Download: GENERAL DESCRIPTION QUICK REFERENCE DATA
GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load variations resulting in a very low worst case dissipation. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM Collector-emitter voltage peak value VBE = 0 V - 1500 V VCEO Collector-emitter voltage (open base) - 700 V IC Collector current (DC) - 8 A ICM Collector current peak value - 15...
Author:
Zając Shared: 8/19/19
Downloads: 1302 Views: 2832
Content
GENERAL DESCRIPTION
Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load variations resulting in a very low worst case dissipation.QUICK REFERENCE DATA
SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM Collector-emitter voltage peak value VBE = 0 V - 1500 V VCEO Collector-emitter voltage (open base) - 700 V IC Collector current (DC) - 8 A ICM Collector current peak value - 15 A Ptot Total power dissipation Ths ≤ 25 ˚C - 45 W VCEsat Collector-emitter saturation voltage IC = 4.5 A; IB = 1.29 A - 1.0 V VCEsat Collector-emitter saturation voltage IC = 4.5 A; IB = 1.1 A - 5.0 V ICsat Collector saturation current 4.5 - A tf Fall time ICM = 4.5 A; IB(end) = 1.1 A 0.4 0.6 µsPINNING - SOT399 PIN CONFIGURATION SYMBOL
PIN DESCRIPTION casec1base 2 collectorb3emitter case isolated123eLIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VCESM Collector-emitter voltage peak value VBE = 0 V - 1500 V VCEO Collector-emitter voltage (open base) - 700 V IC Collector current (DC) - 8 A ICM Collector current peak value - 15 A IB Base current (DC) - 4 A IBM Base current peak value - 6 A -IB(AV) Reverse base current average over any 20 ms period - 100 mA -IBM Reverse base current peak value 1 - 5 A Ptot Total power dissipation Ths ≤ 25 ˚C - 45 W Tstg Storage temperature -55 150 ˚C Tj Junction temperature - 150 ˚CTHERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT Rth j-hs Junction to heatsink without heatsink compound - 3.7 K/W Rth j-hs Junction to heatsink with heatsink compound - 2.8 K/W Rth j-a Junction to ambient in free air 35 - K/W 1 Turn-off current. December 1995 1 Rev 2.100,ISOLATION LIMITING VALUE & CHARACTERISTIC
Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Visol Repetitive peak voltage from all R.H. ≤ 65 % ; clean and dustfree - 2500 V three terminals to external heatsink Cisol Capacitance from T2 to external f = 1 MHz - 22 - pF heatsinkSTATIC CHARACTERISTICS
Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT ICES Collector cut-off current 2 VBE = 0 V; VCE = VCESMmax - - 1.0 mA ICES VBE = 0 V; VCE = VCESMmax; - - 2.0 mA Tj = 125 ˚C IEBO Emitter cut-off current VEB = 7.5 V; IC = 0 A - - 1.0 mA BVEBO Emitter-base breakdown voltage IB = 1 mA 7.5 13.5 - V VCEOsust Collector-emitter sustaining voltage IB = 0 A; IC = 100 mA; 700 - - V L = 25 mH VCEsat Collector-emitter saturation voltages IC = 4.5 A; IB = 1.1 A - - 5.0 V VCEsat IC = 4.5 A; IB = 1.29 A - - 1.0 V VBEsat Base-emitter saturation voltage IC = 4.5 A; IB = 1.7 A - - 1.3 V hFE DC current gain IC = 100 mA;VCE = 5V613 26 hFE IC = 4.5 A;VCE = 1V45.5 7.5DYNAMIC CHARACTERISTICS
