Download: DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 10 V

DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected power MOSFET ina3pin plastic envelope, intended VDS Continuous drain source voltage 50 V as a general purpose switch for ID Continuous drain current 50 A automotive systems and other PD Total power dissipation 125 W applications. Tj Continuous junction temperature 150 ˚C RDS(ON) Drain-source on-state resistance 28 mΩ APPLICATIONS VIS = 10 V General controller for driving lamps motors solenoids heaters FEATURES FUNCTIONAL BLOCK DIAGRAM Vertical power DMOS output stage DRAIN Low on-state res...
Author: Sheyes1981 Shared: 8/19/19
Downloads: 202 Views: 772

Content

DESCRIPTION QUICK REFERENCE DATA

Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected power MOSFET ina3pin plastic envelope, intended VDS Continuous drain source voltage 50 V as a general purpose switch for ID Continuous drain current 50 A automotive systems and other PD Total power dissipation 125 W applications. Tj Continuous junction temperature 150 ˚C RDS(ON) Drain-source on-state resistance 28 mΩ

APPLICATIONS VIS = 10 V

General controller for driving lamps motors solenoids heaters

FEATURES FUNCTIONAL BLOCK DIAGRAM

Vertical power DMOS output stage DRAIN Low on-state resistance Overload protection against over temperature Overload protection against O/V short circuit load Latched overload protection CLAMP reset by input POWERINPUT 10 V input level RIG MOSFET Low threshold voltage also allows5Vcontrol Control of power MOSFET and supply of overload LOGIC AND protection circuits PROTECTION derived from input ESD protection on input pin Overvoltage clamping for turn off of inductive loads

SOURCE

Fig.1. Elements of the TOPFET.

PINNING - TO220AB PIN CONFIGURATION SYMBOL

PIN DESCRIPTION tabD1input TOPFET 2 drain I

P

3 source tab drain123SJanuary 1993 1 Rev 1.200,

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum Rating System (IEC 134) SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VDSS Continuous off-state drain source VIS = 0 V - 50 V voltage1 VIS Continuous input voltage - 0 11 V ID Continuous drain current Tmb ≤ 25 ˚C; VIS = 10 V - 50 A ID Continuous drain current Tmb ≤ 100 ˚C; VIS = 10 V - 31 A IDRM Repetitive peak on-state drain current Tmb ≤ 25 ˚C; VIS = 10 V - 200 A PD Total power dissipation Tmb ≤ 25 ˚C - 125 W Tstg Storage temperature - -55 150 ˚C Tj Continuous junction temperature 2 normal operation - 150 ˚C Tsold Lead temperature during soldering - 250 ˚C

OVERLOAD PROTECTION LIMITING VALUES

With the protection supply provided via the input pin, TOPFET can protect itself from two types of overload. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VISP Protection supply voltage 3 for valid protection 5 - V Over temperature protection VDDP(T) Protected drain source supply voltage VIS = 10 V - 50 V Short circuit load protection VDDP(P) Protected drain source supply voltage 4 VIS = 10 V - 16 V VIS = 5 V - 24 V PDSM Instantaneous overload dissipation Tmb = 25 ˚C - 2.1 kW

OVERVOLTAGE CLAMPING LIMITING VALUES

At a drain source voltage above 50 V the power MOSFET is actively turned on to clamp overvoltage transients. SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT IDROM Repetitive peak clamping current VIS = 0 V - 50 A EDSM Non-repetitive clamping energy Tmb ≤ 25 ˚C; IDM = 25 A; - 1 J VDD ≤ 25 V; inductive load EDRM Repetitive clamping energy Tmb ≤ 85 ˚C; IDM = 16 A; - 80 mJ VDD ≤ 20 V; f = 250 Hz

ESD LIMITING VALUE

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT VC Electrostatic discharge capacitor Human body model; - 2 kV voltage C = 250 pF; R = 1.5 kΩ 1 Prior to the onset of overvoltage clamping. For voltages above this value, safe operation is limited by the overvoltage clamping energy. 2 A higher Tj is allowed as an overload condition but at the threshold Tj(TO) the over temperature trip operates to protect the switch. 3 The input voltage for which the overload protection circuits are functional. 4 The device is able to self-protect against a short circuit load providing the drain-source supply voltage does not exceed VDDP(P) maximum. For further information, refer to OVERLOAD PROTECTION CHARACTERISTICS. January 1993 2 Rev 1.200,

