Download: MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model

MVC-FD71 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model SPECIFICATIONS DIGITAL STILL CAMERA MICROFILM • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS format (512 bytes × 18 sector) (FD can be formatted by the MVC-FD71) SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES MARK !...
Author: Tucker Shared: 8/19/19
Downloads: 2 Views: 97

Content

MVC-FD71 SERVICE MANUAL US Model

Canadian Model AEP Model UK Model Ver 1.3 2000. 09 E Model With SUPPLEMENT-1 Australian Model (9-974-076-81) Hong Kong Model Tourist Model

SPECIFICATIONS

DIGITAL STILL CAMERA

MICROFILM

, • Floppy disk that can be used by the MVC-FD71 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS format (512 bytes × 18 sector) (FD can be formatted by the MVC-FD71) SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL PUB-LISHED BY SONY. OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer. 1. Check the area of your repair for unsoldered or poorly-sol- 4. Look for parts which, through functioning, show obvious dered connections. Check the entire board surface for solder signs of deterioration. Point them out to the customer and splashes and bridges. recommend their replace-ment. 2. Check the interboard wiring to ensure that no wires are 5. Check the B+ voltage to see it is at the values specified. "pinched" or contact high-wattage resistors. 6. Flexible Circuit Board Repairing 3. Look for unauthorized replacement parts, par-ticularly tran- • Keep the temperature of the soldering iron around 270˚C dur- sistors, that were installed during a previous repair. Point ing repairing. them out to the customer and recommend their replacement. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when solder- ing or unsoldering. – 2 –,

TABLE OF CONTENTS

SERVICE NOTE • PK-43 (MODE KEY SWITCH) Discharging of the FLASH units charging capacitor ... 4 SCHEMATIC DIAGRAM ... 4-51 LCD type judging method ... 4 • PK-43 (BACK LIGHT) How to connect the extension cable ... 5 SCHEMATIC DIAGRAM ... 4-53 Description on self diagnosis display ... 6 Power supplying method ... 6 5. ADJUSTMENTS 1. GENERAL 5-1. CAMERA SECTION ADJUSTMENT ... 5-1 1-1. PREPARATIONS BEFORE ADJUSTMENT ... 5-1 Be sure to read before using your camera ... 1-1 1-1-1. List of service tools ... 5-1 Before using your camera ... 1-1 1-1-2. Precautions ... 5-2 Parts identification ... 1-1 1. Switch settings ... 5-2 Preparation ... 1-2 2. Adjustment sequence... 5-2 Recording and playing back images ... 1-3 3. Subject ... 5-2 Changing the mode settings ... 1-5 1-1-3. Preparations ... 5-3 Using various function for recording ... 1-7 1-1-4. Discharge of flashlight power supply ... 5-4 Changing the lithium battery in the camera ... 1-7 1-1-5. Adjustment remote commander ... 5-4 Precautions ... 1-8 1. Using the adjustment remote commander ... 5-4 Trouble shooting ... 1-8 2. Precautions when using the adjustment Self diagnosis display ... 1-9 remote commander ... 5-5 1-1-6. Data processing ... 5-6 2. DISASSEMBLY 1-2. INITIALIZATION OF E AND F PAGE DATA ... 5-7 1. Intialization of E and F page data ... 5-7 2-1. CABINET (FRONT) BLOCK ASSEMBLY ... 2-1 2. Modification of F, E page data ... 5-7 2-2. FC-66 BOARD ... 2-1 3. F page table ... 5-7 2-3. LENS BLOCK ASSEMBLY ... 2-1 4. E page table ... 5-10 2-4. MOTOR UNITS ... 2-1 1-3. CAMERA SYSTEM ADJUSTMENT... 5-12 2-5. FDD BLOCK ASSEMBLY ... 2-2 1. Adjustment points when major parts 2-6. PK-43 BOARD, LIQUID CRYSTAL have been replaced... 5-12 INDICATOR MODULE ... 2-2 2. Power supply voltage check ... 5-12 2-7. CIRCUIT BOARDS LOCATION ... 2-2 3. HALL adjustment ... 5-12 4. Flange back adjustment ... 5-13 3. BLOCK DIAGRAMS 5. Flange back check ... 5-14 6. Picture frame setting ... 5-14 3-1. OVER ALL BLOCK DIAGRAM ... 3-1 7. Light level adjustment ... 5-15 3-2. CAMERA BLOCK DIAGRAM ... 3-5 8. Auto white balance reference data input ... 5-15 3-3. FDD INTERFACE BLOCK DIAGRAM ... 3-7 9. Auto white balance adjustment ... 5-16 3-4. MODE CONTROL BLOCK DIAGRAM ... 3-11 10. White balance check ... 5-16 3-5. LCD BLOCK DIAGRAM ... 3-13 11. Hue gain adjustment ... 5-17 3-6. POWER BLOCK DIAGRAM ... 3-16 1-4. LCD SYSTEM ADJUSTMENT ... 5-18 4. PRINTED WIRING BOARDS AND 1. Power supply voltage check ... 5-19 2. EVR initial data input ... 5-19 SCHEMATIC DIAGRAMS 3. VCO adjustment ... 5-19 4. D RANGE adjustment ... 5-20 4-1. FRAME SCHEMATIC DIAGRAM ... 4-1 5. BRIGHT adjustment ... 5-20 4-2. PRINTED WIRING BOARDS AND 6. CONTRAST adjustment ... 5-21 SCHEMATIC DIAGRAMS ... 4-4 7. V-COM level adjustment ... 5-21 • CD-196 (CCD IMAGER) 8. V-COM adjustment ... 5-22 PRINTED WIRING BOARD AND 9. White balance adjustment ... 5-22 SCHEMATIC DIAGRAM ... 4-5 • RL-50 (RELEASE SWITCH)/FC-66 (MAIN) 1-5. SYSTEM CONTROL SYSTEM ADJUSTMENT ... 5-23 PRINTED WIRING BOARDS ... 4-7 1. Battery down adjustment ... 5-23 • FC-66 (CAMERA) 2. Battery down check ... 5-23 SCHEMATIC DIAGRAM ... 4-13 • FC-66 (DRAM CONTROL) 6. REPAIR PARTS LIST SCHEMATIC DIAGRAM ... 4-15 6-1. EXPLODED VIEWS ... 6-1 • FC-66 (D/A CONVERTER) 6-1-1. CABINET (FRONT) SECTION ... 6-1 SCHEMATIC DIAGRAM ... 4-18 6-1-2. CABINET (REAR) SECTION ... 6-2 • FC-66 (CAMERA SERVO) 6-1-3. LENS BLOCK ASSY SECTION ... 6-3 SCHEMATIC DIAGRAM ... 4-21 6-2. ELECTRICAL PARTS LIST ... 6-4 • FC-66 (FDD CONTROL) SCHEMATIC DIAGRAM ... 4-26 *The color reproduction frame is shown after the • FC-66 (MODE CONTROL), (EVR DECODER) page of ELECTRICAL PARTS LIST. SCHEMATIC DIAGRAM ... 4-29 • FC-66 (DC/DC CONVERTER) RL-50 (RELEASE SWITCH) SCHEMATIC DIAGRAM ... 4-34 • PK-43 (LCD PANEL, MODE KEY) PRINTED WIRING BOARD ... 4-37 • PK-43 (FDD INTERFACE) SCHEMATIC DIAGRAM ... 4-42 • PK-43 (RGB CECODER) SCHEMATIC DIAGRAM ... 4-45 • PK-43 (LCD TIMING GENERATOR) SCHEMATIC DIAGRAM ... 4-49 – 3 –,

SERVICE NOTE

[Discharging of the FLASH unit’s charging capacitor] Discharging the Capacitor Short-circuit between the positive and the negative terminals of The charging capacitor of the FLASH unit is charged up to the charged capacitor with the short jig about 10 seconds. maximum 300 V potential. There is a danger of electric shock by this high voltage when the battery is handled by hand. The electric shock is caused by the Flash unit charged voltage which is kept without discharging when the main power of the MVC-FD71 is simply turned off. Therefore, the re- maining voltage must be discharged as described below. Charge Preparing the Short Jig capacitor To preparing the short jig. a small clip is attached to each end of a resistor of 1kΩ /1W (1-215-869-11) Wrap insulating tape fully around the leads of the resistor to pre- vent electrical shock. – + 1kΩ/1W Wrap insulating tape. Short jig [LCD type judging method] The LCD type can be judged by measuring resistance between 4 pin and !¢ pin of CPC-9 jig. Resistance LCD Type 10 kΩ SHARP0ΩCASIO Digital voltmeter CPC-9 jig (J-6082-393-B) !¢ pin 4 pin – 4 –, [How to connect the extension cable] 4) Open the lithium lid. (See Fig. 3.) 5) Mount the flexible board on CN013. (See Fig. 3.) 1) Remove the PK-43 board and the liquid crystal indication module. (See page 2-2E.) Note : Be careful not to breake the flexible board of the floppy disk drive. 2) Install the Extension cable (J-6082-427-A) on the rear cabi- net. (See Fig. 1.) Contact side CN013 Contact side Four screws Extension cable Lithium lid (J-6082-427-A) Fig. 3 6) Install the PK-43 board. (See Fig. 4.) Extension cable (J-6082-427-A) Contact side PK-43 board Fig. 1 3) Install the floppy disk drive. (See Fig. 2.) Contact side CN601 Extension cable (J-6082-427-A) CN602 For both two cables, the contact points are Extension cable on this side. (J-6082-427-A) Fig. 4 Floppy disk drive Flexible board Note : The floppy disk drive and PK-43 board could be destroyed unless (CN012) the flexible board is connected normally to the connector. Flexible board (See Fig. 5.) (CN011) Fig. 2 Good NG Fig. 5 – 5 –, [Description on Self-diagnosis Display] Note : The “Self-diagnosis” data is backed up by the coin lithiumbattery. The data will be lost and initialized when the coin lithium battery is removed. Display Code Countermeasure Cause Caution Display During Error Change the disk and turn off the main C:32:01 Defective floppy disk. DRIVE ERROR power then back on. • The type of floppy disk that cannot be Replace the floppy disk. used by this machine, is inserted. C:13:01 Format the floppy disk with the MVC- (Such as 2DD) DISK ERROR FD71. • Data is damaged. • Unformatted disk is inserted. Flash LED Checking of flash unit or replacement of Abnormality when flash is being E:91:01 Flash display flash unit charged. Flashing at 3.2 Hz E:61:00 Checking of lens drive circuit When failed in the focus initialization. — E61:10 [Power supplying Method] Use the AC power adaptor (BC-V615) when supplying the power to this set. – 6 –,

MVC-FD71 SECTION 1 This section is extracted from GENERAL instruction manual.

1-1, 11-9-9E,

SECTION 2 DISASSEMBLY

Note: Follow the disassembly procedure in the numerical order given. 2-1. CABINET (FRONT) BLOCK ASSEMBLY 2-2. FC-66 BOARD 3 Connector (CN907) 3 Connector 3 Connector (CN910) (CN901) 1 Two screws (M2) 1 Two screws 3 FC-66 board (M2) 1 Two screws (M2) 2 Three screws (M2 × 3) 1 Frexible board 1 FP-34 frexible board (CN401) (CN101) 1 screw 2 Cabinet (front) (M2) 1 FP-35 frexible board block assembly (CN601) 2-3. LENS BLOCK ASSEMBLY 2-4. MOTOR UNITS 6 Focus motor unit 4 Zoom motor unit 1 FP-34 flexible board (CN101) 5 Two screws 2 Boss 1 Break solders of mortor units. 3 Screw 1 Flexible board (CN401) 3 Flexible board 3 Lens block assembly 2 Screw Note: Flexible board of zoom lens is not supplied. Please be careful not to break the flexible board when you change the motor unit. 2-1, 2-5. FDD BLOCK ASSENMBLY 2-6. PK-43 BOARD, LIQUID CRYSTAL INDICATOR MODULE 1 Open the side 7 Liquid crystal indicator module Cabinet. 6 PK-43 board Zoom knob 5 screw RV701 3 Cold cathode fluorescent tube 2 Two screws S710 3 Flexible board (CN601) 2 FDD block assembly BRIGHT knob PLAY/CAMERA knob 3 Flexible board (CN602) S708 1 Flexible board 4 Flexible board (CN851) 5 Two screws (CN901) 2 Two screws 5 Four screws Note: When installing PK-43 board, connect RV701 with zoom knob, S708 with PLAY/CAMERA knob and S710 with BRIGHT knob. 2-7. CIRCUIT BOARDS LOCATION FC-66 ( CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO,RL-50 FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER,(RELEASE SWITCH) DC/DC CONVERTER ) CD-196 (CCD IMAGER) FLASH UNIT PK-43 ( FDD INTERFACE, RGB DECODER, LCD TIMING GENERATOR, MODE KEY SWITCH, BACK LIGHT ) 2-2E, FC RESET SENS ZM RESET SENS XRLS ON1,2 XRST PDR CAM SI,CAM SO,XCAM SOK,XCS DIC HALL AD CAM SO,XCAMSCK,XRSTSYS TG_CS

RESET

XCAMSCK,CAMSO,CAMSI BACK UP XCS_CAM_D/A G CAM STBY XCSIDIC,XCAMSCK,CAMSO,CAMSI XRST CORE XCSIDIC,XRSTSYS DR_BUS_RQ XHISCK,HISO,XCSIDIC2 ADDRESS BUS DATA BUS A10-17 XHISCK,HISO,HISI RES,CE CONTROL SIGNAL XHI SCK,HISO

MVC-FD71 SECTION 3 BLOCK DIAGRAMS

3-1. OVERALL BLOCK DIAGRAM

CD-196 BOARD FC-66 BOARD

(SEE PAGE4-6) (SEE PAGE 4-13~4-36) PK-43 BOARD (SEE PAGE 4-42~4-54) IC104 IC503 IC601 IC802 LCD901 PANEL R VR IC401 IC102 CAY0-7 PANEL Y0-7 CCD PANEL G RGB VG ZOOM IRIS AD1-10CCD DECODER LENS MOTOR IMAGER V1,V3,V2A,V2B, IC103 SHP,SHD, XCLPOB PANEL B VB COLOR H1,H2,RG CLPDM,CLD S/H AGC CAC0-7 PANEL C0-7 LCD A/D G CAM STBY D/A IC903 IC901 MONITOR PBLK Y/CAGC PROCESSOR CA_VD,CA_HD,CAC_VD SYSH,SYSV COMVERTER PANEL XHD M902 M901 CONT1,2 LCD ZOOM MOTOR FOCUS MOTOR MCK DRC PANEL XVD(SYS V) TIMING FOCUS TGZOOM GENERATOR SENSOR SENSORMM

HALL

SENSOR BL UNREGMCK CN802 T851 FR,HR IC804

SW

IC801 CPC IC251 D0-15 D0-7 BUS D0-7 ND801 BACK LIGHT

BUFFER

IC401 IC404 IC301 XHI SCK,HISO EVR DC/DC IC252 IRIS IRIS CONT1,2 XCS LCD D/A DECODER CONVERTERA0-3 BIAS DRIVER EVR DATA HALL OFFSET,GAIN HALL AD HALL DECODER XWE,XOE PANELIC801 AMP 4.9VIC601 A1,A2 IC402 IC403 IC501 FDD WRITE DATA B1,B2 FOCUS MOTOR DIR0A,0B CAC_VD DRIVE D0-D15

CONTROL

READ DATA A3,A4,B3,B4 ZOOM MOTOR DIR1A,1B DRIVE RAM SIDE1 SELECT,STEP,DIRECTION,WRITE PROTECTFOCUS CONTROL A0-9 ZM RESET SENS DECODER TKACK00,INDEX FC RESET SENS SHOCK SENS, WRITE GATE IC807 DATA LATCH D0-15 IC802 IC803 FDD FDD DRIVE RAM IC805IC705 OSD INTERFACE UNITA0-9 PYRA R/G/B/BLK XWE,XOE D0-15 DISK CHANGE,X2DD IC806 A0-9 FD READY,MOTOR ON,DRIVE SELECT XCASH,XCASL,XRAS,XOE,XWE SYSTEM,CONTROL X_BUS_RQ DISK IN DR_BUS_RQ IC703 HI SI,HI SO,XHI SCK EEPROM TEMP LENS TEMP AD

SENSOR

S206 S703 S706 S710 CR,RESET PICTURE SUB BRIGHT LCD EFFECT ( + ) BACK LIGHT D706 IC702 XCS MC,XMC CANCEL,XMC NMI SELF HI PROCESSOR S705 S709 TIMER XCS OSD KEY AD0~2 CONTROL SUB BRIGHT SW FLASH ( - ) XCS LCD-D/A S704 S707 DISK IN DISPLAY PROGRAMAE S702 XPWR SW

POWER

S708 XCAM/PB SW PLAY/

CAMERA

RV701 ZOOM AD

ZOOM

D701 IC701 XACS LED

ACCESS

INITIAL RESET BACK UP VCC D702 XCHG LED FLASH

CHARGE

SHUTTER BEEP BZ701 SO51 (BEEP) BH701 LI 3V LITHIUM

RL-50 BOARD BATTERY

(SEE PAGE4-34) 3-1 3-2 3-3, – + + – AGC CONT2 AGC CONTZ1

STBY

+ – – + – +

MVC-FD71 MVC-FD71

3-2. CAMERA BLOCK DIAGRAM 2 -10

CD-196 BOARD RECFC-66 BOARD

(SEE PAGE 4-6) !§ REC(SEE PAGE 4-13,21,32) 7 REC 1.5Vp-p IC401 IC102 0.025µsec 3.2Vp-p IC104 2.3Vp-p S/H,AGC,A/D Y/C PROCESSOR H CCD IMAGER Q401 0.025µsecCN401 CN101 CCD OUT D0 2 88 AD0 CAMY0 38CCD OUT 7 BUFFER 2 15 26 DIN CAY0-7 IC503 83-87,89-91 1 REC D9 11 97 AD9 CAMYZ 45 2 7.6Vp-p Q101-104 CAM 15V89CAM 15V 8 CAM 15V CLPOB 20 83 XCLPOB CAMC0 29 TO -5.5V SWITCH IC103 CAC0-7 IC503 92-9936 FDD INTERFACE BLOCK-5.5V 5 12 5 CAM-5.5V TG CAMC7 (SEE PAGE 3-7) H V1 1 V17 MFRO 57 CA VD IC503 80 V326V3 10 40 V1 SHP 17 21 XSHP REC V2A 11 41 V3 SHD 18 22 XSHD MHRO 58 CA HD IC503 81 4 V2A3512 42 V2A CLPDM 15 23 CLPDM CFRO 65 CAC VD IC5037.6Vp-p 82 V2B44V2B 13 44 V2B CLD 35 16 ADCLK MCK IC503 78 PBLK 21 19 PBLK VREF PYRA IC601 H1 13 17 H1 13 15 H2 2 12 H1 XCE 11 CS IDIC IC702 24 H2 14 16 1 13 H2 SCK 12 CAM SCK IC702 35 RG 12 14 RG39RG SI 13 CAM SO IC702 34H 29 30 18 SO 14 CAM SI IC702 33 47 REC XCLK 10 XRST CORE IC702 91 X101 47 OSCO FRI 34 81 FRO WWE 84 SL SHUTTER WE IC702 68 HRI 33 82 HRO36MHZ 48 OSCI MCK 38 85 MCK 2.3Vp-p !£ REC 28.63MHz !™ REC !¢ WEN3GCAM STBY IC702 95 SSK 28 6Vp-p 6Vp-p SSI 27 0.025µsec 0.025µsec RST 25 RST SYS IC702 9 SEN 29 TG CS IC702 92 CAM DD ON IC702 37 IC301 EVR DATA DECODER 7 AGC CONT1 CLK 19 TO 8 AGC CONT2 SI 20 POWER BLOCK FLASH ADJ 11 FLASH ADJ SO 21F CHG (SEE PAGE 3-16) 6 F CHG XCS 22 CS CAM D/A IC702 2512 10 4 IRIS CONT1 VREF PYPA 12 13 5 IRIS CONT2 IC404 (1/4) LENS UNIT IRIS CONT HALL HALL TO IC401 (2/2) OFFSET GAIN MODE CONTROL BLOCK IRIS IC401 (1/2) HALL AMP12(SEE PAGE 3-11) MOTOR DRIVE( + ) CN401 Q402 HALL AMP 6

M 1 D3.2V

2 7 DRIVE( - ) 1 5 D3.2V6 INVERTER 3 IC405 VREF BUFFER IC404 4 1(2/4) HALL AMP 5 IC404 BIAS( + ) 7 (3/4) 2 6 HALL AMP 10 + 8 HALL HALL( - ) 9 – HALL AD IC702 80 SENSOR 3 HALL( + ) IC404 (4/4) 5 Q403 HALL GAIN CONT3 BIAS( - ) 1 4 INVERTER 2 ZOOM ZOOM RST 17 ZM RST SENS IC702 SENSOR 67 FOCUS FOCUS RST 19 FC RST SENS IC702 66

SENSOR

IC402 IC403 FOCUS/ZOOM MOTOR DRIVE FOCUS/ZOOM CONTROL DECODER M902 Z_A ZOOM MOTOR Z_B78A3 EN4 19 17 EN1 SENS 0 19 Z_XA 8 10 A4 EN3 17 SENS 1 18M Z_XB 9 22 B3 IN4 18 16 DIR 1B 10 20 B4 IN3 16 15 DIR 1A VD IN 1 SCK 4 M901 SI 5FC_A FOCUS MOTOR FC_B 11 5 A1 EN2 15 14 END SO 6 FC_XA 12 7 A2 EN1 13 CS 3M 13 FC_XB 26 B1 IN2 14 13 DIR 0B 14 24 B2 IN1 12 12 DIR 0A CLR 9 RST PDR IC702 94 TEMP TEMP COMP 15 SENSOR Q401 LENS TEMP AD IC702 79 SENS VCC 20 ZOOM SENS SWITCH LENS RST LED IC702 3 3-5 3-6,

MVC-FD71

3-3. FDD INTERFACE BLOCK DIAGRAM $§ REC/PB @£ REC/PB !ª REC/PB !¢ REC/PB

FC-66 BOARD 3.2Vp-p $∞ REC/PB #¶-$¢ REC/PB

(SEE PAGE 15,18,26,29) 83 3.2Vp-p IC601 V 0.025µsec 3.2Vp-p 87 Y0 H D/A CONV. 1Vp-p 0.8Vp-p 1Vp-p 7 . H H HIC104 38 45 CAY0 8 89 Y7 58 Q601 CN602 91 Y0 6.2 37 Y0 23 PANEL R8 8 IOR 64 BUFFER Y7 44 Y7 92 C0 66 29 36 Q602IC104 CAC07899 C7 5 C0 PANELG4IOG 19 BUFFER 16 TO 2 C3 LCD BLOCK C0 72 Q603 PK-43 BOARD 4 CN603 IC103 38 PANEL B MCK 78 C3 75 IOB 14 BUFFER 21 (SEE PAGE 3-13) IC104 85 TO PANEL HD31 MCK HDO 47 11CAMERA PANEL VD BLOCK 34 VCK 13 (SEE PAGE 3-6) IC503 45 HD DVDD1 6 D3.2VIC104 57 CA VD 80 VD L601 $¶ REC/PB DRC 46 VD AVDD1 18

IC705 AVDD2 22

IC104 58 CA HD 81 HD OSD VREF R 21 3.1Vp-p

RSTSYS

IC104 65 4 RSTSYS VREF G 17 H TO CACVD 82 XVOC 56 20 HSYNC VREF B 13 VREF PYRA IC301 12 CAMERAIC403 1 SYS H BLOCK SYS V 57 19 VSYNC (SEE PAGE 3-6)

TO

POWER BLOCK STRBON 53 STRBON 17 48 RST SYS CGR RST 27 (SEE PAGE 3-17) HI SCKXSCK 43 CS IDIC241 DR BUS RQ 16 36 CGG CS 26 HI SCK 18 32 CGB SCK 29 RST SYS MCK 78 8 MCK HI SO 40 RST SYS 15 1 CGBLK SI 28

