Download: SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger

DSC-W70 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use Acrobat Reader E Model Australian Model Hong Kong Model Internal memory Chinese Model ON BOARD Korea Model Argentine Model Photo: Silver Tourist Model Link SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • Precaution on Replacing the SY-156 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for...
Author: Tucker Shared: 8/19/19
Downloads: 865 Views: 2686

Content

DSC-W70 SERVICE MANUAL LEVEL 2 US Model Ver 1.0 2006.03 Canadian Model

Revision History AEP Model

UK Model

How to use Acrobat Reader E Model

Australian Model Hong Kong Model

Internal memory Chinese Model ON BOARD

Korea Model Argentine Model

Photo: Silver Tourist Model

Link

SPECIFICATIONS BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST DISASSEMBLY SCHEMATIC DIAGRAMS • Precaution on Replacing the SY-156 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-W70_L2 2006C0500-1 © 2006.3 9-876-946-31 Sony EMCS Co. Published by DI Technical Support Department,

SPECIFICATIONS Camera [LCD screen] BC-CSG battery charger

[System] LCD panel 6.2 cm (2.5 type) TFT drive Power requirements Total number of dots AC 100 to 240 V, 50/60 Hz, Image device 7.20 mm (1/2.5 type) color2WCCD, Primary color filter 115 200 (480×240) dots [Power, general] Output voltage DC 4.2 V, 0.25 ATotal pixel number of camera Approx. 7 410 000 pixels Operating temperaturePower Rechargeable battery pack NP- 0 to 40°C (32 to 104°F) Effective pixel number of camera BG1, 3.6 V Approx. 7 201 000 pixels Storage temperatureAC-LS5K AC Adaptor (not –20 to +60°C (–4 to +140°F) Lens Carl Zeiss Vario-Tessar supplied), 4.2 V 3× zoom lens Dimensions Approx. 62 × 24 × 91 mmPower consumption (during shooting with the f = 6.3 – 18.9 mm (38 – (2 1/2 × 31/32 ×3 5/8 inches) LCD screen on) 114 mm when converted to a (W/H/D)1.1 W 35 mm still camera) Mass Approx. 75 g (2.7 oz) F2.8 – 5.2 Operating temperature 0 to 40°C (32 to 104°F) Exposure control Automatic exposure, Scene Rechargeable battery pack NP-BG1 Selection (7 modes) Storage temperature –20 to +60°C (–4 to +140°F) Used battery Lithium-ion battery White balance Automatic, Daylight, Cloudy, Fluorescent, Incandescent, Dimensions 88.9×57.1×22.9 mm Maximum voltage Flash (3 1/2 inches × 2 1/4 inches × DC 4.2 V 29/32 inches) (W/H/D, File format (DCF compliant) Nominal voltage DC 3.6 Vexcluding protrusions) Still images: Exif Ver. 2.21 Capacity 3.6 Wh (960 mAh) JPEG compliant, DPOF Mass Approx. 157 g (5.5 oz) compatible (including NP-BG1 battery Design and specifications are subject to change Movies: MPEG1 compliant pack and wrist strap, etc.) without notice. (Monaural) Microphone Electret condenser microphone Recording media Internal Memory (58 MB) Speaker Dynamic speaker “Memory Stick Duo” Exif Print Compatible Flash Recommended distance (ISO set to Auto): approx. 0.2 m to PRINT Image Matching III 3.7 m (7 7/8 inches to 12 feet Compatible 1 3/4 inches) (W)/approx. PictBridge Compatible 0.3 m to 2.1 m (11 7/8 inches to 6 feet 10 3/4 inches) (T) [Input and Output connectors] Multi connector — 2 —,

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. FLEXIBLE Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page 1. SERVICE NOTE 1-1. Description on Self-diagnosis Display ···························· 1-1 1-2. Process After Fixing Flash Error ····································· 1-1 1-3. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-2 1-4. Precaution on Replacing the SY-156 Board ···················· 1-3 2. DISASSEMBLY 2-1. Disassembly ····································································· 2-2 2-2. Exchange Method of Barrier Assy ·································· 2-6 2-3. Exchange Method of Zoom Motor Unit ·························· 2-9 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-2 3-3. Power Block Diagram ····················································· 3-3 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-3 4-3. Printed Wiring Boards ··················································· 4-17 4-4. Mounted Parts Location ················································ 4-26 5. REPAIR PARTS LIST 5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-6 — 4 —, 1. SERVICE NOTE 1-1. DESCRIPTION ON SELF-DIAGNOSIS DISPLAY Self-diagnosis display • C: ss: ss You can reverse the camera malfunction yourself. (However, contact your Sony dealer or local authorized Sony service facility when you cannot recover from the camera malfunction.) • E: ss: ss Contact your Sony dealer or local authorized Sony service facility. Display Code Countermeasure Cause Caution Display During Error C:32:ss Turn the power off and on again. Trouble with hardware. SYSTEM ERROR Format the “Memory Stick” or internal “Memory Stick” or internal memory is FORMAT ERROR memory. unformatted. C:13:ss Insert a new “Memory Stick”. “Memory Stick” is broken. MEMORY STICK ERROR Turn the power off and on again. Trouble with internal memory. INTERNAL MEMORY ERROR E:61: Checking of lens drive circuit. When failed in the focus and zoomss initialization. — E:91: Checking of flash unit or replacement Abnormality when flash is being ss of flash unit. (Note) charged. Note: After repair, be sure to perform “1-2. PROCESS AFTER FIXING FLASH ERROR”. 1-2. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : ** ) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the Setup screen. Method for Initializing the Flash Error Code Initialize Initializes the setting to the default setting. OK See the following procedure. Cancel Cancels the resetting. 1 Select [OK] with v on the control button, then press z. The message “Initialize all settings Ready?” appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. • Make sure that the power is not disconnected during resetting. 1-1, 1-3. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the Setup screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-156 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-156 board, execute formatting and initialize the internal memory after replacement. Method for Copying the Data in Internal Memory

Copy Copies all images in the internal memory to a “Memory Stick Duo”. OK See the following procedure. Cancel Cancels the copying. 1 Insert a “Memory Stick Duo” having 64 MB or larger capacity. 2 Select [OK] with v on the control button, then press z. The message “All data in internal memory will be copied Ready?” appears. 3 Select [OK] with v, then press z. Copying starts. Copying 102_COPY • Use a fully charged battery pack or the AC Adaptor (not supplied). If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. • You cannot copy individual images. • The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in (Internal Memory Tool). • You cannot select a folder copied on a “Memory Stick Duo”. • Even if you copy data, a (Print order) mark is not copied.

Method for Formatting the Internal Memory

This item does not appear when a “Memory Stick Duo” is inserted in the camera. The default settings are marked with . Format Formats the internal memory. • Note that formatting irrevocably erases all data in the internal memory, including even protected images. OK See the following procedure. Cancel Cancels the formatting. 1 Select [OK] with v on the control button, then press z. The message “All data in internal memory will be erased Ready?” appears. 2 Select [OK] with v, then press z. The format is complete. 1-2, 1-4. PRECAUTION ON REPLACING THE SY-156 BOARD VIDEO OUT Default Data Check When you replace to the repairing board, the written data of repairing board also might be changed to original setting because of broadcast system (NTSC/PAL). When the data has changed because of board replacing etc., check the default data of VIDEO OUT if destination code is right. If not, rewrite to the right value. VIDEO OUT Default Data Data Page Address NTSC PAL 4F 8D 00 01 Writing Method: 1) Select page: 00, address: 01, and set data: 01. 2) Select page: 4F, address: 8D, and set data: 00 (NTSC) or data: 01 (PAL). 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is “00”. 6) Select page: 80, address: 30, and check that the data is “00”. 7) Select page: 00, address: 01, and set data: 00. Initial Language Data Check If the SY-156 board was replaced, initial language setting may be changed. Accordingly, change the following data so as to set same initial language as that of the set distributing in each region. Initial language: Language displayed at the next starting if the setting of Setup menu was reset. It is different from the language setting selectable with the menu. Initial Language Data Page Address Data Language GP2 GP3 GP4 00 Englishzzz04 Spanishzz4F 8C 08 Simplified Chinese z 0B Russian z 0D Korean z Note: GP2 is fixed to English. GP3 is either English, Spanish, or Russian. GP4 is either English, Spanish, Simplified Chinese, or Korean. Writing Method: 1) Select page: 00, address: 01 and set data: 01. 2) Select page: 4F, address: 8C, and set the Initial Language Data. 3) Select page: 40, address: 38, and set data: 00. 4) Click [Save] on the SEUS screen. 5) Select page: 80, address: 34, and check that the data is “00”. 6) Select page: 80, address: 30, and check that the data is “00”. 7) Select page: 00, address: 01, and set data: 00. 8) Turn off the camera. 9) Turn on the camera. Execute “Initialize” of Setup screen. 10) Check the language displayed when the camera starts. 1-3E, 2. DISASSEMBLY

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some • When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside) • When installing a connector, dont’ press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE ST-133 BOARD’S CHARGING CAPACITOR (C901)

The charging capacitor (C901) of the ST-133 board is charged up to the maximum 300 V potential. There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by the charged voltage which is kept without discharging when the main power of the unit is simply turned off. Therefore, the remaining voltage must be discharged as described below.