THERMAL CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Thermal resistance Rth j-mb Junction to mounting base - - 0.8 1.0 K/W Rth j-a Junction to ambient in free air - 60 - K/W

STATIC CHARACTERISTICS

Tmb = 25 ˚C unless otherwise specified SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT V(CL)DSS Drain-source clamping voltage VIS = 0 V; ID = 10 mA 50 - - V V(CL)DSS Drain-source clamping voltage VIS = 0 V; IDM = 2 A; tp ≤ 300 µs; - - 70Vδ≤ 0.01 IDSS Zero input voltage drain current VDS = 12 V; VIS = 0 V - 0.5 10 µA IDSS Zero input voltage drain current VDS = 50 V; VIS = 0 V - 1 20 µA IDSS Zero input voltage drain current VDS = 40 V; VIS = 0 V; Tj = 125 ˚C - 10 100 µA RDS(ON) Drain-source on-state IDM = 25 A; VIS = 10 V - 22 28 mΩ resistance tp ≤ 300 µs; δ ≤ 0.01 VIS = 5 V - 30 35 mΩ

OVERLOAD PROTECTION CHARACTERISTICS

TOPFET switches off when one of the overload thresholds is reached. It remains latched off until reset by the input. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Short circuit load protection1 Tmb = 25 ˚C; L ≤ 10 µH EDS(TO) Overload threshold energy VDD = 13 V; VIS = 10 V - 1.1 - J td sc Response time VDD = 13 V; VIS = 10 V - 0.8 - ms Over temperature protection Tj(TO) Threshold junction temperature VIS = 10 V; from I ≥ 2 A2D 150 - - ˚C

INPUT CHARACTERISTICS

Tmb = 25 ˚C unless otherwise specified. The supply for the logic and overload protection is taken from the input. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VIS(TO) Input threshold voltage VDS = 5 V; ID = 1 mA 1.0 1.5 2.0 V IIS Input supply current VIS = 10 V; normal operation - 0.4 1.0 mA VISR Protection reset voltage 3 2.0 2.6 3.5 V VISR Protection reset voltage Tj = 150 ˚C 1.0 - - IISL Input supply current VIS = 10 V; protection latched2620 mA V(BR)IS Input clamp voltage II = 10 mA 11 13 - V RIG Input series resistance to gate of power MOSFET - 1.5 - kΩ 1 The short circuit load protection is able to save the device providing the instantaneous on-state dissipation is less than the limiting value for PDSM, which is always the case when VDS is less than VDSP maximum. Refer to OVERLOAD PROTECTION LIMITING VALUES. 2 The over temperature protection feature requires a minimum on-state drain source voltage for correct operation. The specified minimum ID ensures this condition. 3 The input voltage below which the overload protection circuits will be reset. January 1993 3 Rev 1.200,

TRANSFER CHARACTERISTICS

Tmb = 25 ˚C SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT gfs Forward transconductance VDS = 10 V; IDM = 25 A tp ≤ 300 µs; 17 28 - S δ ≤ 0.01 I Drain current1D(SC) VDS = 13 V; VIS = 10 V - 150 - A

SWITCHING CHARACTERISTICS

Tmb = 25 ˚C. RI = 50 Ω . Refer to waveform figures and test circuits. SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT td on Turn-on delay time VDD = 13 V; VIS = 10 V - 1.5 - µs tr Rise time resistive load RL = 1.1 Ω - 5.5 - µs td off Turn-off delay time VDD = 13 V; VIS = 0 V - 13 - µs tf Fall time resistive load RL = 1.1 Ω - 9 - µs td on Turn-on delay time VDD = 13 V; VIS = 10 V - 1.5 - µs tr Rise time inductive load IDM = 11 A - 1.3 - µs td off Turn-off delay time VDD = 13 V; VIS = 0 V - 18 - µs tf Fall time inductive load IDM = 11 A - 1.4 - µs

REVERSE DIODE LIMITING VALUE

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT IS Continuous forward current Tmb ≤ 25 ˚C; VIS = 0 V - 50 A

REVERSE DIODE CHARACTERISTICS

Tmb = 25 ˚C SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT VSDS Forward voltage IS = 50 A; VIS = 0 V; tp = 300 µs - 1.0 1.5 V trr Reverse recovery time not applicable 2 - - - -