HISO

45 SI CSIDIC2 1 SCLK RAS XCS 44 34 RAS3SIN CASL 36 CASL BUS RQ 42 HI SCK 2 CS SYS V IC702 62 CASH 35 CASH WE 37 WE RST SYS IC702 9 OE TO39 OE CS IDIC2 IC702 28 MODE CONTROL HI SO AD0 9 D0 15 HI SCK IC702 46 BLOCK .IC801 (SEE PAGE 3-11)35712 100 15 20 22 25 . 27 29. 31 33 HI SO IC702 45 FDD CONTROL 43 10 D4.9V CS OSD IC702IC804 CS OSD 16 BUS BUFFER 57 VDD1 42

IC807 6.0 D0 VDD1 43 FLASH MEMORY D0 B0 6.2 L801

D7 B7 63. D7 VDD2 16 A01,02 65. 67 PK-43 BOARD $™ REC/PB 7 29 IC806 (SEE PAGE 4-42) A0 D0 IC501 SYSTEM CONTROL XA1 828. 3.610 A01 X803 18 16 50 CSA9 D15 38 DRAM(16M) 16.4 A02 16MHz 162 RSEL XA2 83 *£ REC/PB 4MHz 5Vp-p 25 45 2 21 62 BREQ 15.8 XB1 86 IC601 24 A0 DQ0 . 15.5 24 10 . 7 16 AD0 152 FDD INTERFACE 27 A9 DQ7 10 30 MCD00 16 16MHz 3.2Vp-p . CN602 CN603 CN6021.0 AD15 14.8 SIDE 1 SEL32 41 32

ERASE

MCD15 14.6 SIDE 36 5651SSI E01 75 9 144 TRACK 00 R/W A34 TRK0 24 50 1144 3 T00 RW1B 68 . STEP142 43 18 6 R/W BRAS 46 STEP 10 6 ISTP RW1A 6918 RAS DIRECTION R/W B CASL 49 A0(HBS) 69 51 A0 DIR 8 44 17 7 IDIR RW0B 71 535 CASL INDEX R/W A CASH PB3 12 70 TC INDEX 76 37 24 9 IDXO RW0A 72 434 CASH READ DATA ERASE WE PC3 11 71 INT RDATA 27 55 6 13 RDO E00 76 2 17 WE WRITE DATA OE PB6 13 69 DMAAK WDATA 11 47 14 5 IWD OSCO 4233 OE WRITE PROTECT PB4 23 45 RESET WPRO 26 5472WPO X601 FLOPPY DISK CS2 57 48 ENRW 4MHzIC802 DRIVE UNIT OE RO 53 46 RD CN601 119 IRQ1 1 OSCI 43WE TO WR 59 47 WR WE 13 4 WRITE GATE

CLOCK

IC702 99 DR BUS RQ 10 IRQ6 51 10 4 IWG CPO 47 132 MODE CONTROL 17 FPTSFPTS 51 BLOCK IC702 96 MC CANCEL 118 IRQ7 EN 100 16 HOS (SEE PAGE 3-11) IC702 44 30 READY EM2 HDS 50 HISI 2 PB9 MCMC 12 IC7034448 INDEX 116 INDEX50 NMI 47 IC702 MC NMI DISK CHANGE PA IC702 18 DISK IN PC0 24 40 21 11 DCO PA0 26 6 FD READY PNA 39 22 10 RDYO PA1 28 7 RST SYS MOTOR ON PB 117 RES PC2 29 41 208MON PB0 35 5 DRIVE SELECT PNB PB1 28 38 23 12 DSEL PB1 33 8 HI SCK X2DD STBY 1 SCK0 PB0 26 42 19 18 DIIV STBY 22 3 HI SO TOS1 3 RXD0 TOSI 21 1 RAS RAS

DISK

58 IC803 IC805 D4.9V DISK IN 52 18 48 DISK INCASL 108 SHOCK XTAL CASL 61 SHOCK SENSOR CASH SIG DET.X802 CASH 623615MHz 107 EXTAL 1 S1 PS VCC Q801Q5SE801 OUT41CK PC5 27 2 VR2 10 7 PB A0 B1 B0 RDQ39876DISK IN 15MHz 3.2Vp-p 21 3-7 3-8 3-9,

MVC-FD71 MVC-FD71

3-4. MODE CONTROL BLOCK DIAGRAM

FC-63 BOARD PK-43 BOARD

(SEE PAGE 4-20,29) IC702 (SEE PAGE 4-51) HI CONTROL CN601 CN603 IC102 18 G CAM STBY 95 G CAM STBY LANC OUT 2 LANC OUT 60 2 LANC OUT Q101-104 CAM DD ON 37 CAM DD ON LANC IN 1 LANC IN 59 1 LANC IN IC104 84 IC103 3 SL SHUTTER WE 68 SL SHUTTER WE CS LCD D/A 26 CS LCD D/A 13 47 CS LCD D/A TO LCD S704

BLOCK

CN401 15 LENS TEMP AD 79 LENS TEMP AD 51 HI SCK BACK LIGHT KEY AD0 82 KEY AD0 (SEE PAGE 3-13) 25 49 HI SO KEY AD1 83 KEY AD1 ON OFF KEY AD2 84 KEY AD2 29 DISK IN 18 DISK IN 47 IC301 22 CS CAM D/A 25 CS CAM D/A PWR SW 14 PWR SW 17 IC404 8 HALL AD 80 HALL AD CAM/PB SW 15 CAM/PB SW 19 S701 CONTROL SW Q401 LENS RST LED 3 LENS RST LED ZOOM SW 78 ZOOM SW 23 Q703 SET IC403 18 CN401 17 ZM RST SENS 67 ZM RST SENS 35 KEY AD0 UP S703 S706 TO CAMERA IC403 19 CN401 19 FC RST SENS 66 FC RST SENS REC LED 55 LED ACS LED 28 KEY AD1 LEFT RIGHT PICTURE BRIGHTDRIVE BLOCK IC403 9 RST PDR 94 RST PDR 33 EFFECT (+) (SEE PAGE 3-6) Q704 DOWN IC103 25 RST SYS 9 RST SYS STB LED 56 LED CHG LED 26

DRIVE

IC104 11 IC403 3 CS IDIC 24 CS IDIC Q707 IC103 28 IC104 12 IC403 4 IC301 19 CAM SCK 35 CAM SCK MELODY ENV 59 BUFFER BEEP 31 31 KEY AD2 IC103 27 IC104 13 IC403 5 IC301 20 CAM SO 34 CAM SO Q708 LI 3V 30 IC104 14 IC403 6 IC301 21 CAM SI 33 CAM SI MELODY 36 S702SW HI SCKUNREG2 9HI SO 11 43 PWR SW POWERON D703 BATT SENS 71 S705 S709 S708 FLASH BRIGHT IC104 10 RST CORE 91 XRST CORE IC701 41 CAM/PB SW (-)PLAY/ IC103 29 TG CS 92 TG CS 42 INITIAL RESET CAMERA 51 BACK UP VCC BACKUP VCC 6 VOUT IC806 10 119 IC503 41 DR BUS RQ 99 DR BUS RQ 77 86 VIN 7 D701 D3.2V VBAT 3 37 ZOOM SW AD RV701CN602 48 DISK IN 18 DISK IN 87 ZOOM SW IC806 118 MC CANCEL 96 MC CANCEL VRO 8 IC806 116 MC NMI 50 MC NMI BATT IN 61 4 CS A4.9V LIPRE END 69 2 PRE END ACS LED D701TO FD CONT IC503 57 SYS V 62 SYS V RESET 38 5 REST 34 ACCESS LED S704 S707 BLOCK DISPLAY PROGRAM (SEE PAGE 3-7) CHG LED D702 IC503 40 IC806 117 IC601 27 RST SYS DRY BATT 72 36 AEFLASH LED IC705 2 CS OSD 43 CS OSD Q701 LI 3V IC503 44 IC601 26 CS IDIC2 28 CS IDIC2 Q702 32 BH701 IC705 1 IC503 43 IC806 1 IC601 29 HI SCK 46 HI SCK BATT SI 48 IF LITHIUM IC806 3 IC503 45 IC705 3 IC601 28 HI SO 45 HI SO BATT SO 49 BLOCK BATTERY Q701, 702 29 BEEP BZ701IC806 2 HI SI 44 HI SI $º REC/PB AMP (BUZZER)

IC703 EEPROM

20MHz OUT 40 D3.2V 20MHz 0.6Vp-p DO 4 X70120MHz %£ REC/PB 8 VCC DI 3 20MHz IN 41 SCK 2 CS 1 23 CS EEPROM RST 6 12 EEPROM WE 32.7kHz 3.0Vp-p 32kHz IN 52 CN910 7 KEY AD3 85 KEY AD3 X702 D706 RL-50 BOARD32.768MHz CN910 8 FOCUS B 73 FOCUS B 32kHz OUT 53 SELF TIMER (SEE PAGE 4-45)Q706 CN910 9 CN401 1 FOCUS A 70 FOCUS A TO POWER SELFTMR LED 58 LED S501 CN501 (SHUTTER) BLOCK DRIVECAM DD ON 37 CAM DD ON CN907 (SEE PAGE 3-16) 5LCD DD ON 47 LCD DD ON SHTR SW 16 2 SYS DD ON 29 SYS DD ON SHTR LOCK SW 17 STB CHG 93 STB CHG DC PACK SW 65 3 STB FUL 32 STB FUL CN901 2 BATT SIG 3 BATTERY 4 BATT/EXT

TERMINAL

3-11 3-12, BRT TST W MSKV RGB AMP

CONTRAST

SUB CONT R SUB CONT B SUB BRT R FRPT FRP SUB BRT B FRPV BRIGHT COM AMP COM ADJ COM-O – + + –

MVC-FD71

3-5. LCD BLOCK DIAGRAM

PK-43 BOARD

(SEE PAGE 4-44, 45, 49, 53) 8 REC/PB 9 REC/PB20REC/PB22REC/PB 1 REC/PB 4Vp-p 4.2Vp-p 5.5Vp-p 0.6Vp-p 2.1µsec0.5Vp-pHHHHIC80124REC/PB EVR 4.3Vp-p Q856 BL LEVEL 12 SWITCHING XEXI IN 15 4 L252 L253 21 SO JIG CON 16 BL UNREG 2 T851 TO MODE CS LCD D/A 22 XEN BRIGHT15INV TRANS CN851 CONTROLH16HIGH BLOCK HI SCK 19 CLK 191 3 (SEE PAGE 3-12) HI SO 20 SI BRTR4IC851 182 BRTB5DC/DC CONV. Q857, 859 CONTRAST 6 BL RGB AMP 9 IC802 Q854 LEVEL Q860 ND801 AMP 1 DRIVE D 3.2V 14 VCC COM ADJ 10 LCD DRIVER INV 4 BACK LIGHT 38 30 40 43 42 32 31 39 35 PANEL 3.2V 13 VDD VCO 7 SW Q851, 852 23 VDDA V COM 8 PANEL 4.9V 2 VCC IC852 5 103 2 BRT TST 18 VSH 20 PANEL 4.9V SAW 4 LOW7 CONV. 3 COM TST 17 OSC Q255 D853 CN603 R OUT ERROR20 SHROT PANEL G 42 AMP8 G OUT CIRCUIT 522 PROT. Q853 D852 PANEL R 44 9 LCD DRIVER B OUT 24 PROTECT TO SWCOM OUT FDD INTERFACE BLOCK PANEL B 40 10 41 FC-66 BOARD CN602 PANEL VD 48 (SEE PAGE 3-9) VCC1 VCC2 CN901 48 28 29 44 2593PANEL HD 50 10 5 PANEL 6.5V 11 4 PANEL 3.2V VB 6 SHARP CASIO GENERATOR IC902 PANEL 4.9V PANEL 6.5V 13 2 Q903 – 906 V COM + 5 COM 7 14 15AMP BUFFER PANEL COM VGL 15 REC/PB GENERATOR10

IC901 PANEL -15.3V 16 22

LCD VCC TIMING GENERATOR 22GENERATOR 0.5Vp-p HDB 4 PANEL 13.2V 24 24 H LCD901 27 OSCI COLOR LCD VCO DOWNO 13 21 16VCO MONITOR GRES 14 20 20 26 OSCO FRP 11 FRPV COMTST 47 COMTST FRPT 37 REC/PB HCNT 12 SRT 2 20 5 13 IC903 GPCK 15 19 19

SWITCH

3.2Vp-p MCLK 24184IN/OUT2 OUT/IN23HSW9WMSKV CN802 1 IN/OUT1 OUT/IN4 10 34 REC/PB CLR 23 2 10 5 JIG HD 8 IN/OUT3 OUT/IN1 2 37 CSY/XHD RIGHTO 18776JIG VD 11 IN/OUT4 OUT/IN3 9 XVD 3.2Vp-p GSRT 16 1818B341VRESET 17 17 17 CPC3ROE 22 3 112GTE3 SRT 1 21 4 12 9 VG 30 7 HSY SHARP CASIO 12 LANC OUT PHOOUT 2 LPF 1 PHOIN PD 32 LANC OUT TO MODE 11 LANC IN LANC IN CONTROL BLOCK PANEL 4.9V (SEE PAGE 3-12) 3-13 3-14 3-15, CAM DD ON

MVC-FD71

3-6. POWER BLOCK DIAGRAM CN401 ZOOM IRIS D 3.2V SENSOR MOTOR 1 LENS UNIT Q401

FOCUS

20 SENCE VCC1FCHG F CHG IC301

SENSOR

ADJ LEVEL TO CAMERA BLOCK (SEE PAGE 3-5)2 FLASH ADJ IC301 11 4 STRB ON STRB ON IC503 53 TO FDD INTERFACE BLOCK (SEE PAGE 3-7) STB FULL CD-196 BOARD5 STB FULL IC702 32 MF (SEE PAGE 4-6) BLOCK FLASH 7 KEY AD3 KEY AD3 IC702 85 IC401 CN401 IC103 FOCUS B TO MODE CONTROL BLOCKUNIT 8 FOCUS B IC702 7398(SEE PAGE 3-11) 9 FOCUS A FOCUS A IC702 70 CCD IMAGER 12 5 TG 12 STB CHANGE STB CHG IC702 93 IC102 1 BATT LINREG F901 UNREG 1 (FLASH) S/H AGC F902 UNREG 2 (P5V/CAM15V) UNREG A/D CONT. BATTERY F903 UNREG 3 (BL UNREG) BL UNREG TERMINAL F904 UNREG 4 (D3.2V/4.9V) L101 2 BATT GND IC104 IC403 L102 L404 ZOOM/FOCUS PK-43 BOARD CN901 Y/C PROCESSOR CONTROL DEC. (SEE PAGE 4-42, 45, 49, 51, 53) L901 L902 CN601 IC901 FC-66 BOARD IC402 L401 CAM P 5V ZOOM/FOCUS SWITCHING (SEE PAGE 4-13, 15, 18, 21, 26, 29, 34) 4LENS DRIVE REG CONTROL IC601 L601 IC401 FLOPPY VCC 18 L403 FDD VCC OUT 45 IRIS MOTOR DISK DRIVE IC404 INTERFACE DRAVE HALL AMP CN602 P 5V HALL AMP IRIS DRIV FBA 5 BA10324AFV 8 Q906 SWITCHING L905 IC405 D701 D702 P5V REF DET ACCESS FLASHCN602 CN603 CHARGE Q911 OUT A 46 Q101-104 FDD P 5V 33 27 SCPA8EMERGENCY CAM 15V 34 28 DET IC903IC301 L301 Q918, 922, 928, 929 SWITCH FB B 10 15V CAM -7.5V EVRREGULATOR DATA DEC. T901 IC902L901 SCP B 13 Q907 DC/DC SWITCHING AMP FRPCCAM 15V CONV.TRANS D905 L909 Q916, 920, 925, 9244515V PANEL 13.2V IC801REGULATOR L801 L903 FDD CONT. IC803, 805 OUT B 44 1 D904 Q913 Q917, 921, 926, 927 SHOCK SENSOR SHARP6 8.5V EMERGENCY REGULATOR PANEL 6.5V IC901 L904 DET IC806 TG L802 SYSTEM CASIO2 8 Q919, 923, 930 CONTROL IC804 PANEL -15V IC802 REGULATOR BUS BUFFE IC807 L802 FLASH MEMORY RGB Q914 Q915 IC503 DECODER 4.9V L501FB C 27 SW SW DRC IC501 Q908 IC801 SWITCHING DRAM L801 SCP C 24 L903 L908 D4.9V Q912 D7014.9V L910 EVR DEC SW PANEL 4.9V 29 32 L906 IC701 IC702 OUT C 40 A4.9V D703 L701 LCD PANELQ910 UNREG2 L902RESET SW HI PROCESS IC852 FB D 32 Q909 INV SWITCHING D 4.9VL904 L907 IC703 CONV. D853 3.2V D3.2V D 3.2V D706 EEP ROM SELF TIMER SCP D 29 LED IC851 OUT D 30 IC705 DC/DC POW CONT 20 OSD IC601 CONV.L601 CTL B 21 DIA CONVERTER CTL C,D 22 Q852 PANEL 3.2V Q852 BACK LIGHT7 54 PANEL 4.9V 5 56 LED PANEL 6.5V DRIVE9 52 PANEL 13.2V 6 55 TO IC702 47 LCD DD ON PANEL -15.3V 8 53 MODE CONTROL BLOCK IC702 29 SYS DD ON A 4.9V 23 38 L851 Q852 T851 (SEE PAGE 3-11) IC702 37 CAM DD ON BL UNREG 1 60 2 59 3-16 3-17 3-18E, MVC-FD71 SECTION 4 PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS 4-1. FRAME SCHEMATIC DIAGRAM 4-1 4-2 4-3, Yellow Cyan Green White Magenta Red Blue

MVC-FD71

4-2. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS CD-196 (CCD IMAGER) PRINTED WIRING BOARD AND SCHEMATIC DIAGRAM • For printed wiring board. THIS NOTE IS COMMON FOR WIRING BOARDS AND SCHEMATIC DIAGRAMS • There are few cases that the part printed on this diagram isn’t mounted in this model. CD-196 board is 4-layer print board. However, the patterns (In addition to this, the necessary note is printed in each block) of layers 2 to 3 have not been included in the diagram. • Chip transistor C (For printed wiring boards) (Measuring conditions voltage and waveform) • b : Pattern from the side which enables seeing. • Voltages and waveforms are measured between theBE(The other layers' patterns are not indicated.) measurement points and ground when camera shoots • Through hole is omitted. color bar chart of pattern box. They are reference values • Circled numbers refer to waveforms. * and reference waveforms. CD-196 BOARD(SIDE A) CD-196 BOARD(SIDE B) • There are few cases that the part printed on diagram (VOM of DC 10 MΩ input impedance is used.). isn’t mounted in this model. • Voltage values change depending upon input impedance • Chip parts. of VOM used.) Transistor DiodeC65445645123331. ConnectionAA321BE123321321543212121Pattern box (For schematic diagrams) • All capacitors are in µF unless otherwise noted. pF : µ µF. 50V or less are not indicated except for electrolytics and tantalums. Front side of the lens • Chip resistors are 1/10W unless otherwise noted. 4 kΩ=1000Ω, MΩ=1000kΩ. 1.5mBB5• Caution when replacing chip parts. New parts must be attached after removal of chip. Be careful not to heat the minus side of tantalum capacitor, Because it is damaged by the heat. • Some chip part will be indicated as follows. 1-670-485- 1-670-485- Example C541 L452 22U 10UHCCTA A 2520 Kinds of capacitor 2. Adjust the distance so that the output waveform of Fig. a and the Fig. b can be obtain. 11 11 Temperature characteristics 05A=B 05 External dimensions (mm) BA1212C=D • Constants of resistors, capacitors, ICs and etc with XXCDCD-196 BOARD CD-196 BOARD indicate that they are not used. (SIDE A) (SIDE B) In such cases, the unused circuits may be indicated. IC401 B-2 • All variable and adjustable resistors have characteristic C401 B-2C402 B-2 curve B, unless otherwise noted. C403 B-2 • Signal name C404 B-1 XEDIT → EDIT PB/XREC → PB/REC C405 B-1 • 2 : non flammable resistor • 1 : fusible resistor H CN401 A-2 1 IC401 1 REC 4 IC401 !£ RECH 2 !¢ • C : panel designation 7.6Vp-pFig. a (CPC-9 jig TP-VG output waveform) • : B+ Line L401 B-2A ✽ • B : B– Line ✽ Q401 B-2 FC-66 • J : IN/OUT direction of (+, –) B LINE. ✽ Electron beam ( CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO,scanned frame RL-50 FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER, 6Vp-p• C : adjustment for repair. ✽ R401 B-2 (RELEASE SWITCH) DC/DC CONVERTER ) 0.025µsec • Circled numbers refer to waveforms. ✽ LCD picture frame R402 B-2 H ✽ Indicated by the color red. R403 B-2 2 IC401 3 REC 5 IC401 !™ REC CD-196 (CCD IMAGER) 4 7.6Vp-p Note : Les composants identifiés par une marque FLASH UNIT ! sont critiques pour la sécurité. Fig.b (Picture on LCD) Ne les remplacer que par une pièce portant Precautions Upon Replacing CCD Imager le numéro spécifie. • The CD-196 board mounted as a repair part is not equipped 6Vp-p When indicating parts by reference number, please with a CCD imager. 0.025µsec Note : The components identified by mark ! or include the board name. When replacing this board, remove the CCD imager from the H dotted line with mark ! are critical for safety. old one and mount it onto the new one. 3 IC401 7 REC Replace only with part number specified. PK-43 FDD INTERFACE, RGB DECODER, • If the CCD imager has been replaced, carry out all the( ) 1.5Vp-p LCD TIMING GENERATOR, MODE KEY SWITCH, BACK LIGHT adjustments for the camera section. • As the CCD imager may be damaged by static electricity from its structure, handle it carefully like for the MOS IC. In addition, ensure that the receiver is not covered with dusts H nor exposed to strong light. CCD IMAGER 4-4 4-5 4-6 CD-196,

MVC-FD71

RL-50 (RELEASE SWITCH), FC-66 (CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO, FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER, DC/DC CONVERTER) PRINTED WIRING BOARDS • For printed wiring boards. • There are few cases that the part printed on this diagram isn’t mounted in this model.— Ref. No.: RL-50 Board; 1,000 Series, FC-66 Board; 1,000 Series — FC-66 board is 6-layer print board. However, the patterns ofFC-66 BOARD (SIDE A) layers 2 to 5 have not been included in the diagram. FC-66 BOARD (SIDE B) C111 A-3 IC102 A-3 R723 F-3 • RL-50 board is 4-layer print board. However, the patterns of C103 A-2 C928 B-3 Q908 C-3 R828 G-2 R979 B-2 C112 B-3 IC104 B-3 R724 F-3 layers 2 to 3 have not been included in the diagram. C104 B-2 C929 B-4 Q909 C-3 R829 F-2 R980 B-2

RL-50 RL-50 BOARD(SIDE B) C116 A-3 IC501 D-1 R725 F-3

• Chip transistor C C107 B-1 C930 B-3 Q913 B-3 R830 G-2 R981 B-2 BOARD(SIDE A) C117 A-3 IC503 D-2 R726 E-2 C108 A-1 C931 B-4 Q915 D-3 R831 G-2 R983 B-4C119 A-3 IC601 D-3 R727 E-2 C109 B-1 C932 B-3 Q916 C-3 R832 G-2 R984 C-4 C120 A-3 IC701 E-2 B ER728 F-2 FC-66 BOARD(SIDE B) C110 A-1 C933 B-3 Q917 D-3 R860 D-4C121 A-3 IC702 E-3 R729 F-2 C113 A-1 C934 C-3 Q918 B-3 R862 D-4 SE801 G-3 1-670-484 C122 A-3 IC703 E-4 R730 F-4 C114 A-2 C935 C-4 Q919 C-4 R864 D-41-670-484 C124 A-2 IC804 F-2 R736 F-4 FC-66 BOARD(SIDE A) 2 1 C129 A-2 C936 C-4 Q920 C-2 R866 D-3 X101 A-2

A A C125 A-2 IC807 F-1 R737 F-2 C130 A-2 C937 B-3 Q921 D-3 R868 D-3 X802 D-3C126 B-2 R738 F-2 C132 B-2 C938 B-3 Q922 B-3 R869 D-3 X803 D-2

