Download: SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger

DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.1 2005.07 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chinese Model Photo: DSC-W5/Silver Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-856-51). • For INSTRUCTION MANUAL, refer to SERVICE MANUAL,...
Author: Tucker Shared: 8/16/19
Downloads: 63 Views: 4106

Content

DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2

DSC-W5/W7

Ver 1.1 2005.07 US ModelCanadian Model

Argentine Model

Revision History Brazilian Model

Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chinese Model Photo: DSC-W5/Silver

Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS

• For ADJUSTMENTS (SECTION 6), refer to SERVICE MANUAL, ADJ (9-876-856-51). • For INSTRUCTION MANUAL, refer to SERVICE MANUAL, LEVEL 1 (9-876-856-41). • This service manual contains information for Japanese model as well. • Reference No. search on printed wiring boards is available. • Table for Differences of Function of Each Model • Note in Lens Frame Installation • Method for Copying or Erasing the Data in Internal Memory. • Exchange Method of Barrier Assy On the CH-168 and SY-001 boards This service manual procides the information that is premised the circuit board replacement service and not intended repair inside the CH-168 and SY-001 boards. Therefore, schematic diagram, printed wiring board and electrical parts list of the CH-168 and SY-001 boards are not shown. The following pages are not shown. DIGITAL STILL CAMERA Schematic diagrams ... Pages 4-11 to 4-30 Printed wiring boards ... Pages 4-39 to 4-42 Waveforms ... Pages 4-45 and 4-46 Mounted parts location ... Pages 4-48 Electrical parts list ... Pages 5-7 and 5-9 to 5-12 The above-described information is shown in service manual Level 3. DSC-W5/W7/W15/W17 2005G0500-1 © 2005.7 9-876-856-31 Sony EMCS Co. Published by DI Technical Support Department,

SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger

[System] A/V OUT (MONO) jack (Monaural) Power requirements Minijack AC 100 to 240 V, 50/60 Hz, Image device DSC-W7/W17: Video: 1 Vp-p, 75 Ω, 3 W 9.11 mm (1/1.8 type) color unbalanced, sync negative CCD, Primary color filter Ω Output voltage AA: DC 1.4V 400 mA × 2Audio: 327 mV (at a 47 k DSC-W5/W15: AAA: DC 1.4 V 160 mA × 2load) 9.04 mm (1/1.8 type) color Output impedance 2.2 kΩ Operating temperature CCD, Primary color filter 0°C to +40°C (+32°F to USB jack mini-B Total pixel number of camera +104°F) DSC-W7/W17: USB communication Storage temperature Approx. 7 410 000 pixels Hi-Speed USB (USB 2.0 −20°C to +60°C (−4°F to DSC-W5/W15: compliant) +140°F) Approx. 5 255 000 pixels [LCD screen] Dimensions Approx. 71×30×91 mm Effective pixel number of camera (2 7/8×1 3/16×3 5/8 inches) DSC-W7/W17: LCD panel 6.2 cm (2.5 type) TFT drive (W/H/D) Approx. 7 201 000 pixels Total number of dots DSC-W5/W15: Mass Approx. 90 g (3 oz)115 200 (480×240) dots Approx. 5 090 000 pixels [Power, general] Design and specifications are subject to change Lens Carl Zeiss Vario-Tessar without notice. 3 zoom lens Power HR 15/51:HR6 (size AA) f = 7.9 - 23.7 mm (38 - 114 mm Nickel-Metal Hydride batteries when converted to a 35 mm still (2), 2.4 V camera) R6 (size AA) Alkaline batteries F2.8 - 5.2 (2, not supplied), 3 V Exposure control Automatic exposure, Manual AC-LS5K AC Acaptor (not exposure, Scene Selection (7 supplied), 4.2 V modes) Power consumption White balance Automatic, Daylight, Cloudy, (during shooting with the LCD screen on) Fluorescent, Incandescent, DSC-W7/W17: 1.2 W Flash DSC-W5/W15: 1.1 W File format (DCF compliant) Operating temperature Still images: Exif Ver. 2.2 0°C to +40°C (+32°F to JPEG compliant, DPOF +104°F) compatible Storage temperature Movies: MPEG1 compliant −20°C to +60°C (−4°F to (Monaural) +140°F) Recording media Internal memory 32 MB Dimensions 91×60×37.1 mm Memor y Stick (3 5/8×2 3/8×1 1/2 inches) Flash Recommended distance (ISO (W/H/D, excluding maximum set to Auto): 0.2 m to 4.5 m protrusions) (7 7/8 inches to 14 feet 9 1/4 Mass Approx. 253 g (8.9 oz) inches) (W)/0.3 m to 2.5 m (including two batterries and (11 7/8 inches to 8 feet 2 1/2 wrist strap) inches) (T) Microphone Electret condenser microphone Speaker Dynamic speaker Exif Print Compatible PRINT Image Matching III Compatible PictBridge Compatible — 2 —, Table for differences of function Model DSC-W5 DSC-W7 DSC-W15 DSC-W17 US, CND, AEP, UK, US, CND, AEP, UK, AEP, UK, AEP, UK Destination E, AUS, HK, CH, E, AUS, HK, CH, E, AUS, HK, CH, E, AUS, HK, KR, AR, BR, J, JE KR, AR, BR, J, JE KR, JE KR, JE CCD imager 5 255 000 pixels 7 410 000 pixels 5 255 000 pixels 7 410 000 pixels Total pixel (Effective pixel) (5 090 000 pixels) (7 201 000pixels) (5 090 000 pixels) (7 201 000pixels) CD board CD-545 CD-546 CD-545 CD-546 Note: DSC-W15/W17 are the same as DSC-W5/W7 • Abbreviation except accessories and packing materials. AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. FLEXIBLE Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page Section Title Page 1. SERVICE NOTE 1-1. Note for Repair ································································ 1-1 1-2. Discharging of The SY-001 Board’s Charging Capacitor (C901) ·············································································· 1-1 1-3. Note in Lens Frame Installation ······································ 1-2 1-4. Description on Self-diagnosis Display ···························· 1-2 1-5. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-3 1-6. Process After Fixing Flash Error ····································· 1-4 2. DISASSEMBLY 2-1. Disassembly ····································································· 2-1 2-2. SY-001 Board Service Position ······································· 2-3 2-3. Exchange Method of Barrier Assy ·································· 2-5 2-3-1.Peel Off Old Ornamental Ring A ···································· 2-5 2-3-2.Remove Old Barrier Assy ················································ 2-6 2-3-3. Install New Barrier Assy ················································· 2-6 2-3-4.Adhere the Ornamental Ring A ······································· 2-7 2-4. Circuit Boards Location ·················································· 2-8 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-3 3-3. Power Block Diagram ····················································· 3-5 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-5 CD-545 FLEXIBLE (CCD IMAGER) ··························· 4-7 CD-545 FLEXIBLE (CCD IMAGER) ··························· 4-9 SW-001 BOARD (CONTROL SWITCH) ···················· 4-31 CONTROL SWITCH BLCOK ····································· 4-32 4-3. Printed Wiring Boards ··················································· 4-35 CD-545 FLEXIBLE ······················································ 4-37 CD-546 FLEXIBLE ······················································ 4-38 SW-001 ········································································· 4-44 4-5. Mounted Parts Location ················································ 4-47 5. REPAIR PARTS LIST 5-1. Exploded Views ······························································· 5-2 5-1-1.Overall Assembly ··························································· 5-2 5-1-2.Cabinet (Front) Block ······················································ 5-3 5-1-3.Main Block Assembly ····················································· 5-4 5-1-4.Lens Block Assembly ······················································ 5-5 5-2. Electrical Parts List ························································· 5-6 — 4 —, 1. SERVICE NOTE 1-1. NOTE FOR REPAIR Make sure that the flat cable and flexible board are not cracked of When remove a connector, don’t pull at wire of connector. bent at the terminal. It is possible that a wire is snapped. Do not insert the cable insufficiently nor crookedly. When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. Cut and remove the part of gilt which comes off at the point. (Be careful or some pieces of gilt may be left inside) 1-2. DISCHARGING OF THE SY-001

BOARD’S CHARGING CAPACITOR

(C901) Discharging the Capacitor The charging capacitor (C901) of SY-001 board is charged up to Short-circuit between the positive and the negative terminals of the maximum 300 V potential. charged capacitor with the short jig about 10 seconds. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the R:1 kΩ/1 W charged voltage which is kept without discharging when the main (Part code: power of the unit is simply turned off. Therefore, the remaining 1-215-869-11) voltage must be discharged as described below. Preparing the Short Jig To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. 1 kΩ/1 W Wrap insulating tape. 1-1, 1-3. NOTE IN LENS FRAME INSTALLATION When tightening a screw, have both sides of the lens block assembly so as not for the load to depend. P2 tapping screw Lens block assembly Lens frame assembly 1-4. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory Stick” or internal “Memory Stick” or internal memory is FORMAT ERROR memory. unformatted. C:13:ss Insert a new “Memory Stick”. “Memory Stick” is broken. MEMORY STICK ERROR Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR E:61: Checking of lens drive circuit. When failed in the focus and zoomss initialization. E:91: Checking of flash unit or replacement Abnormality when flash is being — ss of flash unit. (Note) charged. E:92:ss Insert batteries correctly. Batteries are not inserted correctly. Note: After repair, be sure to perfom “1-6. PROCESS AFTER FIXING FLASH ERROR”. 1-2, 1-5. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note: 1 When replacing the SY-001 board, erase the data in internal memory of the board before replacement. Note: 2 When replacing the SY-001 board or the IC381 on the SY-001 board, execute formatting and initialize the internal memory after

replacement.

