Download: SPECIFICATIONS Camera [Input and Output connectors] Microphone: Monaural

DSC-W80/W85 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.03 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Japanese Model Photo: Silver Tourist Model Link SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST • Precaution on Replacing the SY-173 Board The components identified by Les composants identifiés par une mark 0 or dotted line ...
Author: Tucker Shared: 8/19/19
Downloads: 902 Views: 3947

Content

DSC-W80/W85 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.03 Canadian Model

Revision History AEP Model

UK Model

How to use E Model Acrobat Reader Australian Model

Hong Kong Model Chinese Model

Internal memory Korea Model ON BOARD Argentine Model

Brazilian Model Japanese Model

Photo: Silver Tourist Model

Link

SPECIFICATIONS DISASSEMBLY SCHEMATIC DIAGRAMS MODEL INFORMATION TABLE BLOCK DIAGRAMS PRINTED WIRING BOARDS SERVICE NOTE FRAME SCHEMATIC DIAGRAM REPAIR PARTS LIST • Precaution on Replacing the SY-173 Board The components identified by Les composants identifiés par une mark 0 or dotted line with marque 0 sont critiques pour la mark 0 are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce ber specified. portant le numéro spécifié.

DIGITAL STILL CAMERA

DSC-W80/W85_L2 2007C0500-1 © 2007.3 9-852-194-31 Sony EMCS Co. Published by Kohda TEC,

SPECIFICATIONS Camera [Input and Output connectors] Microphone: Monaural

Multi connector Video output Speaker: Monaural [System] Audio output (Monaural) Exif Print: Compatible Image device: USB communication PRINT Image Matching III: Compatible 7.20 mm (1/2.5 type) color CCD, USB communication: Hi-Speed USB (USB 2.0 PictBridge: Compatible Primary color filter compliant) Total pixel number of camera: [LCD screen] BC-CSG/BC-CSGB/BC-CSGC Approx. 7 410 000 pixels Effective pixel number of camera: LCD panel: 6.2 cm (2.5 type) TFT drive battery charger Approx. 7 201 000 pixels Total number of dots: 115 200 (480 × 240) dots Power requirements: AC 100 to 240 V, 50/60 Hz, Lens: Carl Zeiss Vario-Tessar 3× zoom lens f = [Power, general] 2 W (BC-CSG/BC-CSGC)/ 2.6 W (BC- 5.8 – 17.4 mm (35 – 105 mm when converted Power: Rechargeable battery pack NP-BG1, 3.6 V CSGB) to a 35 mm still camera) F2.8 – 5.2 AC-LS5K AC Adaptor (not supplied), 4.2 V Output voltage: DC 4.2 V, 0.25 A Exposure control: Automatic exposure, Scene Power consumption (during shooting with the Operating temperature: 0 to 40°C (32 to 104°F) Selection (7 modes) LCD screen on): Storage temperature: – 20 to +60°C (–4 to White balance: Automatic, Daylight, Cloudy, 1.1 W +140°F) Fluorescent 1,2,3, Incandescent, Flash Operating temperature: 0 to 40°C (32 to 104°F) Dimensions: Approx. 62 × 24 × 91 mm (2 1/2 × File format (DCF compliant): Storage temperature: –20 to +60°C (–4 to +140°F) 31/32 × 3 5/8 inches) (W/H/D) Still images: Exif Ver. 2.21 JPEG compliant, Dimensions: 91.0 × 58.0 × 22.9 mm (3 5/8 × Mass: Approx. 75 g (2.7 oz) DPOF compatible 2 3/8 × 29/32 inches) (W/H/D, excluding Movies: MPEG1 compliant (Monaural) protrusions) Rechargeable battery pack NP- Recording media: Internal Memory (approx. Mass: BG1 31 MB), “Memory Stick Duo” DSC-W80: Flash:Flash range (ISO sensitivity Approx. 155 g (5.5 oz) (including NP- Used battery: Lithium-ion battery (Recommended exposure Index) set to Auto): BG1 battery pack and strap, etc.) Maximum voltage: DC 4.2 V approx. 0.2 to 3.3 m (7 7/8 inches to 10 feet DSC-W85: Nominal voltage: DC 3.6 V 10 inches) (W)/approx. 0.4 to 1.8 m (1 feet Approx. 166 g (5.9 oz) (including NP- Capacity: 3.4 Wh (960 mAh) 3 3/4 inches to 5 feet 10 7/8 inches) (T) BG1 battery pack and strap, etc.) Design and specifications are subject to change without notice. — 2 —,

Model information table

Model DSC-W80/Silver DSC-W80/Black DSC-W80/White DSC-W80/Pink DSC-W85/Silver US, CND, AEP, UK, US, CND, AEP, US, CND, AEP, US, CND, AEP, Destination CND, AEP, UK, E,E, AUS, HK, CH, UK, E, AUS, HK, UK, E, AUS, HK, UK, E, AUS, HK, AUS, KR KR, AR, BR, J, JE CH, KR, JE CH, KR, J, JE CH, KR, J, JE • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-soldered Unleaded solder connections. Check the entire board surface for solder splashes Boards requiring use of unleaded solder are printed with the lead- and bridges. free mark (LF) indicating the solder contains no lead. 2. Check the interboard wiring to ensure that no wires are (Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point : LEAD FREE MARK them out to the customer and recommend their replacement. Unleaded solder has the following characteristics. 4. Look for parts which, through functioning, show obvious signs • Unleaded solder melts at a temperature about 40°C higher than of deterioration. Point them out to the customer and ordinary solder. recommend their replacement. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. 5. Check the B+ voltage to see it is at the values specified. Soldering irons using a temperature regulator should be set to 6. FLEXIBLE Circuit Board Repairing about 350°C. • Keep the temperature of the soldering iron around 270°C Caution: The printed pattern (copper foil) may peel away if the during repairing. heated tip is applied for too long, so be careful! • Do not touch the soldering iron on the same conductor of the • Strong viscosity circuit board (within 3 times). Unleaded solder is more viscous (sticky, less prone to flow) than • Be careful not to apply force on the conductor when soldering ordinary solder so use caution not to let solder bridges occur such or unsoldering. as on IC pins, etc. • Usable with ordinary solder It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder. — 3 —, TABLE OF CONTENTS Section Title Page 1. SERVICE NOTE 1-1. Precaution on Replacing the SY-173 Board ···················· 1-1 1-2. Self-diagnosis Function ··················································· 1-1 1-3. Process After Fixing Flash Error ····································· 1-2 1-4. Method for Copying or Erasing the Data in Internal Memory ··········································································· 1-3 1-5. How to Write Data to Internal Memory ·························· 1-4 2. DISASSEMBLY 2-1. Identifying Parts ······························································ 2-2 2-2. Disassembly ····································································· 2-3 2-3. Exchange method of barrier block ·································· 2-6 2-4. Exchange method of zoom gear block ···························· 2-8 3. BLOCK DIAGRAMS 3-1. Overall Block Diagram (1/2) ··········································· 3-1 3-2. Overall Block Diagram (2/2) ··········································· 3-2 3-3. Power Block Diagram (1/2) ············································· 3-3 3-4. Power Block Diagram (2/2) ············································· 3-4 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. Frame Schematic Diagram ·············································· 4-1 4-2. Schematic Diagrams ························································ 4-3 4-3. Printed Wiring Boards ··················································· 4-21 4-4. Mounted Parts Location ················································ 4-31 5. REPAIR PARTS LIST 5-1. Exploded Views ······························································· 5-2 5-2. Electrical Parts List ························································· 5-7 — 4 —, 1. SERVICE NOTE ENGLISH JAPANESE 1-1. PRECAUTION ON REPLACING THE SY-173 BOARD DESTINATION DATA When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting. Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”. USB SERIAL No. The set is shipped with a unique ID (USB Serial No.) written in it. This ID has not been written in a new board for service, and therefore it must be entered after the board replacement. Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”. 1-2. SELF-DIAGNOSIS FUNCTION 1-2-1. Self-diagnosis Function 1-2-2. Self-diagnosis Display When problems occur while the unit is operating, the self-diagnosis When problems occur while the unit is operating, the LCD screen function starts working, and displays on the LCD screen what to shows a 4-digit display consisting of an alphabet and numbers, which do. blinks at 3.2 Hz. This 5-character display indicates the “repaired Details of the self-diagnosis functions are provided in the Instruction by:”, “block” in which the problem occurred, and “detailed code” manual. of the problem. LCD screen Blinks at 3.2 Hz

C3200

Repaired by: Block Detailed Code C : Corrected by customer Indicates the appropriate Refer to “1-2-3. Self-diagnosis Code Table”. E : Corrected by service step to be taken. engineer E.g. 13 ...Format the “Memory Stick Duo”. 32 ...Turn on power again. 1-1,

ENGLISH JAPANESE

1-2-3. Self-diagnosis Code Table Self-diagnosis Code Block Detailed Symptom/State Correction Function Code The internal memory has experienced a Format the internal memory. format error. “Memory Stick Duo” is unformatted. Format the “Memory Stick Duo”. C1301“Memory Stick Duo” is broken. Insert a new “Memory Stick Duo”. “Memory Stick Duo” type error Insert a supported “Memory Stick Duo”. The camera cannot read or write data Turn the power off and on again, or taking out and inserting the on the “Memory Stick Duo”. “Memory Stick Duo” several times. C3201Trouble with hardware Turn the power off and on again. Retry turn the power on by the power switch. If it does not Difficult to adjust focus recover, check the focus reset sensor of lens block (pin ws ofE6100(Cannot initialize focus) CN402 on the SY-173 board). If it is OK, check the focus motor drive IC (IC401 on the SY-173 board). Retry turn the power on by the power switch. Check the zoom reset sensor of lens block (pin ra of CN402 on the SY-173 Zoom operations faultE6110board), if zooming is performed when the zoom button is (Cannot initialize zoom lens.) operated. If it is OK, check the zoom motor drive IC (IC401 on the SY-173 board). Check or replacement of the IC for steadyshot (IC503 on the SY- E6202Abnormality of IC for steadyshot. 173 board). Check or replacement of the IC for steadyshot (IC503 on the SY- E6210Lens initializing failure. 173 board). Check the HALL element (PITCH) of optical image stabilizer (pin 5, 6 of CN402 on the SY-173 board). If it is OK, checkE6211Lens overheating (PITCH). PITCH angular velocity sensor (SE502 on the SY-173 board) peripheral circuits. Check the HALL element (YAW) of optical image stabilizer (pin ql, w; of CN402 on the SY-173 board). If it is OK, check YAWE6212Lens overheating (YAW). angular velocity sensor (SE501 on the SY-173 board) peripheral circuits. Check the OIS temp sensor of optical image stabilizer (pin 4 ofE6220Abnormality of thermistor. CN402 on the SY-173 board). E9101Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note) E9200Non-standard battery is used. Use the compatible battery only. Note: After repair, be sure to perform “1-3. PROCESS AFTER FIXING FLASH ERROR”. 1-3. PROCESS AFTER FIXING FLASH ERROR When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed automatically to disabling charge and flash setting. After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen. Method for Initializing the Flash Error Code Initialize Initializes the setting to the default setting. Even if you execute this function, the images stored in the internal memory are retained. 1 Select [Initialize] with v/V/b/B, then press z. The message “Initialize all settings” appears. 2 Select [OK] with v, then press z. The settings are reset to the default setting. To cancel the resetting Select [Cancel] in step 2, then press z. • Make sure that the power is not disconnected during resetting. 1-2 Repaired by:,

ENGLISH JAPANESE

1-4. METHOD FOR COPYING OR ERASING THE DATA IN INTERNAL MEMORY

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.) Note 1: When replacing the SY-173 board, erase the data in internal memory of the board before replacement. Note 2: When replacing the SY-173 board, execute formatting and initialize the internal memory after replacement. Method for Copying the Data in Internal Memory

Copy Copies all images in the internal memory to a “Memory Stick Duo”. 1 Insert a “Memory Stick Duo” having 32 MB or larger capacity. 2 Select [Copy] with v/V/b/B on the control button, then press z. The message “All data in internal memory will be copied” appears. 3 Select [OK] with v, then press z. Copying starts. To cancel the copying Select [Cancel] in step 3, then press z. • Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data. • You cannot copy individual images. • The original images in the internal memory are retained even after copying. To delete the contents of the internal memory, remove the “Memory Stick Duo” after copying, then execute the [Format] command in [Internal Memory Tool]. • When you copy the data in the internal memory to the “Memory Stick Duo”, all the data will be copied. You cannot choose a specific folder on the “Memory Stick Duo” as the destination for the data to be copied.• Even if you copy data, a (Print order) mark is not copied

Method for Formatting the Internal Memory

This item does not appear when a “Memory Stick Duo” is inserted in the camera. Format Formats the internal memory. • Note that formatting irrevocably erases all data in the internal memory, including even protected images. 1 Select [Format] with v/V/b/B on the control button, then press z. The message “All data in internal memory will be erased” appears. 2 Select [OK] with v, then press z. The format is completed. To cancel the formatting Select [Cancel] in step 2, then press z. 1-3,

ENGLISH JAPANESE

1-5. HOW TO WRITE DATA TO INTERNAL MEMORY Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera. This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement. To change the setting, use the write enable tool “WriteEnableTool.exe”. Data writing method 1) Connect the PC to the camera (USB mode: Mass Storage), and switch the driver to the “Sony Seus USB Driver”. 2) Start the Write Enable Tool and the SeusEX. 3) Click the [Activate Write Enable Mode] button of the Write Enable Tool. 4) Upon completion of the setting change, the following message will be displayed. 5) Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage). 6) Write the data read out into the PC to the internal memory of the camera. 7) Disconnect the PC from the camera, and turn off the camera. Note: By turning off the camera, the write enable setting is reset. 1-4, 1. SERVICE NOTE ENGLISH JAPANESE 1-1. SY-173基板交換時の注意 仕向けデータ 補修用基板と交換する時,補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。 ADJ編を参照して,「DESTINATION DATA WRITE」を行ってください。

USBシリアルNo.