Preparing the Short Jig

To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Note: High-voltage cautions Wrap insulating tape fully around the leads of the resistor to prevent electrical shock. Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds. 1 kΩ/1 W Wrap insulating tape. R:1 kΩ/1 W (Part code: 1-215-869-11) 2-1,

HELP

2-1. DISASSEMBLY

EXPLODED VIEW HARDWARE LIST

2-1-1. CABINET BLOCK Follow the disassembly in the numerical order given. 1 Cabinet (Front) Block Assy (1-1 to 1-9) 2 Cabinet (Rear) Block Assy (2-1 to 2-6) 2Cabinet (Rear) Block Assy 2-5 (Claw) 2-3 (Claw) 1-6 2-2 (#18) 2-6 1-5 (#18) 2-4 (Claw) 2-1 (#18) 1-1 (#18) 1-8 (Claw) 1-9 (Claw) 1-2 (Claw) 1-4 1-3 (Claw) 1-7 (#18) 1Cabinet (Front) Block Assy Refer to page 2-1 " Discharging of the ST-133 board's charging capacitor (C901) ", when discharging the capacitor. 2-2, 2-1-2. LCD BLOCK Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1 LCD Block (1-1 to 1-5) 2 SW-464 Board (2-1 to 2-6) 3 Cabinet (Upper) Block Assy (3-1 to 3-3) 3-1 (#5) 3Cabinet (Upper) Block Assy 1LCD Block 3-3 3-2 2-3 2-6 2-4 (#5) 1-5 (Claw) 2-2 2-1 (Boss) 2-5 (Claw) SW 1-2-464 1-4 (Claw) 1-1 2SW-464 Board 1-3 (Claw) 2-3, 2-1-3. LENS BLOCK Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1 ST-133 Board (1-1 to 1-7) 2 Lens Unit (2-1 to 2-5) 1-2 (Claw) 1-3 1-5 1-1 ST-134 S 2-4 (#19)T-1 2-133 1-4 CD-604 1-6 (Claw) 1-7 2-2 2-5 1ST-133 Board 2-3 Note 1:When you exchange barrier block 2Lens Unit assembly and ornamental ring (A), be sure to follow the procedure carried on "2-2. Exchange Method of Barrier Assembly" (2-6 page). Note 2:When you exchange zoom motor unit, be sure to follow the procedure carried on "2-3. Exchange Method of Zoom Motor Unit" (2-9 page). 2-4, 2-1-4. BT HOLDER BLOCK Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1 SY-156 Board (1-1 to 1-5) 2 JK-303 Flexible Board (2-1 to 2-4) 3 DC-104 Flexible Board (3-1 to 3-6) 3DC-104 Flexible Board 3-1 (Claw) 3-5 (Claw) DC-104 3-6 1SY-156 Board 1-2 3-4 (Claw) 1-5 3-2 1-3 (Claw) (Claw) HELP SY- 1-4156 3-3 JK-303 1-1 (#5) 2-2 2 JK-303 Flexible Board 2-3 (#18) 2-4 2-1 (#18) 2-5, 2-2. EXCHANGE METHOD OF BARRIER ASSY Service parts Part Number Part Name Quantity112-673-650-01 Ring (A), Ornamental122-673-652-01 Barrier Assy132-673-651-01 Tapping screw (B1.2×4) 2 Tools used Torque driver 2 Soldering iron Weight about 60g Adhesive tape (ornamental ring fixed) (2-677-885-01) 2-2-1. PEEL OFF OLD ORNAMENTAL RING A The Ornamental Ring A has adhered to the Barrier Assy strongly and accordingly, use a soldering iron to weaken the adhesive force. Heat four circled portions with the soldering iron. Heating temperature is about 300ºC. Beware of a burn since the entire Ornamental Ring becomes hot. * As the adhesive force of Ornamental Ring A is considerably large, the forced peeling will damage the group-1 frame. Insert the tip of tweezers, etc. into a notch of the group-1 frame and prize the ring. * Take extreme care so as not to damage the coated surface of the group-1 frame. In case of difficult peeling, heat the ring again with the soldering iron. If this re-heating failed, it may be advisable that the ring be peeled while heating the portions 1 → 2 → 3 → 4 in the under figure one by one sequentially. * Discard the removed Ornamental Ring A. Tip 2-6, 2-2-2. REMOVE OLD BARRIER ASSY 1 Remove two screws. * Discard the removed screws. 2 Remove the Barrier Assy. * Discard the removed Barrier Assy. * After removing the Barrier Assy, if the “G1 Dust-Proof Ring” was removed, it must be returned to the home position. In returning the ring, adjust the location of a projection to the lens direction. This is an important part to prevent the dust and light from coming in. * After removing the Barrier Assy, take extreme care not to drop dust or foreign substances in the lens barrel. 2-2-3. INSTALL NEW BARRIER ASSY 1 Install new Barrier Assy. 2 Tighten two screws. * Tightening torque = 0.5 kgf 2-7, 2-2-4. ADHERE THE ORNAMENTAL RING A Apply an adhesive tape to four recesses on the top surface of the Barrier Assy. Meeting a “notch” of the Ornamental Ring A with a “projection” of the group-1 frame, push the Ornamental Ring A into the group-1 frame. * The projection of the spring for preventing static electricity must be tilted. Put the 60g weight on the Ornamental Ring A so that the Ornamental Ring A does not float up until the adhesive hardens. Note: Be careful not to give a shock. * After the weight was put, no gap must be present in full circumference between Ornamental Ring A and group-1 frame. A gap, if present, causes the crackle sound NG. * The weight must push in the Ornamental Ring A only. If the weight is put on the mold part of the Barrier Assy, the Ornamental Ring A will float up. Do not put the weight on a black mold part. Adhesive tape Adhesive tape Not gap in full circumference. Completion after 30 minutes. 2-8, 2-3. EXCHANGE METHOD OF ZOOM MOTOR UNIT Service parts Part Number Part Name Quantity112-673-648-01 Zoom Motor Unit122-673-649-01 BT2 P1.4×3 B3C 2 Tools used Torque driver 2-3-1. REMOVE OLD ZOOM MOTOR UNIT21Remove two screws. * Discard the removed screws. 2 Remove the Zoom Motor Unit. 3 Remove the Lens Flexible Board. * Discard the removed Zoom Motor Unit. 2-3-2. INSTALL NEW ZOOM MOTOR UNIT 1 Install the Lens Flexible Board in new Zoom Motor Unit. 2 Install new Zoom Motor Unit in the Lens Block. 3 Tighten two screws. * Tightening torque = 0.7 kgf 2-9E,

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. CD radiation cushion Lens cushion (130) LCD frame (130)

HELP

, 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM OVERALL BLOCK DIAGRAM (2/2), 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-156 BOARD (1/2) JK-303 FLEXIBLE

LENS BLOCK CD-604 FLEXIBLE BOARD BOARD(1/2) LENS IRIS CN901 CN102 (METER) CN301 K28R21 IC001 171316 CCD_OUT H10 CA_AD00 - CA_AD13 LCD_D0 - LCD_D7 K39G20 BUFFER B LCD901K1 7 22 LCD_HD, LCD_VD, LCD_CK 2.5 INCH IC002 IC901 J6 CS, COM COLOR CCD A2 CA_HD H5 LCD DRIVE LCDIC301 IMAGER MONITOR CCD SIGNAL CA_FD J5 W25 XCS_ PANEL (5/7) SHUTTER ZOOM FOCUS IRIS A3 B10 RGT, PSIG,PROCESS, HCK1, HCK2, REF, MOTOR MOTOR MOTOR MOTOR H1A, H2A, H1B, H2B TIMING B1 HST, PCG, XSTBY,

MMMMGENERATOR X102 DWN, EN, VCK, VST(1/7) 33.75MHz

RG C1019 8 K4 C1 IC101 (1/2) V1, V2, V3A, V3B, V4, V5A, V5B, V6, V7, V8, V9, V10 CAMERA DSP, B9, A10 A4 CLKTGO E1 LENS CONTROL, D901 FOCUS MODE CONTROL CN101

BACKLIGHT

RESET F2VHLD (2/7) 1 BL_HSENSOR 5 31 D5 6VST BL_L2 34 D6 C2 XCS_FE U223126 39 VSUB C4 IC_101_1_SO, XIC_101_1_SCK VSUB_CONT 27 38 Q301 E7 C1 XIC_101_RST_OUT VSUB_CONT_PRE, Q302 VSUB_CONT_POST XIC_101_RST_OUTAF4 IC401 BL_L D4 XCAM_DR_PS 1 OVERALL (2/2)P21 BL_HLENS DRIVE (PAGE 3-2) (3/7) CN401 IRIS_(+), IRIS_(-) IRIS_ M_± IRISMOTOR IRIS_M_IN, IRIS_M_EN

DRIVER

MS_BS, MS_D0 - MS_D3, MS_CLK MS_BS, MS_D0 - MS_D3, MS_CLK F_MOTOR_A, F_MOTOR_A(-), FOCUS_A, FOCUS_A, FC_DIR_A, FC_DIR_B, F_MOTOR_B, F_MOTOR_B(-) FOCUS_B, FOCUS_B FOCUS FC_BRK_AMOTOR IC_101_1_SO, XIC_101_1_SCK IC_101_1_SO, XIC_101_1_SCK

DRIVER

ZM_DIR_A, Z_DC_MOTOR_(+), Z_DC_MOTOR_(-) ZOOM_DC_± ZOOM ZM_BRK_A, ZM_BRK_B Y26 XCS_AUDIOMOTOR DRIVER L26 IC_101_AUIN IC_101_AUOUT K26 SHUTTER_(+), SHUTTER_(-) SHUTTER_± SHUTTERMOTOR MSHUT_DIR, MSHUT_EN DRIVER IC_101_VOUT IC6023 5 V_LINE_OUT

OVERALL (2/2)

H26 U23 VIDEO_AMP_ON 4 VIDEO AMP (PAGE 3-2) (6/7) ZOOM ZOOM FG RESETSENSOR F_PI_SENS_OUT USB_DP, USB_DM USB_DP, USB_DM26 FC_SENS U4 Z_PI_SENS_OUT 29 ZM_SENS_1ST V4 XIC_101_RST_OUT Z_BOX2_PI_SENS_Col, Z_BOX1_PI_SENS_Col ZM_DC_FG_1A, ZM_DC_FG_1B Y4 LENS TEMP LENS_TEMP R26 XSA_RST_OUT C4 B4 XDD_RST_OUT SENSOR 30 J25 Y25 XIC_101_PRE_OUT F11 AE6 XCPU_CS0 L3 CPU_D00 - CPU_ D15

ST-133 BOARD T001

XE_H D00254ST_UNREG CPU_A20, CPU_ A21 IC202

ST-134 FLEXIBLE BOARD

+ 1 256M SDRAM,XDSP_QCS0 TRIGGER D15 M8 64M SUPER AND FLASH 3 DSP_QCLKE (4/7) UNIT TRIGGER_GND CN001 CN704 A17 M7 STRB_CHARGE STRB_CHG A18 DSP_QCLKC901 15 10 9 14 R22 N7IC001 CHARGING 9 12 XSTRB_FULL 17 XSTRB_FULL V23 CAPACITOR FLASH XE_L CONTROL, DSP_DQ0 - DSP_DQ31, DSP_DQM0 - DSP_DQM3 CHARGE 6 11 I_PEAK 16 STRB_CHG_CONT AB22 Q001 CONTROL FLASH7410 STRB_ON 15 STRB_ON R4