Method for Copying the Data in Internal Memory

Copy Copies all images in the internal memory to a “Memory Stick”. OK See the following procedure. Cancel Cancels the copying. 1 Insert a “Memory Stick” having 32 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message “All data in internal memory will be copied Ready?” appears. 3 Select [OK] with v, then z. Copying starts. Copying 102_COPY • Use fully charged Nickel-Metal Hydride batteries or the AC Adaptor (not supplied). If you attempt to copy image files using batteries with little remaining charge, the batteries may run out, causing copying to fail or possibly corrupting the data. • You cannot copy individual images. • The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick” after copying, then execute the [Format] command in Internal Memory Tool). • You cannot select a folder copied on a “Memory Stick”. • A (Print order) mark added to an image is deleted when you copy data.

Method for Formatting the Internal Memory

Format Formats the internal memory. • Note that formatting irrevocably erases all data in the internal memory, including even protected images. OK See the following procedure. Cancel Cancels the formatting. 1 Select [OK] with v on the control button, then press z. The message “All data in internal memory will be erased Ready?” appears. 2 Select [OK] with v, then press z. The format is complete. 1-3, 1-6. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen.

Method for Initializing the Flash Error Code

Initialize Initializes the setting to the default setting. OK See the following procedure. Cancel Cancels the resetting. 1 Select [OK] with v on the control button, then press z. The message “Initialize all settings Ready?” appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. • Make sure that the power is not disconnected during resetting. 1-4E, 2. DISASSEMBLY The following flow chart shows the disassembly procedure. 2-1. DISASSEMBLY R:1 kΩ/1 W (Part code: 1-215-869-11) qa 0 qs 7 99 Note: High-voltage cautions Discharging the Capacitor 1 Short-circuit between the two points with the short jig about 1068seconds. 03386247115211P2 torasuta screw (M1.7) x4 7 Claw x1 2 Claw x1 8 BT side cabinet (C) 1 Screw (M1.7) x2 Cabinet (rear) block assembly Claw x3 6 Connector: CN753392LCD frame Screw (M1.7) x2 SP sheet 7 Control switch block403Terminal guard SW-001 board Connector: CN601 8 Connector x2: CN801, 8025 qa 4 Fuse label 6 Flexible board x2: CN451, 452 qs D901, LCD901 9 Remove the cabinet (front) block. 5 Remove the control switch block. 0 Cabinet (front) block 1 Ornamental ringA21Connector: CN0011 2 Tapping screw x232Battery holder 3 Barrier assy 3 Connector x2: CN201, 40134Lens block Note: When you exchange rings, be sure to follow the procedure carried on 4 "2-3. Exchange Method of Barrier Assy" (2-5 page). 2-1 2-2, 2-2. SY-001 BOARD SERVICE POSITION Connection cord (DK-2AA) (1-830-351-11) Batery holder qa qs AC power AC IN 9 adaptor 1 SW-001 0 Control switch blockFFC-051 3 8647115SY-001 board79A/V cable (Note) 6 8 D901, LCD901 3 (Note) Lens block Color monitor Note: If the A/V cable is connected to the AV OUT (MONO) jack of SY-001 board, the image can not appear on the LCD screen. If you want to confirm the circuit of LCD drive or LCD, disconnect the A/V cable. 2-3 2-4, 2-3. EXCHANGE METHOD OF BARRIER ASSY 2-3-2. REMOVE OLD BARRIER ASSY Service parts 1 Remove two screws. * Discard the removed screws. Part Number Part Name Quantity113-091-427-01 Ring (A), Ornamental12Remove the Barrier Assy. 2 X-3954-476-1 Barrier Assy 1 * Discard the removed Barrier Assy. 3 3-086-156-31 Tapping screw (P2) 2 Tools used Torque driver 2 Soldering iron 1 Weight about 60g Adhesive (Super X) (Note) Note: Use adhesive (Super X) or an equivalent article. Don’t use what becomes white after drying like a quick-drying glue. * After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. 2-3-1. PEEL OFF OLD ORNAMENTAL RING A This is an important part to prevent the dust and light from coming in. * After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel. The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force. Heat four circled portions with the soldering iron. Heating temperature is about 300ºC. Beware of a burn since the entire Ornamental Ring becomes hot. 2-3-3. INSTALL NEW BARRIER ASSY * As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame. 1 Install new Barrier Assy by paying attention to the projection of the Barrier Assy in relation to the position shown in the under figure. Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring. * Take extreme care so as not to damage the coated surface of the group-1 frame. 2 Tighten two screws. In case of difficult peeling, heat the ring again with the soldering iron. * Tightening torque = 0.5 kgf (4.9 N) If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 → 2 → 3 → 4 in the under figure one by one sequentially. * Discard the removed Ornamental Ring A. 4 Projection23Tip122-5 2-6, 2-3-4. ADHERE THE ORNAMENTAL RING A Apply an adhesive to four recesses on the top surface of the Barrier Assy. * Do not apply too much adhesive. (Make quantity of adhesives into the quantity in which a groove hides.) Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted. Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens. Note: Be careful not to give a shock. * After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame. A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only. If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up. Do not put the weight on a black mold part. Notch Adhesive Adhesive Adhesive Projection Adhesive Not gap in full circumference. Completion after 30 minutes. 2-7, 2-4. CIRCUIT BOARDS LOCATION SW-001 SY-001 (including CP201 (CH-168 board)) CD-545 flexible (W5/W15)/ CD-546 flexible (W7/W17) Board Name Function CD-545 flexible CCD IMAGER CD-546 flexible CCD IMAGER CH-168 CCD SIGNAL PROCESS (included in SY-001) SW-001 CONTROL SWITCH SY-001 CAMERA MODULE, CAMERA DSP, CPU, (including CP-201 LENS DRIVE, BURST FLASH, SDRAM, AND FLASH, (CH-168 board)) LCD DRIVE, AUDIO, VIDEO, DC/DC CONVERTER, FLASH DRIVE, CONNECTOR 2-8E, 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM OVERALL BLOCK DIAGRAM (2/2), 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-001 BOARD (1/2) PANEL UNIT CD-545/546 FLEXIBLE BOARD (1/2) CP201

CAMERA MODULE CN601CD-545 : W5/W15 CD-546 : W7/W17 (1/9) D8 D7 B3 A3

R

LENS BLOCK K2 4E8 E7 B4 B5 G LENS IRIS CH-168 BOARD D6 D5 LCD D0 – LCD D7 A5 B6 K3 5B LCD901 (METER) CN201 K5 G4 H4 E6 B4 A7 B7 K1 3 Q103 (1/2) CS, COM 23 17 BUFFER 16 CCD OUT 134 1362422 L5 H2 H1 E9 6 866912 15 ı CA AD00 – CA AD13 J1 J2 M5 LCD HD, LCD VD, LCD CK A9 IC601 J6 B8 C9 24 COLOR 18 21 24 35 J4 K4 M6 D9 A2 LCD DRIVE LCD Q101 27 30 32 K2 K1 (6/9) RGT, PSIG, 2 MONITOR 19 XCS PANEL HCK1, HCK2, REF, 6W25 B10 49 B1 K4 C2 HST, PCG, XSTBY, ı IC101 Q102 POWER SAVE 105 45 CA HD H5 XSAN RST OUT C10 D2 J4 D1 19 37 133 DWN, EN, VCK, VST 11 CCD E2 F2 F1 ı SHUTTER ZOOM FOCUS IRIS IMAGER 66 CA FD SAN1 SO, XSAN1 SCK B9 G2 G1 H2 14 MOTOR MOTOR MOTOR MOTOR 23 46 J5 A10 19 25 RG, H1B, H2B4533 IC101 101 ı 10 2 42 120 22

MMMM247451 CCD SIGNAL MCK TG

PROCESSOR, 99 48 F2 30 28 H1A, H2A9137 TIMING 132 38 XCS FE, XCS TG U22 31 29 V2, V4, V5A, V5B, 6 3 48 D901GENERATOR 124 39 Y25 4 V6, V7A, V7B, V8 W7/W17 W5/W15

BACKLIGHT

FOCUS 34 IC301 CN752 (1/2) CN451 (1/2) CN45254MHz CLKTGO SENSOR 8 W5/W15 V2, V4, V5A, V5B, 30 9 113 109ı V7, V8, V9, V10 ı 84 47 E1 (1/2) BL H BL H 112 11588110 28 12 BL L BL LCAMERA DSP, CPU77312 ı 125 11926 ı 18 118 121 X201 LENS CONTROL,ı 15 W5/W15 W7/W17 67.5MHz23 W7/W17 MODE CONTROL

SW-001 BOARD (1/2)

1 1 (2/9)V1A, V1B, V1, VST, 36 7 1033V3A, V3B V3B, V3A 35 8 13 126ı 40 41 SAN1 SO, XSAN1 SCK5 7 33 10 17 1296632 11 20 VHLD V6 3 XSAN RST OUT 11 27 20 7 BL L VST VHLD 123 42 OVERALL (2/2) 7 5 31 19 11 BLH1VSUB XSAN RST OUT (PAGE 3-4)

W5/ W7/ 26 21 21 19 AF4 W15 W17 U2

Q201 36 135 R6 SAN1 SO, XSAN1 SCK SAN1 SO, XSAN1 SCK 27 VSUB CONT 20 IC802 Q202 VSUB CONT R23 SAN VOUT IC401 H26 4 VIDEO AMP2VLINE OUT U23 VIDEO AMP ON 1 (7/9) LENS DRIVE (3/9) CN401 FC BRK A, K26 SAN AUOUT A6 F MOTOR A, A, B, B 24 FOCUS A, A, B, B B5 FOCUS B7 FC DIR A, SAN AUIN B8 FC DIR B L4 L26 ı MOTOR L2 T23 XAUDIO MUTE27 A4 C7 2 OVERALL (2/2)DRIVER N5 Y26 XCS AUDIOB4 C8 (PAGE 3-3) ZM BRK A, ZM BRK B, AC1 Z DC MOTOR ± 17 ZOOM DC ± C1 ZOOM B3 ZM DIR A N2 AD1 USB DP, USB DMı D2 MOTOR B1 P520 USB DPULLUPDRIVER A2 N6 T5 IRIS M IN, Q301 DPULLUP ON IRIS M EN, G5 G3 IRIS S IN, P4 ZOOM ZOOM IRIS M±, S± 5 IRIS M±, S± H6