C127 B-2 L101 A-2 R739 E-2 8 C133 B-1 C939 B-3 Q923 C-4 R870 D-2C128 A-2 L501 C-2 R740 E-2 C134 B-1 C940 B-2 Q924 C-3 R880 F-2 C131 A-3 L601 C-4 R741 E-2AAC135 B-2 C944 D-3 Q925 C-3 R909 A-3 C401 B-4 L701 B-2 R742 E-343C302 C-2 C945 B-3 Q926 C-3 R910 A-3C501 D-1 L901 B-2 R743 E-2 C303 C-2 C946 B-3 Q927 C-3 R912 A-3 C502 D-1 L902 B-1 R744 E-3 C402 C-1 C947 D-4 Q928 B-2 R913 A-4 C503 E-2 L903 C-2 R745 E-2 5 C403 D-1 C948 D-3 Q929 B-2 R914 A-4B B C504 D-3 L904 C-1 R746 E-3 C404 D-1 C949 C-3 Q930 D-4 R915 A-31 C601 C-3 L905 C-1 R747 E-364C405 B-1 C950 B-2 R916 A-4 C602 C-3 L910 C-1 R749 E-4 C406 D-1 C951 D-4 R101 A-1 R917 A-3

SHUTTER C603 D-3 R751 E-4AAC407 B-1 R102 B-1 R918 A-4

C604 D-3 Q601 D-4 R752 F-2BBC408 D-2 D702 G-2 R112 A-2 R919 A-4 C605 C-4 Q602 D-4 R753 F-27KKC409 B-2 D904 B-4 R114 A-2 R920 A-4C606 D-4 Q603 D-4 R759 E-2 C410 D-1 D905 B-4 R115 B-1 R921 A-3 C607 D-4 Q703 E-3 R761 F-4 C411 C-1 D906 B-3 R116 B-1 R922 A-3

C C608 D-4 Q704 E-3 R762 F-4 C412 B-1 D907 B-3 R121 A-2 R924 A-311 C A11 C611 D-4 Q706 E-3 E BR763 F-4AEBAEBC413 D-2 R402 C-1 R925 A-3

C701 F-2 Q707 F-4 R764 F-4 C415 C-2 FB102 A-2 R403 C-1 R926 A-3 05120512C702 F-2 Q708 F-4 R765 F-4CCC416 D-2 FB103 A-2 R404 C-1 R927 A-4 C703 E-2 Q910 C-1 R769 E-4CCCCC417 C-1 R405 C-1 R928 A-4 C704 E-2 Q911 C-1 R775 F-4CSCC418 D-2 IC103 A-2 R406 C-1 R929 A-4 C706 F-2 Q912 C-1 R776 F-4 D C419 D-1 IC301 C-2 R407 D-1 R930 A-4 C707 F-2 Q914 C-1 R777 E-4 G C420 D-1 IC401 D-1 R408 D-1 R931 A-4 RL-50 BOARD C708 F-4 R778 E-3 9 14 13 C421 D-2 IC402 B-2 R409 D-1 R932 A-4(SIDE A) C709 E-4 R106 B-3 R779 E-2 C720 G-1 IC403 C-2 R410 D-1 R933 A-4 C713 E-2 R111 B-3 R780 E-2 C804 F-1 IC404 D-1 R411 C-1 R934 A-4 CN051 C-1 C714 E-4 R119 B-2 R816 G-2321C805 F-1 IC405 D-2 R412 D-1 R935 B-4 C715 E-3 R401 B-4 R817 G-2 11 C806 F-1 IC705 G-1 R413 D-1 R936 A-4S051 B-1 C716 E-2 R601 D-3 R818 G-2 C807 F-1 IC801 E-1 R414 D-2 R937 A-3 C717 E-3 R605 C-4 R819 G-2 D 10 15D45C808 F-1 IC802 F-1 R415 D-1 R938 A-3 C718 E-4 R606 D-3 R820 G-2 C809 F-2 IC803 G-4 R416 D-2 R940 A-3 C724 E-2 R610 D-4 R821 G-2 12 C810 F-1 IC805 G-2 R417 C-2 R941 A-3C725 F-4 R611 D-4 R822 G-2 C811 F-4 IC806 E-3 R418 D-1 R942 A-3 C726 F-4 R612 D-4 R823 G-2 SELF TIMER C812 F-4 IC901 A-3 R419 D-1 R943 B-4 C727 F-4 R613 D-4 R871 F-2 C813 G-4 R420 D-2 R946 B-3 C815 F-2 R614 D-4 R872 F-2 C814 G-4 L102 B-2 R422 D-2 R947 B-3 C820 G-2 R615 D-4 R873 G-1 C818 D-3 L301 C-2 R423 D-2 R948 B-3 C920 B-2 R616 D-4 R874 G-1 C819 D-4 L401 C-1 R424 D-2 R949 B-3 C921 B-2 R617 D-4 R875 G-1EE20 C821 D-4 L403 D-1 R425 D-2 R951 B-4C924 B-2 R618 D-4 R876 G-1 19 C822 F-4 L404 C-1 R426 D-2 R957 B-2 C942 C-1 R619 D-4 R877 G-1 C823 D-2 L801 F-1 R428 D-2 R958 B-2 FC-66 CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO, C943 C-2 R620 D-4 R878 G-1 C824 E-2 L802 D-4 R429 D-2 R959 A-2 RL-50 ( FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER,(RELEASE SWITCH) ) R621 D-4 R879 G-1 22 C825 D-3 L906 C-3 R701 G-2 R960 C-3 DC/DC CONVERTER CN101 A-4 R622 D-4 R904 A-1 C902 A-3 L907 C-4 R702 G-2 R961 C-3 CN401 C-4 R623 D-4 R952 C-1 C903 A-3 L908 C-3 R703 G-2 R962 D-3 CN602 G-4 R624 D-4 R953 C-1 21 C904 A-3 L909 B-3 R757 G-1 R963 D-3CD-196 (CCD IMAGER) CN901 A-1 R704 E-2 R954 C-1 C905 A-3 R802 D-2 R964 C-3 FLASH UNIT CN907 A-2 R706 F-3 R956 D-1FFC906 A-3 Q101 A-2 R804 D-2 R965 D-4 CN910 A-3 R707 F-4 R986 F-2 C908 A-4 Q102 A-2 R806 E-2 R966 C-3 R708 F-4 C909 A-3 Q103 A-2 R807 E-2 R967 C-3 D701 F-2 R709 F-4 T901 B-1 C910 A-4 Q104 A-2 R808 E-2 R968 B-2 D703 E-2 R710 E-4 C914 A-4 Q401 C-1 R809 F-1 R969 C-4 D706 D-3 R711 E-4 X701 F-4 C915 A-3 Q402 C-2 R810 F-1 R970 C-2 R712 F-3 X702 E-4 17 18 C916 B-4 Q403 D-1 R811 F-1 R971 D-3 F901 A-2 R713 F-3 16 C918 B-4 Q701 G-2 R812 F-1 R972 B-3 PK-43 ( FDD INTERFACE, RGB DECODER, F902 A-1 R714 F-3 G C919 A-3 Q702 G-2S R813 F-1D R973 C-4 LCD TIMING GENERATOR, MODE KEY SWITCH, BACK LIGHT ) F903 A-1 R715 F-2GGC922 B-4 Q801 G-2 R814 F-1 R974 D-3 F904 A-1 R717 F-2DGSC923 A-3 Q802 G-3 R815 F-1 R975 B-2 R718 F-4 C925 B-4 Q803 G-3 R825 G-4 R976 D-4 FB101 A-3 R721 F-3 1-670-482- 11 1-670-482- 11 C926 B-3 Q906 C-4 R826 G-4 R977 D-4 FB104 B-3 R722 F-3 051234051234C927 B-3 Q907 B-4 R827 G-2 R978 D-4 4-9 4-10 4-7 4-8 RELEASE SWITCH/ CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO, FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER, DC/DC CONVERTERRL-50 FC-66 C825,

MVC-FD71

FC-66 (CAMERA) SCHEMATIC DIAGRAM • See page 4-9 for FC-66 BOARD printed woring board.

FC-66 BOARD (1/8)

1 IC103 $º REC $¡ 7.6Vp-p

H

2 IC103 $™ REC $¢ 7.6Vp-p

H

3 IC102 @§ REC @¶ 1.5Vp-p

H

4 IC103 !™ REC !£ 6Vp-p 0.025µsec 5 IC103 9 REC 6Vp-p 0.025µsec 6 IC102 !§ REC 2.3Vp-p 0.025µsec 7 IC102 2-!º REC 0.025µsec 3.2Vp-p 8 IC103 $¶ REC 2.3Vp-p 36MHz CAMERA 4-12 4-13 4-14 FC-66 (1/8),

MVC-FD71

FC-66 (DRAM CONTROL) SCHEMATIC DIAGRAM • See page 4-9 for FC-66 BOARD printed wiring board. 4-15 4-16 4-17 DRAM CONTROL FC-66 (2/8),

MVC-FD71 Ver 1.1 1998. 09

FC-66 (D/A CONVERTER) SCHEMATIC DIAGRAM • See page 4-9 for FC-66 BOARD printed wiring board.

FC-66 BOARD (3/8)

9 IC601 #¶-$¢ REC/PB !¢ IC601 !ª REC/PB 0.025µsec 3.2Vp-p H 0.8Vp-p !º IC601 $§ REC/PB !∞ IC601 !¢ 3.2Vp-p V 1Vp-p

H

!¡ IC601 $∞ REC/PB !§ CN602 !¶ REC/PB 3.2Vp-p H 1Vp-p

H

!™ IC601 $¶ REC/PB !¶ CN602 !ª REC/PB 3.1Vp-p

H

H 0.8Vp-p !£ IC601 @£ REC/PB !• CN602 @¡ REC/PB 1Vp-pHH0.8Vp-p D/A CONVERTER 4-18 4-19 4-20 FC-66 (3/8),

MVC-FD71

FC-66 (CAMERA SERVO) SCHEMATIC DIAGRAM • See page 4-9 for FC-66 BOARD printed wiring board. 4-21 4-22 4-23 CAMERA SERVO FC-66 (4/8),

MVC-FD71

FC-66 (FDD CONTROL) SCHEMATIC DIAGRAM • See page 4-9 for FC-66 BOARD printed wiring board.

FC-66 BOARD (5/8)

!ª IC801 *£ REC/PB 3.2Vp-p 16MHz @º IC806 ⁄̀‚‡ PB 3.2Vp-p 15MHz FDD CONTROL 4-25 4-26 4-27 4-28 FC-66 (5/8),

MVC-FD71

FC-66 (MODE/SYSTEM CONTROL), (EVR DECODER) SCHEMATIC DIAGRAMS • See page 4-9 for FC-66 BOARD printed wiring board.

FC-66 BOARD (6/8)

@¡ IC702 $º REC/PB 20MHz 0.6Vp-p @™ IC702 %£ REC/PB 32.7kHz 3.0Vp-p 4-29 4-30 4-31 4-32 MODE/SYSTEM CONTROL EVR DECODER FC-66 (6/8) / FC-66 (7/8),

MVC-FD71

FC-66 (DC/DC CONVERTER), RL-50 (RELEASE SWITCH) SCHEMATIC DIAGRAMS • See page 4-9 for FC-66 BOARD and 4-7 for RL-50 BOARD printed wiring boards. DC/DC CONVERTER RELEASE SWITCH 4-34 4-35 4-36 FC-66 (8/8) / RL-50,

MVC-FD71 PK-43 (FDD INTERFACE, RGB DECODER, LCD TIMING GENERATOR, MODE KEY SWITCH, BACK LIGHT) PRINTED WIRING BOARD • For printed wiring board.

• There are few cases that the part printed on this diagram isn’t mounted in this model. PK-43 BOARD (SIDE A) — Ref. No.: PK-43 Board; 2,000 Series — PK-43 board is 4-layer print board. However, the patterns of layers 2 to 3 have not been included in the diagram. PK-43 BOARD (SIDE B) BH701 E-1 R965 E-5 • Chip transistorC45C601 E-7 Q856 B-1 R871 D-1 *R966 E-6 C602 D-6 Q857 D-1 R872 D-1 BZ701 E-7 R967 E-5 C603 D-6 Q858 D-1 R873 D-2BE321R968 E-5 C604 D-7 Q859 D-1 R874 D-2 C851 D-7 R969 E-5 FC-66 C605 E-7 Q860 B-1 *R901 E-5 C852 B-7 CAMERA, DRAM CONTROL, D/A CONVERTER, CAMERA SERVO,RL-50 C606 F-7 Q862 D-1 R905 D-4 FDD CONTROL, MODE/SYSTEM CONTROL, EVR DECODER, C854 C-7 RV701 A-7 PK-43 BOARD(SIDE A) ( PK-43 BOARD(SIDE B)(RELEASE SWITCH) DC/DC CONVERTER ) C701 E-2 Q903 E-3 *R906 E-4 C855 C-7 C702 E-1 Q904 E-3 R908 D-4 C857 D-7 S701 E-5 C703 E-1 Q905 F-3 R912 E-4 C858 D-7 S702 D-6 CD-196 ZOOM C801 E-6 Q906 E-3 R913 F-4 C861 B-6 S703 E-3 (CCD IMAGER) FLASH UNITWTC802 E-6 R915 F-4 C862 B-7 S704 E-4 C803 E-6 R601 F-7 R916 E-4 C866 C-7 S705 D-3 C804 E-6 R602 E-7 R918 F-4 C903 E-4 S706 D-2AAC805 E-6 R603 E-7 R920 D-4 C906 E-4 S707 E-3 C806 D-5 R604 E-7 R921 E-4 C907 E-4 S708 E-4 C807 F-5 R605 E-6 R922 E-4 C908 E-5 S709 D-1 C808 F-5 R606 E-7 R924 E-4 C915 E-5 S710 C-1 C810 E-5 R607 E-7 R927 E-4 C917 D-6 PK-43 C811 E-5 R608 E-7 R929 E-4 C920 D-4 T851 C-7 ( FDD INTERFACE, RGB DECODER, LCD TIMING GENERATOR, C812 E-5 R610 E-7 R930 E-4 C926 E-4 MODE KEY SWITCH, BACK LIGHT ) C813 E-6 R612 E-7 R931 E-3 C814 E-6 R613 E-6 R932 E-3 CN603 F-3321C815 E-5 R614 E-7 R933 F-3 CN802 D-1BBC853 B-1 R615 E-7 R934 F-3 C856 B-1 R618 E-7 R935 E-3 D701 E-6 C859 B-1 R619 E-7 *R936 E-354D702 D-3 C863 B-1 R620 D-6 *R937 E-3 D903 E-4 C865 D-1 R621 D-6 R940 E-3 D904 D-565C867 D-1 R622 D-6 R945 E-3 *C901 D-5 R623 D-7 R946 E-3 IC851 D-7 4 C902 D-5 R624 D-7 R947 E-3 IC903 F-4 C904 D-5 R625 D-7 R948 E-3 3 C905 E-4 R626 D-7 R949 E-3 L851 B-7 C909 F-4 R627 D-7 *R950 E-3 L852 B-7 LCD 210 C911 C913 R628 D-7 *R951 E-3 L853 B-7 C BACK LIGHT1CC913 D-4 R629 E-6 *R952 E-3 L905 E-4 OFF ON C916 E-3 R630 E-6 *R953 E-3 C918 E-2 R631 D-6 *R954 E-2 Q851 D-7 C919 D-4 R632 D-6 *R955 E-2 Q852 D-7 *C921 E-3 R702 E-2 R956 E-2 Q853 C-7 BRIGHT 11 C925 D-4 R709 E-1 *R957 E-2 R710 E-1 R958 D-3 R701 E-5 [-] BRIGHT[+] 5 4 CN601 F-7 R713 E-1 *R959 D-3 R703 D-3 1 CN602 F-7 R714 E-1 R961 E-2 R705 E-5123CN851 D-2 R715 E-1 *R970 E-3 R706 E-3 CN901 D-3 R801 D-5 *R971 E-3 R707 E-4 D POWER D R804 E-5 *R972 E-3 R708 D-2 CONTROLPLAY/CAMERA D852 C-1 R805 E-6 R973 D-4 R711 D-1 D853 D-2 R806 E-5 R974 E-4 R712 E-4 PLAY CAMERA D854 A-1 R812 E-6 R975 E-4 R716 D-1 UP SET OFFFLASH D905 D-4 R813 E-5 R978 F-4 R717 D-1 CHARGE R814 E-5 R979 F-4 R852 C-7 ON IC601 D-7 R815 E-6 R980 E-4 R853 C-7 FLASH R854 D-7 7 IC801 D-6 R816 F-5 R981 E-4PICTURE LEFT RIGHT 6 IC802 E-5 R822 F-5 R856 D-7 EFFECT 9 IC852 D-1 R823 E-5 R859 D-7 PROGRAM AE ACCESS IC901 E-4 R826 F-6 *R902 E-4 E DOWN E IC902 F-4 R827 E-5 R903 D-3 10 4 R828 F-5 R914 E-4532L601 E-7 R855 B-1 R926 E-4 DISPLAY L701 E-2 R857 B-1 R938 F-5 L801 F-5 R858 B-1 R939 F-5 8 L901 D-5 R860 D-1 R941 D-6 L902 D-5 R861 D-1 R942 D-6 L903 D-5 R862 C-1 R943 E-5 *L904 D-5 R863 C-1 R944 E-4 R864 D-1 R960 D-5 F 1-670-483 1-670-483- 11 F 1-670-483 Q701 E-1 R865 C-1*R962 E-6 1-670-483- 11 Q702 E-1 R867 B-1 *R963 E-6 Q854 B-1 R868 B-1 R964 E-6 051234567051234567Q855 D-1 R870 D-1 Note: * mark is CASIO made LCD panel model only. Note: * mark is CASIO made LCD panel model only. 4-40 4-37 4-38 4-39 FDD INTERFACE, RGB DECODER, LCD TIMING GENERATOR, MODE KEY SWITCH, BACK LIGHT PK-43,

MVC-FD71

PK-43 (FDD INTERFACE) SCHEMATIC DIAGRAM • See page 4-37 for PK-43 BOARD printed wiring board. 1 IC601 $™ REC/PB 5Vp-p 4MHz FDD INTERFACE 4-42 4-43 4-44 PK-43 (1/5),

MVC-FD71

PK-43 (RGB DECODER) SCHEMATIC DIAGRAM • See page 4-37 for PK-34 BOARD printed wiring board.

PK-43 BOARD (2/5)

2 IC802 9 REC/PB 0.6Vp-p

H

3 IC802 8 REC/PB 0.5Vp-p

H

4 IC802 !º REC/PB H 0.5Vp-p 5 IC802 @º REC/PB 4Vp-p

H

6 IC802 @™ REC/PB 4.2Vp-p

H

7 IC802 @¢ REC/PB 4.3Vp-p

H

8 IC802 @• REC/PB @ª 4.9Vp-p 40µsec 4-45 4-46 4-47 RGB DECODER PK-43 (2/5),

MVC-FD71

PK-43 (LCD TIMING GENERATOR) SCHEMATIC DIAGRAM • See page 4-37 for PK-43 BOARD printed wiring board.

PK-43 BOARD (3/5)

9 IC901 #¢ REC/PB 3.2Vp-p

V

!º IC901 #¶ REC/PB 3.2Vp-p

H

LCD TIMING GENERATOR 4-48 4-49 4-50 PK-43 (3/5),

MVC-FD71

PK-43 (MODE KEY SWITCH) SCHEMATIC DIAGRAM • See page 4-37 for PK-34 BOARD printed wiring board. 4-51 4-52 MODE KEY SWITCH PK-43 (4/5),

MVC-FD71

PK-43 (BACK LIGHT) SCHEMATIC DIAGRAM • See page 4-37 for PK-34 BOARD printed wiring board.

PK-43 BOARD (5/5)

!¡ IC851 1 REC/PB 5.5Vp-p 2.1µsec BACK LIGHT 4-53 4-54E PK-43 (5/5),

MVC-FD71 SECTION 5 ADJUSTMENTS

5-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT 1-1-1. List of service tools Oscilloscope Regulated power supply Vectorscope Digital voltmeter Frequency counter AC power adaptor (BC-V615) Ref. No. Name Parts Code Usage J-1 Filter for color temperature correction (C14) J-6080-058-A Auto white balance adjustment/check White balance adjustment/check J-2 ND filter 1.0 J-6080-808-A White balance check ND filter 0.3 J-6080-818-A White balance check J-3 Pattern box PTB-450 J-6082-200-A J-4 Color chart for pattern box J-6020-250-A J-5 Siemens star J-6080-875-A For checking the flange back J-6 Adjustment remote commander (RM-95 upgraded) Note2 J-6082-053-B J-7 Clear chart J-6080-621-B White balance adjustment. J-8 CPC-9 (12-pin/18-pin, 0.5 mm) J-6082-393-B LANC signal, R.G.B. signal check. J-9 Extension cable J-6082-427-A FDD UNIT-PK-43 board J-10 Alignment disk (Two disks as a pair) TFD2-1(+) 8-967-990-01 Dynamic inspection disk with LCD adjustment signal TFD2-2(–) 8-967-990-11 J-11 Personal computer PC with Windows95 installed J-12 Cleaning disk (OR-D29WA) 8-960-009-39 FDD head cleaning *Note 1 Cleaning disk Available on market Note 1: Usage and operating note Note 2: If the microprocessor IC in the adjusting remote One or two seconds of momentary use of cleaning disk is commander is not the new microprocessor (UPD7503G- sufficient such that FD is accessed momentarily by system C56-12), the pages cannot be switched. control when the main power is turned on. After cleaning, In this case, replace with the new microprocessor (8-759- insert a FD for playback. When cleaning is insufficient, 148-35). use a cleaning disk again. Caution: Avoid using a cleaning disk excessively. Head can be broken. J-1 J-2 J-3 J-4 J-5 J-6 J-7 J-8 J-9 J-10 J-11 J-12 Fig.5-1-1. 5-1, 1-1-2. Precautions 3) White pattern (Standard picture frame) 1. Switch settings Remove the color bar chart from the pattern box and adjust the Adjust the switches to the following positions. camera setup until the white pattern picture frame is the same 1) PLAY/CAMERA switch size and same position as the color bar chart (the standard (PK-43 board S708) ··············································· CAMERA picture frame). 2) FLASH (PK-43 board S705) ···········································OFF 3) PROGRAM AE (PK-43 board S707) Turn OFF all marks from the LCD Pattern box 2. Adjustment sequence Adjust in the given order. 3. Subject Front side of the lens 1) Set the camera and pattern box as shown in Fig. 5-1-2. 2) Color bar chart (Standard picture frame) 1.5m • Adjust the picture frame as shown in Fig. 5-1-3. • Adjust camera zooming and direction until the camera output waveform on the oscilloscope shown in Fig. 5-1-3 (a) and the color picture on the LCD shown in Fig. 5-1-3 (b) have been acquired. • Maintain this setup until adjustment is complete. Fig. 5-1-2 Horizontal rate Electron beam scan frame size A=B

B A

C=D

C

D LCD picture frame Fig. b Confirm on LCD (Underscanned display) H H Adjust direction and zoom of camera so that the picture frame Fig. a CPC-9 jig TP-VG output waveform is adjusted as specified by Fig. a and Fig. b. Fig. 5-1-3 4) Chart for flange back adjustment Join together a piece of white A0 size paper (1189mm × 841 mm) and a piece of black paper to make the chart shown in Fig. 5-1-4. White 841mm Note: Use a non-reflecting and non-glazing vellum paper. The Black size must be A0 or larger and the joint between the white and black paper must not have any undulations. 1189mm Fig. 5-1-4 5-2 Yellow Cyan Green White Magenta Red Blue Yellow Cyan Green White Magenta Red Blue, 1-1-3. Preparations Note 1: Refer to “2. Disassembly” for details of how to remove 1) Connect the adjustment equipment as shown in Fig. 5-1-5. the cabinet and the respective boards. Note 2: Removal of the lens block and FC-66 board is not necessary if only adjustments are to be made. AC IN BC-V615 FLASH UNIT RL-50

BOARD

CN051 LENS UNIT CD-196

BOARD

CN401 CN907 CN910 FDD UNIT CN901 CN101 CN401 + – BATTERY FC-66 TERMINAL BOARD Extension cable (J-6082-427-A) Refer to page 5 CN602 [How to connect the extension cable] CN011 CN013 CN012 CN603 CN602 CN901 KP-43 BOARD CN601 CN851 CN802 RM-95 2.5inch LCD Adjustment Remote PANEL Commander BACK LIGHT Note 3: In changing data, wait for more than CPC-9 5 seconds after the set was turned on, (J-6082-393-B) then change the data. Fig. 5-1-5. Note 4: When performing the adjustments only, the cabinet removal is not needed. Open the lithium battery lid and connect the CPC-9 jig as shown in the right figure. Note 5: Connect the GND terminal to Floppy disk drive unit frame when check the RF signals waveform.