セットは,1台毎に異なる固有のID(USB Serial No.)を書き込んだ後,出荷されています。 新品の補修用基板には,このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。 ADJ編を参照して,「USB SERIAL No. INPUT」を行ってください。 1-2. 自己診断機能 1-2-1. 自己診断機能について 1-2-2. 自己診断表示 本機の動作に不具合が生じたとき,自己診断機能が働き, 本機の動作に不具合が生じたとき,LCD画面にアルファベッLCD画面に,どう処置したらよいか判断できる表示を行い トと4桁の数字が表示され,3.2Hzで点滅します。この5文字 ます。自己診断機能については取扱説明書にも掲載されて の表示によって対応者分類および不具合の生じたブロックの います。 分類,不具合の詳細コードを示します。 LCD画面 C : 3 2 : 00 3.2Hz点滅

C3200

対応者分類 ブロック分類 詳細コード C :お客さま自身で対応 対応方法の違いにより分類 「1-2 -3 . 自己診断コード表」 E :サービスエンジニア 例 13 ・・ ・“ メモリースティック を参照 で対応 デュオ”をフォーマッ トする 32 ・・ ・電 源を入れ直す 1-5,

ENGLISH JAPANESE

1-2-3. 自己診断コード表 自己診断コード対応ブロック 詳細 症状/状態 対応/方法 者 機能 コード 内蔵メモリにフォーマットエラーが 内蔵メモリをフォーマットする。 あった。 フォーマットしていない“メモリー “メモリースティック デュオ”をフォーマットする。 スティック デュオ”を入れた。 C1300“メモリースティック デュオ”が 新しい“メモリースティック デュオ”に交換する。 壊れている。 “メモリースティック デュオ”の 規格内の“メモリースティック デュオ”を挿入する。 タイプエラーを検出した。 “メモリースティック デュオ”が 電源の入れ直し,または“メモリースティック デュオ” 読み/書きできない。 の挿し/外しを数回試す。 C3201ハードウェアトラブルを検出した。 電源を入れ直す。 E6100フォーカスが合いにくい。 操作スイッチの電源を入れ直す。 (フォーカスの初期化ができない) 復帰しない場合はレンズブロックのフォーカスリセットセ ンサ(SY-173基板CN402 wsピン)を点検する。異常なけ ればフォーカスモータ駆動IC(SY-173基板IC401)を点検 する。 E6110ズーム動作の異常。 操作スイッチの電源を入れ直す。 (ズームレンズの初期化ができな ズームボタンを操作したときにズーム動作をすればレンズ い) ブロックのズームリセットセンサ(SY-173基板CN402 ra ピン)を点検する。異常なければズームモータ駆動IC (SY-173基板IC401)を点検する。 E6202手振れ補正用ICの異常。 手振れ補正用IC(SY-173基板IC503)を点検または交換す る。 E6210手振れ補正用ICの異常。 手振れ補正用IC(SY-173基板IC503)を点検または交換す (レンズ初期化異常) る。 E6211レンズオーバーヒート(PITCH) 光学手振れ補正ブロックのホール素子(PITCH)(SY-173 基板CN402 5,6ピン)を点検する。異常なければ PITCH角速度センサ(SY-173基板SE502)周辺の回路を点 検する。 E6212レンズオーバーヒート(YAW) 光学手振れ補正ブロックのホール素子(YAW)(SY-173 基板CN402 ql,w;ピン)を点検する。異常なければYAW 角速度センサ(SY-173基板SE501)周辺の回路を点検す る。 E6220サーミスタの異常。 光学手振れ補正ブロックのサーミスタ(SY-173基板CN402 4ピン)を点検する。 E9101フラッシュの充電異常。 フラッシュユニットを点検または交換する。(Note) E9200規定外の充電池が使用された。 規定の充電池を使用する。 Note:交換後は,必ず「1-3. フラッシュエラー発生時の対処法」を行って下さい。 1-6,

ENGLISH JAPANESE

1-3. フラッシュエラー発生時の対処法 本機はフラッシュエラー(自己診断コードE:91:01)が発生した場合,高電圧による異常を防止するために自動的にフラッシュ 充電および発光禁止の設定になります。 フラッシュエラー発生後はエラーの解除を行う必要があります。エラーの解除はホーム画面から初期化操作を実行することによ り行います。 設定リセットお買 い上げ時の設定に戻します。 [設定リセット]を実行しても、内 蔵 メモリーに記録されてい る画 像は削除されません 。 1コントロールボタンの/ / / で[ 設定リセット ] を選び、 中央のを押 す 。 「全ての設定内容をリセットします」 というメッセージが表示される。 2 で[ 実 行 ] を選び、 中央のを押 す 。 設定リセットが実行される。 設定リセットを中止するには手順 2で 、[ キャンセル]を 選 び、 中 央の を 押す 。 設定リセット中は電源が切れないようにご注意ください 。 1-4. 内蔵メモリのデータコピーおよび消去方法 内蔵メモリのデータコピーまたは消去はホーム画面の操作から実行可能です。(消去する場合は内蔵メモリの初期化を行いま す。)

Note1:SY-173基板交換の際は,基板交換前に内蔵メモリのデータを消去して下さい。 Note2:SY-173基板交換の際は,基板交換後に内蔵メモリのフォーマットおよび初期化を実行して下さい。

内蔵メモリのコピー方法コピー内蔵メモリーに記録した画像を、“ メモ リ ース ティックデュ オ”に一括コピーします。 1 32MB以上の容量のある“メモリースティックデュオ”を本体に入れる。 2コントロールボタンの/ / / で[ コピー]を選び、中央のを押す。 「 内蔵メモリーのデータがすべてコピーされます」というメッセージが表示される。 3 で[ 実 行 ]を選び、中央のを押す。 コピーが実行される。 コピーを中止するには手順3で、 [ キャンセル]を選び、中央のを押す。 充 分 に充 電し た バッ テリーをご使用ください。残量の少ないバッテリーを使用して画像ファイルをコピ ー する と 、 バ ッ テリー切れのためデータを転送できなかったり、 データを破損するおそれがあります 。 画 像 ごと のコ ピ ーはできません 。 デー タを コ ピー して も 、内蔵メモリー内 のデ ー タは削除されません。内蔵メモリーの内容を消 去す るに は 、 コ ピー後に“メモリーステ ィ ック デュ オ ”を本 体 から取りはずし 、 [ 内蔵メモリーツー ル] の [ フ ォ ーマット]を行ってください。 デ ータをコピーする と “メモリースティックデュ オ ”内に 新 しいフォルダが作成されま す 。 コピー先のフォルダを指定することはできません。 デ ー タの コピ ー を行っても、 (プリント予約)マークの設定はコピーされません。 内蔵メモリのフォーマット方法 “メモリースティックデュ オ”が本機に入っている場合は表示されません。 フォーマット内蔵メモリーの管理領域をフォーマット( 初 期化 )し ます 。 フ ォーマットすると、プロテクト してある画像も含めて、 すべてのデータが消去さ れ 、 元 に 戻せ ま せん 。 1コントロールボタンの/ / / で[ フォーマット]を選び、中央のを押す。 「 内蔵メモリーのデータがすべて消去されます」というメッセージが表示される。 2 で[ 実 行 ]を選び、中央のを押す。 フォーマットが実行される。 フ ォーマットを中 止 するには手順2で、 [ キャンセル]を選び、中央のを押 す 。 1-7,

ENGLISH JAPANESE

1-5. 内蔵メモリへデータを書き戻す方法 通常は,PCからカメラの内蔵メモリへデータを書き込むことはできない設定になっています。 基板交換後などに,内蔵メモリへデータを書き戻す場合には,この設定を一時的に変更する必要があります。 設定の変更には,書き込み許可ツール(WriteEnableTool.exe)を使用します。 書き戻し方法 1) カメラとPCをマスストレージ接続し,ドライバを“Sony Seus USB Driver”に切り替える。 2) 書き込み許可ツールとSeusEXを起動する。 3) 書き込み許可ツールの[Activate Write Enable Mode]ボタンをクリックする。 4) 設定の変更が終了すると,次のメッセージが表示されます。 5) ドライバを元に戻して、カメラとPCをマスストレージ接続する。 6) PCに読み出しておいたデータをカメラの内蔵メモリに書き込む。 7) カメラとPCの接続を解除し,カメラの電源をOFFにする。 注意: カメラの電源をOFFにすることにより,書き込み許可の設定が解除されます。 1-8E, 2. DISASSEMBLY

NOTE FOR REPAIR

• Make sure that the flat cable and flexible board are not cracked of bent at the terminal. Cut and remove the part of gilt Do not insert the cable insufficiently nor crookedly. which comes off at the point. (Be careful or some • When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped. pieces of gilt may be left inside) • When installing a connector, don’t press down at wire of connector. It is possible that a wire is snapped. • Do not apply excessive load to the gilded flexible board.

DISCHARGING OF THE ST-160 BOARD’S CHARGING CAPACITOR (C901)

The charging capacitor (C901) of the ST-160 board is charged up to the maximum 300 V potential. Note: High-voltage cautions There is a danger of electric shock by this high voltage when the capacitor is handled by hand. The electric shock is caused by Discharging the Capacitor the charged voltage which is kept without discharging when the Short-circuit between the two points main power of the unit is simply turned off. Therefore, the with the short jig about 10 seconds. remaining voltage must be discharged as described below. R:1 kΩ/1 W

Preparing the Short Jig (Part code: 1-215-869-11)

To preparing the short jig, a small clip is attached to each end of a resistor of 1 kΩ /1 W (1-215-869-11). Wrap insulating tape fully around the leads of the resistor to C901 ST-160 Board prevent electrical shock. 1 kΩ/1 W Flash Unit Wrap insulating tape. 2-1, 2-1. IDENTIFYING PARTS

SW-494 Board Release Block

⋅ Cabinet (Rear)RL-071/078 Board

BT Holder MC-176 Board SY-173 Board LCD Module Main Frame Cabinet (Front) Lens Block Flash Unit ⋅ Barrier Block

⋅ ST-160 Board ⋅ Zoom Gear Block - DISASSEMBLY FLOW - 2-2-1. CABINET SECTION ⋅ Cabinet (Front) ⋅ Cabinet (Rear) 2-2-2. MAIN BOARD SECTION ⋅ Lens Block ⋅ MC-176 Board ⋅ Release Block ⋅ SY-173 Board 2-2-3. LCD/BT HOLDER SECTION 2-3. EXCHANGE METHOD OF 2-4. EXCHANGE METHOD OF ⋅ BT Holder BARRIER BLOCK ZOOM GEAR BLOCK ⋅ Flash Unit ⋅ LCD Module ⋅ Main Frame ⋅ SW-494 Board 2-2,

HELP

2-2. DISASSEMBLY

EXPLODED VIEW HARDWARE LIST

2-2-1. CABINET SECTION Follow the disassembly in the numerical order given. 1Cabinet (Front) (1-1 to 1-8) 2Cabinet (Rear) (2-1 to 2-2) Note:On installation of the cabinet (rear), 2-1 (#65) adjust the position of the mode dial switch and the mode dial. 1-6 (#65) 1-7 (Open) 1-4 (#65)

HELP

2Cabinet (Rear) 2-2 (#65) 1-8 (Claw) 1-1 (#65)

Main Board Section 1-3

(See Page 2-4) 1-5 1-2 (Claw) (#65) 1Cabinet (Front) 2-3, 2-2-2. MAIN BOARD SECTION Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1Release Block (1-1 to 1-3) 2 Lens Block (2-1 to 2-5) 3SY-173 Board (3-1 to 3-11) Note: High-voltage cautions Discharging the Capacitor Short-circuit between the two points with the short jig about 10 seconds. R:1 kΩ/1 W (Part code: 1-215-869-11) C901 ST-160 Board Flash Unit 1-1

LCD/BT Holder

1Release Block Section (See Page 2-5) 2-3 (Release the claw that is the fixation 1-2 of the flash unit (Claw) once) 1-3 3-7 (Claw)

HELP 3-1

3-2 3-11 3-6 2-1 (Claw) 3-3 3-9 2-2 S 3-8 Y-173 (#5) 3-4 (Solder) 3-5 HELP 2-4 (#3) 2-5 3-10 2Lens Block (See Page 2-6, 2-8) 3SY-173 Board 2-4, 2-2-3. LCD/BT HOLDER SECTION Follow the disassembly in the numerical order given. EXPLODED VIEW HARDWARE LIST 1 Flash Unit (1-1) 2 LCD Panel/SW-494 Board (2-1 to 2-4) 3 BT Holder (3-1 to 3-3) 2LCD Panel/ 2-1 SW-494 Board (#5) SW-494

HELP

2-4 (Claw) 2-3 HELP (Claw) 3-2 3-1 (#65) 3-3 2-2 1-1 (Claw) (Claw) HELP 3BT Holder 1Flash Unit 2-5, 2-3. EXCHANGE METHOD OF BARRIER BLOCK Note: Do not hold the part of spring. 2-3-1. HOW TO REMOVE THE ORNAMENTAL RING (A) 1 Turn on the power switch. 2 With the ornamental ring (A) extended, remove the battery forcibly. 3 Apply a solvent to the tweezers or a needle, and dissolve the adhesive on the barrier tapes that secure the ornamental ring (A) to the barrier block. 4 Rotate the ornamental ring (A) clockwise to remove. Tweezers Barrier tape 3 Solvent 4 Ornamental ring (A) Barrier block 2-3-2. HOW TO REMOVE THE BARRIER BLOCK 1 Remove two screws. 2 Remove the barrier block and the inner ring. 2 Barrier block 2 Inner ring 1 Two screws 2-6, 2-3-3. HOW TO INSTALL THE BARRIER BLOCK 1 Install the inner ring and the barrier block. Note: When installing the barrier block, the CAV No. must be located in the lower left position. 2 Secure the barrier block with two screws. *Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm) Note: Check that the barrier feather of the barrier block is not opened slightly or half-closed. Barrier 1 Barrier block feather CAV No. 1 Inner ring 2 Two screws 2-3-4. HOW TO INSTALL THE ORNAMENTAL RING (A) 1 Affix two barrier tapes to the barrier block. Note: The barrier tape must not cover the boss of the barrier block. 2 Install the ornamental ring (A). 1 Barrier tape Boss 1 Barrier tape 2 Ornamental ring (A) Barrier block Note: Turn on and off the power to check the opening and closing of the barrier block with the camera in horizontal, up and down directions respectively. Further, check the zoom motion. Rotate the ornamental ring (A) lightly to check that it is not removed. 2-7, 2-4. EXCHANGE METHOD OF ZOOM GEAR BLOCK Note: Do not hold the part of terminal and the part of spring. 2-4-1. HOW TO REMOVE THE ZOOM GEAR BLOCK • HOW TO REMOVE THE REAR ASSEMBLY 1 Remove the screw, and then the OVF.

