USB_D-OUT 10 Q853 11 REG_GND REG_GND 12 UN9113J-(K8).SO C_OUT 3 DD-141 BOARD (2/3) 13 C_OUT USB_TXENL 14 C_OUT 15 REG_GND USB_XVDATA 16Y_OUT C_OUT 17 Y_OUT REG_GND 18 Q852,853 Y_OUT AU MUTE 19 REG_GND USB_D+IN 20 CNT_Y Y_OUT 21 CNT_Y USB_D-IN 22

F 23 REG_GND REG_GND 24

CNT_Y CNT_Y CNT_C 25 CNT_C USB_SUSPND 26 VOUT_ON 27 VOUT_ON USB_D+PULLUP 28 CNT_C CNT_C 29 REG_GND LANC_JACK_IN 30 LANC_JACK_IN VOUT_ON VOUT_ON 31 N.C. EXT_STRB_ON 32 EXT_STRB_ON 3 DD-141 BOARD (2/3) 33 N.C. USB_DET 34 A_4.9V D_3.2V 35 REG_GND AV_JACK_IN 36 37 A_3.2V A_4.9V 38 A_4.9V

G 39 A_3.2V A_4.9V 40 A_3.2V

D_1.8V 41 D_1.8VS D_1.8VP 42 43 D_1.8VS D_1.8VP 44 D_3.2V 45 D_3.2V CAM_3.2V 46 CAM_3.2V 47 D_3.2V CAM_3.2V 48 49 D_3.2V CAM_-7.5V 50 CAM_-7.5V ST_UNREG ST_UNREG ST_UNREG 51 ST_UNREG CAM_15V 52 CAM_15V 53 ST_UNREG PANEL_3.2V 54 PANEL_3.2V CAM_P_5V CAM_P_5V 2 DD-141 BOARD (1/3)

H 1 DD-141 BOARD (1/3) CAM_P_5V 55 CAM_P_5V PANEL_4.9V 56 PANEL_4.9V

57 CAM_P_5V PANEL_6.5V 58 PANEL_6.5V 59 SP_5V PANEL_13.2V 60 PANEL_13.2V 61 SP_5V PANEL_-15V 62 PANEL_-15.3V BL_UNREG BL_UNREG BL_UNREG 63 BL_UNREG BATT_UNREG 64 BATT_UNREG 65 BL_UNREG N.C. 66 67 N.C. LCD_DD_ON 68 LCD_DD_ON FAST_CHARGE FAST_CHARGE FAST_CHARGE 69 FAST_CHARGE SYS_DD_ON 70 SYS_DD_ON INIT_CHARGE INIT_CHARGE_ON

I INIT_CHARGE 71 INIT_CHARGE_ON REG_GND 72 REG_GND

73 LANC_DC LANC_SIG 74 LANC_SIG 3 DD-141 BOARD (2/3) 75 XLANC_PWR_ON REG_GND 76 05 77 REG_GND REG_GND 78

SIGNAL PATH 79 REG_GND REG_GND 80 VIDEO SIGNAL AUDIO SY-58 BOARD (7/8)

CN711 (SEE PAGE 4-27)

CHROMA Y Y/CHROMA SIGNAL J REC PB USB DD-141 (3/3) 4-47 4-48

, 4-3. WAVEFORMS

CD-262 BOARD PD-127 BOARD

1105.5 Vp-p 1.7 Vp-p 3.2 Vp-p 2H 56 usec H IC301 qh IC802 ra IC901 ej22qa 4.5 Vp-p 4.2 Vp-p 4.1 Vp-p 11.722 MHz 56 usec H IC301 qg IC802 wf IC901 wh33qs 7.4 Vp-p 4.5 Vp-p 4.8 Vp-p 125 µsecHHIC301 1, 2, 3 IC802 ws IC901244qd 7.4 Vp-p 4.5 Vp-p 4.8 Vp-p 125 µsecHHIC301 4, 5, 6 IC802 w; IC901355qf 1.4 Vp-p 4.8 Vp-p 4.8 Vp-p 125 µsecHHIC301 8 IC802 qf IC901 4

DD-141 BOARD 0.26 Vp-p H

0.5 Vp-p IC802 q; H 0.4 Vp-p IC802 qf

H

2 Vp-p IC8029H0.5 Vp-p IC802 9

H

0.5 Vp-p IC8028H4.8 Vp-p IC802 2 2H 1.0 Vp-p IC902 7 2.1µsec IC001 rf 4-49, 4-4. PARTS LOCATION DD-141 BOARD DD-141 BOARD (SIDE A) (SIDE B) C009 B-2 T001 A-3 C001 B-5 R026 A-5 C010 A-1 C002 B-5 R035 B-5 C013 A-2 C003 B-5 R036 B-4 C019 A-1 C004 A-5 R037 B-4 C020 A-2 C005 A-5 R038 A-4 C034 A-3 C007 B-5 R046 A-4 C035 A-4 C008 A-5 R047 B-4 C036 B-2 C014 B-5 R048 B-4 C037 A-3 C015 A-5 R049 A-4 C039 B-4 C016 A-4 R050 B-3 C043 A-3 C017 B-5 R051 B-4 C044 A-2 C018 A-5 R052 A-2 C054 A-2 C021 B-5 R053 A-2 C803 A-4 C022 A-5 R055 B-4 C809 B-5 C023 B-5 R056 A-4 C811 B-4 C024 B-4 R057 A-4 C817 A-5 C025 B-4 R058 A-2 C818 A-5 C026 A-5 R059 A-2 C819 B-5 C027 B-3 R060 A-4 C820 A-4 C028 A-3 R061 A-4 C852 B-5 C029 B-2 R062 B-4 C855 B-5 C030 A-3 R063 A-4 C031 A-3 R064 A-3 CN852 B-3 C032 B-3 R065 B-4 C033 A-3 R066 A-4 D001 A-3 C038 A-3 R067 A-3 D002 A-3 C042 A-2 R068 A-4 D801 A-5 C046 A-2 R069 B-4 C047 A-2 R070 A-3 L001 B-3 C048 A-3 R071 B-4 L002 A-3 C049 B-3 R072 B-4 L003 B-4 C050 A-4 R073 B-4 L004 B-3 C051 B-3 R074 A-4 L006 A-4 C052 A-4 R075 A-4 L008 B-4 C053 A-4 R076 A-4 L010 A-4 C055 A-4 R078 A-4 L011 B-2 C806 A-2 R081 B-4 L013 A-2 C808 A-2 R804 A-1 L014 B-4 C812 A-2 R805 A-4 L801 B-4 C813 A-1 R807 A-1 L802 A-5 C814 A-2 R856 B-1 C815 A-1 R857 B-1 Q005 A-1 C816 A-1 Q006 A-2 C851 B-2 Q007 A-2 C853 B-2 Q008 A-1 C854 A-1 Q016 B-4 C856 B-1 Q801 B-5 Q802 B-5 CN001 B-4 Q805 B-5 CN851 A-1 Q806 A-5 Q807 A-4 D003 B-3 Q851 A-5 D004 B-3 Q852 B-5 Q853 B-5 FB851 B-2 R006 A-1 IC001 B-5 R007 A-1 IC802 A-1 R009 A-1 IC851 B-2 R010 A-1 R011 A-1 L005 A-3 R014 A-1 L009 A-3 R015 B-1 L012 A-2 R016 B-1 R017 A-1 Q001 B-3 R018 B-5 Q002 B-2 R019 A-1 Q003 B-3 R020 A-1 Q004 B-2 R021 A-1 Q009 A-3 R022 A-1 Q013 A-4 R023 A-1 Q014 A-2 R027 A-1 Q017 A-2 R028 B-1 Q018 A-2 R029 B-1 Q019 A-4 R030 B-1 Q020 B-4 R031 B-1 Q021 A-4 R032 A-1 Q022 A-3 R033 A-1 Q023 B-4 R034 A-1 Q024 A-4 R039 A-1 Q025 A-3 R040 A-1 Q026 B-4 R042 A-2 Q027 A-4 R043 A-1 Q028 A-3 R044 A-2 Q029 B-4 R045 A-2 Q030 A-4 R054 A-2 Q031 A-4 R801 B-5 Q032 A-3 R803 B-5 Q033 A-4 R806 B-5 R808 A-5 R001 B-5 R809 A-5 R002 A-4 R810 B-5 R004 A-5 R811 A-5 R005 B-5 R812 A-4 R008 B-5 R853 A-5 R012 B-5 R854 B-5 R013 A-5 R855 B-5 R024 B-5 R025 B-5 4-52 E,

DSC-S30/S50 SECTION 5 ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board

The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board. Procedure 1 Save the EVR data of the machine in which a board is going to be replaced. Download the saved data after a board is replaced. (Machine before starting repair) PC PC (Machine after a board is replaced) Save the EVR data Download the saved to a personal computer. data to a machine. Procedure 2 Remove the EEPROM from the board of the machine that is going to be repaired. Install the removed EEPROM to the replaced board. Remove the EEPROM and install it. (Former board) (New board) Procedure 3 When the data cannot be saved due to defective EEPROM, or when the EEPROM cannot be removed or in- stalled, save the data from the same model of the same destination, and download it. (Machine to be repaired) PC (Machine to be repaired) Download the data. Save the data. (The same model of the same destination) After the EVR data is saved and downloaded, check the respective items of the EVR data. (Refer to page 5-2 for the items to be checked.) 5-1, 1-1. Adjusting items when replacing main parts and boards When replacing main parts and boards, adjust the items indicated by z in the following table. Replaced parts Block Mounted parts Board replacement replacement replacement Adjustment section Adjustment Initialization of Initialization of D page datazz7, B, D, E, F, page data Initialization of 7, B, E, F page datazzVideo Video sync level adj. zzzzzVideo burst level adj. zzzzzCamera Hall adj. zzzzFlange back adj. zzzzzFNo. standard data inputzzzzzMechanical shutter adj. zzzzzLight level adj. zzzzzzMixed color cancel adj. zzzzzzAuto white balance standard data inputzzzzzAuto white balance adj. zzzzzColor reproduction adj. zzzzzStrobe white balance adj. zzzzzzzCCD (black and white) defect compensationzzzzLCD LCD initial data inputzzVCO adj. zzzzzDrange adj. zzzzzBright adj. zzzzzContrast adj. zzzzzColor adj. zzzzzV-COM level adj. zzzzzV-COM adj. zzzzzzWhite balance adj. zzzzzzzSystem control Battery down adj. z z Table 5-1-1 5-2 Lens device Strobe unit LCD block LCD901 (LCD panel) LCD block ND901 Back light unit CD-262 board IC301 (CCD imager) SY-58 board IC102 (S/H, AGC, A/D) SY-58 board IC186 (EVR) DD-141 board IC802 (VIDEO AMP) PD-127 board IC802 (RGB decoder) PD-127 board IC901 (Timing generator) PD-127 board IC801 (EVR) PD-127 board (COMPLETE) CD-262 board (COMPLETE) DD-141 board (COMPLETE) SY-58 board (COMPLETE) SY-58 board IC406 EEPROM SY-58 board IC507 EEPROM, 5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Auto white balance adjustment/check J-1 Filter for color temperature correction (C14) J-6080-058-A White balance adjustment/check J-2 Pattern box PTB-450 J-6082-200-A J-3 Color chart for pattern box J-6020-250-A Adjustment remote commander (RM-95 upgraded). J-4 J-6082-053-B (Note 1) J-5 Siemens star chart J-6080-875-A For checking the flange back J-6 Clear chart for pattern box J-6080-621-A For connecting the adjustment remote commander J-7 CPC-9 jig (Note 2) J-6082-393-C For adjusting the LCD block J-8 Mini pattern box J-6082-353-B For adjusting the flange back Extension cable (16P, 0.5mm, L=100mm) J-6082-357-A For extension between the DD-141 board (CN851) and J-9 Extension cable (16P, 0.5mm, L=200mm) J-6082-398-A the JK-194 board (CN201) For extension between the CD-262 board (CN301) and J-10 Extension cable (18P, 0.5mm) J-6082-423-A the SY-58 board (CN101) J-11 Back ground paper J-2501-130-A For adjusting the strobe Note 1: If the micro processor IC in the adjustment remote Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be commander is not the new micro processor (UPD7503G- used, because it cannot operate the adjustment remote C56-12), The pages cannot be switched. In this case, commander. replace with the new micro processor (8-759-148-35). J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 J-10 J-11 Fig. 5-1-1 5-3, 1-1-2. Preparations Note 1: For details of how remove the cabinet and boards, refer Pattern box to “2. DISASSEMBLY”. Note 2: When performing only the adjustments, the lens block and boards need not be disassemble. 1) Connect the equipment for adjustments according to Fig. 5-1- 5. 2) Connect the Adjusting remote commander to SY-58 board CN709 via CPC-9 jig (J-6082-393-C). (See Fig. 5-1-3) L Note 3: Setting the “Forced STILL mode power ON” Mode 1) Select page: 0, address: 01, and set data: 01. 2) Select page: D, address: 10, set data: 01, and press the PAUSE button of the adjusting remote com- Front side of the lens mander. The Above procedure will enable the camera power to the turned on. After completing adjustments, be L = About 90 cm sure to exit the “Forced STILL mode power ON Mode”. Note 4: Exiting the “Forced STILL mode power ON Mode” Fig. 5-1-2 1) Select page: 0, address: 01, and set data: 01. Open the battery lid assembly 2) Select page: D, address: 10, set data: 00, and press the PAUSE button of the adjusting remote com- mander. 3) Select page: 0, address: 01, and set data: 00. 1-1-3. Discharging of the flashlight power supply The capacitor which is used as power supply of flashlight is charged with 200 V to 300 V voltage. Discharge this voltage before start- ing adjustments in order to protect service engineers from electric shock during adjustment. Discharge procedure SY-58 board 1. Press the FLASH button (SW-339 board S103) and turn off (CN709) the FLASH LED (SW-339 board D102). 2. Fabricate the discharging jig as shown in Fig. 5-1-4 locally by yourself. Connect the discharging jig to the positive (+) and CPC lid negative (–) terminal of the flash voltage charge capacitor. Al- 1(Note 3) low ten seconds to discharge the voltage. 18 1 kΩ/1W1CPC-9 jig (J-6082-393-C) BT holder (18P flexible board) Wrap insulating tape. assembly (Note 1, 2) Fig. 5-1-4 CPC lid Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 3: In removing the CPC lid, start from the upper side. Fig. 5-1-3 5-4, Vector Color monitor scope Video Terminated (Yellow) at 75 Ω JK-194 Audio board (White) S50 S30 (S50) A/V VIDEO Adjustment remote OUT OUT commander J201 AC IN Extension Cable Memory Stick (J-6082-398-A): L=200mm (J-6082-357-A): L=100mm MS-50 board CN851 Extension Cable AC power (J-6082-423-A) adaptor CPC-9 jig (J-6082-393-C) DC-IN Connector CN003 CN001 CN005 12 CN001 Lens block 12 pin 1 SY-58 DD-141 assembly CN711 board CN704 board 18 pin11– + CN706 CN713 CN707 CN701 CN702 CN708 CN101 CN703 SW-339 board DC power supply (6.0 to 7.2 V DC) (Note 2) Flash unit Control switch block (Mode SW) Control switch block Note 1: In changing data, wait for more than 5 seconds after the (Zoom/power SW) set was turned on, then change the data. Note 2: Must be connected when performing the battery down adjustment. Note 3: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Fig. 5-1-5 5-5 CN709 to PD-127 board CN802 to PD-127 board CN101 CN183 CN801 to KJ-11 board CN201, 1-1-4. Precautions 1. Setting the Switch Unless otherwise specified, set the switches as follows and per- form adjustments. 1. FOCUS button (SW-339 board S107) ... MANUAL 5. DEMO (Menu display) ... OFF 2. PROGRAM AE button (SW-339 board S104) 6. VIDEO OUT (Menu display) ... NTSC ... AUTO (No mark indicated on LCD) 7. WHITE BALANCE (Menu display) ... AUTO 3. DISPLAY button (SW-339 board S102) ... OSD OFF 8. EXPOSURE ... 0EV 4. P. EFECT (Menu display) ... OFF 9. FLASH LEVEL ... NORMAL 2. Order of Adjustments Basically carry out adjustments in the order given. Color bar chart (Color reproduction adjustment frame) Electronic beam scanning frame

