Download: DSC-V1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model

DSC-V1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2003. 05 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987626151.pdf). • For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987626141.pdf). • This service manual contains information for Japanese model as well. • Reference No. search on pri...
Author: 阿由葉 Shared: 8/19/19
Downloads: 283 Views: 4767

Content

DSC-V1 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2003. 05 Canadian Model

Revision History AEP Model

UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (987626151.pdf). • For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (987626141.pdf). • This service manual contains information for Japanese model as well. • Reference No. search on printed wiring boards is available. • Note in Lens Frame Installation • HELP: Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. On the SY-089 and DD-195 boards SY-089 board This service manual procides the information that is premised Schematic diagram ...Pages 4-9 to 4-32 the circuit board replacement service and not intended repair Printed wiring board ...Pages 4-51 to 4-54 inside the SY-089 and DD-195 boards. Electrical parts list ...Pages 5-10 to 5-13 Therefore, schematic diagram, printed wiring board and DD-195 board electrical parts list of the SY-089 and DD-195 boards are not Schematic diagram ...Pages 4-33 to 4-36 shown. Printed wiring board ...Pages 4-55 and 4-56 The following pages are not shown. Electrical parts list ...Pages 5-7 and 5-8 The above-described information is shown in service manual Level 3.

DIGITAL STILL CAMERA

,

COVER TM SPECIFICATIONS

xCamera [General] xNP-FC11 battery pack [System] Used battery pack Used battery Image device NP-FC11 Lithium-ion battery 9.04 mm (1/1.8 type) color CCD Power requirements Maximum voltage Primary color filter 3.6 V DC 4.2 V Total pixels number of camera Power consumption (during shooting with Nominal voltage Approx. 5 255 000 pixels LCD screen on) DC 3.6 V Effective pixels number of camera 1.7 W Capacity 2.8 Wh (780 mAh) Approx. 5 090 000 pixels Operating temperature Lens 4× zoom lens 0°C to 40°C (32°F to 104°F) f = 7.0 – 28.0 mm (34 – 136 mm when Storage temperature xAccessories converted to a 35 mm still camera) –20°C to +60°C (–4°F to +140°F) • AC Adaptor (1) F2.8 – 4.0 Dimensions • Power cord (mains lead) (1) Exposure control 99.5×65.2×56.8 mm Automatic exposure, Shutter speed (4×2 5/8×2 1/4 inches) • USB cable (1) priority, Aperture priority, Manual (W/H/D, excluding maximum • NP-FC11 battery pack (1) exposure, Scene selection (6 modes) protrusions) • A/V connecting cable (1) White balance Mass Approx. 300 g (10.6 oz) (including • Hand strap (1) Automatic, Daylight, Cloudy, battery pack NP-FC11, “Memory • “Memory Stick” (32 MB) (1) Fluorescent, Incandescent, Flash, Stick”, and hand strap) One-push • CD-ROM (USB driver SPVD-010) (1)Built-in microphone File format (DCF compliant) Electret condenser microphone • Operating instructions (1) Still images: Exif Ver. 2.2 JPEG Built-in speaker compliant, GIF (for Clip Motion), Design and specifications are subject to change Dynamic speaker TIFF, DPOF compatible without notice. Audio with still image: MPEG1 Exif Print Compatible compliant (Monaural) PRINT Image Matching II Compatible Movies: MPEG1 compliant (Monaural) Recording media xAC-LS5 AC Adaptor “Memory Stick” Power requirements Flash Recommended distance (ISO set to 100 to 240 V AC, 50/60 Hz Auto): Current consumption 0.4 m to 2.8 m (15 3/4 inches to 0.16 to 0.09 A 110 1/4 inches) (W) Power consumption 0.4 m to 2.0 m (15 3/4 inches to 11 W 78 3/4 inches) (T) Rated output voltage [Input and Output connectors] 4.2 V DC, 1.5 A A/V OUT (MONO) (Monaural) Operating temperature Minijack 0°C to 40°C (32°F to 104°F) Video: 1 Vp-p, 75 Ω, unbalanced, Storage temperature sync negative –20°C to +60°C (–4°F to +140°F) Audio: 327 mV (at a 47 kΩ load) Dimensions (approx.) Output impedance 2.2 kΩ 48×29×81 mm ACC jack Mini-minijack (ø 2.5 mm) (1 15/16×1 3/16×3 1/4 inches) USB jack mini-B (W/H/D) excluding projecting parts Mass (approx.) [LCD screen] 130 g (5 oz) excluding power cord (mains lead) LCD panel 3.8 cm (1.5 type) TFT drive Total number of dots 123 200 (560×220) dots — 2 —,

CAUTION Use of controls or adjustments or performance

procedures other than those specified herein may result in hazardous radiation exposure. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. Flexible Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270˚C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page Section Title Page 1. SERVICE NOTE 5. REPAIR PARTS LIST 1-1. Note for Repair ································································ 1-1 5-1. Exploded Views ······························································· 5-2 1-2. Discharging of the ST-083 Flexible Board’s 5-1-1.Cabinet Section ································································ 5-2 Charging Capacitor (C333) ············································· 1-1 5-1-2.Frame Block Section-1 ···················································· 5-3 1-3. Note in Lens Frame Installation ······································ 1-2 5-1-3.Frame Block Section-2 ···················································· 5-4 1-4. Notes on Handling the Laser Diode 5-1-4.Lens Block Section ·························································· 5-5 [Laser Unit (D333)] ························································· 1-2 5-2. Electrical Parts List ························································· 5-6 1-5. Description on Self-diagnosis Display ···························· 1-3 2. DISASSEMBLY 2-1. Battery Lid ······································································· 2-3 2-2. Cabinet (Rear) Assembly ················································· 2-3 2-3. LCD Module ···································································· 2-4 2-4. Control Switch Block (GL-51470) ·································· 2-4 2-5. Control Switch Block (Mode-51470) ······························ 2-5 2-6. Cabinet (Front) Assembly ··············································· 2-5 2-7. Stroboscope Block ··························································· 2-6 2-8. SY-089 Board ·································································· 2-6 2-9. Memory Stick Connector ················································ 2-7 2-10. Lens Block Assembly ······················································ 2-7 2-11. ST-083 Flexible Board ···················································· 2-8 2-12. Condenser Holder ···························································· 2-9 2-13. CD-441 Flexible Board ················································· 2-10 2-14. DD-195 Board ······························································· 2-10 2-15. JK-254 Flexible Board ·················································· 2-11 2-16. FU-165 Flexible Board ·················································· 2-11 2-17. Circuit Boards Location ················································ 2-12 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-3 3-3. Power Block Diagram (1/2) ············································· 3-5 3-4. Power Block Diagram (2/2) ············································· 3-7 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-5 CD-441 FLEXIBLE (CCD IMAGER) ··························· 4-7 ST-083 FLEXIBLE (FLASH DRIVE, LASER UNIT) ································· 4-37 SW-395 FLEXIBLE (MIC, LENS ADAPTOR SWITCH) ···························· 4-39 JK-254 FLEXIBLE (USB, A/V JACK) ························· 4-39 MS-165 FLEXIBLE (MEMORY STICK CONNECTOR) ····························· 4-40 BB-004 FLEXIBLE (SY-DD EXTENSION BOARD) ·································· 4-41 FU-165 FLEXIBLE (DC IN, BATTERY IN) ··············· 4-43 CONTROL SWITCH BLOCK (GL-51470) ················· 4-44 CONTROL SWITCH BLOCK (MODE-51470) ··········· 4-45 4-3. Printed Wiring Boards ··················································· 4-47 CD-441 FLEXIBLE ······················································ 4-49 ST-083 FLEXIBLE ······················································· 4-57 SW-395 FLEXIBLE ······················································ 4-59 JK-254 FLEXIBLE ······················································· 4-61 MS-165 FLEXIBLE ······················································ 4-61 BB-004 FLEXIBLE ······················································ 4-62 FU-165 FLEXIBLE ······················································· 4-63 4-5. Mounted Parts Location ················································ 4-67 — 4 —, COVER SECTION 1

SERVICE NOTE

1-1. NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector. bent at the terminal. It is possible that a wire is snapped. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) 1-2. DISCHARGING OF THE ST-083

FLEXIBLE BOARD’S CHARGING CAPACITOR (C333)

The charging capacitor (C333) of the ST-083 flexible board is Discharging the Capacitor charged up to the maximum 300 V potential. Short-circuit between the LND390 (positive) and the LND391 There is a danger of electric shock by this high voltage when the (negative) terminals on the ST-083 flexible board with the short jig battery is handled by hand. The electric shock is caused by the about 10 seconds. charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below. LND391 R:1 kΩ/1 W Preparing the Short Jig (Part code: To preparing the short jig, a small clip is attached to each end of a 1-215-869-11) resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent LND390 electrical shock. 1 kΩ/1 W ST-083 board Wrap insulating tape. Capacitor 1-1, 1-3. NOTE IN LENS FRAME

INSTALLATION

When tightening a screw, have both sides of the lens block assembly so as not for the load to depend. Lens holder Lens block assembly P2 × 4 1-4. NOTES ON HANDLING THE LASER DIODE [LASER UNIT (D333)] The laser diode may suffer electrostatic breakdown because of the Note: Adjustment is needed when laser unit (D333) is replaced. potential difference generated by the charged electrostatic load, etc. Refer to “16. Hologram AF Data Input” and “17. Hologram on clothing and the human body. AF Angle Check” of SERVICE MANUAL, ADJ During repair, pay attention to electrostatic breakdown and also use (987626151.pdf). the procedure in the printed matter which is included in the repair parts. The flexible board is easily damaged and should be handled with care. Laser unit (D333) 1-2, 1-5. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory stick”. Unformatted memory stick is inserted. FORMAT ERROR C:13:ss Insert a new “Memory Stick”. Memory stick is broken. MEMORY STICK ERROR E:61:ss Checking of lens drive circuit. When failed in the focus and zoom initialization. — Checking of flash unit or replacement Abnormality when flash is being E:91:ss of flash unit. charged. 1-3E,

COVER SECTION 2 DISASSEMBLY HELP The following flow chart shows the disassembly procedure.