DRIVE

Q701 DSP_AQ0 - DSP_AQ11, DSP_QBA0, DSP_QBA1 D003 MIS-FLASHING D_1.2V SELF-TIMER/ 14 XAF_LED PREVENTIONAF ILLUMINATOR 19 XAF_LED XAF_LED 3 OVERALL (2/2)(PAGE 3-2) SP901 SP± SP± SP+, SP-

SPEAKER OVERALL (2/2) A : VIDEO SIGNAL 4 (PAGE 3-2)MIC_SIG MIC_SIG MIC_SIG A : AUDIO SIGNAL MIC901 21 A : VIDEO/AUDIO SIGNAL

3-1 1, 3, 6 - 12, 1, 2 14 - 16 31, 32, 21, 22 6, 3 16 - 19 8 - 11 12 - 15 20, 21 35, 33, 32, 30 - 22 4, 2, 6, 3 22, 23 F4, F3 B4, B5 D6, E6, D2, B1 G7, H6, G6, G5, K6, K5, J6, J5 B7, C6 H5, H4, G4, F4, E4, D7, H7, D4 D1, E3 - E1, F3 - F1, D5, A6, G3 - G1,

G1, E4 A2, C4, B2 B6, C5 D3, E3 B3, C3 H3 - H1, J1

V5, W4 R5, R25 P5, N2, N6 L4, N5, L2 P4, N4 T4, R23 K5, G4, H4, L5, H2, H1, J1, J2, M5, J4, K4, M6, K2, K1 D21, D22, D20, B22, A22, A23, B23, E20, E21, B24, A24, A25, B25, C25, C26, B26, D17, D18, D16, E10, A10, D10, E11, AB13, AA13, AE13, AF13, AF12, AE12, B18, A19, B19, B10, A11, B11, E12, AA12, AC12, AC11, D8, D7, E16, D19, E19, D11, D12, F12, B12, A12, E13, D13, D14, AB12, AE11, AF11, AB6, AC4, E8, E7, E17, B20, A20, F13, B15, F14, E14 AE10, AB11, AE4, AE5, D6, D5, B21, A21 AC16, AC15 AC10, AB10 AC1, AD1 U2, R6 AC5, AF6 E9, B8, D9 E6, B4

XIC_101_RST_OUT

A9, C9, A2 B3, A3, B4, B5, A5, B6, A7, B7

IC_101_1_SO, XIC_101_1_SCK

B1, K4, C2, D2, J4, D1, E2, F2, F1, H9, G10, H10, F9, E9, D8, C8, F8, E8, M3, E3 L11, K10, K12, J11, G2, G1, H2 G9, G2, G3, G4, D7, C7, F4, E5, D6, C6, E11, D12, D10, C10, G5, H2, H3, H8, F3, E4, D5, C5, M10. L10, L12, K11, J10, J12, H4, J6, F6 K9, J9, M9, L9, K8, J8, E10, D11, D9, C9 M5, L5, K4, J4, M4, L4, K3, J3, F7, F5, J7, J5 6, 10 - 12, 15 - 18, 23 - 26 27, 28 23, 19 - 17, 14 - 11, 6 - 3 2, 1, 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

SY-156 BOARD (2/2)

CN703 MS_BS, MS_D0 - MS_D3, MS_CLK MS_BS, MS_D0 - MS_D3, MS_CLK MEMORY

STICK DUO

XMS_IN 6 IC_101_1_SO, XIC_101_1_SCK IC603 D702 XCS_AUDIO AUDIO AMP SP+, SP- (MS ACCESS) E4 (6/7) 4 OVERALL (1/2) IC_101_AUIN (PAGE 3-1)

OVERALL (1/2) E6 B6 MIC_SIG JK-303 FLEXIBLE BOARD

(PAGE 3-1) 2 IC_101_AUOUT (2/2) E5 D1 CN702 AU_LINE_OUT 11 A_OUT_L 16 V_LINE_OUT V_LINE_OUT 13 V_OUT 20 USB_DP, USB_DM USB_DP, USB_DM USB_DP, USB_DM XIC_101_RST_OUT USB_VBUS 4 USB_VBUS 6 XDD_RST_OUT XAV_JACK_IN 14 XAV_JACK_IN 26 CN001 VL_3V MULTI1 BT001 CONNECTOR

LITHIUM BATTERY CONTOROL SW-464 BOARD 31 BATT/XEXT 19 SW BLOCK RL-065 FLEXIBLE BOARD

(SW110T/SW120TB) CN001 CN002 CN705 ACV_UNREG XACCESS_LED MODE MODE_DIAL0, MODE_DIAL1 MODE_DIAL0, MODE_DIAL1 E4

DIAL

S001, S002, XAV_JACK_IN S004 - S009 U25 KEY_AD0, KEY_AD1 KEY_AD0, KEY_AD1 SW110T: SILVER model FUNCTION IC101KEY SW120TB: BLACK model (2/2) S003 FRONT CONTROL (2/7) D001 N V25 XACV_IN (PLAYBACK)

DC-104 FLEXIBLE BOARD

4 PLAY_SW 6 XPLAY_SW IC102 (2/2) D003 CN701 (2/7) Q102 CHARGE_V + AA26 IC_101_TXD4 3 4D001 BATTERY BH001 BATT_SIG BATT_SIG AE/AF LOCK AB25 IC_101_RXD4 CHARGE 10 S BATTERY DETECT TERMINAL/SELF-TIMER – 6 XAE_LOCK_LED 8 XAE_LOCK_LED F22 IC102 (1/2) (2/7) X101 D002 12MHz USB_VBUS FLASH CHARGING A6 EXTAL61C9 ACV_UNREG XMS_IN /RECORD B10 J001Q001, Q002 DC IN BATT/XEXT 7 XSTRB_LED 9 XSTRB_LED E22 A9 IC001 X001 DC/DC 2 IC103 32.768kHz B8 CONVERTER, 3 A8 RESET H1D002 1 (POWER) 1 XPWR_LED D23 BATTERY (7/7) D004

AUTHENTICATE

(2/7) ST_UNREG S002 EVER_SRAM POWER XDD_RST_OUT3 XPOWER_ON A7 MS_VCC D_3.2V W23 XCS_DD A6 A_3.2V S003 D_1.8V (SHUTTER) IC_101_0_SI, IC_101_0_SO, XIC_101_0_SCK CAM_2.9V XAE_LOCK_SW CAM_-7.5V 17 N21 XSHUTTER_SW CAM_12V18 P23 AA23 XPWR_OFF B7 PANEL_8.5V K25 BATT_SENS D4 M_5V T25 MS_PWR_ON D3 D_1.2V 16 KEY_AD2 H25 E9 BL_H F9 BL_L 1

OVERALL (1/2)

S006 (ZOOM) S005 (PAGE 3-1) T W XPLAY_SW (INDEX) D7XPOWER_ON XAF_LED 3 OVERALL (1/2)C7 A4 (PAGE 3-1)

A : VIDEO SIGNAL A : AUDIO SIGNAL 05 DSC-W70_L2 A : VIDEO/AUDIO SIGNAL

3-2 1, 5 2, 3 11, 12 4, 5 14, 15 F3, E3 A5, A2 K23, L23 L22, L25 AA5, AB5, Y5 6 - 8 C6, C5, B6 2 - 5 11 - 14 32 - 39 6, 8 2 - 5, 7, 8 23, 25 10, 12, 3-3. POWER BLOCK DIAGRAM ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

DC-104 FLEXIBLE SY-156 BOARD ST-134 FLEXIBLE ST-133 BOARD BOARD CN701 CN704 BOARD CN001 T001

LF001 ACV_UNREG F001 ST_UNREG ST_UNREG ST_UNREG L001 D002 FLASH J001 UNIT DC IN F002 UNREG D003 + D003 D_3.2V 18 D_3.2V 13 SELF-TIMER/BATT/XEXT 1 AF ILLUMINATOR IC001 C901 D001 M_5V ST_5V ST_5V CHARGING Q001, Q002 13 8 FLASH CONTROL, CAPACITORCHARGE CONTROL + CHARGE_V BH001 BATTERY S BATT_SIG 10 TERMINAL IC001 – ACV_GND DC/DC J1 UNREG1-1 CONVERTER, JK-303 FLEXIBLE K1 UNREG1-2 RESET L903 BOARD (2/2) LCD901 J6 UNREG2-1 (7/7) CN102

JK-303 FLEXIBLE K6 UNREG2-2 L901 IC901 VDD 7 2.5 INCH BOARD (1/2) LCD DRIVE COLORL904 (5/7) LCD

CN702 A1 PWR1-1 L004 F003 MONITOR 19 BATT/XEXT B1 PWR1-2 LX3 E10 CN001 31 D901C2 PWR1-3 CN901 MULTI D005 PANEL_8.5V BACKLIGHT CONNECTOR ACV_UNREG D10 PWR2 22 CN101 VO3 E9 BL_H BL_H16BL_L VL_3V VL3 F9 BL_L31BT001 1 B8 RTCBAT LITHIUM D004 VO1-1 F1 D_3.2V BATTERY H1 LDO1 VO1-2 F2 M_5V IC601 2.9V REG(6/7) IC603VFB1 H2 L003 AUDIO AMP LENS BLOCKAU_3.0V

RL-065 FLEXIBLE 4 VIN VOUT 3 (6/7)

CN401 Z_BOX1_PI_SENS_VCC

SW-464 BOARD BOARD 1 Z_BOX1

LDO2IN B3 2 D001 S002 CN705 LDO2 A3 D_1.8V D601 ZOOM AE/AF LOCK POWER 3 XPOWER_ON

FG

C7 XPWRON1 IC602 4 Z_BOX2_PI_SENS_VCC/SELF-TIMER VIDEO AMP XZM_FG_LED Z_BOX2LDO3IN B2 5 CN002 CAM_2.9V (6/7) 1 D_3.2V 2 D_3.2V LDO3 A2 L002 28 Z_PI_SENS_VCC ZOOM D002 LX2 C10 D_1.2V XZM_RST_LED 27 XZM_RST_LED