H

C C=D D CRT picture frame

V

A B A=BBAFig. b (monitor TV picture) Enlargement Difference in level Adjust the camera zoom and direction to obtain the output waveform shown in Fig a and the monitor TV display shown in Fig. b. B A Fig. 5-1-6 3. Subjects 1) Color bar chart (Standard picture frame). When performing adjustments using the color bar chart, ad- just the picture frame as shown in Fig. 5-1-6. (Standard pic- ture frame) 2) Clear chart (Standard picture frame) Remove the color bar chart from the pattern box and insert a clear chart in its place. (Do not perform zoom operations dur- ing this time) 5-6 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 4. Preparing the Flash Adjustment Box A dark room is required to provide an accurate flash adjustment. If it is not available, prepare the flash adjustment box as given below; 1) Provide woody board A, B and C of 15 mm thickness. woody board A (2) woody board B (2) woody board C (1) 530 mm 500 mm 1000 mm 1026 mm 1026 mm 1000 mm 1030 mm 1000 mm Fig. 5-1-8 2) Apply black mat paint to one side of woody board A and B. 3) Attach background paper (J-2501-130-A) to woody board C. 4) Assemble so that the black sides and the background paper side of woody board A, B and C are internal. (Fig 5-1-9) woody board A woody board B woody board A woody board B woody board C Fig. 5-1-9 5-7, 1-2. INITIALIZATION OF B, D, E, F, 7 PAGE DATA 3. D Page table 1-2-1. INITIALIZATION OF D PAGE DATA Note 1: Fixed data-1: Initialized data. 1. Initializing the D Page Data (Refer to “1. Initializing the D Page Data”) Note: If the D page data has been initialized, the following Note 2: Fixed data-2: Modified data. adjustments need to be performed again. (Refer to “2. Modified of D Page Data”) 1) Modification of D page data 2) LCD system adjustments Address Initial value Remark 3) Battery end adjustments S30 S50 00 to 0F Adjusting page D 10 to 1B Fixed data-1 (Initialized data) Adjusting Address 10 to EF 1C Fixed data-2 1D Initializing Method: 1E to 5F Fixed data-1 (Initialized data) 1) Select page: 0, address: 01, and set data: 01. 60 Fixed data-2 2) Select page: 2, address: 03, and set data: 03 (S30) or data: 02 61 (S50). 3) Select page: 2, address: 00, and set data: 2D. 4) Select page: 2, address: 01, set data: 2D, and press the PAUSE 63 button of the adjustment remote commander. 64 to 6F Fixed data-1 (Initialized data) 5) Select page: 2, address: 02, and check that the data changes to 70 Fixed data-2 “01”. 71 6) Perform “Modification of D Page Data”. 72 to 84 Fixed data-1 (Initialized data) 85 Fixed data-2 2. Modification of D Page Data 86 to 8F Fixed data-1 (Initialized data) If the D page data has been initialized, change the data of the “Fixed data-2” address shown in the following table by manual input. 90 80 80 Battery down adj. 91 88 88 Modifying Method: 92 AD AD 1) Before changing the data, select page: 0, address: 01, and set 93 C2 C2 data: 01. 94 CD CD 2) New data for changing are not shown in the tables because 95 to 97 Fixed data-1 (Initialized data) they are different in destination. When changing the data, copy the data built in the same model. 98 Fixed data-2 Note : If copy the data built in the different model, the 99 camcorder may not operate. 9A 3) When changing the data, press the PAUSE button of the ad- 9B justment remote commander each time when setting new data 9C to write the data in the non-volatile memory. 9D 4) Check that the data of adjustment addresses is the initial value. 9E If not, change the data to the initial value. 9C Processing after Completing Modification of D Page data A0 1) Select page: 2, address: 00, and set data: 29. A1 2) Select page: 2, address: 01, and set data: 29, and press the A2 to A4 Fixed data-1 (Initialized data) PAUSE button of the adjustment remote commander. A5 Fixed data-2 A6 A7,A8 Fixed data-1 (Initialized data) A9 Fixed data-2 AA to CF Fixed data-1 (Initialized data) D0 BC BC Bright adj. (LCD) D1 80 80 Color adj. (LCD) D2 B9 B9 White balance adj. (LCD) D3 B7 B7 D4 BE BE Contrast adj. (LCD) D5 C8 C8 D Range adj. (LCD) D6 7C 7C V-COM Level adj. (LCD) D7 80 80 VCO adj. (NTSC) (LCD) D8 74 74 V-COM adj. (LCD) D9 to DC Fixed data-1 (Initialized data) DD 88 88 VCO adj. (PAL) (LCD) DE Fixed data-2

DF

E0 to EF Fixed data-1 (Initialized data) 5-8, 1-2-2. Initializing the B, E, F, 7 Page Data 3. B Page table 1. Initializing the B, E, F, 7 Page Data Note 1: Fixed data-1: Initialized data. Note: If the B, E, F Page data has been initialized, “Modification (Refer to “1. Initializing the B, E, F, 7 Page Data”) of B, E, F, 7 Page Data” and following adjustments need Note 2: Fixed data-2: Modified data. to be performed again. (Refer to “2. Modified of B, E, F, 7 Page Data”) 1) Modification of B, E, F, 7 page data 2) Video system adjustments Address Initial value Remark 3) Camera system adjustments S30 S50 00 Fixed data-2 Adjusting page F 01 to FF Fixed data-1 (Initialized data) Adjusting Address 10 to FF Adjusting page E Adjusting Address 00 to FF 4. E Page table Adjusting page B Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”) Adjusting Address 00 to FF Note 2: Fixed data-2: Modified data. Adjusting page 7 (Refer to “2. Modified of B, E, F, 7 Page Data”) Adjusting Address 00 to FF Address Initial value Remark S30 S50 Initializing Method: 00 to F5 Fixed data-1 (Initialized data) 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 6, address: 00, and set data: 2D. F6 Fixed data-2 3) Select page: 6, address: 01, set data: 2D, and press the PAUSE F7 to FF Fixed data-1 (Initialized data) button of the adjustment remote commander. 4) Select page: 6, address: 02, and check that the data changes to “01”. 5) Perform “Modification of B, E, F, 7 Page Data”. 2. Modification of B, E, F, 7 Page Data If the B, E, F, 7 Page data has been initialized, change the data of the “Fixed data-2” address shown in the following tables by manual input. Modifying Method: 1) Before changing the data, select page: 0, address: 01, and set data: 01. 2) New data for changing are not shown in the tables because they are different in destination. When changing the data, copy the data built in the same model. Note: If copy the data built in the different model, the camcorder may not operate. 3) When changing the data, press the PAUSE button of the ad- justment remote commander each time when setting new data to write the data in the non-volatile memory. 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. Processing after Completing Modification of B, E, F, 7 Page data 1) Select page: 2, address: 00, and set data: 29. 2) Select page: 2, address: 01, and set data: 29, and press the PAUSE button of the adjustment remote commander. 5-9, 5. F Page table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modified of B, E, F, 7 Page Data”) Address Initial value Remark Address Initial value Remark S30 S50 S30 S50 00 to 0F 5B Fixed data-1 (Initialized data) 10 to13 Fixed data-1 (Initialized data) 5C 63 63 Color reproduction adj. 14 12 12 Flange back adj. 5D 83 83 15 A8 A8 5E 03 03 16 18 18 5F E9 E9 17 C5 C5 60 to 63 Fixed data-1 (Initialized data) 18 12 12 64 10 10 Strobe white balance adj. 19 C9 C9 65 61 61 Video sync level adj. 1A 00 00 66 61 61 Video burst level adj. 1B 00 00 67, 68 Fixed data-1 (Initialized data) 1C 00 00 69 00 01 Strobe white balance adj. 1D 00 00 6A AD 38 1E 41 41 6B 00 00 1F 00 00 6C 0B 0B Mechanical shutter adj. 20 20 20 6D C2 C2 21 20 20 6E 09 09 22 20 20 6F 42 42 23 44 44 70 06 06 24 0A 0A 71 C2 C2 25 00 00 72 05 05 26 6B 7D Light level adj. 73 C2 C2 27 Fixed data-1 (Initialized data) 74 04 04 28 7B 8D Light level adj. 75 C2 C2 29 4F 52 F No. standard data input 76 33 33 2A 49 4B 77 33 33 2B 42 45 78 33 33 2C 40 42 79 33 33 2D Fixed data-1 (Initialized data) 7A 33 33 2E 7C 7E Hall adj 7B 33 33 2F 9A 9B 7C 33 33 30 to 33 Fixed data-1 (Initialized data) 7D 33 33 34 15 15 Hall adj 7E 33 33 35 7D 7D 7F 33 33 36 to 39 Fixed data-1 (Initialized data) 80 00 00 Auto white balance adj. 3A 2F 2F Auto white balance standard data input 81 to 9F Fixed data-1 (Initialized data) 3B 37 37 A0 00 00 Mixed color cancel adj. 3C 40 40 A1 00 00 3D D0 D0 A2 00 00 3E Fixed data-1 (Initialized data) A3 00 00 3F B5 B5 Auto white balance adj. A4 to FF Fixed data-1 (Initialized data) 40 43 43 41 03 03 Color reproduction adj. 42 E9 E9 43 63 63 44 83 83 45 D5 D5 46 FE FE 47 73 73 48 45 45 49 to 4C Fixed data-1 (Initialized data) 4D 27 27 Strobe white balance adj. 4E 77 77 4F to 58 Fixed data-1 (Initialized data) 59 00 00 Auto white balance standard data input 5A 14 14 Mechanical shutter adj. 5-10, 6. 7 Page table Note 1: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, E, F, 7 Page Data”) Note 2: Fixed data-2: Modified data. (Refer to “2. Modified of B, E, F, 7 Page Data”) Address Initial value Remark Address Initial value Remark S30 S50 S30 S50 00 to 5F Fixed data-1 (Initialized data) 93 FF FF CCD white defect compensation 60 0F 0F CCD black defect compensation 94 0F 0F 61 FF FF 95 FF FF 62 0F 0F 96 0F 0F 63 FF FF 97 FF FF 64 0F 0F 98 0F 0F 65 FF FF 99 FF FF 66 0F 0F 9A 0F 0F 67 FF FF 9B FF FF 68 0F 0F 9C 0F 0F 69 FF FF 9D FF FF 6A 0F 0F 9E 0F 0F 6B FF FF 9F FF FF 6C 0F 0F A0 0F 0F 6D FF FF A1 FF FF 6E 0F 0F A2 0F 0F 6F FF FF A3 FF FF 70 0F 0F A4 to FF Fixed data-1 (Initialized data) 71 FF FF 72 0F 0F 73 FF FF 74 0F 0F 75 FF FF 76 0F 0F 77 FF FF 78 0F 0F 79 FF FF 7A 0F 0F 7B FF FF 7C 0F 0F 7D FF FF 7E 0F 0F 7F FF FF 80 0F 0F 81 FF FF 82 0F 0F 83 FF FF 84 0F 0F 85 FF FF 86 0F 0F 87 FF FF 88 0F 0F CCD white defect compensation 89 FF FF 8A 0F 0F 8B FF FF 8C 0F 0F 8D FF FF 8E 0F 0F 8F FF FF 90 0F 0F 91 FF FF 92 0F 0F 5-11, 1-3. VIDEO SYSTEM ADJUSTMENTS 2. Video Burst Level Adjustment 1. Video Sync Level Adjustment Adjust the burst level of the composite video signal output Adjust the sync level of the composite video signal output Mode PLAY Mode PLAY Signal Color bar (Test signal) Signal Color bar (Test signal) Measurement Point Video terminal of A/V OUT jack Measurement Point Video terminal of A/V OUT jack (75 Ω terminated) (75 Ω terminated) Measuring Instrument Oscilloscope Measuring Instrument Oscilloscope Adjustment Page F Adjustment Page F Adjustment Address 66 Adjustment Address 65 Specified Value A=286 ± 5 mV (NTSC) Specified Value A=286 ± 5 mV (NTSC) A=300 ± 5 mV (PAL) A=300 ± 5 mV (PAL) Menu setting: Menu setting: 1) VIDEO OUT of SET UP menu 1) VIDEO OUT of SET UP menu ... NTSC (NTSC mode) ... NTSC (NTSC mode) ... PAL (PAL mode) ... PAL (PAL mode) Adjusting method: Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: 04. 2) Select page: 5, address: F1, and set data: 04. 3) Select page: F, address: 66, change the data and set the burst 3) Select page: F, address: 65, change the data and set the sync level (A) to the specified value. level (A) to the specified value. 4) Press the PAUSE button of the adjusting remote commander. 4) Press the PAUSE button of the adjusting remote commander. Processing after Completing Adjustments: Processing after Completing Adjustments: 1) Select page: 5, address: F1, and set data: 00. 1) Select page: 5, address: F1, and set data: 00. 2) Select page: 0, address: 01, and set data: 00. 2) Select page: 0, address: 01, and set data: 00.

