Download: Tecra 780CDM / 780DVD Disassembly Overview

Tecra 780CDM / 780DVD Disassembly Overview The information offered in this section is an overview of the Maintenance Manual, Chapter 4, Replacement Procedures. If you have any questions or concerns regarding the proper procedure please refer to the Mainte- nance Manual through the Toshiba Service and Support Website before you proceed. This section explains how to remove Field Replaceable Units (FRUs). It may not be neces- sary to remove all the FRUs in order to replace one. The chart is a guide to which FRUs need to be removed in order to remove others. The section numbers on the chart refer ...
Author: Anonymous
Downloads: 0 Views: 0

Content

Tecra 780CDM / 780DVD Disassembly Overview

The information offered in this section is an overview of the Maintenance Manual, Chapter 4, Replacement Procedures. If you have any questions or concerns regarding the proper procedure please refer to the Mainte- nance Manual through the Toshiba Service and Support Website before you proceed. This section explains how to remove Field Replaceable Units (FRUs). It may not be neces- sary to remove all the FRUs in order to replace one. The chart is a guide to which FRUs need to be removed in order to remove others. The section numbers on the chart refer to the sections in the Maintenance Manual, Chapter 4. Always start by removing the battery pack, next, optional items such as the optional PC card and optional memory module, then follow the line on the chart to determine which FRU you must remove next in order to repair the one you think is causing the computer to operate improperly. To remove the battery pack, follow the steps below. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing; and do not twist or bend the battery pack. 2. Turn the computer upside down with the front facing you and push the battery lock up to unlock it. A red dot shows when the lock is in the unlock position. 3. Pull out the battery release lever and slide it to the left to pop the battery up slightly. 4. Grasp the battery pack and lift it out. To install the battery pack, follow the steps below. WARNING: The battery pack is a lithium ion battery which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba as replacements. NOTE: Check the battery terminals visually. If they are dirty, wipe them clean with a dry cloth. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Make sure the battery release lever is pulled out then carefully insert the new or recharged battery pack. 3. Place your fingers just above two pins on the battery pack that fit into the locking mechanisms in the battery socket. Push the battery pack down carefully until it locks into place. 4. Push the battery lock down to secure it. The red dot will be covered.

Toshiba TRR Page 7 4/00, Tecra

, To remove the optional PC card, make sure the computer is in boot mode, then follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack. 3. Open or remove the PC card slot cover. 4. Press in slightly on the eject button for the upper and/or lower card and the button will pop out fully. 5. Now, press the button firmly to pop the PC card out partially. 6. Grasp the PC card and remove it. 7. Close or replace the PC card slot cover. To install the PC card, follow the steps below. 1. Open or remove the PC card slot cover. 2. Insert the PC card and press gently to ensure a firm connection. 3. Close the slot cover or replace the cover with an appropriate one. 4. Install the battery pack. To remove the SelectBay module, follow the steps below. 2. Remove the battery pack. 3. Turn the computer upside down and slide the SelectBay lock to the unlock position, shown by a red box. 4. Pull out the release lever. 5. Push the release lever in firmly to pop the SelectBay module partially out of the bay. 6. Grasp the module and pull it out. CAUTION: The SelectBay modules can become hot with use. Be careful when removing the module. Install the SelectBay modules as described below. 1. Insert the module in the computer and press until it locks into place. 2. Fold the release lever into the closed position. 3. Slide the SelectBay lock to the locked position. The red box should not be visible. 4. Install the battery pack.

Toshiba TRR Page 8 4/00, Tecra

, You can use the SelectBay cover when you do not need to use a SelectBay module. 1. To install the cover, first remove the SelectBay module then hold the cover by the two finger grips and push it into place until you hear the latches click. 2. To remove the cover, grasp the two finger grips and pull the cover out. To disassemble the DVD-ROM drive, follow the steps below. 1. Remove six M2x3 silver screws and two M2.5x6 silver screws securing the frame to the DVD-ROM drive. 2. Remove the connector cover. 3. Remove the metal frame, connector board, and disconnect the flexible cable. î To disassemble the FDD, follow the steps below. 1. Remove six M2x6 silver screws. 2. Turn the FDD over and release two latches securing the upper plastic frame and lower plastic frame. Turn it back over and lift off the cover. 3. Lift off the upper shield cover, unseat the flexible cable connector from the lower plastic frame, then lift out the FDD. 4. Pull the flexible cable out of the FDD connector. ê 5. Remove four M2x3 silver screws andremove the FDD from the bracket. è