CPC

5-3, 1-1-4. Discharge of flashlight power supply The capacitor which is used as the power supply of flashlight is charged with 200 V to 300 V voltage. Discharge this voltage before starting adjustment in order to protect service engineers from electric Capacitor shock during adjustment . Discharge procedure

R

1. Turn OFF the flash switch by pressing the switch S705 on the PK-43 board which turns OFF the flash charging lamp. 2. Fabricate the discharging jig as shown in Fig. 5-1-6 locally by yourself. Connect the discharging jig to the positive (+) and negative (-) terminal of the flash voltage charge capacitor. R : 1kΩ 1WFlash circuit board (Part code No. 1-215-869-11) Allow ten seconds to discharge the voltage. Fig. 5-1-6 1-1-5. Adjustment remote commander (RM-95 upgraded) To perform adjustment, the adjustment data stored in the non-volatile Display on the Bit values memory must be rewritten using the adjustment remote commander adjustment bit3 bit2 bit1 bit0 (RM-95 upgraded). remote or or or or The adjustment remote commander uses the remote commander commander bit7 bit6 bit5 bit4 signal line (LANC) to interactively communicate with the merchandise. The page, address and up/down command data are00000sent from the adjustment remote commander to the merchandise. 10001In return, the page, address and data are sent to the adjustment remote20010commander from the merchandise. 30011401001. Using the adjustment remote commander501011) Connect the adjustment remote commander to the LANC terminal (CPC jig). 601102) Set the NOR-ADJ (or HOLD) switch of the adjustment remote70111commander to the “ADJ” (or ON) (service) position. A81000If the adjustment remote commander is correctly connected, 91001the adjustment remote commander’s LED will show the display A (A) 1010as shown in Fig. 5-1-7. B ( ) 10113) Bit value discrimination b It is necessary to discriminate between the bit values with the C (C) 1100data displayed on the adjustment remote commander for all D (d) 1101following items. Identify whether the bit value is “1” or “0” B E (E) 1110with the use of the following diagram. F (F) 1111Display on the adjustment remote commander (Example) If “8E” is displayed on the adjustment remote commander, the bit values for bit7 to bit4 are shown in the A column, and the bit values for bit3 to bit0 are shown in the B column. Address Page bit3 to bit0 discrimination bit7 to bit4 discrimination Fig. 5-1-7 5-4, 4) The adjustment remote controller is operated as follows: • Changing the address • Changing the page The address increases when the FF ()) button is pressed, The pages increase when the EDIT SEARCH (+) button is and decreases when the REW (0 ) button is pressed. pressed and decrease when the EDIT SEARCH (–) button is Altogether there are 256 addresses from address “00” to address pressed. Altogether there are 16 pages from page “0” to page “FF”. Some addresses, which are not used during adjustment, “F”. do not appear. • Taking note the already-stored adjustment data Hexadecimal The previous adjustment can be erased if the adjustment remote notation0123456789ABCDEFcommander is incorrectly handled. To prevent this, it is recommended that all the stored adjustment data be noted down LCD display0123456789AbCdEFon the attached page F address list. • Changing the data (Data setting) Decimal The data increases when the PLAY ( ) button is pressed, notation after012345678910 11 12 13 14 15 and decreases when the STOP (p) button is pressed. Altogether conversion there 256 data from data “00” to data “FF”. • Storing the data Press the PAUSE button to store the adjustment data (page F) into the non-volatile memory. (If the PAUSE button is not pressed after completing the [Sequence of Service Models Using the Adjustment Remote adjustment, the new adjustment data will not be stored in the Commander] non-volatile memory.) 5) After completing all adjustments, turn off the main power START Normal mode supply (7.2 V) once. This releases the adjustment mode (all modes except for page F). Set the NORM - ADJ (HOLD) switch ADJ (ON) Enters the service mode Press the EDIT SEARCH +/- button Page changed Refer to the memory map Press the FF/REW button Address changed < When changing adjustment data > Press the PLAY/ Data changed The EVR value (RAM) is changed to the new data. STOP button (But the changed data is not stored in the EE PROM.) Press the PAUSE button Date stored Data stored in EE PROM Set the NORM - ADJ (HOLD) switch NOR (OFF) Command Name Command Function Normal LANC Command Page Up Page + 1 Edit Search + Page Down Page – 1 Edit Search – Direct Page Set Sets the specified page Event Clear Address Up Address + 1 Fast Forward Address Down Address – 1 Rewind Data Up Data + 1 Play Back Data Down Data – 1 Stop Store Stores data in the EE PROM. Pause 2. Precautions when using the adjustment remote commander Mishandling of the adjustment remote commander may erase the correct adjustment data which has already been stored in the memory. To prevent this, it is recommended that all adjustment data is noted down on the attached page F address list before starting adjustments in addition to all new adjustment data after the completion of each adjustment step. 5-5, 1-1-6. Data Processing In some adjustment items, data appears in hexadecimal numbers on the DDS display or on the adjustment remote commander. Maintenance engineers are expected to convert the displayed hexadecimal numbers to the corresponding decimal numbers using the following conversion table. Make a required calculation described in each adjustment item. Then re-convert the result of calculation back from the decimal numbers to the corresponding hexadecimal numbers using the following conversion table. Hexadecimal-decimal Conversion Table 2 Lower digit of hexadecimal0123456789ABCDEFUpper digit (A) (b) (c) (d) (E) (F) of hexadecimal0012345678910 11 12 13 14 15 1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 3 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 4 64 65 66 67 68 69 70 71 72 73 74 77 76 77 78 79 5 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 6 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 7 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 8 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 9 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 A (A) 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 1751B(b) 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 C (c) 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 D (d) 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 E (E) 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 F (F) 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 Note : The characters shown in the parenthesis ( ) shown the display on the adjustment remote commander. (Example) If the DDS display or the adjustment remote commander shows BD (bd); Because the upper digit of the adjustment number is B (b), and the lower digit is D (d), the meeting point “189” of 1 and 2 in the above table is the corresponding decimal number. Table. 5-1-1 5-6, 1-2. INITIALIZATION OF E AND F PAGE DATA 3. F page table 1. Initialization of E and F page data Note 1: “Fixed data-1”: Initialized data (refer to “1. Initialization Note 1: All data on pages E and F are initialized, if “initialization of E and F page data”) of E and F page data” is executed. (Only either page “Fixed data-2”: Changed data (refer to “2. Change of E cannot be initialized.) and F page data”) Note 2: This set must be readjusted in all items, if E and F page Note 2: For the asterisk *, refer to “1-4. LCD System Adjustment”. data were initialized. Adjustment page F Address Initial Remark Adjustment address 00 - FF value Adjustment page E 00 to 0F Adjustment address 00 - FF 10 Fixed data-1 Initialization procedure: 11 (Initialized data) 1) Set data: 01 to page: 0, address: 01. 12 Fixed data-2 2) Set data: 2D to page: 0, address: 00. 13 Fixed data-1 3) Set data: 2D to page: 3, address: 01, and press the PAUSE button 14 (Initialized data) on the adjustment remote commander. 15 4) After more than 3 seconds, confirm that the data on page: 3, 16 address: 00 is “00”. 5) Set data: 00 to page: 0, address: 01. 17 6) Execute “change of E and F page data”. 18 80 Battery down adj. 19 88 2. Modification of F, E page data 1A AD If the F, E page data has been initialized, change the data of the 1B C2 “Fixed data-2” address shown in the following tables by manual 1C CD input. 1D Fixed data-1 Modifying Method: 1E (Initialized data) 1) Before changing the data, select page: 0, address: 01, and set 1F data: 01. 20 Fixed data-2 2) New data for changing are not shown in the tables because 21 they are different in destination. When changing the data, copy the data built in the same model. 22 Note: If copy the data built in the different model, the 23 camcorder may not operate. 24 Fixed data-1 3) When changing the data, press the PAUSE button of the 25 (Initialized data) adjustment remote commander each time when setting new 26 Fixed data-2 data to write the data in the non-volatile memory. 27 4) Check that the data of adjustment addresses is the initial value. If not, change the data to the initial value. 28 5) After changing the data, select page: 0, address: 01, and set 29 data: 00. 2A Fixed data-1 2B (Initialized data) 2C 2D 2E 2F 30 Åñ Bright adj. 31 Fixed data-1 32 (Initialized data) 33 Åñ White balance adj. 34 Åñ 35 Åñ CONTRAST adj. 36 Åñ VCO adj. 37 Åñ V-COM adj. 38 Åñ D RANGE adj. 39 Åñ V-COM level adj. 3A Fixed data-1 3B Åñ Fixed data-2 3C Fixed data-1 3D Fixed data-2 3E Fixed data-1 3F (Initialized data) 5-7, Address Initial Remark Address Initial Remark value value 40 Fixed data-2 71 Fixed data-1 41 72 (Initialized data) 42 Fixed data-1 73 43 (Initialized data) 74 44 75 45 76 46 77 47 78 48 79 49 7A 4A Fixed data-2 7B 4B Fixed data-1 7C 4C (Initialized data) 7D 4D 7E 4E 7F 4F 80 50 81 51 82 52 83 53 84 54 85 55 86 56 87 57 88 58 89 59 8A 5A 8B 5B 8C Fixed data-2 5C 8D Fixed data-1 5D 8E (Initialized data) 5E 8F 5F 90 60 91 61 92 62 93 63 94 64 95 65 96 66 97 67 98 68 99 69 9A 6A 9B 6B 9C 6C 9D 6D 9E 6E 9F 6F A0 Fixed data-2 70 A1 5-8, Address Initial Remark Address Initial Remark value value A2 Fixed data-1 D3 89 Auto white balance adj. A3 (Initialized data) D4 59 A4 D5 Fixed data-1 A5 D6 (Initialized data) A6 Fixed data-2 D7 A7 D8 A8 D9 A9 Fixed data-1 DA AA (Initialized data) DB AB DC AC DD AD DE AE DF AF E0 B0 E1 B1 E2 B2 E3 B3 E4 B4 E5 B5 E6 B6 CD Flange back adj. E7 B7 19 E8 B8 92 E9 B9 21 EA BA 12 EB BB 14 EC BC Fixed data-1 ED BD (Initialized data) EE BE 00 Flange back adj. EF BF 00 F0 C0 41 F1 C1 00 F2 C2 19 F3 C3 00 F4 C4 2E F5 C5 00 F6 C6 Fixed data-1 F7 C7 89 HALL adj. F8 C8 79 F9 C9 Fixed data-1 FA CA 98 Light level adj. FB CB 9A FC CC 10 AWB reference data input FD CD 2D FE CE 70 FF CF 41 D0 Fixed data-1 D1 Fixed data-2 D2 5-9, 4. E page table Note 1: “Fixed data-1”: Initialized data (refer to “1. Initialization of E and F page data”) Address Initial Remark “Fixed data-2”: Changed data (refer to “2. Change of E value and F page data”) 2F Fixed data-1 30 (Initialized data) Address Initial Remark 31 value 32 00 Fixed data-1 33 01 (Initialized data) 34 02 35 03 36 04 37 05 38 06 39 07 3A Fixed data-2 08 3B Fixed data-1 09 3C (Initialized data) 0A 3D 0B 3E 0C 3F 0D 40 0E 41 0F 42 10 43 11 Fixed data-2 44 12 Fixed data-1 45 13 (Initialized data) 46 14 47 15 48 Fixed data-2 16 49 17 4A Fixed data-1 18 4B (Initialized data) 19 4C 1A 4D 1B 4E 1C 4F 1D 50 1E 51 1F 52 20 53 21 54 22 55 23 07 HUE GAIN adj. 56 24 E2 57 25 FC 58 26 FF 59 27 F3 5A 28 24 5B 29 16 5C 2A 06 5D 2B Fixed data-1 5E 2C (Initialized data) 5F 2D Fixed data-2 60 2E 61 5-10, Address Initial Remark Address Initial Remark value value 63 Fixed data-1 97 Fixed data-1 64 (Initialized data) 98 (Initialized data) 65 99 66 9A 67 9B 68 9C Fixed data-2 69 9D Fixed data-1 6A 6B 6C 6D 6E 6F 70 Fixed data-2 73 Fixed data-1 74 (Initialized data) 77 Fixed data-2 78 Fixed data-1 79 (Initialized data) 7A 7B 7C 7D 7E 7F 8A 8B 8C 8D 8E 8F 92 Fixed data-2 93 Fixed data-1 94 (Initialized data) 5-11, 1-3. CAMERA SYSTEM ADJUSTMENTS 3. HALL adjustment This adjustment sets the amplifier gain and offset to detect the iris 1. Adjustment points when major parts have been position of the lens. If disordered, the iris will oscillate or the indoor- replaced outdoor white balance will be faulty. When the CCD imager or lens block is replaced, adjust the items Subject Any subject indicated by ® in the following table. Measurement point DDS display on LCD screen When the CCD When the lens Measuring equipment imager is replaced block is replaced Adjustment page F HALL adjustment ® Adjustment address C7, C8 Flange back adjustment ® ® When data on page: 2, address: 01 is 01, Color reproduction ® ® (Note 1) adjustment Displayed data is 12 to 16. Auto white balance Specification value ® ® When data on page: 2, address: 01 is 03, reference data input (Note 1) Auto white balance Displayed data is 76 to 7A. ® ® adjustment Note 1: The PAUSE button on the adjustment remote commander Note: The above described table is applied to MVC-FD71 model. must be pressed. 2. Power supply voltage check (FC-66 board) Adjustment procedure: Subject Any subject 1) Set data: 01 to page: 0, address: 01. Measuring equipment Digital voltmeter 2) Set data: 03 to page: 0, address: 03. D3.2 V check 3) Set data: 03 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. Measurement Point CN401 1 Pin 4) Set data: 40 to page: F, address: C7, and press the PAUSE button (CN401 !• Pin: GND) on the adjustment remote commander. Specification Value 3.20 ± 0.1 Vdc 5) Read DDS displayed data (Note 2), and assume it as W2. CAM15 V check Note 2: Lower 2 digits displayed at the lower right of LCD screen. Measurement Point CN101 8 Pin 00 00 XX (CN101 4 Pin: GND) nW2 6) Set data: 30 to page: F, address: C7, and press the PAUSE button Specification Value 15.00 ± 0.4 Vdc on the adjustment remote commander. CAM –5.5 V check 7) Read DDS displayed data, and assume it as W1. Measurement Point CN101 5 Pin 8) Set data: 01 to page: 2, address: 01, and press the PAUSE button (CN101 4 Pin: GND) on the adjustment remote commander. Specification Value –5.5 + 0.2 Vdc 9) Set data: 30 to page: F, address: C7, and press the PAUSE button– 0.3 on the adjustment remote commander. 10) Read DDS displayed data, and assume it as K1. Check procedure 11) Set data: 40 to page: F, address: C7, and press the PAUSE button 1) Check that all power supply voltages satisfy the specified value. on the adjustment remote commander. 12) Read DDS displayed data, and assume it as K2. 13) Convert W1, W2, K1, and K2 into decimal numbers to get W1’, W2’, K1’, and K2’ (see Table 5-1-1. Hexadecimal-Decimal Conversion table). 14) Calculate X1’ with the formulas given below (calculate decimal numbers). A’=W2’+K1’-W1’-K2’ ... Formula 1 B’=W1’-K1’ ... Formula2X’= 1600+(48xA’)-(16xB’)1 ... Formula 3 A’ 15) Convert X1’ into hexadecimal number to get X1. (Round off the decimal place.) 16) Set data: X1 to page: F, address: C7, and press the PAUSE button on the adjustment remote commander. 17) Set data: 01 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. 18) Change the data on page: F, address: C8, so that DDS displayed data is “14”. 19) Press the PAUSE button on the adjustment remote commander. 20) Set data: 03 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. 5-12, 21) Read DDS displayed data, and assume it as W0. If W0 is in a 4. Flange back adjustment rage of “76 to 7A”, perform “processing after adjust-ment The flange back of inner focus lens is adjusted auto-matically. If finished”. If out of the range, make the following adjustment. shifted, the AUTO FOCUS and MANUAL FOCUS aredisordered. 22) Convert W0 into decimal number to get W0’. Flange back adjustment chart 23) Calculate X2’ with the formulas given below (calculate decimal Subject (2 m ± 5 mm position from lens front) numbers). (Illuminance: 250 ± 50 lux) C’=W0’+K1’-W1’-20 ... Formula 4 Measurement point Operation check on LCD screen X ’= (100-B’)x(X1’-48)+(48xC’) Measuring equipment 2 ... Formula 5 C’ Adjustment page F (X1’ is obtained from formula 3) Adjustment address B6 to BB, BE to C5 24) Convert X2’ into decimal number to get X2. (Round off the decimal place.) Adjustment procedure: 25) Set data: X2 to page: F, address: C7, and press the PAUSE button 1) Confirm that the center of flange back adjustment chart on the adjustment remote commander. coincides with the center of image screen with the zoom lens 26) Change the data on page: F, address: C8, so that DDS displayed at the TELE position and WIDE position respectively. data is “78”. 2) Set data: 01 to page: 0, address: 01. 27) Press the PAUSE button on the adjustment remote commander. 3) Make sure that the data on page: F, address: B6 to BB, BE to 28) Set data: 01 to page: 2, address: 01, and press the PAUSE button C5 are initial values listed in table below. on the adjustment remote commander. Address Data Address Data Address Data 29) Confirm that DDS displayed data is in a range of “12 to 16”. B6 CD BE 00 C4 2E Processing after adjustment finished: B7 19 BF 00 C5 00 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button B8 92 C0 41 on the adjustment remote commander. B9 21 C1 00 2) Set data: 00 to page: 0, address: 03. BA 12 C2 19 3) Set data: 00 to page: 0, address: 01. BB 14 C3 00 4) Confirm that the data on page: 2, address: 02 is “00”. 5) Set data: 13 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. 6) Set data: 15 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. (The adjustment data are automatically entered to page: F, address: B6 to BB, BE to C5.) 7) Confirm that the data on page: 2, address: 02 is “01”. Processing after adjustment finished: 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. 2) Turn off the main power supply (7.2 V). 5-13, 5. Flange back check 6. Picture frame setting Siemens Star Subject Color bar chart standard picture frame Subject (2 m position from lens front) Measurement point Test point (VG) of CPC-9 jig (Illuminance: about 200 lux) Measuring equipment Oscilloscope and LCD screen Measurement point Check on LCD screen Specification value A=B, C=D, t=0 ± 0.1 msec Measuring equipment Specification value Focus is in order at TELE position and Switch setting: WIDE position 1) AUTO FOCUS/MANUAL ... MANUAL FOCUS Switch setting: Setting procedure: 1) AUTO FOCUS/MANUAL ... AUTO FOCUS 1) Adjust the focus using the focus knob. 2) Adjust direction and zoom of camera so that the picture frame Note 1: When the AUTO FOCUS is turned on, whether the focus is adjusted as specified by Fig. 5-1-8 and Fig. 5-1-9. is in order or disordered can be judged from the LCD 3) Write down markings on the picture frame on the monitor display . screen. If the “color bar chart standard picture frame” or “white ”r“ r“ pattern standard picture frame” is specified in the following Focus is disordered adjustment items, obtain this picture frame. Focus is in order Confirm with an oscilloscope (TP-VG of CPC-9 jig) Checking procedure: Horizontal rate 1) Place the Siemens Star at2mposition from the front face of lens. A=B 2) Reduce the illuminance of lighting to the Siemens star to the BA extent that noise does not appear on the LCD screen, so as to C=D make the iris open. C

D

3) Shoot the Siemens Star with the zoom lens at TELE position. 4) Turn on the AUTO FOCUS. 5) Confirm that the focus is in order. (Note 1) 6) Set data: 10 to page: 2, address: 21, and press the PAUSE button on the adjustment remote commander. 7) Shoot the Siemens Star with the zoom lens at WIDE position. 8) Confirm that the focus is in order. Processing after checking finished: 1) Set data: 00 to page: 2, address: 21, and press the PAUSE buttonHHon the adjustment remote commander. Fig. 5-1-8 2) Set data: 00 to page: 0, address: 03. Vertical rate t =0 ± 0.1msec

V

Fig. 5-1-9 Confirm on LCD (underscanned display) Color bar chart picture frame LCD picture frame Fig. 5-1-10 5-14, 7. Light level adjustment 8. Auto white balance reference data input Clear chart Clear chart Subject (Shoot with color bar standard picture Subject (Shoot with color bar standard picture frame) frame) Adjustment page F Adjustment page F Adjustment address CA, CB Adjustment address CC to CF Note 1: The picture frame must be already set. Note: The data on page: 2, address: 02 must be “00”. Note 2: The data on page: 2, address: 02 must be “00”. (Turn off/on the power, if data is “01”.) (Turn off/on the power, if data is “01”.) Adjustment procedure: Adjustment procedure: 1) Set data: 01 to page: 0, address: 01. 1) Set data: 01 to page: 0, address: 01. 2) Set data: 0A to page: E, address: 11, and press the PAUSE 2) Set data: 58 to page: 2, address: 10, and press the PAUSE button button on the adjustment remote commander. on the adjustment remote commander. 3) Set data: 58 to page: 2, address: 10, and press the PAUSE button 3) Turn off the HOLD switch on the adjustment remote on the adjustment remote commander. commander. 4) Turn off the HOLD switch on the adjustment remote 4) After more than 2 seconds, turn on the the HOLD switch on commander. the adjustment remote commander. 5) After more than 2 seconds, turn on the the HOLD switch on 5) Shoot the clear chart with the color bar standard picture frame. the adjustment remote commander. 6) Set data: 0D to page: 2, address: 01, and press the PAUSE button 6) Shoot the clear chart with the color bar standard picture frame. on the adjustment remote commander. 7) Set data: 11 to page: 2, address: 01, and press the PAUSE button (The adjustment data are automatically entered to page: F, on the adjustment remote commander. address: CA, CB.) 8) Set data: 0B to page: 2, address: 01, and press the PAUSE button 7) Confirm that the data on page: 2, address: 02 is “01”. on the adjustment remote commander. (The auto white balance reference data are entered, and they Processing after adjustment finished: are set automatically to page F, address: CC to CF.) 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button 9) Confirm that the data on page: 2, address: 02 is “01”. on the adjustment remote commander. 2) Set data: 00 to page: 2, address: 10, and press the PAUSE button Processing after adjustment finished: on the adjustment remote commander. 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. 2) Set data: 15 to page: E, address: 11, and press the PAUSE button on the adjustment remote commander. 3) Set data: 00 to page: 2, address: 10, and press the PAUSE button on the adjustment remote commander. 4) Set data: 00 to page: 0, address: 01. 5) Perform “Auto white balance adjustment”. 5-15, 9. Auto white balance adjustment 10. White balance check This adjustment corrects the output data of auto white balance. If Clear chart disordered, the colors will not be reproduced correctly in the auto Subject (Shoot with color bar standard picture white balance mode. frame) Clear chart Filter ND filter 1.0 and 0.3 Subject (Shoot with color bar standard picture Check DDS display on LCD screen frame) Measurement point (Note 1, 2) Color temperature compensating filter Filter When data:0F is set to page: 2, C14 address: 01 Measurement point Check DDS display on LCD screen (Note 1) Measuring equipment (Note 2) R-Y: 00 to 04 or FC to FF Adjustment page F Specification value B-Y: 00 to 04 or FC to FF When data: 00 is set to page: 0, Adjustment address D3, D4 address: 00 R ratio: 2B40 to 2BC0 Specification value (Note 2) B ratio: 5E40 to 5EC0 0E10 or more Note 1: “Auto white balance reference data input” must be already Note 1: Right side 4 digits of data displayed at the lower right of finished. LCD screen. Note 2: Right side 2 digits of data displayed at the lower right of 00 XX XX LCD screen. R-Y 00 00 XX B-Y Displayed data Note 2: Data displayed at the lower right of LCD screen. 00 XX XX Adjustment procedure: Displayed data 1) Put the color temperature compensating filter C14 on the lens. 2) Set data: 01 to page: 0, address: 01. Adjustment procedure: 3) Set data: 58 to page: 2, address: 10, and press the PAUSE button 1) Set data: 01 to page: 0, address: 01. on the adjustment remote commander. 2) Set data: 58 to page: 2, address: 10, and press the PAUSE button 4) Turn off the HOLD switch on the adjustment remote on the adjustment remote commander. commander. 3) Turn off the HOLD switch on the adjustment remote 5) After more than 2 seconds, turn on the the HOLD switch on commander. the adjustment remote commander. 4) After more than 2 seconds, turn on the the HOLD switch on 6) Set data: 0A to page: E, address: 11, and press the PAUSE the adjustment remote commander. button on the adjustment remote commander. 5) Set data: 15 to page: E, address: 11, and press the PAUSE button 7) Set data: 3F to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. on the adjustment remote commander. 6) Set data: 02 to page: 0, address: 03. 8) Set data: 04 to page: 0, address: 03. 7) Set data: 56 to page: 2, address: 56, and press the PAUSE button 9) Change the data on page: F, address: D3 so that average value on the adjustment remote commander. of DDS displayed data (Note 2) satisfies the R ratio specification 8) Set data: 0F to page: 2, address: 01, and press the PAUSE button value. on the adjustment remote commander. 10) Press the PAUSE button on the adjustment remote commander. 9) Confirm that the DDS displayed data (Note 1) is in a range of 11) Set data: 05 to page: 0, address: 03. “00 to 04” or “FC to FF”. 12) Change the data on page: F, address: D4 so that average value 10) Set data: 00 to page: 0, address: 00. of DDS displayed data satisfies the B ratio specification value. 11) Confirm that the DDS displayed data (Note 2) is more than 13) Press the PAUSE button on the adjustment remote commander. “E10”. 12) Put the ND filter 1.3 (1.0 + 0.3) on the lens. Processing after adjustment finished: 13) Confirm that the DDS displayed data (Note 2) is lessthan “D0”. 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button on the adjustment remote commander. Processing after adjustment finished: 2) Set data: 00 to page: 0, address: 03. 1) Set data: 00 to page: 2, address: 01, and press the PAUSE button 3) Set data: 00 to page: 2, address: 10, and press the PAUSE button on the adjustment remote commander. on the adjustment remote commander. 2) Set data: 00 to page: 2, address: 56, and press the PAUSE button 4) Set data: 15 to page: E, address: 11, and press the PAUSE button on the adjustment remote commander. on the adjustment remote commander. 3) Set data: 00 to page: 2, address: 10, and press the PAUSE button 5) Set data: 00 to page: 0, address: 01. on the adjustment remote commander. 4) Set data: 00 to page: 0, address: 01. 5-16, 11. Hue gain adjustment [Reference] Adjust the color separetion matrix coefficient so that proper color This illustration shows the color changes on vector scope display reproduction is produced. when address: 23 to 2A are changed. Subject Color bar chart standard picture frame Adjustment Page E Burst position R-Y Adjustment Address 23 to 2A R MG Shoot the color bar chart and save it on a FD. Play back the recorded FD and Specification Value compare it on a PC display with the color bar playback of the alignment FD. YL PC: Personal computer B-Y FD: Floppy disk B Note 1: Auto white balance reference data input and Auto white balance adjustment must be already set. G