A A

H H Fig. 5-1-10 Fig. 5-1-11 5-12, 1-4. CAMERA SYSTEM ADJUSTMENT 1. HALL Adjustment For detecting the position of lens iris, adjust the HALL AMP Before perform the camera system adjustments, check that the gain and offset. specified values of “VIDEO SYSTEM ADJUSTMENTS” are satisfied. Mode STILL Subject Not required Data setting during camera system adjustment Perform the following data setting before the camera system ad- Measurement Point Displayed data of page: 1 (Note 2) justments. Measuring Instrument Adjusting remote commander 1) Select page: 0, address: 01, and set data: 01. Adjustment Page F 2) After writing down the original data of the following addresses, input the following data. Adjustment Address 2E, 2F, 34, 35 Specified Value 13 to 17 during IRIS OPEN Page Address Data 7B to 7F during IRIS CLOSE E 43 10 E 8F 00 Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. B 67 00 Note 2: The right four digits of the page: 1 displayed data of the Note: Press the pause button of the adjusting remote adjusting remote commander. commander each time to set data. 1:XX:XX After completing the camera system adjustments, release the Displayed data data setting: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select the above address, and input the orignal data writen 1) Select page: 0, address: 01, and set data: 01. down at step 2). 2) Select page: 5, address: F1, and set data: FF. Note: Press the pause button of the adjusting remote 3) Select page: D, address: 63, set data: 40, and press the PAUSE commander each time to set data. button of the adjusting remote commander. 3) Select page: 0, address: 01, and set data: 00. 4) Perform “Data setting dring camera system adjuatment”. 5) Select page: 6, address: 94, and set data: 15. 6) Select page: 6, address: 95, and set data: 7D. 7) Select page: 6, address: 01, set data: 6D, and press the PAUSE button. (The HALL adjustment is performed and the adjustment data is stored in page: F, address: 2E, 2F, 34 and 35) 8) Select page: 6, address: 02, and check that the data is “01”. 9) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Checking method: 1) Select page: 0, address: 03, and set data: 03. 2) Select page: 6, address: 01, set data: 01, and press the PAUSE button of the adjusting remote commander. 3) Select page: 1, and check that the displayed data (Note 2) during IRIS OPEN satisfies the specified value. 4) Select page: 6, address: 01, set data: 03, and press the PAUSE button. 5) Select page: 1, and check that the displayed data (Note 2) during IRIS CLOSE satisfies the specified value. Processing after Completing Adjustments: 1) Select page: 0, address: 03, and set data: 00. 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button of the adjusting remote commander. 3) Select page: 6, address: 95, and set data: 00. 4) Select page: 6, address: 94, and set data: 00. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: D, address: 63, set data: 00, and press the PAUSE button. 7) Release the data setting performed at step 4). 8) Select page: 0, address: 01, and set data: 00. 5-13, 2. Flange Back Adjustment Adjusting method: (Using the minipattern box) 1) Install the minipattern box so that the distance between it The inner focus lens flange back adjustment is carried out auto- and the front of lens of the camera is less than 3cm. matically. In whichever case, the focus will be deviated during 2) Make the height of minipattern box and the camera equal. auto focusing/manual forcusing. 3) Check the output voltage of the regulated power supply is the specified voltage ± 0.01 Vdc. Mode STILL 4) Check that the center of Siemens star chart meets the center Subject Siemens star chart with ND filter of shot image screen with the zoom lens at TELE end and WIDE end respectively. for minipattern box (Note 1) 5) Select page: 0, address: 01, and set data: 01. Measurement Point Check operation on TV monitor 6) Select page: 5, address: F1, and set data: FF. Measuring Instrument 7) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. Adjustment Page F 8) Perform “ Data setting during camera system adjustment”. Adjustment Address 14 to 25 (Refer to page 5-13) 9) Check that the data on page: F, addresses: 14 to 25 are initial Note 1: Dark Siemens star chart. values (See table below). Note 2: Check that the data of page: 6, address: 02 is “00”. Address Data Address Data If not, turn the power of unit OFF/ON. 14 12 1D 00 Preparations before adjustments: 15 A8 1E 41 The minipattern box is installed as shown in the following figure. 16 18 1F 00 Note 3: The attachment lenses are not used. 17 C5 20 20 Note 4: Take care not to hit the mini-pattern box when extending 18 12 21 20 the lens. 19 C9 22 20 1A 00 23 44 Specified voltage: The specified voltage varies according to the minipatternbox, so adjustment the power sup 1B 00 24 0A ply output voltage to the specified voltage 1C 00 25 00 written on the sheet which is supplied with the 10) Select page: 6, address: 01, set data: 13, and press the PAUSE minipattern box. button. Below 3 cm 11) Select page: 6, address: 01, set data: 27, and press the PAUSE button. (The flange back adjustment is performed and the Minipattern box adjustment data is stored in page: F, address: 14 to 25) 12) Select page: 6, address: 02, and check that the data is “01”. Camera Processing after completion of adjustment: Camera 1) Select page: 6, address: 01, set data: 00, and press the PAUSE table button of the adjusting remote commander. Regulated power supply 2) Select page: 5, address: F1, and set data: 00. Output voltage : Specified voltage ±0.01Vdc 3) Select page: D, address: 63, set data: 00, and press the PAUSE Output current : more than 3.5A button. 4) Release the data setting performed at step 8). (Refer to page 5-13) Red (+) 5) Select page: 0, address: 01, and set data: 00. 6) Perform “Flange Back Check”. Black (–) Yellow (SENS +) White (SENS –) Need not connected Black (GND) Fig. 5-1-12 5-14, 3. Flange Back Check Mode STILL Subject Siemens star (2.0 m from the front of the lens) (Luminance: approx. 200 lux) Measurement Point Check operation on TV monitor Measuring Instrument Specified value Focused at the TELE end and WIDE end Checking method: 1) Place the Siemens star 2.0 m from the front of the lens. 2) To open the IRIS, decrease the luminous intensity to the Si- emens star up to a point before noise appear on the image. 3) Select page: 0, address: 01, and set data: 01. 4) Select page: 5, address: F1, and set data: FF. 5) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. 6) Perform “ Data setting during camera system adjustment”. (Refer to page 5-13) 7) Shoot the Siemens star with the zoom TELE end. 8) Turn on the auto focus. 9) Check that the lens is focused. 10) Select page: 6, address: 2C, and set data: 01. 11) While observe the TV monitor, change the zoom to the WIDE end and check that the lens is focused. Processing after completion of adjustment: 1) Select page: 6, address: 2C, and set data: 00. 2) Select page: 5, address: F1, and set data: 00. 3) Select page: D, address: 63, set data: 00, and press the PAUSE button of the adjusting remote commander. 4) Release the data setting performed at step 6). (Refer to page 5-13) 5) Select page: 0, address: 01, and set data: 00. 5-15, 4. F No. Standard Data Input 5. Mechanical Shutter Adjustment Compensate the unevenness of the iris meter sensitivity. Adjust the period which the mechanical shutter is closed, and compensate the exposure. Mode STILL Subject Clear chart Mode STILL 10 cm from the front of the lens) Subject Clear chart Adjustment Page F (10 cm from the front of the lens) Adjustment Address 29 to 2C Adjustment Page F Adjustment Address 5A, 6C to 7F Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Adjusting method: 1) Shoot the Clear chart with the zoom WIDE end. Adjusting method: 2) Select page: 0, address: 01, and set data: 01. 1) Shoot the Clear chart with the zoom WIDE end. 3) Select page: 5, address: F1, and set data: FF. 2) Select page: 0, address: 01, and set data: 01. 4) Select page: D, address: 63, set data: 40, and press the PAUSE 3) Select page: 5, address: F1, and set data: FF. button of the adjusting remote commander. 4) Select page: D, address: 63, set data: 40, and press the PAUSE 5) Perform “ Data setting during camera system adjustment”. button of the adjusting remote commander. (Refer to page 5-13) 5) Perform “ Data setting during camera system adjustment”. 6) Select page: 6, address: 01, set data: BB, and press the PAUSE (Refer to page 5-13) button. 6) Select page: 6, address: 01, set data: AD, and press the PAUSE 7) (The F No. standard data input is performed and the stan- button. (The mechanical shutter adjustment is performed and dard data is stored in page: F, address: 29 to 2C) the adjustment data is stored in page: F, address: 5A and 6C 8) Select page: 6, address: 02, and check that the data is “01”. to 7F) 7) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: 8) Select page: 6, address: AB, and check that the data is “00”. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE (If the data other than “00”, mechanical shutter adjustment button of the adjusting remote commander. has errors) 2) Select page: 5, address: F1, and set data: 00. 3) Select page: D, address: 63, set data: 00, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 4) Release the data setting performed at step 5). button of the adjusting remote commander. (Refer to page 5-13) 2) Select page: 5, address: F1, and set data: 00. 5) Select page: 0, address: 01, and set data: 00. 3) Select page: D, address: 63, set data: 00, and press the PAUSE button. 4) Release the data setting performed at step 5). (Refer to page 5-13) 5) Select page: 0, address: 01, and set data: 00. 5-16, 6. Picture Frame Setting Check on the oscilloscope Mode STILL 1. Horizontal period Subject Color bar chart A=B C=D (Color reproduction adjustment frame) B C Measurement Point Video terminal of A/V OUT jackAD(75 Ω terminated) Measuring Instrument Oscilloscope and TV monitor Specified Value A=B, C=D, E=F Note 1: Displayed data of page 1 of adjusting remote commander. 1:XX:XX XL or YL data XH or YH data Setting method: 1) Select page: 5, address: F1, and set data: FF. 2) Perform “ Data setting during camera system adjustment”. (Refer to page 5-13) 3) Adjust the zoom and the camera direction, and set to the pic- Fig. 5-1-13 ture frame to the specified position. 4) Mark the position of the picture frame on the TV monitor, 2. Vertical period and adjust the picture frame to this position in following ad- justments using “Color reproduction adjustment frame”. E E=F F 5) Select page: 0, address: 03, and set data: 18. 6) Select page: 1, and note down the XH and XL data. (Note 1) 7) Select page: 0, address: 03, and set data: 22. 8) Select page: 1, and note down the YH and YL data. (Note 1) 9) Release the data setting performed at step 2). V (Refer to page 5-13) Fig. 5-1-14 10) Select page: 5, address: F1, and set data: 00. Check on the TV monitor How to reset the zoom and focus when they deviated: If the zoom and focus deviated due to some reason, reset them in the following method. 1) Select page: 6, address: 90, and set data: XL. (Note 2) 2) Select page: 6, address: 91, and set data: XH. (Note 2) 3) Select page: 6, address: 92, and set data: YL. (Note 3) 4) Select page: 6, address: 93, and set data: YH. (Note 3) 5) Select page: 6, address: 01, set data: 79, press the PAUSE button, and wait for 1 second. Color bar chart picture frame TV monitor picture frame 6) Select page: 6, address: 2C, and set data: 01. Fig. 5-1-15 7) Select page: 6, address: 01, set data: 00, and press the PAUSE button. Note 2: The data noted down at step 6) of “Setting method”. Note 3: The data noted down at step 8) of “Setting method”. 5-17, 7. Light Level Adjustment 8. Mixed Color Cancel Adjustment Adjust the standard LV value. To perform mixed color cancel adjustment based on data of each color in color bar. Mode STILL Subject Clear chart Mode STILL (Color reproduction adjustment frame) Subject Color bar chart Measurement Point Displayed data of page: 1 (Note 2) (Color reproduction adjustment frame) Measuring Instrument Adjusting remote commander Adjustment Page F Adjustment Page F Adjustment Address A0 to A3 Adjustment Address 26, 28 Note 1: Perform “Light Level Adjustment” before this Specified Value AE level: 0FE0 to 1020 adjustment. Note 2: Check that the data of page: 6, address: 02 is “00”. Note 1: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. If not, turn the power of unit OFF/ON. Note 2: The right four digits of the page: 1 displayed data of the Adjusting method: adjusting remote commander. 1) Select page: 0, address: 01, and set data: 01. 1:XX:XX 2) Select page: 5, address: F1, and set data: FF. Displayed data 3) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. Adjusting method: 4) Perform “ Data setting during camera system adjustment”. 1) Select page: 0, address: 01, and set data: 01. (Refer to page 5-13) 2) Select page: 5, address: F1, and set data: FF. 5) Select page: 6, address: 01, set data: D7, and press the PAUSE 3) Select page: D, address: 63, set data: 40, and press the PAUSE button. button of the adjusting remote commander. 6) Select page: 6, address: 01, set data: D5, and press the PAUSE 4) Perform “ Data setting during camera system adjustment”. button. (The mixed color adjustment is performed and the (Refer to page 5-13) adjustment data is stored in page: F, address: A0 to A3) 5) Select page: 6, address: 01, set data: 0D, and press the PAUSE 7) Select page: 6, address: 02, and check that the data is “01”. button. (The light level adjustment is performed and the ad- justment data is stored in page: F, address: 26 and 28) Processing after Completing Adjustments: 6) Select page: 6, address: 02, and check that the data is “01”. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 7) Select page: 0, address: 03, and set data: 06. button of the adjusting remote commander. 8) Select page: 1, and check that the displayed data (Note 2) 2) Select page: 5, address: F1, and set data: 00. satisfies the AE level specified value. 3) Select page: D, address: 63, set data: 00, and press the PAUSE button. Processing after Completing Adjustments: 4) Release the data setting performed at step 4). 1) Select page: 0, address: 03, and set data: 00. (Refer to page 5-13) 2) Select page: 6, address: 01, set data: 00, and press the PAUSE 5) Select page: 0, address: 01, and set data: 00. button of the adjusting remote commander. 3) Select page: 5, address: F1, and set data: 00. 4) Select page: D, address: 63, set data: 00, and press the PAUSE button. 5) Release the data setting performed at step 4). (Refer to page 5-13) 6) Select page: 0, address: 01, and set data: 00. 5-18, 9. Auto White Balance Standard Data Input Note 1: Perform “Auto White Balance Standard Data Input” Adjust the white balance standard data at 3200K. before this adjustment. Note 2: Check that the data of page: 6, address: 02 is “00”. Mode STILL If not, turn the power of unit OFF/ON. Subject Clear chart Note 3: The right four digits of the page: 1 displayed data of the adjusting remote commander. (Color reproduction adjustment frame) 1:XX:XX Adjustment Page F Displayed data Adjustment Address 3A to 3D, 59 Adjusting method: 1) Place the C14 filter for color temperature correction on the Note 1: Perform “Light Level Adjustment” and “Mixed Color lens. Cancel Adjustment” before this adjustment. 2) Select page: 0, address: 01, and set data: 01. Note 2: Check that the data of page: 6, address: 02 is “00”. 3) Select page: 5, address: F1, and set data: FF. If not, turn the power of unit OFF/ON. 4) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. Adjusting method: 5) Perform “ Data setting during camera system adjustment”. 1) Select page: 0, address: 01, and set data: 01. (Refer to page 5-13) 2) Select page: 5, address: F1, and set data: FF. 6) Select page: 6, address: 01, set data: A7, and press the PAUSE 3) Select page: D, address: 63, set data: 40, and press the PAUSE button. button of the adjusting remote commander. 7) Select page: F, address: 49 to 4C, and noting down the data 4) Perform “ Data setting during camera system adjustment”. of each address. (Refer to page 5-13) 8) Write data in page: F, address: 49 to 4C as shown in the fol- 5) Select page: 6, address: 01, set data: 11, and press the PAUSE lowing table. button. 6) Select page: 6, address: 01, set data: 0B, and press the PAUSE Address 49 4A 4B 4C button. (The auto white balance standard data input is per- formed and the standard data is stored in page: F, address: DSC-S30 28 00 62 C0Data 3A to 3D, 59) DSC-S50 28 80 5F 80 7) Select page: 6, address: 02, and check that the data is “01”. Note: After setting each data, be sure to press the PAUSE button Processing after Completing Adjustments: of the adjusting remote commander. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 9) Select page: 6, address: 01, set data: A5, and press the PAUSE button of the adjusting remote commander. button. (The auto white balance adjustment is performed and 2) Select page: 5, address: F1, and set data: 00. the adjustment data is stored in page: F, address: 3F, 40 and 3) Select page: D, address: 63, set data: 00, and press the PAUSE 80) button. 10) Select page: 6, address: 02, and check that the data is “01”. 4) Release the data setting performed at step 4). 11) Select page: 6, address: 01, set data: 3F, and press the PAUSE (Refer to page 5-13) button. 5) Select page: 0, address: 01, and set data: 00. 12) Select page: 0, address: 03, and set data: 04. 6) Perform “Auto White Balance Adjustment”. 13) Select page: 1, and check that the displayed data (Note 3) satisfies the R ratio specified value. 10. Auto White Balance Adjustment 14) Select page: 0, address: 03, and set data: 05. Adjust to the proper auto white balance output data. 15) Select page: 1, and check that the displayed data (Note 3) If it is not correct, auto white balance and color reproducibility satisfies the B ratio specified value. will be poor. 16) Select page: F, address: 49 to 4C, and input the data noted down at step 7). Mode STILL Note: After setting each data, be sure to press the PAUSE button Subject Clear chart of the adjusting remote commander. (Color reproduction adjustment frame) Processing after Completing Adjustments: Filter Filter C14 for color temperature 1) Select page: 0, address: 03, and set data: 00. correction 2) Select page: 6, address: 01, set data: 00, and press the PAUSE Measurement Point Displayed data of page: 1 (Note 3) button of the adjusting remote commander. Measuring Instrument Adjusting remote commander 3) Select page: 5, address: F1, and set data: 00. 4) Select page: D, address: 63, set data: 00, and press the PAUSE Adjustment Page F button. Adjustment Address 3F, 40, 80 5) Release the data setting performed at step 5). Specified Value DSC-S30 (Refer to page 5-13) R ratio: 2760 to 28A0 6) Select page: 0, address: 01, and set data: 00. B ratio: 6220 to 6360 DSC-S50 R ratio: 27E0 to 2920 B ratio: 5EE0 to 6020 5-19, 11. Color Reproduction Adjustment Adjust the color separation matrix coefficient so that proper color reproduction is produced. Mode STILL Subject Color bar chart (Color reproduction adjustment frame) Adjustment Page F Adjustment Address 41 to 48, 5C to 5F Note 1: Perform “Auto White Balance Standard Data Input” before this adjustment. Note 2: Check that the data of page: 6, address: 02 is “00”. If not, turn the power of unit OFF/ON. Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: FF. 3) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. 4) Perform “ Data setting during camera system adjustment”. (Refer to page 5-13) 5) Select page: 6, address: 01, set data: AB, and press the PAUSE button. 6) Select page: 6, address: 12, set data: 80, and press the PAUSE button. 7) Wait for 1 second. 8) Select page: 6, address: 12, set data: 00, and press the PAUSE button. 9) Wait for 2 seconds. 10) Select page: 6, address: 01, set data: A9, and press the PAUSE button. (The color reproduction adjustment is performed and the adjustment data is stored in page: F, address: 41 to 48, 5C to 5F) 11) Select page: 6, address: 02, and check that the data is “01”. Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button of the adjusting remote commander. 2) Select page: 5, address: F1, and set data: 00. 3) Select page: D, address: 63, set data: 00, and press the PAUSE button. 4) Release the data setting performed at step 4). (Refer to page 5-13) 5) Select page: 0, address: 01, and set data: 00. 6) Perform “Color Reproduction Check”. 5-20, 12. Color Reproduction Check For NTSC mode Mode STILL R-Y Subject Color bar chart (Color reproduction adjustment frame) Measurement Point Video terminal of A/V OUT jack MG (75 Ω terminated) R Measuring Instrument Vectorscope Specified Value All color luminance points shouldsettle within each color reproduction frame. YE B-Y Menu setting: 1) VIDEO OUT of SET UP menu B ... NTSC (NTSC mode) ... PAL (PAL mode) Checking method: G CY 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: FF. 3) Select page: D, address: 63, set data: 40, and press the PAUSE button of the adjusting remote commander. Burst position 4) Perform “ Data setting during camera system adjustment”. Fig. 5-1-16 (Refer to page 5-13) 5) Check that the picture frame is set to the specified position. (Refer to “6. picture Frame Setting” ) 6) Select page: 6, address: 10, and set data: 01. For PAL mode 7) Select page: E, address: 52, after noting down the data, set data: 0A, and press the PAUSE button. R-Y 8) Select page: 6, address: 01, set data: 0F, and press the PAUSE Burst position button. 9) Select page: 6, address: 12, set data: 80, and press the PAUSE button. MGR 10) Wait for 1 second. 11) Select page: 6, address: 12, set data: 00, and press the PAUSE button. 12) Wait for 2 seconds. YE 13) Check the each color luminance point in each color repro- duction frame. B-Y