OVF

Screw 2 Remove the shutter flexible board from the connector. 3 Remove the vibration-proof flexible board from the connector. 4 Peel the adhesive sheet that secures the vibration-proof flexible board. * When peeling the adhesive sheet, turn it over from the opposite side of the hook. Vibration-proof flexible board 4 Adhesive sheet Connector 2 Shutter flexible board Hook Connector 3 Vibration-proof flexible board 2-8, 5 Peel the adhesive sheet (upper) that secures the main flexible board. 6 Disengage the main flexible board from the hook of the ring assembly, and then slide the main flexible board to remove. 7 Peel the adhesive sheet (lower) that secures the main flexible board. * The FOCUS motor must remain soldered. 6 Main flexible board Hook Ring assembly 5 Adhesive sheet (upper) 7 Adhesive sheet (lower) Solder of FOCUS motor 8 Remove four screws that secure the rear assembly. 9 Remove the rear assembly, disengaging the bosses at four places. * Take care not to get stuck with the vibration-proof flexible board. q; Unhook the Z leaf spring to remove. qa Remove the main flexible board from the ring assembly, and remove the rear assembly and the nuruto gear. qa Nuruto gear 8 Four screws Rear assembly Hook q; Z leaf Boss spring Ring assembly Ring assembly Boss qa Rear assembly qa Main flexible Vibration-proof flexible board board 2-9, • HOW TO REMOVE THE ZOOM GEAR BLOCK 1 Unsolder the zoom motor. 2 Remove the FG leaf spring. 3 Remove the main flexible board from the zoom gear block. 4 Remove the zoom gear block. Rear assembly 3 Main flexible board 4 Zoom gear block 3 Main flexible board 1 Solder Hook 2 FG leaf spring 2-4-2. HOW TO INSTALL THE ZOOM GEAR BLOCK • HOW TO INSTALL THE ZOOM GEAR BLOCK 1 Solder the main flexible board to the zoom gear block. 2 Install the main flexible board to the zoom gear block. 3 Attach the FG leaf spring. Rear assembly 2 Main flexible board Zoom gear block 2 Main flexible board 1 Solder Hook 3 FG leaf spring 2-10, 4 Apply the lubricant (SRX-4339) to the nuruto gear, and insert it into the ring assembly. * Rotate the gear in the ring assembly in the arrow direction until the end of the gear is not engaged with a concave portion of the ring assembly (because a convex portion of the rear assembly enters the convex portion). Ring assembly Gear Convex portion 4 Nuruto gear 5 Install the zoom gear block on the rear assembly. 6 Engaging four bosses, install the rear assembly on the ring assembly. * The vibration-proof flexible board must be engaged with the hook of the rear assembly. 7 Tighten four screws in the order of A to D. *Tightening torque = 0.049 ± 0.01N • m (0.5 ± 0.1kgf • cm) 8 Check that the projection of the nuruto shaft that protrudes from the rear assembly is within the specified value given below. *Specified value: 0.005 – 0.395mm Hook Ring assembly Boss 6 Vibration-proof flexible board Boss 7 Four screws Nuruto shaftB5Zoom gear block 6 Rear assembly

C D A

Nuruto shaft 0.005 – 0.395mm 2-11, 9 Secure and connect the main flexible board. Main flexible board Hook Hook Z leaf spring Ring assembly Main flexible board Hook Adhesive sheet (upper) Adhesive sheet (lower) q; Secure and connect the vibration-proof flexible board and the shutter flexible board respectively. Vibration-proof flexible board Adhesive sheet Connector Shutter flexible board Hook Connector Bousin flexible board 2-12, qa Install the OVF. *When installing the OVF, fit a projection of OVF in the groove of the ring assembly.

OVF

Projection Ring assembly Groove Screw 2-4-3. CHECK THE OPERATION Confirm the operation after installing the lens block in the set. 1 Power ON/OFF 2 Expansion and contraction confirming of lens and opening and shutting confirmation of barrier. Confirm there are neither dirt nor wounds in the surface of the ornamental ring (A) and lens if there is no problem in operation. Wipe off when dirty. 3 Confirm the operation with Wide/Tele. Note: Do not be of caught etc. Do not allophone. 2-13E,

HELP

Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown. Cabinet (front) assy SY electrostatic sheet RL-071/078 Harness (Black) board Harness (Red) Microphone BT holder Main frame Light interception 1mm sheet LC flexible sheet

HELP

,

INSTALLATION METHOD OF BATTERY TERMINAL BOARD

1 Insert the battery terminal board into a slit in the BT holder to install. * The battery terminal board is attached with the notch for installation. BT holder Notch Battery terminal board Battery terminal board 2 Fold the notch 3 or 4 times repeatedly to break. Notch Notch Battery terminal board • HARNESS ARRANGEMENT Harness (Red) SY-173 board Harness (White) Harness (Black)

HELP

, 3. BLOCK DIAGRAMS Link OVERALL BLOCK DIAGRAM (1/2) POWER BLOCK DIAGRAM (1/2) OVERALL BLOCK DIAGRAM (2/2) POWER BLOCK DIAGRAM (2/2), 3. BLOCK DIAGRAMS 3-1. OVERALL BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

LENS BLOCK CD-701 FLEXIBLE BOARD SY-173 BOARD (1/2) LCD901 (1/2)

LCD MODULE LENS IRIS (METER) CN301 CN713 IC004 CCD_OUT 17 10 14 6 H10 CA_AD00 - CA_AD13 LCD_D0 - LCD_D7 D0 - D7

BUFFER

IC003 7M CCD

IMAGER

IC304 H1A,H2A,H1B,H2B CA_HD LCD_CK, LCD_HD, LCD_VD DCLK, HSYNC, VSYNC CCD SIGNAL A2 AE23CA_FD 2.5INCH PROCESS, A3 AF22 COLOR SHUTTER ZOOM FOCUS IRIS TIMING GEN_TG_CLK XCS_ PANEL SPENA LCD MOTOR MOTOR MOTOR MOTOR A4 AF18 U19 36 19 34 RG GENERATOR XDD_SYS_RST K4 IC211 37 RESET Z

MMMM(1/10) X201 (1/2)

33.75MHz IC202 1 CPU IC_211_2_SO, XIC_211_2_SCK SPDA, SPCK V1, V2, V3A, V3B, V4, 2 CLOCK 3 GEAR_ON Y13 (4/10, 5/10) V5A, V5B, V6 - V10 GENERATOR 5 GEN_SYS_CLK Y12 (6/10)

FOCUS RESET SENSOR

IC_211_3_SO, XIC_211_3_SCK, XCS_FE

VST

2 12 D6 5 17

VHLD

D5 XDD_SYS_RST 26 VSUB C1 39 C4 VSUB_CONT IC_211_2_SO,27 38 XIC_211_2_SCK RL-071/078 Q301 E7 BOARD (1/2) V8 XCS_AUDIOVSUB_CONT_PRE, E4 CN707 CN101 Q302 VSUB_CONT_POST (1/2) (1/2) IC_211_AUIN MIC_SIG 1 MIC_SIGAF8 E6 B6 1 MIC901 IC401 IC603XLENS_DRIVER_PS LENS DRIVE D4 H11 IC_211_AUOUTAE8 E5 AUDIO AMP SP± SP901 (2/10) (7/10) SPEAKER CN402 MC-176 BOARD ND(±) ND_± IRIS MOTOR IRIS_M_IN, IRIS_M_BRK_2B DRIVER (1/2) CN710 CN101 (1/2) (1/2) AU_LINE_OUT 7 A_OUT_L F_MOTOR_A, F_MOTOR_A(-), D1 24 16 F_MOTOR_B, F_MOTOR_B(-) FOCUS_A, A, B, B FOCUS MOTOR FC_DIR_A, FC_DIR_B, FC_EN_A

DRIVER

T8 VIDEO_AMP_ON 4 IC602 VIDEO AMP V_LINE_OUT 5 V_OUT3 5 26 20 Z_DC_MOTOR(±) ZOOM_A, ZOOM_A- ZOOM ZM_DIR_A, ZM_EN_A, ZM_BRK_B MOTOR (7/10)

DRIVER

Q242 - Q244 Q241 SHUTTER IC_211_CVOUT IC_211_YOUT HDY3HD Y CN102SHUTTER(±) SHUTTER_± MSHUT_DIR, MSHUT_EN AB13 28 24 MOTOR VOUT_1 IC_211_PBOUT HD Pb 14 HD Pb (1/2) DRIVER AF12 BUFFER CLAMP 17 4 MULTIVOUT_2 IC_211_PROUT HD Pr AC12 15 16 HD Pr 2 CONNECTOR F_PI_SENS_OUT FC_SENS ZOOM ZOOM 22 Y10RESET XFC_RST_LED 23 XFC_RST_LED M8 XHD_EN FG V7SENSOR Z_PI_SENS_OUT ZM_SENS_1ST 41 AD26 10, 9 Z_BOX2_PI_SENS_Col, Z_BOX1_PI_SENS_Col ZM_DC_FG_1A, ZM_DC_FG_1B USB_DP, USB_DM USB_DP, USB_DM XZM_FG_LED 26 XZM_FG_LED L8 USB_VBUS 12 USB_VBUS 19 6 LENS_ID LENS_ID 44 D9 2 OVERALL (2/2) CN704 LENS TEMP THERM LENS_TEMP40 AE3 (PAGE 3-2) XMS_IN SENSOR 6

MEMORY STICK OPTICAL IMAGE MSX_D0 - MSX_D3, MSX_CLK, MSX_BS DUO STABILIZER OIS TEMP THERM 4 TZ_HALL_TEMPSENSOR AF3

SE501 YAW M YAW± SWAOUTMOTOR J5 13 21 YAWSENSOR YAW_HALL_BIAS±, IC506 HALL YAW_HALL_± ELEMENT DATA, CLK PITCH/YAWSENSOR

AMP

(3/10) SE502 PITCH M PITCH± IC503 SWBOUTMOTOR G5 10 1 PITCHSENSOR

OPTICAL

PITCH_HALL_BIAS±, IMAGE HALL PITCH_HALL± STABILIZATION C9 CA_FD ELEMENT DRIVE A7 XDD_SYS_RST XDD_SYS_RST(3/10) 1

A : VIDEO SIGNAL

IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK OVERALL (2/2) (PAGE 3-2) A : AUDIO SIGNAL A3 CLK_IC_503

A : VIDEO/AUDIO SIGNAL

W13 A5 XCS_IC_503 U8 A6 XIC_211_IC_503_RST H10 3-1 1, 3, 6-12, 14-16 31, 32, 21, 22 2, 3, 5, 6 11 - 8 17 - 20 15 - 12 24, 28 48 - 45 33 - 30 38 - 35 50, 49 J3, J2, H2, J4 B1, D1 G6, J8, J9, J7 B10, D10 11, 13-16, 18-24 30, 28, 31, 27 A4, B4, B5 D6, D5 25, 24 F4, F3 B4, B5 D6, E6, B7, C6 D2, B1 D4, D7, E4, F4, K6, K5, J6, J5 G4-G7, H4-H7 D1, E1-E3, F1-F3 G1, E4 A2, C4, B2 D5, A6, B6, C5 D3, F1 C3, C2, B3 G1-G3, H1-H3, J1 Y11, W11 R8, AE25 AB23, AA23, AC25 W18, AB26, W17 Y18, Y17 R7, AF25 C25, D19, V19 AB19-AB21, AC18-AC21, AE18-AE21, AF19-AF21 A13 - A15, D17, B19, E17, A19, B13 - B15 Y1, AA1 E18, B23 B18, D18, B17 E16, A18, D16, A17 F3, E3 A5, A2 2 - 5, 7, 8 21, 22 35, 34 11 - 13 3 - 10 10, 12, + 3-2. OVERALL BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