Discharging the Capacitor

DISASSEMBLY DISASSEMBLY DISASSEMBLY DISASSEMBLY

DISASSEMBLY DISASSEMBLY HELP HELP

DISASSEMBLY DISASSEMBLY HELP DISASSEMBLY DISASSEMBLY DISASSEMBLY HELP

SERVICE POSITION

DISASSEMBLY

DISASSEMBLY DISASSEMBLY

HELP

2-1, [SERVICE POSITION] FU-165 flexible board AC power AC IN adaptor It is connection needlessness at the time of a play mode check. DD-195 board Control switch block (GL-51470) BB-004 flexible board SY-089 board Memory stick connector Lens block assembly ST-083 flexible board JK-254 Back light unit flexible board LCD module Color monitor Control switch block (MODE-51470) The procedure for a service position 1 2-2. CABINET (REAR) ASSEMBLY ... (PAGE 2-3) 2 2-3. LCD MODULE ... (PAGE 2-4) 3 2-4. CONTROL SWITCH BLOCK (GL-51470) ... (PAGE 2-4) 4 2-5. CONTROL SWITCH BLOCK (MODE-51470) ... (PAGE 2-5) 5 2-6. CABINET (FRONT) ASSEMBLY ... (PAGE 2-5) 6 2-7. STROBOSCOPE BLOCK... (PAGE 2-6) 7 2-8. SY-089 BOARD ... (PAGE 2-6) 8 2-9. MEMORY STICK CONNECTOR ... (PAGE 2-7) 9 2-10. LENS BLOCK ASSEMBLY ... (PAGE 2-7) 0 2-14. DD-195 BOARD ... (PAGE 2-9) qa 2-15. JK-254 FLEXIBLE BOARD... (PAGE 2-10) 2-2, Note: Follow the disassembly procedure in the numerical order given. 2-1. BATTERY LID 1 Open the BT lid. 2 Two clawsBT lid 3 BT lid Flat head driver 2-2. CABINET (REAR) ASSEMBLY 5 Claw 2 Screw (M1.7) 1 Screw (M1.7) 3 Screw (M1.7) 4 Two screws (M1.7) 6 Cabinet (rear) assembly 2-3, 2-3. LCD MODULE Sheet attachment position and processing the flexible board

LCD

module 1 LCD stopper 4 SY089 board 2 Lever 3 Two claws 7 LCD module Sheet (LCD), adhesive 5 Connector (CN702) Flexible board of LCD module 6 Connector (CN801) 2-4. CONTROL SWITCH BLOCK (GL-51470) 1 Claw 4 Connector (CN703) 5 Control switch block (GL-51470) 2 Claw 2-4, 2-5. CONTROL SWITCH BLOCK (MODE-51470) 3 Screw (M1.7) 4 Control switch block (MODE-51470) Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points of ST-083 flexible board with the short jig about 10 seconds. ST-083 flexible board LND390 2 Connector (CN704) R:1 kΩ/1 W (Part code: 1-215-869-11) LND391 1 Harness (CN753) 2-6. CABINET (FRONT) ASSEMBLY Processing the flexible board 2 Cabinet (front) assembly 1 Two screws (M1.7) 2-5, 2-7. STROBOSCOPE BLOCK 6 Stroboscope block 1 Connector (CN751) 5 Claw 2 Screw (P2) Position of claws Stopper 4 Rotate the condenser holder. Stroboscope block Note: When removing condenser holder, be careful not to break the claw. Condenser holder 2-8. SY-089 BOARD 7 Claw 2 Connector (CN151) 3 Connector 1 Connector (CN705) (CN752) 8 Claw 5 Connector (CN301) 4 Connector (CN701) 9 SY-089 board 6 SCREW (M1.7) 2-6, 2-9. MEMORY STICK CONNECTOR 1 MS protection sheet 4 Claw 2 MS-165 flexible board Sheet attachment position MS-165 flexible board 5 Memory stick connector Memory stick connector MS protection sheet 3 Two screws (P2) 2-10.LENS BLOCK ASSEMBLY 3 Lens block assembly Processing the flexible board Lens block assembly Frame assembly flexible board 2 Two claws Frame 2-7, 2-11.ST-083 FLEXIBLE BOARD Adhesive sheet 5 ST cover 2 ST ornamental plate 4 Three claws 3 Screw (P2) ST cover open. 1 Push the spring. 0 Solenoid 8 Claw 6 Screw (P2) 9 Solenoid cover 7 Screw (P2) qa Two claws qs Two claws qf ST-083 flexible board qd Claw 2-8, 2-12.CONDENSER HOLDER Stroboscope block 1 Claw Note: When removing condenser holder, be careful not to break the claw. : The portion which is easy to break. 2 Condenser holder 2-9, 2-13.CD-441 FLEXIBLE BOARD 7 CCD radiation sheet 5 Radiation sheet (SD) 6 Two screws 1 Three screws 2 Lens holder qd CD-441 flexible board 8 qa Remove these solders. qs IC101 9 Seal rubber (K) 3 Radiation sheet (CD) 0 Optical filter block 4 Radiation sheet (LE) 2-14.DD-195 BOARD 3 Connector (CN081) 4 DD-195 board 1 Screw (P2) DD sheet 5 BB-004 flexible board (CN082) slit Sheet attachment position DD sheet DD-195 board 2-10, 2-15.JK-254 FLEXIBLE BOARD 1 Screw (P2) 2 JK-254 flexible board 2-16.FU-165 FLEXIBLE BOARD 3 Screw (M1.7) 5 Claw DC jack 2 Speaker holder 9 FU-165 8 Remove three solders. flexible board 1 Claw 4 Two claws qa Battery terminal board 0 Claw 2-11, 2-17.CIRCUIT BOARDS LOCATION MS-165 FLEXIBLE SY-089 CD-441 FLEXIBLE JK254

FLEXIBLE

BB-004 FLEXIBLE SW-395 FLEXIBLE FU-165 FLEXIBLE DD-195 ST-083 FLEXIBLE Board Name Function BB-004 FLEXIBLE SY-DD EXTENSION BOARD CD-441 FLEXIBLE CCD IMAGER DD-195 DC POWER IN, DC/DC CONVERTER FU-165 FLEXIBLE DC IN, BATTERY IN JK-254 FLEXIBLE USB, A/V JACK MS-165 FLEXIBLE MEMORY STICK CONNECTOR ST-083 FLEXIBLE FLASH DRIVE, LASER UNIT SW-395 FLEXIBLE MIC, LENS ADAPTOR SWITCH SY-089 CAMERA PROCESS, LENS DRIVE, CAMERA DSP, SH DSP, MEMORY, CLOCK GENERATOR, AUDIO, VIDEO, USB INTERFACE, FRONT CONTROL, AF LASER/IR LED DRIVE, FLASH CONTROL, INTELLIGENT SHOE CONTROL 2-12E, 2003.05.09 Update

HELP Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. MAIN BLOCK SECTION

Radiation sheet (CM) SW-395 flexible board SY-089 board LCD DD sheet module SY089 board DD-195 board Sheet (LCD), adhesive Flexible board of LCD module Radiation sheet (LE) Lens block section Radiation sheet (CD) Radiation sheet (SD) MS-165 flexible board Lens block assembly Memory stick connector MS protection sheet Frame assembly flexible board

HELP

,

COVER

3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2),

COVER SECTION 3 3. BLOCK DIAGRAMS BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. LENS UNIT LENS IRIS CD-441 FLEXIBLE BOARD SY-089 BOARD (1/2) PANEL UNIT (SHUTTER) CA ADI00 CA AD00 CN801 Q102 CN151 ı ıCA ADI13 1 - 4 6 29 - 32 34 CA AD13 PANEL R VR 15 BUFFER CCD OUT 14 6 25 212 40 19 21ı8- 10 36 - 38 12 - 14 16 207 PANEL G 39 20 VG 20 LCD901 20 IC1525 5 38 56 57 40 - 42 18 - 27 PANEL B VB RG, H1B, H2B 61 - 64 45 - 47 204 3821 IC801 21 2272CAMERA Q801, 802 225 HDO2284MODULE CA HDI 43 PSIG PSIG COLOR46 50 IC681 22 CA HD 8 229 PANEL V LCD DRIVE, 25 19 3 21 (1/12) CA FDI 42 TIMING DRIVE

LCD

7 V2, V4, V5A, V5B, ı 47 48 19 CA FD 24 SIGNAL 9 XRST SYS GENERATOR 2

MONITOR

SHUTTER ZOOM FOCUS IR FILTER IRIS ı 10 GENERATOR, 20 9 (7/12) 2V6, V7A, V7B, V8 3 RGT, HCK1, HCK2, ı MOTOR MOTOR MOTOR MOTOR MOTOR 9 14ı ı SRAM 13 411 4628 HST, WIDE, DWN,

MMMMMIC101 ı 20 (2/12) ı 1214 32 XSG3A,

58 24 48 14 EN, VCK, VST, COM BL ON 15 13XSG3B, CCD 31 17XSG5A, 23 IMAGER 1 30 3 39 8 MCK12 32 182 V1A, V1B, V3A, V3B 31 7 41 XSG5B 9 49 96 BL LEV 28 ı 23 ZOOM FOCUS IR 4 33 9 45 12 41 29 35 IC151 SENSOR SENSOR SENSOR 5 34 11 48 13 42 CAM SO, XCAM SCK, XCAM RESET CN702 D901 V DRIVER 45 BL THL Vhold 10 25 64 (1/12) XV6 1 51 23 Vst XV4 6 29 1 49 21 XV3 48 TG CLK BL L 43 7 88 BACKLIGHT 47 XV5 11 27 H1A, H2A21IC601 2833CAMERA DSP, 256M SDRAM BL THL, BL L OVERALL TH101 X581 (4/12) BL ON, BL LEV (2/2)CCD TEMP CCD TEMP 36 CCD TEMP 27MHz IC581SENSOR 4 Q606 (PAGE 3-4)2 CLOCK CKIO16 CV OUT GENERATOR USB CLK 215 BUFFER (6/12) 11 278 AU AINL 272 AU AOUTCN301 IC302 IR FILTER IN, 1 IR FILTER± 6 2 IR FILTER OUTı 1977 IR FILTER4 3 199 65 - 69MOTOR DRIVE 71 - 81 MC D00 - D15 MC D00 - D15 IC303 (3/12) 29 - 41 LENS DRIVER 43 - 54 MC A01 - A25 MC A01 - A07 (3/12) HR EN0, USB CLK OVERALL 12 FOCUS A, A, B, B 20 21 FOCUS 5 HR DIR0A, HR DIR0B 233ı C2 C3 SP VOL23 24 MOTORıı(2/2)19 DRIVE 8 235 C8 D7 1 D9 E1 (PAGE 3-3) HR EN1, E4 E9 MC D00 - D15 13 VAMP ON 32 ZOOM A, A, B, B 37 38 ZOOM 1 HR DIR1A, HR DIR1B 237 F2 F3 50 XAU SP MUTEı MOTORıı39 41 - 45 39 41 42 DRIVE 4 239 F7 F8 G2 G6 MC D00 - D15 47 49 51 52 29 XAU LINE MUTE HR EN2, H2 J9 54 56 - 60 124 AU HGL SEL 24 IRIS 9 XAU POWER SAVEIRIS A, A, B, B 14 15 HR DIR2A, HR DIR2B 241 IC503 62 - 64 66 25ı 17 18 MOTOR ı ı27 12 243 68 - 70 72DRIVE 32M MC A01 - A25 73 75 76 FLASH A3 A4 78 79 81 129 XUSB DREQ0, XUSB DACK0MSHUT ON 20 SHUTTER 47 246 (6/12) B3 B4 83 - 88 90 130 SHUTTER± 43 MSHUT EN C4 D4ı MOTOR 48 196 92 93 95 97 208 XUSB DREQ1, XUSB DACK1 23 46 D6 G4DRIVE 31 210H3 H4 H6 H7 MC A01 - A21 6 IR SENS RST XIR RST SENS 185 J3 J4 D704 J6 J7 IC501 (MS ACCESS) 8 F RST SENS XFC RST SENS 192 K3 K4 232 K6 - K8 MC CAM,

MS-165

SH DSP, 216 FLEXIBLE 28 Z RST SENS1, 2 XZM RST SENS1, 2 187 MEMORYFLASH 29 184 BOARD STICKXRST SYS 94 XRST SYS (5/12) IC602 140 CN705 LENS TEMP TEMP OUT LENS TEMP124248 MS DIO, MS BS, DIO, BS, SENSOR 10 (4/12) SYS V 227 SYS V 164 213 MS SCLK 2 SCLK 8179 249 EXT STRB ONı44STRB ON 215 6 2248 INT56IC304 C4 B4 CAM SO, XCAM SCK CAM SI, CAM SO, XCAM SCK, XCAM RESET ı

EVR ST-083 FLEXIBLE BOARD (1/2) USB CLK 220(D/A CONV.)