B

Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE button of the adjusting remote commander. 2) Select page: 6, address: 10, and set data: 00. 3) Select page: E, address: 52, set data noted down at step 7) G CY and press the PAUSE button. 4) Select page: 5, address: F1, and set data: 00. 5) Select page: D, address: 63, set data: 00, and press the PAUSE button. 6) Release the data setting performed at step 4). Fig. 5-1-17 (Refer to page 5-13) 7) Select page: 0, address: 01, and set data: 00. 5-21, 13. White Balance Check Processing after Completing Adjustments: 1) Select page: 6, address: 01, set data: 00, and press the PAUSE Mode STILL button of the adjusting remote commander. Subject Clear chart 2) Select page: 6, adderss: 6C, and set data: 00. (Color reproduction adjustment frame) 3) Select page: E, address: 52, set data noted down at step 13) and press the PAUSE button. Measurement Point Displayed data of Video terminal of 4) Select page: E, address: 4B, set data noted down at step 23) Page: 1 (Note 2) A/V OUT jack and press the PAUSE button. (75 Ω terminated) 5) Select page: 5, address: F1, and set data: 00. Measuring Instrument Adjustment remote Vectorscope 6) Select page: D, address: 63, set data: 00, and press the PAUSE Commander button. Specified Value R ratio: 3E00 to 4200 Fig. 5-1-18 7) Release the data setting performed at step 5). B ratio: 3E00 to 4200 (A) and (B) (Refer to page 5-13) 8) Select page: 0, address: 01, and set data: 00. Note 1: Refer to “6. Picture Frame Setting” for XH, XL, YH and YL. R-Y Note 2: The right four digits of the page: 1 displayed data of the adjusting remote commander. 1:XX:XX Displayed data 4mm B-Y Checking method: 1) Check that the lens is not covered with either filter. 2) Select page: 0, address: 01, and set data: 01. 4mm 3) Select page: 5, address: F1, and set data: FF. 4) Select page: D, address: 63, set data: 40, and press the PAUSE Fig. 5-1-18 (A) button of the adjusting remote commander. 5) Perform “ Data setting during camera system adjustment”. (Refer to page 5-13) 6) Select page: 6, address: 90, and set data: XL. (Note 1) DSC-S30 7) Select page: 6, address: 91, and set data: XH. (Note 1) R-Y 8) Select page: 6, address: 92, and set data: YL. (Note 1) 9) Select page: 6, address: 93, and set data: YH. (Note 1) 1mm 10) Select page: 6, address: 6C, and set data: 01. 11) Select page: 6, address: 01, set data: 79, press the PAUSE B-Y button, and wait for 1 second. 2.5mm 12) Select page: 6, address: 2C, and set data: 01. 6mm • INDOOR data check 13) Select page: E, address: 52, after noting down the data, set data: 0E, and press the PAUSE button. 6mm 14) Select page: 6, address: 01, set data: 0F, and press the PAUSE button. 15) Select page: 0, address: 03, and set data: 04. DSC-S50 16) Select page: 1, and check that the displayed data (Note 2) R-Y satisfies the R ratio specified value. 17) Select page: 0, address: 03, and set data: 05. B-Y 18) Select page: 1, and check that the displayed data (Note 2) satisfies the B ratio specified value. 4mm • INDOOR luminance point check 19) Select page: 6, address: 1C, and set data: 00. 8mm 20) Select page: 0, address: 03, and set data: 00. 21) Check that the center of the white luminance point is within the circle shown Fig. 5-1-18 (A). 8mm • OUTDOOR luminance point check 22) Place the C14 filter on the lens. Fig. 5-1-18 (B) 23) Select page: E, address: 4B, after noting down the data, set data: 20, and press the PAUSE button. 24) Select page: 6, address: 01, set data: 3F, and press the PAUSE button. 25) Check that the center of the white luminance point settles in the circle shown Fig. 5-1-18 (B). 5-22, 14. Strobe White Balance Adjustment 15. Strobe Light Level and White balance Check Adjust the white balance when the strobe light flashed. Check the light level regulation and the white balance when the strobe light flashed. Mode STILL Subject Flash adjustment box (Note 3) Mode STILL (1.0 m from the front of lens) Subject Flash adjustment box (Note 3) Adjustment Page F (1.0 m from the front of lens) Adjustment Address 4D, 4E, 64, 69, 6A, 6B Measurement Point Displayed data of page: 1 Note 1: Perform “HALL Adjustment”, “Flange Back Adjust- Measuring Instrument Adjusting remote commander ment”, “Light Level Adjustment”, “Auto White Balance Specified value Y level data: 60 to 94 Adjustment” and “Auto White Balance Standerd Data In- R-Y level data: FA to FF or 00 to 06 put” before this adjustment. (Note 4) Note 2: Perform this adjustment in the Flash adjustment box. B-Y level data: FA to FF or 00 to 06 Note 3: Refer to “4. Preparing the Flash adjustment box”. (Note 4) (See page 5-7) Note 1: Perform this checking successively after performing Note 4: Check that the data of page: 6, address: 02 is “00”. “HALL Adjustment”, “Flange Back Adjustment”, “ Light If not, turn the power of unit OFF/ON. Level Adjustment”, “Strobe White Balance Adjustment” and “Auto White Balance Standerd Data Input”. (Do not Switch setting: turn the power of unit OFF) 1) FLASH ... ON Note 2: Perform this adjustment in the Flash adjustment box. Note 3: Refer to “4. Preparing the Fiash adjustment box”. Adjusting method: (See page 5-7) 1) Select page: 0, address: 01, and set data: 01. Note 4: The right four digits of the page: 1 displayed data of the 2) Select page: 5, address: F1, and set data: FF. adjusting remote commander. 3) Select page: D, address: 63, set data: 40, and press the PAUSE 1:XX:XX button of the adjusting remote commander. B-Y level data 4) Perform “ Data setting during camera system adjustment”. R-Y level data (Refer to page 5-13) Note 5: Displayed data of page: F, address: 64 of the adjusting 5) Select page: 7, address: 03, and set data: 08. remote commander. 6) Select page: 6, address: 90, and set data: 00. F:XX:64 7) Select page: 6, address: 91, and set data: 00. Y level data 8) Select page: 6, address: 92, and set data: 00. Note 6: Check that the data of page: 6, address: 02 is “00”. 9) Select page: 6, address: 93, and set data: 80. 10) Select page: 6, address: 6C, and set data: 01. Checking method: 11) Select page: 6, address: 2C, and set data: 01. 1) Select page: 0, address: 01, and set data: 01. 12) Select page: 6, address: 01, set data: 79, and press the PAUSE 2) Select page: 6, address: 01, set data: 79, and press the PAUSE button. button of the adjusting remote commander. 13) Select page: 6, address: 01, set data: 67, and press the PAUSE 3) Select page: 6, address: 01, set data: 67, and press the PAUSE button. button. 14) Select page: 6, address: 01, set data: 00, and press the PAUSE 4) Check the flashing of strobe light. button. 5) Select page: F, address: 64, and check that the data satisfies 15) Select page: 6, address: 01, set data: 79, and press the PAUSE the Y level data specified value. (Note 5) button. 16) Select page: 6, address: 01, set data: 67, and press the PAUSE 6) Select page: 0, address: 03, and set data: 02. button. 7) Select page: 1, and check the R-Y, B-Y level data (Note 4) 17) Select page: 6, address: 01, set data: 00, and press the PAUSE satisfies the specified value. button. 18) Select page: 6, address: 01, set data: 79, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: 0, address: 03, and set data: 00. 19) Select page: 6, address: 01, set data: B9, and press the PAUSE 2) Select page: 6, address: 01, set data: 00, and press the PAUSE button. (The strobe white balance adjustment is performed button of the adjusting remote commander. and the adjustment data is stored in page: F, address: 4D, 4E, 3) Select page: 6, address: 2C, and set data: 00. 64, 69, 6A and 6B) 4) Select page: 6, address: 6C, and set data: 00. 20) Select page: 6, address: 02, and check that the data is “01”. 5) Select page: 6, address: 93, and set data: 00. 6) Select page: 7, address: 03, set data: 00, and press the PAUSE Processing after Completing Adjustments: button. 1) Select page: 6, address: 01, set data: 00, and press the PAUSE 7) Select page: 5, address: F1, and set data: 00. button of the adjusting remote commander. 8) Select page: D, address: 63, set data: 00, and press the PAUSE 2) Perform “Strobe Light Level and White Balance Check” suc- button. cessively. (Do not turn the power of unit OFF) 9) Release thedata setting performed at step 4) of “Strobe White Balance Adjustment”. (Refer to page 5-13) 10) Select page: 0, address: 01, and set data: 00. 5-23, 16. CCD Black Defect Compensation 9) Release the data setting performed at step 4). (Refer to page 5-13) Mode STILL 10) Select page: 0, address: 01, and set data: 00. Subject Clear chart (25 cm from the front of lens) 17. CCD White Defect Compensation Measurement Point Displayed data of page: 6, address: 55 Measuring Instrument Adjusting remote commander Mode STILL Adjustment Page 7 Subject Clear chart Adjustment Address 60 to 87 (25 cm from the front of lens) Measurement Point Displayed data of page: 6, address: 55 Note 1: Check that there are no dust, no dirt and reflection of the Measuring Instrument Adjusting remote commander clear chart. Note 2: Any subject other than the clear chart should be in the Adjustment Page 7 screen. Adjustment Address 88 to A3 Adjusting method: Note 1: Check that there are no dust, no dirt and reflection of the 1) Select page: 0, address: 01, and set data: 01. clear chart. 2) Select page: 5, address: F1, and set data: FF. Note 2: Any subject other than the clear chart should be in the 3) Select page: D, address: 63, set data: 40, and press the PAUSE screen. button of the adjusting remote commander. 4) Perform “ Data setting during camera system adjustment”. Adjusting method: (Refer to page 5-13) 1) Select page: 0, address: 01, and set data: 01. 5) Select page: F, address: DF, after noting down the data, set 2) Select page: 5, address: F1, and set data: FF. data: 4C, and press the PAUSE button. 3) Select page: D, address: 63, set data: 40, and press the PAUSE 6) Select page: 6, address: 2C, and set data: 01. button of the adjusting remote commander. 7) Select page: 6, address: 90, and set data: 00. 4) Perform “ Data setting during camera system adjustment”. 8) Select page: 6, address: 91, and set data: 03. (Refer to page 5-13) 9) Select page: 6, address: 92, and set data: 00. 5) Select page: F, address: DE, after noting down the data, set 10) Select page: 6, address: 93, and set data: 00. data: 1E, and press the PAUSE button. 11) Select page: 6, address: 6C, and set data: 01. 6) Select page: F, address: E3, after noting down the data, set 12) Select page: 6, address: 01, set data: 79, and press the PAUSE data: 08, and press the PAUSE button. button. 7) Select page: 6, address: 01, set data: 8B, and press the PAUSE 13) Select page: 6, address: 30, and set data: 01. button. (The CCD white defect compensation is performed 14) Wait 4 seconds. and the compensation data is stored in page: 7, address: 88 15) Select page: 6, address: 01, set data: 8D, and press the PAUSE to A3) button. (The CCD black defect compensation is performed 8) Select page: 6, address: 02, and check that the data is “01”. and the compensation data is stored in page: 7, address: 60 9) Select page: 6, address: 55, and check the data. to 87) 00 to 7F: Normal 16) Select page: 6, address: 02, and check that the data is “01”. 80 to FF: Defective 17) Select page: 6, address: 55, and check the data. 10) Select page: 6, address: 01, set data: 00, and press the PAUSE 00 to 0A: Normal button. 0B to FF: Defective 11) Select page: F, address: DE, set data: 0F, and press the PAUSE 18) Select page: 6, address: 01, set data: 00, and press the PAUSE button. button. 12) Select page: F, address: E3, set data: A0, and press the PAUSE 19) Select page: F, address: DF, set data: 5A, and press the PAUSE button. button. 13) Select page: 6, address: 01, set data: 87, and press the PAUSE 20) Select page: 6, address: 01, set data: 89, and press the PAUSE button. button. 14) Select page: 6, address: 02, and check that the data is “01”. 21) Select page: 6, address: 02, and check that the data is “01”. 15) Select page: 6, address: 55, and check the data. 22) Select page: 6, address: 55, and check the data . 00: Normal 00: Normal 01 to FF: Defective 01 to FF: Defective Processing after Completing Adjustments: Processing after Completing Adjustments: 1) Select page: F, address: DE, set data noted down at step 5) 1) Select page: F, address: DF, set data noted down at step 5) and press the PAUSE button of the adjusting remote com- and press the PAUSE button of the adjusting remote mander. commander. 2) Select page: F, address: E3, set data noted down at step 6) 2) Select page: 6, address: 01, set data: 00, and press the PAUSE and press the PAUSE button. button. 3) Select page: 6, address: 01, set data: 00, and press the PAUSE 3) Select page: 6, address: 2C, and set data: 00. button. 4) Select page: 6, address: 30, and set data: 00. 4) Select page: 5, address: F1, and set data: 00. 5) Select page: 6, address: 6C, and set data: 00. 5) Select page: D, address: 63, set data: 00, and press the PAUSE 6) Select page: 6, address: 91, and set data: 00. button. 7) Select page: 5, address: F1, and set data: 00. 6) Release the data setting performed at step 4). 8) Select page: D, address: 63, set data: 00, and press the PAUSE (Refer to page 5-13) button. 7) Select page: 0, address: 01, and set data: 00. 5-24, 1-5. LCD SYSTEM ADJUSTMENTS [Adjusting connector] Most of the measuring points for adjusting the LCD system are Before perform the LCD system adjustments, check that the concentrated in CN709 of the SY-58 board. specified values of “VIDEO SYSTEM ADJUSTMENTS” are sat- Connect the Measuring Instruments via the CPC-9 jig (J-6082- isfied. 393-C). The following table shows the Pin No. and signal name of CN709. Note 1: The back light (fluorescent tube) is driven with high volt- age AC power. Therefore, do not touch the back light Pin No. Signal Name Pin No. Signal Name directly, otherwise you will feel an electric shock. 1 N. C. 10 UNREG Note 2: Taken an extreme care not to destroy the liquid crystal 2 N. C. 11 LANC IN display module by static electricity when replacing it. Note 3: Set the LCD BRIGHT to the center. 3 N. C. 12 LANC OUT 4 REG GND 13 N. C. 5 XCPC_IN 14 RF7 6 N. C. 15 TXD 7 HSY 16 RXD 8 PANEL COM 17 RESET 9 VG 18 VDD Table 5-1-7 • ATTACHMENT OF CPC-9 JIG BT holder assembly Open the battery lid assembly SY-58 board (CN709) CPC lid CPC lid (Note 3) 18 CPC-9 jig (J-6082-393-C) (18P flexible board) (Note 1, 2) Note 1: Don’t use the 12 pin flexible board of CPC-9 jig. It causes damage to the unit. Note 2: The old CPC-9 jig (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Note 3: In removing the CPC lid, start from the upper side. Fig. 5-1-19 5-25, 1. LCD Initial Data Input 2. VCO Adjustment (PD-127 Board) Set the VCO free-run frequency. If deviated, the LCD screen will Mode PLAY be blurred. Signal Arbitrary Mode PLAY Adjustment Page D Signal Arbitrary Adjustment Address 1C, 1C, D0 to D8, DD to DF Measurement Point Pin 7 of CN709 (HSY) on SY- 58 board Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Measuring Instrument Frequency counter 2) Select page: D, and enter the data given in the following table. Adjustment Page D Specified Value D7 (NTSC) Note: Press the PAUSE button of the adjusting remote commander DD (PAL) each time the data are set, as the data are written to non- volatile memory (EEPROM). Specified Value f = 15734 ± 30 Hz (NTSC) f = 15745 ± 30 Hz (PAL) Address Data Remark Menu setting: 1C 02 Fixed value 1) VIDEO OUT of SET UP menu... NTSC (NTSC mode) (This adjustment must be performed in NTSC mode, so don't 1D 2C set the menu setting to “PAL”) D0 BC Bright Adjustment D1 80 Color Adjustment Adjusting method: D2 B9 White Balance Adjustment 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F0, and set data: 01. D3 B7 3) Select page: D, address: D7, change the data and set the fre- D4 BE Contrast Adjustment quency (f) to the NTSC specified value. D5 C8 D Range Adjustment 4) Press the PAUSE button of the adjusting remote commander. 5) Select page: D, address: DD, and change the data and set the D6 7C V-COM Level Adjustment frequency (f) to the PAL specified value. D7 80 VCO Adjutment (NTSC) 6) Press the PAUSE button of the adjusting remote commander. D8 74 V-COM Adjustment Processing after Completing Adjustments: DD 88 VCO Adjutment (PAL) 1) Select page: 5, address: F0, and set data: 00. DE 13 Fixed value 2) Select page: 0, address: 01, and set data: 00. DF 11 Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 00. 5-26, 3. D Range Adjustment (PD-127 Board) 4. Bright Adjustment (PD-127 Board) Set the D range of the LCD driver to the specified value. Set the level of the VIDEO signal for driving the LCD to the speci- If deviated, the LCD screen will became blackish or saturated fied value. (whitish) If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitrary Mode PLAY Measurement Point Pin 9 of CN709 (VG) on SY-58 Signal Arbitrary board Measurement Point Pin 9 of CN709 (VG) on SY-58 External trigger: Pin 8 of CN709 board (PANEL COM) on SY-58 board External trigger: Pin 8 of CN709 Measuring Instrument Oscilloscope (PANEL COM) on SY-58 board Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D5 Adjustment Page D Specified Value A = 3.62 ± 0.05 Vp-p Adjustment Address D0 Specified Value A = 1.85 ± 0.08 Vp-p Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F1, and set data: 03. 1) Select page: 0, address: 01, and set data: 01. 3) Select page: D, address: D5, change the data and set the volt- 2) Select page: 5, address: F1, and set data: 03. age (A) between the reversed waveform pedestal and non-re- 3) Select page: 2, address: 10, and set data: 01. versed waveform pedestal to the specified value. 4) Select page: D, address: D0, change the data and set the volt- 4) Press the PAUSE button of the adjusting remote commander. age (A) between the pedestal and GAMMA 1 limiter level to the specified value. Processing after Completing Adjustments: 5) Press the PAUSE button of the adjusting remote commander. 1) Select page: 5, address: F1, and set data: 00. 2) Select page: 0, address: 01, and set data: 00. Processing after Completing Adjustments: 1) Select page: 5, address: F1, and set data: 00. Pedestal 2) Select page: 2, address: 10, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. GAMMA1 limiter level