RL-071/078 BOARD (2/2) SY-173 BOARD (2/2) MC-176 BOARD

CN101 CN707 (2/2) (2/2) (2/2) S101 8 XAE_LOCK_SW XAE_LOCK_SW CN710 CN1018 7 XSHUTTER_SW XSHUT_SW (2/2) (2/2)(SHUTTER) 7 XPWR_ON XPOWER_ON 27 XPOWER_ON47S102 3 XPWR_ON XPWR_ON XPWR_ON ACV_UNREG 18 - 20 ACV_UNREG POWER 3 B8 UNREGXDIRECT_PB B7 ST_UNREG Q004, XACV_DET 24 XACV_DET7 19 D101 4 X_PWR_LED XPWR_LED Q013 (POWER) 4 CAM_12V D002 CAM_-7.5V CHARGE_V 21 - 23 CHARGE_V TI_5.0V MAX_5.0V

SW-494 BOARD IC001D_3.0V DC/DC CN102

A_3.0V CONVERTER (2/2) S003 CN001 CN708 J5 8 XDIRECT_PB XDIRECT_PB X101 DDR_1.8V (9/10)

MULTI

5 CONNECTORN 32.768kHz D_1.8V J4 D_1.2V S001, S002, BL_H S004 - S010 FUNCTION 6, 7 KEY_AD1, 2 KEY_AD_1, 2

KEY

D003 Q101 IC101 XACV_INS011 K8 MODE 12, 11 MODE_DIAL1, 2 MODE_DIAL1, 2 2 XMS_IN

FRONT

C6 CONTROL G9 XACC_IN XACC_IN 1 XACC_IN DIAL 30(8/10) UART Rx, IC_211_1_UI, IC_211_1_UO UART Rx, UART TX 25, 26 OVERALL (1/2) UART TxUSB_VBUS D001 (PAGE 3-1) D8 AE/AF LOCK/ 4 XAE_LOCK_LED XAE_LOCK_LED SELF-TIMER 9 D002 FLASH CHARGING/ 5 XSTRB_LED 8 XSTRB_LED XPWR_OFF RECORD B9 G8 XIC_211_RST_REQ A1 W12 LCD901 (2/2) 1 VL_3V VL_3V XDD_SYS_RST BT001 12 3 IC102 5 D7 B4 AB18 LCD MODULE LITHIUM 2 BACK UP VCC 4 A9 BACKLIGHT BATTERY D101 (8/10) XCS_FRE2 A23 BL_H Q006 BATT_UNREG + BL_L 9 BL_L 4 BL_L BACKLIGHT BL_EN2 CONTROL F9 IC_211_0_SO,IC_211_0_SI, IC_211_1_SI, BT901 XIC_211_0_SCK IC_211_1_SO, BATTERY XIC_211_1_SCK, E4 BATT_SIG S TERMINAL XCS_IC_201, IC201 –

BATTERY AUTHENTICATION

IC106 D102 (6/10) 1 XDD_SYS_RSTRESET B2 (8/10) 1 XDD_SYS_RST IC211(2/2) OVERALL (1/2) IC_211_0_SO, IC_211_0_SI, XIC_211_0_SCK CPU (PAGE 3-1) (4/10, 5/10) XAE_LOCK_SW N19 XSHUT_SW R19 KEY_AD_1, 2 MODE_DIAL1, 2 XPWR_LED Y9 XAE_LOCK_LED W9

ST-160 BOARD XSTRB_LED W8

CN001 CN701 D002 XAF_LED 12 AFLED_CONT SELF-TIMER/ 12 AF LED G15 AF ILLUMINATOR CONTROL T001 Q704 D001 XE_A(H) D70632ST_UNREG (MS ACCESS) H841

TRIGGER FLASH

UNIT TRIG_GND C901 CHARGING STRB_CHG 8 STRB_CHG CAPACITOR 15 IC001 10 8 V2 XE_K(L) XSTRB_FULL 9 XSTRB_FULLFLASH99H9 CONTROL, STB_CHG_CNT 5 STB_CHG_CNT6 5 H15

CHARGE

Q001 CONTROL STRB_ON 4 STRB_ON1 FLASH744Y16

DRIVE DSC-W80/W85_L2

3-2 1, 2 1, 2 7, 6 D1, D2, E1 AB7, AE6 AC8, AF6 H17, A24, G17 G18, B24, H18, W20 D26, G19 D5, C5, B5, B1 6, 5 8 - 10 11 -13 15, 9 17, 21 23, 25, 3-3. POWER BLOCK DIAGRAM (1/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.

MC-176 BOARD SY-173 BOARD (1/2)

F001 CN101 CN710 Q706 CN704 ACV_UNREG 18-20 ACV_UNREG F002 MS_VCC IC001 B+ SWITCH 9

MEMORY STICK

DC/DC CONVERTER DUO Q004, 013 (9/10) F XACV_DET 24 XACV_DET MS_PWR_ON 19 7 28 GD CN102 POWER (2/2)45 BATT ST_UNREG MULTI D002D003 (PAGE 3-4) CONNECTOR L009 D_1.2V 13 PVSD LXSD 16 CHARGE_V 21-23 CHARGE_V BATT_UNREG DDC1P2_ENONSD 15 D007 CAM_12V 29 PVBST LXBST 31 L004 XPOWER_ON 27 XPOWER_ON SWBST 3074ONBST 22 D010 CAM_-7.5V LXINV 21 PVINV 20 CAMDD_EN ONINV 1 XACV_IN BT901

BATTERY

TERMINAL IC201 BATTERY L001 A_3.0V + BATT_UNREG AUTHENTICATION PVM 4 L005 D_3.0V (6/10) E LXM 5 DDC2P9_EN BATT_SIG IC_211_1_SI POWER (2/2) ONM 3 P144_SOA0 D5 S E4 TXRX IC_211_1_SO (PAGE 3-4) P143_SIA0 C5 D006 BL_H XIC_211_1_SCK 35 PVLED LXLED 33 P142_XSCKA0 B5 L003 Q006 XCS_IC_201 SWLED 34– P120_INTP0 B1 BL_LFBLLED 37 BACKLIGHT BL_EN1 CONTROL ONLED 36 D_3.0V BL_EN2 B2 XRESET D011 L007 Q003 MAX_5.0V 47 LXSU SU 43 B+ SWITCH IC106 PVSU 44 DDC5PSW_EN VSU_EN RESET (8/10) ONSU 46

A XDD_SYS_RST D102

1 OUT Vdd 4 POWER (2/2) G (PAGE 3-4) L0069 PVAFE LXAFE 8 DDC1P8_EN IC101 ONAFE 10 POWER (2/2)(PAGE 3-4) FRONT CONTROL (8/10) Q014 B+ SWITCH BATT_SENS H8 D_3.0V DDCPV_EN DDC2P9_AD H7 A9 CS D_1.8VDDC1P8_AD J7 B4 XSYS_RST BACK_UP_VCC IC002 5V REG(9/10) DDC1P2_EN L002 DDC1P2_EN D9 CAMDD_EN 9 SW TI_5.0V CAMDD_EN B2 6 VBAT VOUT 2DDC2P9_EN DDC2P9_EN E9 7 LBI EVER_PSB D_3.0V BL_EN1 1 EN PS 8 D_1.8V D_1.8V BL_EN1 F8 BL_EN2 BL_EN2 F9 DDC5PSW_EN DDC5PSW_EN F7 SW_1P8_EN Q007 VSU_EN 1.8V/3.0V

B XIC_211_RST_REQ VSU_EN J8 DISCHARGEA1 XRESET_REQ DDC1P8_EN 1.8V REG Q010, 012

XPWR_OFF DDC1P8_EN E8 IC003 B9 XPOWER_OFF DDCPV_EN (9/10) B+ SWITCHPOWER (2/2) DDCPV_EN C9 (PAGE 3-4) EVER_PSB DDR_1.8VEVER_PSB J9 B2 Vin Vout B1 SW_1P8_EN SW1P8_EN J1 Vcont LDO_1P8_EN

C XPWR_ON LDO1P8_EN H2 A2 BACK_UP_VCCB8 XPOWER_ON0 DISW1P8_EN

XDIRECT_PB DISW1P8_EN C2 LDO_1P8_EN POWER (2/2) B7 XPOWER_ON2 DISW2P9_EN DISW2P9_EN C1 DISW1P8_EN (PAGE 3-4) DISW2P9_EN VL_3V XRSTX D7 IC102 BACK UP VCC 1.2V_INT (8/10) DDC1P2_RESET C8 3 VBAT VOUT 6 EVER_3.0V 2 VCH VRO 8

D D101DDC2P9_EN 7 VIN IC007

POWER (2/2) 5 XRESET VOLTAGE (PAGE 3-4) 4 CS DETECT (9/10) Vin41Vout Vsen 3

DSC-W80/W85_L2

3-3 17, 21 23, 25 8-10 11-13 XPWR_ON, 3-4. POWER BLOCK DIAGRAM (2/2) ( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located. LCD901

SY-173 BOARD (2/2) LCD MODULE

CN713 D_1.8V FB702 VDDD

VDD

D_3.0V L701

PVDD

18 2.5INCH IC501 COLOR 2.8V REG XDD_SYS_RST RESET Z

LCD

(3/10) IC506 A_3.0V PITCH/YAW B2 Vin Vout B1 SENSOR AMP SW-494 BOARD BACKLIGHT Vcont (3/10) CN708 CN001 IC502 A2 BL_H BL_H 10 BL_H3 1.5V REG BL_L BL_L 9 BL_L (3/10) SE502 4VL_3V VL_3V 1 PITCH 12 BT001 D_1.8V B2 Vin Vout B1 SENSOR LITHIUM IC503 BATTERY OPTICAL SE501 D_3.0V IMAGE YAW D001 MAX_5.0V STABILIZATION SENSOR D_3.0V 3 AE/AF LOCK/ DRIVE 10 SELF-TIMER (3/10)

A S003 D002XDD_SYS_RST XDIRECT_PB 85 FLASH CHARGING/

ST_UNREG A7 RESET_N RECORD POWER (1/2) XIC_211_IC_503_RST A6 XDL D_1.2V (PAGE 3-3) C XDD_SYS_RST CAM_12V POWER (1/2) RL-071/078 BOARD (PAGE 3-3) CAM_-7.5V CN707 CN101 S102 XPWR_ON33POWER A_3.0V D_1.8V D_1.8V D_3.0V 55 D101 D_3.0V D_3.0V D_3.0V (POWER) TI_5.0V TI_5.0V BL_H MAX_5.0V MAX_5.0V BL_L A_3.0V A_3.0V ST-160 BOARD

G T001

MAX_5.0V CN701 CN001IC603 POWER (1/2) AU_AVCC ST_UNREG ST_UNREG 1, 2 L001 D001 FLASH (PAGE 3-3) B2 Vin Vout B1 AUDIO AMP (7/10) UNITTI_5.0V TI_5.0V 3 IC601 H10 GPE_09 R601 Q710 TI_5.0V 2.9V REG AB18 XRESET IC602 (7/10) MAX_5.0V AF LED AF_5.0V 11VIDEO AMP D601 DRIVE (7/10) D002 IC001 SELF-TIMER/ FLASH CONTROL, A_3.0V R723 AF ILLUMINATOR CHARGE CONTROL D_1.8V D706 R253 (MS ACCESS) Q704 AF LED XAF_LED 12 DDR_1.8V CONTROL L241 VL_3V AFLED_CONTD_3.0V TPU2_OUT G15

CD-701 FLEXIBLE

IC305 12V REG(1/10) BOARD D_1.2V R254 L201 CN301IC202 DDR_1.8V D_3.0V CAM_12V FB313 L301 CAM_12V D_1.8V D_1.8V CLOCK 5 Vin Vout41IC003 IC211 GENERATOR (6/10) FB282 CPU CAM_-7.5V L302 7M L211 CAM_-7.5V CCD IMAGER (4/10) 36 FB283 (5/10) CAM_3.2V (6/10) FB307 3.2V REG Q303IC306 (1/10) -7.5V DISCHARGE IC004 TI_5.0V CAM_3.2V B2 Vin Vout B1 BUFFER Vcont A2

D DDC2P9_EN FB310

POWER (1/2) D_3.0V FB311B XIC_211_RST_REQ W12 XRESET_REQ (PAGE 3-3) XPWR_OFF IC304 LENS BLOCK POWER (1/2) G8 GPE_00 (PAGE 3-3) CCD SIGNAL IC308 PROCESS, Q401 CN402R402 ZOOM XACV_IN TIMING GENERATOR Z_PI_SENS_Vcc K8 GPE_05 2.8V REG (1/10) B+ SWITCH 42 RESET (1/10) SENSOR

E IC_211_1_SI G18 SIO1_RXD

IC_211_1_SO 6 Vin Vout 4 B24 SIO1_TXD R412 Z_BOX1_PI_SENS_VccPOWER (1/2) XIC_211_1_SCK 27 ZOOM (PAGE 3-3) H18 SIO1_SCK Z_BOX2_PI_SENS_Vcc XCS_IC_201 25 FG W20 GPS_04 Q3052.8V/3.2V R411

DISCHARGE

R401 F_PI_SENS_Vcc FOCUS

F 21 RESETMS_PWR_ON

T7 GPE_15 GPE_03 J8 XZM_RST_LED XDD_SYS_RST SENSORC1 RESET POWER (1/2) (PAGE 3-3) D_3.0V MAX_5.0V IC401 A_3.0V LENS DRIVE (2/10)

DSC-W80/W85_L2

3-4 1, 2 XZM_RST_LED, 4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM 12 1 CN001 Note: CN001 is no mount. (Direct solder) BT001 LITHIUM BATTERY MIC901