CN751 (1/2) B1 (3/12) C1 SP VOL LD OUT IC2812552PRELAMP AF CONTAF LASER A2 A3 DAC STB 19 PD OUT 27 1 DRIVE 4 CKIO CKIO 187 (11/12) CCD TEMP 230 XMS IN D333 LENS TEMP Q501229 (LASER UNIT) EEPROM, 35 LED XAE LOCK LED IC502 SO, SI, SCK DRIVE 2 202 EEPROMıı(6/12) 4 204 190 FR SI, FR SO, XFR SCK

SW-395 FLEXIBLE BOARD (1/2) 191 OVERALL

PRELAMP AF ON 7 (2/2) CN753 (1/2) Q281 PD LEV 2236 17 HSHOE CONT (PAGE 3-3) IR LEDK5IR LED 27 32 EXT STRB CONT D101 6 DRIVE (IR EMITTER) XRST SYS SYS V

A : VIDEO SIGNAL EXT STRB ON A : AUDIO SIGNAL STRB ON A : VIDEO/AUDIO SIGNAL 05

3-1 3-2 MSHUT REF CAM SO, XCAM SCK, XCAM RESET CAM SI, CAM SO, XCAM SCK ADDRESS BUS MC A01 - A25 DATA BUS MC D00 - D15,

COVER 3. BLOCK DIAGRAMS

3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-089 BOARD (2/2) JK-254 FLEXIBLE BOARD DD-195 BOARD FU-165

CN752 FLEXIBLE CV OUT IC101 V OUT V OUT J201 A : VIDEO SIGNAL IC002 , Q0016 4 13 CN081 BOARD VAMP ON VIDEO AMP AU OUT AU OUT A/V OUT A : AUDIO SIGNAL SWITCH7 Q004, Q005 (8/12) 9 (MONO) A : VIDEO/AUDIO SIGNAL (1/2) 1ACV UNREG ı ACV UNREG1 J101 AV JACK IN AV JACK IN ST UNREG 8BATT/XEXT BATT/XEXT1 DC IN1192- 5 IC901 CN201 ı ACV GND1 41 - 44 MC D00 - D15 46 - 48 USB 97 USB D 2± USB D 2± 78 - 80 INTERFACE 993323 82 107 (9/12) BATT UNREG BATT UNREG1 + USB JACK IN USB JACK IN ıVCC 38 - 40 7651(USB) D004 30BATT SIG BATT SIG1 BT901 MC A01 - A07 31 S 104 - 106 BATTERYBB-004 TERMINAL XUSB DREQ0, XUSB DACK0 10 FLEXIBLE −

OVERALL (1/2) 181 52 XRST SYS BOARD 21(PAGE 3-2) BATT GND1XUSB DREQ1, XUSB DACK1 14 35 32

55 CN701 CN401 CN402 CN082 ı USB CLK 3936 BACKUP VCC 6 VL 3V VL 3VIC403 3 59 59 22 BT101 EVER 3.0V 8 D403 LITHIUMINITIAL RESET, 2 BATTERYBACK UP VCC AU AINL 5 (10/12) 7 LANC 5.5VH4 B4 AU AOUT H5 A2 SP ± 58 SP ± 58 SP ± 19 SP ± SP VOL SP901J3 D1 60 60 20 XAU SP MUTE S081 SPEAKERB2 XAU LINE MUTE RESETC8 Q402 (1/2) AU HGL SEL USB JACK ING8 9 73 XRESET 54 XRESET FR 54 XAU POWER SAVE H9 IC201 AV JACK IN 11 AUDIO AMP BEEP ONIC003, (8/12) F2 49 Q408 Q019 BATT UNREG Q407 BATT SI BATTERY LANC 5.5V DC/DC MIC901 SW-395 FLEXIBLE BOARD (2/2) BEEP 43 BATT SIG BATT SIG ACV UNREGCN753 BATT SO CHARGE 48 48 CONVERTER MICROPHONE E1 MODULATOR 74 42CN101 (2/2) DETECTOR (1/2) MIC SIG 2 10 B8 79 47 INIT CHARGE 50 INIT CHARGE 50 INIT CHARGE D102 Q406 (1/2) 48 FAST CHARGE 52 FAST CHARGE 52 FAST CHARGE D 1.5V (SELF TIMER) XSELF TIMER LED LED SELF TIMER LED8 BATT/XEXT BATT/XEXT BATT/XEXT D 2.9VDRIVE 19 8 46 46 S101 A 2.9VKEY AD4 KEY AD4 LENS ADAPTOR 2 59 PANEL 2.9V DETECT 29 CAM 3.2V X401 USB 3.2V IC402 10MHz28 CAM P 5V FR SI, FR SO, XFR SCK FR SI, FR SO, XFR SCK ı FRONT Q002 CAM 15V IC001 25 51 3 BL THL, BL L BL THL BL THL SWITCHING CAM –7.5V ACV UNREG CONTROLLER X402 42 42XRST SYS XRST SYS 77 (10/12) DC32.768kHz PANEL 13.5V SYS V SYS V 5232 OVERALL (1/2) BL L

CONTROL

38 BL L 38 59 (2/2) XMS IN Q403 MS IN 6 (PAGE 3-2) BL ON, BL LEV BL LEV 36 BL LEVEL 36 60 BL ON 34 BL ONQ708 34 48

OVERALL (1/2) HSHOE CONT Q703EXT STROBE LANC IN 20 4 4

(PAGE 3-2) 2 EXT STRB ON IC401SWITCH LANC DC 10 39 21 UNREG SO, UNREG SCK 8 DATA, CLK 8 UNREG SO, UNREG SCK LANC 12 40 EXT STRB CONT DRIVER LANC OUT Q705, Q706 INTE STRB ON 11 (10/12)

HOT

D401 XLANC PWR ON XAE LOCK LED 7 CONTROL SWITCH BLOCK (GL-51470) CONTROL SWITCH BLOCK Q409, Q410 STRB ON D405 CN703 (MODE-51470) SWITCH S251 - S261 55 S102 LANC SIG ı KEY AD0 - AD2 KEY AD0 - AD2 ı FUNCTION 57 6 KEY NIGHTFRAMING (OFF) NIGHTSHOT INTE Q701, Q702 J301 CN751ST-083 FLEXIBLE BOARD (2/2) (2/2) SALA SIG LANC SIGACC EXT1 STB ON SWITCH32 CN704 LANC SIG 30 Q405, Q411 (1/2), Q412 KEY AD2 EXECUTE S105 ACC XLANC JACK IN S106 (UP)33 LANC JACK 37 DIAL A, B Program Dial A, B 23 DIAL A, B JOG DIAL LANC DC LANC JACK IN2 INDETECT 10 38 24 ZOOM S301 KEY AD358 KEY AD3 9 S101 STROBE OPEN DETECT 28 XSTRB POPUP 45 S104 (DOWN) Q411 XPWR ON XPWR ON S103 PLUNGER (2/2) Q751 1 15 POWER (SHUTTER) ı STRB PLUNGER PLUNGER XSHTR ON 39 DRIVE 78 4 XSHTR ON XSHTR ON 2 XAE LOCK SW 5 XAE LOCK ON XAE LOCK ONFLASH D332 T331 Q331, Q332 UNIT Q753,Q7547 2 10XE_H (Anode) ı ST UNREG5 1 ST UNREG 35 XPB ON, MODE DIAL2, MODE DIAL, XSETUP ON 11 XPB ON, MODE DIAL2, MODE DIAL, XSETUP ON S108 12 54 MODEQ402 (2/2) 13+ DIAL 4 TRANS STB CHARGE 60 14 DRIVE 46 LED PWR LED ON D1052 L331 3 XSTRB PWRSAVE XSTRB PWR SAVE 17 DRIVE 16 (POWER) TRIGGER 5 75 C333 XSTB FULL 34 15 XTALLY LED 18 D106 CHARGING Q406 (2/2) (SELF TIMER/RECORDING)

CAPACITOR

STB FULL LED XCHARGE LED D1081 16 21Q752 DRIVE (FLASH/CHG) AE LOCK LED D107 XE L (Cathode) IC331 19 (AE/AF LOCK) INTE SALA SIG LANC SIG LANC SIG Q334 2 FLASH44STRB ON HOT HOT HOTCONTROL 6 INTTELLIGENTINTE STRB ON INTE STRB ON INTE STRB ON 7 SHOE LANC JACK IN2 LANC JACK IN2 LANC JACK IN2 3-3 3-4 INIT CHARGE FAST CHARGE,

COVER 3. BLOCK DIAGRAMS

3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

FU-165 DD-195 BOARD FLEXIBLE IC002 , Q001 F001 BOARD CN081 SWITCH BB-004

ACV UNREG1 1 LF001 (1/2) F002 FLEXIBLE J101 ı BOARD DC IN 8BATT/XEXT1 9 BATT/XEXT Q004, Q005 F004 (2/2) 10 CHARGEACV GND1 ı CONTROL D009 D008 17 CN082 CN402 CN401 (2/2) (2/2) (2/2) BATT UNREG1 23 F006 D010 L018 L006 D011 L010 D012+ ı ST UNREG 13 ST UNREG BT901 BATT SIG1 30 D004 S 31 BATT SIG 5 5BATTERY ACV UNREGIC003, TERMINAL − BATT UNREG Q019 18 DC/DC 21 CONVERTERBATT GND1 32 (1/2) ı BT101 VL 3V 22 VL 3V LANC 5.5V

LITHIUM BATTERY

IC001 DC CONTROL (2/2)

BB-004 Q011, Q015 L007 FLEXIBLE 31 31VCC2 41 SWITCHING D 1.5V 33 D 1.5V 33 SY-089 BOARD (1/2) BOARDIC403 35 35(1/2)

INITIAL RESET, OUT1p 36 BACK UP VCC OUT1n 37 (10/12) CN701 CN401 CN402 CN082 VIN1– 55 (1/2) (1/2) (1/2) (1/2) L003 Q008, Q018 Q020 (1/2) 21 21 L017 23 23 VBAT 3 59 VL 3V CAM P 5V CAM P 5V L401 59 SWITCHING 25 25 6 VOUT D403 27 27 PREEND OUT6p 28 29 292 EVER 3.0V 8 VRO VIN77LANC 5.5V 7 OUT6n 29 OUT6S 18 EVER 3.0V 9 EVER 3.0V VIN6– 50 9 EVER 3.0V 56 VCC1 Q010, Q014 L009 L015 CAM 3.2V 47 CAM 3.2VVCC4 19 SWITCHING 47 POWER 2 47 RST 49 49 B (PAGE 3-7) IC401 LANC 5.5V L016 USB 3.2V 51 USB 3.2V 51 LANC DRIVER OUT4p 30Q401 53 53 (10/12) OUT4n 31 LANC DC 14 LANC DC VIN4– 53 Q023 L001 D015 IC402 BL H BL HSWITCHING 40 40 FRONT CONTROLLER (10/12) OUT2n 35 BACKUP OVP2 58 VCC Q007, Q017 Q012, Q016XLANC ON 18 L002 L008 L012POWER2D2.9V 37 D 2.9V 37 SWITCHING SWITCHING 39 39 (PAGE 3-7) A BATT UNREG Q020 (2/2)BATT SENS 67 57 57 41 41 ACV UNREG L013 ACV SENS 68 55 55 OUT5p 38 A 2.9V 43 A 2.9V 43 D 1.5V 66 DD CON SENS OUT5n 39 45 45 OUT5S 43 L014 PANEL 2.9V PANEL 2.9V FAST CHARGE 11 11FAST CHARGE 48 52 52 VIN5– 52 INIT CHARGE 47 INIT CHARGE50 50 BL THH BL THH BATT/XEXT 44 44 BATT/XEXT 8 46 46 Q408 OUT3p 32 BATT SI 43 BATTERY OUT3n 33 CHARGE 48 BATT SIG 48 VIN3– 54 BATT SO 42 Q009DETECTOR CAM –7.5V CAM –7.5V VCC3 42 SWITCHING 13 13 76 2 SYS DD ON 2 SYS DD ON VCC5 20 SYS DD ON 57 CONT 22 6 XCS 6 XCS DDCONXCS DDCON 44 XCS DATA UNREG SO OUT10 22 UNREG SO 208845 DATA 21 4 CLK 4 UNREG SCK AMPIN 4 UNREG SCK 46 CLK AMPOUT 5 L004 Q024 D014 STB PLUNGER CAM 15V 17 CAM 15V 1778 STB PLUNGER IN10− 3 SWITCHING STB CHARGE 19 1946 STB CHG FB10 2 Q021, Q022 PANEL 13.5V PANEL 13.5V 13.5V REG 15 15 BL ON 34 BL ON 34 BL ON 48 ONOFF2 OUT9 23 FB9 79 IN9– 80 SCP9 1 3-5 3-6 FAST CHARGE INIT CHARGE VL 3V BATT UNREG ACV UNREG LANC 5.5V,