RESET

D002 (POWER) SENSOR FLASH CHARGING VFB2 D8 /RECORD Q004, Q005 L001 L006 F_PI_SENS_VCC G2 MS_PWR MS_PWR_IN G1 SWITCHING M_5V IC401 25 FOCUSXFC_RST_LED XFC_RST_LED RESET D3 MS_PWR_ON D_3.2V LENS DRIVE 24 SENSOR Q003 (3/7) D702 BG4 G9 DC CONTROL (MS ACCESS) D_3.2V TG4 F10 D_3.2V CN703 PSG4 G8 CAM_2.9V L303 MEMORY MS_VCC VFB4 F7 STICK 9 D_3.2V L304DUO L305 IC301 FB309 CCD SIGNALPROCESS, Q006 Q007, Q008 TIMING CAM_-7.5V FB307 GENERATORSWITCHING B- SWITCH (1/7) B+ SWITCH CAM_12V FB308 GT6 H6 V25 PH[2] PJ[0] T25 MS_PWR_ONQ102 VFB6 H7 IC002 BATTERY VREF6 G6 8.5V REG (7/7) CHARGE D008 DETECT BATT_SENS L007 AN[4] K25 D4 DTG1 PWR56OUT1 J7 6 Vin Vout 4 AB25 RXD4 IC_101_0_SI, IC_101_0_SO, PWR56OUT2 K7 1 Vcont SCKO XIC_101_0_SCK SCLK LX5-1 J9 TXDO SI CD-604 FLEXIBLE BOARD43AA26 TXD4 LX5-2 J10RXDO SO IC102 PG[7] W23 XCS_DD LX5-3 K9 A6 CE FB301 CN301 (2/7) RST R26 XDD_RST_OUT LX5-4 K10 A7 XRESET 36 CAM_-7.5VVFB5 H9 IC002 RSTA Y4 L301 XPWR_OFF 12 CAM_12V CCD IMAGERPG[0] AA23 B7 XPWROFF PORTB C4 DACK/PI[3] P25 -7.5VON IC001 LED0 B3 XZM_RST_LED LED1 E5 XFC_RST_LED BUFFER LED2 D4 XZM_FG_LEDIC101 CAMERA DSP, D_1.2V IC103 LENS L102 BATTERYCONTROL, AUTHENTICATE MODE (2/7) CONTROL, A_3.2V

FRONT

CONTROL AU_3.0V IC202 (2/7) D_3.2V 256M SDRAM, L101 L201 64M SUPER AND VIDEO_VCC L601 (4/7) SDRAM_VCC 3-3E 23, 25 32 - 39 6 - 9 11 - 14 2 - 5 D_3.2V FB107 BATT_SIG XACV_IN AA5, AB5, Y5 EVER_SRAM C6, C5, B6 D_1.2V D_1.8V A_3.2V AU_3.0V D_3.2V -7.5VON 1 - 5 1 -3, 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM BH001

BATTERY TERMINAL

1 3 23 1

DC-104 FLEXIBLE BOARD

MIC901 J001 MICROPHONEBLOCK DC IN SP901

ST-134 FLEXIBLE BOARD SPEAKER

1411

LEVEL3 LEVEL3 SY-156 BOARD SY-156 BOARD C901CHARGING

(SIDE A) (SIDE B) CAPACITOR 1 19 19 1 23 1 CN705 CN701 CN704 18 2 RL-065 14 1 22 2 CD-604 FLEXIBLE BOARD FLEXIBLE ST-133 BOARD 39 BOARD (SIDE B) 1 CN001 14 1 10

FLASH UNIT

CN703 MEMORY STICK

CONNECTOR

1 12 IC202 12 (Not supplied)11

LENS BLOCK SW-464 BOARD

(SIDE A)

SW-464 BOARD

(SIDE B) CONTROLSW BLOCK CN002 12 1 SW110T/ SW120TB

JK-303 FLEXIBLE BOARD BT001

LITHIUM BATTERY CN00161CN101 39 D901 26 2 BACKLIGHT 1 24 CN102 25 1 28 27 LCD901 CN001 MULTI CONNECTOR 2.5 INCH

COLOR

LCD MONITOR 4-1 FRAME 39 1 29 1 CN702 CN901 38 2 282134516230 2 38 CN401 CN301 1 31 1 39 +, 4-2. SCHEMATIC DIAGRAMS Link CD-604 FLEXIBLE BOARD (CCD IMAGER) RL-065 FLEXIBLE BOARD (CONTROL SWITCH) ST-133 BOARD (FLASH DRIVE) CONTROL SW BLOCK (SW110T/SW120TB) ST-134 FLEXIBLE BOARD JK-303 FLEXIBLE BOARD (MULTI/LCD CONNECTOR) SW-464 BOARD (CONTROL SWITCH) DC-104 FLEXIBLE BOARD (BATTERY IN, DC IN) COMMON NOTE FOR SCHEMATIC DIAGRAMS, 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS

THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS

(In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ µ Pattern boxF. 50 V or less are not indicated except for electrolytics Color bar chart and tantalums. Pattern box PTB-450 For PTB-450: • Chip resistors are 1/10 W unless otherwise noted. J-6082-200-A J-6020-250-A kΩ Ω or=1000 , MΩ=1000 kΩ. Small pattern box For PTB-1450: • Caution when replacing chip parts. PTB-1450 J-6082-559-A New parts must be attached after removal of chip. J-6082-557-A Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. L = 30 cm (PTB-450) • Some chip part will be indicated as follows. L = 12 cm (PTB-1450) Example C541 L452 22U 10UH Pattern box Front of the lens TA A 2520 L Camera Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. 2. Adjust the distance so that the output waveform of • Parts with ★ differ according to the model/destination. Fig. a and the Fig. b can be obtain. Refer to the mount table for each function. H • All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– LineABA=BBA• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform) • C: adjustment for repair. • A: not use circuit Electronic beam (Measuring conditions voltage and waveform) scanning frame • Voltages and waveforms are measured between the measurement points and ground when camera shoots CRT picture frame color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Fig.b (Picture on monitor TV) Precautions for Replacement of Imager When indicating parts by reference number, please • If the imager has been replaced, carry out all the adjustments include the board name. for the camera section. The components identified by mark 0 or dotted line with • As the imager may be damaged by static electricity from mark 0 are critical for safety. its structure, handle it carefully like for the MOS IC. Replace only with part number specified. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4-3 Yellow Cyan Green White Magenta Red Blue, 12345678910 11 12 13

A CD-604 FLEXIBLE BOARD CCD IMAGER XX MARK:NO MOUNT B

CL006 12 11 1098765

C Note: CD-604 flexible complete board and IC002 are not

supplied, but they are included in CCD block assy.

Note: Voltages of IC001 and IC002 can not be measured, 13 N.C. N.C. 4

because they are mounted by the side of the lens. 14 V8 V2CL001 3 15 V9 VST 2 16 V10 IC002 V1 1 17 CCD-OUT CCD IMAGER CL005

D IC002 H2A 32R001

4.7 18 VH ICX629EQP-13 H1A 31 LND039 VSUB 39 19 RG VL 30 LND038 VSUB_CONT 38 20 N.C. N.C. 29 LND037 GND 37321LND036 CAM_-7.5V 36 IC001 LND035 V1 35 BUFFER LND034 VST 34 IC001CXA3691EN-T9 LND033 V2 33 21 22 23 24 25 26 27 28

E LND032456R008V3A 32 0.01u

LND031 16VVHLD 31 LND030 V3B 30 C008 R009 LND029 V10 29 0.01u 100k16V C004 LND028 V4 28 0.1u LND027 C001 16VV9 27 R002 R004150k 0.01u LND026 0 16VV5A 26

F LND025 V8 25

LND024 V5B 24 LND023 V7 23 LND022 V6 22 R007 C005 C007 C006 XX XX 0.1u 0.1u

SY-156 LND021 GND 21

(1/7) LND020 C002 C003GND 20 XX 0.1u CN301 LND019 16V Page 4-6 GND 19 of Level 3 LND018 CCD_GND 18 LND017

G GND(NC) 17LND016 CCD_OUT 16

LND015 GND 15 LND014 GND 14 LND013 GND 13 LND012 CAM_12V 12 LND011 GND 11 LND010 GND 10 LND009

H GND 9LND008 RG 8

LND007 GND 7 LND006 H1B 6 LND005 NC 5 LND004 H1A 4 LND003 H2B 3 LND002 H2A 2

I LND001 GND 1

4-5 CD-604 IDRV OUT VCC GND ISF IN H1B V7 H2B V6 CL002 RSS3 V5B GND V5A CL003 WGND V4 SUB V3B CSUB V3A CL004 N.C. VHLD, Schematic diagrams of the SY-156 board are not shown. Pages from 4-6 to 4-12 are not shown., • Refer to page 4-3 for mark 0. 12345678910 11 12 13

A ST-133 BOARD FLASH DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE ST-134

T001

FLEXIBLE BOARD L001 D002MA2YF8000LS0 LND003B 2.2uH45XE_H

C901 R004Note: MIC901 is not supplied, 97u 1M but this is included in C002 C00323LND0014.7u 4.7u 315VCHARGING

ST-134 flexible complete board. CAPACITOR TRIGGER

LND006 LND002 LND048 DISCHARGE FLASH TRIGGER_GND UNIT SP+ SP901 DISCHARGE SPEAKER D003 SP- DOR5352 LND005

C LND047 SELF-TIMER/ 4.2AF ILLUMINATOR

17 16 15 14 13 LND046 250 LND004 LND023 SP+ 23 MIC_SIG 3 XE_L MIC901 5 LND022 SP- 22 REG_GND 2 LND021 MIC_SIG 21 LND045 1 C0070.047u4321250V LND020 REG_GND 20 CN001 14P 4.2 SW PGND Q001 LND019 XAF_LED 19 14 XAF_LED LND044 XAF_LED 14 TIG022TS-S-TL-E

IC001 FLASH DRIVED LND018 D_3.2V 18 13 D_3.2V LND043 D_3.2V 13 SW PGND8765

LND017 XSTRB_FULL 17 12 XSTRB_FULL LND042 XSTRB_FULL 12 5 FLASH CONTROL, 0.1 0 VCC CHARGE CONTROL CHG LND016 I_PEAK 16 11 I_PEAK LND041 I_PEAK 11 IC001 R003 TPS65552RGTR 33 R005 LND015 STRB_ON 15 10 STRB_ON LND040 STRB_ON 10 F_ON XFULL 1M 0 3.2 LND014 STRB_CHARGE 14 9 STRB_CHARGE LND039 STRB_CHARGE 9

SY-156 LND013 ST_5V 13 8 ST_5V LND038 ST_5V 8

(2/7) CN704 LND012 REG_GND 12 7 REG_GND LND037 REG_GND 7 Page 4-7 LND011 REG_GND 11 6 REG_GND LND036 REG_GND 6 of Level 3 LND010 REG_GND 10 5 REG_GND LND035 REG_GND55678