IRIS

ı 8 G4 MOTOR H2 IRIS S EN N4 AB6 AC4 FG SENSOR DRIVER G2 P6 AE4 AE5 MS BS, MS D0 – MS D3, MS CLKH4 G1 R2 AC5 AF6 SHUTTER MSHUT DIR, XSAN RST OUT SHUTTER ± 1 SHUTTER± E7 F8 MSHUT EN R25 AB13 AA13 AE13 AF13ı MOTORD7 F7 R5 AF12 AE12 AA12 AC124 CPU D0 – CPU D15DRIVER AC11 AB12 AE11 AF11 AE10 AB11 AC10 AB10 F PI SENS OUT FC SENS AF21 AF20 AE20 AB18 AB19 AC19 AB1629 U4 AE19 AF19 AF18 AE18 AA15 AC18 AC17 CPU A01 – CPU A21, CPU A25 Z PI SENS OUT 21 ZM SENS 1ST V4 AB15 AE17 AF17 AE16 AB14 AC16 AC15 AE14 Z BOX1 PI SENS Col, Z BOX2 PI SENS Col 10 ZM DC FG 1A, 1B V5 13 W4 LENS TEMP LENS TEMP 31 LENS TEMPSENSOR J25 F4 K3 J3 G3 H7 H9 G6 G9 E8 D8 C8 B8 A8 B7 A7 F7 E6 E5 G5 B5 XCPU CS4 F7 E8 D10 D9 C7 A2 B2 C2 A1 B1 C1 E4 G3 E3 G1AC6 K10 H8 H10 G8 G10 D2 D1 D4 B6 A6 C6 B3 G7 F6 F5 F4 IC381 E7 E9 D7 E10 D5 F3 F2 E2 32M AND FLASH IC351 (5/9) 32M BURST FLASH XCPU CS0 (4/9)AE6 E7 T851 AF9 SAN 27M CLKO B4 XE_H D85154ST UNREG 1 D21 D22 D20 B22 A22 A23 R8 N7 R9 N8 P9 M8 B23 E20 E21 B24 A24 A25 M7 L8 L2 M3 M2 P1 FLASH TRIG 300V 3 B25 C25 C26 B26 E10 A10 D10 E11 B10 A11 B11 E12 DSP DQ00 – DSP DQ31, DSP DQM0 – DSP DQM3 N2 R1 N3 R2 E8 D7 UNIT D8 B9 C8 A9 C7 A818STRB CHG R22 D11 D12 F12 B12 A12 E13 A2 C3 A1 C2 B1 D2IC851 XSTRB FULL D13 D14 F13 B15 F14 E14 D3 E2 K9 K1 F8 F27 V23 TRANS DRIVE, D17 D18 D16 B18 A19 G8 G9 F7 F3 G1 XE_L 2 B19 E16 D19 E19 E17FLASH CONTROL, DSP AQ00 – DSP AQ11, DSP QBA0, DSP QBA1 G2 G3 H1 H2 J3 B20 A20 B21 A21 G7 H9 J7 H8 Q851 FLASH CHARGE IC353 DETECT 4 STRB ON DSP QCLKCHARGE+ R4 A18 J1 C901 256M SDRAM + 6 (9/9) STRB CHG CONT CHARGING 5 AB22 A17 DSP QCLKE J2 (4/9)

A : VIDEO SIGNAL CAPACITOR CHARGE- A : AUDIO SIGNAL A : VIDEO/AUDIO SIGNAL 05

3-1 3-2 CPU A20, A21, A25 CPU D0 – CPU D15 CPU A01 – CPU A21 CPU D0 – CPU D15, 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-001 BOARD (2/2)

V LINE OUT CN801 MIC901 B6 MIC SIG 2 SAN AUOUT E5 SAN AUIN IC801 CN802E6 AUDIO AMP A5 SP± 1 SP901 (7/9) A2 2 SPEAKER SAN1 SO, XSAN1 SCK F3E3 XAUDIO MUTE F1 XCS AUDIO E4 XAV JACK IN J751 V LINE OUT AV OUT

OVERALL (1/2) AU LINE OUT (MONO)D1

(PAGE 3-2) 2 CN751 USB DP, USB DM D± 32 DPULLUP ON VCC 1 (USB) CN705 MS BS, MS D0 – MS D3, MS CLK MS BS, DATA0 – DATA3, SCLK ı5 7 MEMORYSTICK

INT CD-545/546 FLEXIBLE BOARD (2/2)

CD-545 : W5/W15 X301 XAV JACK IN CD-546 : W7/W17 12MHz A6 U25 XMS IN CN201 B10 USB VBUS (2/2)C9 A4 XAF LED 39 XAF LED D104 D703 XAE LOCK LED (AE/AF LOCK) F22 SELF TIMER/A9 AF ILLUMINATOR X001 D702 32.768kHz

SW-001 BOARD (2/2) FLASH/ XSTRB LED IC301 A8 IC001

RECORDING E22 (2/2) CN451 CN752 DC/DC (2/2) (2/2) FRONT CONTROL CONVERTER D456 XACCESS LED XACCESS LED (2/9) (8/9)PANEL 8.5V (MS ACCESS) 1 1 E4 EVER 3.0V CN001 S456 – 458, MS VCCV 1 BATT UNREG 454, 460 D 3.1V ı +7 BT901 FUNCTION55KEY AD0 KEY AD0 A 3.1V KEY K23 CAM 2.9V ST UNREG

BATTERY

10 BATT GND − TERMINALD 1.8V ı S451 – 453, 16 455, 459 CAM –7.5V/–8.0V FUNCTION CAM 15V KEY66KEY AD1 KEY AD1 L23 M 5V D 1.2V CAM –0.5V

CONTROL SWITCH BLOCK W7/W17 B8 BT701 LITHIUM

S001 H1 BATTERY(SHUTTER) CN753 K25 BATT SENSXAE LOCK ON XAE LOCK SW G5 9 N21 XSHTR ON XSHUTTER SW T25 MS PWR ON D3 8 P23 W23 XCS DD A6 AA5 C6 MODE 7 MODE DIAL0, 1 MODE DIAL0, 1 L22 AB5 SAN0 SI, SAN0 SO, XSAN0 SCK C5 DIAL 10 L25 Y5 B6 R26 XDD RST OUT A7 Y4 E9 BLH1D001 XPWR LED D23 AA23 XPWR OFF B7 F9 BL L(POWER) 5 OVERALL (1/2) (PAGE 3-2) S002 POWER 1 XPWR ON XPWR ON C7 A : VIDEO SIGNAL

A : AUDIO SIGNAL

05 A : VIDEO/AUDIO SIGNAL 3-3 3-4, 3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-001 BOARD T851

M 5V L603 F001 L851ST UNREG FLASH L601 IC601 PANEL UNIT UNIT CAM 2.9V L604 LCD DRIVE (6/9) LCD901 UNREG CN601 IC851 PANEL 8.5V L602 VDD18 COLOR F003 SUFFIX: TRANS DRIVE, LCD BT901 -12, -22 FLASH CONTROL, M 5V MONITOR BATTERY FLASH CHARGE DETECT(9/9) TERMINAL CN001 L005 SUFFIX: SW-001 BOARD D901LX3 E10 BACKLIGHT + 1 BATT UNREG F002 J1 -11, -21ı UNREG1-1 D002 CN752 CN451 CN452 7 K1 BL HUNREG1-2 VO3 E9 BLH88BLH1BL H 10 J6 BL L UNREG2-1 VL3 F9 BLL77BLL3BL L − BATT GNDı K6 UNREG2-2 16 D 3.1V D4562 2 A1 VO7 K4 PANEL 8.5V (MS ACCESS) PWR1-1 B1 PWR1-2 C2 PWR1-3 D10 PWR2 VO1-1 F1 D 3.1V CONTROL SWITCH BLOCK VO1-2 F2 L001 A 3.1V VL 3V D702 BT701 B8 RTCBAT VFB1 H2 FLASH/ CN753 LITHIUM D001 RECORDING D 3.1V 4 D001 BATTERY (POWER)H1 LDO1 IC351 D703 LDO2IN B3 D 3.1V32M BURST (AE/AF LOCK) 3 D 3.1V LDO2 A3 D 1.8V FLASH (4/9) LDO3IN B2 CP201 LDO3 A2 CAM 2.9V IC381 CAMERA MODULE(1/9) 32M AND FLASH L003 D 1.2V (5/9) CH-168 BOARD LX2 C10 CAM 2.9V L204VFB2 D8 53 IC002 DC CONTROL (8/9) L203 54CAM –0.5V 55 IC001 Q005 71IC353 L202 IC101DC/DC CONVERTER 4 IN– OUT 1 DC CONTROL 256M SDRAM 57 CCD SIGNAL (8/9) 3 IN+ (4/9) L205 PROCESSOR, 56 TIMINGW7/W17 FB204 GENERATOR Q004 49 PWR56OUT1 J7 SWITCHING 4 VEE REG2 3 CAM –7.5V/–8.0V FB203 PWR56OUT2 K7 STB 6 W7/W17 CAM –0.5V 2 VCC REG1 1 CAM 15V 50 LX5-1 J9 LX5-2 J10 IC003 W5/W15 LX5-3 K9 REG LX5-4 K10 (8/9) D003 CD-545/546 FLEXIBLE BOARD VO5 H10 CD-545 : W5/W15 VFB5 H9 CD-546 : W7/W17 CN201 CAM 15V L201 CAM 15V 13 IC101 GT6 H6 FB205CAM –7.5V–8.0V VFB6 H711CCD IMAGER D104 L010 D 3.1V 38 D 3.1V SELF TIMER/D3 MS PWR ON MS PWR IN G1 MS PWR G2 MS VCC MS VCC AF ILLUMINATOR 1 CAM –7.5V : W5/W15 IC401 T25 MS PWR ON CAM –8.0V : W7/W17 Q002, 003 A 3.1V IC301 L008 LENS DRIVE K25 BATT SENS G5 UNREGMON SWITCHING M 5V M 5V (3/9) CN705 FRONT W23 XCS DD A6 CE Q001 VCC MEMORY CONTROL 9 STICK (2/9) AA5 C6 SO BG4 G9 DC CONTROL AB5 SAN0 SI, SAN0 SO, XSAN0 SCK C5 SI IC801 Y5 B6 SCLK TG4 F10 LENS BLOCK R26 XDD RST OUT AUDIO AMP L802 IC802 A7 XRESET PSG4 G8 (7/9) 1 Vout Vdd4A3.1V VIDEO AMP Q401 CN401 Y4 VFB4 F7 (7/9) D 3.1V F PI SENS VccXPWR OFF 28