Ths = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT Cc Collector capacitance IE = 0 A; VCB = 10 V; f = 1 MHz 80 - pF Switching times (16 kHz line ICM = 4.5 A; IB(end) = 1.1 A; LB = 6 µH; deflection circuit) -VBB = 4 V; (-dIB/dt = 0.6 A/µs) ts Turn-off storage time 5.0 6.0 µs tf Turn-off fall time 0.4 0.6 µs Switching times (38 kHz line ICM = 4.0 A; IB(end) = 0.9 A; LB = 6 µH; deflection circuit) -VBB = 4 V; (-dIB/dt = 0.6 A/µs) ts Turn-off storage time 4.7 5.7 µs tf Turn-off fall time 0.25 0.35 µs 2 Measured with half sine-wave voltage (curve tracer). December 1995 2 Rev 2.100,ICM
+ 50v 90 % 100-200RIC
10 % Horizontal tf t Oscilloscope tsIB
Vertical IBend 100R 1R t 6V 30-60 Hz - IBMFig.1. Test circuit for VCEOsust. Fig.4. Switching times definitions.
IC / mA + 150 v nominal adjust for ICM 1mH LB D.U.T. 100 IBend BY22812nF 0 -VBB VCE / V min VCEOsustFig.2. Oscilloscope display for VCEOsust. Fig.5. Switching times test circuit.
ICM h FE TRANSISTOR 100 IC DIODE t 5V IB IBend t 1V 20us 26us 64us Tj = 25 C Tj = 125 CVCE
0.01 0.1 1 10 t IC / AFig.3. Switching times waveforms. Fig.6. Typical DC current gain. hFE = f (IC)
parameter VCEDecember 1995 3 Rev 2.100
, VBESAT / V VCESAT / V 1.2 10 Tj = 25 C 1.1 Tj = 25 C Tj = 125 C Tj = 125 C 6A 0.9 4.5A 0.8 IC/IB= 1 0.7343A 0.6 5 IC=2A 0.5 0.4 0.1 0.1 1 10 0.1 1 10 IC / A IB / A Fig.7. Typical base-emitter saturation voltage. Fig.10. Typical collector-emitter saturation voltage. VBEsat = f (IC); parameter IC/IB VCEsat = f (IB); parameter IC VCESAT / V Eoff / uJ 1 1000 0.9 IC/IB= 0.8 5 IC = 4.5A 0.7 4 3.5A 0.6 3 0.5 100 Tj = 25 C 0.4 Tj = 125 C 0.3 0.2 0.1 0 10 0.1 1 10 0.1 1 10 IC / A IB / A Fig.8. Typical collector-emitter saturation voltage. Fig.11. Typical turn-off losses. Tj = 85˚C VCEsat = f (IC); parameter IC/IB Eoff = f (IB); parameter IC; f = 16 kHz VBESAT / V ts, tf / us 1.2 12 Tj = 25 C 11 ts 1.1 Tj = 125 C 10180.9 IC= 6 6A 5 0.8 4.5A 4 IC = 3A 3 4.5A 2A 0.7 2 3.5A tf 0.60012340.1 1 10 IB / A IB / A Fig.9. Typical base-emitter saturation voltage. Fig.12. Typical collector storage and fall time. VBEsat = f (IB); parameter IC ts = f (IB); tf = f (IB); parameter IC; Tj = 85˚C; f = 16 kHz December 1995 4 Rev 2.100, IC / A IC / A 100 100 = 0.01 = 0.01 ICM max ICM max tp = tp = 10 IC max 10 IC max II 10 us II 10 us Ptot max Ptot max11100 us 100 us 1 ms 1 msII0.1 0.1 10 ms 10 ms DC DC 0.01 0.01 1 10 100 1000 1 10 100 1000 VCE / V VCE / V Fig.13. Forward bias safe operating area. Ths = 25˚C Fig.15. Forward bias safe operating area. Ths = 25˚C I Region of permissible DC operation. I Region of permissible DC operation. II Extension for repetitive pulse operation. II Extension for repetitive pulse operation. NB: Mounted with heatsink compound and NB: Mounted without heatsink compound and 30 ± 5 newton force on the centre of 30 ± 5 newton force on the centre of the envelope. the envelope. PD% Normalised Power Derating120 with heatsink compound 0 20 40 60 80 100 120 140 Ths / C Fig.14. Normalised power dissipation. PD% = 100⋅PD/PD 25˚C = f (Ths) December 1995 5 Rev 2.100, MECHANICAL DATA Dimensions in mm 5.8 max Net Mass: 5.88 g 16.0 max 0.7 3.0 4.5 3.3 10.0 27 25 max 25.1 25.7 22.5 max 4.7 max 2.2 max 18.1 4.5 min 1.1 0.4 M 0.9 max 5.45 5.45 3.3 Fig.16. SOT399; The seating plane is electrically isolated from all terminals. Notes 1. Refer to mounting instructions for F-pack envelopes. 2. Epoxy meets UL94 V0 at 1/8". December 1995 6 Rev 2.100,DEFINITIONS
Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1995 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. December 1995 7 Rev 2.100]15
Similar documents