Toshiba TRR Page 9 4/00, Tecra

, To assemble the FDD, follow the steps below. 1. Seat the FDD in the bracket and secure the bracket with four M2x3 silver screws. Tighten screws to a torque of less than 2.2 kgfcm. 2. Insert the flexible cable into the connector. Press gently to assure a firm connection. 3. Seat the FDD in the lower plastic frame and set the upper shield cover in place. 4. Seat the flexible cable connector into the lower plastic frame. 5. Set the upper plastic frame in place, snap the two latches closed and secure six M2x6 silver screws. CAUTION: Be very careful not to press on the top or bottom of the HDD. Pressure can destroy data or damage the drive. To remove the HDD pack, follow the steps below. 2. Remove the battery pack. 3. Turn the computer upside down. 4. Slide the HDD cover to the right and push the HDD pack forward until the back edge is aligned with a marker next to the HDD slot. 5. Lift up on the cover to remove the HDD pack. To disassemble the HDD Pack, follow the steps below. 1. Slide the cover firmly in the direction of the arrow and remove it. 2. Remove the HDD tray and connector cover. í î Images / text continued on the next page

Toshiba TRR Page 10 4/00, Tecra

, Disassembling the HDD Pack, continued. 3. Remove four M2.5x6 silver screws from HDD pack. 4. Remove four M3x4 flat-head screws and the HDD frame. 5. Remove the flexible cable. CAUTION: Do not try to disconnect by pulling on the flexible cable. CAUTION: Do not apply pressure to the top or bottom of the HDD. í è To assemble the HDD pack, follow the steps below. 1. Connect the flexible cable connector to the HDD. 2. Seat the HDD frame on the HDD and secure it with four M3x4 flat-head screws. 3. Seat the connector cover on the flexible cable connector. Be sure to match the positioning pins to the holes on the flexible cable and metal cover. CAUTION: Do not hold the HDD by its flat surfaces. It may damage the HDD. 4. Secure four M2.5x6 silver screws. î 5. Seat the cover onto the HDD.

Toshiba TRR Page 11 4/00, Tecra

, To install the HDD pack, follow the steps below. 1. Align the HDD pack with the marker on the computer and seat the HDD so that tabs on the HDD fit into notches on the computer. 2. Make sure the cover is pushed fully to the right and push the HDD back to ensure a firm connection. 3. Slide the cover to the left to lock the HDD into the slot. 4. Install the battery pack. To remove the memory module(s), make sure the computer is in boot mode and follow the steps below. CAUTION: Do not try to remove a memory module(s) with the computer turned on. You can damage the computer and the memory module(s). 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the 2. Remove the battery pack and HDD pack. 3. Lift up the mylar cover. 4. Use a slender object (plastic card) to press the latches on either side of the memory module(s) to the outside and the memory module will pop up. 5. Grasp the memory module(s) by the sides and pull it out. CAUTION: Do not touch the connectors on the memory module(s) or on the computer. Debris on the connectors may cause memory access problems. The modem board is located under the palmrest. To open the palmrest, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, and HDD pack. 3. With the computer still upside down, remove two M2x8 silver screws, two î M2x22 silver screws and two M2x14silver screws. 4. Turn the computer right side up and open the display panel and PC card cover. 5. Grasp the sides of the palmrest and pull it forward until tabs on either side clear the holes on the top cover. Three latches are located under the palmrest as shown below. 6. Carefully lift the palmrest. î Images / text continued on the next page