A A

Pedestal 2H Pedestal 2H A: Pedestal level difference between 1H period and previous 1H period. Fig. 5-1-21 Fig. 5-1-20 5-27, 5. Contrast Adjustment (PD-127 Board) 6. Color Adjustment (PD-127 Board) Set the level of the VIDEO signal for driving the LCD to the speci- Set the color saturation to the standard value. fied value. If, deviated, the color will be dark or light. If deviated, the LCD screen image will be blackish or saturated (whitish). Mode PLAY Signal Arbitrary Mode PLAY Measurement Point Pin 9 of CN709 (VG) on SY-58 Signal Arbitrary board Measurement Point Pin 9 of CN709 (VG) on SY-58 External trigger: Pin 8 of CN709 board (PANEL COM) on SY-58 board External trigger: Pin 8 of CN709 Measuring Instrument Oscilloscope (PANEL COM) on SY-58 board Adjustment Page D Measuring Instrument Oscilloscope Adjustment Address D1 Adjustment Page D Specified Value A = 544 ± 50 mVp-p Adjustment Address D4 Specified Value A = 3.31 ± 0.07 Vp-p Adjusting method: 1) Select page: 0, address: 01, and set data: 01. Adjusting method: 2) Select page: 5, address: F1, and set data: 04. 1) Select page: 0, address: 01, and set data: 01. 3) Select page: D, address: D1, change the data and set the volt- 2) Select page: 5, address: F1, and set data: 03. age (A) between the white 100% (Reference level) and green 3) Select page: D, address: D4, change the data and set the volt- to the specified value. age (A) between the pedestal and 10 steps peak to the speci- 4) Press the PAUSE button of the adjusting remote commander. fied value. 4) Press the PAUSE button of the adjusting remote commander. Processing after Completing Adjustments: 1) Select page: 5, address: F1, and set data: 00. Processing after Completing Adjustments: 2) Select page: 0, address: 01, and set data: 00. 1) Select page: 5, address: F1, and set data: 00. 2) Select page: 0, address: 01, and set data: 00. White 100% Green 10 steps peak

A A

2H Pedestal 2H Fig. 5-1-23 Fig. 5-1-22 5-28, 7. V-COM Level Adjustment (PD-127 Board) 8. V-COM Adjustment (PD-127 Board) Set the common electrode drive signal level of LCD to the speci- Set the DC bias of the common electrode drive signal of LCD to fied value. the specified value. If deviated, the LCD display will be move, producing flicker and Mode PLAY conspicuous vertical lines. Signal Arbitrary Mode PLAY Measurement Point Pin 8 of CN709 (PANEL COM) on SY-58 board Signal Arbitrary Measuring Instrument Oscilloscope Measurement Point Check on LCD screen Adjustment Page D Measuring Instrument Adjustment Address D6 Adjustment Page D Specified Value A = 6.50 ± 0.05 Vp-p Adjustment Address D8 Specified Value The brightness difference Adjusting method: between the section-A and 1) Select page: 0, address: 01, and set data: 01. section-B is minimum 2) Select page: 5, address: F1, and set data: 03. 3) Select page: D, address: D6, change the data and set the V- Note: Perform “Bright Adjustment” and “Contrast Adjustment” COM signal level (A) to the specified value. before this adjustment. 4) Press the PAUSE button of the adjusting remote commander. Adjusting method: Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 01. 1) Select page: 5, address: F1, and set data: 00. 2) Select page: 5, address: F1, and set data: 01. 2) Select page: 0, address: 01, and set data: 00. 3) Select page: 2, address: 10, and set data: 02. 4) Select page: D, address: D8, change the data so that bright- ness of the section A and section B is equal. 5) Press the PAUSE button of the adjusting remote commander. Processing after Completing Adjustments: 1) Select page: 5, address: F1, and set data: 00.

A

2) Select page: 2, address: 10, and set data: 00. 3) Select page: 0, address: 01, and set data: 00. B A 2H Fig. 5-1-24ABBAABFig. 5-1-25 5-29, 9. White Balance Adjustment (PD-127 Board) Correct the white balance. If deviated, the LCD screen color cannot be reproduced. Mode PLAY Signal Arbitrary Measurement Point Check on LCD screen Measuring Instrument Adjustment Page D Adjustment Address D2, D3 Specified Value LCD screen must not be colored Note: Check the white balance only when replacing the follow- ing parts. If necessary, adjust them. 1. LCD panel 2. Light induction plate 3. IC802 Adjusting method: 1) Select page: 0, address: 01, and set data: 01. 2) Select page: 5, address: F1, and set data: 02. 3) Select page: D, address: D2 and D3, and set the data to the initial value. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. Address Data D2 B9 D3 B7 4) Check that the LCD screen is not colored. If colored, change the data of page: D, address: D2 and D3 so that the LCD screen is not colored. Note: To write in the non-volatile memory (EEPROM), press the PAUSE button of the adjustment remote commander each time to set the data. 5) Select page: 5, address: F1, and set data: 00. 6) Select page: 0, address: 01, and set data: 00. 5-30, 1-6. SYSTEM CONTROL SYSTEM ADJUSTMENTS Adjusting method: 1. Battery Down Adjustment 1) Adjust the output voltage of the regulated power supply so Set the battery end voltage. that the digital volt meter display is 7.2 ± 0.1 Vdc. If the voltage is incorrect, the life of battery will shorten. 2) Turn off the power supply. The image at the battery end will also be rough. 3) Turn the HOLD switch of the adjusting remote commander. 4) Turn on the power supply. Mode STILL 5) Insert the memory stick to the unit, and set the STILL mode. Subject Arbitrary 6) Set the FOCUS switch in MANUAL mode. 7) Select page: 0, address: 01, and set data: 01. Measurement Point Displayed data of page: 2, 8) Decrease the output voltage of the regulated power supply so address: 51 that the digital voltmeter display is 5.30 ± 0.01 Vdc. Measuring Instrument Adjusting remote commander 9) Select page: 2, address: 51, read the data, and this data is named Adjustment Page D Dref. 10) Select page: D, address: 90, set data Dref, and then press the Adjustment Address 90 to 94 PAUSE button of adjusting remote commander. (The data of address: 90, should be “7E” to “8F”) Connection: 11) Convert Dref to decimal notation, and obtain Dref’. 1) Connect the regulated power supply and the digital voltmeter (Refer to Table 5-2-2. “Hexadecimal-decimal conversion to the battery terminal as shown in Fig. 5-1-26. table”) 12) Calculate D91’, D92’, D93’ and D94’ using following equations (decimal calculation), convert it to a hexadecimal number, and input each adjustment address. Address: 91 D91’ = Dref’+8 Address: 92 D92’ = Dref’+23 Address: 93 D93’ = Dref’+44 Address: 94 D94’ = Dref’+55 Note: After setting each data, be sure to press the PAUSE button. Processing after Completing Adjustments: 1) Select page: 0, address: 01, and set data: 00. Note : The old CPC-9 jit (Parts code: J-6082-393-B) cannot be used, because it cannot operate the adjustment remote commander. Regulated power supply (5.30 ± 0.01 V DC) Adjustment remote commander12CN101 Digital voltmeter CPC-9 jig (J-6082-393-C) DC power supply (6.0 to 7.2 V DC) MS-50 board SY-58 board (CN709) Fig. 5-1-26 5-31, 5-2. SERVICE MODE • Changing the address 2-1. ADJUSTING REMOTE COMMANDER The address increases when the FF (M) button is pressed, The adjusting remote commander is used for changing the calcu- and decreases when the REW (M) button is pressed. There lation coefficient in signal processing, EVR data, etc. The adjust- are altogether 256 addresses, from 00 to FF. ing remote commander performs bi-directional communication • Changing the data (Data setting) with the unit using the remote commander signal line (LANC). The data increases when the PLAY (N) button is pressed, The resultant data of this bi-directional communication is written and decreases when the STOP (x) button is pressed. There in the non-volatile memory. are altogether 256 data, from 00 to FF. • Writing the adjustment data 1. Used Adjusting Remote Commander The PAUSE button must be pressed to write the adjustment 1) Connect the adjusting remote commander to the CN709 on data in the nonvolatile memory. (The new adjustment data the SY-58 board via CPC-9 jig (J-6082-393-C). will not be recorded in the nonvolatile memory if this step is 2) Adjust the HOLD switch of the adjusting remote commander not performed) to “HOLD” (SERVICE position). 3) Turn on the power with the POWER switch of the unit. 2. Precautions upon Using the Adjusting Remote If it has been properly connected, the LCD on the adjusting re- Commander mote commander will display as shown in Fig. 5-2-1. Mishandling of the adjusting remote commander may erase the correct adjustment data at times. To prevent this, it is recommended that all adjustment data be noted down before beginning adjust- ments and new adjustment data after each adjustment. 0 : 00 : 00 Page Data Address Fig. 5-2-1 4) Operate the adjusting remote commander as follows. • Changing the page The page increases when the EDIT SEARCH + button is pressed, and decreases when the EDIT SEARCH – button is pressed. There are altogether 16 pages, from 0 to F. Hexadecimal0123456789ABCDEFnotation LCD Display0123456789AbcdEFDecimal notation0123456789101112131415 conversion value Table 5-2-1 5-32, 2-2. DATA PROCESS The calculation of the adjusting remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data. Table 5-2-2. indicates the hexadecimal notation- the deci- mal notation, calculation table. Hexadecimal nontation-Decimal notation 2 ↓ The lower digits of the0123456789ABCDEFhexadecimal notation The upper digits of the (A) (b) (c) (d) (E) (F) hexadecimal notation0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 1→ B (b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note : ( ) indicate the adjusting remote control unit display. (Example) In the case that the adjusting remote control unit display are BD (bd). As the upper digit of the hexadecimal notation is B (b), and the lower digit is D (d), the intersection “189” of the1 and 2 in the above table is the decimal notation to be calculated. Table 5-2-2 5-33, 2-3. SERVICE MODE 3. Switch Check (1) 1. Setting the Test Mode Page 2 Address 43 Page D Address 10 Bit Function When bit value=1 When bit value=0 Data Function SHUTTR SW 00 Normal 1 ( Control Switch Block) OFF ON 01 Forced STILL mode power ON Mode SW 02 Forced PLAY mode power ON XSHUTTER LOCK SW 2 Control Switch Block 03 Forced MOVIE mode power ON ( ) OFF ON Mode SW • Before setting the data, select page: 0, address: 01, and set data: 01. Using method: • For page D, the data set is recorded in the non-volatile memory 1) Select page: 2, address: 43 by pressing the PAUSE button of the adjusting remote com- 2) By discriminating the bit value of dispaly data, the state of the mander. In this case, take note that the test mode will not be switches can be discriminated. exited even when the main power is turned off. • After completing adjustments/repairs, be sure to return the data of this address to “00”, and press the PAUSE button of the ad- justing remote commander. Select page: 0, address: 01, and set data: 00. 2. Bit Value Discrimination Bit values must be discriminated using the display data of the ad- justing remote commander for following items. Use the table be- low to discriminate if the bit value is “1” or “0” Display on the adjustilng remote commander 0 : 00 : 00 Address Page bit3 to bit0 discrimination bit7 to bit4 discrimination Display on the Bit values Adjusting bit3 bit2 bit1 bit0 remote or or or or commander bit7 bit6 bit5 bit40000010001200103001140100501016011070111A8100091001A(A) 1010B(b) 1011C(c) 1100D(d) 1101BE(E) 1110F(F) 1111Example: If “8E” is displayed on the adjusting remote com- mander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. 5-34, 4. Switch Check (2) Page 2 Address 54 to 57 Using method: 1) Select page: 2, addresses: 54 to 57. 2) By discriminating the dispaly data, the pressed key can be discriminated. Data Address 00 to 14 15 to 33 3C to 64 65 to 91 92 to BD BE to E9 EA to FF 54 PANEL REVERSE (KEY AD0) (JK-11 board) (IC404 uk) (S301) 55 CONTROL DOWN CONTROL UP DISPLAY PROGRAM AE+ PROGRAM AE– PANEL ON/OFF (KEY AD1) (SW-339 board) (SW-339 board) (SW-339 board) (SW-339 board) (SW-339 board) (SW-339 board) (IC404 ul) (S101) (S101) (S102) (S105) (S108) (S110) 56 CONTROL RIGHT CONTROL LEFT CONTROL SET FLASH FOCUS (KEY AD2) (SW-339 board) (SW-339 board) (SW-339 board) (SW-339 board) (SW-339 board) (IC404 i;) (S101) (S101) (S101) (S103) (S107) 57 PROGRAM AE PANEL UP/DOWN (KEY AD3) (SW-339 board) (SW-339 board) (IC404 ia) (S104) (S106) 5. LED Check Page 2 Address 06 Data 02 Using method: 1) Select page: 2, address: 06, and set data: 01. 2) Check that all LED except for the ACCESS LED are lit. 3) Select page: 2, address: 06, and set data: 00. 6. LCD Check Page 2 Address 06 Data 02 Using method: 1) Select page: 2, address: 05, and set data: 02. 2) Check that all LED are lit and all segments of LCD (display window) are lit. 3) Select page: 2, address: 05, and set data: 00. 55-3-355 E,