SW-494 MICROPHONE BLOCK BOARD

FLASH UNIT

RL-071/078 BOARD

LCD901 LCD MODULE CN101 Note: CN101 is no mount. 1 8 (Direct solder) 2.5INCH C901 BACKLIGHT COLOR CHARGING CAPACITOR LCD 1 CN001 11 2 12 LEVEL3

ST-160 BOARD FLEXIBLE FLAT CABLE CD-701 FLEXIBLE BOARD(FFC-094)

Note: CN701 is no mount. (Direct solder) 1 12CN701 39 1 CN707 BT901 FLEXIBLE FLAT CABLE CN708 38 CN713281BATTERY12 1 39 (FFC-093) TERMINALRED

WHT BLK

IC003 (Not supplied) CN704 MEMORY STICK

CONNECTOR

IC211 (Not supplied)

LENS BLOCK

1 30 CN710

LEVEL3 LEVEL3 SY-173 BOARD SY-173 BOARD

(SIDE A) SP901 (SIDE B)SPEAKER

MC-176 BOARD (SIDE A)

30 1 26 2 CN101 Note: CN101 is no mount. 25 1 (Direct solder) 28 27

MC-176 BOARD (SIDE B)

CN102 MULTI CONNECTOR 4-1 FRAME 10 1 FLEXIBLE FLAT CABLE (FFC-092) 12 11 FLEXIBLE FLAT CABLE (FFC-095)

BLK RED

2 CN402 50 2 CN301 38 1 51 1 39

BLK RED LOCK

, 4-2. SCHEMATIC DIAGRAMS Link MC-176 BOARD (MULTI CONNECTOR) ST-160 BOARD (FLASH DRIVE) SW-494 BOARD (CONTROL SWITCH) RL-071/078 BOARD (CONTROL SWITCH, MIC) COMMON NOTE FOR SCHEMATIC DIAGRAMS, 4-2. SCHEMATIC DIAGRAMS 4-2. SCHEMATIC DIAGRAMS THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS (In addition to this, the necessary note is printed in each block) (For schematic diagrams) 1. Connection • All capacitors are in µF unless otherwise noted. pF : µ µ Pattern boxF. 50 V or less are not indicated except for electrolytics Color bar chart and tantalums. Pattern box PTB-450 For PTB-450: • Chip resistors are 1/10 W unless otherwise noted. J-6082-200-A J-6020-250-A kΩ=1000 Ω or, MΩ=1000 kΩ. Small pattern box For PTB-1450: • Caution when replacing chip parts. PTB-1450 J-6082-559-A New parts must be attached after removal of chip. J-6082-557-A Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. L = 24 cm (PTB-450) • Some chip part will be indicated as follows. L = 11 cm (PTB-1450) Example C541 L452 22U 10UH Pattern box Front of the lens TA A 2520 L Camera Kinds of capacitor External dimensions (mm) Case size • Constants of resistors, capacitors, ICs and etc with XX indicate that they are not used. In such cases, the unused circuits may be indicated. 2. Adjust the distance so that the output waveform of • Parts with ★ differ according to the model/destination. Fig. a and the Fig. b can be obtain. Refer to the mount table for each function.

H

• All variable and adjustable resistors have characteristic curve B, unless otherwise noted. • Signal name XEDIT → EDIT PB/XREC → PB/REC • 2: non flammable resistor • 5: fusible resistor • C: panel designation • A: B+ Line • B: B– LineABA=BBA• J : IN/OUT direction of (+,–) B LINE. Fig. a (Video output terminal output waveform) • C: adjustment for repair. • A: not use circuit (Measuring conditions voltage and waveform) Electronic beam scanning frame • Voltages and waveforms are measured between the measurement points and ground when camera shoots CRT picture frame color bar chart of pattern box. They are reference values and reference waveforms. (VOM of DC 10 MΩ input impedance is used) • Voltage values change depending upon input impedance of VOM used.) Fig.b (Picture on monitor TV) Precautions for Replacement of Imager When indicating parts by reference number, please • If the imager has been replaced, carry out all the adjustments include the board name. for the camera section. The components identified by mark 0 or dotted line with • As the imager may be damaged by static electricity from mark 0 are critical for safety. its structure, handle it carefully like for the MOS IC. Replace only with part number specified. In addition, ensure that the receiver is not covered with dusts nor exposed to strong light. Les composants identifiés par une marque 0 sont critiques pour la sécurité. Ne les remplacer que par une pièce portant le numéro spécifie. 4-3 Yellow Cyan Green White Magenta Red Blue, Schematic diagrams of the CD-701 flexible and SY-173 boards are not shown. Pages from 4-5 to 4-15 are not shown. DSC-W80/W85_L2, 12345678910 11 12

A MC-176 BOARD MULTI CONNECTOR XX MARK:NO MOUNT Note:CN102 (multi connector) is not supplied,

CN101 XX but this is included in MC-176 complete board.

B ACV_GND 30

ACV_GND 29 ACV_GND 28 XPOWER_ON 27 UART TX 26 UART Rx 25 XACV_DET 24 CHARGE_V 23 CHARGE_V 22

C CHARGE_V 21

ACV_UNREG 20 ACV_UNREG 19 ACV_UNREG 18

SY-173

REG_GND 17 (10/10) CN710 HD Pr 16 CN102 Through the REG_GND 15 (MULTI CONNECTOR) flexible flat cable To AV/USB multi cable

D (FFC-095) HD Pb 14Page 4-15 REG_GND 13

of Level 3 USB_VBUS 12 2 HD Pr ACV_GND 1 USB_GND 11 4 HD Pb ACV_GND 3 USB_DP 10 6 USB_VBUS ACV_GND 5 USB_DM98USB_GND XPOWER_ON 7 USB_GND 8 10 USB_DP UART Tx 9 AU_LINE_OUT 7 12 USB_DM A_GND 6 14 USB_GND

E V_LINE_OUT 5 16 A_OUT_L UART Rx 15

V_GND 4 18 A_GND CHARGE_V 17 HDY320 V_OUT XACV_DET 19 REG_GND 2 22 V_GND CHARGE_V 21 XACC_IN 1 24 HD Y ACV_UNREG 23 26 XACC_IN ACV_UNREG 25

F Note:CN101 is not mounted.Flexible flat cable (FFC-095) is

soldered to this location instead. LND102 STATIC_GND

This FFC-095 is not supplied, but this is included in MC-176 complete board. G DSC-W80/W85_L2

4-16 MC-176, • Refer to page 4-3 for mark 0. 12345678910 11 12

A SW-494 BOARD CONTROL SWITCH XX MARK:NO MOUNT Note:CN001 is not mounted. Flexible flat cable

(FFC-092) is soldered to this location instead.

B

CN001 XX BT001

LITHIUM

VL_3V 1 BATTERY REG_GND 2 D001 D_3.0V 3 SML-510MWT86S (AE/AF LOCK/SELF-TIMER)

SY-173 XAE_LOCK_LED 4 D002

(10/10) XSTRB_LED 5 SML-310YTT86 R001 RB0032200 2200 CN708 (FLASH CHARGING/RECORD) 1 2 KEY_AD1 6

C Through the 3 4flexible flat cable 5 6KEY_AD2 7

(FFC-092) 7 8 Page 4-15 XDIRECT_PB 8 of Level 3 BL_L 9 BL_H 10 MODE_DIAL2 112121212121MODE_DIAL1 124343434343LCD901(2/2) S001 S004 S006 S008 S010

D 4 5BACKLIGHT

LND002 D005 (SELF-TIMER) (FLASH) (DISP) R005 (MACRO) (SET) XX 2200 BL_L321BL_H LND0031234D00356LND001 D004XX XX78STATIC_GND RB001 STATIC_GND LND004

E21212121

43434343S002 S005 S007 S009 W (ZOOM) T MENU HOME

AUTO

15 3

AUTO

16 HIGH SENS SOFT SNAP

F 6TWILIGHT PORTRAIT 1 21734

COM TWILIGHT568782LANDSCAPE R006 9 2200COM RB002LANDSCAPE 2200 BEACH2117 SNOW MOVIE4318 13 PROGRAM AUTO S003

G R007S011 2200

(MODE DIAL)

Note:S011(mode dial) is not supplied, but this is

included in SW-494 complete board.

H DSC-W80/W85_L2

4-17 SW-494, • Refer to page 4-3 for mark 0. 12345678910 11 12

A ST-160 BOARD FLASH DRIVE XX MARK:NO MOUNT NO MARK:REC/PB MODE B L001 T001 D001CN001 12P 2.2uH MA2YF8000LS0 LND019

ST_UNREG123XE_A(H) LND015 ST_UNREG 2 C007 R006 220p 4700 CHARGE+ TI_5.0V314R004 LND017

SY-173 STRB_ON 4 C901 1M

49u TRIGGER(10/10) STB_CHG_CNT 5 315V FLASH CN701 C001 TRIG_GND UNIT Through the REG_GND 6 22u

CHARGING

LND016 D003 CAPACITOR C004 LND018 flexible flat cable REG_GND 7 RB520S-40TE61 CHARGE- 0.047u (FFC-093) 250V LND020

C Page 4-15 STRB_CHG 8 262 XE_K(L)

of Level 3 XSTRB_FULL951NC 1062AF_5.0V 1173XAF_LED 12 4.1 R0020841M 17 16 15 14 13 Q001 CY25BAJ-8F-T23-G02 FLASH DRIVE

D

C005 C002 XX 1u SW PGND 4.143IC001 R00352SW PGND 100FLASH CONTROL, 6 1 R0055 CHARGE CONTROL 0 XX D002 VCC IC001 CHG CL-360S-TD4-X-TL TPS65552RGTR SELF-TIMER/ 3.1 AF ILLUMINATOR F_ON XFULL C006

E XX

567800CL001

F

4-18 ST-1604321N.C HGND I_PEAK N.C G_IGBT VBATT N.C N.C N.C 9 10 11 12, 123456

A RL-071/078 BOARD Note:In this set, either RL-071 or RL-078 board is used. CONTROL SWITCH,MIC All mounted parts and schematic diagramare common to both RL boards. MIC901 MICROPHONE

XX MARK:NO MOUNT BLOCKLND101 MIC_GND MIC_SIG LND102

B

2 1 S102

POWER

4 3 CN101 XX MIC_SIG 1 SY-173 MIC_GND 2 D101SML-412MWT86 (10/10) XPWR_ON 3 (POWER) CN707 Through the X_PWR_LED 4C flexible flat cable D_3.0V 5 (FFC-094) Page 4-15 REG_GND 6 of Level 3 XSHUTTER_SW 7 S101 XAE_LOCK_SW 8 (SHUTTER) 6 5 C001 C002 0.047u 0.047u4213

D

Note:CN101 is not mounted. Flexible flat cable (FFC-094) is soldered to this location instead. LND103 STATIC_GND

E

LND104 STATIC_GND

DSC-W80/W85_L2

4-19 RL-071/078, 4-3. PRINTED WIRING BOARDS Link MC-176 BOARD ST-160 BOARD SW-494 BOARD RL-071/078 BOARD COMMON NOTE FOR PRINTED WIRING BOARDS MOUNTED PARTS LOCATION, 4-3. PRINTED WIRING BOARDS 4-3. PRINTED WIRING BOARDS THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS • : Uses unleaded solder. • Chip parts. • : Circuit board Transistor Diode : Flexible boardC6544565445333123Pattern from the side which enables seeing. : pattern of the rear sideBE123321123321212121654(The other layers’ patterns are not indicated) • Through hole is omitted. 1221324334654456• Circled numbers refer to waveforms. • There are a few cases that the part printed on diagram543345411221123321isn’t mounted in this model. 3 2 • C: panel designation414-21, Printed wiring boards of the CD-701 flexible and SY-173 boards are not shown. Pages from 4-23 to 4-25 are not shown.,

MC-176 (4 layers), SW-494 (2 layers)

: Uses unleaded solder.

MC-176 BOARD (SIDE A) MC-176 BOARD (SIDE B)

- MC-176 CN101 >EP GW< 30 1 28 262127 25 A LND102 05 CN102 1-871-499- 11 12 1-871-499- 11 1205 (MULTI CONNECTOR) Note: CN101 is not mounted. Flexible flat cable (FFC-095) is soldered to this location instead. Note: CN102 (multi connector) is not supplied, This FFC-095 is not supplied, but this is included in MC-176 complete board. but this is included in MC-176 complete board.

SW-494 BOARD (SIDE A) SW-494 BOARD (SIDE B)

K A D001 D001 – (AE/AF LOCK/SELF-TIMER) CN001KA+ D002 12 1

A W (ZOOM) T A

D0023131(FLASH CHARGING/RECORD) S002 S005 Note: CN001 is not mounted. Flexible flat cable (FFC-092) 4242is soldered to this location instead. 2817BL-H LND003 RB001 TO LCD901 BT001 (BACKLIGHT) LITHIUM BL-L BATTERY LND002 B

B N

Note: S011 (mode dial) is not supplied, but this is included in SW-494 complete board. S011 (MODE DIAL) RB002 MENU 7 182v(DISP) C

C 2 4RB003

2817S006b13B(MACRO) z (SET) (FLASH) D005 R00154CAUTION3113

D Danger of explosion if battery is incorrectly replaced. D

A K S001 Replace only with the same or equivalent type. D003421-871-501- V LND001 LND004 (SELF TIMER) 11 12 1-871-501- 11 12

HOME

055432105123454-26 MC-176, SW-49424R0052424S009 S007 S00324131313S008 R0071324R006 S010 10 11 12 2 13 141318 15 D004 9 S0113AK3117 16 S00487165442BT001,

ST-160 (4 layers), RL-071/078 (2 layers)

: Uses unleaded solder.