ENVELOPE CHARACTERISTICS

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT Ld Internal drain inductance Measured from contact screw on - 3.5 - nH tab to centre of die Ld Internal drain inductance Measured from drain lead 6 mm - 4.5 - nH from package to centre of die Ls Internal source inductance Measured from source lead 6 mm - 7.5 - nH from package to source bond pad 1 During overload before short circuit load protection operates. 2 The reverse diode of this type is not intended for applications requiring fast reverse recovery. January 1993 4 Rev 1.200, PD% Normalised Power Derating Zth / (K/W) BUK102-50GS120 10 901D= 80 0.5 70 0.2 60 0.1 0.1 50 0.05 40 0.02 30 0.01 P tpp0DD= t

T

Tt00.001 0 20 40 60 80 100 120 140 1E-07 1E-05 1E-03 1E-01 1E+01 Tmb / C t / s

Fig.2. Normalised limiting power dissipation. Fig.5. Transient thermal impedance. PD% = 100⋅PD/PD(25 ˚C) = f(Tmb) Zth j-mb = f(t); parameter D = tp/T

ID% Normalised Current Derating ID / A BUK102-50GS 120 180 110 11 160 10 VIS / V = 100 9 90 140 80 120 70 7 50 80 40 60 5 40 4 10 20300020 40 60 80 100 120 14004812 16 20 24 28 32 Tmb / C VDS / V

Fig.3. Normalised continuous drain current. Fig.6. Typical output characteristics, Tj = 25 ˚C. ID% = 100⋅ID/ID(25 ˚C) = f(Tmb); conditions: VIS = 5 V ID = f(VDS); parameter VIS; tp = 250 µs & tp < td sc

ID & IDM / A BUK102-50GS ID / A BUK102-50GS 1000 808910 Overload protection characteristics not shown VIS / V = 7 /ID

VD

S tp = 60 ) = 6100 (ON 10 us

RD

S 50 5 100 us 40 10 1 ms 30 4

DC

10 ms 20 100 ms10110 100 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 VDS / V VDS / V

Fig.4. Safe operating area. Tmb = 25 ˚C Fig.7. Typical on-state characteristics, Tj = 25 ˚C. ID & IDM = f(VDS); IDM single pulse; parameter tp ID = f(VDS); parameter VIS; tp = 250 µs January 1993 5 Rev 1.200

, RDSON / Ohm BUK102-50GS a 0.06 Normalised RDS(ON) = f(Tj) VIS / V = 5678910 0.05 1.5 0.04 1.0 0.03 0.02 0.5 0.0100020 40 60 80 100 120 140 160 -60 -40 -20 0 20 40 60 80 100 120 140 ID / A Tj / C Fig.8. Typical on-state resistance, Tj = 25 ˚C. Fig.11. Normalised drain-source on-state resistance. RDS(ON) = f(ID); parameter VIS; tp = 250 µs a = RDS(ON)/RDS(ON)25 ˚C = f(Tj); ID = 25 A; VIS = 10 V ID / A BUK102-50GS td sc / ms BUK102-50GS 160 10

PDSM

80100.10246810 12 0.1 1 10 VIS / V PDS / kW Fig.9. Typical transfer characteristics, Tj = 25 ˚C. Fig.12. Typical overload protection characteristics. ID = f(VIS) ; conditions: VDS = 10 V; tp = 250 µs td sc = f(PDS); conditions: VIS ≥ 5 V; Tj = 25 ˚C. gfs / S BUK102-50GS PDSM% 10 4000050 100 150 -60 -40 -20 0 20 40 60 80 100 120 140 ID / A Tmb / C Fig.10. Typical transconductance, Tj = 25 ˚C. Fig.13. Normalised limiting overload dissipation. gfs = f(ID); conditions: VDS = 10 V; tp = 250 µs PDSM% =100⋅PDSM/PDSM(25 ˚C) = f(Tmb) January 1993 6 Rev 1.200, Energy & Time BUK102-50GS IIS / mA BUK102-50GS 1.5 2.0 Energy / J 1.5 1.0 1.0 Time / ms 0.5 0.5 Tj(TO) 0 0 -60 -20 20 60 100 140 180 2200246810 12 14 Tmb / C VIS / V

Fig.14. Typical overload protection characteristics. Fig.17. Typical DC input characteristics, Tj = 25 ˚C. Conditions: VDD = 13 V; VIS = 10 V; SC load = 30 mΩ IIS = f(VIS); normal operation