DSC-S30/S50 SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS The components identified by mark 0 or dotted line with mark 0 are NOTE: critical for safety. • -XX and -X mean standardized parts, so they may • Items marked “*” are not stocked since they are Replace only with part number speci-fied. have some difference from the original one. seldom required for routine service. Some delay • Color Indication of Appearance Parts should be anticipated when ordering these items. Les composants identifiés par une Example: • The mechanical parts with no reference number in marque 0 sont critiquens pour lasécurité. KNOB, BALANCE (WHITE) .(RED) the exploded views are not supplied. Ne les remplacer que par une pièce ↑ ↑ • Accessories are given in the last of the electrical portant le numéro spécifié. Parts Color Cabinet's Color parts list. 6-1-1. FRONT PANEL SECTION not 10 supplied 11 12 4 Main section 8 not (See page 6-2) supplied not 4 supplied6914 BZ901 not 15 13 supplied 5 (S50) 4 18 SP901 3 13 19 17 not supplied 2 MIC901 4 13 16 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3950-656-1 CABINET (FRONT) ASSY (S50) 10 X-3950-665-1 CABINET (UPPER) ASSY (S30) 1 X-3950-664-1 CABINET (FRONT) ASSY (S30) 11 3-060-275-01 KNOB, MODE 2 3-061-075-01 LABEL, LENS 12 3-061-115-01 BRACKET, STRAP 3 3-061-675-01 RING, ORNAMENTAL 13 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 4 3-968-729-91 SCREW (M2), LOCK ACE, P2 14 1-476-038-11 SWITCH BLOCK, CONTROL (MODE SW) 5 3-060-251-01 LID, CPC 015 1-476-005-11 FLASH UNIT 6 3-050-594-01 SPRING, COMPRESSION 16 3-061-114-01 HOLDER, MISP (S50) 7 3-061-076-01 LID, BATTERY (S50) * 17 3-055-971-01 CUSHION, MICROPHONE (S50) 7 3-061-076-11 LID, BATTERY (S30) * 18 3-061-077-01 PLATE (1), GROUND 8 3-060-284-11 SLIDER, BT LOCK (S50) 19 3-060-274-01 SCREW, TRIPOD 8 3-060-284-21 SLIDER, BT LOCK (S30) BZ901 1-529-739-11 BUZZER, PIEZOELECTRIC (S30) 9 3-318-382-01 SCREW (1.7X3), TAPPING MIC901 1-542-428-11 MICROPHONE UNIT (S50) 10 X-3950-659-1 CABINET (UPPER) ASSY (S50) SP901 1-505-862-41 SPEAKER (2.0 cm) (S50) 6-1, 6-1-2. MAIN SECTION 59 Rear cabinet section (See page 6-3)

A

52 70 52 BT901 58 52 57 55

A

55 52 64 52 52 56 65 not supplied 68 Lens block assembly 66 (See page 6-4) not supplied The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3950-655-1 HOLDER ASSY, BT 060 1-794-045-11 CONNECTOR, DC-IN 52 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 61 1-678-002-11 FP-025 FLEXIBLE BOARD 53 A-7074-427-A MS-50 BOARD, COMPLETE 62 3-061-157-11 BUTTON, FUNCTION 54 3-969-380-01 SPRING, BATTERY 63 A-7074-431-A SW-339 BOARD, COMPLETE 55 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 64 1-678-003-11 FP-026 FLEXIBLE BOARD 56 A-7074-426-A DD-141 BOARD, COMPLETE (S50) 65 A-7074-428-A JK-194 BOARD, COMPLETE 56 A-7074-434-A DD-141 BOARD, COMPLETE (S30) * 66 3-061-069-01 FRAME, JK 57 1-677-877-11 FP-024 FLEXIBLE BOARD * 67 3-060-250-01 FRAME, SD 58 A-7096-244-A SY-58 BOARD, COMPLETE (SERVICE) (S50) 68 1-960-457-11 HARNESS (YP-052) 58 A-7096-245-A SY-58 BOARD, COMPLETE (SERVICE) (S30) * 69 3-062-774-01 SHEET (SH) 59 1-476-039-11 SWITCH BLOCK, CONTROL * 70 3-061-699-01 SY SHEET (260) (ZOOM/POWER SW) BT901 1-694-654-11 TERMINAL BOARD, BATTERY 6-2, 6-1-3. REAR CABINET SECTION LCD901 ND901 111 113 113 115 119 A 118 110 115 133 109 110 108 122 107 108 123 106 124

A

126 125 104 135 103 129 not supplied 102 134 108 128 The components identified by Les composants identifiés par une 101 mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 3-061-079-01 COVER (T), HINGE 119 A-7074-436-A PD-127 BOARD, COMPLETE (S30) * 102 3-061-083-01 CLIP, KJ 120 1-960-472-11 HARNESS (YP-053) 103 A-7074-432-A KJ-11 BOARD, COMPLETE 121 1-960-473-11 HARNESS (YP-054) 104 1-960-474-11 HARNESS (SK-100) 122 3-060-299-12 KNOB, POWER * 105 3-061-082-01 HOLDER, KJ 123 3-318-382-02 SCREW (1.7), TAPPING 106 X-3950-657-1 HINGE ASSY 124 3-061-108-01 HOLDER, LOCK 107 3-061-084-01 COVER (B), HINGE 125 3-061-107-01 LEVER, LOCK 108 3-061-216-01 ACE (M1.7), SPECIAL HEAD LOCK 126 3-061-109-01 SPRING, LOCK 109 X-3950-658-1 CABINET (REAR) ASSY (S50) 127 3-959-978-02 CUSHION, PANEL 109 X-3950-794-1 CABINET (REAR) ASSY (S30) 128 3-061-096-01 LID, JK 110 3-968-729-91 SCREW (M2), LOCK ACE, P2 129 3-051-520-01 SPRING, POWER 111 3-061-080-01 CABINET (REAR), P 130 3-060-297-01 HOLDER, POWER 0112 1-418-879-21 TRANSFORMER UNIT, INVERTER 131 3-061-111-01 COVER, DC * 113 3-051-232-01 CLIP, PCB * 132 3-062-825-01 SHEET, KJ 114 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION * 133 3-062-736-01 SHEET, ELECTROSTATIC 115 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 134 3-061-113-01 HOLDER, SLIDE KNOB 116 3-973-497-91 SCREW (M1.7), 0-NO. +P 2 135 3-061-112-01 KNOB, SLIDE 117 3-061-078-01 CABINET (FRONT), P 136 3-060-295-01 SHEET (BL) * 118 3-061-081-01 PLATE, BL FIXED LCD901 1-803-857-21 INDICATOR MODULE LIQUID CRYSTAL 119 A-7074-430-A PD-127 BOARD, COMPLETE (S50) 0ND901 1-517-878-31 TUBE, FLUORESCENT, COLD CATHODE 6-3, 6-1-4. LENS BLOCK ASSEMBLY 155 156 154 156 IC301 161 160 M901 M902 (Note) Be sure to read “Precuations for Replcement of CCD Imager” on page 4-8 when changing the CCD imager Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 1-758-415-11 LENS, ZOOM (VCL-6103WA) 160 3-060-714-01 RUBBER (CL), SEAL 154 3-061-122-01 SHEET, LENS 161 1-758-435-11 FILTER BLOCK, OPTICAL (S30) 155 3-061-121-01 FRAME (260), LENS 161 1-758-436-11 FILTER BLOCK, OPTICAL (S50) 156 3-914-366-01 SCREW (DIA. 1.7X4), PRECISION 162 3-058-032-01 ADAPTOR (CL), CCD FITTING 157 1-678-001-11 FP-023 FLEXIBLE BOARD IC301 A-7031-090-A CCD BLOCK ASSY (CCD IMAGER) (S30) 158 3-947-268-11 TITE (2), +B TAPPING (P) IC301 A-7031-092-A CCD BLOCK ASSY (CCD IMAGER) (S50) 159 A-7074-429-A CD-262 BOARD, COMPLETE (S50) M901 3-709-573-01 MOTOR UNIT, FOCUS 159 A-7074-435-A CD-262 BOARD, COMPLETE (S30) M902 3-709-574-01 MOTOR UNIT, ZOOM 6-4,

CD-262 DD-141

6-2. ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by parts list may be different from the parts speci- are seldom required for routine service. mark 0 or dotted line with mark 0 are critical for safety. fied in the diagrams or the components used Some delay should be anticipated when order- Replace only with part number on the set. ing these items. specified. • -XX and -X mean standardized parts, so they • SEMICONDUCTORS Les composants identifiés par une may have some difference from the original In each case, u: µ, for example: marque 0 sont critiquens pour la one. uA.: µA.uPA.: µPA.sécurité. • RESISTORS uPB.: µPB.uPC.: µPC.Ne les remplacer que par une pièce All resistors are in ohms. uPD.: µPD.portant le numéro spécifié. METAL: Metal-film resistor. • CAPACITORS METAL OXIDE: Metal oxide-film resistor. uF: µF When indicating parts by reference F: nonflammable • COILS number, please include the board. uH: µH • Abbreviation AUS : Australian model J : Japanese model CN : Chinese model JE : Tourist model CND : Canadian model KR : Korea model HK : Hong Kong model Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-435-A CD-262 (30) BOARD, COMPLETE (S30) A-7074-429-A CD-262 (50) BOARD, COMPLETE (S50) < RESISTOR > *************************** (Ref.No.: 2,000 Series) R301 1-218-937-11 RES-CHIP 47 5% 1/16W (IC301 is not included in this complete board) R302 1-218-935-11 RES-CHIP 33 5% 1/16W (S30) < CAPACITOR > R302 1-218-931-11 RES-CHIP 15 5% 1/16W (S50) C301 1-113-985-11 TANTAL. CHIP 10uF 20% 20V R303 1-218-935-11 RES-CHIP 33 5% 1/16W C302 1-119-751-11 TANTAL. CHIP 22uF 20% 16V (S30) C303 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R303 1-218-931-11 RES-CHIP 15 5% 1/16W C304 1-104-329-11 CERAMIC CHIP 0.1uF 10% 50V (S50) C305 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R304 1-218-963-11 RES-CHIP 6.8K 5% 1/16W C306 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V (S30) C307 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R304 1-218-957-11 RES-CHIP 2.2K 5% 1/16W C308 1-107-820-11 CERAMIC CHIP 0.1uF 16V (S50) C309 1-164-850-11 CERAMIC CHIP 10PF 0.50PF 16V R305 1-218-989-11 RES-CHIP 1M 5% 1/16W C311 1-125-827-91 CERAMIC CHIP 1uF 10% 25V (S30) R305 1-218-981-11 RES-CHIP 220K 5% 1/16W C312 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V (S50) R306 1-218-959-11 RES-CHIP 3.3K 5% 1/16W < CONNECTOR > R307 1-218-990-11 SHORT 0 CN301 1-766-348-21 CONNECTOR, FFC/FPC 18P R308 1-218-977-11 RES-CHIP 100K 5% 1/16W R309 1-218-937-11 RES-CHIP 47 5% 1/16W < DIODE > (S30) R309 1-208-643-11 RES-CHIP 22 5% 1/16W D301 8-719-073-01 DIODE MA111- (K8).S0 (S50)

PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP

< FERRITE BEAD > A-7074-434-A DD-141 (30) BOARD, COMPLETE (S30) FB301 1-414-228-11 INDUCTOR CHIP 0uH A-7074-426-A DD-141 (50) BOARD, COMPLETE (S50) **************************** < IC > (Ref.No.: 1,000 Series) IC301 A-7031-090-A CCD BLOCK ASSY (CCD IMAGER) (S30) < CAPACITOR > IC301 A-7031-092-A CCD BLOCK ASSY (CCD IMAGER) (S50) C001 1-164-880-11 CERAMIC CHIP 180PF 5% 16V < COIL > C002 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C003 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V L301 1-414-757-11 INDUCTOR 100uH C004 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V C005 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V < TRANSISTOR > C007 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V Q301 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C008 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V Q302 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1 C009 1-104-913-11 TANTAL. CHIP 10uF 20% 16V C010 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V (Note) Be sure to read “Precautions for Replcement of CCD Imager” on page 4-8 when changing the CCD imager 6-5,

DD-141

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C013 1-104-913-11 TANTAL. CHIP 10uF 20% 16V < CONNECTOR > C014 1-164-941-11 CERAMIC CHIP 0.0047uF 10% 16V C015 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V CN001 1-785-283-21 PIN, CONNECTOR (PC BOARD) 14P C016 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V CN851 1-766-346-21 CONNECTOR, FFC/FPC 16P C017 1-164-935-11 CERAMIC CHIP 470PF 10% 16V CN852 1-794-044-21 CONNECTOR, BOARD TO BOARD 80P C018 1-164-935-11 CERAMIC CHIP 470PF 10% 16V < DIODE > C019 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C020 1-104-913-11 TANTAL. CHIP 10uF 20% 16V D001 8-719-027-76 DIODE 1SS357-TPH3 C021 1-164-935-11 CERAMIC CHIP 470PF 10% 16V D002 8-719-027-77 DIODE MA796-TX C022 1-164-935-11 CERAMIC CHIP 470PF 10% 16V D003 8-719-073-01 DIODE MA111- (K8).S0 C023 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V D004 8-719-073-01 DIODE MA111- (K8).S0 D801 8-719-420-14 DIODE MA8082-M (TX) C024 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C025 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V < FERRITE BEAD > C026 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V C027 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V FB851 1-414-228-11 INDUCTOR CHIP 0uH C028 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V < IC > C029 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C030 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V IC001 8-759-060-94 IC MB3785APFV-G-BND-ER C031 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V IC802 8-759-652-45 IC NJM2568V (TE2) C032 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V IC851 8-759-657-69 IC PDIUSBP11APW, 118 C033 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V < COIL > C034 1-164-506-11 CERAMIC CHIP 4.7uF 16V C035 1-104-847-11 TANTAL. CHIP 22uF 20% 4V L001 1-419-353-21 INDUCTOR 10uH C036 1-113-682-11 TANTAL. CHIP 33uF 20% 10V L002 1-419-353-21 INDUCTOR 10uH C037 1-164-506-11 CERAMIC CHIP 4.7uF 16V L003 1-416-345-11 INDUCTOR 22uH C038 1-117-919-11 TANTAL. CHIP 10uF 20% 6.3V L004 1-416-345-11 INDUCTOR 22uH L005 1-412-939-11 INDUCTOR 1uH C039 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C042 1-125-838-91 CERAMIC CHIP 2.2uF 10% 6.3V L006 1-419-354-21 INDUCTOR 22uH C043 1-164-506-11 CERAMIC CHIP 4.7uF 16V L008 1-412-939-11 INDUCTOR 1uH C044 1-135-214-21 TANTAL. CHIP 4.7uF 20% 20V L009 1-469-524-91 INDUCTOR 4.7uH C046 1-107-819-11 CERAMIC CHIP 0.022uF 10% 16V L010 1-412-939-11 INDUCTOR 1uH L011 1-412-939-11 INDUCTOR 1uH C047 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C048 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V L012 1-412-939-11 INDUCTOR 1uH C049 1-165-319-11 CERAMIC CHIP 0.1uF 50V L013 1-414-406-11 INDUCTOR 220uH C050 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V L014 1-412-947-11 INDUCTOR 4.7uH C051 1-165-319-11 CERAMIC CHIP 0.1uF 50V L801 1-414-756-11 INDUCTOR 47uH L802 1-414-754-11 INDUCTOR 10uH C052 1-135-177-21 TANTALUM CHIP 1uF 20% 20V C053 1-164-505-11 CERAMIC CHIP 2.2uF 16V < TRANSISTOR > C054 1-104-913-11 TANTAL. CHIP 10uF 20% 16V C055 1-164-346-11 CERAMIC CHIP 1uF 16V Q001 8-729-804-41 TRANSISTOR 2SB1122-ST-TD C803 1-113-682-11 TANTAL. CHIP 33uF 20% 10V Q002 8-729-047-74 TRANSISTOR CPH5701-TL Q003 8-729-047-74 TRANSISTOR CPH5701-TL C806 1-107-820-11 CERAMIC CHIP 0.1uF 16V Q004 8-729-033-14 TRANSISTOR FP107-TL C808 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q005 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO C809 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C811 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V Q006 8-729-804-41 TRANSISTOR 2SB1122-ST-TD C812 1-107-820-11 CERAMIC CHIP 0.1uF 16V Q007 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO Q008 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO C813 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q009 8-729-804-41 TRANSISTOR 2SB1122-ST-TD C814 1-164-156-11 CERAMIC CHIP 0.1uF 25V Q010 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C815 1-164-156-11 CERAMIC CHIP 0.1uF 25V C816 1-104-851-11 TANTAL. CHIP 10uF 20% 10V Q013 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO C817 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V Q014 8-729-037-74 TRANSISTOR UN9213J- (K8).SO Q016 8-729-041-23 TRANSISTOR NDS356AP C818 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V Q017 8-729-037-61 TRANSISTOR UN9113J- (K8).SO C819 1-127-569-91 TANTAL. CHIP 100uF 20% 4V Q018 8-729-037-74 TRANSISTOR UN9213J- (K8).SO C820 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V C851 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q019 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO C852 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V Q020 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO Q021 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO C853 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V Q022 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO C854 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q023 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO C855 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C856 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q024 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO 6-6,