Toshiba TRR Page 12 4/00, Tecra

, Opening the palmrest, continued. 7. Remove four M2x6 screws securing the modem board (or the dummy cover) and lift it out. To install a modem board, follow the steps below. 1. Connect the modem board to the corresponding connector in the computer. NOTE: Be sure a plastic insulator tab lies on top of the green backup battery, when you seat the modem board. 2. Make sure holes in the modem casing are aligned with screw holes on the í computer, then secure the modemboard module with four M2x6 screws. 3. Lay the palmrest in place and press down to seat it firmly. 4. Close the PC card slot cover and display panel. 5. Turn the computer upside down. 6. Secure two M2x22 silver screws, two M2x8 silver screws, and two M2x14 silver screws to the bottom of the 7. Install the HDD pack, optional PC card, and battery pack. To remove the backup and RTC batteries, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module and modem board. 3. Lift the backup battery mylar cover. 4. Disconnect the backup battery cable from PJ511 on the system board, unthread the cables and lift out the backup battery. 5. Disconnect the RTC battery from PJ510 on the system board, unthread the cables and lift it out.

Toshiba TRR Page 13 4/00, Tecra

, To remove the keyboard, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board and backup and RTC batteries. 3. Peel off the tape placed on the folded end of the keyboard flexible cable. 4. Disconnect the flexible cable from PJ580 on the system board. 5. Lift up the front edge of the keyboard and lift out the keyboard. To remove the membrane switch, follow the steps below. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, and keyboard. 3. Disconnect the membrane switch cable from PJ570 on the system board. 4. Remove two M2.5x4 screws securing the membrane switch unit and lift out the unit. To remove the top cover with display assembly, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard and mem- brane switch. 3. Remove six M2.5x10 silver screws from the bottom of the computer. 4. Remove the mask and two M2x6 screws from the position under the battery pack. 5. Remove three M2.5x4 silver screws from the back of the computer. î Images continued on the next page

Toshiba TRR Page 14 4/00, Tecra

, Removing the top cover with display assembly, continued. 6. Turn the computer right side up and open the display panel. 7. Slightly lift up the LCD cable cover and pull it forward to remove it, then remove the plastic lens. 8. Remove the tape off the LCD cables. 9. Remove one M2x6 screw securing the ground cable. 10. Disconnect the LCD cable, FL inverter cable, speaker cable and microphone cable. 11. Remove six M2x6 screws, one M2x8 screw and three M2x4 silver screws securing the top cover. 12. Open two port covers on the back of the computer. 13. Pull out the top cover just below the í composite video connector (yellow) torelease a latch. 14. Carefully lift up the back side of the top cover with display assembly. Lift slowly to avoid damage to the two latches on the left side of the computer. î í

Toshiba TRR Page 15 4/00, Tecra

, To remove the speakers, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch and top cover with display assembly. 3. Lay the display down. Partially lift the insulator covering the speaker cables. 4. Remove four M2x4 screws securing the speaker holders. 5. Observe how the cables are threaded, then lift out the speakers, cables and holders. 6. Pull the speakers out of the holders. To remove the system board, follow the steps below. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assembly. 3. Remove one M2x4 silver screw and two M2.5x6 screws securing the shield plate and remove it. 4. Remove one M2.5x4 screw near the PC card slot. 5. Remove one M2.5x4 screw securing the connection board and lift it out. 6. Remove one M2.5x6 screw under the connection board. 7. Remove one M2x4 silver screw ê securing the USB slot to the USBconnector. CAUTION: Do not remove the heat-sink on the CPU. The grease can dry out and cause damage to the CPU. 8. Lift up the system board to disconnect three connectors.

Toshiba TRR Page 16 4/00, Tecra

, To remove the fan, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assembly, and system board. 3. Turn the system board upside down and remove tape securing the fan cable. 4. Disconnect the fan cable from PJ550 on the system board. 5. Turn the system board right side up and remove two M2.5x4 screws. 6. Lift out the fan. To remove the middle frame, follow the steps below. 2. Remove the battery pack, optional PC card, HDD PACK, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assembly, and system board. 3. Remove two M2.5x6 screws and one M2.5x8 screw securing the SelectBay top cover to the middle frame. 4. Two positioning pins fit into holes on the SelectBay top cover, so lift the cover straight up to clear the pins. 5. Remove three M2.5x10 silver screws securing the CONN holder assembly ê and lift out the CONN holder assembly.6. Disconnect two secondary battery cables (PJ511 and PJ512) from the I/O board and remove the cables with the protective metal plate. 7. Remove two M2.5x8 screws securing the middle frame to the bottom cover. 8. Pull out the SelectBay release lever and set the SelectBay lock to the lock position. CAUTION: Make sure the SelectBay lock is locked before removing the middle frame from the bottom cover. If you remove the middle frame while the SelectBay lock is unlocked, the I/O board will be damaged. NOTE: Make sure the screw in the memory slot has been removed. 9. Remove the middle frame from the base of the computer.