ID / A BUK102-50GS IIS / mA BUK102-50GS 50 10 40 8 PROTECTION LATCHED 30 typ. 6 20 4 RESET

NORMAL

1020050 60 700246810 12 14 VDS / V VIS / V

Fig.15. Typical clamping characteristics, 25 ˚C. Fig.18. Typical DC input characteristics, Tj = 25 ˚C. ID = f(VDS); conditions: VIS = 0 V; tp ≤ 50 µs IISL = f(VIS); overload protection operated ⇒ ID = 0 A

VIS(TO) / V IS / A BUK102-50GS max. typ. min. 0 0 -60 -40 -20 0 20 40 60 80 100 120 140 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2 Tj / C VSD / V

Fig.16. Input threshold voltage. Fig.19. Typical reverse diode current, Tj = 25 ˚C. VIS(TO) = f(Tj); conditions: ID = 1 mA; VDS = 5 V IS = f(VSDS); conditions: VIS = 0 V; tp = 250 µs January 1993 7 Rev 1.200

, VDD VDD = VCL RL LDtp: adjust for correct IDDDTOPFET TOPFETIIPD.U.T. P D.U.T. RIRIVIS S VIS S ID measure ID measure 0V 0V 0R1 0R1

Fig.20. Test circuit for resistive load switching times. Fig.23. Test circuit for inductive load switching times.

RESISTIVE TURN-ON BUK102-50GS INDUCTIVE TURN-ON BUK102-50GS 15 VDS / V ID / AVDS / V 90% VIS / V td on ID / A 10 90% td on VIS / V tr tr 10% 10% 10% 10% 00010 20 0 10 20 time / us time / us

Fig.21. Typical switching waveforms, resistive load. Fig.24. Typical switching waveforms, inductive load. VDD = 13 V; RL = 1.1 Ω; RI = 50 Ω, Tj = 25 ˚C. VDD = 13 V; ID = 11 A; RI = 50 Ω, Tj = 25 ˚C.

RESISTIVE TURN-OFF BUK102-50GS INDUCTIVE TURN-OFF BUK102-50GS td off VDS / V td off ID / A 90% VDS / V ID / A 10 90% 10 90% 90% tf VIS / V tf 5 VIS / V 10% 10% 00010 20 30 40 50 0 10 20 30 40 50 time / us time / us

Fig.22. Typical switching waveforms, resistive load. Fig.25. Typical switching waveforms, inductive load. VDD = 13 V; RL = 1.1 Ω; RI = 50 Ω, Tj = 25 ˚C. VDD = 13 V; ID = 11 A; RI = 50 Ω, Tj = 25 ˚C. January 1993 8 Rev 1.200

, EDSM% Iiso normalised to 25 C 100 1.5 50100.5 0 20 40 60 80 100 120 140 -60 -20 20 60 100 140 180 Tmb / C Tj / C

Fig.26. Normalised limiting clamping energy. Fig.29. Normalised input current (normal operation). EDSM% = f(Tmb); conditions: ID = 25 A; VIS = 10 V IIS/IIS25 ˚C = f(Tj); VIS = 10 V

V(CL)DSS Iisl normalised to 25 C

VDS

VDD + VDD0 1.5 ID L

VDS

0 - VIS D TOPFET -ID/10010D.U.T.I

P

Schottky R 01 RIS S shunt 0.5 -60 -20 20 60 100 140 180 Tj / C

Fig.27. Clamping energy test circuit, RIS = 50 Ω.

= ⋅ 2 ⋅ /( − ) Fig.30. Normalised input current (protection latched).EDSM 0.5 LID V(CL)DSS V(CL)DSS VDD IISL/IISL25 ˚C = f(Tj); VIS = 10 V Idss VDDP(P) / V BUK102-50GS 1 mA 50 100 uA 10 uA max typ. 20 1 uA 100 nA0020 40 60 80 100 120 1400246810 Tj / C VIS / V

Fig.28. Typical off-state leakage current. Fig.31. Maximum drain source supply voltage for IDSS = f(Tj); Conditions: VDS = 40 V; IIS = 0 V. SC load protection. VDDP(P) = f(VIS); Tmb ≤ 150 ˚C January 1993 9 Rev 1.200