CY

Adjustment procedure: 1) Set data: 01 to page: 0, address: 01. Fig. 5-1-11 2) Set data: 0A to page: E, address: 11, and press the PAUSE button on the adjustment remote commander. 3) Set data: 0F to page: 2, address: 01, and press the PAUSE button Processing after adjustment finished: on the adjustment remote commander. 1) Set data: 15 to page: E, address: 11, and press the PAUSE button 4) Set data: 59 to page: 2, address: 10, and press the PAUSE button on the adjustment remote commander. on the adjustment remote commander. 2) Set data: 00 to page: 2, address: 01, and press the PAUSE button 5) Turn off the HOLD switch on the adjustment remote on the adjustment remote commander. commander. 3) Set data: 00 to page: 2, address: 10, and press the PAUSE button 6) After more than 2 seconds, turn on the the HOLD switch on on the adjustment remote commander. the adjustment remote commander. 4) Set data: 00 to page: 0, address: 01. 7) Change the data of page: E, address: 23 to 2A, and compare the colors. If you find color differences, adjust the following data slightly and press the PAUSE button on the adjustment remote commander. Note 2: We recommend you to take note the red and yellow data before starting adjustment. 5-17, 1-4. LCD SYSTEM ADJUSTMENT Alignment disk (Disk-1, Disk-2) Note 1: A back light (fluorescent tube) is driven with high voltage (A set of alignment disks consists of two disks as a pair.) AC power. Therefore, do not touch the back light directly, Disk-1: 8-967-990-01 otherwise you will feel an electric shock. (TFD2-1 (+)) (+17.5 µm) Note 2: Take an extreme care not to destroy the LCD unit by static Disk-2: 8-967-990-11 electricity when replacing it. (TFD2-2 (–)) (–17.5 µm) [Connector for adjustment] [Common signals in the disks] The measurement points for LCD adjustment are located almost at Data Code Signal the CN802 on the PK-43 board. MVC-001C.JPG Color bars Connect the measuring equipment via CPC-9 jig (J-6082-393-B). The pin No. and signal name of CN802 are listed below. MVC-002M.JPG Monoscope Pin No. Signal Name Pin No. Signal Name MVC-003V.JPG V. COM adjustment signal MVC-004W.JPG 100% white 1 PANEL B 10 UNREG MVC-005H.JPG 50% white 2 PANEL G 11 LANC IN MVC-006T.JPG Stair-step signal of 10 steps 3 PANEL R 12 LANC OUT MVC-007R.JPG Red single color 4 REG GND 13 XPWR SW MVC-008G.JPG Green single color 5 JIG XHD 14 MAKER RECOG MVC-009B.JPG Blue single color 6 JIG XVD 15 INDEX MVC-010D.JPG Camera color bars 7 HSY 16 TRACK 00 MVC-011N.JPG Camera monoscope 8 COM 17 NC • Contents of alignment disk-1 9 VG 18 FDD RF (Common signal) + (+17.5 µm alignment) • Contents of alignment disk-2 [LCD type judging method] (Common signal) + (–17.5 µm alignment) The LCD type can be judged by measuring resistance between 4 pin and !¢ pin of CPC-9 jig. Resistance LCD Type 10 kΩ SHARP0ΩCASIO Digital voltmeter CPC-9 (J-608-393-B) !¢pin 4pin Fig. 5-1-12 5-18, 1. Power supply voltage check (FC-66 board) 3. VCO adjustment (PK-43 board) Mode Camera record Set the VCO free run frequency. If disordered, LCD screen will be faulty. Subject Any subject Mode Stop Measuring Equipment Digital voltmeter Signal None PANEL 4.9 V check Measurement point PK-43 board CN802 7 pin (HSY) Measuring Point CN602 pin 5 Measuring equipment Frequency counter Specification Value 4.9 ± 0.1 Vdc Adjustment page F PANEL 3.2 V check Adjustment address 36 Measuring Point CN602 pin 7 Specification value 15734 ± 30 Hz Specification Value 3.20 ± 0.1 Vdc PANEL 6.5 V check Adjustment procedure: Measuring Point CN602 pin 9 1) Set data: 01 to page: 0, address: 01. Specification Value 6.5 ± 0.4 Vdc 2) Set data: 20 to page: 3, address: 18, and press the PAUSE button on the adjustment remote commander. PANEL 13.2 V check 3) Change the data on page: F, address: 36 so that the HSY signal Measuring Point CN602 pin 6 frequency satisfies the specification value. Specification Value 13.2 ± 0.4 Vdc 4) Press the PAUSE button on the adjustment remote commander. PANEL –15.3 V check Processing after adjustment finished: Measuring Point CN602 pin 8 1) Set data: 00 to page: 3, address: 18, and press the PAUSE button Specification Value –15.3 ± 0.4 Vdc on the adjustment remote commander. 2) Set data: 00 to page: 0, address: 01. 2. EVR initial data input Mode Playback Signal Any Adjustment page F Adjustment address 30, 33 to 39, 3B Adjustment procedure: 1) Set data: 01 to page: 0, address: 01. 2) Select page: F, and enter the data given in the following table. Note: Press the PAUSE button on the adjustment remote commander each time the data are set, as the data are written to nonvolatile memory (EEPROM). Address Data Remarks SHARP CASIO 30 BC BB BRIGHT adjustment 33 B9 77 White balance adjustment 34 B7 7A White balance adjustment 35 BE DB CONTRAST adjustment 36 61 73 VCO adjustment 37 74 97 V-COM adjustment 38 C8 78 D RANGE adjustment 39 7C 36 V-COM level adjustment 3B 72 5E Fixed value Processing after adjustment finished: 1) Set data: 00 to page: 0, address: 01. 5-19, 4. D RANGE adjustment (PK-43 board) 5. BRIGHT adjustment (PK-43 board) This adjustment sets correctly the D range of LCD driver. This adjustment sets correctly the VIDEO signal level that drives If disordered, LCD screen will blur or white blur. the LCD. If disordered, LCD screen will not be sharp, or will white Mode Playback blur or black blur. Signal Alignment disk: Stair-step signal of 10 Mode Playback steps Alignment disk: Stair-step signal of 10 Signal CN802 9 pin (VG) steps Measurement point External trigger: CN802 7 pin (HSY) CN802 9 pin (VG) Measurement point Measuring equipment Oscilloscope External trigger: CN802 7 pin (HSY) Adjustment page F Measuring equipment Oscilloscope Adjustment address 38 Adjustment page F A=3.99 ± 0.05 Vp-p (SHARP) Adjustment address 30 Specification value A=3.12 ± 0.05 Vp-p (CASIO) A=1.78 ± 0.05 Vp-p (SHARP) Specification value A=1.43 ± 0.05 Vp-p (CASIO) Adjustment procedure: 1) Set data: 01 to page: 0, address: 01. Adjustment procedure: 2) Change the data on page: F, address: 38 so that the voltage (A) 1) Set data: 01 to page: 0, address: 01. between pedestal of inverted waveform and pedestal of 2) Set data: 08 to page: 3, address: 18, and press the PAUSE button noninverted waveform satisfies the specification value. on the adjustment remote commander. 3) Press the PAUSE button on the adjustment remote commander. 3) Change the data on page: F, address: 30 so that the voltage (A) satisfies the specification value. (Confirm that the data at Processing after adjustment finished: address: 30 is more than “41”, and less than “BF”.) 1) Set data: 00 to page: 0, address: 01. 4) Press the PAUSE button on the adjustment remote commander. Processing after adjustment finished: 0 IRE 1) Set data: 00 to page: 3, address: 18, and press the PAUSE button on the adjustment remote commander. 2) Set data: 00 to page: 0, address: 01.

A

0 IRE 2H A: Pedestal level difference between 1H period and A previous 1H period. 0 IRE Fig. 5-1-13 2H Fig. 5-1-14 5-20, 6. CONTRAST adjustment (PK-43 board) 7. V-COM level adjustment (PK-43 board) This adjustment sets correctly the VIDEO signal level that drives This adjustment sets correctly the common electrode drive signal the LCD. If disordered, LCD screen will not be sharp, or will white level of the LCD panel. blur or black blur. Mode Playback Mode Playback Alignment disk: Stair-step signal of Signal Alignment disk: Stair-step signal of 10 10 steps Signal steps Measurement point CN802 8 pin (COM) CN802 9 pin (VG) Measurement point Measuring equipment Oscilloscope External trigger: CN802 7 pin (HSY) Adjustment page F Measuring equipment Oscilloscope Adjustment address 39 Adjustment page F A=6.50 ± 0.05 Vp-p (SHARP) Adjustment address 35 Specification value A=5.10 ± 0.05 Vp-p (CASIO) A=2.90 ± 0.07 Vp-p (SHARP) Specification value A=2.18 ± 0.07 Vp-p (CASIO) Note: The “CONTRAST adjustment” and “BRIGHT adjustment” must be already finished. Adjustment procedure: 1) Set data: 01 to page: 0, address: 01. Adjustment procedure: 2) Change the data on page: F, address: 35 so that the voltage (A) 1) Set data: 01 to page: 0, address: 01. between pedestal (0IRE) and 100IRE satisfies the specification 2) Change the data on page: F, address: 39 so that the COM signal value. level (A) satisfies the specification value. 3) Press the PAUSE button on the adjustment remote commander. 3) Press the PAUSE button on the adjustment remote commander. Processing after adjustment finished: Processing after adjustment finished: 1) Set data: 00 to page: 0, address: 01. 1) Set data: 00 to page: 0, address: 01. 2) Confirm that the specification value of the “BRIGHT adjustment” is satisfied. If not, perform the “BRIGHT adjustment”.

A

100 IRE 2H

A

Fig. 5-1-16 0 IRE 2H Fig. 5-1-15 5-21, 8. V-COM adjustment (PK-43 board) 9. White balance adjustment (PK-43 board) This adjustment corrects the DC bias of common electrode drive This adjustment corrects the white balance. signals of the LCD panel. If shifted, the LCD screen will be coarse, If disordered, the colors on LCD screen will not be reproduced or flicker, or vertical streaks will appear. correctly. Mode Playback Mode Playback Signal No signal Alignment disk: 50% white signal Signal Measurement point (with burst) Check on LCD screen Measuring equipment Measurement point Check on LCD screen Adjustment page F Measuring equipment Adjustment address 37 Adjustment page F The brightness difference between the Adjustment address 33, 34 Specification value section A and section B is minimum. Specification value LCD screen must not be colored. Note: The “CONTRAST adjustment” and “BRIGHT adjustment” Note: Check the white balance only when either of the following must be already finished. parts was replaced, and make adjustment only if necessary. 1. LCD panel Adjustment procedure: 2. IC802 1) Set data: 01 to page: 0, address: 01. 2) Set data: 10 to page: 3, address: 18 and press the PAUSE button Adjustment procedure: on the adjustment remote commander. 1) Set data: 01 to page: 0, address: 01. 3) Change the data on page: F, address: 37 so that the brightness 2) Change the data on page:F, address: 33, 34 so that the LCD at part A and part B is equal. screen is not colored. 4) Press the PAUSE button on the adjustment remote commander. 3) Press the PAUSE button on the adjustment remote commander. Processing after adjustment finished: Processing after adjustment finished: 1) Set data: 00 to page: 3, address: 18 and press the PAUSE button 1) Set data: 00 to page: 0, address: 01. on the adjustment remote commander. 2) Set data: 00 to page: 0, address: 01. BAABBAABFig. 5-1-17 5-22, 1-5. SYSTEM CONTROL ADJUSTMENT Adjustment procedure: 1. Battery down adjustment (FC-66 board) 1) Connect the adjustment remote commaner (RM-95) via CPC- This adjustment specifies the battery end voltage. If disordered, the 9 jig. battery service life will be shortened, or images will be deformed at 2) Adjust the output voltage of regulated power supply so that the the battery end. digital voltmeter indicates 6.1 ± 0.1 Vdc. Mode Camera record Note1: Change over the HOLD switch on the adjustment remote commander to the ADJ position immediately after the Signal Any DC power was supplied. LCD screen on the adjustment remote Measurement point 3) Insert a floppy disk (already formatted), and select the Measuring equipment commander CAMERA RECORD mode. Adjustment page F 4) Set data: 01 to page: 0, address: 01. Adjustment address 18 to 1C 5) Adjust the output voltage of regulated power supply so that the digital voltmeter indicates 5.80 ± 0.01 Vdc. Switch setting: 6) Read the displayed data (Dref) on page: 3, address: 0D. 1) AUTO FOCUS/MANUAL ... MANUAL 7) Set the read data (Dref) to page: F, address: 18, and press the PAUSE button on the adjustment remote commander. Connection: 8) Convert Dref into decimal number to get Dref’. 1) Connect the regulated power supply and a digital voltmeter as (See Table 5-1-1. Hexadecimal-Decimal Conversion table) shown in Fig. 5-1-18. 9) Calculate the adjustment data (decimal numbers) with the following formulas (calculate decimal numbers), and convert them into hexadecimal numbers, then set them to respective Digital voltmeter adjustment addresses. Address: 19 D19'=Dref’+8 Address: 1A D1A’=Dref’+23 Address: 1B D1B’=Dref’+44 + Address: 1C D1C’=Dref’+55 – Note2: Be sure to press the PAUSE button on the adjustment remote commander after setting each data. Regulated power supply 10) Set data: 00 to page: 0, address: 01. 2. Battery down check + Connection: 1) Connect same as “battery down adjustment”. – – + ± Adjustment procedure:(6.10 0.1 Vdc) 1) Adjust the output voltage of the regulated power supply so that the digital voltmeter indicates 6.10 ± 0.1 Vdc. Battery terminal 2) Insert a floppy disk and enter the camera recording mode. (CAM REC) 3) Adjust the output voltage of regulated power supply so that the digital voltmeter indicates 6.08 ± 0.01 Vdc. Fig. 5-1-18 4) Confirm that a battery mark on the LCD screen blinks at 0.8 Hz. 5) Adjust the output voltage of regulated power supply so that the digital voltmeter indicates 5.77 ± 0.01 Vdc. 6) Confirm that a battery mark on the LCD screen blinks at 3.2 Hz, then the power is turned off. 5-23E,

MVC-FD71 SECTION 6 REPAIR PARTS LIST

6-1. EXPLODED VIEWS Note: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark ! or have some differences from the original one. in the exploded views are not supplied. dotted line with mark ! are critical for safety. • Items marked “*” are not stocked since they Replace only with part number specified. are seldom required for routine service. Some Les composants identifiés par une marque delay should be anticipated when ordering these ! sont critiques pour la sécurité. items. Ne les remplacer que par une pièce portant le numéro spécifié. 6-1-1. CABINET (FRONT) SECTION 11 15 not supplied 6 15 5 16 4 not 7 supplied48not not 9 15 supplied supplied not supplied 13 1534210 1 15 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1 X-3948-761-1 CABINET (FRONT) ASSY 9 3-051-435-01 SCREW (M1.7) 2 X-3948-906-1 RING ASSY, LENS 10 3-050-468-01 SCREW, TRIPOD 3 3-977-651-11 CLAW, BT LOCK 11 1-694-297-11 TERMINAL BOARD, BATTERY 4 3-948-339-61 TAPPING 12 A-7073-591-A RL-50 BOARD, COMPLETE 5 3-969-380-01 SPRING, BATTERY !13 1-475-832-11 FLASH UNIT 6 3-736-363-31 TAPPING 14 1-475-842-11 MF BLOCK 7 X-3948-763-1 SHAFT ASSY, BATTERY 15 3-968-729-01 SCREW (M2), LOCK ACE, P2 * 8 3-977-653-01 SPRING, COMPRESSION 16 1-958-849-11 HARNESS (FF-188) 17 X-3948-918-1 LID ASSY, BATTERY 6-1, 6-1-2. CABINET (REAR) SECTION 57 58 (Note) 60 61 59 52 53 66 LCD901 59 52 64 73 59 63 52 69 67 59 70 68 74 52 Lens block ass'y51 59 (See page 6-3.) ND801 59 71 (Note) The FD block assembly is a mechanical unit which has completely been adjusted in the factory. So never disassemble the FD block assembly. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 51 A-7093-879-A FC-66 BOARD, COMPLETE (SERVICE) 65 3-050-501-01 LEVER, EJECT 52 3-713-786-21 SCREW (M2X3) 66 3-050-504-01 SPRING, LEVER 53 3-352-483-01 SCREW (M2), STEP 67 3-050-488-01 LID, LITHIUM 54 X-3948-765-1 FRAME ASSY, MAIN 68 1-670-486-21 FP-35 FLEXIBLE BOARD 55 3-050-457-01 LID, SIDE 69 3-978-439-01 BUTTON, CONTROL 56 3-050-458-01 SPRING (UPPER), SIDE * 70 3-979-292-01 SHEET (CONTROL) 57 1-759-679-11 DRIVE, FLOPPY DISK (3.5inch) (Note) 71 A-7093-880-A PK-43 (CASIO) BOARD, COMPLETE (SERVICE) 58 X-3948-762-1 CABINET (REAR) ASSY 71 A-7093-881-A PK-43 (SHARP) BOARD, COMPLETE 59 3-948-339-61 TAPPING (SERVICE) 60 3-050-456-01 CABINET, SIDE 72 3-050-441-01 PLATE, FD RELAY * 73 3-051-700-02 SHEET, BLIND 61 3-050-467-01 SHEET METAL (R), STRAP 62 3-050-500-01 KNOB, EJECT 74 3-050-489-01 COVER, CPC 63 3-050-906-01 BUTTON, EJECT LOCK LCD901 1-803-036-21 INDICATOR MODULE, LIQUID CRYSTAL 64 3-050-907-01 SPRING, EJECT LOCK (SHARP) LCD901 1-803-184-21 INDICATOR MODULE, LIQUID CRYSTAL (CASIO) !ND801 1-517-787-11 TUBE, FLUORESCENT, COLD CATHODE The components identified by Les composants identifiés par une mark ! or dotted line with marque ! sont critiques pour la mark ! are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-2 ber specified. portant le numéro spécifié., 6-1-3. LENS BLOCK ASS'Y SECTION 102 IC401 109 105 106 M902 (Note) 101 M901 (Note) M1.7X5 M1.7X5 * Be sure to read “Precautions for Replacement of CCD Imager” on page 4-6 when changing the CCD imager. (Note) Flexible board of zoom lens is not supplied. Please be careful not to break the flexible board when you change the motor unit. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 101 1-758-177-11 LENS, ZOOM (VCL-4210VD) 107 3-953-817-01 RUBBER (F), SEAL 102 1-670-487-11 FP-34 FLEXIBLE BOARD 108 A-7073-589-A CD-196 BOARD, COMPLETE 103 3-318-382-21 SCREW (1.7X3), TAPPING 109 3-318-203-11 SCREW (B1.7X6), TAPPING * 104 3-050-439-01 FRAME, LENS IC401 A-7030-901-A CCD BLOCK ASSY 105 3-953-816-01 ADAPTOR (F), CCD FITTING M901 3-709-404-01 MOTOR UNIT, FOCUS (Note) 106 1-758-204-11 FILTER BLOCK, OPTICAL M902 3-709-403-01 MOTOR UNIT, ZOOM (Note) 6-3,

CD-196 FC-66

6-2. ELECTRICAL PARTS LIST Note: When indicating parts by reference number, • Due to standardization, replacements in the • RESISTORS please include the board naame. parts list may be different from the parts All resistors are in ohms. specified in the diagrams or the components METAL: metal-film resistor The components identified by mark ! or used on the set. METAL OXIDE: Metal Oxide-film resistor dotted line with mark ! are critical for safety. • -XX, -X mean standardized parts, so they may F: nonflammable Replace only with part number specified. have some difference from the original one. • COILS Les composants identifiés par une marque • Items marked “*” are not stocked since they uH: µH ! sont critiques pour la sécurité. Ne les remplacer que par une pièce portant are seldom required for routine service. Some • SEMICONDUCTORS le numéro spécifié. delay should be anticipated when ordering these In each case, u: µ, for example: items. uA...: µA... , uPA... , µPA... , • CAPACITORS: uPB... , µPB... , uPC... , µPC... , uF: µF uPD..., µPD... Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7073-589-A CD-196 BOARD, COMPLETE C124 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V ********************** C125 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (Ref.No.:2,000 Series) C126 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C127 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < CAPACITOR > C128 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V C401 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C129 1-164-346-11 CERAMIC CHIP 1uF 16V C403 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C130 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V C404 1-135-214-21 TANTAL. CHIP 4.7uF 20% 20V C131 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C405 1-135-210-11 TANTALUM CHIP 4.7uF 20% 10V C132 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < CONNECTOR > C133 1-162-923-11 CERAMIC CHIP 47PF 5% 50V C134 1-162-923-11 CERAMIC CHIP 47PF 5% 50V CN401 1-766-346-21 CONNECTOR, FFC/FPC 16P C135 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V C302 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < COIL > C303 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V L401 1-414-757-11 INDUCTOR 100uH C401 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C402 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V < TRANSISTOR > C403 1-109-982-11 CERAMIC CHIP 1uF 10% 10V C404 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q401 8-729-117-73 TRANSISTOR 2SC4178-F13F14-T1 C405 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < RESISTOR > C406 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C407 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R401 1-216-827-11 METAL CHIP 3.3K 5% 1/16W C408 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V R402 1-216-809-11 METAL CHIP 100 5% 1/16W C409 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R403 1-216-809-11 METAL CHIP 100 5% 1/16W C410 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C411 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V A-7093-879-A FC-66 BOARD, COMPLETE (SERVICE) C412 1-104-752-11 TANTAL. CHIP 33uF 20% 6.3V ****************************** C413 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V (Ref.No.:1,000 Series) C415 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C416 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < CAPACITOR > C417 1-164-346-11 CERAMIC CHIP 1uF 16V C103 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C418 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C104 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V C419 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C107 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C420 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V C108 1-135-214-21 TANTAL. CHIP 4.7uF 20% 20V C421 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C109 1-115-156-11 CERAMIC CHIP 1uF 10V C501 1-104-852-11 TANTAL. CHIP 22uF 20% 10V C110 1-163-021-91 CERAMIC CHIP 0.01uF 10% 50V C502 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C111 1-162-974-11 CERAMIC CHIP 0.01uF 50V C503 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C112 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C504 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C113 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C601 1-135-181-21 TANTALUM CHIP 4.7uF 20% 6.3V C114 1-162-909-11 CERAMIC CHIP 4PF 0.25PF 50V C602 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C116 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C603 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C117 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C604 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C119 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C605 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C120 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C606 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C121 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C607 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C122 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C608 1-107-682-11 CERAMIC CHIP 1uF 10% 16V 6-4,