FZOCOUMS

AA23 B7 XPWROFF SENSORIC804 2.8V REG P25 –7.5V ON (7/9) Z PI SENS Vcc ZOOM XFC RST LED XFC RST LED 23 E5 SENSOR AU 3.1V AU 3.1V Z BOX2 PI D 1.2V D 1.2V 14 SENS Vcc ZOOM D 3.1V L302 9 FGZ BOX1 PI A 3.1V A 3.1V SENS Vcc D 3.1V D 3.1V L301 SD 3.1V SD 3.1V VI 3.1V VI 3.1V 3-5 3-6E EVER 3.0V L006 D 1.2V A 3.1V D 3.1V SD 3.1V L351 D 3.1V, 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM12345678910 11 12 13 14 15 16

A CONTROL BT901 SWITCH BATTERY TERMINAL BLOCK B

Note: Pin name A/B of CN201 A: W5/W15 CN201 39P B: W7/W17 XAF_LED 39 D_3.1V 38

C GND 37

V1A/V1 36 V1B/VST 35 V2 34 V3A/V3B 33

FLASH V3B/V3A 32 UNIT VST/VHLD 31

V4 30 W5/W15

D V5A 29

C901 V5B 28 VHLD/V6 27 CD-545 MIC901 CN801 2P V6/V7 26 1 MIC_GND CHARGING MIC CAPACITOR V7A/V8 25 FLEXIBLE 2 MIC_SIG V7B/V9 24 V8/V10 23

SY-001 BOARD BOARDGND 22 E VSUB 21 (CCD IMAGER)

CN451 8P CN752 8P (1/9) (CAMERA MODULE) VSUB_CONT 20 BL_H88BL_H W7/W17POWER_SAVE 19 BL_L77BL_L (2/9) (CAMERA DSP, CPU) CCD_GND 18 KEY_AD1 6 FFC-051 6 KEY_AD1 (3/9) (LENS DRIVE) NC 17 CD-546 KEY_AD0 5 FLEXIBLE 5 KEY_AD0 CCD_OUT 16 N.C 4 FLAT CABLE 4 N.C. (4/9) (BURST FLASH, SDRAM) GND 15 FLEXIBLEREG_GND33REG_GND

F (5/9) (AND FLASH)

GND 14 LENS BLOCK D_3.1V22D_3.1V CAM_15V 13 BOARD XACCESS_LED11XACCESS_LED (6/9) (LCD DRIVE) GND 12 (7/9) (AUDIO, VIDEO) GND 11 (CCD IMAGER) OVF

SW-001 H1B 10(8/9) (DC/DC CONVERTER) H1A 9 BOARD (9/9) (FLASH DRIVE, CONNECTOR) GND 8CN705 10P H2B 7 G (CONTROL SWITCH)

1 VSS H2A62MS_BS GND53DATA1 MEMORY RG 4

STICK

4 SDIO/DATA0 GND 3 CCD 5 DATA2 GND 2 MEMORY STICK 6 INT CAM_-7.5V/-8.0V17DATA3 CN401 31P 8 SCLK LENS_TEMP 31 9 VCC GND 30

H 10 VSS CP201 F_PI_SENS_OUT 29

F_PI_SENS_VCC 28 F_MOTOR_B 27

PANEL UNIT CH-168 F_MOTOR_A 26

CN601 24P F_MOTOR_B 25 24 COM BOARD F_MOTOR_A 24 23 CS Z_PI_SENS_VCC 23

D901 22 VST CCD SIGNAL GND (Z_PI_SENS) 22I 21 VCK Z_PI_SENS_OUT 21 BACKLIGHT 20 EN PROCESS Z_DC_MOTER_- 2019 DWN Z_DC_MOTER_- 19

18 VDD Z_DC_MOTER_+ 18 LENS FLEXIBLE 17 VSS Z_DC_MOTER_+ 17 16 N.C. GND (Z_BOX2) 16

LCD901 15 VSSG Z_BOX2_PI_SENS_OUT 1514 XSTBY Z_BOX2_PI_SENS_VCC 14 J 2.5 INCH 13 PCG Z_BOX2_PI_SENS_Col 1312 HST Z_BOX1_PI_SENS_OUT 12 COLOR 11 REF GND (Z_BOX1) 1110 TEST1 Z_BOX1_PI_SENS_Col 10

9 N.C. Z_BOX1_PI_SENS_Vcc 9

LCD MONITOR 8 HCK2 IRIS_M_- 8

7 HCK1 BT701 IRIS_M_+ 7

LITHIUM

6 PSIG BATTERY J751 CN751 5P IRIS_S_- 6

K5GAV OUT 5 GND IRIS_S_+ 5

(MONO) 4R4ID SHUTTER_- 43B3D+ SHUTTER_- 3 2 RGT22D- (USB) SHUTTER_+ 2 1 TEST2 1 VCC SHUTTER_+ 1

L

SP901

SPEAKER

4-1 4-2 FRAME CN452 6P 6 N.C. 5 N.C. 4 N.C. 3 BL_L 2 N.C. 1 BL_H CN001 16P BATT_GND 16 BATT_GND 15 BATT_GND 14 BATT_GND 13 BATT_GND 12 BATT_GND 11 CN802 2P BATT_GND 10 1 SP+ NC92SP- NC 8 BATT_UNREG 7 BATT_UNREG 6 BATT_UNREG 5 BATT_UNREG 4 BATT_UNREG 3 BATT_UNREG 2 BATT_UNREG 1 CN753 10P MODE_DIAL1 10 XAE_LOCK_ON 9 XSHTR_ON 8 MODE_DIAL0 7 REG_GND 6 XPWR_LED 5 D_3.1V 4 D_3.1V 3 N.C. 2 XPWR_ON 1, 4-2. SCHEMATIC DIAGRAMS Link CD-545 FLEXIBLE BOARD: W5/W15 (CCD IMAGER) SW-001 BOARD (CONTROL SWITCH) CD-546 FLEXIBLE BOARD: W7/W17 (CCD IMAGER) CONTROL SWITCH BLCOK COMMON NOTE FOR SCHEMATIC DIAGRAMS, 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ

LµiFn. 5k0 V or less are not indicated except for electrolytics Pattern box Color bar chart

and tantalums. Pattern box PTB-450 • Chip resistors are 1/10 W unless otherwise noted. For PTB-450:J-6082-200-A J-6020-250-A kΩ=1000 Ω, MΩ=1000 kΩ. or • Caution when replacing chip parts. Small pattern box For PTB-1450: New parts must be attached after removal of chip. PTB-1450 J-6082-559-AJ-6082-557-A Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. L = About 28 cm(PTB-450)Pattern box • Some chip part will be indicated as follows. L = About 12 cm(PTB-1450) Example C541 L452 22U 10UH TA A 2520

L

Kinds of capacitor Case Size External dimensions (mm) Front of the lens • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. • Parts with ★ differ according to the model/destination. Refer to the mount table for each function. • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name 2. Adjust the distance so that the output waveform of XEDIT → EDIT PB/XREC → PB/REC Fig. a and the Fig. b can be obtain. • 2: non flammable resistor H • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– Line • J : IN/OUT direction of (+,−) B LINE. • C: adjustment for repair. • A: not use circuit • Circled numbers refer to waveforms. B B (Measuring conditions voltage and waveform) A A=B/2 A • Voltages and waveforms are measured between the Fig. a (Video output terminal output waveform) measurement points and ground when camera shoots color bar chart of pattern box. They are reference values Electronic beam and reference waveforms. scanning frame (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input CRT picture frame impedance of VOM used.) Fig.b (Picture on monitor TV) When indicating parts by reference number, please include the board name. Note : The components identified by mark 0 or Note : Les composants identifiés par une marque dotted line with mark 0 are critical for safety. 0 sont critiques pour la sécurité. Replace only with part number specified. Ne les remplacer que par une pièce portant le numéro spécifie. 4-5 Yellow Cyan Green White Magenta Red Blue, For Schematic Diagram • Refer to page 4-37 for printed wiring board. 12345678

CD-545 FLEXIBLE BOARD: W5/W15 Note: CD-545 flexible complete board and IC101 are not supplied, but there are included in CCD block assy. A CCD IMAGER (5M CCD BLOCK) Note: Voltage and Waveform of mounted on CD-545 flexible XX MARK:NO MOUNT board can not be measured, because they are mounted

by the side of the lens. D104 OPY5052 LND101 39 XAF_LED SELF TIMER/ LND102 AF ILLUMINATOR38 D_3.1V