DD-141

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q025 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO R042 1-218-955-11 RES-CHIP 1.5K 5% 1/16W Q026 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO Q027 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO R043 1-218-955-11 RES-CHIP 1.5K 5% 1/16W Q028 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO R044 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R045 1-208-707-11 METAL CHIP 10K 0.5% 1/16W Q029 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO R046 1-218-937-11 RES-CHIP 47 5% 1/16W Q030 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO R047 1-218-973-11 RES-CHIP 47K 5% 1/16W Q031 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO Q032 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO R048 1-208-715-11 METAL CHIP 22K 0.5% 1/16W Q033 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO R049 1-218-973-11 RES-CHIP 47K 5% 1/16W R050 1-218-965-11 RES-CHIP 10K 5% 1/16W Q801 8-729-037-74 TRANSISTOR UN9213J- (K8).SO R051 1-218-849-11 METAL CHIP 3.3K 0.5% 1/16W Q802 8-729-037-61 TRANSISTOR UN9113J- (K8).SO R052 1-218-977-11 RES-CHIP 100K 5% 1/16W Q805 8-729-037-92 TRANSISTOR 2SD2216J-R (TX).SO Q806 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO R053 1-218-977-11 RES-CHIP 100K 5% 1/16W Q807 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO R054 1-218-977-11 RES-CHIP 100K 5% 1/16W R055 1-218-965-11 RES-CHIP 10K 5% 1/16W Q851 8-729-037-61 TRANSISTOR UN9113J- (K8).SO R056 1-218-967-11 RES-CHIP 15K 5% 1/16W Q852 8-729-042-74 TRANSISTOR UN9216J- (K8).SO R057 1-208-719-11 METAL CHIP 33K 0.5% 1/16W Q853 8-729-037-61 TRANSISTOR UN9113J- (K8).SO R058 1-218-978-11 METAL CHIP 120K 0.5% 1/16W < RESISTOR > R059 1-218-990-11 SHORT 0 R060 1-218-978-11 METAL CHIP 120K 0.5% 1/16W R001 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R061 1-218-977-11 RES-CHIP 100K 5% 1/16W R002 1-216-864-11 METAL CHIP 0 5% 1/16W R062 1-218-977-11 RES-CHIP 100K 5% 1/16W R004 1-218-982-11 RES-CHIP 270K 5% 1/16W R005 1-208-711-11 METAL CHIP 15K 0.5% 1/16W R063 1-218-977-11 RES-CHIP 100K 5% 1/16W R006 1-218-878-11 METAL CHIP 20K 0.5% 1/16W R064 1-218-973-11 RES-CHIP 47K 5% 1/16W R065 1-208-933-11 METAL CHIP 82K 0.5% 1/16W R007 1-208-696-11 METAL CHIP 3.6K 0.5% 1/16W R066 1-218-977-11 RES-CHIP 100K 5% 1/16W R008 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R067 1-218-973-11 RES-CHIP 47K 5% 1/16W R009 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W R010 1-218-972-11 RES-CHIP 39K 5% 1/16W R068 1-218-977-11 RES-CHIP 100K 5% 1/16W R011 1-218-970-11 RES-CHIP 27K 5% 1/16W R069 1-218-965-11 RES-CHIP 10K 5% 1/16W R070 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R012 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R071 1-208-922-11 METAL CHIP 30K 0.5% 1/16W R013 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R072 1-208-715-11 METAL CHIP 22K 0.5% 1/16W R014 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R015 1-218-948-11 METAL CHIP 390 0.5% 1/16W R073 1-208-931-11 METAL CHIP 68K 0.5% 1/16W R016 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R074 1-208-713-11 METAL CHIP 18K 0.5% 1/16W R075 1-208-688-11 METAL CHIP 1.6K 0.5% 1/16W R017 1-218-979-11 RES-CHIP 150K 5% 1/16W R076 1-218-978-11 METAL CHIP 120K 0.5% 1/16W R018 1-208-707-11 METAL CHIP 10K 0.5% 1/16W R078 1-216-864-11 METAL CHIP 0 5% 1/16W R019 1-208-703-11 METAL CHIP 6.8K 0.5% 1/16W R020 1-208-691-11 METAL CHIP 2.2K 0.5% 1/16W R081 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R021 1-208-713-11 METAL CHIP 18K 0.5% 1/16W R801 1-218-990-11 SHORT 0 R803 1-218-977-11 RES-CHIP 100K 5% 1/16W R022 1-218-973-11 RES-CHIP 47K 5% 1/16W R804 1-218-965-11 RES-CHIP 10K 5% 1/16W R023 1-208-931-11 METAL CHIP 68K 0.5% 1/16W R805 1-218-965-11 RES-CHIP 10K 5% 1/16W R024 1-218-961-11 RES-CHIP 4.7K 5% 1/16W R025 1-218-953-11 RES-CHIP 1K 5% 1/16W R806 1-218-949-11 RES-CHIP 470 5% 1/16W R026 1-218-960-11 RES-CHIP 3.9K 5% 1/16W R807 1-218-989-11 RES-CHIP 1M 5% 1/16W R808 1-218-973-11 RES-CHIP 47K 5% 1/16W R027 1-218-958-11 METAL CHIP 2.7K 0.5% 1/16W R809 1-218-965-11 RES-CHIP 10K 5% 1/16W R028 1-208-711-11 METAL CHIP 15K 0.5% 1/16W R810 1-218-939-11 RES-CHIP 68 5% 1/16W R029 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W R030 1-218-990-11 SHORT 0 R811 1-218-969-11 RES-CHIP 22K 5% 1/16W R031 1-218-990-11 SHORT 0 R812 1-218-973-11 RES-CHIP 47K 5% 1/16W R853 1-218-955-11 RES-CHIP 1.5K 5% 1/16W R032 1-218-965-11 RES-CHIP 10K 5% 1/16W R854 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R033 1-218-990-11 SHORT 0 R855 1-218-977-11 RES-CHIP 100K 5% 1/16W R034 1-218-990-11 SHORT 0 R035 1-218-949-11 RES-CHIP 470 5% 1/16W R856 1-220-168-11 RES-CHIP 24 5% 1/16W R036 1-218-951-11 RES-CHIP 680 5% 1/16W R857 1-220-168-11 RES-CHIP 24 5% 1/16W R037 1-218-949-11 RES-CHIP 470 5% 1/16W < TRANSFORMER > R038 1-218-949-11 RES-CHIP 470 5% 1/16W R039 1-208-709-11 METAL CHIP 12K 0.5% 1/16W 0T001 1-429-565-21 TRANSFORMER, CONVERTER R040 1-208-721-11 METAL CHIP 39K 0.5% 1/16W PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-7 ber specified. portant le numéro spécifié.,

JK-194 KJ-11 MS-50 PD-127

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7074-428-A JK-194 BOARD, COMPLETE CN003 1-766-344-21 CONNECTOR, FFC/FPC 14P *********************** CN004 1-793-111-14 CONNECTOR, MEMORY STICK (Ref.No.: 2,000 Series) CN005 1-785-283-21 PIN, CONNECTOR (PC BOARD) 14P < CAPACITOR > < DIODE > C201 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V D001 8-719-073-03 DIODE MA8082- (K8).S0 C202 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V D002 8-719-066-44 DIODE CL-270HR-C-TS D003 8-719-073-03 DIODE MA8082- (K8).S0 < CONNECTOR > D005 8-719-158-49 DIODE MA8120-TX D006 8-719-027-76 DIODE 1SS357-TPH3 CN201 1-766-346-21 CONNECTOR, FFC/FPC 16P CN202 1-794-335-11 CONNECTOR (USB) (4P), SQUARE < FUSE > < DIODE > 0F001 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) 0F002 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) D201 8-719-045-87 DIODE MA4Z082WA- (TX).SO 0F003 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) D203 8-719-045-87 DIODE MA4Z082WA- (TX).SO 0F004 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) D205 8-719-073-01 DIODE MA111- (K8).S0 0F005 1-576-406-11 FUSE, MICRO (1608) (1.4A/32V) D206 8-719-073-01 DIODE MA111- (K8).S0 D207 8-719-045-87 DIODE MA4Z082WA- (TX).SO < FERRITE BEAD > D209 8-719-045-87 DIODE MA4Z082WA- (TX).SO FB001 1-414-228-11 INDUCTOR CHIP 0uH D210 8-719-159-96 DIODE RD5.1UM-T1B FB002 1-414-228-11 INDUCTOR CHIP 0uH D211 8-719-159-96 DIODE RD5.1UM-T1B < LINE FILTER > < JACK > LF001 1-411-957-11 FILTER, COMMON MODE J201 1-695-514-31 JACK (SMALL TYPE) 1P (VIDEO OUT) (S30) J201 1-695-514-31 JACK (SMALL TYPE) 1P (A/V OUT) (S50) < TRANSISTOR > < LINE FILTER > Q001 8-729-047-68 TRANSISTOR SSM3K03FE (TPL3) Q002 8-729-046-77 TRANSISTOR SI4963DY-T1 LF201 1-419-100-21 COIL, COMMON-MODE CHOKE Q003 8-729-804-41 TRANSISTOR 2SB1122-ST-TD LF203 1-419-100-21 COIL, COMMON-MODE CHOKE Q004 8-729-037-74 TRANSISTOR UN9213J- (K8).SO LF204 1-419-100-21 COIL, COMMON-MODE CHOKE < RESISTOR > < RESISTOR > R001 1-216-821-11 METAL CHIP 1K 5% 1/16W R201 1-216-851-11 METAL CHIP 330K 5% 1/16W R002 1-216-821-11 METAL CHIP 1K 5% 1/16W R202 1-216-821-11 METAL CHIP 1K 5% 1/16W R003 1-216-853-11 METAL CHIP 470K 5% 1/16W R212 1-216-849-11 METAL CHIP 220K 5% 1/16W R004 1-216-857-11 METAL CHIP 1M 5% 1/16W R213 1-216-864-11 METAL CHIP 0 5% 1/16W R005 1-216-150-91 RES-CHIP 10 5% 1/8W

PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP

R006 1-216-821-11 METAL CHIP 1K 5% 1/16W A-7074-432-A KJ-11 BOARD, COMPLETE R007 1-216-831-11 METAL CHIP 6.8K 5% 1/16W ********************** R009 1-216-864-11 METAL CHIP 0 5% 1/16W (Ref.No.: 3,000 Series) PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP < SWITCH > A-7074-436-A PD-127 (30) BOARD, COMPLETE (S30) A-7074-430-A PD-127 (50) BOARD, COMPLETE (S50) S301 1-771-483-21 SWITCH, PUSH (1 KEY) (PANEL REVERSE) **************************** PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP (Ref.No.: 2,000 Series) A-7074-425-A MS-50 BOARD, COMPLETE < CAPACITOR > ********************** (Ref.No.: 2,000 Series) C801 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C802 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CAPACITOR > C803 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C804 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C003 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C805 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V C004 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C006 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V C806 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C007 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C807 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V C808 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < CONNECTOR > C810 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V C811 1-104-851-11 TANTAL. CHIP 10uF 20% 10V * CN001 1-580-056-21 PIN, CONNECTOR (SMD) 3P * CN002 1-580-056-21 PIN, CONNECTOR (SMD) 3P C812 1-104-851-11 TANTAL. CHIP 10uF 20% 10V The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-8 ber specified. portant le numéro spécifié.,

PD-127 SW-339

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C813 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V Q904 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO C814 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V C815 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V < RESISTOR > C816 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V R803 1-218-990-11 SHORT 0 C817 1-119-751-11 TANTAL. CHIP 22uF 20% 16V R805 1-218-990-11 SHORT 0 C818 1-119-751-11 TANTAL. CHIP 22uF 20% 16V R808 1-218-969-11 RES-CHIP 22K 5% 1/16W C819 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V R809 1-218-966-11 RES-CHIP 12K 5% 1/16W C902 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V R810 1-218-990-11 SHORT 0 C903 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R812 1-218-973-11 RES-CHIP 47K 5% 1/16W C904 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R813 1-218-967-11 RES-CHIP 15K 5% 1/16W C905 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R814 1-218-971-11 RES-CHIP 33K 5% 1/16W C906 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R817 1-218-966-11 RES-CHIP 12K 5% 1/16W C907 1-164-937-11 CERAMIC CHIP 0.001uF 10% 16V R818 1-218-972-11 RES-CHIP 39K 5% 1/16W C908 1-164-872-11 CERAMIC CHIP 82PF 5% 16V R820 1-218-977-11 RES-CHIP 100K 5% 1/16W C909 1-107-826-91 CERAMIC CHIP 0.1uF 10% 16V R821 1-218-965-11 RES-CHIP 10K 5% 1/16W C911 1-164-739-11 CERAMIC CHIP 560PF 5% 50V R904 1-218-973-11 RES-CHIP 47K 5% 1/16W C912 1-164-872-11 CERAMIC CHIP 82PF 5% 16V R905 1-218-973-11 RES-CHIP 47K 5% 1/16W C913 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R908 1-218-987-11 RES-CHIP 680K 5% 1/16W C914 1-113-994-11 TANTAL. CHIP 6.8uF 20% 16V R909 1-218-978-11 RES-CHIP 120K 5% 1/16W C915 1-164-943-11 CERAMIC CHIP 0.01uF 10% 16V R910 1-218-977-11 RES-CHIP 100K 5% 1/16W C916 1-107-689-21 TANTAL. CHIP 1uF 20% 35V R911 1-218-965-11 RES-CHIP 10K 5% 1/16W C917 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R912 1-218-989-11 RES-CHIP 1M 5% 1/16W C918 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R913 1-218-990-11 SHORT 0 < CONNECTOR > R914 1-218-989-11 RES-CHIP 1M 5% 1/16W R915 1-218-969-11 RES-CHIP 22K 5% 1/16W CN801 1-779-064-11 PIN, CONNECTOR (PC BOARD) 12P R916 1-218-975-11 RES-CHIP 68K 5% 1/16W CN802 1-785-283-21 PIN, CONNECTOR (PC BOARD) 14P R917 1-218-975-11 RES-CHIP 68K 5% 1/16W * CN901 1-774-261-11 CONNECTOR, FFC (ZIF) 24P R918 1-218-973-11 RES-CHIP 47K 5% 1/16W < DIODE > R919 1-218-891-11 METAL CHIP 68K 0.5% 1/16W R920 1-218-883-11 METAL CHIP 33K 0.5% 1/16W D801 8-719-073-01 DIODE MA111- (K8).S0 R921 1-218-961-11 RES-CHIP 4.7K 5% 1/16W D902 8-713-102-80 DIODE 1T369-01-T8A R922 1-218-961-11 RES-CHIP 4.7K 5% 1/16W D903 8-719-976-96 DIODE MA8047-H-TX R925 1-218-977-11 RES-CHIP 100K 5% 1/16W < FERRITE BEAD > R926 1-218-971-11 RES-CHIP 33K 5% 1/16W R928 1-218-977-11 RES-CHIP 100K 5% 1/16W FB801 1-414-234-22 INDUCTOR CHIP 0uH R929 1-218-977-11 RES-CHIP 100K 5% 1/16W FB802 1-414-234-22 INDUCTOR CHIP 0uH R932 1-218-977-11 RES-CHIP 100K 5% 1/16W FB803 1-414-234-22 INDUCTOR CHIP 0uH R933 1-218-971-11 RES-CHIP 33K 5% 1/16W < IC > R934 1-218-990-11 SHORT 0 R935 1-218-883-11 METAL CHIP 33K 0.5% 1/16W IC801 8-759-364-05 IC MB40D001PFV-G-BND-ER R936 1-218-879-11 METAL CHIP 22K 0.5% 1/16W IC802 8-759-539-27 IC IR3Y37A4 R937 1-218-883-11 METAL CHIP 33K 0.5% 1/16W IC901 8-759-587-61 IC LZ9GH234 R938 1-218-879-11 METAL CHIP 22K 0.5% 1/16W IC902 8-759-327-01 IC NJM062V (TE2) R960 1-218-937-11 RES-CHIP 47 5% 1/16W < COIL > R961 1-218-937-11 RES-CHIP 47 5% 1/16W R962 1-218-937-11 RES-CHIP 47 5% 1/16W L801 1-414-757-11 INDUCTOR 100uH PPPPPPPPPPPPPPPPPPPPPPPPPPPPPPPP L802 1-414-078-11 INDUCTOR 10uH L803 1-412-947-11 INDUCTOR 4.7uH A-7074-431-A SW-339 BOARD, COMPLETE L901 1-414-754-11 INDUCTOR 10uH ************************ L902 1-414-754-11 INDUCTOR 10uH (Ref.No.: 2,000 Series) L903 1-412-951-11 INDUCTOR 10uH < BATTERY > L905 1-412-949-21 INDUCTOR 6.8uH 0BT101 1-528-900-11 BATTERY, LITHIUM SECONDARY < TRANSISTOR > < CAPACITOR > Q901 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO Q902 8-729-037-53 TRANSISTOR 2SB1462J-QR (K8).SO C101 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V Q903 8-729-037-52 TRANSISTOR 2SD2216J-QR (K8).SO The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-9 ber specified. portant le numéro spécifié.,