COVER 3. BLOCK DIAGRAMS

3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-089 BOARD (2/2) ST-083 FLEXIBLE BOARD FLASH UNIT

CN751 T331 IC151 Q753, Q754 ST UNREG L752 ST UNREG7VDRIVERı 12 (1/12) STB CHARGE STB CHARGE STB PLUNGER Q751 PLUNGER CAM P 5V STRB PLUNGER 37ı L154 39 L153 IC152 STB PLUNGER L152 IC281 CAM 3.2V FB152 CAMERAIC331 AF LASER M 5V MODULE DRIVE 3 FLASH (1/12)

POWER1A(11/12) CONTROL(PAGE 3-5) J301 CD-441 FLEXIBLE BOARD

LANC DC FB752 LANC DC ACC34 Q152, Q153 CN151 CAM 15V L151 CAM 15V IC101 CAM −7.5V 11BL ON CAM −7.5V 38 FB101 CCD PANEL UNIT IMAGER EVER 3.0V Q803 CN801 D 1.5V PANEL 13.5V VDD 7 FB507 IC503D 2.9V D801 LCD901 32M FLASH

VDDG

9 (6/12) CN701 IC801 BL ON CRext COLOR (2/2) LCD DRIVE, PWM 31 16L802 XPOFF LCD 1 L803 TIMING XPOFF 16 IC502MONITOR ST UNREG GENERATOR REF 6 14

REF

3 EEPROM 5 (7/12) (6/12)D901 PANEL 13.5V 15 CN702 PANEL 2.9V PANEL 2.9V BL THH11 3 BL THH BL THH BL H D704 MS-16544 6 BL H BL H (MS ACCESS) FLEXIBLE40 BACKLIGHT 198 BOARDPTM (6) Q704 CN705 VCC MEMORY IC50179FB505 STICKCONTROL SWITCH BLOCK MC CAM, (MODE-51470) L502 SH DSP, CN704 FB506 EVER 3.0V D108

FLASH

20 (FLASH/CHG) (5/12) D32/PTA (7) 30 MS POWER ON D 2.9V D105 17 (POWER) IC681 D106 D 1.5V SIGNAL SELF TIMER/RECORDING IC302D 2.9V GENERATOR, SRAM D107 CAM P 5V L304 IR FILTER (2/12) (AE/AF LOCK) MOTOR

DRIVE

(3/12) IC581 SW-395 FLEXIBLE BOARD FB582 A 2.9V CLOCK IC304CN753 L302 IC303 GENARATOR PANEL 2.9V D102 EVR L303 (6/12) 7 (SELF TIMER)

LENS

(D/A CONV.) DRIVER (3/12) IR LEDA3D101 (3/12) LENS UNIT 4 (AF ILLUMINATOR) IC901 Q304 (1/2) CN301 USB 3.2V L901 D 2.9V IR SENS VCC5 IR FB901 USB SENSORINTERFACE (9/12) XIR SENS LED

POWER 1 Q305B L101 IC101(PAGE 3-6) F RST VCC FOCUSVIDEO AMP 9

47 CAM 3.2V CAM 3.2V SENSOR(8/12) 49 XFC RST LED 17 CAM 15V CAM 15V Q304 (2/2) 19 L202 Z RST VCC ZOOM CAM −7.5V CAM −7.5V IC201 31 13 SENSORL201 AUDIO AMP 51 USB 3.2V USB 3.2V (8/12) XLENS RST LED 23 CAM P 5V 25 CAM P 5V 27 AU 2.9V 29 IC601 43 A 2.9V A 2.9V L602 CAMERA DSP, 45 256M SDRAM L601 (4/12) 33 D 1.5V D 1.5V FB602 XIR SENS LED 35 PI007 XFC RST LED FB604 PI003 195 37 XLENS RST LEDD 2.9V D 2.9V FB603 PI001 19839 IC602

XOR

(4/12) 3-7 3-8E CAM 3.2V CAM 15V CAM −7.5V USB 3.2V D 2.9V D 1.5V CAM P 5V A 2.9V CAM DD ON,

COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS

4-1. FRAME SCHEMATIC DIAGRAM12345678910 11 12 13 14 15 16 17 18 19

FRAME SCHEMATIC DIAGRAM A CCD CONTROL SWITCH CD-441 BLOCK FLEXIBLE BOARD (MODE-51470)

MIC901

B INTELLIGENT CN101 2P MICROPHONE SHOE MIC_GND 1

MIC_SIG 2 CN753 11P REG_GND 11 MIC_SIG 10 MIC_GND 9 XSELF_TIMER_LED 8 PANEL_2.9V 7 SW-395

C LENS UNIT IR_LED_K 6

CN301 39P FLEXIBLE IR_LED_K 5

OVF 1 IR_FILTTER+ BOARDIR_LED_A 4

2 IR_FILTTER+ IR_LED_A33IR_FILTTER- KEY_AD424IR_FILTTER- REG_GND15IR_SENS_VCC 6 IR_SENS_RST

D 7 IR_SENS_GND CN703 6P

8 F_RST_SENS KEY_AD2 6

LENS 9 F_RST_VCC KEY_AD1 5 CONTROL

10 TEMP_OUT KEY_AD0 4 SWITCH 11 TEMP_GND REG_GND 3 BLOCK 12 FOCUS_B REG_GND 2 (GL-51470) 13 FOCUS_B NC 1 14 FOCUS_B

E 15 FOCUS_B CN705 8P

16 FOCUS_A VSS 8 17 FOCUS_A VCC 7 18 FOCUS_A SCLK 6 19 FOCUS_A MS-165 INT 5 MS 20 SHUTTER- DIO 4 FLEXIBLE 21 SHUTTER- NC 3 BOARD CONNECTOR 22 SHUTTER+

F BS 223 SHUTTER+

VSS 1 24 IRIS-B 25 IRIS-B 26 IRIS-A 27 IRIS-A 28 Z_RST_SENS1 29 Z_RST_SENS2 30 Z_RST_GND

G 31 Z_RST_VCC SY-089 CN701 60P CN082 60P CN081 39P

32 ZOOM_B BOARD 60 SP- VL_3V 59 59 VL_3V SP- 60 BATT_GND1 39 33 ZOOM_B 58 SP+ BATT_UNREG 57 57 BATT_UNREG SP+ 58 BATT_GND1 38 34 ZOOM_B 56 REG_GND ACV_UNREG 55 55 ACV_UNREG REG_GND 56 BATT_GND1 37 35 ZOOM_B 54 XRESET_FR USB_3.2V 53 53 USB_3.2V XRESET_FR 54 BATT_GND1 36 36 ZOOM_A 52 FAST_CHARGE USB_3.2V 51 51 USB_3.2V FAST_CHARGE 52 BATT_GND1 35 SP901 37 ZOOM_A 50 INIT_CHARAGE CAM_3.2V 49 49 CAM_3.2V INIT_CHARAGE 50 BATT_GND1 34 SPEAKER 38 ZOOM_A 48 BATT_SIG CAM_3.2V 47 47 CAM_3.2V BATT_SIG 48 BATT_GND1 33

H 39 ZOOM_A 46 BATT/XEXT A_2.9V 45 45 A_2.9V BATT/XEXT 46 BATT_GND1 32

44 BL_THH A_2.9V 43 43 A_2.9V BL_THH 44 BATT_SIG1 31 42 BL_THL D_2.9V 41 41 D_2.9V BL_THL 42 BATT_UNREG1 30 40 BL_H D_2.9V 39 39 D_2.9V BL_H 40 BATT_UNREG1 29 38 BL_L D_2.9V 37 37 D_2.9V BL_L 38 BATT_UNREG1 28 36 BL_LEVEL D_1.5V 35 35 D_1.5V BL_LEVEL 36 BATT_UNREG1 27

JK-254 34 BL_ON D_1.5V 33 33 D_1.5V BL_ON 34 BATT_UNREG1 26

FLEXIBLE BT10132 REG_GND D_1.5V 31 31 D_1.5V REG_GND 32 BATT_UNREG1 25I BOARD 30 REG_GND CAM_P_5V 29 29 CAM_P_5V REG_GND 30 BATT_UNREG1 24 LITHIUMCN752 14P 28 REG_GND CAM_P_5V 27 27 CAM_P_5V REG_GND 28 BATT_UNREG1 23 BATTERY 1 USB_GND 26 REG_GND CAM_P_5V 25 25 CAM_P_5V REG_GND 26 VL_3V 22 2 USB_D+ 24 REG_GND CAM_P_5V 23 23 CAM_P_5V REG_GND 24 BATT_GND1 21 CN201 5P 3 USB_D- 22 REG_GND CAM_P_5V 21 21 CAM_P_5V REG_GND 22 SP+ 20 GND54USB_GND 20 REG_GND CAM_15V 19 19 CAM_15V REG_GND 20 SP- 19 ID45USB_JACK_IN 18 REG_GND CAM_15V 17 17 CAM_15V REG_GND 18 BATT_GND1 18 D+ 3 6 STATIC_GND (USB) 16 REG_GND PANEL_13.5V 15 15 PANEL_13.5V REG_GND 16 ACV_GND1 17

J D- 2 7 STATIC_GND 14 REG_GND CAM_-7.5V 13 13 CAM_-7.5V REG_GND 14 ACV_GND1 16

VCC18GND_GUARD(REG_GND) 12 REG_GND PANEL_2.9V 11 11 PANEL_2.9V REG_GND 12 ACV_GND1 15 9 A_OUT 10 REG_GND EVER_3.0V99EVER_3.0V REG_GND 10 ACV_GND1 14 10 GND_GUARD(REG_GND) 8 DATA LANC_5.5V77LANC_5.5V DATA 8 ACV_GND1 13 11 AV_JACK_IN 6 XCS ST_UNREG55ST_UNREG XCS 6 ACV_GND1 12 FU-165 J201 12 GND_GUARD(REG_GND) 4 CLK ST_UNREG33ST_UNREG CLK 4 ACV_GND1 11 FLEXIBLE 13 V_OUT A/V OUT 2 SYS_DD_ON ST_UNREG11ST_UNREG SYS_DD_ON 2 ACV_GND1 10 (MONO) 14 REG_GND BOARD BATT/XEXT1 9