B LND103 37 GND

LND104 36 V1A LND105 35 V1B LND106 34 V2 LND107 33 V3A LND108 32 V3B LND109 31 VST LND110 30 V4

C LND111 29 V5A

LND112 28 V5B LND113 27 VHLD LND114 26 V6 LND115 25 V7A LND116 24 V7B LND117 23 V8 LND118 22 GND

D LND119 21 VSUB C101 XX SY-001 LND120 20 VSUB_CONT

(1/9) LND121 19 POWER_SAVE 16 15 14 13 12 11 10987654321CN201 Q101 LND122 PAGE 4-13 18 CCD_GND DTC144EMT2L of LEVEL3 SWITCHLND123 17 NC R102 R10322k 3900 LND124 16 CCD_OUT R101 LND125 15 GND 82 IC101 LND126 14 GND CCD IMAGER IC101

E LND127 13 CAM_15V ICX455CQZ-13

LND128 12 GND LND129 11 GND LND130 10 H1B C103 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 LND131 9 H1A Q103 XX LND132 8 GND 2SC4250(T5LSONY1)BUFFER LND133 7 H2B LND134 6 H2A R109

F 0LND135 5 GND

LND136 4 RG LND137 3 GND LND138 2 GND LND139 1 CAM_-7.5V Precautions for Replacement of CCD Imager R104 • The CD-545 flexible board mounted as a repair part is not

G 820Q102 equipped with a CCD imager.

DTC144EMT2L C104 C102 C105 0.1u 0.1u 0.1u When replacing this board, remove the CCD imager from theSWITCH 16V 16V 16V old one and mount it onto the new one. R105 3900 • If the CCD imager has been replaced, carry out all the adjustments for the camera section. 05 • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. 4-7 4-8 CD-545 VOUT NC NC V8 GND V7B GND V7A GND V6 VDD VHLD RG V5B C107 0.1u 16V H2B V5A H1B V4 SUB VST CSUB V3B NC V3A VL V2 H1A V1B H2A NC NC V1A, For Schematic Diagram • Refer to page 4-38 for printed wiring board. 12345678

CD-546 FLEXIBLE BOARD: W7/W17 Note: CD-546 flexible complete board and IC101 are not supplied, but there are included in CCD block assy. A CCD IMAGER (7M CCD BLOCK) Note: Voltage and Waveform of mounted on CD-546 flexible XX MARK:NO MOUNT board can not be measured, because they are mounted

by the side of the lens. D104 OPY5052 LND101 39 XAF_LED SELF TIMER/ AF ILLUMINATOR LND102 38 D_3.1V

B LND103 37 GND

LND104 36 V1 LND105 35 VST LND106 34 V2 LND107 33 V3B LND108 32 V3A LND109 31 VHLD LND110 30 V4

C LND111 29 V5A

LND112 28 V5B LND113 27 V6 LND114 26 V7 LND115 25 V8 LND116 24 V9 LND117 23 V10 LND118 22 GND

D LND119 21 VSUB C101 XX SY-001 LND120 20 VSUB_CONT

(1/9) 16 15 14 13 12 11 10987654321LND121 19 POWER_SAVE CN201 LND122 PAGE 4-13 18 CCD_GND Q101DTC144EMT2L of LEVEL3 LND123 17 NC SWITCH LND124 16 CCD_OUT R101 R102 R103 IC101 LND125 15 GND 33 12k 2700 CCD IMAGER LND126 14 GND IC101 ICX489CQZ-13

E LND127 13 CAM_15V

LND128 12 GND LND129 11 GND C103 XX 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32LND130 10 H1B Q103 LND131 9 H1A 2SC4250(T5LSONY1)

BUFFER

LND132 8 GND LND133 7 H2B LND134 6 H2A R109

F 0LND135 5 GND

LND136 4 RG LND137 3 GND LND138 2 GND LND139 1 CAM_-8.0V Precautions for Replacement of CCD Imager R104 • The CD-546 flexible board mounted as a repair part is not

G 1200 equipped with a CCD imager.

Q102 C104 R105 C102 C105 When replacing this board, remove the CCD imager from the DTC144EMT2L XX 1500 0.1u 0.1u SWITCH 16V 16V 16V old one and mount it onto the new one. • If the CCD imager has been replaced, carry out all the adjustments for the camera section. 05 • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. 4-9 4-10 CD-546 VOUT NC NC V10 GND V9 GND V8 GND V7 VDD V6 RG V5B C107 0.1u 16V H2B V5A H1B V4 SUB V3B CSUB V3A H1A VHLD H2A V2 VL VST GND NC NC V1, Schematic diagrams of the CH-168 and SY-001 boards are not shown. Pages from 4-11 to 4-30 are not shown., For Schematic Diagram • Refer to page 4-44 for printed wiring board. 1234561234

SW-001 BOARD CONTROL SWITCH BLOCK A CONTROL SWITCH A CONTROL SWITCH BLOCK is replaced as block, XX MARK:NO MOUNT so that PRINTED WIRING BOARD is omitted.

S455 S459 T (ZOOM) W LND452 R007 R009 R01021STATIC_GND 6800 4700 3300

B 2 1

R456 2200 LND45143BSTATIC_GND R0044322k Twilight S451 11 Beach 10 Snow 9 Candle 8 portrait R012 DISPLAY/ 2200 R455 LCD ON/OFF CN452 6P 12 Landscape 7 Twilight 2200 D901216N.C. BACKLIGHT 5 N.C. 6 MANUAL434N.C. R01422k 3 BL_L 5 P_AUTO R013 2 N.C. C 6800C R452 Soft2200211snap 2 MOVIE 3 PLAY 4 AUTOS456 1 BL_H21(SELF TIMER) 4 3 R006 R0084 3 R0112200 3300 4700 S452

MENU

R457 S001 R454 2200 (SHUTTER) 2200 (1st) 2121CN451 8P

D218BL_H D (2nd)4343

R451 S457 S460 7 BL_L SY-001 2200 (8/9) 436KEY_AD1 (SET) (MACRO) CN752S454215KEY_AD0 THROUGH THEFFC-051 FLEXIBLE (REVIEW) R458 4 N.C. FLAT CABLE312200 PAGE 4-28 S002433REG_GND of LEVEL3 POWER S45342R459 1k 2 D_3.1V IMAGE SIZE/ 2 1 DELETE 1 XACCESS_LED R016R453 20k

E 2200 D456 E4 3 SML-310LTT86

S458 (MS ACCESS) R015 20k (FLASH)

F G SY-001

(9/9) CN753 PAGE 4-29 of LEVEL3 4-31 4-32 SW-001, CONTROL SWITCH BLOCK D451 MAZS068008SO D452 MAZS068008SO D455

XX

D453

XX

LND010 10 MODE_DIAL1 LND009 9 XAE_LOCK_ON LND008 8 XSHTR_ON LND007 7 MODE_DIAL0 LND006 6 REG_GND LND005 5 XPWR_LED LND004 4 D_3.1V LND003 3 D_3.1V D001 LND002 2 N.C. TLYU1002(TPX1,SONY) (POWER) LND001 1 XPWR_ON, 4-3. PRINTED WIRING BOARDS

Link

CD-545 FLEXIBLE BOARD: W5/W15 SW-001 BOARD CD-546 FLEXIBLE BOARD: W7/W17 COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION CIRCUIT BOARDS LOCATION Board Name Function CD-545 FLEXIBLE CCD IMAGER CD-546 FLEXIBLE CCD IMAGER SW-001 CONTROL SWITCH, 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 1221324334654456• Circled numbers refer to waveforms. • There are a few cases that the part printed on diagram543345411221123321isn’t mounted in this model. 3 2 • C: panel designation41Parts Location Pattern Board Name (Shown on Page) Total Number of Layers Layers Not Indicated CD-545 flexible 4-47 2 layers – CD-546 flexible 4-47 2 layers – SW-001 4-49 2 layers – 4-35,

CD-545 FLEXIBLE: W5/W15 CD-546 FLEXIBLE: W7/W17

Note for Printed Wiring Board (See page 4-35). Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder. : Uses unleaded solder.

CD-545 FLEXIBLE BOARD CD-546 FLEXIBLE BOARD D104 D104 SELF TIMER/ SELF TIMER/ AF ILLUMINATOR AF ILLUMINATOR A A Note: CD-545 flexible complete board and IC101 Note: CD-546 flexible complete board and IC101

are not supplied, but there are included in are not supplied, but there are included in

CCD block assy. CCD block assy. B B

CD-545 1-865-829- CD-546 1-865-830- >PI< >PI< A A 16 15 143216 15 143211

IC101 IC101 C C

17 17

Q103EBC103 C103C 18 19 30 31 32 Q103

E B 18 19 30 31 32

C

R103 R103 C101 C101 R102 R102 R101 C107 C105 R101 C107 C105 C104 C104 R104 R104 R105 R105BCEBCE

D Q102 D Q102 E E

1-865-829- 11 1-865-830- 11 39 1 39 1 051205124-37 4-38 CD-545, CD-546 LND101 LND103LND102 LND105LND104LND106 LND107 5M LND109LND108 LND111LND110 LND113LND112 LND115LND114 LND117LND116 LND119LND118

D104

LND121LND120 LND123LND122 LND125LND124 LND127LND126 LND129LND128 LND131LND130 LND133LND132 Q101BCELND135LND134 R109 LND137LND136 LND139LND138 C102 LND101 LND103 LND102 LND105 LND104LND106 LND107 7M LND109 LND108 LND111 LND110 LND113 LND112 LND115 LND114 LND117 LND116 LND119 LND118

D104

LND121 LND120 LND123 LND122 LND125 LND124 LND127 LND126 LND129 LND128 LND131 LND130 R109 LND133 LND132 Q101BCELND135 LND134 LND137 LND136 C102 LND139 LND138, Printed wiring boards of the CH-168 and SW-001 boards are not shown. Pages from 4-39 to 4-42 are not shown., SW-001 Note for Printed Wiring Board (See page 4-35). : Uses unleaded solder.