Toshiba TRR Page 17 4/00, Tecra

, To install the middle frame, follow the steps below. 1. Make sure the SelectBay release lever is extended and the SelectBay lock is in the locked position. 2. Seat the middle frame and make sure a small tongue on the middle frame’s SelectBay locking mechanism fits into a corresponding notch on the external SelectBay lock. 3. First secure one M2.5x8 screw next to the SelectBay lock arm, then secure the other M2.5x8 screw. 4. Place the CONN holder assembly and secure it with three M2.5x10 silver screws. 5. Connect two secondary battery cables to the I/O board. 6. Seat the protective metal plate. 7. Thread the battery cables in the groove and seat the cable holder. 8. Replace the tape. 9. Secure the SelectBay top cover with two M2.5x6 screws and one M2.5x8 screw. 10. Install the system board, top cover with display assembly, membrane switch, keyboard, backup and RTC batteries, modem board, optional memory module, HDD pack, optional PC card, and battery pack. To remove the I/O board, follow the steps. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assembly, system board, and middle frame. 3. From the bottom of the battery pack slot, push up on the battery jumper contact and slide it forward. 4. Press down on the battery jumper as shown in the figure below and slide the jumper out to remove it. î 5. Remove one M2x6 screw securing theI/O board to the bottom cover. 6. Lift out the I/O board. 7. Lift out the base shield assembly (with rubber heat conductor).

Toshiba TRR Page 18 4/00, Tecra

, To remove the display mask, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack. 3. Remove two rubber seals at the bottom corners of the display assembly. 4. Remove two M2.5x6 screws that were covered by the rubber seals. NOTE: Support the display with your hand when you remove the screws. í 5. Using the fingers of both hands, carefully release the 18 latches along the edges of the display mask. Begin at the top (six latches), continue along the sides (four latches on each side) and the bottom (four latches). To remove the FL inverter board, follow the steps below. external cables connected to the computer. 2. Remove the battery pack and the display mask. 3. Lay the display panel on its back. 4. Remove two M2.5x6 screws securing the FL inverter board. 5. Lift up the FL inverter board and disconnect the FL cable. 6. Rotate out the top end of the FL inverter board. Disconnect the FL inverter cable and lift out the FL inverter board. î

Toshiba TRR Page 19 4/00, Tecra

, NOTE: Be careful not to apply pressure to the ICs along the edge of the LCD module. The ICs are easily damaged. To remove the LCD module, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, display mask and FL inverter board as described in Sections 4.2, 4.19 and 4.20. 3. Remove four M2.5x8 screws securing the LCD module to the display assem- bly. 4. Carefully rotate out the top of the LCD module enough to access the display cable. 5. Peel off the tape securing the cable and disconnect the cable. To remove the microphone, follow the steps below. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assembly, and speakers. 3. Lay the top cover with display assembly down so that the bottom of the top cover lies flat and faces up. 4. Remove one M2x4 screw securing the hinge cover and one M2.5x6 screw securing a plastic cable guide. 5. Remove one M2.5x4 screw holding the microphone ground cable. 6. Release the cable guide from the top cover at the top right corner of the left speaker cable groove. 7. Lift the small end of the cable guide about 2.5 cm, then use tweezers to ê push down the LCD cable core to freethe cable guide. 8. Lift the cable guide straight up and pull the microphone cable out of the cable guide. 9. Rotate the top cover up about 90 degrees. NOTE: Grasp the top cover by the sides when you rotate it up. Do not pull at the center. 10. Lift out the microphone holder and cable and remove the microphone from the holder.