K ACV_UNREG1 8

ACV_UNREG1 7 J101 ACV_UNREG1 6 DC IN

DD-195 ACV_UNREG1 5 BOARD ACV_UNREG1 4

ACV_UNREG1 3 ACV_UNREG1 2 ACV_UNREG1 1

L BT901 BATTERY TERMINAL M LCD901 COLOR LCD MONITOR J301 ST-083

ACC FLEXIBLE BOARD

D901 BACKLIGHT N

05 PANEL UNIT 4-1 4-2 FRAME CN702 6P 1 BL_THL 2 N.C 3 BL_THH 4 BL_L 5 N.C 6 BL_H CN801 24P 1 TEST1 CN151 39P 2 COM GND 39 3 VST CAM_-7.5V 38 4 VCK GND 37 5 EN CCD_TEMP 36 6 DWN GND 35 7 VDD V1A 34 8 VSS V1B 33 9 VDDG V2 32 10 VSSG V3A 31 11 CS V3B 30 12 WIDE Vst 29 13 HST V4 28 14 REF V5A 27 15 SOUT V5B 26 16 CRext Vhold 25 17 HCK2 V6 24 18 HCK1 V7A 23 19 PSIG V7B 22 20 G V8 21 21 R GND 20 22 B VSUB 19 23 RGT VSUB_CONT 18 24 TEST2 GND 17 GND 16 GND 15 CCD_OUT 14 GND 13 GND 12 CAM_15V 11 CN751 39P GND 10 1 STB_FULL GND92N.C. H2B83M_5V H1B74STRB_ON GND65XSTRB_PWRSAVE RG56N.C. GND47ST_UNREG H2A38ST_UNREG H1A29ST_UNREG GND 1 10 ST_UNREG 11 ST_UNREG 12 ST_UNREG 13 N.C. 14 N.C. C704 25P 15 REG_GND NC 25 16 REG_GND Program_Dial_A 24 17 REG_GND Program_Dial_B 23 18 REG_GND KEY_AD2 22 19 REG_GND XCHARGE_LED 21 20 REG_GND EVER_3.0V 20 21 REG_GND AE_LOCK_LED 19 22 REG_GND XTALLY_LED 18 23 REG_GND D_2.9V 17 24 REG_GND PWR_LED_ON 16 25 LD_OUT XPWR_ON 15 26 REG_GND XSETUP_ON 14 27 PD_OUT MODE_DIAL 13 28 XSTRB_POPUP REG_GND 12 29 LANC_GND MODE_DIAL2 11 30 LANC_SIG XPB_ON 10 31 LANC_GND KEY_AD3 9 32 EXT1_STB_ON LANC_JACK_IN2 8 33 ACC_XLANC_JACK_IN INTE_STRB_ON 7 34 LANC_DC HOT 6 35 N.C. REG_GND 5 36 N.C. LANC_SIG 4 37 STRB_PLUNGER REG_GND 3 38 STRB_PLUNGER XSHTR_ON 2 39 STRB_PLUNGER XAE_LOCK_ON 1 CN401 60P

BB-004 FLEXIBLE BOARD

CN402 60P, COVER 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ

LµiFn. 5k0 V or less are not indicated except for electrolytics Pattern box

and tantalums. • Chip resistors are 1/10 W unless otherwise noted. kΩ=1000 Ω, MΩ=1000 kΩ. • Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum L capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. Example C541 L452 22U 10UH TA A 2520 Front of the lens Kinds of capacitor Case Size L = About 25 cm External dimensions (mm) • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. 2. Adjust the distance so that the output waveform of In such cases, the unused circuits may be indicated. Fig. a and the Fig. b can be obtain. • Parts with ★ differ according to the model/destination. H Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ LineABA=BBA• B: B– Line Fig. a (Video output terminal output waveform) • J : IN/OUT direction of (+,–) B LINE. • C: adjustment for repair. Electronic beam • A: VIDEO SIGNAL (ANALOG) scanning frame • A: AUDIO SIGNAL (ANALOG) • A: VIDEO/AUDIO SIGNAL CRT picture frame • A: VIDEO/AUDIO/SERVO SIGNAL • A: SERVO SIGNAL • Circled numbers refer to waveforms. (Measuring conditions voltage and waveform) • Voltages and waveforms are measured between the Fig.b (Picture on monitor TV) measurement points and ground when camera shoots color bar chart of pattern box. They are reference values When indicating parts by reference number, please and reference waveforms. include the board name. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Note : The components identified by mark 0 or Note : Les composants identifiés par une marque dotted line with mark 0 are critical for safety. 0 sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifie. 4-5 Yellow Cyan Green White Magenta Red Blue,

COVER

4-2. SCHEMATIC DIAGRAMS

Link

CD-441 FLEXIBLE BOARD (CCD IMAGER) BB-004 FLEXIBLE BOARD (SY-DD EXTENSION BOARD) ST-083 FLEXIBLE BOARD FU-165 FLEXIBLE BOARD (FLASH DRIVE, LASER UNIT) (DC IN, BATTERY IN) SW-395 FLEXIBLE BOARD (MIC, LENS ADAPTOR SWITCH) CONTROL SWITCH BLOCK (GL-51470) JK-254 FLEXIBLE BOARD (USB, A/V JACK) CONTROL SWITCH BLOCK (MODE-51470) MS-165 FLEXIBLE BOARD (MEMORY STICK CONNECTOR) COMMON NOTE FOR SCHEMATIC DIAGRAMS,

COVER 4-2. SCHEMATIC DIAGRAMS CD-441 FLEXIBLE BOARD

For Schematic Diagram • Refer to page 4-49 for printed wiring board. 12345678CD-441 FLEXIBLE BOARD Note:Voltage and waveform of mounted on CD-441 flexible board can not be measured because they are mounted by the side of the lens.

A CCD IMAGER(CCD BLOCK)

XX MARK:NO MOUNT LND101 39 GND

B LND102 38 CAM_-7.5V

LND103 37 GND LND104 36 CCD_TEMP LND105 TH10135 GND LND106 34 V1A LND107 33 V1B LND108 32 V2 LND109 31 V3A LND110 30 V3B

C LND111 29 Vst

LND112 28 V4 LND113 27 V5A LND114 26 V5B LND115 25 Vhold LND116 24 V6 LND117 23 V7A

D LND118 22 V7B

SY-089 LND119 21 V8 (1/12) LND120 20 GND CN151 LND121 C103 R103 (PAGE 4-9) 19 VSUB R101 XX 470k LND122 18 VSUB_CONT 1500 R1061/10W 14 13 12 11 10987654321Q101 0 LND123 17 GND UN9213J-(K8).SO LND124 16 GND SWITCH C101 0.1u 16V LND125 15 GND LND126 14 CCD_OUT R104 IC101

E 3300LND127 13 GND CCD IMAGER

IC101 LND128 12 GND ICX455AQF-13 LND129 11 CAM_15V LND130 10 GND C105

XX

LND131 9 GND 15 16 17 18 19 20 21 22 23 24 25 26 27 28 LND132 8 H2B LND133 7 H1B

F LND134 6 GND Q102

LND135 5 RG 2SC4250(T5LSONY1) LND136 4 GND BUFFER LND137 3 H2A LND138 2 H1A LND139 1 GND FB101 C106 R110 XX 680 SIGNAL PATH 16V

G C108 C107 C109 C110

VIDEO R111 0.1u 0.22u 10u 0.1u Precautions for Replacement of CCD Imager 0 16V 16V 16V 16V SIGNAL • The CD-441 flexible board mounted as a repair part is not equipped with a CCD imager. Y/CHROMA When replacing this board, remove the CCD imager from the REC old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section.

H • As the CCD imager may be damaged by static electricity from

its structure, handle it carefully like for the MOS IC.

In addition, ensure that the receiver is not covered with dusts

05 nor exposed to strong light. 4-7 4-8 CD-441 VOUT V8 GND V7B GND V7A GND v6 VDD Vhld RG V5B H2B V5A H1B V4 SUB Vst CSUB V3B NC V3A VL v2 H1A V1B H2A V1A, Schematic diagrams of the SY-089 and DD-195 boards are not shown. Pages from 4-9 to 4-36 are not shown.,

COVER 4-2. SCHEMATIC DIAGRAMS ST-083 FLEXIBLE BOARD

For Schematic Diagram • Refer to page 4-57 for printed wiring board. 12345678910

ST-083 FLEXIBLE BOARD A FLASH DRIVE,LASER UNIT(STROB BLOCK) XX MARK:NO MOUNT NO MARK:REC/PB MODE

LND305 LND389 39 STRB_PLUNGER STRB_PLUNGER LND388 38 STRB_PLUNGER LND304 PLUNGER

B LND387 37 STRB_PLUNGER REG_GND

LND386 36 N.C. LND385 35 N.C. 4 FB302 1 LND384 34 LANC_DC 5 J301 LND383 33 ACC_XLANC_JACK_IN 2 ACC LND382 32 EXT1_STB_ON 7 LND390 FB305 LND381 31 LANC_GND + SIDE LND380 30 LANC_SIG LND391 FOR DISCHARGING

C LND379 29 LANC_GND S301 2.PD 1.LDSTROBE OPEN GND

LND378 28 XSTRB_POPUP DETECT LND377 27 PD_OUT D333 LND376 26 REG_GND LASER 3.GND UNIT LND375 25 LD_OUT R302 (Note) 5.6 LND374 24 REG_GND LND373 23 REG_GND LND372 22 REG_GND153

D 1LND371 21 REG_GND P LND331 SY-089 SLND370 20 REG_GND XE_H

(11/12) 2 4 CN751 LND369 19 REG_GND D332 Anode R337 (PAGE 4-29) 0 R331 LND368 18 REG_GND 5600 R332 F HAU160C030TP 1M 1800 T331 LND367 17 REG_GND 3 Q331 0 LND366 16 REG_GND CPH3209-SONY-TL-E C333 LND333 L331 0 135u LND365 15 REG_GND 315V FLASH TRIGGER 0 R335 C331 14 N.C. 0.22u CHARGING

UNIT

LND364 560 CAPACITOR

E LND363 13 N.C. R333 0 Q332 C3340.047u

LND362 12 ST_UNREG 100k MCH3405-TL-E 250V LND361 11 ST_UNREG C338 Cathode 10 ST_UNREG 10uLND360 XE_L LND359 9 ST_UNREG 6.3V D331 Q331,Q332 MA111-(K8).S0 LND332 LND358 8 ST_UNREG TRANS DRIVE R334 LND357 7 ST_UNREG 10k 6 N.C. Q334LND356 CY25BAJ-8F-T23

F LND355 5 XSTRB_PWRSAVE FLASH DRIVE

LND354 4 STRB_ON LND353 3 M_5V R338 LND352 2 N.C. IN VDD 47 LND351 1 STB_FULL OUT

IC331 0GND NC C337 R339XX 1M

FLASH CONTROL IC331 TND721MH5-S-TL-E

G

The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont (Note) Be sure to read “SERVICE NOTE” on page 1-2 line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que when replacing the laser unit (D333). Replace only with part number specified. par une piéce portant le numéro spécifié.

ST-083 4-37 4-38

5412387654321,

COVER 4-2. SCHEMATIC DIAGRAMS SW-395 FLEXIBLE BOARD JK-254, MS-165 FLEXIBLE BOARD For Schematic Diagram For Schematic Diagram

• Refer to page 4-59 for printed wiring board. • Refer to page 4-61 for printed wiring board. 123456123456

SW-395 FLEXIBLE BOARD MS-165 FLEXIBLE BOARD A MIC,LENS ADAPTOR SWITCH(SW BLOCK) A MEMORY STICK CONNECTOR

LND101 1 REG_GND LND102 D101 LND008 8 VSS 10 VSS LND020 2 KEY_AD4 S101 DCZ2805 LND103 LND007 7 VCC 9 VCC LND019 3 IR_LED_A LENS ADAPTOR 2DETECT (IR EMITTER)B 3 (IR) LND018LND104 LND006 6 SCLK 8 SCLK4 IR_LED_A B MEMORY1 LND017 STICK LND105 SY-089 LND005 5 INT 7 N.C.5 IR_LED_K SY-089 (6/12) LND016 (11/12) LND106 LND004 4 DIO 6 INT 6 IR_LED_K CN705 MS D102 MEMORY STICK(PAGE 4-19) LND003 3 N.C. 5 N.C. LND015 CONNECTOR CN753 LND107 7 PANEL_2.9V CL-196HR-CD-T (PAGE 4-30) (SELF TIMER)(RED) LND108 XSELF_TIMER R101 MIC901 LND002 2 BS 4 DIO LND014 8 _LED 470 CN101 2P MICROPHONE LND001 1 VSS 3 N.C. LND013LND109 9 MIC_GND 1 REG_GND 2 BS LND012LND110 10 MIC_SIG 2 MIC_SIG LND111 1 VSS LND011 11 REG_GND

C REG_GND LND112 C

SIGNAL PATH SIGNAL PATH VIDEO SIGNAL

AUDIO

AUDIO Y/CHROMA SIGNAL

SIGNAL REC D

REC D

PB For Schematic Diagram

• Refer to page 4-61 for printed wiring board. 123456

JK-254 FLEXIBLE BOARD A USB,A/V JACK(JK BLOCK)