FC-66

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C611 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C925 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C701 1-115-156-11 CERAMIC CHIP 1uF 10V C702 1-115-156-11 CERAMIC CHIP 1uF 10V C926 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C927 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C703 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C928 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C704 1-104-847-11 TANTAL. CHIP 22uF 20% 4V C929 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C706 1-104-847-11 TANTAL. CHIP 22uF 20% 4V C707 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C930 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C708 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C931 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C932 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C709 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C933 1-115-566-11 CERAMIC CHIP 4.7uF 10% 10V C713 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C934 1-135-216-11 TANTALUM CHIP 10uF 20% 10V C714 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C715 1-162-919-11 CERAMIC CHIP 22PF 5% 50V C935 1-135-216-11 TANTALUM CHIP 10uF 20% 10V C716 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C936 1-135-216-11 TANTALUM CHIP 10uF 20% 10V C937 1-164-506-11 CERAMIC CHIP 4.7uF 16V C717 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C938 1-164-506-11 CERAMIC CHIP 4.7uF 16V C718 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C939 1-164-506-11 CERAMIC CHIP 4.7uF 16V C720 1-115-156-11 CERAMIC CHIP 1uF 10V C724 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C940 1-135-214-21 TANTAL. CHIP 4.7uF 20% 20V C725 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C942 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C943 1-135-216-11 TANTALUM CHIP 10uF 20% 10V C726 1-135-091-00 TANTALUM CHIP 1uF 20% 16V C944 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C727 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C945 1-165-319-11 CERAMIC CHIP 0.1uF 50V C804 1-110-563-11 CERAMIC CHIP 0.068uF 10% 16V C805 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C946 1-165-319-11 CERAMIC CHIP 0.1uF 50V C806 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C947 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C948 1-135-179-21 TANTAL. CHIP 2.2uF 20% 16V C807 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C949 1-164-506-11 CERAMIC CHIP 4.7uF 16V C808 1-162-969-11 CERAMIC CHIP 0.0068uF 10% 25V C950 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C809 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C810 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C951 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C811 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V < CONNECTOR > C812 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V C813 1-162-919-11 CERAMIC CHIP 22PF 5% 50V CN101 1-779-332-11 CONNECTOR, FFC/FPC 16P C814 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10V CN401 1-779-334-11 CONNECTOR, FFC/FPC 20P C815 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN602 1-778-084-11 CONNECTOR, BOARD TO BOARD 60P C818 1-164-315-11 CERAMIC CHIP 470PF 5% 50V CN901 1-580-057-11 PIN, CONNECTOR 4P CN907 1-770-620-21 PIN, CONNECTOR 3P C819 1-109-982-11 CERAMIC CHIP 1uF 10% 10V C820 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN910 1-770-630-21 PIN, CONNECTOR 13P C821 1-119-750-11 TANTAL. CHIP 22uF 20% 6.3V C822 1-109-982-11 CERAMIC CHIP 1uF 10% 10V < DIODE > C823 1-109-982-11 CERAMIC CHIP 1uF 10% 10V D701 8-719-049-09 DIODE 1SS367-T3SONY C824 1-109-982-11 CERAMIC CHIP 1uF 10% 10V D702 8-719-404-49 DIODE MA111-TX C825 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D703 8-719-049-09 DIODE 1SS367-T3SONY C902 1-164-218-11 CERAMIC CHIP 180PF 0.25PF 50V D706 8-719-061-82 DIODE TLSU1002(TPX1,SONY) (SELF TIMER) C903 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D904 8-719-027-76 DIODE 1SS357-TPH3 C904 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D905 8-719-027-77 DIODE MA796-TX C905 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V D906 8-719-404-49 DIODE MA111-TX C906 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D907 8-719-404-49 DIODE MA111-TX C908 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V C909 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V < FUSE > C910 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V !F901 1-533-709-11 FUSE (SMD) (1.25A) C914 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V !F902 1-533-709-11 FUSE (SMD) (1.25A) C915 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V !F903 1-533-709-11 FUSE (SMD) (1.25A) C916 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V !F904 1-533-709-11 FUSE (SMD) (1.25A) C918 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C919 1-162-962-11 CERAMIC CHIP 470PF 10% 50V < FERRITE BEAD > C920 1-104-913-11 TANTAL. CHIP 10uF 20% 16V FB101 1-500-283-11 INDUCTOR CHIP 0UH C921 1-104-913-11 TANTAL. CHIP 10uF 20% 16V FB102 1-414-228-11 INDUCTOR CHIP 0UH C922 1-162-962-11 CERAMIC CHIP 470PF 10% 50V FB103 1-500-284-21 INDUCTOR CHIP 0UH C923 1-162-962-11 CERAMIC CHIP 470PF 10% 50V FB104 1-414-228-11 INDUCTOR CHIP 0UH C924 1-104-913-11 TANTAL. CHIP 10uF 20% 16V The components identified by Les composants identifiés par une mark ! or dotted line with marque ! sont critiques pour la mark ! are critical for safety. sécurité. Replace only with part num- Ne les remplacer que par une pièce 6-5 ber specified. portant le numéro spécifié.,

FC-66

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > Q401 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO IC102 8-759-526-24 IC CCD1000Y/T2 Q402 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC103 8-752-391-91 IC CXD2450R-T4 Q403 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC104 8-752-394-75 IC CXD3137R-T6 Q601 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC301 8-759-364-05 IC M62376GP-65AD Q602 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC401 8-759-337-40 IC NJM2904V(TE2) Q603 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC402 8-759-365-18 IC uPD16833G3-E2 Q701 8-729-024-48 TRANSISTOR 2SK1830-TE85L IC403 8-752-377-38 IC CXD2430N-T4 Q702 8-729-032-62 TRANSISTOR 2SJ347-TE85L IC404 8-759-338-78 IC BA10324AFV-E2 Q703 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC405 8-759-075-66 IC TA75S01F(TE85R) Q704 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC501 8-759-543-83 IC KM416V1204CT-L6 Q706 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC501 8-759-543-84 IC MSM51V18165BSL-60TS-K Q707 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC501 8-759-546-82 IC uPD42S18165LG5-A60-7JF-E2 Q708 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC503 8-752-393-45 IC CXD3136R-T6 Q801 8-729-037-61 TRANSISTOR UN9113J-(K8).SO IC601 8-752-384-33 IC CXD3121R-T4 Q802 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC701 8-759-298-10 IC S-8423NFS-T2 Q803 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC702 8-759-561-82 IC S579284PZ-TEB Q906 8-729-033-14 TRANSISTOR FP107-TL IC703 8-759-445-94 IC AK6480AM-E2 Q907 8-729-804-41 TRANSISTOR 2SB1122-ST-TD IC705 8-759-535-20 IC MB90097PFV-G-109-BND-ER Q908 8-729-033-14 TRANSISTOR FP107-TL IC801 8-759-458-76 IC uPD72069GF-3BA Q909 8-729-033-14 TRANSISTOR FP107-TL IC802 8-759-196-97 IC TC7SH32FU-TE85R Q910 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC803 8-759-466-32 IC TA8563FN(EL) Q911 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC804 8-759-475-48 IC TC74LCX245FT(EL) Q912 8-729-015-60 TRANSISTOR 2SJ316-TD IC805 8-759-083-94 IC TC7W74FU(TE12R) Q913 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC806 8-759-557-74 IC HD6437410-SGX50070-MP2 Q914 8-729-037-61 TRANSISTOR UN9113J-(K8).SO IC807 8-759-553-13 IC MBM29LV200B-10PFTN-FK-ER Q915 8-729-037-74 TRANSISTOR UN9213J-(K8).SO IC807 8-759-553-14 IC MBM29LV200B-12PFTN-FK-ER Q916 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO IC901 8-759-060-94 IC MB3785APFV-G-BND-ER Q917 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q918 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO < COIL > Q919 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q920 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO L101 1-414-754-11 INDUCTOR 10uH L102 1-412-951-11 INDUCTOR 10uH Q921 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO L301 1-412-951-11 INDUCTOR 10uH Q922 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO L401 1-414-078-11 INDUCTOR 10uH Q923 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO L403 1-414-078-11 INDUCTOR 10uH Q924 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO Q925 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO L404 1-414-754-11 INDUCTOR 10uH L501 1-412-951-11 INDUCTOR 10uH Q926 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO L601 1-412-951-11 INDUCTOR 10uH Q927 8-729-037-53 TRANSISTOR 2SB1462J-QR(K8).SO L701 1-414-754-11 INDUCTOR 10uH Q928 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO L801 1-414-754-11 INDUCTOR 10uH Q929 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q930 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO L802 1-414-402-11 INDUCTOR 47uH L901 1-416-344-11 INDUCTOR 0uH < RESISTOR > L902 1-416-344-11 INDUCTOR 0uH L903 1-416-511-11 INDUCTOR 0uH R101 1-216-857-11 METAL CHIP 1M 5% 1/16W L904 1-416-345-11 INDUCTOR 0uH R102 1-216-845-11 METAL CHIP 100K 5% 1/16W R106 1-216-864-11 METAL CHIP 0 5% 1/16W L905 1-416-345-11 INDUCTOR 0uH R111 1-216-841-11 METAL CHIP 47K 5% 1/16W L906 1-412-056-11 INDUCTOR CHIP 4.7uH R112 1-216-833-11 METAL CHIP 10K 5% 1/16W L907 1-412-056-11 INDUCTOR CHIP 4.7uH L908 1-412-052-21 INDUCTOR CHIP 1uH R114 1-216-864-11 METAL CHIP 0 5% 1/16W L909 1-412-066-21 INDUCTOR CHIP 220uH R115 1-216-798-11 RES,CHIP 12 5% 1/16W R116 1-216-798-11 RES,CHIP 12 5% 1/16W L910 1-412-056-11 INDUCTOR CHIP 4.7uH R119 1-216-841-11 METAL CHIP 47K 5% 1/16W R121 1-216-808-11 METAL CHIP 82 5% 1/16W < TRANSISTOR > R401 1-216-841-11 METAL CHIP 47K 5% 1/16W Q101 8-729-037-61 TRANSISTOR UN9113J-(K8).SO R402 1-216-797-11 METAL CHIP 10 5% 1/16W Q102 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R403 1-216-829-11 METAL CHIP 4.7K 5% 1/16W Q103 8-729-037-61 TRANSISTOR UN9113J-(K8).SO R404 1-216-843-11 METAL CHIP 68K 5% 1/16W Q104 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R405 1-216-843-11 METAL CHIP 68K 5% 1/16W 6-6,

FC-66

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R406 1-216-821-11 METAL CHIP 1K 5% 1/16W R723 1-216-821-11 METAL CHIP 1K 5% 1/16W R407 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R724 1-216-821-11 METAL CHIP 1K 5% 1/16W R408 1-216-845-11 METAL CHIP 100K 5% 1/16W R409 1-216-833-11 METAL CHIP 10K 5% 1/16W R725 1-216-821-11 METAL CHIP 1K 5% 1/16W R410 1-216-845-11 METAL CHIP 100K 5% 1/16W R726 1-216-853-11 METAL CHIP 470K 5% 1/16W R727 1-216-833-11 METAL CHIP 10K 5% 1/16W R411 1-216-837-11 METAL CHIP 22K 5% 1/16W R728 1-216-833-11 METAL CHIP 10K 5% 1/16W R412 1-216-815-11 METAL CHIP 330 5% 1/16W R729 1-216-833-11 METAL CHIP 10K 5% 1/16W R413 1-216-837-11 METAL CHIP 22K 5% 1/16W R414 1-216-845-11 METAL CHIP 100K 5% 1/16W R730 1-216-821-11 METAL CHIP 1K 5% 1/16W R415 1-216-821-11 METAL CHIP 1K 5% 1/16W R736 1-216-841-11 METAL CHIP 47K 5% 1/16W R737 1-216-821-11 METAL CHIP 1K 5% 1/16W R416 1-216-837-11 METAL CHIP 22K 5% 1/16W R738 1-216-821-11 METAL CHIP 1K 5% 1/16W R417 1-216-848-11 METAL CHIP 180K 5% 1/16W R739 1-216-821-11 METAL CHIP 1K 5% 1/16W R418 1-216-833-11 METAL CHIP 10K 5% 1/16W R419 1-216-836-11 METAL CHIP 18K 5% 1/16W R740 1-216-821-11 METAL CHIP 1K 5% 1/16W R420 1-216-845-11 METAL CHIP 100K 5% 1/16W R741 1-216-853-11 METAL CHIP 470K 5% 1/16W R742 1-219-570-11 RES,CHIP 10M 5% 1/16W R422 1-216-848-11 METAL CHIP 180K 5% 1/16W R743 1-216-853-11 METAL CHIP 470K 5% 1/16W R423 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R744 1-216-864-11 METAL CHIP 0 5% 1/16W R424 1-216-851-11 METAL CHIP 330K 5% 1/16W R425 1-218-887-11 RES,CHIP 47K 0.50% 1/16W R745 1-216-849-11 METAL CHIP 220K 5% 1/16W R426 1-218-877-11 RES,CHIP 18K 0.50% 1/16W R746 1-216-845-11 METAL CHIP 100K 5% 1/16W R747 1-216-817-11 METAL CHIP 470 5% 1/16W R428 1-216-821-11 METAL CHIP 1K 5% 1/16W R749 1-216-853-11 METAL CHIP 470K 5% 1/16W R429 1-218-876-11 RES,CHIP 16K 0.50% 1/16W R751 1-216-845-11 METAL CHIP 100K 5% 1/16W R601 1-216-835-11 METAL CHIP 15K 5% 1/16W R605 1-216-835-11 METAL CHIP 15K 5% 1/16W R752 1-216-821-11 METAL CHIP 1K 5% 1/16W R606 1-216-835-11 METAL CHIP 15K 5% 1/16W R753 1-216-833-11 METAL CHIP 10K 5% 1/16W R757 1-216-864-11 METAL CHIP 0 5% 1/16W R610 1-216-821-11 METAL CHIP 1K 5% 1/16W R759 1-216-857-11 METAL CHIP 1M 5% 1/16W R611 1-216-840-11 METAL CHIP 39K 5% 1/16W R761 1-216-833-11 METAL CHIP 10K 5% 1/16W R612 1-216-834-11 METAL CHIP 12K 5% 1/16W R613 1-216-821-11 METAL CHIP 1K 5% 1/16W R762 1-216-821-11 METAL CHIP 1K 5% 1/16W R614 1-216-864-11 METAL CHIP 0 5% 1/16W R763 1-216-821-11 METAL CHIP 1K 5% 1/16W R764 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R615 1-216-821-11 METAL CHIP 1K 5% 1/16W R765 1-216-864-11 METAL CHIP 0 5% 1/16W R616 1-216-840-11 METAL CHIP 39K 5% 1/16W R769 1-216-845-11 METAL CHIP 100K 5% 1/16W R617 1-216-834-11 METAL CHIP 12K 5% 1/16W R618 1-216-821-11 METAL CHIP 1K 5% 1/16W R775 1-216-845-11 METAL CHIP 100K 5% 1/16W R619 1-216-864-11 METAL CHIP 0 5% 1/16W R776 1-216-857-11 METAL CHIP 1M 5% 1/16W R777 1-216-853-11 METAL CHIP 470K 5% 1/16W R620 1-216-821-11 METAL CHIP 1K 5% 1/16W R778 1-216-819-11 METAL CHIP 680 5% 1/16W R621 1-216-840-11 METAL CHIP 39K 5% 1/16W R779 1-216-845-11 METAL CHIP 100K 5% 1/16W R622 1-216-834-11 METAL CHIP 12K 5% 1/16W R623 1-216-821-11 METAL CHIP 1K 5% 1/16W R780 1-216-845-11 METAL CHIP 100K 5% 1/16W R624 1-216-864-11 METAL CHIP 0 5% 1/16W R802 1-216-864-11 METAL CHIP 0 5% 1/16W R804 1-216-864-11 METAL CHIP 0 5% 1/16W R701 1-216-845-11 METAL CHIP 100K 5% 1/16W R806 1-216-821-11 METAL CHIP 1K 5% 1/16W R702 1-216-813-11 METAL CHIP 220 5% 1/16W R807 1-216-827-11 METAL CHIP 3.3K 5% 1/16W R703 1-216-833-11 METAL CHIP 10K 5% 1/16W R704 1-216-853-11 METAL CHIP 470K 5% 1/16W R808 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R706 1-216-853-11 METAL CHIP 470K 5% 1/16W R809 1-218-878-11 RES,CHIP 20K 0.50% 1/16W R810 1-218-854-11 RES,CHIP 2K 0.50% 1/16W R707 1-216-845-11 METAL CHIP 100K 5% 1/16W R811 1-216-833-11 METAL CHIP 10K 5% 1/16W R708 1-216-845-11 METAL CHIP 100K 5% 1/16W R812 1-216-821-11 METAL CHIP 1K 5% 1/16W R709 1-216-845-11 METAL CHIP 100K 5% 1/16W R710 1-216-845-11 METAL CHIP 100K 5% 1/16W R813 1-216-821-11 METAL CHIP 1K 5% 1/16W R711 1-216-845-11 METAL CHIP 100K 5% 1/16W R814 1-216-821-11 METAL CHIP 1K 5% 1/16W R815 1-216-833-11 METAL CHIP 10K 5% 1/16W R712 1-216-853-11 METAL CHIP 470K 5% 1/16W R816 1-216-833-11 METAL CHIP 10K 5% 1/16W R713 1-216-853-11 METAL CHIP 470K 5% 1/16W R817 1-216-833-11 METAL CHIP 10K 5% 1/16W R714 1-216-853-11 METAL CHIP 470K 5% 1/16W R715 1-216-841-11 METAL CHIP 47K 5% 1/16W R818 1-216-833-11 METAL CHIP 10K 5% 1/16W R717 1-216-833-11 METAL CHIP 10K 5% 1/16W R819 1-216-833-11 METAL CHIP 10K 5% 1/16W R820 1-216-833-11 METAL CHIP 10K 5% 1/16W R718 1-216-853-11 METAL CHIP 470K 5% 1/16W R821 1-216-833-11 METAL CHIP 10K 5% 1/16W R721 1-216-821-11 METAL CHIP 1K 5% 1/16W R822 1-216-833-11 METAL CHIP 10K 5% 1/16W R722 1-216-821-11 METAL CHIP 1K 5% 1/16W 6-7,

FC-66

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R823 1-216-833-11 METAL CHIP 10K 5% 1/16W R940 1-216-864-11 METAL CHIP 0 5% 1/16W R825 1-216-833-11 METAL CHIP 10K 5% 1/16W R941 1-218-875-11 RES,CHIP 15K 0.50% 1/16W R826 1-216-853-11 METAL CHIP 470K 5% 1/16W R942 1-218-863-11 RES,CHIP 4.7K 0.50% 1/16W R827 1-216-841-11 METAL CHIP 47K 5% 1/16W R943 1-216-833-11 METAL CHIP 10K 5% 1/16W R828 1-216-833-11 METAL CHIP 10K 5% 1/16W R946 1-216-813-11 METAL CHIP 220 5% 1/16W R829 1-216-833-11 METAL CHIP 10K 5% 1/16W R947 1-216-819-11 METAL CHIP 680 5% 1/16W R830 1-216-833-11 METAL CHIP 10K 5% 1/16W R948 1-216-817-11 METAL CHIP 470 5% 1/16W R831 1-216-833-11 METAL CHIP 10K 5% 1/16W R949 1-216-817-11 METAL CHIP 470 5% 1/16W R832 1-216-835-11 METAL CHIP 15K 5% 1/16W R951 1-216-864-11 METAL CHIP 0 5% 1/16W R860 1-216-833-11 METAL CHIP 10K 5% 1/16W R952 1-216-845-11 METAL CHIP 100K 5% 1/16W R862 1-216-833-11 METAL CHIP 10K 5% 1/16W R953 1-216-845-11 METAL CHIP 100K 5% 1/16W R864 1-216-833-11 METAL CHIP 10K 5% 1/16W R954 1-216-821-11 METAL CHIP 1K 5% 1/16W R866 1-216-833-11 METAL CHIP 10K 5% 1/16W R956 1-216-845-11 METAL CHIP 100K 5% 1/16W R868 1-216-833-11 METAL CHIP 10K 5% 1/16W R957 1-216-841-11 METAL CHIP 47K 5% 1/16W R869 1-216-857-11 METAL CHIP 1M 5% 1/16W R958 1-216-837-11 METAL CHIP 22K 5% 1/16W R870 1-216-857-11 METAL CHIP 1M 5% 1/16W R959 1-216-864-11 METAL CHIP 0 5% 1/16W R871 1-216-833-11 METAL CHIP 10K 5% 1/16W R960 1-218-883-11 RES,CHIP 33K 0.50% 1/16W R872 1-216-833-11 METAL CHIP 10K 5% 1/16W R961 1-218-877-11 RES,CHIP 18K 0.50% 1/16W R873 1-216-841-11 METAL CHIP 47K 5% 1/16W R962 1-218-895-11 RES,CHIP 100K 0.50% 1/16W R874 1-216-841-11 METAL CHIP 47K 5% 1/16W R963 1-218-893-11 RES,CHIP 82K 0.50% 1/16W R875 1-216-841-11 METAL CHIP 47K 5% 1/16W R964 1-218-883-11 RES,CHIP 33K 0.50% 1/16W R876 1-216-841-11 METAL CHIP 47K 5% 1/16W R965 1-216-835-11 METAL CHIP 15K 5% 1/16W R877 1-216-841-11 METAL CHIP 47K 5% 1/16W R966 1-216-845-11 METAL CHIP 100K 5% 1/16W R878 1-216-841-11 METAL CHIP 47K 5% 1/16W R967 1-216-841-11 METAL CHIP 47K 5% 1/16W R879 1-216-841-11 METAL CHIP 47K 5% 1/16W R968 1-216-845-11 METAL CHIP 100K 5% 1/16W R880 1-216-841-11 METAL CHIP 47K 5% 1/16W R969 1-216-845-11 METAL CHIP 100K 5% 1/16W R904 1-216-864-11 METAL CHIP 0 5% 1/16W R970 1-216-845-11 METAL CHIP 100K 5% 1/16W R909 1-218-871-11 RES,CHIP 10K 0.50% 1/16W R971 1-216-841-11 METAL CHIP 47K 5% 1/16W R910 1-216-850-11 METAL CHIP 270K 5% 1/16W R972 1-216-845-11 METAL CHIP 100K 5% 1/16W R912 1-216-864-11 METAL CHIP 0 5% 1/16W R973 1-216-845-11 METAL CHIP 100K 5% 1/16W R913 1-216-864-11 METAL CHIP 0 5% 1/16W R974 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R914 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R975 1-216-833-11 METAL CHIP 10K 5% 1/16W R915 1-218-879-11 RES,CHIP 22K 0.50% 1/16W R976 1-218-877-11 RES,CHIP 18K 0.50% 1/16W R916 1-218-852-11 RES,CHIP 1.6K 0.50% 1/16W R977 1-218-852-11 RES,CHIP 1.6K 5% 1/16W R917 1-218-863-11 RES,CHIP 4.7K 0.50% 1/16W R978 1-218-897-11 RES,CHIP 120K 0.50% 1/16W R918 1-216-840-11 METAL CHIP 39K 5% 1/16W R979 1-218-882-11 RES,CHIP 30K 0.50% 1/16W R919 1-216-838-11 METAL CHIP 27K 5% 1/16W R980 1-218-871-11 RES,CHIP 10K 0.50% 1/16W R920 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R981 1-218-889-11 RES,CHIP 56K 0.50% 1/16W R921 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R983 1-216-295-91 SHORT 0 R922 1-216-864-11 METAL CHIP 0 5% 1/16W R984 1-216-295-91 SHORT 0 R924 1-218-871-11 RES,CHIP 10K 0.50% 1/16W R986 1-216-841-11 METAL CHIP 47K 5% 1/16W R925 1-218-837-11 RES,CHIP 390 0.50% 1/16W R926 1-218-871-11 RES,CHIP 10K 0.50% 1/16W < SHOCK SENSOR > R927 1-216-847-11 METAL CHIP 150K 5% 1/16W R928 1-216-833-11 METAL CHIP 10K 5% 1/16W SE801 1-801-868-41 SENSOR, SHOCK R929 1-216-864-11 METAL CHIP 0 5% 1/16W < TRANSFORMER > R930 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R931 1-218-871-11 RES,CHIP 10K 0.50% 1/16W !T901 1-429-565-21 TRANSFORMER, CONVERTER R932 1-216-864-11 METAL CHIP 0 5% 1/16W R933 1-218-871-11 RES,CHIP 10K 0.50% 1/16W < VIBRATOR > R934 1-216-841-11 METAL CHIP 47K 5% 1/16W X101 1-767-923-11 VIBRATOR, CRYSTAL (36MHz) R935 1-216-843-11 METAL CHIP 68K 5% 1/16W X701 1-767-450-11 VIBRATOR, CERAMIC (20MHz) R936 1-216-821-11 METAL CHIP 1K 5% 1/16W X702 1-760-458-21 VIBRATOR, CRYSTAL (32.768kHz) R937 1-216-821-11 METAL CHIP 1K 5% 1/16W X802 1-767-921-11 VIBRATOR, CERAMIC (15MHz) R938 1-216-864-11 METAL CHIP 0 5% 1/16W X803 1-767-922-11 VIBRATOR, CERAMIC (16MHz) Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une 6-8 specified. pièce portant le numéro spécifié.,