SW-001 BOARD

1313S459 S455

A2424 S459 S455

R456 W (ZOOM) T

S451 DISPLAY/ LCD ON/OFF

1 3 S45124

B LND451 S452

R451

MENU

1 3 S458 S452 (FLASH) 2413S458

C S454 S4602 4 S457

(REVIEW) (MACRO) 1313(SET)1 3 S454 S457 S460242424

S453

1 3 S456

IMAGE SIZE/ DELETE S456 (SELF TIMER) D42R454 2 4 D456

S453 (MS ACCESS) R45731

D455 D451 1-865-828- 11 21

05124-43 4-44 SW-001 R453 R452 R455 LND452 D452 D453 R4581618R459 CN451 CN452AKD456, Waveforms of the SW-001 board are not shown. Pages 4-45 and 4-46 are not shown., 4-3. PRINTED WIRING BOARDS 4-5. MOUNTED PARTS LOCATION no mark : side A * mark : side B CD-545 FLEXIBLE BOARD CD-546 FLEXIBLE BOARD C101 C-1 C101 C-1 C102 C-1 C102 C-1 C103 C-1 C103 C-1 C104 D-2 C104 D-2 C105 D-2 C105 D-2 C107 D-2 C107 D-2 D104 A-1 D104 A-1 IC101 C-2 IC101 C-2 Q101 D-1 Q101 D-1 Q102 D-1 Q102 D-1 Q103 C-1 Q103 C-1 R101 D-1 R101 D-1 R102 D-1 R102 D-1 R103 C-1 R103 C-1 R104 D-2 R104 D-2 R105 D-2 R105 D-2 R109 C-1 R109 C-1 4-47 CD-545, CD-546, Mounted parts location of the SY-001 board is not shown. Pages 4-48 is not shown., 4-3. PRINTED WIRING BOARDS no mark : side A * mark : side B SW-001 BOARD CN451 B-2 CN452 A-2 D451 D-2 D452 B-1 D453 B-2 D455 D-2 D456 D-2 R451 B-1 R452 B-1 R453 C-1 R454 D-1 R455 B-1 R456 A-1 R457 D-2 R458 D-2 R459 C-2 S451 B-1 S452 B-1 S453 D-1 S454 C-1 S455 A-2 S456 D-1 S457 C-1 S458 C-1 S459 A-1 S460 C-2 4-49E SW-001,

NOTE

5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCDOVERALL ASSEMBLY CABINET (FRONT) BLOCK MAIN BLOCK ASSEMBLY LENS BLOCK ASSEMBLY

Link ELECTRICAL PARTS LIST ACCESSORIES

CD-545 FLEXIBLE BOARD D CD-546 FLEXIBLE BOARD D SW-001 BOARD A, 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant uF: µ le numéro spécifié.F • COILS uH: µH • RESISTORS All resistors are in ohms. METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model HK : Hong Kong model J : Jpanese model JE : Tourist model KR : Korean model 5-1, 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS 5-1-1. OVERALL ASSEMBLY ns: not supplied15LCD901 ns 2 Main block assembly (See page 5-4.) 4 D901 ns 7 Cabinet (front) block (See page 5-3.) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. Ref. No. Part No. Description Ref. No. Part No. Description 1 1-479-037-11 SWITCH BLOCK, CONTROL (SILVER) (W5) 5 2-348-202-01 BLIND SHEET 1 1-479-037-21 SWITCH BLOCK, CONTROL (SILVER) (W7) 6 2-348-201-01 FRAME, LCD 1 1-479-037-31 SWITCH BLOCK, CONTROL (BLACK) 7 2-515-756-21 SCREW (M1.7), TORASUTA, P2 (SILVER) (W5: E, HK, KR, AUS, JE/W15) 7 2-515-756-71 SCREW (M1.7), TORASUTA, P2 (BLACK) 1 1-479-037-41 SWITCH BLOCK, CONTROL (BLACK) (W7) 8 A-1095-193-A CABINET (REAR) BLOCK ASSY (W5: SILVER) 1 1-479-037-51 SWITCH BLOCK, CONTROL (BLACK) (W17) 8 A-1095-276-A CABINET (REAR) BLOCK ASSY (BLACK) 1 1-479-037-61 SWITCH BLOCK, CONTROL (BLACK) 8 A-1095-278-A CABINET (REAR) BLOCK ASSY (W7: SILVER) (W5: CH, J) 9 2-580-522-01 CABINET, BT SIDE (C) (SILVER) 02 2-348-199-01 GUARD, TERMINAL 9 2-580-522-11 CABINET, BT SIDE (C) (BLACK) 3 A-1096-987-A SW-001 BOARD, COMPLETE D901 1-479-015-11 BLOCK, LIGHT GUIDE PLATE (2.5) 4 3-078-889-11 SCREW (M1.7) LCD901 8-753-229-36 ACX336AK-3 5-2, 5. REPAIR PARTS LIST 5-1-2. CABINET (FRONT) BLOCK MIC901 59 57 61 SP901 54 56 67 65 Ref. No. Part No. Description Ref. No. Part No. Description 51 2-348-157-01 RING, LENS (W5/W7: SILVER/W15) 61 2-348-163-01 SCREW, TRIPOD 51 2-348-157-11 RING, LENS (W7: BLACK/W17) 62 X-2024-644-1 BOTTOM ASSY (40), CABINET (SILVER) 52 2-348-158-01 GRIP (40) (W5: SILVER) 62 X-2025-148-1 BOTTOM ASSY (B (40)), CABINET (BLACK) 52 2-348-158-11 GRIP (40) (W5: BLACK/W15) 63 2-348-160-01 INNER HOLDER (FRONT) 52 2-348-293-01 GRIP (50) (W7/W17) 64 2-348-164-01 SHEET (OVF), ADHESIVE 53 2-515-716-01 SHEET, GRIP ADHESIVE 65 2-348-162-01 WINDOW, OVF (SILVER) 54 3-348-998-51 SCREW (M1.4X3.5), TAPPING, PAN 65 2-348-162-11 WINDOW, OVF (BLACK) 55 2-348-156-01 CABINET (FRONT) (W5: SILVER) 66 2-515-756-21 SCREW (M1.7), TORASUTA, P2 (SILVER) 55 2-348-156-11 CABINET (FRONT) (BLACK) 66 2-515-756-71 SCREW (M1.7), TORASUTA, P2 (BLACK) 55 2-348-156-21 CABINET (FRONT) (W7: SILVER) 67 2-348-159-01 RING (40), ORNAMENTAL (W5/W15) 56 2-348-161-01 WINDOW, AF 67 2-348-294-01 RING (50), ORNAMENTAL (SILVER) (W7) 57 2-348-166-01 CUSHION, MICROPHONE 67 2-348-294-11 RING (50), ORNAMENTAL (BLACK) (W7/W17) 58 2-348-185-01 CUSHION, MICROPHONE (B) MIC901 1-542-600-11 MICROPHONE UNIT 59 2-348-198-01 COVER, MIC SP901 1-825-923-21 LOUDSPEAKER (1.3CM) 60 2-108-698-01 SCREW (M1.4) 5-3, 5. REPAIR PARTS LIST 5-1-3. MAIN BLOCK ASSEMBLY ns: not supplied BT901 102 SY-001 ns (Note) (including CP201 ! (CH-168 board) and BT701) BT701 Lens block assembly (See page 5-5.) ! BT701(BATTERY, LITHIUM SECONDARY) Board on the mount position (See page 4-40). 105 C901 Note: Included in SY-001 board (suffix: -11). The components identified by Les composants identifiés par une CAUTION mark 0 or dotted line with marque 0 sont critiques pour la Danger of explosion if battery is incorrectly replaced. mark 0 are critical for safety. sécurité.Replace only with part num- Ne les remplacer que par une pièce Replace only with the same or equivalent type. ber specified. portant le numéro spécifié. Ref. No. Part No. Description Ref. No. Part No. Description 101 A-1096-995-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) 101 A-1097-365-A SY-001 BOARD, COMPLETE (SERVICE) (GP4) (W5: J) (W7: AR, BR, E/W17: E) 101 A-1096-996-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) 101 A-1097-366-A SY-001 BOARD, COMPLETE (SERVICE) (GP5) (W5: US, CND, AUS/W15: AUS) (W7: CH, HK, KR, JE/W17: HK, KR, JE) 101 A-1096-997-A SY-001 BOARD, COMPLETE (SERVICE) (GP1) 0102 1-479-039-11 FLASH UNIT (W7: J) 103 1-963-591-11 CABLE, FLEXIBLE FLAT (FFC-051) 101 A-1096-998-A SY-001 BOARD, COMPLETE (SERVICE) (GP2) 104 2-348-515-01 LABEL, FUSE REPLACEMENT CAUTION (W7: US, CND, AUS/W17: AUS) 101 A-1097-361-A SY-001 BOARD, COMPLETE (SERVICE) (GP3) 0105 X-2024-645-1 HOLDER ASSY (40), JACK (SILVER) (W5: AEP, UK/W15: AEP, UK) 0105 X-2025-151-1 HOLDER ASSY (B (40)), JACK (BLACK) 0BT701 1-528-999-61 BATTERY, LITHIUM SECONDARY 101 A-1097-362-A SY-001 BOARD, COMPLETE (SERVICE) (GP4) 0BT901 1-756-527-11 HOLDER, BATTERY (WITH TERMINAL) (W5: AR, BR, E/W15: E) (W5: SILVER) 101 A-1097-363-A SY-001 BOARD, COMPLETE (SERVICE) (GP5) 0BT901 1-756-527-21 HOLDER, BATTERY (WITH TERMINAL) (BLACK) (W5: CH, HK, KR, JE/W15: CH, HK, KR, JE) 101 A-1097-364-A SY-001 BOARD, COMPLETE (SERVICE) (GP3) 0BT901 1-756-527-31 HOLDER, BATTERY (WITH TERMINAL) (W7: AEP, UK/W17: AEP, UK) (W7: SILVER) 0C901 1-112-169-11 CAP, ELECT 135uF 5-4, 5. REPAIR PARTS LIST 5-1-4. LENS BLOCK ASSEMBLY (including CD-545/546 flexible board and IC101) (Note 2) 156 162 151 155 (Note 1) (Note 1) (Note 1) Note 1: Be sure to read “2-3. Exchange Method of Barrier Assy” on page 2-5 when change Ref. No. 152, 153 and 154. Note 2: Be sure to read “Precuations for Replacement of CCD Imager” on page 4-8 or 4-10 when changing the CCD imager. Ref. No. Part No. Description Ref. No. Part No. Description 151 A-1105-719-A LENS BLOCK ASSY (890C (J1)) 159 3-080-222-01 SCREW (M1.7), TAPPING, P2 152 3-091-427-01 RING (A), ORNAMENTAL (Note 1) 160 3-348-998-61 SCREW (M1.4X4), TAPPING, PAN 153 3-086-156-31 SCREW, TAPPING (P2) (Note 1) 161 A-1087-313-A CCD BLOCK ASSY 154 X-3954-476-1 BARRIER ASSY (Note 1) (including CD-545 flexible board and IC101 155 2-021-317-01 MASK, LPF (CCD IMAGER)) (W5/W15) (Note 2) 161 A-1087-314-A CCD BLOCK ASSY 156 1-788-104-11 OPTICAL FILTER BLOCK (W5/W15) (including CD-546 flexible board and IC101 156 1-788-176-11 OPTICAL FILTERBLOCK (OFB-02-21) (W7/W17) (CCD IMAGER)) (W7/W17) (Note 2) 157 2-021-318-01 SEALGOM 890 162 X-2024-646-1 FRAME ASSY, LENS 158 2-348-196-01 HOLDER, AF 5-5,