CN201 5P GND51USB_GND LND201 ID42USB_D+ LND202 D+ 3 3 USB_D- LND203 (USB) D- 2 4 USB_GND LND204

B VCC15USB_JACK_IN LND205

6 STATIC_GND LND206 SY-089 7 STATIC_GND LND207 (9/12) 8 GND_GUARD(REG_GND) LND208 CN752(PAGE 4-26) 9 A_OUT LND209 10 GND_GUARD(REG_GND) LND210 11 AV_JACK_IN LND211 12 GND_GUARD(REG_GND) LND212 J201

C 13 V_OUT LND213A/V OUT

(MONO) 14 REG_GND LND214 LND215 STATIC_GND SIGNAL PATH

D VIDEO SIGNAL AUDIO

Y/CHROMA SIGNAL

REC PB E

4-39 4-40 SW-395, JK-254, MS-165,

COVER 4-2. SCHEMATIC DIAGRAMS BB-004 FLEXIBLE BOARD For Schematic Diagram

• Refer to page 4-62 for printed wiring board. 123456789

BB-004 FLEXIBLE BOARD A SY-DD EXTENSION BOARD B SY-089 DD-195

(12/12) (1/2) CN701 CN082 (PAGE 4-31) (PAGE 4-33) CN401 60P CN402 60P 2 SYS_DD_ON ST_UNREG11ST_UNREG SYS_DD_ON 2

C 4 CLK ST_UNREG33ST_UNREG CLK 4

6 XCS ST_UNREG55ST_UNREG XCS68DATA LANC_5.5V77LANC_5.5V DATA 8 10 REG_GND EVER_3.0V99EVER_3.0V REG_GND 10 12 REG_GND PANEL_2.9V 11 11 PANEL_2.9V REG_GND 12 14 REG_GND CAM_-7.5V 13 13 CAM_-7.5V REG_GND 14 16 REG_GND PANEL_13.5V 15 15 PANEL_13.5V REG_GND 16

D 18 REG_GND CAM_15V 17 17 CAM_15V REG_GND 18

20 REG_GND CAM_15V 19 19 CAM_15V REG_GND 20 22 REG_GND CAM_P_5V 21 21 CAM_P_5V REG_GND 22 24 REG_GND CAM_P_5V 23 23 CAM_P_5V REG_GND 24 26 REG_GND CAM_P_5V 25 25 CAM_P_5V REG_GND 26 28 REG_GND CAM_P_5V 27 27 CAM_P_5V REG_GND 28 30 REG_GND CAM_P_5V 29 29 CAM_P_5V REG_GND 30 32 REG_GND D_1.5V 31 31 D_1.5V REG_GND 32 34 BL_ON D_1.5V 33 33 D_1.5V BL_ON 34

E 36 BL_LEVEL D_1.5V 35 35 D_1.5V BL_LEVEL 36

38 BL_L D_2.9V 37 37 D_2.9V BL_L 38 40 BL_H D_2.9V 39 39 D_2.9V BL_H 40 42 BL_THL D_2.9V 41 41 D_2.9V BL_THL 42 44 BL_THH A_2.9V 43 43 A_2.9V BL_THH 44 46 BATT/XEXT A_2.9V 45 45 A_2.9V BATT/XEXT 46 48 BATT_SIG CAM_3.2V 47 47 CAM_3.2V BATT_SIG 48

F 50 INIT_CHARAGE CAM_3.2V 49 49 CAM_3.2V INIT_CHARAGE 50

52 FAST_CHARGE USB_3.2V 51 51 USB_3.2V FAST_CHARGE 52 54 XRESET_FR USB_3.2V 53 53 USB_3.2V XRESET_FR 54 56 REG_GND ACV_UNREG 55 55 ACV_UNREG REG_GND 56 58 SP+ BATT_UNREG 57 57 BATT_UNREG SP+ 58 60 SP- VL_3V 59 59 VL_3V SP- 60

G H SIGNAL PATH AUDIO SIGNAL I PB BB-004 4-41 4-42

,

COVER 4-2. SCHEMATIC DIAGRAMS FU-165 FLEXIBLE BOARD

For Schematic Diagram • Refer to page 4-63 for printed wiring board. 123456123456

FU-165 FLEXIBLE BOARD CONTROL SWITCH BLOCK(GL-51470) A DC IN,BATTERY IN(FUSE BLOCK) A1 ACV_UNREG1 LND151 CONTROL SWITCH BLOCK (GL-51470) is replaced as a block,

so that PRINTED WIRING BOARD is omited. S254 S258 2 ACV_UNREG1 LND152 3 ACV_UNREG1 LND153 R251 4 ACV_UNREG1 LND154 (RIGHT)/MACRO 3300 DISPLAY/ R254 LCD ON/OFF 3300 5 ACV_UNREG1 LND155 5P LND110 6 ACV_UNREG1 LND156 STATIC_GND S253 S257 7 ACV_UNREG1 LND157

B J101 LND107 ACV_UNREG1 8 ACV_UNREG1 LND158DC IN B

LND109 R252 BATT/XEXT1 9 BATT/XEXT1 LND159 IMAGE SIZE/DELETE R2551500 (LEFT)/REVIEW 1500 LND108 ACV_GND1 10 ACV_GND1 LND160 LND111 11 ACV_GND1 LND161 STATIC_GND S252 S256 12 ACV_GND1 LND162 13 ACV_GND1 LND163 R253 R256 14 ACV_GND1 LND164 (DOWN)/SELF TIMER 1200 (SET) 1200 LND101 15 ACV_GND1 LND165 STATIC_GND

C 16 ACV_GND1 LND166 C S251 S255

17 ACV_GND1 LND167 MENU (UP)/FLASH 18 BATT_GND1 LND168 LND106 SP- 19 SP- LND169 DD-195 SP901 (1/2) SPEAKER LND105 SP+ 20 SP+ LND170 CN081 LND251 1 NC 21 BATT_GND1 LND171 (PAGE 4-33) LND252 2 REG_GND LND112 BT101 VL_3V 22 VL_3V LND172 SY-089 LND253 3 REG_GND

LITHIUM

BATTERY LND113 23 BATT_UNREG1 LND173 (10/12) ACV_GND1 CN703 LND254 4 KEY_AD0

D 24 BATT_UNREG1 LND174 D (PAGE 4-27) LND255 5 KEY_AD1

25 BATT_UNREG1 LND175 LND256 6 KEY_AD2 R257 26 BATT_UNREG1 LND176 S259 R258 S260 R259 S261 1200 1500 3300 27 BATT_UNREG1 LND177 28 BATT_UNREG1 LND178 29 BATT_UNREG1 LND179 EXPOSURE/INDEX FOCUS AE LOCK LND102 BATT_UNREG 30 BATT_UNREG1 LND180 BT901 S LND103BATTERY BATT_SIG 31 BATT_SIG1 LND181 TERMINAL LND104

E BATT_GND 32 BATT_GND1 LND182 E

33 BATT_GND1 LND183 34 BATT_GND1 LND184

SIGNAL PATH 35 BATT_GND1 LND185

36 BATT_GND1 LND186 05

AUDIO 37 BATT_GND1 LND187 SIGNAL 38 BATT_GND1 LND188

39 BATT_GND1 LND189

F PB

The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que Replace only with part number specified. par une piéce portant le numéro spécifié. 4-43 4-44 FU-165, GL-51470,

COVER 4-2. SCHEMATIC DIAGRAMS

12345678910 11 12

CONTROL SWITCH BLOCK (MODE-51470) A

CONTROL SWITCH BLOCK (MODE-51470) is replaced as a block, STATIC_GND so that PRINTED WIRING BOARD is omited. LND100

B

S103 (SHUTTER) (2nd) XSHTR_ON12(1st)

C XAE_LOCK_ON 3 4 ZOOM

R107 S101 1200 S105

D R113 (DOWN) (UP)0

LANC_SIG LND101 REG_GND LND102 HOT LND103 INTELLIGENT CN100 25P D112 INTE_STRB_ON LND104 SHOE NIGHTFRAMING (OFF) NIGHTSHOT 03P4J XAE_LOCK_ON 1 LANC_JACK_IN2 LND105 S102 XSHTR_ON 2 R114 SHOE_GND LND106 REG_GND 3 R108

E LANC_SIG 4 4700R112 0.5%

REG_GND 5 1k R109 R110 HOT 6 6800 3300 C100 INTE_STRB_ON 7 0.01u LANC_JACK_IN2 8 S108R105 SCENE (MODE DIAL) KEY_AD3 9 6800

MANUAL

XPB_ON 1054R115 MODE_DIAL2 11 SET_UP AE-A 1500

F A 3 SY-089 REG_GND 12 MOVIE

(10/12) MODE_DIAL 13 6 10 R116 CN704 (PAGE 4-27) XSETUP_ON 14 PLAY AE-S 1200B 2 XPWR_ON 15 AUTO P_AUTO PWR_LED_ON 16C1R104 D_2.9V 17 1200 XTALLY_LED 18 AE_LOCK_LED 19

G EVER_3.0V 20

XPWR_ON XCHARGE_LED 21 KEY_AD2 22 Program_Dial_B 23 S104 Program_Dial_A 24 POWER NC 25 D105 TLGV1021(T15SOY2,F) R103270 (POWER)(GREEN) D106

H TLRMV1021(T15SOY,F)

R100 (SELF TIMER/RECORDING)(RED) D107 R101 TLGV1021(T15SOY2,F) 470 (AE/AF LOCK)(GREEN) D108 R102 TLYV1021(T15SOY,F) 820 /CHG (ORANGE)

I

DIAL_A

EXECUTE

S106 (JOG DIAL)

J DIAL_B The components identified by mark 0 or dotted Les composants identifiés par une marque 0 sont

line with mark 0 are critical for safety. critiques pour la sécurité. Ne les remplacer que

Replace only with part number specified. par une piéce portant le numéro spécifié. MODE-51470 4-45 4-46

D113 1SS387-TPL3 D101 MAZT082H08S0 D102 MAZT082H08S0 D103 MAZT082H08S0 D104 MAZT082H08S0 D109 MAZT082H08S0 D110 MAZT082H08S0, COVER 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 12213412344334• Circled numbers refer to waveforms. • There are a few cases that the part printed on diagram5433452143211221isn’t mounted in this model. • C: panel designation Pattern Board Name Parts Location Waveforms Total Number of Layers Layers Not Indicated CD-441 Flexible 4-67 – 2 layers – ST-083 Flexible 4-70 – 2 layers – SW-395 Flexible – – 1 layer – JK-254 Flexible – – 2 layers – MS-165 Flexible – – 2 layers – BB-004 Flexible – – 2 layers – FU-165 Flexible – – 2 layers – 4-47,

COVER

4-3. PRINTED WIRING BOARDS Link CD-441 FLEXIBLE BOARD MS-165 FLEXIBLE BOARD ST-083 FLEXIBLE BOARD BB-004 FLEXIBLE BOARD SW-395 FLEXIBLE BOARD FU-165 FLEXIBLE BOARD JK-254 FLEXIBLE BOARD COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CD-441 FLEXIBLE (CCD IMAGER) Note for Printed Wiring Board (See page 4-47).

CD-441 FLEXIBLE BOARD (SIDE A) CD-441 FLEXIBLE BOARD

(SIDE B)

A A

E B Q101

B C B

R103 C103 14 1 R106 C105EBQ102 IC101

C

R110

C C106 15 28 C

C108 R111

BB

C109 1-688-462- 11 1-688-462- 11 05123053214-49 4-50 CD-441 C107 R104 C101 R101 C110 FB101 TH101 LND101 LND102 LND104 LND103 LND106 LND105 LND108 LND107 LND110 LND109 LND112 LND111 LND114 LND113 LND116 LND115 LND118 LND117 LND120 LND119 LND122 LND121 LND124 LND123 LND126 LND125 LND128 LND127 LND130 LND129 LND132 LND131 LND134 LND133 LND136 LND135 LND138 LND137 LND139 +, Printed wiring boards of the SY-089 and DD-195 boards are not shown. Pages from 4-51 to 4-56 are not shown.,

COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS MOUNTED PARTS LOCATION ST-083 FLEXIBLE (FLASH DRIVE, LASER UNIT)

(Note) Be sure to read “SERVICE NOTE” on page 1-2 when replacing the laser unit (D333).