SW-339

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < CONNECTOR > BT901 1-694-654-11 TERMINAL BOARD, BATTERY BZ901 1-529-739-11 BUZZER, PIEZOELECTRIC (S30) CN101 1-573-347-11 CONNECTOR, FFC/FPC (ZIF) 7P IC301 A-7031-090-A CCD BLOCK ASSY (CCD IMAGER) (S30) IC301 A-7031-092-A CCD BLOCK ASSY (CCD IMAGER) (S50) < DIODE > LCD901 1-803-857-21 INDICATOR MODULE LIQUID CRYSTAL D101 8-719-073-01 DIODE MA111- (K8).S0 MIC901 1-542-428-11 MICROPHONE UNIT (S50) D102 8-719-060-92 DIODE SML-311YTT86 (FLASH) 0ND901 1-517-878-31 TUBE, FLUORESCENT, COLD CATHODE D103 8-719-057-91 DIODE RD8.2UM-T1B SP901 1-505-862-41 SPEAKER (2.0 cm) (S50) D104 8-719-045-87 DIODE MA4Z082WA- (TX).SO < RESISTOR > ACCESSORIES & PACKING MATERIALS ******************************** R101 1-216-817-11 METAL CHIP 470 5% 1/16W R102 1-216-824-11 METAL CHIP 1.8K 5% 1/16W 0 1-475-599-11 ADAPTOR, AC (EXCEPT KR) R103 1-216-824-11 METAL CHIP 1.8K 5% 1/16W 0 1-475-599-71 ADAPTOR, AC (KR) R104 1-216-835-11 METAL CHIP 15K 5% 1/16W 0 1-569-007-11 ADAPTOR, CONVERSION 2P (E, JE) R106 1-216-826-11 METAL CHIP 2.7K 5% 1/16W 0 1-569-008-21 ADAPTOR, CONVERSION 2P (E) 0 1-696-819-11 CORD, POWER (AUS) R107 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R109 1-216-829-11 METAL CHIP 4.7K 5% 1/16W 0 1-769-608-11 CORD, POWER (AEP, E) R111 1-216-829-11 METAL CHIP 4.7K 5% 1/16W 0 1-776-985-11 CORD, POWER (KR) R112 1-216-831-11 METAL CHIP 6.8K 5% 1/16W 0 1-783-374-11 CORD, POWER (UK, HK) R113 1-216-839-11 METAL CHIP 33K 5% 1/16W 1-783-738-31 CORD, CONNECTION (AV CONNECTING 1.5m) (S50) R114 1-216-831-11 METAL CHIP 6.8K 5% 1/16W 0 1-790-073-11 CORD, POWER 2P (JE, J) R115 1-216-839-11 METAL CHIP 33K 5% 1/16W R116 1-216-839-11 METAL CHIP 33K 5% 1/16W 0 1-790-107-22 CORD, POWER (US, CND) 1-791-785-11 CORD, CONNECTION (USB CABLE) < SWITCH > 1-792-955-11 CORD, CONNECTION (VIDEO CONNECTING 1.5m) (S30) S101 1-771-688-21 SWITCH, TACTILE (CONTROL) 3-056-776-01 STRAP, LIST S102 1-771-138-61 SWITCH, KEY BOARD (DISPLAY) 3-060-523-01 MANUAL, INSTRUCTION (JAPANESE) (J) S103 1-771-138-61 SWITCH, KEY BOARD (FLASH) S104 1-771-138-61 SWITCH, KEY BOARD (PROGRAM AE) 3-060-523-11 MANUAL, INSTRUCTION (ENGLISH) S105 1-771-138-61 SWITCH, KEY BOARD (US,CND,AEP,UK,E,HK,AUS,JE) (PROGRAM AE/VOLUME +) 3-060-523-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) (CND, AEP, JE) S106 1-572-467-21 SWITCH, PUSH (1 KEY) (PANEL UP/DOWN) 3-060-523-31 MANUAL, INSTRUCTION (SPANISH, S107 1-771-138-61 SWITCH, KEY BOARD (FOCUS) PORTUGUESE) (AEP, E, JE) S108 1-771-138-61 SWITCH, KEY BOARD 3-060-523-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (PROGRAM AE/VOLUME -) (AEP) S109 1-570-397-11 SWITCH, SLIDE (BACK LIGHT) 3-060-523-51 MANUAL, INSTRUCTION (CHINESE) S110 1-572-467-21 SWITCH, PUSH (1 KEY) (PANEL ON/OFF) (E, HK, JE) 3-060-523-61 MANUAL, INSTRUCTION MISCELLANEOUS (RUSSIAN, SWEDISH) (AEP, JE) ************** 3-060-523-71 MANUAL, INSTRUCTION (ARABIC) (E) 3-060-523-81 MANUAL, INSTRUCTION (KOREAN) (JE, KR) 14 1-476-038-11 SWITCH BLOCK, CONTROL (MODE SW) 3-060-716-01 SOFT(2000), BUNDLE 015 1-476-005-11 FLASH UNIT 3-061-217-01 STRING, CAP 57 1-677-877-11 FP-024 FLEXIBLE BOARD 59 1-476-039-11 SWITCH BLOCK, CONTROL 3-866-482-01 MANUAL, INSTRUCTION (for SAFETY) (ZOOM/POWER SW) (JAPANESE) (J) 060 1-794-045-11 CONNECTOR, DC-IN X-3950-660-2 CAP ASSY, LENS 61 1-678-002-11 FP-025 FLEXIBLE BOARD 64 1-678-003-11 FP-026 FLEXIBLE BOARD 68 1-960-457-11 HARNESS (YP-052) 104 1-960-474-11 HARNESS (SK-100) 0112 1-418-879-21 TRANSFORMER UNIT, INVERTER 120 1-960-472-11 HARNESS (YP-053) 121 1-960-473-11 HARNESS (YP-054) 151 1-758-415-11 LENS, ZOOM (VCL-6103WA) 157 1-678-001-11 FP-023 FLEXIBLE BOARD 161 1-758-435-11 FILTER BLOCK, OPTICAL (S30) 161 1-758-436-11 FILTER BLOCK, OPTICAL (S50) The components identified by Les composants identifiés par une (Note) Be sure to read “Precautions for Replcement of mark 0 or dotted line with marque 0 sont critiques pour lamark 0 are critical for safety. sécurité. CCD Imager” on page 4-8 when changing Replace only with part num- Ne les remplacer que par une pièce the CCD imager 6-10 ber specified. portant le numéro spécifié., FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC mode R-Y

MG R YE

B-Y

B

G CY ✄ DSC-S30/S50 For PAL mode R-Y

MG R YE

B-Y

B

G CY Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear DSC-S30/S50 sheet for use. – 117 – ✄,

DSC-S30/S50 Sony Corporation

2000D0549-1 9-929-819-31 Personal VIDEO Products Company Printed in Japan © 2000. 4 – 118 – Published by Safety & Service Engineering Dept.,

DSC-S30/S50

US Model Canadian Model

SERVICE MANUAL AEP ModelUK Model

Level2EModel Hong Kong Model 2000. 09 Australian Model Chinese Model Korea Model Tourist Model Japanese Model

SUPPLEMENT-1

File this supplement with the service manual. (PV00-007) • Correction of Hall Adjustment • Supplied Parts Modification,

DSC-S30/S50 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

& : Points added portion. JK-194 (USB, A/V OUT), KJ-11 (PANEL REVERSE), SW-339 (SWITCH) PRINTED WIRING BOARDS – Ref. No.: JK-194 board; 2,000 series, KJ-11 board; 3,000 series, SW-339 board; 2,000 series – (Service manual pages 4-37 and 4-38) BT101 ( BATTERY, *LITHIUM SECONDARY (

SECTION 5 ADJUSTMENTS

- : Points changed portion. 1-4. CAMERA SYSTEM ADJUSTMENTS 1. HALL Adjustment (Service manual page 5-13) INCORRECT CORRECT ; Note 2: The right four digits of the page: 1 displayed data of the Note 2: The right two digits of the page: 1 displayed data of the adjusting remote commander. adjusting remote commander. 1:XX:XX - 1:00:XX Displayed data Displayed data – 2 –,

DSC-S30/S50 SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS & : Points added portion. NOTE: - : Points changed portion. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay 6-1-1. FRONT PANEL SECTION should be anticipated when ordering these items. (Service manual page 6-1) Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3950-656-1 CABINET (FRONT) ASSY (S50) 1 X-3950-656-3 CABINET (FRONT) ASSY (S50) [ 1 X-3950-664-1 CABINET (FRONT) ASSY (S30) 1 X-3950-664-3 CABINET (FRONT) ASSY (S30) [ 10 X-3950-659-1 CABINET (UPPER) ASSY (S50) 10 X-3950-659-4 CABINET (UPPER) ASSY (S50) [ 10 X-3950-665-1 CABINET (UPPER) ASSY (S30) 10 X-3950-665-4 CABINET (UPPER) ASSY (S30) [ 6-1-2. MAIN SECTION (Service manual page 6-2)

A

52 70 52 BT901 58 52 57 55 $+ A 64 52 52 52 56 65 not supplied 68 Lens block assembly 66 (See page 6-4) 51 ! : BT101 (BATTERY, LITHIUM SECONDARY) ] Board on the mount position. (See page 4-38.)& 71 67not supplied ) Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 X-3950-655-1 HOLDER ASSY, BT 51 X-3950-655-3 HOLDER ASSY, BT [ * 71 3-062-855-01 TAPE (40) ) – 3 –,

DSC-S30/S50

6-1-3. REAR CABINET SECTION (Service manual page 6-3) -109 113 115 119 A not 110 115 supplied 110 [ 120 108 122 107 108 123 106 124

A

126 125 104 135 103 129 not supplied 102 134 108 128 Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 109 X-3950-658-1 CABINET (REAR) ASSY (S50) 109 X-3950-658-3 CABINET (REAR) ASSY (S50) [ 109 X-3950-794-1 CABINET (REAR) ASSY (S30) 109 X-3950-794-3 CABINET (REAR) ASSY (S30) [ * 133 3-062-736-01 SHEET, ELECTROSTATIC Not Supplied [

Sony Corporation

2000I0535-1 9-929-819-82 Personal VIDEO Products Company Printed in Japan © 2000. 9 – 4 – Published by Safety & Service Engineering Dept.]
15

Similar documents

! : Points deleted portion.
DSC-S40 Auto-ADJ SERVICE MANUAL Ver 1.1 2005.11 CORRECTION-1 We will inform you that there are printing errors in the service manual previously issued. • Correction of the Before starting adjustment • Correction of the Table 6-1-1 • Correction of the Service tool DSC-S40 2005K0500-1© 2005.11 9-876-8
& : Points added portion.
DSC-S40 LEVEL 2 US Model SERVICE MANUAL Canadian Model AEP Model Ver 1.2 2005.09 UK Model E Model Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model SUPPLEMENT-1 Tourist Model File this supplement with the service manual. (PV05-041) • Change of Repair Parts Suffix No. of ST-11
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2005.06 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
TABLE OF CONTENTS
DSC-S30/S50 SERVICE MANUAL US Model Canadian Model Level 3 Ver 1.1 2000. 09 With SUPPLEMENT 1 AEP Model (9-929-819-83) UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Photo: DSC-S30 Japanese Model This service manual contains information for Japanese model a
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS Camera [Power, general]
DSC-S40 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2005.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Korea Model Japanese Model Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
SPECIFICATIONS [System] USB communication
DSC-S45 SERVICE MANUAL US Model Ver 1.0 2006.03 Revision History How to use Acrobat Reader Internal memory ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont cr
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.2 2006.09 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
SPECIFICATIONS [System] [LCD screen]
DSC-S500 SERVICE MANUAL US Model Ver 1.1 2006.07 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Korea Model ON BOARD Link SPECIFICATIONS DISASSEMBLY REPAIR PARTS LIST SERVICE NOTE BLOCK DIAGRAMS The components ide
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS
SAFETY CHECK-OUT
DSC-S600 SERVICE MANUAL LEVEL 3 US Model Ver. 1.1 2006. 07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Chinese Model Internal memory Brazilian Model ON BOARD Hong Kong Model Korea Model Link SERVICE NOTE SCHEMATIC DIAGRAMS REPAIR PARTS LIST F
These specifications are extracted from instruction
DSC-S600 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2005. 12 Canadian Model Revision History AEP Model UK Model E Model Australian Model Chinese Model Brazilian Model Hong Kong Model Korea Model Link SPECIFICATIONS ACCESSORIES SELF-DIAGNOSIS FUNCTION INSTRUCTION MANUAL Note : Note : The components iden
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 1 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/Silver Argentine Model Lin
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.0 2005.03 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
SPECIFICATIONS Camera [Power, general] Cyber-shot Station CSS-SA
DSC-S60/S80/S90/ST80 SERVICE MANUAL LEVEL 2 DSC-S60/S90 Ver 1.1 2005.07 US Model Canadian Model Revision History Chinese Model Tourist Model DSC-S60/S80/S90/ How to use Acrobat Reader ST80 AEP Model UK Model E Model Hong Kong Model DSC-S60/S80/S90 Australian Model Korea Model DSC-S90 Photo: DSC-S90/
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.2 2001.07 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service
SAFETY-RELATED COMPONENT WARNING!!
DSC-S75 SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.2 2001. 11 SPECIFICATIONS System Flash General AC-L10A/B/C Accessories Image device Recommended recording Used battery pack AC power adaptor A/V connecting cable (1) 8.93 mm (1/1.8 type) color distance (ISO is set to AUTO): NP-FM50 Power requir
Supplied accessories
DSC-S70 SERVICE MANUAL US Model Canadian Model Level 2 Ver. 1.3 2002.09 AEP Model UK Model E model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-58 board SY-58 board This service
SPECIFICATIONS System Output connector General AC-L10A/B/C NP-FM50 battery pack
DSC-S85 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Differences Manual This Service Manual covers only differences from DSC-S75 (Level 2). In performing repair, refe
SPECIFICATIONS System Output connector General AC-L10A/B/C NP-FM50 battery pack
DSC-S85 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Differences Manual This Service Manual covers only differences from DSC-S75 (Level 2). In performing repair, refe
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT
DSC-S75 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.2 2001. 08 Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model This service manual contains information for Japanese model as well. On the SY-68 board SY-68 board This service
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2003. 10 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model
DSC-T1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004. 03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE F
DSC-T1 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2004. 03 Canadian Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model
DSC-T1 SERVICE MANUAL LEVEL 1 US Model Ver 1.2 2004. 03 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Korea Model Chinese Model Tourist Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION • INSTRUCTION MANUAL is shown at the end of this docu
• Change of Automatic Adjustment Program • Change of Message for Destination Data
DSC-T100 Auto-ADJ SERVICE MANUAL Ver. 1.1 2007.04 SUPPLEMENT-1 File this supplement with the service manual. (DI07-003) • Change of Automatic Adjustment Program • Change of Message for Destination Data Write • Addition of [Read], [Save], and [Load] buttons to Angular Velocity Sensitivity Adjustment
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-T10 SERVICE MANUAL LEVEL 3 US Model Ver 1.1 2006.09 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Photo: Silver Tourist Model
SPECIFICATIONS Camera [Input and Output connectors] BC-CS3 battery charger
DSC-T10 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.07 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory ON BOARD Korea Model Argentine Model Japanese Model Tourist Model Photo: Silver Link SPECIFICATI
SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-T100 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Brazilian Model Japanese Model Tourist Model Photo: Silver Link SPECIFICA
WARNING To prevent fire or shock hazard, do
DSC-T11 SERVICE MANUAL LEVEL 1 Differences Manual DSC-T11 AEP Model UK Model E Model Ver 1.1 2004. 09 Hong Kong Model Australian Model Revision History Korea Model Chinese Model Tourist Model Japanese Model • This Service Manual shows only the difference from DSC-T1. Refer to the Service Manual Leve