Toshiba TRR Page 20 4/00, Tecra

, CAUTION: When you remove the FL, be careful not to let any dust or other foreign matter contaminate the LCD panel. Any contamination can affect the performance of the unit. To remove the FL, follow the steps below. 1. Turn off the power to the computer. Disconnect the AC adapter and all external cables connected to the computer. 2. Remove the battery pack, optional PC card, HDD pack, optional memory module, modem board, backup and RTC batteries, keyboard, membrane switch, top cover with display assem- bly, speakers, display mask, FL inverter board, LCD module, and microphone. 3. Remove one strip of tape securing the FL cable to the LCD frame and lift up ê the FL cable.4. Remove two M2x4 thin-head silver screws and one M2x2 thin-head silver screw to remove the metal FL cover. 5. Carefully lift up the white sheet cover- ing the FL. 6. Lift the yellow FL cable connector until one end is out of the groove. CAUTION: Handle only the FL cable instead of the FL glass tube to minimize risk of damage or injury. 7. Lift the white FL cable out of its groove to remove the cable and FL. î

Toshiba TRR Page 21 4/00, Tecra

]
15

Similar documents

Tecra 750 Series Disassembly Overview
Tecra 750 Series Disassembly Overview The information offered in this section is an overview of the Maintenance Manual, Chapter 4, Replacement Procedures. If you have any questions or concerns regarding the proper procedure please refer to the Mainte- nance Manual through the Toshiba Service and Sup
TM Satellite Pro GENERAL INFORMATION
TM Satellite Pro GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0&1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure t
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. 5mm Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that the main
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0&1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that the main b
FIELD REPLACEABLE UNIT DOCUMENTATION TM GENERAL INFORMATION Before attempting any of the following procedures, make sure that the main battery and AC adaptor is
FIELD REPLACEABLE UNIT DOCUMENTATION TM GENERAL INFORMATION For Parts listing use TOSHFAX Doc: 3440CT(PP344C-2PU82): #7219 3480CT(PP348C-4PU82): #7228 Before attempting any of the following procedures, make sure that the main battery and AC adaptor is not connected to the unit and the environment in
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips screwdriver (Size 0) 2. Phillips Screwdriver (Size 1) 3. Flat head screwdriver (5mm) 4. Hex driver (5mm) 5. Security Torx(Size8) 6. Case Separator 7. ESD Wrist Strap 8. ESD mats 9. Tweezers Before attempting any
TM GENERAL INFORMATION Before attempting any of the following procedures,
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. 5mm Flat head Screwdriver 3. Case Separator 4. ESD Wrist Strap 5. ESD mats 6. Tweezers Before attempting any of the following procedures, make sure that the main battery and AC adaptor is
FIELD REPLACEABLE UNIT DOCUMENTATION
TM 1700 Series GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. Flat head screwdriver (5mm) 3. Hex driver (5mm) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that
Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar
PCG-GR150/GR150K/GR170/GR170K SERVICE MANUAL For American Area US Model Canadian Model S400 Lineup : PCG-GR150 PCG-GR150K PCG-GR170 PCG-GR170K Illust : PCG-GR170K entia l onfidC NOTEBOOK COMPUTER 9-872-218-11 Information in this document is subject to change without notice. Caution Markings for Lith
Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar
PCG-FX777/FX877 SERVICE MANUAL For American Area Latin Model Ver 1-2001J All the supplementary information are attached at the end of data files. Update List S400 Lineup : PCG-FX777 PCG-FX877 Illust : PCG-FX877 ial onfid ent C NOTEBOOK COMPUTER 9-872-288-01 Information in this document is subject to
PCGA-DSD5/DSM5 SERVICE MANUAL US Model ial
PCGA-DSD5/DSM5 SERVICE MANUAL US Model Canadian Model S400 ial Specifications nt Drive performance Operating humidity CD-RW/DVD Docking Station (PCGA-DSM5) e 20 % to 80 % (not condensed), provided that humidity is Reading speed: 24X max. CD-ROM/CD-R reading,d less than 65 % at 95 °F (35 °C) 12X max.
Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar
PCG-SR27/SR27K SERVICE MANUAL US Model Canadian Model S400 Illust : PCG-SR27K tial onfid en C NOTEBOOK COMPUTER 9-872-215-11 Information in this document is subject to change without notice. Caution Markings for Lithium/Ion Battery - The following or similar texts shall be provided on battery pack o
Satellite® 2 Model: Satellite ® 1400/1405 Series
Satellite® 1400/1405 Series User’s Guide If you need assistance: InTouch® Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see Chapter 9 on page 219 in this guide. TOSHIBA C6616-1002M2 Model: Satellite ® 1400/1405 Seri
Viking Memory
Viking Memory 4. Locate the memory expan- INSTALLATIONGUIDEsion slot in the open compart- ® ment. Notice the location ofTOSHIBA the off-center key on the Portégé 300CT, 310CT, 320CT expansion slot. 5. To install a memory module, insert the module into the expansion slot at an angle and then push it
Viking Memory
Viking MemoryINSTALLATIONGUIDE6. Locate the holding screw at the ® top left corner of the open compart-TOSHIBA ment. Remove this screw with a Libretto 50CT & 70CT small Phillips head screwdriver. 7. To install the memory module, align the connector on the module with the con- nector in the system’s
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0&1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mat 7. Tweezers Before attempting any of the following procedures, make sure that the main ba
MEMORY INSTALLATION GUIDE: #1005020C
MEMORY INSTALLATION GUIDE: #1005020C Toshiba T1900, T1910, T1950, T1960, T4500, T4600, INSERT T4700, T4800, T4850 Description Viking P/N 4Mb Memory Credit Card T2012U, RT2012U 8Mb Memory Credit Card T2013U, RT2013U 16Mb Memory Credit Card T2014U, RT2014U 32Mb Memory Credit Card T2015U, RT2015U TOSHI
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdrivers (Size 1&0) 2. 3mm Flat head Screwdriver 3. Security Torx (Size 6) 4. Case Separator 5. ESD Wrist Strap 6. ESD mat 7. Tweezers Before attempting any of the following procedures, make sure that the ma
FIELD REPLACEABLE UNIT DOCUMENTATION TM GENERAL INFORMATION Before attempting any of the following procedures,
FIELD REPLACEABLE UNIT DOCUMENTATION TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0) 2. Flat head Screwdriver 3. Case Separator 4. ESD Wrist Strap 5. ESD mat 6. Tweezers Before attempting any of the following procedures, make sure that th
TM Tecra GENERAL INFORMATION
TM Tecra GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 0&1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that the
TM Tecra GENERAL INFORMATION
TM Tecra GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that the ma
Contents 18 Contents
Satellite® 2430/2435 Series User’s Guide If you need assistance: ❖ InTouch® Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 179 in this guide. TOSHIBA C6633-1202M1 Model: Satellit
Satellite® 2 Model: Satellite® 1410/1415
Satellite® 1410/1415 Series User’s Guide If you need assistance: InTouch® Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see Chapter 8 on page 201 in this guide. TOSHIBA C6624-1002M2 Model: Satellite® 1410/1415 Compa
Contents 12 Contents
Satellite® 1100 User’s Guide If you need assistance: ❖ InTouch® Center Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 177 in this guide. TOSHIBA C6622-1002M2 Model: Satellite 1100 Compa
TM GENERAL INFORMATION
TM GENERAL INFORMATION Tools Required for Proper Disassembly and Reassembly: 1. Phillips Screwdriver (Size 1) 2. 5mm Flat head Screwdriver 3. Security Torx (Size 7) 4. Case Separator 5. ESD Wrist Strap 6. ESD mats 7. Tweezers Before attempting any of the following procedures, make sure that the main
Copyright © 2001 by TOSHIBA Corporation. All rights reserved. Under the copyright laws,
TOSHIBA TE2000 Portable Personal Computer User’s Manual Copyright © 2001 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the
Cleaning the cartridge slot
Cleaning the cartridge slot Cleaning the cartridge slot Written By: tonymag28 INTRODUCTION Cleaning the cartridge slot will fix most of the problems with the Nintendo 64. TOOLS: Q-Tips (1) Compressed Air (1) © iFixit — CC BY-NC-SA www.iFixit.com Page 1 of 2 Cleaning the cartridge slot Step 1 — Clean