E LND009 REG_GND94REG_GND LND034 REG_GND 4 0.1 0

LND008 REG_GND83ST_UNREG LND033 ST_UNREG 3 LND007 REG_GND72ST_UNREG LND032 ST_UNREG 2 LND006 REG_GND61ST_UNREG LND031 ST_UNREG 1 LND005 ST_UNREG 5 LND004 ST_UNREG 4 C001 C004 C0051u 0.001u 0.1uLND003 ST_UNREG 3

F LND002 ST_UNREG 2

LND001 ST_UNREG 1 4-13 ST-133, ST-1344321N.C HGND I_PEAK N.C G_IGBT VBATT N.C N.C N.C 9 10 11 12, 12345678910 11 12 13 14 15 16

A RL-065 FLEXIBLE BOARD CONTROL SWITCH XX MARK:NO MOUNT Note: RL-065 flexible complete board and S003 (shutter) are not supplied, B but they are included in SW-464 BOARD cabinet (upper) block assy. CONTROL SWITCH

D002 LND001 XPWR_LED 1 CL-196SYG-CD-T(POWER) XX MARK:NO MOUNT LND002 D_3.2V 2 CN002 12P LND003 XPOWER_ON31D_3.2V LND021 D_3.2V 1 R001 R002 R003 R0062200 2200 2200 3300 LND004 KEY_AD042KEY_AD0 LND022 KEY_AD0 2 LND005 KEY_AD153KEY_AD1 LND023 KEY_AD1 3 D001 LND006 PLAY_SW64PLAY_SW LND024 PLAY_SW 4 SML-510MWT86S

C (AE/AF LOCK/SELF-TIMER)LND007 REG_GND75REG_GND LND025 REG_GND 5 SY-156 LND008 XAE_LOCK_LED86XAE_LOCK_LED LND026 XAE_LOCK_LED62121212121

(2/7) LND009 XSTRB_LED97XSTRB_LED LND027 XSTRB_LED 7 CN705 LND010 REG_GND 10 8 N.C LND028 N.C 8 D0024343434343Page 4-7 SML-310YTT86 of Level 3 LND011 N.C 11 9 N.C LND029 N.C 9 (FLASH CHARGING/RECORD) S001 S004 S006 S008 S009 LND012 N.C 12 10 N.C LND030 N.C 10 LND013 N.C 13 11 MODE_DIAL0 LND031 MODE_DIAL0 11 (SELF TIMER) (MACRO) (FLASH) IMAGE (SET) BRIGHTNESS(EV)

D LND014 MODE_DIAL0 14 12 MODE_DIAL1 LND032 MODE_DIAL1 121 2

LND015 MODE_DIAL1 15 LND016 KEY_AD2 16 R004 R0052200 LND017 3 4XAE_LOCK_SW 17 2200 S002 LND018 XSHUTTER_SW 18 POWER LND019 REG_GND 1923D0033232MAZW068H0LS021212121R002 1

XX

LND001 D0051 1 XX43434343

E STATIC_GND S003 S002 S005 S007

D003 D004 C001 LND020 STATIC_GND R0012200 XX XX XX SCREEN IMAGE SIZE MENU

DISPLAY

(PLAYBACK) /DELETE S005 S006 W (ZOOM) T

F (INDEX)

S003 (SHUTTER) 4 3

CONTROL SW BLOCK (SW110T/SW120TB)

2 3 D00112CONTROL SW BLOCK (SW110T/SW120TB) is replaced as block, SW110T: SILVER modelMAZW068H0LS0 so that PRINTED WIRING BOARD is omitted. SW120TB: BLACK model

G R112 R111 R110

2200 3600 8200 10987R109 Twilight 22000 Landscape Beach Snow portrait CN001 6P

H 1 MODE_DIAL0 LND101 MODE_DIAL0 1 Twilight

2 NC LND102 NC23REG_GND LND103 REG_GND354NC LND104 NC 4 ISO 5 MODE_DIAL1 LND105 MODE_DIAL1512346NC LND106 NC 6 Soft snap MOVIE AUTO P_AUTO R116

I

R113 R114 R115 2200 3600 8200 4-14 SW-464, RL-065, SW110T/SW120TB, • Refer to page 4-3 for mark 0. 123456789123456

A JK-303 FLEXIBLE BOARD A DC-104 FLEXIBLE BOARD MULTI/LCD CONNECTOR Note: CN001 (multi connector) is not supplied, BATTERY IN, DC IN XX MARK:NO MOUNT but this is included in JK-303 flexible complete board. XX MARK:NO MOUNT

BT001 CN001 28P CHARGE_V LITHIUM (MULTI CONNECTOR) To AV/USB Multi Cable or Cradle LND001 CHARGE_V 14BATTERY LND002 CHARGE_V 13 2 LND001 VL_3V 1 27 S BH001B B LND003 CHARGE_V 12 BATTERYLND002 N.C 2 XSTATION_IN(N.C.) ACV_GND 3 TERMINAL CAHRGE_V 11 LND003 N.C 3 SET_ID_IN(N.C.) ACV_GND LND004 LND005 BATT_SIG 10LND004 USB_VBUS 4 USB_VBUS ACV_GND SY-156 ACV_GND 9 LND005 LND006USB_GND 5 USB_GND XPOWER_ON(N.C.) (7/7) LND006 3 LND007 ACV_GND85USB_DP 6 USB_DP KEY_A/DB(N.C.) CN701224Page 4-12 LND008 ACV_GND 7 LND007 N.C 7 USB_DM N.C. of Level 3 ACV_GND 6 LF001 3 J001 LND008 LF001 LND009USB_DM 8 USB_GND N.C. 341DC IN LND010 ACV_UNREG 5 LND009 USB_GND 9 A_OUT_L KEY_A/DA(N.C.) 1 2 LND011 ACV_UNREG 4C 4LND010 A_GND 10 A_GND CHARGE_V(N.C.)FB001 C LND012 ACV_UNREG 3 LND011 AU_LINE_OUT 11 V_OUT BATT_XEXT LND013 ACV_UNREG 2 LND012 V_GND 12 V_GND CHARGE_V(N.C.) FB002 LND014 BATT/XEXT 1 LND013 V_LINE_OUT 13 XCHG_ON(N.C.) ACV_UNREG LND014 XAV_JACK_IN 14 XAV_JACK_IN ACV_UNREG LND018 STATIC_GND LND015 N.C 15 28 LND040 LND016 ACV_GND 16 STATIC_GND

D SY-156

LND017 ACV_GND 17 (6/7) LND018 ACV_GND 18 D CN702 LND019 ACV_GND 19 Page 4-11 of Level 3 LND020 ACV_GND 20 LND021 ACV_GND 21 05 LND022 ACV_GND 22 LND023 N.C 23 LND024 N.C 24 LND025 N.C 25

E LND026 N.C 26

LND027 N.C 27 LND028 N.C 28 LND029 N.C 29 LND030 N.C 30 LND031 BATT/XEXT 31 LND032 ACV_UNREG 32 LND033 ACV_UNREG 33

F LND034 ACV_UNREG 34

LND035 ACV_UNREG 35 LND036 ACV_UNREG 36 LND037 ACV_UNREG 37 LND038 ACV_UNREG 38 LND039 ACV_UNREG 39 LND129 N.C. 29 CN102 24P

G LND128 COM 28 1 COM

LND127 CS 27 2 CS LND126 VST 26 3 VST LND125 VCK 25 4 VCK LND124 EN 24 5 EN LND123 DWN 23 6 DWN LND122 VDD 22 7 VDD LND121 VSS 21 8 VSS

H LND120 N.C. 20 9 N.C.

LND119 VSSG 19 10 VSSG LCD901 LND118 XSTBY 18 11 XSTBY 2.5INCHCOLOR

LCD SY-156 LND117 PCG 17 12 PCG MONITOR

(5/7) LND116 HST 16 13 HST CN901 LND115 REF 15 14 REF Page 4-10 of Level 3 LND114 TEST1(N.C.) 14 15 TEST1(N.C.) LND113 VSS 13 16 N.C.

I LND112 HCK2 12 17 HCK2

LND111 HCK1 11 18 HCK1 LND110 PSIG 10 19 PSIG LND109G920 G LND108R821 R LND107B722 B LND106 RGT 6 23 RGT LND105 TEST2(N.C.) 5 24 TEST2(N.C.)

J LND104 N.C. 4

LND103 BL_L 3 LND102 N.C. 2 CN101 6P LND101 BL_H16BL_H D901BACKLIGHT 5 NC 4 NC 3 NC 2 NC

K 1 BL_L

4-15 JK-303, DC-104 26 24 22 20 18 16 14 12 10864225 23 21 19 17 15 13 1197531, 4-3. PRINTED WIRING BOARDS Link CD-604 FLEXIBLE BOARD RL-065 FLEXIBLE BOARD ST-133 BOARD JK-303 FLEXIBLE BOARD ST-134 FLEXIBLE BOARD DC-104 FLEXIBLE BOARD SW-464 BOARD COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION, 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 1221324334654456• There are a few cases that the part printed on diagram isn’t mounted in this model. 543345411221123321• C: panel designation32414-17,

CD-604 (2 layers)

: Uses unleaded solder.

CD-604 FLEXIBLE BOARD

39 LND039LND038 LND037 LND036 LND035 LND034 LND033 A LND032 LND031 CD-604 LND030 LND029 LND028 >PI< LND027 LND026 LND025 LND024 1-867-705- LND023 LND022 LND021 LND020 CL002 CL001 LND019 LND018 LND017 LND016 C001 R001 CL006 CL003 CL004 LND015 LND014 LND013 LND012 CL005 LND011 LND010 LND009 LND008 LND007 LND006 C008 LND005 LND004 LND003 R009 LND002 1 LND001 R008 C002 12 5 13 4

IC002 32

20 29 1-867-705- 12 21 28

Note: CD-604 flexible complete board and IC002 are not supplied,

but they are included in CCD block assy. 4-19 CD-604 R002 R00464R007 C00413C003 IC001 C005 C006 C007, Printed wiring boards of the SY-156 board are not shown. Page 4-20 is not shown.,

ST-133 (4 layers), ST-134 (2 layers)

: Uses unleaded solder.

ST-133 BOARD (SIDE B) FLASH UNIT

XE_L XE_H TRIGGER_GND

ST-133 BOARD (SIDE A) TRIGGER ST-133

LND004 >EP GW< LND003B IC00141516 14 8 13 C007 001 9 12 C001 CN 1 1-867-701- 11 LND002 LND001

D003 D003 SELF-TIMER/ AF ILLUMINATOR

LND005 LND006 1-867-701- 11 05 05 +

C901 CHARGING ST-134 FLEXIBLE BOARD CAPACITOR

SP- SP+

SP901 SPEAKER

MIC901

ST-134

>PI<

Note: MIC901 is not supplied, but this is included in ST-134 flexible complete board.