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load varia

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load varia

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load variations resu

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in high frequency electronic lighting ballast applications. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM Collector-emi

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic envelope intended for use in high frequency electronic lighting ballast applications. QUICK REFERENCE DATA SYMBOL PARAMETER CONDITIONS TYP. MAX. UNIT VCESM Collector-emitter volta

GENERAL DESCRIPTION Enhanced performance, new generation, high-voltage, high-speed switching npn transistor in a plastic full-pack envelope intended for use in horizontal deflection circuits of colour television receivers. Features exceptional tolerance to base drive and collector current load varia

HITFETBTS 917 Smart Lowside Power Switch Features Product Summary • Logic Level Input Drain source voltage VDS 60 V • Input Protection (ESD) On-state resistance RDS(on) 100 mΩ • Thermal Shutdown Current limit ID(lim) 1.5 A • Overload protection Nominal load current ID(ISO) 3.5 A • Short circuit prot

PROFET® BTS409L1 Smart Highside Power Switch Features Product Summary • Overload protection Overvoltage protection V • bb(AZ) 43 V Current limitation • V 5.0 ... 34 V Short circuit protection Operating voltage bb(on) • Thermal shutdown On-state resistance RON 200 mΩ • Overvoltage protection (includi

® BTB24 B STANDARD TRIACS .FEATURES.HIGH SURGE CURRENT CAPABILITYCOMMUTATION : (dV/dt)c > 10V/µs DESCRIPTION A1 The BTB24 B triac family are high performance A2 G glass passivated PNPN devices. These parts are suitables for general purpose ap- plications where high surge current capability is re- TO

IGBT Preliminary data • Low forward voltage drop • High switching speed • Low tail current • Latch-up free • Avalanche rated Pin 1 Pin 2 Pin3GCEType VCE IC Package Ordering Code BUP 314 1200V 52A TO-218 AB Q67040-A4206 Maximum Ratings Parameter Symbol Values Unit Collector-emitter voltage VCE 1200 V

IGBT Preliminary data • Low forward voltage drop • High switching speed • Low tail current • Latch-up free • Avalanche rated Pin 1 Pin 2 Pin3GCEType VCE IC Package Ordering Code BUP 213 1200V 32A TO-220 AB Q67040-A4407 Maximum Ratings Parameter Symbol Values Unit Collector-emitter voltage VCE 1200 V

IGBT • Low forward voltage drop • High switching speed • Low tail current • Latch-up free • Avalanche rated Pin 1 Pin 2 Pin3GCEType VCE IC Package Ordering Code BUP 212 1200V 22A TO-220 AB Q67040-A4 .4 .0 .8 .Maximum Ratings Parameter Symbol Values Unit Collector-emitter voltage VCE 1200 V Emitter-c

GENERAL DESCRIPTION QUICK REFERENCE DATA N-channel enhancement mode SYMBOL PARAMETER MAX. UNIT field-effect power transistor in a plastic envelope. VDS Drain-source voltage 60 V The device is intended for use in ID Drain current (DC) 43 A Automotive applications, Switched Ptot Total power dissipatio

GENERAL DESCRIPTION QUICK REFERENCE DATA N-channel enhancement mode SYMBOL PARAMETER MAX. MAX. UNIT field-effect power transistor in a plastic envelope. BUK453 -60A -60B The device is intended for use in VDS Drain-source voltage 60 60 V Switched Mode Power Supplies ID Drain current (DC) 22 20 A (SMP