PK-43 (CASIO)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7093-880-A PK-43 (CASIO) BOARD, COMPLETE (SERVICE) C908 1-162-926-11 CERAMIC CHIP 82PF 5% 50V ************************************* C909 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V (Ref.No.;2,000 Series) C911 1-164-739-11 CERAMIC CHIP 560PF 5% 50V C913 1-162-926-11 CERAMIC CHIP 82PF 5% 50V < BATTERY HOLDER > C915 1-107-682-11 CERAMIC CHIP 1uF 10% 16V BH701 1-550-104-32 HOLDER, BATTERY C918 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C919 1-107-689-21 TANTAL. CHIP 1uF 20% 35V < BUZZER > C920 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C921 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V BZ701 1-529-107-11 BUZZER, PIEZOELECTRIC C925 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < CAPACITOR > C926 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C601 1-109-982-11 CERAMIC CHIP 1uF 10% 10V < CONNECTOR > C602 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C603 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V CN601 1-764-526-11 CONNECTOR, FFC/FPC 18P C604 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V * CN602 1-750-075-11 CONNECTOR, FFC/FPC 10P C605 1-113-642-11 TANTAL. CHIP 47uF 20% 10V CN603 1-778-598-21 CONNECTOR, BOARD TO BOARD 60P CN802 1-764-526-11 CONNECTOR, FFC/FPC 18P C606 1-113-642-11 TANTAL. CHIP 47uF 20% 10V CN851 1-573-929-11 CONNECTOR, FFC/FPC (ZIF) 20P C701 1-113-991-11 TANTAL. CHIP 33uF 20% 16V C702 1-107-682-11 CERAMIC CHIP 1uF 10% 16V CN901 1-691-388-11 CONNECTOR, FFC/FPC (ZIF) 24P C703 1-165-320-11 CERAMIC CHIP 0.47uF 10% 16V C801 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < DIODE > C802 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D701 8-719-061-82 DIODE TLSU1002(TPX1,SONY) (ACCESS) C803 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) C804 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V (FLASH CHARGE) C805 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D852 8-719-404-49 DIODE MA111-TX C806 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V D853 8-719-404-49 DIODE MA111-TX C807 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V D854 8-719-404-49 DIODE MA111-TX C808 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D903 8-713-102-80 DIODE 1T369-01-T8A C810 1-104-851-11 TANTAL. CHIP 10uF 20% 10V D904 8-719-976-96 DIODE MA8047-H-TX C811 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V D905 8-713-102-80 DIODE 1T369-01-T8A C812 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V < IC > C813 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C814 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V IC601 8-759-535-05 IC BH9530KS2 C815 1-104-851-11 TANTAL. CHIP 10uF 20% 10V IC801 8-759-530-19 IC MB40D001PFV-G-BND-ER C851 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC802 8-759-486-77 IC IR3Y37M4 C852 1-113-981-11 TANTAL. CHIP 22uF 20% 20V IC851 8-759-521-35 IC TL5001CDR IC852 8-759-075-70 IC TA75S393F-TE85R C853 1-163-081-00 CERAMIC CHIP 0.22uF 25V C854 1-135-149-21 TANTALUM CHIP 2.2uF 20% 10V IC901 8-759-530-20 IC CM7017L3-T4 C855 1-164-505-11 CERAMIC CHIP 2.2uF 16V IC902 8-759-327-01 IC NJM062V(TE2) C856 1-162-918-11 CERAMIC CHIP 18PF 5% 50V IC903 8-759-523-03 IC TC74HC4066AFS-EL C857 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V < COIL > C858 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C859 1-162-920-11 CERAMIC CHIP 27PF 5% 50V L601 1-414-394-11 INDUCTOR 2.2uH C861 1-104-911-11 TANTAL. CHIP 33uF 20% 10V L701 1-412-067-21 INDUCTOR CHIP 330uH C862 1-164-346-11 CERAMIC CHIP 1uF 16V L801 1-414-402-11 INDUCTOR 47uH C863 1-164-661-11 CERAMIC CHIP 0.018uF 10% 50V L802 1-414-078-11 INDUCTOR 10uH L851 1-414-396-21 INDUCTOR 4.7uH C865 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V !C866 1-113-521-11 CERAMIC CHIP 12PF 10% 3KV L852 1-424-674-11 INDUCTOR 0uH C867 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V L853 1-409-536-41 INDUCTOR 0uH C901 1-135-259-11 TANTAL. CHIP 10uF 20% 6.3V L901 1-414-754-11 INDUCTOR 10uH C902 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V L902 1-414-754-11 INDUCTOR 10uH L903 1-412-951-11 INDUCTOR 10uH C903 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C904 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V L904 1-414-754-11 INDUCTOR 10uH C905 1-110-501-11 CERAMIC CHIP 0.33uF 10% 16V L905 1-412-953-11 INDUCTOR 15uH C906 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C907 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une 6-9 specified. pièce portant le numéro spécifié.,

PK-43 (CASIO)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < TRANSISTOR > R711 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R712 1-216-829-11 METAL CHIP 4.7K 5% 1/16W Q701 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R713 1-216-823-11 METAL CHIP 1.5K 5% 1/16W Q702 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q851 8-729-042-72 TRANSISTOR UN9214J-(K8).SO R714 1-216-815-11 METAL CHIP 330 5% 1/16W Q852 8-729-042-59 TRANSISTOR UN9112J-(K8).SO R715 1-216-826-11 METAL CHIP 2.7K 5% 1/16W Q853 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R716 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R717 1-216-841-11 METAL CHIP 47K 5% 1/16W Q854 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R801 1-216-864-11 METAL CHIP 0 5% 1/16W Q855 8-729-037-74 TRANSISTOR UN9213J-(K8).SO Q856 8-729-823-84 TRANSISTOR FP102-TL R804 1-216-837-11 METAL CHIP 22K 5% 1/16W Q857 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R805 1-216-834-11 METAL CHIP 12K 5% 1/16W Q858 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO R806 1-216-841-11 METAL CHIP 47K 5% 1/16W R812 1-216-845-11 METAL CHIP 100K 5% 1/16W Q859 8-729-037-74 TRANSISTOR UN9213J-(K8).SO R813 1-216-805-11 METAL CHIP 47 5% 1/16W Q860 8-729-039-43 TRANSISTOR FP216-TL Q862 8-729-042-59 TRANSISTOR UN9112J-(K8).SO R814 1-216-805-11 METAL CHIP 47 5% 1/16W Q903 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX R815 1-216-805-11 METAL CHIP 47 5% 1/16W Q904 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R816 1-216-864-11 METAL CHIP 0 5% 1/16W R822 1-216-843-11 METAL CHIP 68K 5% 1/16W Q905 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX R823 1-216-834-11 METAL CHIP 12K 5% 1/16W Q906 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX R826 1-216-864-11 METAL CHIP 0 5% 1/16W < RESISTOR > R827 1-216-835-11 METAL CHIP 15K 5% 1/16W R828 1-216-839-11 METAL CHIP 33K 5% 1/16W R601 1-216-033-00 METAL CHIP 220 5% 1/10W R852 1-218-867-11 RES,CHIP 6.8K 0.50% 1/16W R602 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R853 1-218-881-11 RES,CHIP 27K 0.50% 1/16W R603 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R604 1-216-845-11 METAL CHIP 100K 5% 1/16W R854 1-218-897-11 RES,CHIP 120K 0.50% 1/16W R605 1-216-298-00 METAL CHIP 2.2 5% 1/10W R855 1-216-818-11 METAL CHIP 560 5% 1/16W R856 1-216-837-11 METAL CHIP 22K 5% 1/16W R606 1-218-707-11 RES,CHIP 4.3K 5% 1/16W R857 1-216-818-11 METAL CHIP 560 5% 1/16W R607 1-218-707-11 RES,CHIP 4.3K 5% 1/16W R858 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R608 1-216-864-11 METAL CHIP 0 5% 1/16W R610 1-216-864-11 METAL CHIP 0 5% 1/16W R859 1-218-871-11 RES,CHIP 10K 0.50% 1/16W R612 1-218-851-11 RES,CHIP 1.5K 0.50% 1/16W R860 1-218-854-11 RES,CHIP 2K 0.50% 1/16W R861 1-218-859-11 RES,CHIP 3.3K 0.50% 1/16W R613 1-218-869-11 RES,CHIP 8.2K 0.50% 1/16W R862 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R614 1-218-863-11 RES,CHIP 4.7K 0.50% 1/16W R863 1-216-841-11 METAL CHIP 47K 5% 1/16W R615 1-218-859-11 RES,CHIP 3.3K 0.50% 1/16W R618 1-218-887-11 RES,CHIP 47K 0.50% 1/16W R864 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R619 1-218-849-11 RES,CHIP 1.2K 0.50% 1/16W R865 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R867 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R620 1-216-821-11 METAL CHIP 1K 5% 1/16W R868 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R621 1-218-847-11 RES,CHIP 1K 0.50% 1/16W R870 1-216-845-11 METAL CHIP 100K 5% 1/16W R622 1-218-875-11 RES,CHIP 15K 0.50% 1/16W R623 1-218-292-11 RES,CHIP 20K 5% 1/16W R871 1-216-831-11 METAL CHIP 6.8K 5% 1/16W R624 1-216-817-11 METAL CHIP 470 5% 1/16W R872 1-216-837-11 METAL CHIP 22K 5% 1/16W R873 1-216-817-11 METAL CHIP 470 5% 1/16W R625 1-216-833-11 METAL CHIP 10K 5% 1/16W R874 1-216-810-11 METAL CHIP 120 5% 1/16W R626 1-216-835-11 METAL CHIP 15K 5% 1/16W R901 1-216-864-11 METAL CHIP 0 5% 1/16W R627 1-216-833-11 METAL CHIP 10K 5% 1/16W R628 1-216-835-11 METAL CHIP 15K 5% 1/16W R902 1-216-864-11 METAL CHIP 0 5% 1/16W R629 1-216-835-11 METAL CHIP 15K 5% 1/16W R905 1-216-855-11 METAL CHIP 680K 5% 1/16W R906 1-216-864-11 METAL CHIP 0 5% 1/16W R630 1-216-833-11 METAL CHIP 10K 5% 1/16W R908 1-216-846-11 METAL CHIP 120K 5% 1/16W R631 1-216-857-11 METAL CHIP 1M 5% 1/16W R912 1-216-842-11 METAL CHIP 56K 5% 1/16W R632 1-216-833-11 METAL CHIP 10K 5% 1/16W R701 1-216-824-11 METAL CHIP 1.8K 5% 1/16W R913 1-216-833-11 METAL CHIP 10K 5% 1/16W R702 1-216-819-11 METAL CHIP 680 5% 1/16W R915 1-216-857-11 METAL CHIP 1M 5% 1/16W R916 1-216-837-11 METAL CHIP 22K 5% 1/16W R703 1-216-819-11 METAL CHIP 680 5% 1/16W R918 1-216-843-11 METAL CHIP 68K 5% 1/16W R705 1-216-824-11 METAL CHIP 1.8K 5% 1/16W R920 1-218-897-11 RES,CHIP 120K 0.50% 1/16W R706 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R707 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R921 1-216-843-11 METAL CHIP 68K 5% 1/16W R708 1-216-824-11 METAL CHIP 1.8K 5% 1/16W R922 1-216-841-11 METAL CHIP 47K 5% 1/16W R924 1-218-897-11 RES,CHIP 120K 0.50% 1/16W R709 1-216-851-11 METAL CHIP 330K 5% 1/16W R926 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R710 1-216-847-11 METAL CHIP 150K 5% 1/16W R929 1-216-845-11 METAL CHIP 100K 5% 1/16W 6-10,

PK-43 (CASIO) PK-43 (SHARP)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R930 1-216-839-11 METAL CHIP 33K 5% 1/16W A-7093-881-A PK-43 (SHARP) BOARD, COMPLETE R932 1-216-845-11 METAL CHIP 100K 5% 1/16W (SERVICE) R933 1-216-845-11 METAL CHIP 100K 5% 1/16W ************************************* R934 1-216-864-11 METAL CHIP 0 5% 1/16W (Ref.No.:2,000 Series) R935 1-216-864-11 METAL CHIP 0 5% 1/16W < BATTERY HOLDER > R936 1-216-864-11 METAL CHIP 0 5% 1/16W R937 1-216-864-11 METAL CHIP 0 5% 1/16W BH701 1-550-104-32 HOLDER, BATTERY R938 1-216-845-11 METAL CHIP 100K 5% 1/16W R939 1-216-839-11 METAL CHIP 33K 5% 1/16W < BUZZER > R940 1-216-864-11 METAL CHIP 0 5% 1/16W BZ701 1-529-107-11 BUZZER, PIEZOELECTRIC R942 1-216-864-11 METAL CHIP 0 5% 1/16W R950 1-216-864-11 METAL CHIP 0 5% 1/16W < CAPACITOR > R951 1-216-864-11 METAL CHIP 0 5% 1/16W R952 1-216-864-11 METAL CHIP 0 5% 1/16W C601 1-109-982-11 CERAMIC CHIP 1uF 10% 10V R953 1-216-864-11 METAL CHIP 0 5% 1/16W C602 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C603 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R954 1-216-864-11 METAL CHIP 0 5% 1/16W C604 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R955 1-216-864-11 METAL CHIP 0 5% 1/16W C605 1-113-642-11 TANTAL. CHIP 47uF 20% 10V R957 1-216-864-11 METAL CHIP 0 5% 1/16W R959 1-216-864-11 METAL CHIP 0 5% 1/16W C606 1-113-642-11 TANTAL. CHIP 47uF 20% 10V R962 1-216-836-11 METAL CHIP 18K 5% 1/16W C701 1-113-991-11 TANTAL. CHIP 33uF 20% 16V C702 1-107-682-11 CERAMIC CHIP 1uF 10% 16V R963 1-216-864-11 METAL CHIP 0 5% 1/16W C703 1-165-320-11 CERAMIC CHIP 0.47uF 10% 16V R966 1-216-864-11 METAL CHIP 0 5% 1/16W C801 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R970 1-216-805-11 METAL CHIP 47 5% 1/16W R971 1-216-805-11 METAL CHIP 47 5% 1/16W C802 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R972 1-216-805-11 METAL CHIP 47 5% 1/16W C803 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C804 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R973 1-216-857-11 METAL CHIP 1M 5% 1/16W C805 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R974 1-216-864-11 METAL CHIP 0 5% 1/16W C806 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V R975 1-216-864-11 METAL CHIP 0 5% 1/16W R978 1-216-841-11 METAL CHIP 47K 5% 1/16W C807 1-110-569-11 TANTAL. CHIP 47uF 20% 6.3V R979 1-216-841-11 METAL CHIP 47K 5% 1/16W C808 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C810 1-104-851-11 TANTAL. CHIP 10uF 20% 10V R980 1-216-864-11 METAL CHIP 0 5% 1/16W C811 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V R981 1-216-829-11 METAL CHIP 4.7K 5% 1/16W C812 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V < VARIABLE RESISTOR > C813 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C814 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V RV701 1-225-224-11 RES, VAR (ZOOM) 10K (ZOOM) C815 1-104-851-11 TANTAL. CHIP 10uF 20% 10V C851 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < SWITCH > C852 1-113-981-11 TANTAL. CHIP 22uF 20% 20V S701 1-771-128-11 SWITCH, TACTILE (CONTROL) C853 1-163-081-00 CERAMIC CHIP 0.22uF 25V S702 1-572-467-21 SWITCH, PUSH (1 KEY) (POWER) C854 1-135-149-21 TANTALUM CHIP 2.2uF 20% 10V S703 1-771-106-11 SWITCH, TACTILE (PICTURE EFFECT) C855 1-164-505-11 CERAMIC CHIP 2.2uF 16V S704 1-771-106-11 SWITCH, TACTILE (DISPLAY) C856 1-162-918-11 CERAMIC CHIP 18PF 5% 50V S705 1-771-106-11 SWITCH, TACTILE (FLASH) C857 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V S706 1-771-106-11 SWITCH, TACTILE (BRIGHT +) C858 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V S707 1-771-106-11 SWITCH, TACTILE (PROGRAM AE) C859 1-162-920-11 CERAMIC CHIP 27PF 5% 50V S708 1-762-741-11 SWITCH, SLIDE (PLAY/CAMERA) C861 1-104-911-11 TANTAL. CHIP 33uF 20% 10V S709 1-771-106-11 SWITCH, TACTILE (BRIGHT -) C862 1-164-346-11 CERAMIC CHIP 1uF 16V S710 1-762-741-11 SWITCH, SLIDE (LCD BACKLIGHT) C863 1-164-661-11 CERAMIC CHIP 0.018uF 10% 50V < TRANSFORMER > C865 1-107-725-11 CERAMIC CHIP 0.1uF 10% 16V !C866 1-113-521-11 CERAMIC CHIP 12PF 10% 3KV !T851 1-431-861-21 TRANSFORMER, INVERTER C867 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C902 1-107-687-11 TANTAL. CHIP 3.3uF 20% 20V C903 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C904 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C905 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C906 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une 6-11 specified. pièce portant le numéro spécifié.,

PK-43 (SHARP)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C907 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C908 1-162-926-11 CERAMIC CHIP 82PF 5% 50V Q701 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q702 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO C909 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V Q851 8-729-042-72 TRANSISTOR UN9214J-(K8).SO C911 1-164-739-11 CERAMIC CHIP 560PF 5% 50V Q852 8-729-042-59 TRANSISTOR UN9112J-(K8).SO C913 1-162-926-11 CERAMIC CHIP 82PF 5% 50V Q853 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C915 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C916 1-113-994-11 TANTAL. CHIP 6.8uF 20% 16V Q854 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO Q855 8-729-037-74 TRANSISTOR UN9213J-(K8).SO C917 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q856 8-729-823-84 TRANSISTOR FP102-TL C918 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q857 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO C919 1-107-689-21 TANTAL. CHIP 1uF 20% 35V Q858 8-729-037-52 TRANSISTOR 2SD2216J-QR(K8).SO C920 1-107-682-11 CERAMIC CHIP 1uF 10% 16V C925 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V Q859 8-729-037-74 TRANSISTOR UN9213J-(K8).SO Q860 8-729-039-43 TRANSISTOR FP216-TL C926 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V Q862 8-729-042-59 TRANSISTOR UN9112J-(K8).SO Q903 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX < CONNECTOR > Q904 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX CN601 1-764-526-11 CONNECTOR, FFC/FPC 18P Q905 8-729-230-63 TRANSISTOR 2SD1819A-QRS-TX * CN602 1-750-075-11 CONNECTOR, FFC/FPC 10P Q906 8-729-420-24 TRANSISTOR 2SB1218A-QRS-TX CN603 1-778-598-21 CONNECTOR, BOARD TO BOARD 60P CN802 1-764-526-11 CONNECTOR, FFC/FPC 18P < RESISTOR > CN851 1-573-929-11 CONNECTOR, FFC/FPC (ZIF) 20P R601 1-216-033-00 METAL CHIP 220 5% 1/10W CN901 1-691-388-11 CONNECTOR, FFC/FPC (ZIF) 24P R602 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R603 1-216-825-11 METAL CHIP 2.2K 5% 1/16W < DIODE > R604 1-216-845-11 METAL CHIP 100K 5% 1/16W R605 1-216-298-00 METAL CHIP 2.2 5% 1/10W D701 8-719-061-82 DIODE TLSU1002(TPX1,SONY) (ACCESS) D702 8-719-061-81 DIODE TLYU1002(TPX1,SONY) R606 1-218-707-11 RES,CHIP 4.3K 5% 1/16W (FLASH CHARG) R607 1-218-707-11 RES,CHIP 4.3K 5% 1/16W D852 8-719-404-49 DIODE MA111-TX R608 1-216-864-11 METAL CHIP 0 5% 1/16W R610 1-216-864-11 METAL CHIP 0 5% 1/16W D853 8-719-404-49 DIODE MA111-TX R612 1-218-851-11 RES,CHIP 1.5K 0.50% 1/16W D854 8-719-404-49 DIODE MA111-TX D903 8-713-102-80 DIODE 1T369-01-T8A R613 1-218-869-11 RES,CHIP 8.2K 0.50% 1/16W D904 8-719-976-96 DIODE MA8047-H-TX R614 1-218-863-11 RES,CHIP 4.7K 0.50% 1/16W D905 8-713-102-80 DIODE 1T369-01-T8A R615 1-218-859-11 RES,CHIP 3.3K 0.50% 1/16W R618 1-218-887-11 RES,CHIP 47K 0.50% 1/16W < IC > R619 1-218-849-11 RES,CHIP 1.2K 0.50% 1/16W IC601 8-759-535-05 IC BH9530KS2 R620 1-216-821-11 METAL CHIP 1K 5% 1/16W IC801 8-759-530-19 IC MB40D001PFV-G-BND-ER R621 1-218-847-11 RES,CHIP 1K 0.50% 1/16W IC802 8-759-486-77 IC IR3Y37M4 R622 1-218-875-11 RES,CHIP 15K 0.50% 1/16W IC851 8-759-521-35 IC TL5001CDR R623 1-218-292-11 RES,CHIP 20K 5% 1/16W IC852 8-759-075-70 IC TA75S393F-TE85R R624 1-216-817-11 METAL CHIP 470 5% 1/16W IC901 8-759-495-00 IC LZ9GH184 R625 1-216-833-11 METAL CHIP 10K 5% 1/16W IC902 8-759-327-01 IC NJM062V(TE2) R626 1-216-835-11 METAL CHIP 15K 5% 1/16W IC903 8-759-523-03 IC TC74HC4066AFS-EL R627 1-216-833-11 METAL CHIP 10K 5% 1/16W R628 1-216-835-11 METAL CHIP 15K 5% 1/16W < COIL > R629 1-216-835-11 METAL CHIP 15K 5% 1/16W L601 1-414-394-11 INDUCTOR 2.2uH R630 1-216-833-11 METAL CHIP 10K 5% 1/16W L701 1-412-067-21 INDUCTOR CHIP 330uH R631 1-216-857-11 METAL CHIP 1M 5% 1/16W L801 1-414-402-11 INDUCTOR 47uH R632 1-216-833-11 METAL CHIP 10K 5% 1/16W L802 1-414-078-11 INDUCTOR 10uH R701 1-216-824-11 METAL CHIP 1.8K 5% 1/16W L851 1-414-396-21 INDUCTOR 4.7uH R702 1-216-819-11 METAL CHIP 680 5% 1/16W L852 1-424-674-11 INDUCTOR 0uH R703 1-216-819-11 METAL CHIP 680 5% 1/16W L853 1-409-536-41 INDUCTOR 0uH R705 1-216-824-11 METAL CHIP 1.8K 5% 1/16W L901 1-414-754-11 INDUCTOR 10uH R706 1-216-826-11 METAL CHIP 2.7K 5% 1/16W L902 1-414-754-11 INDUCTOR 10uH R707 1-216-826-11 METAL CHIP 2.7K 5% 1/16W L903 1-412-951-11 INDUCTOR 10uH R708 1-216-824-11 METAL CHIP 1.8K 5% 1/16W L905 1-412-953-11 INDUCTOR 15uH R709 1-216-851-11 METAL CHIP 330K 5% 1/16W R710 1-216-847-11 METAL CHIP 150K 5% 1/16W < TRANSISTOR > R711 1-216-829-11 METAL CHIP 4.7K 5% 1/16W 6-12,