CD-545 CD-546

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1087-313-A CCD BLOCK ASSY (W5/W15) R103 1-218-958-11 RES-CHIP 2.7K 5% 1/16W (Not supplied) CD-545 FLEXIBLE BOARD, COMPLETE R104 1-218-954-11 RES-CHIP 1.2K 5% 1/16W ******************************* R105 1-218-955-11 RES-CHIP 1.5K 5% 1/16W (CCD block assy is including CD-545 flexible board and IC101 (CCD imager).) R109 1-218-990-11 SHORT CHIP 0 < CAPACITOR > C102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Electrical parts list of the CH-168 board is C104 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V not shown. C105 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Page 5-7 is not shown. C107 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < DIODE > D104 6-500-505-01 DIODE OPY5052 (SELF TIMER/AF ILLUMINATOR) < IC > IC101 (Not supplied) CCD IMAGER (Note) < TRANSISTOR > Q101 6-550-119-01 TRANSISTOR DTC144EMT2L Q102 6-550-119-01 TRANSISTOR DTC144EMT2L Q103 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1) < RESISTOR > R101 1-218-940-11 RES-CHIP 82 5% 1/16W R102 1-218-969-11 RES-CHIP 22K 5% 1/16W R103 1-218-960-11 RES-CHIP 3.9K 5% 1/16W R104 1-218-952-11 RES-CHIP 820 5% 1/16W R105 1-218-960-11 RES-CHIP 3.9K 5% 1/16W R109 1-218-990-11 SHORT CHIP 0 A-1087-314-A CCD BLOCK ASSY (W7/W17) (Not supplied) CD-546 FLEXIBLE BOARD, COMPLETE ******************************* (CCD block assy is including CD-546 flexible board and IC101 (CCD imager).) < CAPACITOR > C102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C105 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C107 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < DIODE > D104 6-500-505-01 DIODE OPY5052 (SELF TIMER/AF ILLUMINATOR) < IC > IC101 (Not supplied) CCD IMAGER (Note) < TRANSISTOR > Q101 6-550-119-01 TRANSISTOR DTC144EMT2L Q102 6-550-119-01 TRANSISTOR DTC144EMT2L Q103 8-729-050-22 TRANSISTOR 2SC4250 (T5LSONY1) < RESISTOR > R101 1-218-935-11 RES-CHIP 33 5% 1/16W R102 1-218-966-11 RES-CHIP 12K 5% 1/16W Note: Be sure to read “Precautions for Replacement of

DSC-W5/W7/W15/W17 CCD Imager” on page 4-8 or 4-10 when changing

5-6 the CCD imager.,

SW-001

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1096-987-A SW-001 BOARD, COMPLETE *********************** < CONNECTOR > CN451 1-817-549-11 CONNECTOR, FPC (LIF (NON-ZIF)) 8P CN452 1-816-654-31 FFC/FPC CONNECTOR (LIF) 6P < DIODE > D451 8-719-056-54 DIODE MAZS068008SO D452 8-719-056-54 DIODE MAZS068008SO D456 8-719-064-07 DIODE SML-310LTT86 (MS ACCESS) < RESISTOR > R451 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R452 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R453 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R454 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R455 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R456 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R457 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R458 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R459 1-216-821-11 METAL CHIP 1K 5% 1/10W < SWITCH > S451 1-786-157-11 SWITCH, TACTILE (DISPLAY / LCD ON/OFF) S452 1-786-157-11 SWITCH, TACTILE (MENU) S453 1-786-157-11 SWITCH, TACTILE (IMAGE SIZE/DELETE) S454 1-786-157-11 SWITCH, TACTILE (g(REVIEW)) S455 1-786-157-11 SWITCH, TACTILE (T(ZOOM)) S456 1-786-157-11 SWITCH, TACTILE (F(SELF TIMER)) S457 1-786-157-11 SWITCH, TACTILE (a(SET)) S458 1-786-157-11 SWITCH, TACTILE (f(FLASH)) S459 1-786-157-11 SWITCH, TACTILE (W(ZOOM)) S460 1-786-157-11 SWITCH, TACTILE (G(MACRO))

Electrical parts list of the SY-001 board is not

shown.

Pages 5-9 to 5-12 are not shown.

5-8,

Checking supplied accessories.

Battery charger Battery case (1) A/V connecting cable (1) USB cable (1) (BC-CS2A/CS2B) (1) 3-074-757-01 1-824-111-11 1-827-038-11 0 1-477-814-11 (US, CND, JE, J) 0 1-477-814-21 (AEP, UK, E, AR, HK, AUS) 0 1-477-814-31 (KR, CH)

Other accessories

2-586-553-01 INSTRUCTION (READ THIS FIRST) (JAPANESE) (J) 2-586-553-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (EXCEPT AR, KR, CH, J) HR6 (size AA) Ni-MH batteries (2) 2-586-553-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (not supplied) (AEP, CND) 2-586-553-31 INSTRUCTION (READ THIS FIRST) (SPANISH, Power cord (1) 1-769-608-31 (AEP, E) PORTUGUESE) (AEP, E, AR, JE)0 1-782-476-13 (CH) 2-586-553-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH)0 0 1-783-374-12 (UK, HK) (AEP) 0 1-783-952-11 (AR) 0 1-790-107-22 (US, CND) Wrist strap (1) 2-586-553-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL 0 1-790-732-12 (JE, J) 2-050-981-01 (Silver) CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 0 1-823-947-12 (KR) 2-050-981-11 (Black) 2-586-553-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN, 0 1-827-945-12 (AUS) SWEDISH) (AEP) 2-586-553-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) 2-586-553-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) 2-586-553-91 INSTRUCTION (READ THIS FIRST) (POLISH, CZECH) (AEP) Conversion 2P adaptor (1) Conversion 2P adaptor (1) 2-586-555-11 INSTRUCTION (READ THIS FIRST) (HUNGARIAN, 0 1-569-008-21 (E) 0 1-569-007-12 (JE) SLOVAK) (AEP) 2-586-561-01 INSTRUCTION (USER'S GUIDE) (JAPANESE) (J) 2-586-561-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT AR, KR, CH, J) 2-586-561-21 INSTRUCTION (USER'S GUIDE) (FRENCH, ITALIAN) (AEP, CND) 2-586-561-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) CD-ROM 2-586-561-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) Soft carrying case (Cyber-shot application (AEP) (W15/W17 only) (1) software) (1) 2-586-561-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, 2-055-904-01 2-583-852-01 (US, J) SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-583-853-01 (EXCEPT US, J) 2-586-561-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN, SWEDISH) (AEP) 2-586-561-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) 2-586-561-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE) 2-586-561-91 INSTRUCTION (USER'S GUIDE) (POLISH, CZECH) (AEP) 2-586-563-11 INSTRUCTION (USER`S GUIDE) (HUNGARIAN, SLOVAK) (AEP) The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié. 55-193EE,

DSC-W5/W7/W15/W17 LEVEL 2 DSC-W5/W7 SERVICE MANUAL US ModelCanadian ModelArgentine ModelBrazilian Model