ST-160 BOARD (SIDE A) RL-071 BOARD (SIDE A)

FLASH UNIT XE_K (L) XE_A (H) LND103 C004 TRIG_GND TRIGGER

A LND016

LND018 LND017 D101 C901KAA34CHARGING K D001 T001 (POWER) CAPACITOR21LND015 LND020 1-871-502- 12 LND019 C005 CL001 S101 S102 05 (SHUTTER) POWER1 11 C001 CN001

B 1-871-500-2 12 11L001

05123MIC901

MICROPHONE BLOCK RL-071 BOARD (SIDE B) ST-160 BOARD (SIDE B)

LND102 LND101

B ST-160 B

8 1 CN101 SELF-TIMER/ AF ILLUMINATOR 1-871-502- 12 LND104

A R003 1-871-500- 11R002 5 05

8 121 Q0 0 Note: CN101 is not mounted. Flexible flat cable (FFC-094) is soldered to this location instead. 05 Note: In this set, either RL-071 or RL-078 board is used.123All mounted parts and schematic diagram are common to both RL boards.

RL-078 BOARD (SIDE A)

LND103 1-874-109- D101KA(POWER) S102 1-874-109- 11S101

POWER

05 (SHUTTER) A MIC901

MICROPHONE BLOCK RL-078 BOARD (SIDE B)

LND102LND10181CN101 1-874-109- 11 LND104 Note: CN101 is not mounted. Flexible flat cable (FFC-094) is soldered to this location instead. 4-27 ST-160, RL-071/078 R004 D003 C002AKC007 R00641517 16 IC001 8 139 12 C006 R00564D002 - 1 3 >EP GW< C001 >EP GW< C00112125656S101 S1014343C002 C0023131S102 S1024242

RL-078

>EP GW< RL-078 B 1-874 -109- B R RL-071 B 1-871 -502- B R + + >EP GW<, Mounted parts location of the SY-171 board is not shown. Pages 4-29 and 4-30 are not shown., 4-3. PRINTED WIRING BOARDS 4-4. MOUNTED PARTS LOCATION no mark : side A * mark : side B SW-494 BOARD ST-160 BOARD * BT001 A-2 C001 A-1 C002 A-2 * CN001 A-3 C004 A-1 C007 A-2 D001 A-1 D002 A-1 CN001 B-2 R001 D-5 D001 A-1 R005 C-4 * D002 A-3 R006 C-5 D003 A-2 R007 B-4 IC001 A-2 RB001 A-5 RB002 C-4 L001 B-1 RB003 C-4 * Q001 A-1 S001 D-5 S002 A-4 * R002 A-1 S003 B-4 * R003 A-1 S004 D-5 R004 A-1 S005 A-5 R006 A-2 S006 C-5 S007 C-4 T001 A-1 S008 D-4 S009 D-4 S010 D-5 S011 B-5 4-31E SW-494, ST-160,

NOTE

5. REPAIR PARTS LIST NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.

Link EXPLODED VIEWS

ABCCABINET SECTION MAIN BOARD SECTION LCD/BT HOLDER SECTION

D

LENS SECTION

Link ELECTRICAL PARTS LIST ACCESSORIES

MC-176 BOARD B ST-160 BOARD C SW-494 BOARD C RL-071/078 BOARD B, 5. REPAIR PARTS LIST 5. REPAIR PARTS LIST NOTE: • -XX, -X mean standardized parts, so they may have some differences from When indicating parts by reference number, the original one. please include the board name. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. The components identified by mark 0 or • The mechanical parts with no reference number in the exploded views are not dotted line with mark 0 are critical for safety. supplied. Replace only with part number specified. • Due to standardization, replacements in the parts list may be different from Les composants identifiés par une marque the parts specified in the diagrams or the components used on the set. 0 sont critiques pour la sécurité. • CAPACITORS: Ne les remplacer que par une pièce portant le numéro spécifié. uF: µF • COILS uH: µH • RESISTORS • Color Indication of Appearance Parts All resistors are in ohms. Example: METAL: metal-film resistor (SILVER) : Cabinet’s Color METAL OXIDE: Metal Oxide-film resistor (Silver) : Parts Color F: nonflammable • SEMICONDUCTORS In each case, u: µ, for example: uA...: µA... , uPA... , µPA... , uPB... , µPB... , µPC... , µPC... , uPD..., µPD... • Abbreviation AR : Argentine model AUS : Australian model BR : Brazilian model CH : Chinese model CND : Canadian model EE : East European model HK : Hong Kong model J : Japanese model JE : Tourist model KR : Korea model NE : North European model TW : Taiwan model 5-1, 5. REPAIR PARTS LIST 5-1. EXPLODED VIEWS DISASSEMBLY HARDWARE LIST 5-1-1. CABINET SECTION45#6576#65 #65 #65 #65 Main Board Section (See Page 5-3) #65 3 Ref. No. Part No. Description Ref. No. Part No. Description 1 X-2177-050-1 CABINET (FRONT) ASSY (W80: SILVER) 4 X-2177-063-1 CABINET (REAR) ASSY (W80: WHITE) 1 X-2177-051-1 CABINET (FRONT) ASSY (W80: BLACK/W85) 4 X-2177-064-1 CABINET (REAR) ASSY (W80: PINK) 1 X-2177-052-1 CABINET (FRONT) ASSY (W80: WHITE) 1 X-2177-053-1 CABINET (FRONT) ASSY (W80: PINK) 4 X-2177-065-1 CABINET (REAR) ASSY (W85) * 2 3-197-910-01 SHEET, SY ELECTROSTATIC 5 3-099-626-01 SHEET, LCD WINDOW ADHESIVE 6 3-099-624-01 WINDOW, LCD 3 3-099-623-01 CABINET, SIDE 7 3-099-625-01 PLATE, MODE 4 X-2177-061-1 CABINET (REAR) ASSY (W80: SILVER) #65 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P2 (Silver) 4 X-2177-062-1 CABINET (REAR) ASSY (W80: BLACK) 5-2, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

5-1-2. MAIN BOARD SECTION ns: not supplied 59 #65 LCD/BT Holder Section (See Page 5-4) 56 (Note 1) ns MIC901 54 55 ns 53 (FFC-093) 61 #5 62 65 ns 63 #5 64 66 SY-17 #303 #3 SP901 Lens Section (including IC003 (CCD imager) and 51 (See Page 5-5) CD-701 flexible complete board) (Note 2) Note 1: In this set, either RL-071 or RL-078 board is used. Note 2: Be sure to read “Precuations for Replacement of All mounted parts and schematic diagram are com- Imager” of level 3 on page 4-3. mon to both RL boards. Ref. No. Part No. Description Ref. No. Part No. Description 51 A-1253-161-A SY-173 BOARD, COMPLETE (SERVICE) 65 3-099-632-01 CABINET BOTTOM (W80: SILVER) 52 3-099-637-01 LABEL, FUSE 65 3-099-632-11 CABINET BOTTOM (W80: BLACK/W85) * 53 3-099-634-01 SHEET, ST INSULATING 65 3-099-632-21 CABINET BOTTOM (W80: WHITE) * 54 3-099-636-01 SHEET, RL INSULATING 65 3-099-632-31 CABINET BOTTOM (W80: PINK) 55 3-099-620-01 RETAINER, RELEASE 66 3-113-705-01 SHEET (PLUS), CD RADIATION 56 A-1246-054-A RL-071 BOARD, COMPLETE (Note 1) 68 A-1253-768-A CCD BLOCK ASSY (including IC003 56 A-1271-235-A RL-078 BOARD, COMPLETE (Note 1) (CCD IMAGER) and CD-701 flexible complete 57 1-833-618-11 CABLE, FLEXIBLE FLAT (FFC-094) board) (Note 2) 58 X-2177-054-1 RELEASE ASSY MIC901 1-542-721-11 MICROPHONE BLOCK 59 3-099-621-01 CABINET, UPPER SP901 1-826-614-21 LOUD SPEAKER (1.0CM) #3 2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red) 60 3-099-622-01 SHAFT, STRAP #5 3-080-204-01 SCREW, TAPPING, P2 (Black) 61 A-1246-051-A MC-176 BOARD, COMPLETE * 62 3-099-639-01 SHEET, MC RADIATION #30 3-086-156-11 SCREW B1.2 (White) * 63 3-099-629-01 RETAINER, MULTI #65 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P2 (Silver) * 64 3-099-635-01 SHEET, MC INSULATING 5-3, 5. REPAIR PARTS LIST

DISASSEMBLY HARDWARE LIST

5-1-3. LCD/BT HOLDER SECTION 111 ns: not supplied 110 109 #5 105 BT001 LCD901 ns ! : BT001 (BATTERY, LITHIUM #65 SECONDARY) Board on the mount position. (See page 4-26) C901 ns 101 BT901 113 (Note) Note: Refer to HELP “Installation method of battery termi- nal board” when changing the service terminal (BT).

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • Refer to page 5-1 for mark 0. Ref. No. Part No. Description Ref. No. Part No. Description 101 A-1246-052-A ST-160 BOARD, COMPLETE 111 1-833-616-11 CABLE, FLEXIBLE FLAT (FFC-092) 0102 1-480-014-11 FLASH UNIT * 112 3-198-159-02 SHEET, BT TERMINAL * 103 3-113-323-01 LABEL, MS CAUTION 113 X-2177-056-1 HOLDER ASSY, BT 104 3-099-631-01 SCREW, TRIPOD 0BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY 105 3-099-627-01 FRAME, MAIN BT901 A-1257-452-A TERMINAL, SERVICE (BT) (Note) 106 3-099-633-01 SHEET, LC FLEXIBLE 0*C901 1-114-309-11 ELECT 49uF 315V * 107 3-100-059-01 SHEET, LC FLEXIBLE ADHESIVE LCD901 1-802-379-11 LCD MODULE (LQ025A3DD01) * 108 3-197-557-01 SHEET, LIGHT INTERCEPTION #5 3-080-204-01 SCREW, TAPPING, P2 (Black) 109 A-1246-053-A SW-494 BOARD, COMPLETE #65 2-635-591-01 SCREW (M1.4), NEW TRUSTAR P2 (Silver) * 110 3-100-060-01 SHEET, SW 5-4, 5. REPAIR PARTS LIST

HARDWARE LIST

5-1-4. LENS SECTION ns: not supplied ns #30 ns #30 (Note 2) M901 (Note 2) 154 ns (Note 1) 157 153 (Note 2)ns (Note 1) (Note 1) 156 (Note 2) #30 Note 1: Be sure to read “Exchange method of barrier block” Note 2: Be sure to read “Exchange method of zoom gear on page 2-6. block” on page 2-8. Ref. No. Part No. Description Ref. No. Part No. Description 151 A-1231-924-A LSV-1160A (SERVICE) 156 2-689-850-01 SPRING, FG LEAF (Note 2) 152 2-689-851-01 RING (A), ORNAMENTAL (Note 1) 157 X-2177-203-1 GEAR (S), NARUTO (Note 2) 153 2-691-890-01 TAPE, BARRIER (Note 1) M901 1-479-864-11 GEAR BLOCK, ZOOM (1160) (Note 2) 154 A-1205-001-A BARRIER BLOCK ASSY (Note 1) #30 3-086-156-11 SCREW B1.2 (White) 155 2-689-849-01 SPRING, Z LEAF (Note 2) 5-5, Electrical parts list of the CD-701 board is not shown. Page 5-6 is not shown.,