Note for Printed Wiring Board (See page 4-47). ST-083 FLEXIBLE BOARD (SIDE A) ST-083 FLEXIBLE BOARD (SIDE B) A A

C333 C333 FB305 CHARGING

CAPACITOR

2 4

B 5 B

FB302 J301 1 D333 (LASER UNIT) ACC (Note) C331

C1231

R335 CQ332 D333 T331 D

C

5 4 R331 Q331GSAABER334 R33318D332 Q334 R339 LND390K45R338 R337

D 3 D

S30115LND304 LND305 LND3914341IC331 S301 STROBE OPEN DETECT PLUNGER

E E F F G LND332 G

LND331 L33113LND333 1-688-465- 11 1-688-465- 11 051234567057654321FLASH UNIT 4-57 4-58 ST-083 R302 C337 C334 C338 R332 D331 LND351 LND353 LND352 LND355 LND354 LND357 LND356 LND359 LND358 LND361 LND360 LND363 LND362 LND365 LND364 LND367 LND366 LND369 LND368 LND371 LND370 LND374 LND372 LND375 LND373 LND377 LND376 LND379 LND378 LND381 LND380 LND383 LND382 LND385 LND384 LND387 LND386 LND389 LND388 >PI< 5- - 1- -

ST

− +,

COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS SW-395 FLEXIBLE (MIC, LENS ADAPTOR SWITCH)

Note for Printed Wiring Board (See page 4-47). LND101 LND102 LND103 LND105 LND104 LND107 LND106LND108 LND109 LND111 LND110

SW-395 FLEXIBLE BOARD

S101 S101 LENS ADAPTOR

DETECT

LND112 1-688-469- 11 D101 D102 (IR EMITTER) (SELF TIMER) 3 D101 D102

SW-395 4-59 4-60

R101 CN10112> PI < 1-688-469-

S 2 W 1

-395, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS JK-254 FLEXIBLE (USB, A/V JACK) Note for Printed Wiring Board (See page 4-47).

JK-254 FLEXIBLE BOARD (SIDE A) JK-254 FLEXIBLE BOARD (SIDE B) JK-254

8 9 LND201 LND202 LND203 CN201 LND204 LND205 LND206 1 LND207 >PI< LND208LND209 LND210 LND21167LND212 LND213 CN201 LND214 LND215 1-688- (USB) 1-688-466- 11 466- 1 2 BB-004 FLEXIBLE (SY-DD EXTENSION BOARD) A/V OUT Note for Printed Wiring Board (See page 4-47).J201 (MONO) 4 3 BB-004 FLEXIBLE BOARD 05 05 1-688-466- 11 59 60 MS-165 FLEXIBLE (MS CONNECTOR) Note for Printed Wiring Board (See page 4-47). CN402

MS-165 FLEXIBLE BOARD

1 2 1-688-467- 11 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 1-688-468- 11 59 1 CN401 60 2 4-61 4-62 JK-254, MS-165, BB-004 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020, COVER 4-2. SCHEMATIC DIAGRAMS 4-3. PRINTED WIRING BOARDS FU-165 FLEXIBLE (DC IN, BATTERY IN) Note for Printed Wiring Board (See page 4-47). J101 DC IN

FU-165 FLEXIBLE BOARD

1-688-470- 11 39 1 + BT101 SP901 –

SPEAKER

05 BT101 BT901 − S + (LITHIUM BATTERY)BATTERY

TERMINAL

FU-165 4-63 4-64, Waveforms of the SY-089 board are not shown. Page 4-65 and 4-66 are not shown., COVER 4-3. PRINTED WIRING BOARDS 4-5. MOUNTED PARTS LOCATION no mark : side A * mark : side B CD-441 FLEXIBLE BOARD C101 B-1 C107 C-1 C108 C-1 C109 C-3 C110 C-3 FB101 C-3 IC101 C-2 Q101 B-2 Q102 C-1 R101 B-1 R103 B-1 R104 C-1 R106 B-1 R110 C-1 R111 C-1 TH101 C-3 4-67 CD-441, Mounted parts location of the SY-089 and DD-195 boards are not shown. Page 4-68 and 4-69 are not shown., COVER 4-3. PRINTED WIRING BOARDS no mark : side A * mark : side B ST-083 FLEXIBLE BOARD C331 C-6 * C333 A-1 C334 D-6 C338 C-6 D331 D-7 D332 D-6 D333 C-5 FB302 B-3 FB305 B-3 IC331 D-6 J301 B-3 L331 G-3 Q331 C-7 Q332 C-7 Q334 D-6 R302 D-5 R331 C-6 R332 C-7 R333 C-7 R334 C-7 R335 C-7 R337 D-6 R338 D-7 R339 D-7 S301 D-5 T331 C-6

ST-083 44-7-700E

, COVER NOTE 5. REPAIR PARTS LIST NOTE: Characters A to D of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCDCABINET SECTION FRAME BLOCK FRAME BLOCK SECTION-1 SECTION-2 LENS BLOCK SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

BB-004 FLEXIBLE BOARD C FU-165 FLEXIBLE BOARD C ST-083 FLEXIBLE BOARD B CD-441 FLEXIBLE BOARD D JK-254 FLEXIBLE BOARD C SW-395 FLEXIBLE BOARD A, COVER 5. REPAIR PARTS LIST

SECTION 5 REPAIR PARTS LIST

NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant le numéro spécifié. uF: µF • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , uPC... , µPC... , uPD..., µPD... • Abbreviation AUS : Australian model CH : Chinese model CND : Canadian model J : Japanese model JE : Tourist model HK : Hong Kong model KR : Korean model 5-1, COVER 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS 5-1-1. CABINET SECTION ns: not supplied 2 10 MIC901 6 ns 8 ns 9 12 ns 14 2 frame block section-1 1125Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 3-083-400-01 RING, LENS 9 3-083-420-01 STRAP BRACKET CONTROL BOARD (L) 2 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 10 3-083-461-01 WINDOW, LCD (1.5) 3 X-3953-450-1 CABINET (FRONT) ASSY 11 A-7078-692-A SW-395 FLEXIBLE BOARD, COMPLETE 4 3-083-457-01 CASE, MICROPHONE 12 X-3953-451-1 CABINET (REAR) ASSY 5 3-078-890-21 SCREW, TAPPING 13 3-083-416-01 ADHESIVE SHEET (1.5) 6 3-083-419-01 BRACKET, STRAP 14 3-941-343-21 TAPE (A) 7 3-057-082-41 SCREW (M1.7), P2 MIC901 1-542-446-51 MICROPHONE 8 3-083-421-01 STRAP BRACKET CONTROL BOARD (R) 5-2, COVER 5. REPAIR PARTS LIST 5-1-2. FRAME BLOCK SECTION-1 LCD901 60 62 64 63 58 D901 57 65 D333 (Note) 56 55 frame block section-2 54 52 (Note) Be sure to read “PRECAUTIONS FOR USE OF LASER UNIT” on page 1-2 when removing the laser unit and ST-083 flexible board. The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 3-083-455-01 HOLDER, CONDENSER 61 3-083-458-01 SHEET, PROTECTION, MS 52 3-080-222-11 SCREW (M1.7), TAPPING, P2 062 1-477-886-11 SWITCH BLOCK, CONTROL (MODE-51470) 53 3-083-454-01 COVER, SOLENOID 63 1-477-887-11 SWITCH BLOCK, CONTROL (GL-51470) 54 X-3953-452-1 CASE ASSY, ST 64 3-941-343-21 TAPE (A) 55 3-083-453-01 COVER, ASSIST LIGHT 65 3-084-865-01 SHEET (LCD), ADHESIVE 56 3-083-456-01 RETAINER, ASSIST LIGHT COVER 66 3-084-501-01 STOPPER, LCD 057 A-7078-698-A ST-083 FLEXIBLE BOARD, COMPLETE 067 1-477-895-21 FLASH UNIT 58 X-3953-453-1 COVER ASSY, ST 0D333 1-804-947-11 LASER UNIT 59 1-815-853-31 CONNECTOR, MEMORY STICK 0D901 1-477-760-11 BLOCK LIGHT GUIDE PLATE (1.5) 60 1-688-468-11 MS-165 FLEXIBLE BOARD LCD901 8-753-052-52 ACX309AKC-1 5-3, COVER 5. REPAIR PARTS LIST 5-1-3. FRAME BLOCK SECTION-2 ns: not supplied ns ! 104 111 103 113 108 109 102 110 ! BT101 (BATTERY, LITHIUM SECONDARY) Board on the mount position (See page 4-64) lens block section Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 3-083-460-01 SHEET,DD 108 3-083-438-01 LID, BT 102 3-080-222-11 SCREW (M1.7), TAPPING, P2 109 3-083-560-01 FOOT, RUBBER 103 A-7078-694-A DD-195 BOARD, COMPLETE 110 X-3953-454-1 FRAME ASSY 104 A-7078-693-A BB-004 FLEXIBLE BOARD, COMPLETE 111 A-7078-738-A SY-089 BOARD, COMPLETE (SERVICE) 105 A-7078-695-A FU-165 FLEXIBLE BOARD, COMPLETE 112 3-989-735-51 SCREW (M1.7), LOCK ACE, P2 106 3-083-459-01 HOLDER, SPEAKER 113 A-7078-696-A JK-254 FLEXIBLE BOARD, COMPLETE 107 3-989-735-61 SCREW (M1.7), LOCK ACE, P2 5-4, COVER 5. REPAIR PARTS LIST 5-1-4. LENS BLOCK SECTION ns 159 156 161 IC101 (Note) (Note) Be sure to read “Precuations for Replacement of CCD Imager” on page 4-8 when changing the CCD imager. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 151 A-7095-524-A LENS ASSY (B158A) 158 3-083-451-01 SHEET, CCD RADIATION 152 3-083-596-01 SHEET (LE), RADIATION 159 3-083-452-01 HOLDER, LENS 153 1-758-918-11 FILTER BLOCK, OPTICAL 160 3-078-890-21 SCREW, TAPPING 154 3-054-555-01 RUBBER (K), SEAL 161 3-080-222-11 SCREW (M1.7), TAPPING, P2 156 A-7078-697-A CD-441 FLEXIBLE BOARD, COMPLETE IC101 A-7016-847-A CCD BLOCK ASSY 157 3-083-597-01 SHEET (SD), RADIATION 5-5,

BB-004 CD-441

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-7078-693-A BB-004 FLEXIBLE BOARD, COMPLETE ****************************** < CONNECTOR > CN401 1-778-593-21 CONNECTOR, BOARD TO BOARD 60P CN402 1-778-598-21 CONNECTOR, BOARD TO BOARD 60P A-7078-697-A CD-441 FLEXIBLE BOARD, COMPLETE ****************************** (IC101 is not included in this board) < CAPACITOR > C101 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C107 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V C108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C109 1-135-957-91 TANTAL. CHIP 10uF 20% 16V C110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < FERRITE BEAD > FB101 1-414-921-11 FERRITE 0uH < IC > IC101 A-7016-847-A CCD BLOCK ASSY (CCD IMAGER) (Note) < TRANSISTOR > Q101 8-729-037-74 TRANSISTOR UN9213J- (TX).SO Q102 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1) < RESISTOR > R101 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R103 1-216-853-11 METAL CHIP 470K 5% 1/10W R104 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R106 1-216-864-11 METAL CHIP 0 5% 1/10W R110 1-216-819-11 METAL CHIP 680 5% 1/10W R111 1-216-864-11 METAL CHIP 0 5% 1/10W < THERMISTOR > TH101 1-810-816-11 THERMISTOR, NTC (1608)

Electrical parts list of the DD-195 board is

not shown.