1 23 1-867-792- 11 4-21 ST-133, ST-13445T001321LND047 LND048 LND046 LND045 C002 LND044 C003 LND043 LND042 LND041 LND040 L001 LND039 LND038 LND037 LND036 LND03531LND034 LND033 LND032 LND031

ST-133

4641

Q001

5 8 R005 R003 R004 C005 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023 C004

D002

, SW-464 (2 layers) : Uses unleaded solder.

SW-464 BOARD (SIDE A)

D001 SW-464 BOARD (SIDE B) AE/AF LOCK/ 2 4 SELF-TIMER S003 S003 LND001 (PLAYBACK) D00213

A C001FLASH CHARGING32A

/RECORD D003 1 D004 1 CN0022 3 12 1 S002

SCREEN DISPLAY B R00431B

S00242CN001 S00761

MENU

2 4 S007 S00613(FLASH)

C R006 R00224C

S00613S009 S008 3 1S009 S004

IMAGE

BRIGHTNESS (SET) (MACRO)4 2 (EV) R00131S001

D S001

(SELF TIMER) D R00542S00524IMAGE SIZE /DELETE S005 1-867-709- 11131-867-709- 11 051233214-22 SW-464 D001AKKAD002 D005 R00324S0081331S004 4 2,

RL-065 (2 layers), JK-303 (2 layers), DC-104 (2 layers)

: Uses unleaded solder.

RL-065 FLEXIBLE BOARD DC-104 FLEXIBLE BOARD

1 19 + S - BH001

Note: RL-065 flexible complete board and S003 (shutter) are not supplied, 1 3

but they are included in cabinet (upper) block assy. LND018

S005 S006 W T J001 DC IN D002

LND020 (POWER) RL-065 S>0P0I3< (SHUTTER) A211-867-704- 11 S003 S0034R00223R001

D003 S002 1-868-392- 11 05

14 1

POWER JK-303 FLEXIBLE BOARD

1 LND101 LND102 BT001 LND103 LND104 LND105 303-KJ 1 12 LND106LND107 LND108 BATTERY, LND109 -707-768-1 LND110 LND111 LND112 LITHIUM SECONDARY LND113 LND114 LND115 LND116 LND117 LND118 LND119 LND120 LND121 LND122 LND123 LND124 LND125 LND126 LND127 29 LND128LND129 1 LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 BT001 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND020 LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032 LND033 LND034 LND035 LND036 FB001 LND037 LF001 39 LND038LND0392143BCN101 262124 28 27 CN102 25 1 LND040 CN001 1-867-707- 11 (MULTI CONNECTOR)

CAUTION Note: CN001 (multi connector) is not supplied, Danger of explosion if battery is incorrectly replaced.

but this is included in JK-303 flexible complete board. Replace only with the same or equivalent type. 4-23 RL-065, JK-303, DC-10442S00231

D002

LND001 LND002 LND003 LND004 LND005 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND014 LND015 LND016 LND017 LND018 LND019 LND021 LND022 LND023 LND024 LND025 LND026 LND027 LND028 LND029 LND030 LND031 LND032

D001

3 2 S006 -392- LND001 LND002 LND003 LND004 LND005 FB002 LND006 LND007 LND008 LND009 LND010 LND011 LND012 LND013 LND01431LF0014213J0011645

DC-104

>PI<, Mounted parts location of the SY-156 board are not shown. Page 4-25 is not shown., 4-3. PRINTED WIRING BOARDS 4-4. MOUNTED PARTS LOCATION no mark : side A * mark : side B SW-464 BOARD CN001 B-3 * CN002 A-2 D001 A-1 D002 A-1 R001 D-3 R002 C-3 R003 C-2 R004 B-2 R005 D-2 R006 C-2 S001 D-3 S002 B-2 S003 A-1 S004 D-3 S005 D-2 S006 C-3 S007 C-2 S008 D-2 S009 D-3 4-26E SW-464,

NOTE

5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCCABINET BLOCK LCD BLOCK LENS BLOCK

D

BT HOLDER BLOCK

Link ELECTRICAL PARTS LIST ACCESSORIES

CD-604 FLEXIBLE BOARD C RL-065 FLEXIBLE BOARD B ST-134 FLEXIBLE BOARD C DC-104 FLEXIBLE BOARD D ST-133 BOARD C SW-464 BOARD B JK-303 FLEXIBLE BOARD D, 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant le numéro spécifié. uF: µF • COILS • Color Indication of Appearance Parts uH: µH Example: • RESISTORS (SILVER): Cabinet’s Color All resistors are in ohms. (Silver): Parts Color METAL: metal-film resistor METAL OXIDE: Metal Oxide-film resistor F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model • Language that can be selected about SY-156 board GP1Jz

US CND

GP2zzzzzz

AUS

Vietnam

AEP

GP3zzzzzzzzzzzzzzz

UK E AR BR TW

GP4zzzzzzzzz

JE HK CH KR

5-1 Area Japanese English French German Spanish Italian Portugal Simplified Chinese Traditional Chinese Arabic Dutch Russian Swedish Korean Norwegian Danish Finnish Polish Hungarian Czech Persian Thai, 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS DISASSEMBLY HARDWARE LIST 5-1-1. CABINET BLOCK #18 #18 #18 #18 LCD Block (See page 5-3.) #18 Ref. No. Part No. Description Ref. No. Part No. Description 1 A-1166-430-A CABINET (FRONT) BLOCK ASSY (SILVER) 5 A-1166-458-A CABINET (REAR) BLOCK ASSY (SILVER) 1 A-1166-433-A CABINET (FRONT) BLOCK ASSY (BLACK) 5 A-1166-461-A CABINET (REAR) BLOCK ASSY (BLACK) 2 2-666-506-01 CABINET, BT SIDE 6 2-666-491-01 SHEET (130), WINDOW ADHESIVE 3 2-666-418-01 BRACKET, STRAP 7 2-666-505-01 WINDOW (130), LCD 4 2-666-507-01 CABINET, LE SIDE #18 2-635-591-21 SCREW (M1.4), NEW TRUSTAR P2 (Silver) 5-2, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

5-1-2. LCD BLOCK #5 (including RL-065 flexible board) LCD901 D901 #5 SW-46 544 Lens Block (See page 5-4.) Ref. No. Part No. Description Ref. No. Part No. Description 51 A-1167-019-A SW-464 BOARD, COMPLETE 55 3-072-500-01 TAPE (N) 52 1-479-584-11 CONTROL SW BLOCK (SW110T) (SILVER) D901 1-479-554-21 BLOCK, LIGHT GUIDE PLATE (2.5) 52 1-479-584-21 CONTROL SW BLOCK (SW120TB) (BLACK) LCD901 8-753-257-48 ACX336AKA-3 53 A-1166-159-A CABINET (UPPER) BLOCK ASSY (including RL-065 flexible board) #5 3-080-204-01 SCREW, TAPPING, P2 (Black) * 54 2-666-428-01 SHEET (130), LCD REINFORCEMENT 5-3, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

BT holder Block 5-1-3. LENS BLOCK (See page 5-5.) ns: not supplied (including MIC901) 112 111 ST-13 SP9014 ns (including IC002 (CCD imager) and CD-604 flexible board) (Note 1, 2) ST-133 #19 CD-604 ns (Note 4) C901 108 (Note 3) (Note 3) ns (Note 3) 106 ns (Note 3, 4) M901 (Note 4) ns ns Note 1: CCD block assembly is including CD-604 flex- Note 3: Be sure to read “Exchange method of barrier as- ible completed board. sembly” on page 2-6. Note 2: Be sure to read “Precuations for Replacement of Note 4: Be sure to read “Exchange method of zoom mo- Imager” on page 4-3. tor unit” on page 2-9. • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description 0101 A-1182-558-A ST-133 BOARD, COMPLETE 108 2-673-652-01 BARRIER ASSY (Note 3) 0102 1-479-601-11 FLASH UNIT 109 2-673-651-01 TAPPING SCREW (B1.2X4) (Note 3) * 103 2-666-420-01 HOLDER, STROBOSCOPE 110 2-673-649-01 BT2 P1.4X3 B3C (Note 4) 104 A-1183-052-A ST-134 FLEXIBLE BOARD, COMPLETE (including MIC901) 111 3-941-343-01 TAPE (A) 105 A-1166-148-A CCD BLOCK ASSY (including IC002 * 112 2-678-568-01 SHEET, ST PROTECTION (CCD IMAGER) and CD-604 flexible board) 0* C901 1-112-819-11 ELECT 97uF 315V (Note 1, 2) M901 2-673-648-01 ZOOM MOTOR UNIT (Note 4) SP901 1-826-281-11 LOUDSPEAKER (1.0CM) 106 1-788-363-11 OPTICAL UNIT (ED13A) (Note 3, 4) 107 2-673-650-01 RING (A), ORNAMENTAL (Note 3) #19 3-086-156-21 SCREW B1.2 (Red) 5-4, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

5-1-4. BT HOLDER BLOCK DC-104 SY-156 153 JK-303 #5 BT001 151 154 #18 152 ! : BT001 (BATTERY, LITHIUM SECONDARY) Board on the mount position. (See page 4-23.) #18

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. * Refer to the table of page 5-1 about language of SY-156 board. • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description 151 A-1191-615-A SY-156 BOARD, COMPLETE (SERVICE) (GP4) 157 2-666-426-01 LID (130), DC 151 A-1191-616-A SY-156 BOARD, COMPLETE (SERVICE) (GP2) 151 A-1191-617-A SY-156 BOARD, COMPLETE (SERVICE) (GP3) 158 A-1166-045-A DC-104 FLEXIBLE BOARD, COMPLETE * 152 2-666-424-01 PLATE, MULTI FIXED * 159 2-666-427-01 CUSHION (130), LENS 153 2-666-423-01 SCREW (130), TRIPOD * 160 2-666-429-01 CUSHION, CD RADIATION * 161 2-666-422-01 FRAME (130), LCD 154 A-1166-050-A JK-303 FLEXIBLE BOARD, COMPLETE 0BT001 1-528-999-61 BATTERY, LITHIUM SECONDARY * 155 2-666-425-01 PLATE (130), BT GROUND 156 X-2108-259-1 HOLDER ASSY (130) (J), BT (SILVER) #5 3-080-204-01 SCREW, TAPPING, P2 (Black) 156 X-2108-260-1 HOLDER ASSY (130) (J), BT (BLACK) #18 2-635-591-21 SCREW (M1.4), NEW TRUSTAR P2 (Silver) 5-5,