PK-43 (SHARP)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R712 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R927 1-216-864-11 METAL CHIP 0 5% 1/16W R713 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R929 1-216-845-11 METAL CHIP 100K 5% 1/16W R714 1-216-815-11 METAL CHIP 330 5% 1/16W R930 1-216-839-11 METAL CHIP 33K 5% 1/16W R715 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R931 1-216-864-11 METAL CHIP 0 5% 1/16W R716 1-216-826-11 METAL CHIP 2.7K 5% 1/16W R932 1-216-845-11 METAL CHIP 100K 5% 1/16W R717 1-216-841-11 METAL CHIP 47K 5% 1/16W R933 1-216-845-11 METAL CHIP 100K 5% 1/16W R801 1-216-864-11 METAL CHIP 0 5% 1/16W R934 1-216-864-11 METAL CHIP 0 5% 1/16W R804 1-216-837-11 METAL CHIP 22K 5% 1/16W R935 1-216-864-11 METAL CHIP 0 5% 1/16W R805 1-216-834-11 METAL CHIP 12K 5% 1/16W R938 1-216-845-11 METAL CHIP 100K 5% 1/16W R806 1-216-841-11 METAL CHIP 47K 5% 1/16W R939 1-216-839-11 METAL CHIP 33K 5% 1/16W R812 1-216-845-11 METAL CHIP 100K 5% 1/16W R940 1-216-864-11 METAL CHIP 0 5% 1/16W R813 1-216-805-11 METAL CHIP 47 5% 1/16W R941 1-218-883-11 RES,CHIP 33K 0.50% 1/16W R814 1-216-805-11 METAL CHIP 47 5% 1/16W R942 1-218-879-11 RES,CHIP 22K 0.50% 1/16W R815 1-216-805-11 METAL CHIP 47 5% 1/16W R943 1-218-883-11 RES,CHIP 33K 0.50% 1/16W R816 1-216-833-11 METAL CHIP 10K 5% 1/16W R944 1-218-879-11 RES,CHIP 22K 0.50% 1/16W R822 1-216-840-11 METAL CHIP 39K 5% 1/16W R945 1-216-864-11 METAL CHIP 0 5% 1/16W R823 1-216-834-11 METAL CHIP 12K 5% 1/16W R946 1-216-864-11 METAL CHIP 0 5% 1/16W R826 1-216-864-11 METAL CHIP 0 5% 1/16W R947 1-216-864-11 METAL CHIP 0 5% 1/16W R827 1-216-835-11 METAL CHIP 15K 5% 1/16W R948 1-216-864-11 METAL CHIP 0 5% 1/16W R828 1-216-839-11 METAL CHIP 33K 5% 1/16W R949 1-216-864-11 METAL CHIP 0 5% 1/16W R852 1-218-867-11 RES,CHIP 6.8K 0.50% 1/16W R956 1-216-864-11 METAL CHIP 0 5% 1/16W R853 1-218-881-11 RES,CHIP 27K 0.50% 1/16W R958 1-216-864-11 METAL CHIP 0 5% 1/16W R854 1-218-897-11 RES,CHIP 120K 0.50% 1/16W R960 1-216-864-11 METAL CHIP 0 5% 1/16W R855 1-216-818-11 METAL CHIP 560 5% 1/16W R961 1-216-864-11 METAL CHIP 0 5% 1/16W R856 1-216-837-11 METAL CHIP 22K 5% 1/16W R964 1-216-864-11 METAL CHIP 0 5% 1/16W R857 1-216-818-11 METAL CHIP 560 5% 1/16W R965 1-216-864-11 METAL CHIP 0 5% 1/16W R858 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R967 1-216-805-11 METAL CHIP 47 5% 1/16W R859 1-218-871-11 RES,CHIP 10K 0.50% 1/16W R968 1-216-805-11 METAL CHIP 47 5% 1/16W R860 1-218-854-11 RES,CHIP 2K 0.50% 1/16W R969 1-216-805-11 METAL CHIP 47 5% 1/16W R861 1-218-859-11 RES,CHIP 3.3K 0.50% 1/16W R973 1-216-857-11 METAL CHIP 1M 5% 1/16W R862 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R974 1-216-864-11 METAL CHIP 0 5% 1/16W R863 1-216-841-11 METAL CHIP 47K 5% 1/16W R975 1-216-864-11 METAL CHIP 0 5% 1/16W R864 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R978 1-216-841-11 METAL CHIP 47K 5% 1/16W R865 1-216-823-11 METAL CHIP 1.5K 5% 1/16W R979 1-216-841-11 METAL CHIP 47K 5% 1/16W R867 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R980 1-216-864-11 METAL CHIP 0 5% 1/16W R868 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R981 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R870 1-216-845-11 METAL CHIP 100K 5% 1/16W < VARIABLE RESISTOR > R871 1-216-831-11 METAL CHIP 6.8K 5% 1/16W R872 1-216-837-11 METAL CHIP 22K 5% 1/16W RV701 1-225-224-11 RES, VAR (ZOOM) 10K (ZOOM) R873 1-216-817-11 METAL CHIP 470 5% 1/16W R874 1-216-810-11 METAL CHIP 120 5% 1/16W < SWITCH > R903 1-216-864-11 METAL CHIP 0 5% 1/16W S701 1-771-128-11 SWITCH, TACTILE (CONTROL) R905 1-216-855-11 METAL CHIP 680K 5% 1/16W S702 1-572-467-21 SWITCH, PUSH (1 KEY) (POWER) R908 1-216-846-11 METAL CHIP 120K 5% 1/16W S703 1-771-106-11 SWITCH, TACTILE (PICTURE EFFECT) R912 1-216-845-11 METAL CHIP 100K 5% 1/16W S704 1-771-106-11 SWITCH, TACTILE (DISPLAY) R913 1-216-833-11 METAL CHIP 10K 5% 1/16W S705 1-771-106-11 SWITCH, TACTILE (FLASH) R914 1-216-857-11 METAL CHIP 1M 5% 1/16W S706 1-771-106-11 SWITCH, TACTILE (BRIGHT +) R915 1-216-857-11 METAL CHIP 1M 5% 1/16W S707 1-771-106-11 SWITCH, TACTILE (PROGRAM AE) R916 1-216-837-11 METAL CHIP 22K 5% 1/16W S708 1-762-741-11 SWITCH, SLIDE (PLAY/CAMERA) R918 1-216-843-11 METAL CHIP 68K 5% 1/16W S709 1-771-106-11 SWITCH, TACTILE (BRIGHT -) R920 1-218-901-11 RES,CHIP 180K 0.50% 1/16W S710 1-762-741-11 SWITCH, SLIDE (LCD BACKLIGHT) R921 1-216-843-11 METAL CHIP 68K 5% 1/16W < TRANSFORMER > R922 1-216-841-11 METAL CHIP 47K 5% 1/16W R924 1-218-901-11 RES,CHIP 180K 0.50% 1/16W !T851 1-431-861-21 TRANSFORMER, INVERTER R926 1-216-829-11 METAL CHIP 4.7K 5% 1/16W Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une 6-13 specified. pièce portant le numéro spécifié.,

RL-50

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-7073-591-A RL-50 BOARD, COMPLETE 3-864-060-41 MANUAL, INSTRUCTION (for BC-V615) ********************* (SWEDISH) (AEP) (Ref.No.:1,000 Series) 3-987-015-01 BELT (S), SHOULDER X-3948-880-1 CAP ASSY, LENS < CONNECTOR > ! A-7029-111-A BC-V615 AC POWER ADAPTOR CN051 1-770-620-21 PIN, CONNECTOR 3P ** NP-F330 (Note 2) < SWITCH > S051 1-771-184-11 SWITCH, TACTILE (SHUTTER)

MISCELLANEOUS

************** 11 1-694-297-11 TERMINAL BOARD, BATTERY !13 1-475-832-11 FLASH UNIT 14 1-475-842-11 MF BLOCK 16 1-958-849-11 HARNESS (FF-188) 57 1-759-679-11 DRIVE, FLOPPY DISK (3.5inch) (Note 1) 68 1-670-486-21 FP-35 FLEXIBLE BOARD 101 1-758-177-11 LENS, ZOOM (VCL-4210VD) 102 1-670-487-11 FP-34 FLEXIBLE BOARD 106 1-758-204-11 FILTER BLOCK, OPTICAL IC401 A-7030-901-A CCD BLOCK ASSY LCD901 1-803-036-21 INDICATOR MODULE, LIQUID CRYSTAL (SHARP) LCD901 1-803-184-21 INDICATOR MODULE, LIQUID CRYSTAL (CASIO) M901 3-709-404-01 MOTOR UNIT, FOCUS M902 3-709-403-01 MOTOR UNIT, ZOOM !ND801 1-517-787-11 TUBE, FLUORESCENT, COLD CATHODE ACCESSORIES & PACKING MATERIALS ******************************* ! 1-555-074-21 CORD, POWER (AUS) ! 1-559-437-11 CORD, POWER 2P (JE) ! 1-569-008-21 ADAPTOR, CONVERSION 2P (E) ! 1-573-856-11 ADAPTOR, CHANGE (JE) ! 1-769-608-11 CORD, POWER (AEP, UK, E, HK) ! 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK, HK) ! 1-775-549-21 CORD, POWER (US, CND) 3-862-986-11 MANUAL, INSTRUCTION (ENGLISH, SPANISH) 3-862-986-21 MANUAL, INSTRUCTION (CND, AEP, JE) (GERMAN, FRENCH) 3-862-986-31 MANUAL, INSTRUCTION (AEP) (ITALIAN, DUTCH) 3-862-986-41 MANUAL, INSTRUCTION (PORTUGUESE, RUSSIAN) (AEP, E, HK) Note 1 The FD block assembly is a mechanical unit 3-862-986-51 MANUAL, INSTRUCTION (CHINESE) (E, HK, JE) which has completely been adjusted in the 3-862-986-61 MANUAL, INSTRUCTION factory. So never disassemble the FD block (ARABIC, KOREAN) (E, HK, JE) assembly. 3-862-986-71 MANUAL, INSTRUCTION (SWEDISH) (AEP) 3-864-060-11 MANUAL, INSTRUCTION (for BC-V615) Note 2 ** marked part is available as an optional (ENGLISH, FRENCH, GERMAN, SPANISH) accessory. 3-864-060-21 MANUAL, INSTRUCTION (for BC-V615) * Be sure to read “Precautions for Replacement of (ITALIAN, DUTCH, PORTUGUESE, RUSSIAN) CCD Imager” on page 4-6 when changing the CCD (AEP, E, HK) 3-864-060-31 MANUAL, INSTRUCTION (for BC-V615) imager. (CHINESE, KOREAN, ARABIC) (E, HK, JE) Note : Note : The components identified by Les composants identifiés par mark ! or dotted line with mark une marque ! sont critiques ! are critical for safety. pour la sécurité. Replace only with part number Ne les remplacer que par une 6-14 specified. pièce portant le numéro spécifié.,

FOR CAMERA COLOR REPRODUCTION ADJUSTMENT (MVC-FD71)

Take a copy of CAMERA COLOR REPRODUCTION FRAME and Parts reference sheets with a clear sheet for use R-Y

MG R YL

B-Y

B G CY MVC-FD71

You can find the parts position of mount locations applying to FC-66 board of a set.

SIDE B

ABCDEFG14

I

CN101 CN401 4C0 108CI4 204CI 2 FC-66 BOARD 3 IC50332109CI 4 IC501 IC807 1 CN901ABCDEFG

SIDE A

CN910 IC804 CN602,

MVC-FD71 Sony Corporation 98F0570-1

Printed in Japan © 1998. 6 9-974-076-11 Personal A&V Products Company Published by Quarity Engineering Dept. – 130 – (Osaki East),

MVC-FD71 US Model Canadian Model SERVICE MANUAL AEP ModelUK Model

2000. 09 E Model

Australian Model Hong Kong Model SUPPLEMENT-1 Tourist Model

File this supplement with the service manual. (PV00-005) • Change of main frame assy. & : Points added portion. - : Points changed portion. 6-1. EXPLODED VIEWS (Service manual page 6-2) 6-1-2. CABINET (REAR) SECTION 56 ; _ 54 Former Type New Type Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 54 X-3948-765-1 FRAME ASSY, MAIN 54 X-3948-765-2 FRAME ASSY, MAIN [ 75 3-055-096-01 WASHER, METAL ) Sony Corporation 2000I0552-1Printed in Japan © 2000. 9 9-974-076-81 Personal VIDEO Products Company Published by Safety & Service Engineering Dept.]
15

Similar documents

MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model DIGITAL STILL CAMERA
MVC-FD75 SERVICE MANUAL US Model Canadian Model AEP Model UK Model Ver 1.0 2001. 01 E Model Hong Kong Model Australian Model Brazilian Model SPECIFICATIONS DIGITAL STILL CAMERA • Floppy disk that can be used by the MVC-FD75 • Size : 3.5-inch • Type : 2 HD • Capacity : 1.44 MB • Format : MS-DOS forma
LCD screen Mass (Approx.) NP-F330 battery pack
MVC-FD87/FD92 SERVICE MANUAL US Model Canadian Model Level 2 AEP Model UK Model E Model Ver 1.1 2001. 06 Hong Kong Model Australian Model Korea Model Japanese Model PHoto: MVC-FD92 This service manual contains information for Japanese model as well. When the machine needs to be repaired, please refe
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC
AVR055: Using a 32kHz XTAL for run-time calibration of the internal RC Features • Calibration using a 32 kHz external crystal • Adjustable RC frequency with maximum +/-2% accuracy • Tune RC oscillator at any operating voltage and temperature • Tune RC oscillator to any frequency within specification
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 1981A–AVR–03/05 AVR155: Accessing an I2C LCD Display using the AVR® 2-wire Serial Interface Features • Compatible with Philips' I2C protocol • 2-wire Serial Interface Master Driver for Easy Transmit and Receive Function • Initialization and Use ofa2x1
AVR107: Interfacing AVR serial memories
AVR107: Interfacing AVR serial memories Features • Devices: AT25128A/256A, AT25F1024/2048/4096 • Full Serial Memory Functions Support • Memory Array Burst Read • Page Burst Write • Write Protection Detection • On Going Access Detection • Non-blocking Write Access • Access Status Information 1 Introd
AVR120: Characterization and Calibration of the ADC on an AVR
AVR120: Characterization and Calibration of the ADC on an AVR Features • Understanding Analog to Digital Converter (ADC) characteristics • Measuring parameters describing ADC characteristics • Temperature, frequency and supply voltage dependencies • Compensating for offset and gain error Introductio
AVR001 Conditional Assembly and portability macros
AVR001 Conditional Assembly and portability macros Features • Increased portability • Easier Code Writing • Simplified I/O Register Access • Improved Assembly Status Feedback 1 Introduction This application note describes the Conditional Assembly feature present in the AVR Assembler version 1.74 and
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2527A–AVR–9/02 AVR223: Digital Filters with AVR Features • Implementations of Simple Digital Filters • Coefficient and Data Scaling • Fast Implementation of 2nd Order FIR Filter • Compact Implementation Of 8th Order FIR Filter • Fast Implementation of 2nd
8-bit Microcontroller Application Note AVR040: EMC Design Considerations Scope
8-bit Microcontroller Application Note Rev. 1619C–AVR–01/04 AVR040: EMC Design Considerations Scope This application note covers the most common EMC problems designers encounter when using microcontrollers. It will briefly discuss the various phenomena. The refer- ence literature covers EMC design i
8-bit RISC Microcontroller Application Note
8-bit RISC Microcontroller Application Note Rev. 2508B–AVR–01/04 AVR182: Zero Cross Detector Features • Interrupt Driven • Modular C Source Code • Size Efficient Code • Accurate and Fast Detection • A Minimum of External Components Introduction One of the many issues with developing modern applicati
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity,
AVR242: 8-bit Microcontroller Multiplexing LED Drive anda4x4Keypad Multiplexing Features reduced to fifteen with a bit of ingenuity, allowing the smaller 20-pin AVR to be LED Drive and a • 16 Key Pushbutton Pad in4x4Matrix • 4 Digit Multiplexed LED Display with used. The circuit diagram is shown in
8-bit Microcontroller Application Note AVR180: External Brown-out Protection
8-bit Microcontroller Application Note Rev. 1051B–AVR–05/02 AVR180: External Brown-out Protection Features • Low-voltage Detector • Prevent Register and EEPROM Corruption • Two Discrete Solutions • Integrated IC Solution • Extreme Low-cost Solution • Extreme Low-power Solution • Formulas for Compone
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 1259D–AVR–04/05 AVR134: Real Time Clock (RTC) using the Asynchronous Timer Features • Real Time Clock with Very Low Power Consumption (4 µA @ 3.3V) • Very Low Cost Solution • Adjustable Prescaler to Adjust Precision • Counts Time, Date, Month, and Year wit
  Wiring Diagram
Wiring Diagram Samsung Electronics 6-1
8-bit Microcntroller Application Note
8-bit Microcntroller Application Note Rev. 2532A–AVR–01/03 AVR243: Matrix Keyboard Decoder Features • 64-key Push-button Keyboard in8x8Matrix • No External Components Required • Wakes Up from Sleep Mode on Keypress • Easily Implemented into Other Applications • Low Power Consumption • Software Conta
  Alignment and Adjustments
Alignment and Adjustments 1. Tuner FM THD Adjustment FMOutput Antenna GND SETSSG FREQ. 98 MHz Terminal Oscilloscope Adjustment FM S.S.G Input point FM DETECTOR COIL Speaker (FM DET) Terminal output Input Output 60 dB Distortion Meter Minumum Distortion (0.4% below) (Figure 1-1) Figure1-1 IF CENTER
8-bit Microcontroller Application Note
8-bit Microcontroller Application Note Rev. 2540A–AVR–07/03 AVR104: Buffered Interrupt Controlled EEPROM Writes Features • Flexible Multi-byte EEPROM Buffer • Power Efficient EEPROM Access • Access Control on Buffers • EEPROM Buffer Rewrite Introduction Many applications use the built-in EEPROM of t
  Schematic Diagram - This Document can not be used without Samsung’s authorization -
Schematic Diagram - This Document can not be used without Samsung’s authorization - 7-1 MAIN 7-1 Samsung Electronics 7-2 FRONT - This Document can not be used without Samsung’s authorization - Samsung Electronics 7-2 7-3 DSP - This Document can not be used without Samsung’s authorization - 7-3 Sam
  TroubleShooting
TroubleShooting 9-1 Main 9-1 Samsung Electronics Samsung Electronics 9-2 9-3 Samsung Electronics Samsung Electronics 9-4 9-2 DVD Servo parts 9-5 Samsung Electronics Samsung Electronics 9-6 9-7 Samsung Electronics Samsung Electronics 9-8 9-9 Samsung Electronics Samsung Electronics 9-10 9-11 Samsung
AVR054: Run-time calibration of the internal RC oscillator
AVR054: Run-time calibration of the internal RC oscillator Features • Calibration of internal RC oscillator via UART • LIN 2.0 compatible synchronization/calibration to within +/-2% of target frequency • Alternate run-time synchronization/calibration to within +/-1% of target frequency • Support for
SERVICE Manual
DVD RECEIVER AMP HT-DB120 SERVICE Manual DVD RECEIVER AMP SYSTEM CONTENTS 1. Alignment and Adjustments 2. Exploded Views and Parts List 3. Electrical Parts List 4. Block Diagrams 5. PCB Diagrams 6. Wiring Diagram 7. Schematic Diagrams 8. IC block Diagrams 9.Troubleshooting - Confidential - ELECTRONI
8-bit Microcontroller Application Note AVR131: Using the AVR’s High-speed PWM
8-bit Microcontroller Application Note Rev. 2542A–AVR–09/03 AVR131: Using the AVR’s High-speed PWM Features • Analog Waveform Generation using PWM • High-speed Prescalable PWM Clock Introduction This application note is an introduction to the use of the high-speed Pulse Width Mod- ulator (PWM) avail
8-bit RISC Microcontroller Application Note AVR042: AVR® Hardware Design Considerations
8-bit RISC Microcontroller Application Note Rev. 2521B–AVR–01/04 AVR042: AVR® Hardware Design Considerations Features • Providing Robust Supply Voltage, Digital and Analog • Connecting the RESET Line • SPI Interface for In-System Programming • Using External Crystal or Ceramic Resonator Oscillators
8-bit Microcontroller Application Note AVR240: 4x4Keypad – Wake-up on Keypress Features Introduction
8-bit Microcontroller Application Note AVR240: 4x4Keypad – Wake-up on Keypress Features • 16 Key Pushbutton Pad in4x4Matrix • Very Low Power Consumption • AVR in Sleep Mode and Wakes Up on Keypress • Minimum External Components • ESD Protection Included if Necessary • Efficient Code • Complete Progr
Microcontrollers for Fluorescent and High Intensity Discharge Lamp Ballasts SMARTER, MORE FLEXIBLE LIGHTING SOLUTIONS
LIGHTINGMICROCONTROLLERSMicrocontrollers for Fluorescent and High Intensity Discharge Lamp Ballasts SMARTER, MORE FLEXIBLE LIGHTING SOLUTIONS Developed together with the industry leading lamp ballast manufac- turers, Atmel® microcontrollers are optimized for Linear and Dimmable Fluorescent tubes, as
AVR121: Enhancing ADC resolution by oversampling
AVR121: Enhancing ADC resolution by oversampling Features • Increasing the resolution by oversampling • Averaging and decimation • Noise reduction by averaging samples 1 Introduction Atmel’s AVR controller offers an Analog to Digital Converter with 10-bit resolution. In most cases 10-bit resolution
  IC Block Diagrams 8-1 Main
IC Block Diagrams 8-1 Main 8-1-1. FAN8082D 8-1 Samsung Electronics 8-1-2. LC87F66C8A Samsung Electronics 8-2 8-3 Samsung Electronics Samsung Electronics 8-4 8-5 Samsung Electronics 8-1-3. M62446AFP Samsung Electronics 8-6 8-7 Samsung Electronics 8-1-4. M66010FP 8-1-5. SI-8050SE 8-1-6. SI-8090JFE S
AVR053: Calibration of the internal RC oscillator Features Introduction
AVR053: Calibration of the internal RC oscillator Features • Calibration using STK500, AVRISP, JTAGICE or JTAGICE mkII • Calibration using 3rd party programmers • Adjustable RC frequency with +/-1% accuracy • Tune RC oscillator at any operating voltage and temperature • Tune RC oscillator to any fre
8-bit Microcontroller Application Note AVR230: DES Bootloader Features
8-bit Microcontroller Application Note Rev. 2541D–AVR–04/05 AVR230: DES Bootloader Features • Fits All AVR Microcontrollers with Bootloader Capabilities • Enables Secure Transfer of Compiled Software or Sensitive Data to Any AVR with Bootloader Capabilities • Includes Easy To Use, Configurable Examp
AVR106: C functions for reading and writing to Flash memory
AVR106: C functions for reading and writing to Flash memory Features • C functions for accessing Flash memory - Byte read - Page read - Byte write - Page write • Optional recovery on power failure • Functions can be used with any device having Self programming Program memory • Example project for us