MC-176 RL-071 RL-078 ST-160 SW-494

5-2. ELECTRICAL PARTS LIST Ref. No. Part No. Description Ref. No. Part No. Description A-1246-051-A MC-176 BOARD, COMPLETE < IC > *********************** (Flexible flat cable (FFC-095) and CN102 are not supplied, IC001 6-707-555-01 IC TPS65552RGTR but they are included in MC-176 complete board.) < COIL > (Not supplied) CABLE, FLEXIBLE FLAT (FFC-095) * L001 1-400-820-11 INDUCTOR 2.2uH < CONNECTOR > < TRANSISTOR > CN102 (Not supplied) CONNECTOR, MULTIPLE (SOCKET) (MULTI CONNECTOR) 0*Q001 6-551-676-01 TRANSISTOR CY25BAJ-8F-T13-G12 < RESISTOR > A-1246-054-A RL-071 BOARD, COMPLETE A-1271-235-A RL-078 BOARD, COMPLETE R002 1-218-989-11 RES-CHIP 1M 5% 1/16W ********************** R003 1-218-941-11 RES-CHIP 100 5% 1/16W 0R004 1-216-121-11 RES-CHIP 1M 5% 1/10W Note: In this set, either RL-071 or RL-078 board is used. R006 1-218-961-11 RES-CHIP 4.7K 5% 1/16W All mounted parts and schematic diagram are com- mon to both RL boards. < TRANSFORMER > 1-833-618-11 CABLE, FLEXIBLE FLAT (FFC-094) 0T001 1-445-108-21 TRANSFORMER, D.C-D.C CONVERTER < CAPACITOR > A-1246-053-A SW-494 BOARD, COMPLETE C001 1-119-923-11 CERAMIC CHIP 0.047uH 10% 10V ********************** C002 1-119-923-11 CERAMIC CHIP 0.047uH 10% 10V (S011 (mode dial) is not supplied, but this is included in SW-494 complete board.) < DIODE > 1-833-616-11 CABLE, FLEXIBLE FLAT (FFC-092) D101 6-501-030-01 DIODE SML-412MWT86 (POWER) * 3-100-060-01 SHEET, SW < MICROPHONE > < LITHIUM BATTERY > MIC901 1-542-721-11 MICROPHONE BLOCK 0BT001 1-756-710-11 LITHIUM RECHARGEABLE BATTERY < SWITCH > < DIODE > * S101 1-786-912-21 TACTILE SWITCH (SHUTTER) D001 8-719-075-29 DIODE SML-510MWT86S S102 1-786-885-42 SWITCH, TACTILE (POWER) (AE/AF LOCK/SELF-TIMER) D002 8-719-077-34 DIODE SML-310YTT86 (FLASH CHARGING/RECORD) A-1246-052-A ST-160 BOARD, COMPLETE ********************** < RESISTOR > 0 1-480-014-11 FLASH UNIT R001 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R005 1-218-957-11 RES-CHIP 2.2K 5% 1/16W < CAPACITOR > R006 1-218-957-11 RES-CHIP 2.2K 5% 1/16W R007 1-218-957-11 RES-CHIP 2.2K 5% 1/16W C001 1-100-611-91 CERAMIC CHIP 22uF 20% 6.3V C002 1-112-717-91 CERAMIC CHIP 1uF 10% 6.3V < COMPOSITION CIRCUIT BLOCK > 0C004 1-100-758-11 CERAMIC CHIP 0.047uF 10% 250V C007 1-164-933-11 CERAMIC CHIP 220PF 10% 50V RB001 1-234-376-11 RES, NETWORK 2.2K (1005X4) 0*C901 1-114-309-11 ELECT 49uF 315V RB002 1-234-376-11 RES, NETWORK 2.2K (1005X4) RB003 1-234-376-11 RES, NETWORK 2.2K (1005X4) < CONNECTOR > < SWITCH > CN001 1-779-330-51 FFC/CONNECTOR, FPC (LIF (NON-ZIF)) 12P S001 1-786-885-42 SWITCH, TACTILE (V (SELF-TIMER)) < DIODE > S002 1-786-885-42 SWITCH, TACTILE (W (ZOOM)) S003 1-786-885-42 SWITCH, TACTILE (N) 0*D001 6-501-433-01 DIODE MA2YF8000LS0 S004 1-786-885-42 SWITCH, TACTILE (B (FLASH)) * D002 6-501-861-01 DIODE CL-360S-TD4-X-TL S005 1-786-885-42 SWITCH, TACTILE (T (ZOOM)) (SELF-TIMER/AF ILLUMINATOR) D003 6-500-619-01 DIODE RB520S-40TE61 S006 1-786-885-42 SWITCH, TACTILE (v (DISP)) S007 1-786-885-42 SWITCH, TACTILE (MENU) S008 1-786-885-42 SWITCH, TACTILE (b (MACRO)) • Refer to page 5-1 for mark 0. CAUTION Danger of explosion if battery is incorrectly replaced.

DSC-W80/W85_L2 Replace only with the same or equivalent type.

5-7,

SW-494

Ref. No. Part No. Description Ref. No. Part No. Description S009 1-786-885-42 SWITCH, TACTILE (HOME) S010 1-786-885-42 SWITCH, TACTILE (z (SET)) S011 (Not supplied) ROTARY SWITCH (MODE DIAL) Electrical parts list of the SY-173 board is not shown. Pages 5-9 to 5-13 are not shown. 5-8,

Checking supplied accessories.

Note: This item is supplied with the unit as an accessory, but is not prepared as a service part. Battery Charger Battery Charger USB, A/V Cable for Power Cord BC-CSGB BC-CSGB Multi-use Terminal 0 1-555-074-91 (AUS) 0 1-479-791-12 (J) 0 1-479-791-32 1-829-866-41 0 1-782-476-71 (CH) 0 1-479-791-22 (US, CND) (EXCEPT US, CND, 0 1-823-947-71 (KR) E: Latin America, BR, J) 0 1-827-269-31 (UK, HK) BC-CSGC 0 1-827-826-41 (AEP, E) 0 1-480-175-31 0 1-828-050-31 (JE) (E: Latin America) 0 1-832-106-31 (AR) Rechargeable Battery Pack Battery Case Wrist Strap (W80) Neck Strap (W85) NP-BG1 (Note) 2-050-981-01 2-674-454-31 (Note) Conversion (2P) Adaptor Soft Carrying Case (W85) CD-ROM 0 1-569-008-12 (E: NTSC) 3-106-988-01 (Cyber-shot Application Software/ “Cyber-shot Handbook”/ “Cyber-shot Step-up Guide”) 3-094-911-01 (EXCEPT US) 3-196-435-01 (US) 3-198-533-01 (J) • Refer to page 5-1 for mark 0. 5-14,

Checking supplied accessories. Other accessories

3-095-004-01 MANUAL, INSTRUCTION (JAPANESE) (W80: J) 3-094-994-01 HANDBOOK (PDF) (JAPANESE) 3-095-004-11 MANUAL, INSTRUCTION (ENGLISH) (W80: CND, AEP, 3-094-994-11 HANDBOOK (PDF) (ENGLISH) UK, E, HK, AUS, JE/W85: CND, AEP, UK, E, AUS) 3-094-994-21 HANDBOOK (PDF) (FRENCH) 3-095-004-21 MANUAL, INSTRUCTION (FRENCH, ITALIAN) 3-094-994-31 HANDBOOK (PDF) (ITALIAN) (W80: CND, AEP/W85: CND, AEP) 3-094-994-41 HANDBOOK (PDF) (SPANISH) 3-095-004-31 MANUAL, INSTRUCTION (SPANISH, PORTUGUESE) (W80: AEP, E, AR, JE/W85: AEP, E) 3-094-994-51 HANDBOOK (PDF) (PORTUGUESE) 3-095-004-41 MANUAL, INSTRUCTION (GERMAN, DUTCH) 3-094-994-61 HANDBOOK (PDF) (GERMAN) (W80: AEP/W85: AEP) 3-094-994-71 HANDBOOK (PDF) (DUTCH) 3-094-994-81 HANDBOOK (PDF) (TRADITIONAL CHINESE) 3-095-004-51 MANUAL, INSTRUCTION (TRADITIONAL CHINESE, 3-094-994-91 HANDBOOK (PDF) (SIMPLIFIED CHINESE) SIMPLIFIED CHINESE) (W80: E, HK, CH, JE/W85: E) 3-095-004-61 MANUAL, INSTRUCTION (RUSSIAN) 3-094-995-11 HANDBOOK (PDF) (RUSSIAN) (W80: AEP/W85: AEP) 3-094-995-21 HANDBOOK (PDF) (ARABIC) 3-095-004-71 MANUAL, INSTRUCTION (ARABIC, PERSIAN) 3-094-995-31 HANDBOOK (PDF) (PERSIAN) (W80: E/W85: E) 3-094-995-41 HANDBOOK (PDF) (KOREAN) 3-095-004-81 MANUAL, INSTRUCTION (KOREAN) 3-094-995-51 HANDBOOK (PDF) (POLISH) (W80: KR, JE/W85: KR) 3-095-004-91 MANUAL, INSTRUCTION (POLISH, CZECH) 3-094-995-61 HANDBOOK (PDF) (CZECH) (W80: AEP/W85: AEP) 3-094-995-71 HANDBOOK (PDF) (HUNGARIAN) 3-094-995-81 HANDBOOK (PDF) (SLOVAK) 3-095-005-11 MANUAL, INSTRUCTION (HUNGARIAN, SLOVAK) 3-094-995-91 HANDBOOK (PDF) (SWEDISH) (W80: AEP/W85: AEP) 3-094-996-11 HANDBOOK (PDF) (FINNISH) 3-095-005-21 MANUAL, INSTRUCTION (SWEDISH, FINNISH) (W80: AEP/W85: AEP) 3-094-996-21 HANDBOOK (PDF) (NORWEGIAN) 3-095-005-31 MANUAL, INSTRUCTION (NORWEGIAN, DANISH) 3-094-996-31 HANDBOOK (PDF) (DANISH) (W80: AEP/W85: AEP) 3-094-996-41 HANDBOOK (PDF) (THAI) 3-095-005-41 MANUAL, INSTRUCTION (THAI, MALAY) 3-094-996-51 HANDBOOK (PDF) (MALAY) (W80: E/W85: E) 3-094-996-61 HANDBOOK (PDF) (TURKISH) 3-095-005-51 MANUAL, INSTRUCTION (TURKISH, GREEK) (W80: AEP/W85: AEP) 3-094-996-71 HANDBOOK (PDF) (GREEK) 3-095-005-61 MANUAL, INSTRUCTION (ENGLISH, SPANISH) (W80: US) Note: Handbooks (PDF) of each language are included in CD-ROM “ImageMixer for HDD Camcorder” (Software)/ “Handycam Handbook” (PDF). 5-15E,

HARDWARE LIST (1/4)

#1: M1.7 X 2.5 #2: M1.7 X 4.0 #3: M1.7 X 2.5 #4: M1.4 X 2.5 (Tapping) (Black) (Black) (Red) (Dark Silver) 2-635-562-11 2-635-562-31 2-660-401-01 3-348-998-81 1.7 1.7 1.7 1.4 2.5 4.0 2.5 2.5 #5: M1.7 X 3.5 (Tapping) #6: M1.4 X 1.7 #7: M1.7 X 1.6 #8: M1.7 X 3.5 (Tapping) (Black) (Silver) (Black) (Silver) 3-080-204-01 2-598-474-01 7-627-552-18 3-078-890-01 1.7 1.4 1.7 1.7 3.5 1.7 1.6 3.5 #9: M1.7 X 5.0 (Tapping) #10: M1.7 X 4.0 #11: M1.7 X 4.0 (Tapping) #12: M1.7 X 5.0 (Tapping) (Silver) (Silver) (Silver) (Black) 3-078-890-21 2-599-475-31 3-078-890-11 3-080-204-21 1.7 1.7 1.7 1.7 5.0 4.0 4.0 5.0 #13: M1.7 X 2.5 (Tapping) #14: M1.7 X 2.5 #15: M1.4 X 1.5 #16: M1.4 X 2.5 (Silver) (Silver) (Silver) (Silver) 3-085-397-01 2-599-475-11 3-062-214-01 2-586-337-01 1.7 1.7 1.4 1.4 2.5 2.5 1.5 2.5 #17: M1.7 X 1.5 #18: M1.4 X 2.5 #19: M1.2 X 4.0 (Tapping) #20: M1.4 X 3.0 (Silver) (Silver) (Red) (Silver) 2-586-389-01 2-635-591-21 3-086-156-21 2-635-591-31 1.7 2.2 1.4 1.2 1.4 1.5 2.5 4.0 3.0 3.5,

HARDWARE LIST (2/4)

#21: M1.4 X 3.0 #22: M1.7 X 5.0 (Tapping) #23: M1.7 X 4.0 (Tapping) #24: B1.7 X 5.5 (Tapping) (Black) (Silver) (Black) (Black) 2-662-396-21 3-083-261-01 3-080-204-11 4-679-805-11 1.4 1.7 1.7 1.7 3.0 5.0 4.0 5.5 #25: M1.7 X 3.0 #26: M1.4 X 2.0 #27: M1.4 X 2.0 #28: M1.4 X 4.0 (Tapping) (Black) (Silver) (Black) (Dark Silver) 2-635-562-21 2-635-591-11 2-662-396-11 3-348-998-61 1.7 1.4 1.4 1.4 3.0 2.0 2.0 4.0 #29: M1.4 X 2.5 #30: M1.2 X 4.0 (Tapping) #31: M3.0 X 4.0 #32: M2.0 X 4.5 (Tapping) (Black) (White) (Silver) (Silver) 2-662-396-01 3-086-156-11 2-102-434-01 2-102-498-01 1.4 1.2 3.0 2.0 2.5 3.5 4.0 4.5 #33: M3.0 X 6.0 #34: M3.0 X 8.0 #35: M4.0 X 6.0 (Tapping) #36: M3.0 X 6.0 (Silver) (Black) (Silver) (Silver) 3-077-331-21 3-077-331-41 3-975-291-02 4-886-821-11 3.0 3.0 4.0 3.0 6.0 8.0 6.0 6.0 #37: M2.0 X 6.0 (Tapping) #38: M3.0 X 20.0 (Tapping) #39: M2.6 X 5.0 (Tapping) #40: M2.0 X 4.0 (Tapping) (Black) (Silver) (Black) (Silver) 3-080-206-31 7-685-651-79 7-685-791-09 7-685-851-04 3.0 2.0 2.6 2.0 20.0 6.0 5.0 4.0,

HARDWARE LIST (3/4)

#41: M3.0 X 8.0 (Tapping) #42: M2.0 X 4.0 (Tapping) #43: M1.7 X 4.0 #44: M1.7 X 3.0 (Tapping) (Silver) (Silver) (Red) (Silver) 3-065-748-01 7-628-253-00 2-660-401-31 3-078-890-61 3.0 2.0 1.7 1.7 8.0 4.0 4.0 3.0 #45: M1.4 X 2.5 #46: M1.7 X 3.0 #47: M1.4 X 3.0 (Tapping) #48: M1.7 X 2.5 (Silver) (Red) (Silver) (Silver) 2-587-151-01 2-660-401-11 2-665-774-01 3-973-497-91 1.4 1.7 1.4 1.7 2.5 3.0 3.0 2.5 #49: M2.0 X 4.0 #50: M2.0 X 3.0 #51: M2.0 X 2.5 #52: M2.0 X 4.0 (Tapping) (Black) (Red) (Silver) (Black) 2-630-005-31 2-891-494-11 3-073-686-01 3-080-206-11 2.0 2.0 2.0 2.0 4.0 3.0 4.0 2.5 #53: M2.0 X 5.0 (Tapping) #54: M1.75 X 6.0 (Tapping) #55: M2.0 X 4.0 #56: M2.0 X 3.5 (Black) (Black) (Silver) (Silver) 3-080-206-21 3-318-203-11 2-655-582-11 3-067-187-11 2.0 1.75 2.0 2.0 5.0 6.0 4.0 3.5 #57: M1.7 X 4.0 #58: M2.0 X 6.0 (Tapping) #59: M2.0 X 5.0 (Tapping) #60: M2.6 X 5.0 (Black) (Silver) (Silver) (Black) 7-627-852-18 3-719-408-11 3-080-205-21 3-061-062-11 1.7 2.0 2.0 2.6 4.0 6.0 5.0 5.0,