, MECHANICAL DATA Dimensions in mm 4,5 Net Mass: 2 g max 10,3 max 1,3 3,7 2,8 5,9 min 15,8 max 3,0 max not tinned 3,0 13,5 min 1,3 max123(2x) 0,9 max (3x) 0,6 2,54 2,54 2,4 Fig.32. TO220AB; pin 2 connected to mounting base. Notes 1. Accessories supplied on request: refer to mounting instructions for TO220 envelopes. 2. Epoxy meets UL94 V0 at 1/8". January 1993 10 Rev 1.200,

DEFINITIONS

Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. Philips Electronics N.V. 1995 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. January 1993 11 Rev 1.200]
15

Similar documents

DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 5 V
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected logic level power MOSFET ina3pin plastic VDS Continuous drain source voltage 50 V envelope, intended as a general ID Continuous drain current 45 A purpose switch for automotive PD Total power di
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected logic level power MOSFET ina3pin plastic VDS Continuous drain source voltage 50 V envelope, intended as a general ID Continuous drain current 45 A purpose switch for automotive PD Total power di
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 10 V
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected power MOSFET ina3pin plastic envelope, intended VDS Continuous drain source voltage 50 V as a general purpose switch for ID Continuous drain current 29 A automotive systems and other PD Total po
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 5 V
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected logic level power MOSFET ina3pin plastic VDS Continuous drain source voltage 50 V envelope, intended as a general ID Continuous drain current 26 A purpose switch for automotive PD Total power di
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected logic level power MOSFET ina3pin plastic VDS Continuous drain source voltage 50 V envelope, intended as a general ID Continuous drain current 26 A purpose switch for automotive PD Total power di
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 10 V
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected power MOSFET ina3pin plastic envelope, intended VDS Continuous drain source voltage 50 V as a general purpose switch for ID Continuous drain current 15 A automotive systems and other PD Total po
DESCRIPTION QUICK REFERENCE DATA APPLICATIONS VIS = 5 V
DESCRIPTION QUICK REFERENCE DATA Monolithic temperature and SYMBOL PARAMETER MAX. UNIT overload protected logic level power MOSFET ina3pin plastic VDS Continuous drain source voltage 50 V envelope, intended as a general ID Continuous drain current 13.5 A purpose switch for automotive PD Total power
HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR
BUH515D HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR ■ STMicroelectronics PREFERRED SALESTYPE ■ HIGH VOLTAGE CAPABILITY ■ U.L. RECOGNISED ISOWATT218 PACKAGE (U.L. FILE # E81734 (N)) ■ NPN TRANSISTOR WITH INTEGRATED FREEWHEELING DIODE APPLICATIONS: 3 ■ HORIZONTAL DEFLECTION FOR COLOUR 1 TV DESCR
HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR
BUH515 HIGH VOLTAGE FAST-SWITCHING NPN POWER TRANSISTOR ■ HIGH VOLTAGE CAPABILITY ■ U.L. RECOGNISED ISOWATT218 PACKAGE (U.L. FILE # E81734 (N)). APPLICATIONS: ■ HORIZONTAL DEFLECTION FOR COLOUR TV AND MONITORS ■ SWITCH MODE POWER SUPPLIES 3 DESCRIPTION ISOWATT218 The BUH515 is manufactured using Mu
DISCRETE SEMICONDUCTORS DATA SHEET BYD37 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of April 1992
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D121 BYD37 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION and fatigue free as coefficients of expansion of
DISCRETE SEMICONDUCTORS DATA SHEET BYD33 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of October 1994
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D119 BYD33 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of October 1994 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION and fatigue free as coefficients of expansion o
DISCRETE SEMICONDUCTORS DATA SHEET BYD31 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of December 1991
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D122 BYD31 series Fast soft-recovery controlled avalanche rectifiers Product specification 1996 Jun 05 Supersedes data of December 1991 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION and fatigue free as coefficients of expansion
DISCRETE SEMICONDUCTORS DATA SHEET BYD17 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of November 1993 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D121 BYD17 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of November 1993 File under Discrete Semiconductors, SC01 FEATURES • Glass passivated • High maximum operating temperature handbook, 4 columnska
DISCRETE SEMICONDUCTORS DATA SHEET BYD13 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D119 BYD13 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES • Glass passivated • High maximum operating temperature handbook, 4 columnska• L
DISCRETE SEMICONDUCTORS DATA SHEET BYD11 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D122 BYD11 series Controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES • Glass passivated • High maximum operating temperature ahandbook, full pagewidt