CD-604 DC-104 JK-303 RL-065 ST-133

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1166-148-A CCD BLOCK ASSY (Note 1) < FERRITE BEAD > (Not supplied) CD-604 FLEXIBLE BOARD, COMPLETE ******************************* FB001 1-469-580-11 INDUCTOR, FERRITE BEAD (1005) (CD-604 flexible complete board and IC002 are not supplied, FB002 1-469-580-11 INDUCTOR, FERRITE BEAD (1005) but they are included in CCD block assy.) < LINE FILTER > < CAPACITOR > LF001 1-456-583-11 COMMON MODE CHOKE COIL C001 1-164-943-81 CERAMIC CHIP 0.01uF 10% 16V C003 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C004 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V A-1166-159-A CABINET (UPPER) BLOCK ASSY C006 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (Not supplied) RL-065 FLEXIBLE BOARD, COMPLETE C007 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V ******************************* (RL-065 flexible complete board and S003 (shutter) are not supplied, C008 1-164-943-81 CERAMIC CHIP 0.01uF 10% 16V but they are included in cabinet (upper) block assy.) < IC > < DIODE > IC001 8-753-230-85 IC CXA3691EN-T9 D001 6-500-776-01 DIODE MAZW068H0LS0 IC002 (Not supplied) ICX629EQP-13 (Note 1) D002 6-500-594-01 DIODE CL-196SYG-CD-T (POWER) D003 6-500-776-01 DIODE MAZW068H0LS0 < RESISTOR > < RESISTOR > R001 1-220-803-81 RES-CHIP 4.7 5% 1/16W R002 1-218-990-81 SHORT CHIP 0 R001 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R004 1-218-979-11 RES-CHIP 150K 5% 1/16W R008 1-164-943-81 CERAMIC CHIP 0.01uF 10% 16V < SWITCH > (Note 2) R009 1-218-977-11 RES-CHIP 100K 5% 1/16W S002 1-786-157-11 SWITCH, TACTILE (POWER) S003 (Not supplied) TACTILE SWITCH (SHUTTER) S005 1-786-180-31 SWITCH, PUSH (1KEY) (W (ZOOM)/INDEX) A-1166-045-A DC-104 FLEXIBLE BOARD, COMPLETE S006 1-786-179-31 SWITCH, PUSH (1KEY) (T (ZOOM)) ******************************* < BATTERY TERMINAL > 0 A-1182-558-A ST-133 BOARD, COMPLETE ********************** 0BH001 1-780-061-21 BATTERY TERMINAL BOARD 0 1-479-601-11 FLASH UNIT < JACK > < CAPACITOR > J001 1-817-331-11 DC JACK 5P C001 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < LINE FILTER > C002 1-131-860-11 TANTAL. CHIP 4.7uF 20% 10V C003 1-131-860-11 TANTAL. CHIP 4.7uF 20% 10V * LF001 1-457-217-21 COMMON MODE CHOKE COIL C004 1-165-908-11 CERAMIC CHIP 1uF 10% 10V C005 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V A-1166-050-A JK-303 FLEXIBLE BOARD, COMPLETE 0C007 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V ****************************** 0* C901 1-112-819-11 ELECT 97uF 315V (CN001 (multi connector) is not supplied, but this is included in JK-303 flexible complete board.) < CONNECTOR > < BATTERY > CN001 1-815-762-51 CONNECTOR, FFC/FPC 14P 0BT001 1-528-999-61 BATTERY, LITHIUM SECONDARY < DIODE > < CONNECTOR > 0* D002 6-501-433-01 DIODE MA2YF8000LS0 CN001 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) * D003 6-501-364-01 DIODE DOR5352 * CN101 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P (SELF-TIMER/AF ILLUMINATOR) * CN102 1-816-650-51 FFC/FPC CONNECTOR (LIF) 24P < IC > Note 1: Be sure to read “Precautions for Replacement of Imager” on page 4-3 when changing the imager. IC001 6-707-555-01 IC TPS65552RGTR Note 2: Capacitor is mounted to the location where R008 is printed. < COIL > CAUTION * L001 1-400-820-11 INDUCTOR 2.2uH Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. 5-6,

ST-133 ST-134 SW-464

Ref. No. Part No. Description Ref. No. Part No. Description < TRANSISTOR >

Electrical parts list of the SY-156 board is

0* Q001 6-551-447-01 TRANSISTOR TIG022TS-S-TL-E not shown.

Pages 5-8 to 5-11 are not shown.

< RESISTOR > R003 1-216-803-11 METAL CHIP 33 5% 1/10W 0R004 1-216-121-11 RES-CHIP 1M 5% 1/10W R005 1-216-857-11 METAL CHIP 1M 5% 1/10W < TRANSFORMER > 0T001 1-443-648-21 DC-DC CONVERTER TRANSFORMER A-1183-052-A ST-134 FLEXIBLE BOARD, COMPLETE ****************************** (MIC901 is not supplied, but this is included in ST-134 flexible complete board.) < MICROPHONE > MIC901 (Not supplied) MICROPHONE BLOCK < SPEAKER > SP901 1-826-281-11 LOUDSPEAKER (1.0CM) A-1167-019-A SW-464 BOARD, COMPLETE *********************** < CONNECTOR > * CN001 1-816-654-51 FFC/FPC CONNECTOR (LIF) 6P * CN002 1-816-644-51 FFC/FPC CONNECTOR (LIF) 12P < DIODE > D001 8-719-075-29 DIODE SML-510MWT86S (AE/AF LOCK/SELF-TIMER) D002 8-719-077-34 DIODE SML-310YTT86 (FLASH CHARGING/RECORD) < RESISTOR > R001 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R002 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R003 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R004 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R005 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R006 1-218-959-11 RES-CHIP 3.3K 5% 1/16W < SWITCH > S001 1-786-885-41 SWITCH, TACTILE (V (SELF TIMER)) S002 1-786-885-41 SWITCH, TACTILE (SCREEN DISPLAY) S003 1-786-885-41 SWITCH, TACTILE (N (PLAYBACK)) S004 1-786-885-41 SWITCH, TACTILE (B (MACRO)) S005 1-786-885-41 SWITCH, TACTILE (IMAGE SIZE/DELETE) S006 1-786-885-41 SWITCH, TACTILE (v (FLASH)) S007 1-786-885-41 SWITCH, TACTILE (MENU) S008 1-786-885-41 SWITCH, TACTILE (b (IMAGE BRIGHTNESS (EV))) S009 1-786-885-41 SWITCH, TACTILE (z (SET)) • Refer to page 5-1 for mark 0. 5-7,

Checking supplied accessories. Other accessories

2-673-237-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (AEP, UK, E, HK, AUS, JE) 2-673-237-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (AEP) 2-673-237-31 INSTRUCTION (READ THIS FIRST) Battery Charger Battery Charger (SPANISH, PORTUGUESE) (AEP, E, AR, JE) BC-CSG BC-CSG 2-673-237-41 INSTRUCTION (READ THIS FIRST) (GERMAN, DUTCH) 0 1-479-583-21 0 1-479-583-31 (AEP) (US, CND) (EXCEPT US, CND) 2-673-237-51 INSTRUCTION (READ THIS FIRST) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) 2-673-237-61 INSTRUCTION (READ THIS FIRST) (RUSSIAN) (AEP) 2-673-237-71 INSTRUCTION (READ THIS FIRST) (ARABIC, PERSIAN) (E) USB/AV Cable for Power Cord 2-673-237-81 INSTRUCTION (READ THIS FIRST) (KOREAN) (KR, JE) Multi-use Terminal 0 1-555-074-71 (AUS) 2-673-237-91 INSTRUCTION (READ THIS FIRST) (CZECH, POLISH) 1-829-866-31 0 1-782-476-41 (CH) (AEP) 0 1-783-374-22 (HK) 2-673-238-11 INSTRUCTION (READ THIS FIRST) 0 1-783-952-51 (AR) (HUNGARIAN, SLOVAK) (AEP) 0 1-792-549-31 (JE) 0 1-823-947-51 (KR) 2-673-238-21 INSTRUCTION (READ THIS FIRST) 0 1-824-910-31 (AEP, E) (SWEDISH, FINNISH) (AEP) 0 1-827-269-22 (UK) 2-673-238-31 INSTRUCTION (READ THIS FIRST) (NORWEGIAN, DANISH) (AEP) 2-673-368-11 INSTRUCTION (READ THIS FIRST) (ENGLISH) (US, CND) 2-673-368-21 INSTRUCTION (READ THIS FIRST) (FRENCH, ITALIAN) (CND) 2-673-239-11 INSTRUCTION (USER'S GUIDE) (ENGLISH) (EXCEPT KR, AR, CH) Rechargeable Battery Pack Battery Case NP-BG1 (not supplied) 2-673-239-21 INSTRUCTION (USER'S GUIDE) (not supplied) (FRENCH, ITALIAN) (CND, AEP) 2-673-239-31 INSTRUCTION (USER'S GUIDE) (SPANISH, PORTUGUESE) (AEP, E, AR, JE) 2-673-239-41 INSTRUCTION (USER'S GUIDE) (GERMAN, DUTCH) (AEP) 2-673-239-51 INSTRUCTION (USER'S GUIDE) (TRADITIONAL CHINESE, SIMPLIFIED CHINESE) (E, HK, CH, JE) Wrist Strap CD-ROM 2-673-239-61 INSTRUCTION (USER'S GUIDE) (RUSSIAN) (AEP) 2-050-981-01 (Cyber-shot Application Software) 2-666-673-01 2-673-239-71 INSTRUCTION (USER'S GUIDE) (ARABIC, PERSIAN) (E) 2-673-239-81 INSTRUCTION (USER'S GUIDE) (KOREAN) (KR, JE) 2-673-239-91 INSTRUCTION (USER'S GUIDE) (CZECH, POLISH) (AEP) 2-673-259-11 INSTRUCTION (USER'S GUIDE) (HUNGARIAN, SLOVAK) (AEP) 2-673-259-21 INSTRUCTION (USER'S GUIDE) (SWEDISH, FINNISH) (AEP) Conversion (2P) Adaptor Conversion (2P) Adaptor 0 1-569-007-12 (JE) 0 1-569-008-12 (E) 2-673-259-31 INSTRUCTION (USER'S GUIDE) (NORWEGIAN, DANISH) (AEP) • Refer to the page 5-1 for mark 0. 5-12E,