Japanese Model

Ver 1.1 2005.07 DSC-W5/W7/W15/W17AEP Model

UK Model E Model Australian Model Hong Kong Model Korea Model Tourist Model

DSC-W5/W7/W15

Chinese Model

SUPPLEMENT-1

File this supplement with the service manual. (PV05-033) • Precaution on Replacing the SY-001 Board 1. SERVICE NOTE 1-7. PRECAUTION ON REPLACING THE SY-001 BOARD When you replace to the repairing board, the written data of repairing board also might be changed to original setting. When the data has changed because of board replaceing etc, check the data setting (VIDEO OUT Default Data, Exif Model Data) is right. If not, rewrite to the right value. VIDEO OUT Default Data Data Page Address NTSC PAL 4F 8D 00 01 4F A2 00 01 Exif Model Data Data Page Address DSC-W5 DSC-W7 DSC-W15 DSC-W17 8F E5 35 37 31 31 8F E6 00 00 35 37 Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8D and A2, and set the VIDEO OUT Dafault Data. 3) Select page: 8F, address: E5 and E6, and set the Exif Model Data. 4) Click [Save] on the SEUS screen. 5) Wait for more than 3 sec. 6) Select page: 80, address: 30, and check that the data is “00”. 7) Select page: 00, address: 01, and set data: 00. DSC-W5/W7/W15/W17 2005G0500-1© 2005.7 9-876-856-81 Sony EMCS Co. Published by DI Technical Support Department, [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once 1. Click the Print button . • To reverse the previous screens (operation) one by one, click 2. Specify a printer, print range, number of copies, and other op- the . tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click the . Application of printing: To set a range to be printed within a page, select the graphic Application to the Service Manual: selection tool and drag on the page to enclose a range to This function allows you to go and back between circuit dia- be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it will be convenient for the voltage check. Finding a text 1. Click the Find button . Moving with link 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool , or graphic selection tool . Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing “Find”. page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.) Moving with bookmark: Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.) Application to the Service Manual: The parts on the drawing pages (block diagrams, circuit dia- grams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display the circuit diagram or printed circuit board diagram succes- “Zoom in/out” sively. • Click the triangle button in the zoom control box to select the Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom- Manual depending on the date of issue. ing in or out. Switching a page • To move to the first page, click the . • To move to the last page, click the . “Rotate” • To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each. • To move to the next page, click the . Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set.,

Reverse 987685632.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2005.01 Official Release — — 1.1 2005.07 Supplement-1 • Precaution on Replacing the SY-001 Board No (S1 PV05-033)]
15

Similar documents

SPECIFICATIONS Camera [Input and Output connectors] BC-CS2A/CS2B Ni-MH battery charger
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 2 DSC-W5/W7 Ver 1.2 2005.09 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
TABLE OF CONTENTS
DSC-W5/W7/W15/W17 SERVICE MANUAL LEVEL 3 DSC-W5/W7 Ver 1.0 2005.01 US ModelCanadian Model Argentine Model Revision History Brazilian Model Japanese Model DSC-W5/W7/W15/W17 AEP Model How to use UK ModelE Model Acrobat Reader Australian ModelHong Kong Model Korea Model Tourist Model DSC-W5/W7/W15 Chin
SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger
DSC-W70 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIAGR
DSC-W80HDPR SERVICE MANUAL US Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model
DSC-W80HDPR SERVICE MANUAL US Model Ver. 1.0 2007.03 Canadian Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model [About the service of this model] DSC-W80HDPR is a commondity that packed the Digital Still Camera and Digital Photo Printer Kit. Refer to each following
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-W70 SERVICE MANUAL LEVEL 3 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Tourist Model Photo: Silver Link SERVICE NOTE PRINTED WIRIN
SPECIFICATIONS Camera [Input and Output connectors] Microphone: Monaural
DSC-W80/W85 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Photo: Silver Tourist M
SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-W90 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Photo: Silver Link SPECIFICATIONS BLOCK DI
CAUTION If you have any questions about this product,
MVC-CD350 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Revision History Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD350 COVER SPECIFICATIONS xCamera xAC-L15A/L15B AC Adaptor [System] [Input and
Storage temperature NP-FM50 battery pack Table for difference of functions
MVC-CD200/CD300 SERVICE MANUAL US ModelCanadian Model Level 2 Ver 1.0 2001. 05 AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Tourist Model Korea Model Photo : MVC-CD300 Japanese Model This service manual contains information for japanese model as well. On the SY-67 board
CAUTION WARNING This symbol is intended to alert You are cautioned that any changes or
MVC-CD500 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD500
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model DIGITAL STILL CAMERA
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model Ver 1.0 1998.09 UK Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM CD-206 BOARD CAMERA REC 1 IC431 1,3 78µsec 9.5Vp-p 2 IC431 2,4 µ 9.5Vp-p78 sec 3 IC431 8 1.8Vp-p 78µse
S® Training Manual Digital Camera Sony Mavica Cameras MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01
S® Training Manual Digital Camera Sony Mavica Cameras Models: MVC-FD85 MVC-FD90 MVC-FD95 MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01 Table of Contents Introduction Floppy Disc Drive 41 Common Failures 1 Checking for Floppy Disc Drive Voltage 41 Purpose of this book 1 Checking the
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • C
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model DIGITAL STILL CAMERA
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model SPECIFICATIONS DIGITAL STILL CAMERA • Floppy disk that can be used by the MVC-FD75 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS forma
LCD screen Mass (Approx.) NP-F330 battery pack
MVC-FD87/FD92 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 06 Hong Kong Model Australian Model Korea Model Japanese Model PHoto: MVC-FD92 This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refe
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC Features • Calibration using a 32 kHz external crystal • Adjustable RC frequency with maximum +/-2% accuracy • Tune RC oscillator at any operating voltage and temperature • Tune RC oscillator to any frequency within specification
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 1981A–AVR–03/05 AVR155: Accessing an I2C LCD Display using the AVR® 2-wire Serial Interface Features • Compatible with Philips' I2C protocol • 2-wire Serial Interface Master Driver for Easy Transmit and Receive Function • Initialization and Use ofa2x1
AVR107: Interfacing AVR serial memories
AVR107: Interfacing AVR serial memories Features • Devices: AT25128A/256A, AT25F1024/2048/4096 • Full Serial Memory Functions Support • Memory Array Burst Read • Page Burst Write • Write Protection Detection • On Going Access Detection • Non-blocking Write Access • Access Status Information 1 Introd
AVR120: Characterization and Calibration of the ADC on an AVR
AVR120: Characterization and Calibration of the ADC on an AVR Features • Understanding Analog to Digital Converter (ADC) characteristics • Measuring parameters describing ADC characteristics • Temperature, frequency and supply voltage dependencies • Compensating for offset and gain error Introductio
AVR001 Conditional Assembly and portability macros
AVR001 Conditional Assembly and portability macros Features • Increased portability • Easier Code Writing • Simplified I/O Register Access • Improved Assembly Status Feedback 1 Introduction This application note describes the Conditional Assembly feature present in the AVR Assembler version 1.74 and
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2527A–AVR–9/02 AVR223: Digital Filters with AVR Features • Implementations of Simple Digital Filters • Coefficient and Data Scaling • Fast Implementation of 2nd Order FIR Filter • Compact Implementation Of 8th Order FIR Filter • Fast Implementation of 2nd
8-bit Microcontroller Application Note AVR040: EMC Design Considerations Scope
8-bit Microcontroller Application Note Rev. 1619C–AVR–01/04 AVR040: EMC Design Considerations Scope This application note covers the most common EMC problems designers encounter when using microcontrollers. It will briefly discuss the various phenomena. The refer- ence literature covers EMC design i
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 2508B–AVR–01/04 AVR182: Zero Cross Detector Features • Interrupt Driven • Modular C Source Code • Size Efficient Code • Accurate and Fast Detection • A Minimum of External Components Introduction One of the many issues with developing modern applicati
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity,
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity, allowing the smaller 20-pin AVR to be LED Drive and a • 16 Key Pushbutton Pad in4x4Matrix • 4 Digit Multiplexed LED Display with used. The circuit diagram is shown in
8-bit Microcontroller Application Note AVR180: External Brown-out Protection
8-bit Microcontroller Application Note Rev. 1051B–AVR–05/02 AVR180: External Brown-out Protection Features • Low-voltage Detector • Prevent Register and EEPROM Corruption • Two Discrete Solutions • Integrated IC Solution • Extreme Low-cost Solution • Extreme Low-power Solution • Formulas for Compone
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 1259D–AVR–04/05 AVR134: Real Time Clock (RTC) using the Asynchronous Timer Features • Real Time Clock with Very Low Power Consumption (4 µA @ 3.3V) • Very Low Cost Solution • Adjustable Prescaler to Adjust Precision • Counts Time, Date, Month, and Year wit
  Wiring Diagram
Wiring Diagram Samsung Electronics 6-1
8-bit Microcntroller Application Note
8-bit Microcntroller Application Note Rev. 2532A–AVR–01/03 AVR243: Matrix Keyboard Decoder Features • 64-key Push-button Keyboard in8x8Matrix • No External Components Required • Wakes Up from Sleep Mode on Keypress • Easily Implemented into Other Applications • Low Power Consumption • Software Conta
  Alignment and Adjustments
Alignment and Adjustments 1. Tuner FM THD Adjustment FMOutput Antenna GND SETSSG FREQ. 98 MHz Terminal Oscilloscope Adjustment FM S.S.G Input point FM DETECTOR COIL Speaker (FM DET) Terminal output Input Output 60 dB Distortion Meter Minumum Distortion (0.4% below) (Figure 1-1) Figure1-1 IF CENTER
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2540A–AVR–07/03 AVR104: Buffered Interrupt Controlled EEPROM Writes Features • Flexible Multi-byte EEPROM Buffer • Power Efficient EEPROM Access • Access Control on Buffers • EEPROM Buffer Rewrite Introduction Many applications use the built-in EEPROM of t