DISCRETE SEMICONDUCTORS DATA SHEET BY8400 series Fast high-voltage soft-recovery rectifiers Product specification 1996 May 24 Supersedes data of June 1994
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D117 BY8400 series Fast high-voltage soft-recovery rectifiers Product specification 1996 May 24 Supersedes data of June 1994 File under Discrete Semiconductors, SC01 Fast high-voltage soft-recovery BY8400 series rectifiers FEATURES • Glass pas
DISCRETE SEMICONDUCTORS DATA SHEET BY8100 series Very fast high-voltage soft-recovery controlled avalanche rectifiers Product specification 1996 May 24
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D117 BY8100 series Very fast high-voltage soft-recovery controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of October 1994 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION expansion of all used parts
DISCRETE SEMICONDUCTORS DATA SHEET BY8000 series Fast high-voltage soft-recovery controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of June 1994
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D117 BY8000 series Fast high-voltage soft-recovery controlled avalanche rectifiers Product specification 1996 May 24 Supersedes data of June 1994 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION expansion of all used parts are mat
DATA SHEET BY614 Miniature high-voltage soft-recovery rectifier
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D189 BY614 Miniature high-voltage soft-recovery rectifier Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION expansion of all used parts are matched. • Glass passivated
DISCRETE SEMICONDUCTORS DATA SHEET BY584 High-voltage soft-recovery rectifier Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D189 BY584 High-voltage soft-recovery rectifier Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION expansion of all used parts are matched. • Glass passivated Rugged gla
DISCRETE SEMICONDUCTORS DATA SHEET BY527 Controlled avalanche rectifier Product specification 1996 Jun 11 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D116 BY527 Controlled avalanche rectifier Product specification 1996 Jun 11 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION This package is hermetically sealed and fatigue free as coefficients of • G
DISCRETE SEMICONDUCTORS DATA SHEET BY505 High-voltage soft-recovery rectifier Product specification 1996 May 28 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, halfpage M3D189 BY505 High-voltage soft-recovery rectifier Product specification 1996 May 28 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION expansion of all used parts are matched. • Glass passivated Rugged gla
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - SOD100 PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a full pack plastic envelope, featuring fast forward VRRM Repetitive peak reverse voltage 1500 V recovery and low forward recovery VF Forward voltage 1.2 V voltage. The device is i
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - TO220AC PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a plastic envelope, featuring fast forward recovery and VRRM Repetitive peak reverse voltage 1500 V low forward recovery voltage. The VF Forward voltage 1.2 V device is intended fo
DISCRETE SEMICONDUCTORS DATA SHEET BY448 Damper diode Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D116 BY448 Damper diode Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION This package is hermetically sealed and fatigue free as coefficients of • Glass passivated Ru
DISCRETE SEMICONDUCTORS DATA SHEET BY428 Damper diode Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01
DISCRETE SEMICONDUCTORS DATA SHEET handbook, 2 columns M3D118 BY428 Damper diode Product specification 1996 May 24 Supersedes data of April 1992 File under Discrete Semiconductors, SC01 FEATURES DESCRIPTION This package is hermetically sealed and fatigue free as coefficients of • Glass passivated Ru
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - SOD113 PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a full pack plastic envelope featuring low forward VRRM Repetitive peak reverse voltage 1500 V voltage drop, fast reverse recovery VF Forward voltage 1.5 V and soft recovery charac
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - SOD100 PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a full pack plastic envelope featuring low forward VRRM Repetitive peak reverse voltage 1500 V voltage drop, fast reverse recovery VF Forward voltage 1.5 V and soft recovery charac
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - TO220AC PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. UNIT rectifier diode in a plastic envelope featuring low forward voltage drop, VRRM Repetitive peak reverse voltage 1500 V fast reverse recovery and soft VF Forward voltage 1.5 V recovery characteristic.
GENERAL DESCRIPTION QUICK REFERENCE DATA PINNING - TO220AC PIN CONFIGURATION SYMBOL
GENERAL DESCRIPTION QUICK REFERENCE DATA Glass-passivated double diffused SYMBOL PARAMETER MAX. MAX. MAX. UNIT rectifier diodes in a plastic envelope featuring low forward voltage drop, BY329 -800 -1000 -1200 fast reverse recovery and soft VRRM Repetitive peak reverse 800 1000 1200 V recovery charac