HARDWARE LIST (1/2)

#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 1.7 1.7 1.7 1.4 2.5 4.0 2.5 2.5 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver) (Black) (Silver) 3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01 1.7 1.4 1.7 1.7 3.5 1.7 1.6 3.5 #9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping) (Silver) (Silver) (Silver) (Black) 3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21 1.7 1.7 1.7 1.7 5.0 4.0 4.0 5.0 #13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5 (Silver) (Silver) (Silver) (Silver) 3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01 1.7 1.7 1.4 1.4 2.5 2.5 1.5 2.5 #17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0 (Silver) (Silver) (Red) (Silver) 2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31 1.7 2.2 1.4 1.2 1.4 1.5 2.5 4.0 3.0 3.5,

HARDWARE LIST (2/2)

#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 1.4 1.7 1.7 1.7 3.0 5.0 4.0 5.5 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver) (Black) (Dark Silver) 2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61 1.7 1.4 1.4 1.4 3.0 2.0 2.0 4.0 #29: M1.4 X 2.5 #30: M1.2 X 4.0 (Tapping) (Black) (White) 2-662-396-01 3-086-156-11 1.4 1.2 2.5 3.5, [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once 1. Click the Print button . • To reverse the previous screens (operation) one by one, click 2. Specify a printer, print range, number of copies, and other op- the . tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click the . Application of printing: To set a range to be printed within a page, select the graphic Application to the Service Manual: selection tool and drag on the page to enclose a range to This function allows you to go and back between circuit dia- be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it will be convenient for the voltage check. Finding a text 1. Click the Find button . Moving with link 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool , or graphic selection tool . Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing “Find”. page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.) Moving with bookmark: Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.) Application to the Service Manual: The parts on the drawing pages (block diagrams, circuit dia- grams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display the circuit diagram or printed circuit board diagram succes- “Zoom in/out” sively. • Click the triangle button in the zoom control box to select the Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom- Manual depending on the date of issue. ing in or out. Switching a page • To move to the first page, click the . • To move to the last page, click the . “Rotate” • To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each. • To move to the next page, click the . Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set.,

Reverse 987694631.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2006.03 Official Release — —]
15

Similar documents

DSC-W80HDPR SERVICE MANUAL US Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model
DSC-W80HDPR SERVICE MANUAL US Model Ver. 1.0 2007.03 Canadian Model AEP Model E Model Australian Model Hong Kong Model Chinese Model Korean Model [About the service of this model] DSC-W80HDPR is a commondity that packed the Digital Still Camera and Digital Photo Printer Kit. Refer to each following
CAUTION Danger of explosion if battery is incorrectly replaced.
DSC-W70 SERVICE MANUAL LEVEL 3 US Model Ver 1.0 2006.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Tourist Model Photo: Silver Link SERVICE NOTE PRINTED WIRIN
SPECIFICATIONS Camera [Input and Output connectors] Microphone: Monaural
DSC-W80/W85 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Photo: Silver Tourist M
SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-W90 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Photo: Silver Link SPECIFICATIONS BLOCK DI
CAUTION If you have any questions about this product,
MVC-CD350 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Revision History Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD350 COVER SPECIFICATIONS xCamera xAC-L15A/L15B AC Adaptor [System] [Input and
Storage temperature NP-FM50 battery pack Table for difference of functions
MVC-CD200/CD300 SERVICE MANUAL US ModelCanadian Model Level 2 Ver 1.0 2001. 05 AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Tourist Model Korea Model Photo : MVC-CD300 Japanese Model This service manual contains information for japanese model as well. On the SY-67 board
CAUTION WARNING This symbol is intended to alert You are cautioned that any changes or
MVC-CD500 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD500
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model DIGITAL STILL CAMERA
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model Ver 1.0 1998.09 UK Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM CD-206 BOARD CAMERA REC 1 IC431 1,3 78µsec 9.5Vp-p 2 IC431 2,4 µ 9.5Vp-p78 sec 3 IC431 8 1.8Vp-p 78µse
S® Training Manual Digital Camera Sony Mavica Cameras MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01
S® Training Manual Digital Camera Sony Mavica Cameras Models: MVC-FD85 MVC-FD90 MVC-FD95 MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01 Table of Contents Introduction Floppy Disc Drive 41 Common Failures 1 Checking for Floppy Disc Drive Voltage 41 Purpose of this book 1 Checking the
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • C
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model DIGITAL STILL CAMERA
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model SPECIFICATIONS DIGITAL STILL CAMERA • Floppy disk that can be used by the MVC-FD75 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS forma
LCD screen Mass (Approx.) NP-F330 battery pack
MVC-FD87/FD92 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 06 Hong Kong Model Australian Model Korea Model Japanese Model PHoto: MVC-FD92 This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refe
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC Features • Calibration using a 32 kHz external crystal • Adjustable RC frequency with maximum +/-2% accuracy • Tune RC oscillator at any operating voltage and temperature • Tune RC oscillator to any frequency within specification
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 1981A–AVR–03/05 AVR155: Accessing an I2C LCD Display using the AVR® 2-wire Serial Interface Features • Compatible with Philips' I2C protocol • 2-wire Serial Interface Master Driver for Easy Transmit and Receive Function • Initialization and Use ofa2x1
AVR107: Interfacing AVR serial memories
AVR107: Interfacing AVR serial memories Features • Devices: AT25128A/256A, AT25F1024/2048/4096 • Full Serial Memory Functions Support • Memory Array Burst Read • Page Burst Write • Write Protection Detection • On Going Access Detection • Non-blocking Write Access • Access Status Information 1 Introd
AVR120: Characterization and Calibration of the ADC on an AVR
AVR120: Characterization and Calibration of the ADC on an AVR Features • Understanding Analog to Digital Converter (ADC) characteristics • Measuring parameters describing ADC characteristics • Temperature, frequency and supply voltage dependencies • Compensating for offset and gain error Introductio
AVR001 Conditional Assembly and portability macros
AVR001 Conditional Assembly and portability macros Features • Increased portability • Easier Code Writing • Simplified I/O Register Access • Improved Assembly Status Feedback 1 Introduction This application note describes the Conditional Assembly feature present in the AVR Assembler version 1.74 and
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2527A–AVR–9/02 AVR223: Digital Filters with AVR Features • Implementations of Simple Digital Filters • Coefficient and Data Scaling • Fast Implementation of 2nd Order FIR Filter • Compact Implementation Of 8th Order FIR Filter • Fast Implementation of 2nd
8-bit Microcontroller Application Note AVR040: EMC Design Considerations Scope
8-bit Microcontroller Application Note Rev. 1619C–AVR–01/04 AVR040: EMC Design Considerations Scope This application note covers the most common EMC problems designers encounter when using microcontrollers. It will briefly discuss the various phenomena. The refer- ence literature covers EMC design i
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 2508B–AVR–01/04 AVR182: Zero Cross Detector Features • Interrupt Driven • Modular C Source Code • Size Efficient Code • Accurate and Fast Detection • A Minimum of External Components Introduction One of the many issues with developing modern applicati
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity,
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity, allowing the smaller 20-pin AVR to be LED Drive and a • 16 Key Pushbutton Pad in4x4Matrix • 4 Digit Multiplexed LED Display with used. The circuit diagram is shown in
8-bit Microcontroller Application Note AVR180: External Brown-out Protection
8-bit Microcontroller Application Note Rev. 1051B–AVR–05/02 AVR180: External Brown-out Protection Features • Low-voltage Detector • Prevent Register and EEPROM Corruption • Two Discrete Solutions • Integrated IC Solution • Extreme Low-cost Solution • Extreme Low-power Solution • Formulas for Compone
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 1259D–AVR–04/05 AVR134: Real Time Clock (RTC) using the Asynchronous Timer Features • Real Time Clock with Very Low Power Consumption (4 µA @ 3.3V) • Very Low Cost Solution • Adjustable Prescaler to Adjust Precision • Counts Time, Date, Month, and Year wit
  Wiring Diagram
Wiring Diagram Samsung Electronics 6-1
8-bit Microcntroller Application Note
8-bit Microcntroller Application Note Rev. 2532A–AVR–01/03 AVR243: Matrix Keyboard Decoder Features • 64-key Push-button Keyboard in8x8Matrix • No External Components Required • Wakes Up from Sleep Mode on Keypress • Easily Implemented into Other Applications • Low Power Consumption • Software Conta
  Alignment and Adjustments
Alignment and Adjustments 1. Tuner FM THD Adjustment FMOutput Antenna GND SETSSG FREQ. 98 MHz Terminal Oscilloscope Adjustment FM S.S.G Input point FM DETECTOR COIL Speaker (FM DET) Terminal output Input Output 60 dB Distortion Meter Minumum Distortion (0.4% below) (Figure 1-1) Figure1-1 IF CENTER
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2540A–AVR–07/03 AVR104: Buffered Interrupt Controlled EEPROM Writes Features • Flexible Multi-byte EEPROM Buffer • Power Efficient EEPROM Access • Access Control on Buffers • EEPROM Buffer Rewrite Introduction Many applications use the built-in EEPROM of t
  Schematic Diagram - This Document can not be used without Samsung’s authorization -
Schematic Diagram - This Document can not be used without Samsung’s authorization - 7-1 MAIN 7-1 Samsung Electronics 7-2 FRONT - This Document can not be used without Samsung’s authorization - Samsung Electronics 7-2 7-3 DSP - This Document can not be used without Samsung’s authorization - 7-3 Sam
  TroubleShooting
TroubleShooting 9-1 Main 9-1 Samsung Electronics Samsung Electronics 9-2 9-3 Samsung Electronics Samsung Electronics 9-4 9-2 DVD Servo parts 9-5 Samsung Electronics Samsung Electronics 9-6 9-7 Samsung Electronics Samsung Electronics 9-8 9-9 Samsung Electronics Samsung Electronics 9-10 9-11 Samsung
AVR054: Run-time calibration of the internal RC oscillator
AVR054: Run-time calibration of the internal RC oscillator Features • Calibration of internal RC oscillator via UART • LIN 2.0 compatible synchronization/calibration to within +/-2% of target frequency • Alternate run-time synchronization/calibration to within +/-1% of target frequency • Support for