Page 5-7 and 5-8 not shown.

(Note) Be sure to read “Precautions for Replacement of CCD Imager” on page 4-8 when changing the CCD imager. 5-6,

FU-165 JK-254 ST-083 SW-395

Ref. No. Part No. Description Ref. No. Part No. Description A-7078-695-A FU-165 FLEXIBLE BOARD, COMPLETE 0Q332 8-729-056-01 TRANSISTOR MCH3405-TL-E ****************************** 0Q334 6-550-656-01 TRANSISTOR CY25BAJ-8F-T23 < BATTERY > < RESISTOR > 0BT101 1-756-191-31 BATTERY, LITHIUM (SECONDARY) R302 1-216-794-11 METAL CHIP 5.6 5% 1/10W BT901 1-694-854-11 BATTERY TERMINAL BOARD R331 1-216-830-11 METAL CHIP 5.6K 5% 1/10W R332 1-216-824-11 METAL CHIP 1.8K 5% 1/10W < JACK > R333 1-216-845-11 METAL CHIP 100K 5% 1/10W R334 1-216-833-11 METAL CHIP 10K 5% 1/10W J101 1-817-331-11 DC JACK 5P R335 1-216-818-11 METAL CHIP 560 5% 1/10W < SPEAKER > R337 1-216-121-11 RES-CHIP 1M 5% 1/10W R338 1-216-805-11 METAL CHIP 47 5% 1/10W SP901 1-529-857-11 SPEAKER (1.6 cm) R339 1-216-857-11 METAL CHIP 1M 5% 1/10W < SWITCH > A-7078-696-A JK-254 FLEXIBLE BOARD, COMPLETE ****************************** S301 1-771-039-11 SWITCH, PUSH (STROBE OPEN DETECT) < CONNECTOR > < TRANSFORMER > CN201 1-816-112-11 CONNECTOR, SQUARE TYPE (USB) 5P (USB) 0T331 1-439-714-21 DC-DC CONVERTER TRANSFORMER < JACK > A-7078-692-A SW-395 FLEXIBLE BOARD, COMPLETE J201 1-569-950-31 JACK (SMALL TYPE) (A/V OUT (MONO)) ******************************* < CONNECTOR > 0 A-7078-698-A ST-083 FLEXIBLE BOARD, COMPLETE ****************************** CN101 1-794-375-21 PIN, CONNECTOR 2P 1-454-674-51 SOLENOID, PLUNGER < DIODE > 0 1-477-895-21 FLASH UNIT 3-083-456-01 RETAINER, ASSIST LIGHT COVER D101 8-719-078-78 DIODE MA6Z718001S0 (IR EMITTER) D102 8-719-077-09 DIODE CL-196HR-CD-T (SELF TIMER) < CAPACITOR > < RESISTOR > C331 1-127-715-91 CERAMIC CHIP 0.22uF 10% 16V 0C333 1-165-943-11 ELECT 135uF 315V R101 1-216-817-11 METAL CHIP 470 5% 1/10W 0C334 1-137-723-21 CERAMIC CHIP 0.047uF 10% 250V C338 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3V < SWITCH > < DIODE > S101 1-762-805-41 SWITCH, PUSH (1 KEY) (LENS ADAPTOR DETECT) 0D331 8-719-073-01 DIODE MA111- (K8).S0 0D332 6-500-237-01 DIODE HAU160C030TP 0D333 1-804-947-11 LASER UNIT (Note) < FERRITE BEAD > Electrical parts list of the SY-089 board is not shown. FB302 1-469-179-21 FERRITE 0uH FB305 1-469-179-21 FERRITE 0uH Pages 5-10 to 5-13 are not shown. < IC > 0 IC331 6-703-635-01 IC TND721MH5-S-TL-E < JACK > J301 1-794-666-31 PIN JACK (4 POLES) (ACC) < COIL > 0L331 1-456-193-11 COIL, TRIGGER < TRANSISTOR > 0Q331 6-550-183-01 TRANSISTOR CPH3209-SONY-TL-E The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. (Note) Be sure to read “SERVICE NOTE” on page 1-2 Replace only with part num- Ne les remplacer que par une pièce when replacing the laser unit (D333). 5-9 ber specified. portant le numéro spécifié.,

Checking supplied accessories.

Power cord (1) AC adaptor NP-FC11 battery pack (1) Hand strap (1) 0 1-696-819-11 (AUS) AC-LS5 (1) 3-083-484-01 0 1-769-608-11 (AEP, E) 0 1-477-730-11 (EXCEPT CH) 0 1-776-985-11 (KR) 0 1-477-730-21 (CH) 0 1-782-476-13 (CH) 0 1-783-374-11 (UK, HK) 0 1-790-107-22 (US, CND) 0 1-790-732-11 (JE, J)

Other accessories

3-082-311-01 MANUAL, INSTRUCTION (for BASIC) (JAPANESE) (J) 3-082-311-11 MANUAL, INSTRUCTION (ENGLISH) (US, CND, AEP, UK, E, AUS, CH, HK, JE) 3-082-311-21 MANUAL, INSTRUCTION (FRENCH, GERMAN) (CND, AEP) USB cable (1) A/V connecting cable (1) 3-082-311-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) 1-827-038-11 1-824-111-11 (AEP, E, JE) 3-082-311-41 MANUAL, INSTRUCTION (ITALIAN, DUTCH) (AEP) 3-082-311-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, CH, HK, JE) 3-082-311-61 MANUAL, INSTRUCTION (RUSSIAN, SWEDISH) (AEP) "Memory Stick" (32MB) (1) CD-ROM 3-082-311-71 MANUAL, INSTRUCTION (ARABIC) (E) (SPVD-010 USB driver) (1) 3-082-311-81 MANUAL, INSTRUCTION (KOREAN) (KR) 3-078-942-03 (EXCEPT US, CND, J) 3-082-312-01 MANUAL, INSTRUCTION (for APPLICATION) 3-078-943-03 (US, CND, J) (JAPANESE) (J) 3-083-500-01 MANUAL, INSTRUCTION (ENGLISH) (US) Conversion Adaptor (1) Conversion Adaptor (1) 0 1-569-008-12 (E) 0 1-569-007-11 (E, JE) Clamp Filter (Ferrite Core) (1) 1-543-798-11 The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. 5-14E,

Sony EMCS Co. 2003E0500-19-876-261-31 ©2003.5

— 70 — Published by DI Customer Center,

Reverse 987626131.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2003.05 Official Release — —]
15

Similar documents

DSC-V1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-V1 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2004. 09 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS RE
DSC-V1 SERVICE MANUAL LEVEL 2 US Model Canadian Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model
DSC-V1 SERVICE MANUAL LEVEL 2 US Model Ver 1.2 2004.10 Canadian Model Revision History AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Korea Model Tourist Model Japanese Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAMS REP
SPECIFICATIONS Camera Power consumption (during shooting with the
DSC-W100 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Brazilian Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIAG
SPECIFICATIONS Camera Power consumption (during shooting with the
DSC-W100 SERVICE MANUAL LEVEL 2 US Model Ver. 1.3 2007.04 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Brazilian Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIA
• Addition of Argentine Model (W1)
DSC-W1/W12 SERVICE MANUAL LEVEL 1 DSC-W1 Ver 1.1 2004.05 US Model Canadian Model Revision History Hong Kong Model Australian Model Argentine Model Chinese Model Brazilian Model Tourist Model Japanese Model DSC-W1/W12 AEP Model UK Model E Model Korea Model Photo: DSC-W1/Silver Link SPECIFICATIONS SEL
• Addition of Argentine Model (W1)
DSC-W1/W12 SERVICE MANUAL LEVEL 1 DSC-W1 Ver 1.2 2004.08 US Model Canadian Model Revision History Hong Kong Model Australian Model Argentine Model Brazilian Model Tourist Model Japanese Model DSC-W1/W12 AEP Model UK Model E Model Chinese Model Korea Model Photo: DSC-W1/Silver Link SPECIFICATIONS SEL
Model information table
DSC-W30/W40 SERVICE MANUAL LEVEL 3 US Model Ver 1.0 2006.01 Canadian Model Revision History AEP Model UK Model E Model How to use Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Tourist Model Photo: DSC
SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger
DSC-W30/W40 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.01 Canadian Model Revision History AEP Model UK Model E Model How to use Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Tourist Model Photo: DSC
SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger
DSC-W30/W40 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2006.07 Canadian Model Revision History AEP Model UK Model E Model How to use Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Tourist Model Photo: DSC
SPECIFICATIONS Camera [Power, general]
DSC-W35 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Brazilian Model Japanese Model Link SPECIFICATIONS BLOCK DI
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-W50 SERVICE MANUAL LEVEL 3 US Model Ver 1.0 2006.01 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: Silver Tourist Model Link SERVICE NOTE PRINTED WIRIN
SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger
DSC-W50 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.01 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIAGR
SPECIFICATIONS Camera [Power, general]
DSC-W55 SERVICE MANUAL LEVEL 2 US Model Ver 1.1 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Brazilian Model Photo: Silver Tourist Model Link SPECIFICAT
SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.0 2005.01 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.1 2005.07 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.2 2005.09 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
TABLE OF CONTENTS
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 3 DSC-W5/W7 Ver 1.0 2005.01 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger
DSC-W70 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-W80HDPR SERVICE MANUAL US Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model
DSC-W80HDPR SERVICE MANUAL US Model Ver. 1.0 2007.03 Canadian Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model [About the service of this model] DSC-W80HDPR is a commondity that packed the Digital Still Camera and Digital Photo Printer Kit. Refer to each following
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-W70 SERVICE MANUAL LEVEL 3 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Tourist Model Photo: Silver Link SERVICE NOTE PRINTED WIRIN
SPECIFICATIONS Camera [Input and Output connectors] Microphone: Monaural
DSC-W80/W85 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Photo: Silver Tourist M
SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-W90 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Photo: Silver Link SPECIFICATIONS BLOCK DI
CAUTION If you have any questions about this product,
MVC-CD350 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Revision History Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD350 COVER SPECIFICATIONS xCamera xAC-L15A/L15B AC Adaptor [System] [Input and
Storage temperature NP-FM50 battery pack Table for difference of functions
MVC-CD200/CD300 SERVICE MANUAL US ModelCanadian Model Level 2 Ver 1.0 2001. 05 AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Tourist Model Korea Model Photo : MVC-CD300 Japanese Model This service manual contains information for japanese model as well. On the SY-67 board
CAUTION WARNING This symbol is intended to alert You are cautioned that any changes or
MVC-CD500 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD500
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model DIGITAL STILL CAMERA
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model Ver 1.0 1998.09 UK Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM CD-206 BOARD CAMERA REC 1 IC431 1,3 78µsec 9.5Vp-p 2 IC431 2,4 µ 9.5Vp-p78 sec 3 IC431 8 1.8Vp-p 78µse
S® Training Manual Digital Camera Sony Mavica Cameras MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01
S® Training Manual Digital Camera Sony Mavica Cameras Models: MVC-FD85 MVC-FD90 MVC-FD95 MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01 Table of Contents Introduction Floppy Disc Drive 41 Common Failures 1 Checking for Floppy Disc Drive Voltage 41 Purpose of this book 1 Checking the
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • C
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model DIGITAL STILL CAMERA
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model SPECIFICATIONS DIGITAL STILL CAMERA • Floppy disk that can be used by the MVC-FD75 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS forma
LCD screen Mass (Approx.) NP-F330 battery pack
MVC-FD87/FD92 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 06 Hong Kong Model Australian Model Korea Model Japanese Model PHoto: MVC-FD92 This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refe