HARDWARE LIST (4/4)

#61: M3.0 X 10.0 #62: M2.0 X 3.0 #63: M5.0 X 12.5 #64: M1.7 X 5.0 (Tapping) (Black) (Silver) (Black) (Silver) 7-682-549-09 3-080-202-21 3-060-811-21 2-666-551-21 3.0 2.0 5.0 1.7 10.0 12.53.0 5.0 #65: M1.4 X 3.5 #66: M1.4 X 1.4 #67: M1.4 X 2.0 #68: M1.7 X 4.0 (Silver) (Silver) (Silver) (Silver) 2-635-591-01 2-635-591-41 3-389-523-16 2-655-581-01 1.4 1.4 1.4 1.7 3.5 1.4 2.0 4.0 #69: M1.7 X 3.0 #70: M1.7 X 5.0 #71: M1.4 X 2.0 (Silver) (Silver) (Red) 2-599-475-21 2-599-475-41 3-208-537-01 1.7 1.7 1.4 3.0 5.0 2.0, [Description of main button functions on toolbar of the Adobe Acrobat Reader Ver5.0 (for Windows)] Toolbar Printing a text Reversing the screens displayed once 1. Click the Print button . • To reverse the previous screens (operation) one by one, click 2. Specify a printer, print range, number of copies, and other op- the . tions, and then click [OK]. • To advance the reversed screens (operation) one by one, click the . Application of printing: To set a range to be printed within a page, select the graphic Application to the Service Manual: selection tool and drag on the page to enclose a range to This function allows you to go and back between circuit dia- be printed, and then click the Print button. gram and printed circuit board diagram, and accordingly it will be convenient for the voltage check. Finding a text 1. Click the Find button . Moving with link 2. Enter a character string to be found into a text box, and click the [Find]. (Specify the find options as necessary) 1. Select either palm tool , zoom tool , text selection tool , or graphic selection tool . Application to the Service Manual: 2. Place the pointer in the position in a text where the link exists To execute “find” from current page toward the previous pages, (such as a button on cover and the table of contents page, or select the check box “Find Backward” and then click the blue characters on the removal flowchart page or drawing “Find”. page), and the pointer will change to the forefinger form . 3. Then, click the link. (You will go to the link destination.) Moving with bookmark: Click an item (text) on the bookmark pallet, and you can move to the link destination. Also, clicking can display the hidden items. (To go back to original state, click ) 3. Open the find dialog box again, and click the [Find Again] and you can find the matched character strings displayed next. (Character strings entered previously are displayed as they are in the text box.) Application to the Service Manual: The parts on the drawing pages (block diagrams, circuit dia- grams, printed circuit boards) and parts list pages in a text can be found using this find function. For example, find a Ref. No. of IC on the block diagram, and click the [Find Again] continuously, so that you can move to the Ref. No. of IC on Zooming or rotating the screen display the circuit diagram or printed circuit board diagram succes- “Zoom in/out” sively. • Click the triangle button in the zoom control box to select the Note: The find function may not be applied to the Service display magnification. Or, you may click or for zoom- Manual depending on the date of issue. ing in or out. Switching a page • To move to the first page, click the . • To move to the last page, click the . “Rotate” • To move to the previous page, click the . • Click rotate tool , and the page then rotates 90 degrees each. • To move to the next page, click the . Application to the Service Manual: The printed circuit board diagram you see now can be changed to the same direction as the set.,

Reverse 985219431.pdf Revision History

Ver. Date History Contents S.M. Rev. issued 1.0 2007.03 Official Release — —]
15

Similar documents

SPECIFICATIONS Camera [Input and Output connectors] BC-CSG/BC-CSGB/BC-CSGC
DSC-W90 SERVICE MANUAL LEVEL 2 US Model Ver. 1.0 2007.02 Canadian Model Revision History AEP Model UK Model How to use E Model Acrobat Reader Australian Model Hong Kong Model Chinese Model Internal memory Korea Model ON BOARD Argentine Model Brazilian Model Photo: Silver Link SPECIFICATIONS BLOCK DI
CAUTION If you have any questions about this product,
MVC-CD350 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Revision History Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD350 COVER SPECIFICATIONS xCamera xAC-L15A/L15B AC Adaptor [System] [Input and
Storage temperature NP-FM50 battery pack Table for difference of functions
MVC-CD200/CD300 SERVICE MANUAL US ModelCanadian Model Level 2 Ver 1.0 2001. 05 AEP Model UK Model E Model Hong Kong Model Australian Model Chinese Model Tourist Model Korea Model Photo : MVC-CD300 Japanese Model This service manual contains information for japanese model as well. On the SY-67 board
CAUTION WARNING This symbol is intended to alert You are cautioned that any changes or
MVC-CD500 SERVICE MANUAL LEVEL 1 US Model Ver 1.0 2003. 04 Canadian Model Revision History AEP Model UK Model E Model Australian Model Japanese Model Link SPECIFICATIONS SELF DIAGNOSIS FUNCTION ORNAMENTAL PARTS • INSTRUCTION MANUAL is shown at the end of this document. DIGITAL STILL CAMERA MVC-CD500
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model DIGITAL STILL CAMERA
MVC-FD81 SERVICE MANUAL US Model Canadian Model AEP Model Ver 1.0 1998.09 UK Model E Model Australian Model Hong Kong Model Tourist Model Chinese Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM CD-206 BOARD CAMERA REC 1 IC431 1,3 78µsec 9.5Vp-p 2 IC431 2,4 µ 9.5Vp-p78 sec 3 IC431 8 1.8Vp-p 78µse
S® Training Manual Digital Camera Sony Mavica Cameras MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01
S® Training Manual Digital Camera Sony Mavica Cameras Models: MVC-FD85 MVC-FD90 MVC-FD95 MVC-FD85 Troubleshooting & Circuit Descriptions Course: DSC-01 Table of Contents Introduction Floppy Disc Drive 41 Common Failures 1 Checking for Floppy Disc Drive Voltage 41 Purpose of this book 1 Checking the
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model
MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • C
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model DIGITAL STILL CAMERA
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model SPECIFICATIONS DIGITAL STILL CAMERA • Floppy disk that can be used by the MVC-FD75 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS forma
LCD screen Mass (Approx.) NP-F330 battery pack
MVC-FD87/FD92 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 06 Hong Kong Model Australian Model Korea Model Japanese Model PHoto: MVC-FD92 This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refe
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC Features • Calibration using a 32 kHz external crystal • Adjustable RC frequency with maximum +/-2% accuracy • Tune RC oscillator at any operating voltage and temperature • Tune RC oscillator to any frequency within specification
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 1981A–AVR–03/05 AVR155: Accessing an I2C LCD Display using the AVR® 2-wire Serial Interface Features • Compatible with Philips' I2C protocol • 2-wire Serial Interface Master Driver for Easy Transmit and Receive Function • Initialization and Use ofa2x1
AVR107: Interfacing AVR serial memories
AVR107: Interfacing AVR serial memories Features • Devices: AT25128A/256A, AT25F1024/2048/4096 • Full Serial Memory Functions Support • Memory Array Burst Read • Page Burst Write • Write Protection Detection • On Going Access Detection • Non-blocking Write Access • Access Status Information 1 Introd
AVR120: Characterization and Calibration of the ADC on an AVR
AVR120: Characterization and Calibration of the ADC on an AVR Features • Understanding Analog to Digital Converter (ADC) characteristics • Measuring parameters describing ADC characteristics • Temperature, frequency and supply voltage dependencies • Compensating for offset and gain error Introductio
AVR001 Conditional Assembly and portability macros
AVR001 Conditional Assembly and portability macros Features • Increased portability • Easier Code Writing • Simplified I/O Register Access • Improved Assembly Status Feedback 1 Introduction This application note describes the Conditional Assembly feature present in the AVR Assembler version 1.74 and
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2527A–AVR–9/02 AVR223: Digital Filters with AVR Features • Implementations of Simple Digital Filters • Coefficient and Data Scaling • Fast Implementation of 2nd Order FIR Filter • Compact Implementation Of 8th Order FIR Filter • Fast Implementation of 2nd
8-bit Microcontroller Application Note AVR040: EMC Design Considerations Scope
8-bit Microcontroller Application Note Rev. 1619C–AVR–01/04 AVR040: EMC Design Considerations Scope This application note covers the most common EMC problems designers encounter when using microcontrollers. It will briefly discuss the various phenomena. The refer- ence literature covers EMC design i
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 2508B–AVR–01/04 AVR182: Zero Cross Detector Features • Interrupt Driven • Modular C Source Code • Size Efficient Code • Accurate and Fast Detection • A Minimum of External Components Introduction One of the many issues with developing modern applicati
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity,
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity, allowing the smaller 20-pin AVR to be LED Drive and a • 16 Key Pushbutton Pad in4x4Matrix • 4 Digit Multiplexed LED Display with used. The circuit diagram is shown in
8-bit Microcontroller Application Note AVR180: External Brown-out Protection
8-bit Microcontroller Application Note Rev. 1051B–AVR–05/02 AVR180: External Brown-out Protection Features • Low-voltage Detector • Prevent Register and EEPROM Corruption • Two Discrete Solutions • Integrated IC Solution • Extreme Low-cost Solution • Extreme Low-power Solution • Formulas for Compone
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 1259D–AVR–04/05 AVR134: Real Time Clock (RTC) using the Asynchronous Timer Features • Real Time Clock with Very Low Power Consumption (4 µA @ 3.3V) • Very Low Cost Solution • Adjustable Prescaler to Adjust Precision • Counts Time, Date, Month, and Year wit
  Wiring Diagram
Wiring Diagram Samsung Electronics 6-1
8-bit Microcntroller Application Note
8-bit Microcntroller Application Note Rev. 2532A–AVR–01/03 AVR243: Matrix Keyboard Decoder Features • 64-key Push-button Keyboard in8x8Matrix • No External Components Required • Wakes Up from Sleep Mode on Keypress • Easily Implemented into Other Applications • Low Power Consumption • Software Conta
  Alignment and Adjustments
Alignment and Adjustments 1. Tuner FM THD Adjustment FMOutput Antenna GND SETSSG FREQ. 98 MHz Terminal Oscilloscope Adjustment FM S.S.G Input point FM DETECTOR COIL Speaker (FM DET) Terminal output Input Output 60 dB Distortion Meter Minumum Distortion (0.4% below) (Figure 1-1) Figure1-1 IF CENTER
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2540A–AVR–07/03 AVR104: Buffered Interrupt Controlled EEPROM Writes Features • Flexible Multi-byte EEPROM Buffer • Power Efficient EEPROM Access • Access Control on Buffers • EEPROM Buffer Rewrite Introduction Many applications use the built-in EEPROM of t
  Schematic Diagram - This Document can not be used without Samsung’s authorization -
Schematic Diagram - This Document can not be used without Samsung’s authorization - 7-1 MAIN 7-1 Samsung Electronics 7-2 FRONT - This Document can not be used without Samsung’s authorization - Samsung Electronics 7-2 7-3 DSP - This Document can not be used without Samsung’s authorization - 7-3 Sam
  TroubleShooting
TroubleShooting 9-1 Main 9-1 Samsung Electronics Samsung Electronics 9-2 9-3 Samsung Electronics Samsung Electronics 9-4 9-2 DVD Servo parts 9-5 Samsung Electronics Samsung Electronics 9-6 9-7 Samsung Electronics Samsung Electronics 9-8 9-9 Samsung Electronics Samsung Electronics 9-10 9-11 Samsung
AVR054: Run-time calibration of the internal RC oscillator
AVR054: Run-time calibration of the internal RC oscillator Features • Calibration of internal RC oscillator via UART • LIN 2.0 compatible synchronization/calibration to within +/-2% of target frequency • Alternate run-time synchronization/calibration to within +/-1% of target frequency • Support for
SERVICE Manual
DVD RECEIVER AMP HT-DB120 SERVICE Manual DVD RECEIVER AMP SYSTEM CONTENTS 1. Alignment and Adjustments 2. Exploded Views and Parts List 3. Electrical Parts List 4. Block Diagrams 5. PCB Diagrams 6. Wiring Diagram 7. Schematic Diagrams 8. IC block Diagrams 9.Troubleshooting - Confidential - ELECTRONI
8-bit Microcontroller Application Note AVR131: Using the AVR’s High-speed PWM
8-bit Microcontroller Application Note Rev. 2542A–AVR–09/03 AVR131: Using the AVR’s High-speed PWM Features • Analog Waveform Generation using PWM • High-speed Prescalable PWM Clock Introduction This application note is an introduction to the use of the high-speed Pulse Width Mod- ulator (PWM) avail
8-bit RISC Microcontroller Application Note AVR042: AVR® Hardware Design Considerations
8-bit RISC Microcontroller Application Note Rev. 2521B–AVR–01/04 AVR042: AVR® Hardware Design Considerations Features • Providing Robust Supply Voltage, Digital and Analog • Connecting the RESET Line • SPI Interface for In-System Programming • Using External Crystal or Ceramic Resonator Oscillators